[U-Boot-Users] Doubts about usage of BDI2000 !

Woodruff, Richard
2004-10-14T20:40:15Z

BDI does support ARM11. I know people who have used it in TI, You might
need to get some updated drivers though.

I'll attach what should work on the OMAP2420. I've not tried it as I've
been using Lauterbach.

Regards,
Richard W.

> -----Original Message-----
> From: u-boot-users-admin at lists.sourceforge.net [mailto:u-boot-users-
> admin at lists.sourceforge.net] On Behalf Of George G. Davis
> Sent: Thursday, October 14, 2004 3:17 PM
> To: ravi.aloor at wipro.com
> Cc: u-boot-users at lists.sourceforge.net
> Subject: Re: [U-Boot-Users] Doubts about usage of BDI2000 !
>
> On Thu, Oct 14, 2004 at 08:46:16PM +0530, ravi.aloor at wipro.com wrote:
> >
> > Hi, I am new to u-boot. I have few doubts. A brief explanation about
my
> > working environment:
> > - ARM11 based target board, having its own IP address
> > - PC running on RedHat Linux-8.0, having its own IP address
> > - BDI2000, having its own IP address
> > - PC and BDI2000 are connected to the network
> > (IP address for BDI2000 is 192.168.226.159)
> > - U-boot is already available on target board in the flash
> > memory
> > - Firmware is already available on BDI2000
> > - BDI2000 is connected to the target board through
> > - Using gdb-6.1 configured with --target=arm-linux
> >
> > The following are my doubts:
> > 1. I want to debug u-boot. So to start debugging u-boot, Do I need
to
> > use bare target board that does not contain u-boot already ?
> >
> > 2. I could not start debugging u-boot. So I started debugging kernel
> > with the target board that already contains u-boot. Please check the
> > following:
> >
> > [ravi at localhost 2.6_kernel]$ /home/ravi/gdb-6.1/temp/gdb/gdb vmlinux
> > GNU gdb 6.1
> > Copyright 2004 Free Software Foundation, Inc.
> > GDB is free software, covered by the GNU General Public License, and
you
> > are
> > welcome to change it and/or distribute copies of it under certain
> > conditions.
> > Type "show copying" to see the conditions.
> > There is absolutely no warranty for GDB. Type "show warranty" for
> > details.
> > This GDB was configured as "--host=i686-pc-linux-gnu
> > --target=arm-linux"...
> > (gdb)
> > (gdb) target remote 192.168.226.159:2001
> > 192.168.226.159:2001: Connection refused.
> > (gdb) target remote bdi:2001
> > bdi:2001: Connection refused.
>
> Based on that response, I would guess that your BDI2000 is not yet
> configured and connected to the target yet, i.e. the BDI2000 has
> not successfully detected any target CPU on the JTAG chain. Try
> using `telnet 192.168.226.159` to see what's going on with the
> BDI2000. Also, try referring to the BDI manual for help configuring
> the BDI and, of course, talk to your processor/board vendor to
> resolve BDI setup/config details. Does the BDI2000 even support ARM11
> based processors yet?
>
> --
> Regards,
> George
>
> > (gdb) quit
> > [ravi at localhost 2.6_kernel]$
> >
> > Please help me ... Thanks A Lot In Advance,
> > Ravi
> >
> >
> > -------------------------------------------------------
> > This SF.net email is sponsored by: IT Product Guide on
ITManagersJournal
> > Use IT products in your business? Tell us what you think of them.
Give
> us
> > Your Opinions, Get Free ThinkGeek Gift Certificates! Click to find
out
> more
> > http://productguide.itmanagersjournal.com/guidepromo.tmpl
> > _______________________________________________
> > U-Boot-Users mailing list
> > U-Boot-Users at lists.sourceforge.net
> > https://lists.sourceforge.net/lists/listinfo/u-boot-users
>
>
> -------------------------------------------------------
> This SF.net email is sponsored by: IT Product Guide on
ITManagersJournal
> Use IT products in your business? Tell us what you think of them. Give
us
> Your Opinions, Get Free ThinkGeek Gift Certificates! Click to find out
> more
> http://productguide.itmanagersjournal.com/guidepromo.tmpl
> _______________________________________________
> U-Boot-Users mailing list
> U-Boot-Users at lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/u-boot-users
-------------- next part --------------
A non-text attachment was scrubbed...
Name: h4-BDI-new.cfg
Type: application/octet-stream
Size: 6124 bytes
Desc: h4-BDI-new.cfg
Url : http://lists.denx.de/pipermail/u-boot/attachments/20041014/d5c97aba/attachment.obj