[U-Boot-Users] [PATCH] PXA27x USB (new) OHCI support

[U-Boot-Users] [PATCH] PXA27x USB (new) OHCI support

[Rodolfo Giometti]

PXA: pxa27x USB OHCI support

Signed-off-by: Rodolfo Giometti <giometti@linux.it>

---
-------------- next part --------------
diff --git a/README b/README
index 8affdd3..7c1c88e 100644
--- a/README
+++ b/README
@@ -248,6 +248,7 @@ The following options need to be configu
 		CONFIG_SA1110
 		CONFIG_ARM7
 		CONFIG_PXA250
+		CONFIG_PXA27X
 		CONFIG_CPU_MONAHANS
 
 		MicroBlaze based CPUs:
diff --git a/cpu/pxa/usb.c b/cpu/pxa/usb.c
index 5d273cb..4ef3ac7 100644
--- a/cpu/pxa/usb.c
+++ b/cpu/pxa/usb.c
@@ -24,15 +24,21 @@
 #include <common.h>
 
 #if defined(CONFIG_USB_OHCI_NEW) && defined(CFG_USB_OHCI_CPU_INIT)
-# ifdef CONFIG_CPU_MONAHANS
+# if defined(CONFIG_CPU_MONAHANS) || defined(CONFIG_PXA27X)
 
 #include <asm/arch/pxa-regs.h>
 
 int usb_cpu_init()
 {
+#if defined(CONFIG_CPU_MONAHANS)
 	/* Enable USB host clock. */
 	CKENA |= (CKENA_2_USBHOST |  CKENA_20_UDC);
 	udelay(100);
+#endif
+#if defined(CONFIG_PXA27X)
+	/* Enable USB host clock. */
+	CKEN |= CKEN10_USBHOST;
+#endif
 
 	/* Configure Port 2 for Host (USB Client Registers) */
 	UP2OCR = 0x3000c;
@@ -55,7 +61,12 @@ #if 0
 	UHCHR |= UHCHR_PSPL; /* USBHPWR is active low */
 #endif
 
+#if defined(CONFIG_CPU_MONAHANS)
 	UHCHR &= ~UHCHR_SSEP0;
+#endif
+#if defined(CONFIG_PXA27X)
+	UHCHR &= ~UHCHR_SSEP2;
+#endif
 	UHCHR &= ~UHCHR_SSEP1;
 	UHCHR &= ~UHCHR_SSE;
 
@@ -74,5 +85,5 @@ int usb_cpu_init_fail()
 	return 0;
 }
 
-# endif /* CONFIG_CPU_MONAHANS */
+# endif /* defined(CONFIG_CPU_MONAHANS) || defined(CONFIG_PXA27X) */
 #endif /* defined(CONFIG_USB_OHCI) && defined(CFG_USB_OHCI_CPU_INIT) */

[U-Boot-Users] [PATCH] PXA27x USB (new) OHCI support

[Rodolfo Giometti]

Hello,

I think also that the following settings should be implemented into
platform specific code. That's why my patch:

diff --git a/cpu/pxa/usb.c b/cpu/pxa/usb.c
index 4ef3ac7..cfe82b9 100644
--- a/cpu/pxa/usb.c
+++ b/cpu/pxa/usb.c
@@ -40,9 +40,6 @@ int usb_cpu_init()
        CKEN |= CKEN10_USBHOST;
 #endif
 
-       /* Configure Port 2 for Host (USB Client Registers) */
-       UP2OCR = 0x3000c;
-
 #if 0
        GPIO2_2 = 0x801; /* USBHPEN - Alt. Fkt. 1 */
        GPIO3_2 = 0x801; /* USBHPWR - Alt. Fkt. 1 */


Ciao,

Rodolfo

-- 

GNU/Linux Solutions                  e-mail:    giometti at enneenne.com
Linux Device Driver                             giometti at gnudd.com
Embedded Systems                     		giometti at linux.it
UNIX programming                     phone:     +39 349 2432127

[U-Boot-Users] [PATCH] PXA27x USB (new) OHCI support

[Markus Klotzbücher]

Hi Peter,

Rodolfo Giometti <giometti@enneenne.com> writes:

> PXA: pxa27x USB OHCI support

I think this patch is more USB than ARM specific. If you agree, I'll
take care it.

Regards

	Markus

--
DENX Software Engineering GmbH, HRB 165235 Munich, CEO: Wolfgang Denk
Office:  Kirchenstr. 5,       D-82194 Groebenzell,            Germany

[U-Boot-Users] [PATCH] PXA27x USB (new) OHCI support

[Markus Klotzbücher]

Rodolfo Giometti <giometti@enneenne.com> writes:

> PXA: pxa27x USB OHCI support
>
> Signed-off-by: Rodolfo Giometti <giometti@linux.it>

Applied to U-Boot custodian repository, thanks.

Best regards

Markus Klotzbuecher

--
DENX Software Engineering GmbH, HRB 165235 Munich, CEO: Wolfgang Denk
Office:  Kirchenstr. 5,       D-82194 Groebenzell,            Germany

[U-Boot-Users] [PATCH] PXA27x USB (new) OHCI support

[Markus Klotzbücher]

Dear Rodolfo,

Rodolfo Giometti <giometti@enneenne.com> writes:

> I think also that the following settings should be implemented into
> platform specific code. That's why my patch:

Yes, you're right, I added #defines to make it Monahans specific.

Best regards

	Markus

--
DENX Software Engineering GmbH, HRB 165235 Munich, CEO: Wolfgang Denk
Office:  Kirchenstr. 5,       D-82194 Groebenzell,            Germany