From: Albert ARIBAUD <albert.u.boot@aribaud.net>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 6/7] arm: ls102xa: Add SD boot support for LS1021AQDS board
Date: Thu, 18 Sep 2014 13:20:42 +0200 [thread overview]
Message-ID: <E1XUZlT-0002q6-QZ@janus> (raw)
In-Reply-To: <1411019239-12360-7-git-send-email-b18965@freescale.com>
Hi Alison,
On Thu, 18 Sep 2014 13:47:18 +0800, Alison Wang <b18965@freescale.com>
wrote:
> This patch adds SD boot support for LS1021AQDS board. SPL
> framework is used. PBL initialize the internal RAM and copy
> SPL to it, then SPL initialize DDR using SPD and copy u-boot
> from SD card to DDR, finally SPL transfer control to u-boot.
>
> Signed-off-by: Alison Wang <alison.wang@freescale.com>
> Signed-off-by: Jason Jin <jason.jin@freescale.com>
> ---
> arch/arm/cpu/armv7/ls102xa/Makefile | 1 +
> arch/arm/cpu/armv7/ls102xa/spl.c | 35 +++++++++++
> arch/arm/cpu/armv7/ls102xa/u-boot-spl.lds | 89 +++++++++++++++++++++++++++
> arch/arm/include/asm/arch-ls102xa/spl.h | 20 ++++++
> board/freescale/ls1021aqds/MAINTAINERS | 1 +
> board/freescale/ls1021aqds/ddr.c | 5 +-
> board/freescale/ls1021aqds/ls1021aqds.c | 31 ++++++++++
> board/freescale/ls1021aqds/ls102xa_pbi.cfg | 8 +++
> board/freescale/ls1021aqds/ls102xa_rcw_sd.cfg | 14 +++++
> configs/ls1021aqds_sdcard_defconfig | 4 ++
> include/configs/ls1021aqds.h | 67 ++++++++++++++++++++
> 11 files changed, 274 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/cpu/armv7/ls102xa/spl.c
> create mode 100644 arch/arm/cpu/armv7/ls102xa/u-boot-spl.lds
> create mode 100644 arch/arm/include/asm/arch-ls102xa/spl.h
> create mode 100644 board/freescale/ls1021aqds/ls102xa_pbi.cfg
> create mode 100644 board/freescale/ls1021aqds/ls102xa_rcw_sd.cfg
> create mode 100644 configs/ls1021aqds_sdcard_defconfig
>
> diff --git a/arch/arm/cpu/armv7/ls102xa/Makefile b/arch/arm/cpu/armv7/ls102xa/Makefile
> index d82ce8d..56ef3a7 100644
> --- a/arch/arm/cpu/armv7/ls102xa/Makefile
> +++ b/arch/arm/cpu/armv7/ls102xa/Makefile
> @@ -10,3 +10,4 @@ obj-y += timer.o
>
> obj-$(CONFIG_OF_LIBFDT) += fdt.o
> obj-$(CONFIG_SYS_HAS_SERDES) += fsl_ls1_serdes.o ls102xa_serdes.o
> +obj-$(CONFIG_SPL) += spl.o
> diff --git a/arch/arm/cpu/armv7/ls102xa/spl.c b/arch/arm/cpu/armv7/ls102xa/spl.c
> new file mode 100644
> index 0000000..77ea1ee
> --- /dev/null
> +++ b/arch/arm/cpu/armv7/ls102xa/spl.c
> @@ -0,0 +1,35 @@
> +/*
> + * Copyright 2014 Freescale Semiconductor, Inc.
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <spl.h>
> +
> +u32 spl_boot_device(void)
> +{
> +#ifdef CONFIG_SPL_MMC_SUPPORT
> + return BOOT_DEVICE_MMC1;
> +#endif
> + return BOOT_DEVICE_NAND;
> +}
> +
> +u32 spl_boot_mode(void)
> +{
> + switch (spl_boot_device()) {
> + case BOOT_DEVICE_MMC1:
> +#ifdef CONFIG_SPL_FAT_SUPPORT
> + return MMCSD_MODE_FAT;
> +#else
> + return MMCSD_MODE_RAW;
> +#endif
> + break;
> + case BOOT_DEVICE_NAND:
> + return 0;
> + break;
> + default:
> + puts("spl: error: unsupported device\n");
> + hang();
> + }
> +}
> diff --git a/arch/arm/cpu/armv7/ls102xa/u-boot-spl.lds b/arch/arm/cpu/armv7/ls102xa/u-boot-spl.lds
> new file mode 100644
> index 0000000..10671e7
> --- /dev/null
> +++ b/arch/arm/cpu/armv7/ls102xa/u-boot-spl.lds
> @@ -0,0 +1,89 @@
> +/*
> + * Copyright (c) 2004-2008 Texas Instruments
> + *
> + * (C) Copyright 2002
> + * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
> + *
> + * Copyright 2014 Freescale Semiconductor, Inc.
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
> +OUTPUT_ARCH(arm)
> +ENTRY(_start)
> +SECTIONS
> +{
> + . = 0x00000000;
> +
> + . = ALIGN(4);
> + .text :
> + {
> + __image_copy_start = .;
> + *(.vectors)
> + CPUDIR/start.o (.text*)
> + *(.text*)
> + }
> +
> + . = ALIGN(4);
> + .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
> +
> + . = ALIGN(4);
> + .data : {
> + *(.data*)
> + }
> +
> + . = ALIGN(4);
> + .u_boot_list : {
> + KEEP(*(SORT(.u_boot_list*_i2c_*)));
> + }
IS this required? And if it is, could it not be added to the
arch/arm/cpu/u-boot-spl.lds file? This way you would not need an .lds
file at all.
> + . = .;
> +
> + __image_copy_end = .;
> +
> + .rel.dyn : {
> + __rel_dyn_start = .;
> + *(.rel*)
> + __rel_dyn_end = .;
> + }
> +
> + .end :
> + {
> + *(.__end)
> + }
> +
> + _image_binary_end = .;
> +
> + .bss __rel_dyn_start (OVERLAY) : {
> + __bss_start = .;
> + *(.bss*)
> + . = ALIGN(4);
> + __bss_end = .;
> + }
> +
> + .dynsym _image_binary_end : { *(.dynsym) }
> + .dynbss : { *(.dynbss) }
> + .dynstr : { *(.dynstr*) }
> + .dynamic : { *(.dynamic*) }
> + .hash : { *(.hash*) }
> + .plt : { *(.plt*) }
> + .interp : { *(.interp*) }
> + .gnu : { *(.gnu*) }
> + .ARM.exidx : { *(.ARM.exidx*) }
> +}
> +
> +#if defined(CONFIG_SPL_MAX_SIZE)
> +ASSERT(__image_copy_end - __image_copy_start < (CONFIG_SPL_MAX_SIZE), \
> + "SPL image too big");
> +#endif
> +
> +#if defined(CONFIG_SPL_BSS_MAX_SIZE)
> +ASSERT(__bss_end - __bss_start < (CONFIG_SPL_BSS_MAX_SIZE), \
> + "SPL image BSS too big");
> +#endif
> +
> +#if defined(CONFIG_SPL_MAX_FOOTPRINT)
> +ASSERT(__bss_end - _start < (CONFIG_SPL_MAX_FOOTPRINT), \
> + "SPL image plus BSS too big");
> +#endif
> diff --git a/arch/arm/include/asm/arch-ls102xa/spl.h b/arch/arm/include/asm/arch-ls102xa/spl.h
> new file mode 100644
> index 0000000..26e4ea1
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-ls102xa/spl.h
> @@ -0,0 +1,20 @@
> +/*
> + * Copyright 2014 Freescale Semiconductor, Inc.
