[U-Boot] [PATCH v3 10/12] i2c: Drop CONFIG_SYS_I2C_BOARD_LATE_INIT

[Heiko Schocher <hs@denx.de>]

Hello Simon,

Am 13.05.2017 um 05:09 schrieb Simon Glass:
> This option is not used by any boards. Drop it.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v3: None
> Changes in v2: None
>
>   README                       | 11 -----------
>   drivers/i2c/fsl_i2c.c        |  9 ---------
>   drivers/i2c/fti2c010.c       |  9 ---------
>   include/i2c.h                |  3 ---
>   scripts/config_whitelist.txt |  1 -
>   5 files changed, 33 deletions(-)

Thanks!

Applied to u-boot-i2c.git master

u-boot-i2c master just testing on travis:
https://travis-ci.org/hsdenx/u-boot-i2c/builds/232288665

bye,
Heiko
>
> diff --git a/README b/README
> index 9f9265dc6d..96ce6289ea 100644
> --- a/README
> +++ b/README
> @@ -2323,17 +2323,6 @@ The following options need to be configured:
>   		custom i2c_init_board() routine in boards/xxx/board.c
>   		is run early in the boot sequence.
>
> -		CONFIG_SYS_I2C_BOARD_LATE_INIT
> -
> -		An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
> -		defined a custom i2c_board_late_init() routine in
> -		boards/xxx/board.c is run AFTER the operations in i2c_init()
> -		is completed. This callpoint can be used to unreset i2c bus
> -		using CPU i2c controller register accesses for CPUs whose i2c
> -		controller provide such a method. It is called at the end of
> -		i2c_init() to allow i2c_init operations to setup the i2c bus
> -		controller on the CPU (e.g. setting bus speed & slave address).
> -
>   		CONFIG_I2CFAST (PPC405GP|PPC405EP only)
>
>   		This option enables configuration of bi_iic_fast[] flags
> diff --git a/drivers/i2c/fsl_i2c.c b/drivers/i2c/fsl_i2c.c
> index a1406baa87..ff3dc25927 100644
> --- a/drivers/i2c/fsl_i2c.c
> +++ b/drivers/i2c/fsl_i2c.c
> @@ -284,15 +284,6 @@ static void __i2c_init(const struct fsl_i2c_base *base, int speed, int
>
>   		break;
>   	}
> -
> -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
> -	/* Call board specific i2c bus reset routine AFTER the bus has been
> -	 * initialized. Use either this callpoint or i2c_init_board;
> -	 * which is called before i2c_init operations.
> -	 * For details about this problem see doc/I2C_Edge_Conditions.
> -	*/
> -	i2c_board_late_init();
> -#endif
>   }
>
>   static int
> diff --git a/drivers/i2c/fti2c010.c b/drivers/i2c/fti2c010.c
> index b35d0d2d9c..4da959fa53 100644
> --- a/drivers/i2c/fti2c010.c
> +++ b/drivers/i2c/fti2c010.c
> @@ -146,15 +146,6 @@ static void fti2c010_init(struct i2c_adapter *adap, int speed, int slaveaddr)
>   	set_i2c_bus_speed(chip, speed);
>
>   	/* slave init, don't care */
> -
> -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
> -	/* Call board specific i2c bus reset routine AFTER the bus has been
> -	 * initialized. Use either this callpoint or i2c_init_board;
> -	 * which is called before fti2c010_init operations.
> -	 * For details about this problem see doc/I2C_Edge_Conditions.
> -	*/
> -	i2c_board_late_init();
> -#endif
>   }
>
>   /*
> diff --git a/include/i2c.h b/include/i2c.h
> index cd7f61e1c1..a88cc7cddf 100644
> --- a/include/i2c.h
> +++ b/include/i2c.h
> @@ -706,9 +706,6 @@ void i2c_early_init_f(void);
>   #endif
>   void i2c_init(int speed, int slaveaddr);
>   void i2c_init_board(void);
> -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
> -void i2c_board_late_init(void);
> -#endif
>
>   #ifdef CONFIG_SYS_I2C
>   /*
> diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
> index da37e49c83..5cdca33f87 100644
> --- a/scripts/config_whitelist.txt
> +++ b/scripts/config_whitelist.txt
> @@ -4222,7 +4222,6 @@ CONFIG_SYS_I2C_BASE2
>   CONFIG_SYS_I2C_BASE3
>   CONFIG_SYS_I2C_BASE4
>   CONFIG_SYS_I2C_BASE5
> -CONFIG_SYS_I2C_BOARD_LATE_INIT
>   CONFIG_SYS_I2C_BOOT_EEPROM_ADDR
>   CONFIG_SYS_I2C_BUSES
>   CONFIG_SYS_I2C_BUS_MAX
>

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany