[U-Boot] [PATCH v2] odroid-XU3: Add entry for DTS EHCI GPIO

[Kevin Hilman <khilman@kernel.org>]

Suriyan Ramasami <suriyan.r@gmail.com> writes:

> Hello Hyungwon Hwang,
>
> On Mon, Dec 8, 2014 at 7:01 PM, Hyungwon Hwang <human.hwang@samsung.com> wrote:
>> Dear Sjoerd,
>>
>> On Fri, 05 Dec 2014 21:26:10 +0100
>> Sjoerd Simons <sjoerd.simons@collabora.co.uk> wrote:
>>
>>> Add samsung,vbus-gpio information for the XU3. This allows the usage
>>> of the EHCI controller on the XU3, which is connected to the SMSC
>>> LAN9514 chip (usb hub + network).
>>>
>>> Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
>>> ---
>>> Changes since v1:
>>>   + Correct gpio number
>>>   + Add USB configuration in the odroid XU3 default config
>>>
>>> Hyungwon could you add this one to your XU3 patchset if you send a
>>> next version (assuming it looks good)?
>>>
>>
>> Does it work only with this patch? I applied this patch on top of my
>> patchset, and connected the ethernet cable to the device. But it
>> seemed not working. Is there anything else that I should do for test?
>>
>>> For usb storage/network support this patch should be combined
>>> with the exynos configuration tweaks patch i submited earlier to the
>>> list: Exynos: Move down common USB configuration
>>>
>>>  arch/arm/dts/exynos5422-odroidxu3.dts | 4 ++++
>>>  include/configs/odroid_xu3.h          | 4 ++++
>>>  2 files changed, 8 insertions(+)
>>>
>>> diff --git a/arch/arm/dts/exynos5422-odroidxu3.dts
>>> b/arch/arm/dts/exynos5422-odroidxu3.dts index cff32a9..79a7acd 100644
>>> --- a/arch/arm/dts/exynos5422-odroidxu3.dts
>>> +++ b/arch/arm/dts/exynos5422-odroidxu3.dts
>>> @@ -31,6 +31,10 @@
>>>                       0xb0000000 0xea00000>;
>>>       };
>>>
>>> +     ehci at 12110000 {
>>> +             samsung,vbus-gpio = <&gpio 0x66 0>; /* X26 */
>>> +     };
>>> +
>>>       serial at 12C20000 {
>>>               status="okay";
>>>       };
>>> diff --git a/include/configs/odroid_xu3.h
>>> b/include/configs/odroid_xu3.h index 88bb98d..aa0c142 100644
>>> --- a/include/configs/odroid_xu3.h
>>> +++ b/include/configs/odroid_xu3.h
>>> @@ -47,6 +47,10 @@
>>>
>>>  #define
>>> CONFIG_DEFAULT_CONSOLE                "console=ttySAC2,115200n8\0"
>>> +/* USB */
>>> +#define CONFIG_USB_EHCI
>>> +#define CONFIG_USB_EHCI_EXYNOS
>>> +
>>>  /* FIXME: MUST BE REMOVED AFTER TMU IS TURNED ON */
>>>  #undef CONFIG_EXYNOS_TMU
>>>  #undef CONFIG_TMU_CMD_DTT
>>
>
> In odroid_xu3.h you might want to add the below as well (for LAN + USB storage)
>
> +/* Enable USB */
> +#define CONFIG_CMD_USB
> +#define CONFIG_USB_EHCI
> +#define CONFIG_USB_EHCI_EXYNOS
> +#define CONFIG_USB_STORAGE
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_USB_HOST_ETHER
> +#define CONFIG_USB_ETHER_SMSC95XX

+1

I enabled these locally on v10 so that I could DHCP and TFTP boot.

Kevin