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __ASM_ARCH_SPL_H__
> +#define __ASM_ARCH_SPL_H__
> +
> +#define BOOT_DEVICE_NONE 0
> +#define BOOT_DEVICE_XIP 1
> +#define BOOT_DEVICE_XIPWAIT 2
> +#define BOOT_DEVICE_NAND 3
> +#define BOOT_DEVICE_ONENAND 4
> +#define BOOT_DEVICE_MMC1 5
> +#define BOOT_DEVICE_MMC2 6
> +#define BOOT_DEVICE_MMC2_2 7
> +#define BOOT_DEVICE_SPI 10
> +
> +#endif /* __ASM_ARCH_SPL_H__ */
> diff --git a/board/freescale/ls1021aqds/MAINTAINERS b/board/freescale/ls1021aqds/MAINTAINERS
> index 021d82b..9244057 100644
> --- a/board/freescale/ls1021aqds/MAINTAINERS
> +++ b/board/freescale/ls1021aqds/MAINTAINERS
> @@ -4,3 +4,4 @@ S: Maintained
> F: board/freescale/ls1021aqds/
> F: include/configs/ls1021aqds.h
> F: configs/ls1021aqds_nor_defconfig
> +F: configs/ls1021aqds_sdcard_defconfig
> diff --git a/board/freescale/ls1021aqds/ddr.c b/board/freescale/ls1021aqds/ddr.c
> index 679c654..369088e 100644
> --- a/board/freescale/ls1021aqds/ddr.c
> +++ b/board/freescale/ls1021aqds/ddr.c
> @@ -146,9 +146,12 @@ phys_size_t initdram(int board_type)
> {
> phys_size_t dram_size;
>
> +#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_SPL)
> puts("Initializing DDR....using SPD\n");
> dram_size = fsl_ddr_sdram();
> -
> +#else
> + dram_size = fsl_ddr_sdram_size();
> +#endif
> return dram_size;
> }
>
> diff --git a/board/freescale/ls1021aqds/ls1021aqds.c b/board/freescale/ls1021aqds/ls1021aqds.c
> index 12e83f7..85a53c9 100644
> --- a/board/freescale/ls1021aqds/ls1021aqds.c
> +++ b/board/freescale/ls1021aqds/ls1021aqds.c
> @@ -13,6 +13,7 @@
> #include <mmc.h>
> #include <fsl_esdhc.h>
> #include <fsl_ifc.h>
> +#include <spl.h>
>
> #include "../common/qixis.h"
> #include "ls1021aqds_qixis.h"
> @@ -29,10 +30,13 @@ enum {
> int checkboard(void)
> {
> char buf[64];
> +#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
> u8 sw;
> +#endif
>
> puts("Board: LS1021AQDS\n");
>
> +#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
> sw = QIXIS_READ(brdcfg[0]);
> sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
>
> @@ -46,6 +50,7 @@ int checkboard(void)
> printf("IFCCard\n");
> else
> printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
> +#endif
>
> printf("Sys ID:0x%02x, Sys Ver: 0x%02x\n",
> QIXIS_READ(id), QIXIS_READ(arch));
> @@ -155,6 +160,32 @@ int board_early_init_f(void)
> return 0;
> }
>
> +#ifdef CONFIG_SPL_BUILD
> +void board_init_f(ulong dummy)
> +{
> + struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR;
> +
> + /* Set global data pointer */
> + gd = &gdata;
> +
> + /* Clear the BSS */
> + memset(__bss_start, 0, __bss_end - __bss_start);
> +
> + get_clocks();
> +
> + preloader_console_init();
> +
> +#ifdef CONFIG_SPL_I2C_SUPPORT
> + i2c_init_all();
> +#endif
> + out_le32(&cci->ctrl_ord, CCI400_CTRLORD_TERM_BARRIER);
> +
> + dram_init();
> +
> + board_init_r(NULL, 0);
> +}
> +#endif
> +
> int config_board_mux(int ctrl_type)
> {
> u8 reg12;
> diff --git a/board/freescale/ls1021aqds/ls102xa_pbi.cfg b/board/freescale/ls1021aqds/ls102xa_pbi.cfg
> new file mode 100644
> index 0000000..edf9f94
> --- /dev/null
> +++ b/board/freescale/ls1021aqds/ls102xa_pbi.cfg
> @@ -0,0 +1,8 @@
> +#PBI commands
> +
> +#Configure Scratch register
> +09ee0200 10000000
> +#Configure alternate space
> +09570158 00080000
> +#Flush PBL data
> +096100c0 000FFFFF
> diff --git a/board/freescale/ls1021aqds/ls102xa_rcw_sd.cfg b/board/freescale/ls1021aqds/ls102xa_rcw_sd.cfg
> new file mode 100644
> index 0000000..e05ec16
> --- /dev/null
> +++ b/board/freescale/ls1021aqds/ls102xa_rcw_sd.cfg
> @@ -0,0 +1,14 @@
> +#PBL preamble and RCW header
> +aa55aa55 01ee0100
> +
> +#enable IFC, disable QSPI and DSPI
> +#0608000a 00000000 00000000 00000000
> +#00000000 00404000 60025a00 21042000
> +#00200000 00000000 00000000 01038000
> +#00000000 001b1200 00000000 00000000
> +
> +#disable IFC, enable QSPI and DSPI
> +0608000a 00000000 00000000 00000000
> +60000000 00407900 e0025a00 21046000
> +00000000 00000000 00000000 00038000
> +20024800 001b7200 00000000 00000000
> diff --git a/configs/ls1021aqds_sdcard_defconfig b/configs/ls1021aqds_sdcard_defconfig
> new file mode 100644
> index 0000000..e03c3b4
> --- /dev/null
> +++ b/configs/ls1021aqds_sdcard_defconfig
> @@ -0,0 +1,4 @@
> +CONFIG_SPL=y
> +CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SD_BOOT"
> ++S:CONFIG_ARM=y
> ++S:CONFIG_TARGET_LS1021AQDS=y
> diff --git a/include/configs/ls1021aqds.h b/include/configs/ls1021aqds.h
> index 657e3b6..440c118 100644
> --- a/include/configs/ls1021aqds.h
> +++ b/include/configs/ls1021aqds.h
> @@ -37,8 +37,48 @@ unsigned long get_board_sys_clk(void);
> unsigned long get_board_ddr_clk(void);
> #endif
>
> +#if defined(CONFIG_SD_BOOT) || defined(CONFIG_QSPI_BOOT)
> +#define CONFIG_SYS_CLK_FREQ 100000000
> +#define CONFIG_DDR_CLK_FREQ 100000000
> +#define CONFIG_QIXIS_I2C_ACCESS
> +#else
> #define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
> #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
> +#endif
> +
> +#ifdef CONFIG_RAMBOOT_PBL
> +#define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1021aqds/ls102xa_pbi.cfg
> +#endif
> +
> +#ifdef CONFIG_SD_BOOT
> +#define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1021aqds/ls102xa_rcw_sd.cfg
> +#define CONFIG_SPL_PBL_PAD
> +#define CONFIG_SPL_FRAMEWORK
> +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/ls102xa/u-boot-spl.lds"
> +#define CONFIG_SPL_LIBCOMMON_SUPPORT
> +#define CONFIG_SPL_LIBGENERIC_SUPPORT
> +#define CONFIG_SPL_ENV_SUPPORT
> +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
> +#define CONFIG_SPL_I2C_SUPPORT
> +#define CONFIG_SPL_WATCHDOG_SUPPORT
> +#define CONFIG_SPL_SERIAL_SUPPORT
> +#define CONFIG_SPL_MMC_SUPPORT
> +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0xe8
> +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
> +
> +#define CONFIG_SPL_TEXT_BASE 0x10000000
> +#define CONFIG_SPL_MAX_SIZE 0x1a000
> +#define CONFIG_SPL_STACK 0x1001d000
> +#define CONFIG_SPL_PAD_TO 0x1c000
> +#define CONFIG_SYS_TEXT_BASE 0x82000000
> +
> +#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
> +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
> +#define CONFIG_SPL_BSS_START_ADDR 0x80100000
> +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
> +#define CONFIG_SYS_MONITOR_LEN 0x80000
> +#define CONFIG_SYS_NO_FLASH
> +#endif
>
> #ifndef CONFIG_SYS_TEXT_BASE
> #define CONFIG_SYS_TEXT_BASE 0x67f80000
> @@ -70,6 +110,7 @@ unsigned long get_board_ddr_clk(void);
> /*
> * IFC Definitions
> */
> +#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
> #define CONFIG_FSL_IFC
> #define CONFIG_SYS_FLASH_BASE 0x60000000
> #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
> @@ -161,6 +202,7 @@ unsigned long get_board_ddr_clk(void);
> #define CONFIG_CMD_NAND
>
> #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
> +#endif
>
> /*
> * QIXIS Definitions
> @@ -322,7 +364,12 @@ unsigned long get_board_ddr_clk(void);
>
> #define CONFIG_CMDLINE_TAG
> #define CONFIG_CMDLINE_EDITING
> +
> +#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_QSPI_BOOT)
> #define CONFIG_CMD_IMLS
> +#else
> +#undef CONFIG_CMD_IMLS
> +#endif
>
> #define CONFIG_HWCONFIG
> #define HWCONFIG_BUFFER_SIZE 128
> @@ -370,17 +417,37 @@ unsigned long get_board_ddr_clk(void);
> #define CONFIG_SYS_INIT_SP_ADDR \
> (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
>
> +#ifdef CONFIG_SPL_BUILD
> +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
> +#else
> #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
> +#endif
>
> /*
> * Environment
> */
> #define CONFIG_ENV_OVERWRITE
>
> +#if defined(CONFIG_SD_BOOT)
> +#define CONFIG_ENV_OFFSET (1024 * 1024)
> +#define CONFIG_ENV_IS_IN_MMC
> +#define CONFIG_SYS_MMC_ENV_DEV 0
> +#define CONFIG_ENV_SIZE 0x2000
> +#elif defined(CONFIG_NAND_BOOT)
> +#define CONFIG_ENV_IS_IN_NAND
> +#define CONFIG_ENV_SIZE 0x2000
> +#define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
> +#elif defined(CONFIG_QSPI_BOOT)
> +#define CONFIG_ENV_IS_IN_SPI_FLASH
> +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
> +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
> +#define CONFIG_ENV_SECT_SIZE 0x10000
> +#else
> #define CONFIG_ENV_IS_IN_FLASH
> #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
> #define CONFIG_ENV_SIZE 0x2000
> #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
> +#endif
>
> #define CONFIG_OF_LIBFDT
> #define CONFIG_OF_BOARD_SETUP
Amicalement,
--
Albert.
next prev parent reply other threads:[~2014-09-18 11:20 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-18 5:47 [U-Boot] [PATCH 0/7] Add SD boot support for LS1021AQDS/TWR board Alison Wang
2014-09-18 5:47 ` [U-Boot] [PATCH 1/7] spl: pbl: Add new SPL image for pblimage tool Alison Wang
2014-09-18 9:37 ` Albert ARIBAUD
2014-09-19 5:07 ` Huan Wang
2014-09-20 7:47 ` Albert ARIBAUD
2014-09-22 6:17 ` Huan Wang
2014-09-22 15:49 ` York Sun
2014-09-23 2:43 ` Huan Wang
2014-09-23 3:40 ` York Sun
2014-09-25 6:33 ` Huan Wang
2014-09-18 5:47 ` [U-Boot] [PATCH 2/7] ls102xa: pblimage: Add pblimage tool support for LS102xA Alison Wang
2014-09-18 9:57 ` Albert ARIBAUD
2014-09-22 6:22 ` Huan Wang
2014-09-24 7:55 ` [U-Boot] [OT] " Albert ARIBAUD
2014-09-24 8:00 ` Huan Wang
2014-09-18 5:47 ` [U-Boot] [PATCH 3/7] spl: Use u-boot.img instead of u-boot.bin when CONFIG_SPL_PBL_PAD is enabled Alison Wang
2014-09-18 5:47 ` [U-Boot] [PATCH 4/7] ls102xa: qixis: Add CONFIG_QIXIS_I2C_ACCESS macro Alison Wang
2014-09-18 5:47 ` [U-Boot] [PATCH 5/7] common: spl: Add interactive DDR debugger support for SPL Alison Wang
2014-09-18 5:47 ` [U-Boot] [PATCH 6/7] arm: ls102xa: Add SD boot support for LS1021AQDS board Alison Wang
2014-09-18 11:20 ` Albert ARIBAUD [this message]
2014-09-19 3:40 ` Alison Wang
2014-09-19 5:10 ` Huan Wang
[not found] ` <1411053355745.66856@freescale.com>
2014-09-19 15:56 ` Albert ARIBAUD
2014-09-22 6:46 ` Huan Wang
2014-09-22 11:01 ` Albert ARIBAUD
2014-09-25 6:45 ` Huan Wang
2014-10-01 18:08 ` Albert ARIBAUD
2014-10-08 9:53 ` Huan Wang
2014-10-11 11:30 ` Albert ARIBAUD
2014-10-15 6:56 ` Huan Wang
2014-10-15 10:30 ` Albert ARIBAUD
2014-09-18 5:47 ` [U-Boot] [PATCH 7/7] arm: ls102xa: Add SD boot support for LS1021ATWR board Alison Wang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=E1XUZlT-0002q6-QZ@janus \
--to=albert.u.boot@aribaud.net \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox