[U-Boot] Question: issues for usb keyboard work with OHCI HCD

["Benoît Thébaudeau" <benoit.thebaudeau@advansee.com>]

Hi Marek,

On Tuesday, May 14, 2013 4:13:33 AM, Marek Vasut wrote:
> Dear Bo Shen,
> 
> > Hi Marek,
> > 
> > On 5/13/2013 23:12, Marek Vasut wrote:
> > > Dear Bo Shen,
> > > 
> > >> Hi All,
> > >> 
> > >> On 5/6/2013 11:01, Bo Shen wrote:
> > >>> Hi Marek,
> > >>> 
> > >>> On 5/3/2013 21:40, Marek Vasut wrote:
> > >>>> Dear Bo Shen,
> > >>>> 
> > >>>>> Hi All,
> > >>>>> 
> > >>>>>      Now, I test usb host support with Atmel boards, for example,
> > >>>>> 
> > >>>>> at91sam9x5ek board.
> > >>>>> 
> > >>>>>      When test OHCI USB host with usb keyboard. I meet the following
> > >>>>> 
> > >>>>> issue.
> > >>>>> --->8---
> > >>>>> U-Boot 2013.04-dirty (May 03 2013 - 11:00:34)
> > >>>>> 
> > >>>>> CPU: AT91SAM9G35
> > >>>>> Crystal frequency:       12 MHz
> > >>>>> CPU clock        :      400 MHz
> > >>>>> Master clock     :  133.333 MHz
> > >>>>> DRAM:  128 MiB
> > >>>>> WARNING: Caches not enabled
> > >>>>> NAND:  256 MiB
> > >>>>> MMC:   mci: 0
> > >>>>> In:    serial
> > >>>>> Out:   serial
> > >>>>> Err:   serial
> > >>>>> Net:   macb0
> > >>>>> Hit any key to stop autoboot:  0
> > >>>>> U-Boot> usb start
> > >>>>> (Re)start USB...
> > >>>>> USB0:   scanning bus 0 for devices... 2 USB Device(s) found
> > >>>>> 
> > >>>>>           scanning usb for storage devices... 0 Storage Device(s)
> > >>>>>           found
> > >>>>> 
> > >>>>> U-Boot> setenv stdin usbkbd
> > >>>>> U-Boot> ERROR: sohci_submit_job: ENOMEM
> > >>>>> ERROR: sohci_submit_job failed
> > >>>>> ... ...
> > >>>>> (repeat to print these two error line)
> > >>>> 
> > >>>> So the USB subsystem is leaking memory? Or do you only have too small
> > >>>> MALLOC
> > >>>> area?
> > >>> 
> > >>> I am not sure whether USB subsystem is leaking memory. I am digging it.
> > >>> 
> > >>> This issue is not relative with MALLOC area.
> > >>> This issue come out when all ptd[i].usb_dev (the maximum value of i is
> > >>> 64) is not NULL. Each time to call td_alloc, it will check whether
> > >>> ptd[i].usb_dev is NULL (i from 0 to 63), if not find one of
> > >>> ptd[i].usb_dev is NULL, then report ENOMEM.
> > >> 
> > >> All clue for this issue?
> > > 
> > > I assume you mean the TDs are all used up then? Are they not free'd ?
> > 
> > Yes, that's true, all TDs are used. Nowhere free them, so I use
> > urb_free_priv() to free urb in sohci_return_job() instead of
> > td_submit_job(), then it works well.
> 
> Benoit, you were the last one to plumb in it, right?

No. That was for EHCI, not OHCI.

Best regards,
Beno?t