From: Jon Loeliger <jdl@jdl.com>
To: u-boot@lists.denx.de
Subject: [U-Boot-Users] [PATCH 19/25] include/configs: Use new CONFIG_CMD_* in various n* named board config files.
Date: Wed, 04 Jul 2007 22:33:07 -0500 [thread overview]
Message-ID: <E1I6I5b-0008Md-Ep@jdl.com> (raw)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
---
include/configs/netstar.h | 48 ++++++++++++++++--------------------------
include/configs/ns9750dev.h | 40 +++++++++++------------------------
2 files changed, 31 insertions(+), 57 deletions(-)
diff --git a/include/configs/netstar.h b/include/configs/netstar.h
index 697796a..603c9b8 100644
--- a/include/configs/netstar.h
+++ b/include/configs/netstar.h
@@ -140,43 +140,31 @@
#define MTDIDS_DEFAULT "nor0=omapflash.0,nand0=omapnand.0"
#define MTDPARTS_DEFAULT "mtdparts=omapflash.0:8k at 16k(env),8k(r_env),448k at 576k(u-boot);omapnand.0:48M(rootfs0),48M(rootfs1),-(data)"
-#if 0
-#define CONFIG_COMMANDS (CFG_CMD_BDI | \
- CFG_CMD_BOOTD | \
- CFG_CMD_DHCP | \
- CFG_CMD_ENV | \
- CFG_CMD_FLASH | \
- CFG_CMD_IMI | \
- CFG_CMD_LOADB | \
- CFG_CMD_NET | \
- CFG_CMD_MEMORY | \
- CFG_CMD_PING | \
- CFG_CMD_RUN)
-#else
-#define CONFIG_COMMANDS (CFG_CMD_BDI | \
- CFG_CMD_BOOTD | \
- CFG_CMD_DHCP | \
- CFG_CMD_ENV | \
- CFG_CMD_FLASH | \
- CFG_CMD_NAND | \
- CFG_CMD_IMI | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_LOADB | \
- CFG_CMD_NET | \
- CFG_CMD_MEMORY | \
- CFG_CMD_PING | \
- CFG_CMD_RUN)
+/*
+ * Command line configuration.
+ */
+
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_RUN
+
#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
-#endif
#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
#define CONFIG_LOOPW
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow to break in always */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
diff --git a/include/configs/ns9750dev.h b/include/configs/ns9750dev.h
index 0b1541d..e1806a7 100644
--- a/include/configs/ns9750dev.h
+++ b/include/configs/ns9750dev.h
@@ -69,33 +69,19 @@
#define CONFIG_BAUDRATE 38400
-/***********************************************************
- * Command definition
- ***********************************************************/
-#if 0 /* @TODO */
-#define CONFIG_COMMANDS \
- (CONFIG_CMD_DFL | \
- CFG_CMD_CACHE | \
- /*CFG_CMD_NAND |*/ \
- /*CFG_CMD_EEPROM |*/ \
- /*CFG_CMD_I2C |*/ \
- /*CFG_CMD_USB |*/ \
- CFG_CMD_REGINFO | \
- CFG_CMD_DATE | \
- CFG_CMD_ELF)
-#else
-#define CONFIG_COMMANDS \
- (CONFIG_CMD_BDI | \
- CFG_CMD_NET | \
- CFG_CMD_PING | \
- CFG_CMD_CONSOLE | \
- CFG_CMD_LOADB | \
- CFG_CMD_LOADS | \
- CFG_CMD_MEMORY)
-#endif
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_CONSOLE
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+
#define CONFIG_BOOTDELAY 3
/*#define CONFIG_BOOTARGS "root=ramfs devfs=mount console=ttySA0,9600" */
@@ -108,7 +94,7 @@
/*#define CONFIG_BOOTFILE "elinos-lart" */
/*#define CONFIG_BOOTCOMMAND "tftp; bootm" */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
/* what's this ? it's not used anywhere */
#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
--
1.5.2.2.249.g45fd
reply other threads:[~2007-07-05 3:33 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=E1I6I5b-0008Md-Ep@jdl.com \
--to=jdl@jdl.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox