[U-Boot] [PATCH 07/13] ehci-mx5: Add missing OC_DIS for i.MX53

["Benoît Thébaudeau" <benoit.thebaudeau@advansee.com>]

The i.MX53 has MXC_H*_UCTRL_H*_OC_DIS_BIT bits to disable the oc pin.

Signed-off-by: Beno?t Th?baudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
---
 .../drivers/usb/host/ehci-mx5.c                    |   25 ++++++++++++++++++++
 1 file changed, 25 insertions(+)

diff --git u-boot-usb-76454b2.orig/drivers/usb/host/ehci-mx5.c u-boot-usb-76454b2/drivers/usb/host/ehci-mx5.c
index 8e42e56..7da1398 100644
--- u-boot-usb-76454b2.orig/drivers/usb/host/ehci-mx5.c
+++ u-boot-usb-76454b2/drivers/usb/host/ehci-mx5.c
@@ -32,12 +32,14 @@
 #define MXC_OTG_OFFSET			0
 #define MXC_H1_OFFSET			0x200
 #define MXC_H2_OFFSET			0x400
+#define MXC_H3_OFFSET			0x600
 
 #define MXC_USBCTRL_OFFSET		0
 #define MXC_USB_PHY_CTR_FUNC_OFFSET	0x8
 #define MXC_USB_PHY_CTR_FUNC2_OFFSET	0xc
 #define MXC_USB_CTRL_1_OFFSET		0x10
 #define MXC_USBH2CTRL_OFFSET		0x14
+#define MXC_USBH3CTRL_OFFSET		0x18
 
 /* USB_CTRL */
 #define MXC_OTG_UCTRL_OWIE_BIT		(1 << 27)	/* OTG wakeup intr enable */
@@ -51,10 +53,16 @@
 #define MXC_H1_OC_DIS_BIT		(1 << 5)	/* UH1 Disable Overcurrent Event */
 
 /* USBH2CTRL */
+#define MXC_H2_UCTRL_H2_OC_DIS_BIT	(1 << 30)
 #define MXC_H2_UCTRL_H2UIE_BIT		(1 << 8)
 #define MXC_H2_UCTRL_H2WIE_BIT		(1 << 7)
 #define MXC_H2_UCTRL_H2PM_BIT		(1 << 4)
 
+/* USBH3CTRL */
+#define MXC_H3_UCTRL_H3_OC_DIS_BIT	(1 << 30)
+#define MXC_H3_UCTRL_H3UIE_BIT		(1 << 8)
+#define MXC_H3_UCTRL_H3WIE_BIT		(1 << 7)
+
 /* USB_CTRL_1 */
 #define MXC_USB_CTRL_UH1_EXT_CLK_EN	(1 << 25)
 
@@ -196,9 +204,26 @@ int mxc_set_usbcontrol(int port, unsigned int flags)
 		else
 			v |= MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask used */
 #endif
+#ifdef CONFIG_MX53
+		if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+			v &= ~MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is used */
+		else
+			v |= MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is not used */
+#endif
 
 		__raw_writel(v, usbother_base + MXC_USBH2CTRL_OFFSET);
 		break;
+#ifdef CONFIG_MX53
+	case 3: /* Host 3 ULPI */
+		v = __raw_readl(usbother_base + MXC_USBH3CTRL_OFFSET);
+		if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+			v &= ~MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is used */
+		else
+			v |= MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is not used */
+
+		__raw_writel(v, usbother_base + MXC_USBH3CTRL_OFFSET);
+		break;
+#endif
 	}
 
 	return ret;