From: Joost van Zwieten <joost@diskos.nl>
To: Tom Rini <trini@konsulko.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>, u-boot@lists.denx.de
Subject: Re: kernel doesn't start on Odroid U2 unless setting initrd_high
Date: Wed, 11 Jan 2023 21:28:42 +0100 [thread overview]
Message-ID: <UV8COR.VZGN6AX4HY9C1@diskos.nl> (raw)
In-Reply-To: <20230110232915.GS3787616@bill-the-cat>
On Tue, Jan 10, 2023 at 18:29, Tom Rini <trini@konsulko.com> wrote:
> On Wed, Jan 11, 2023 at 12:10:42AM +0100, Joost van Zwieten wrote:
>>
>>
>> On Tue, Jan 10, 2023 at 18:08, Tom Rini <trini@konsulko.com> wrote:
>> > On Wed, Jan 11, 2023 at 12:01:46AM +0100, Joost van Zwieten wrote:
>> > >
>> > >
>> > > On Tue, Jan 10, 2023 at 13:41, Tom Rini <trini@konsulko.com>
>> wrote:
>> > > > On Tue, Jan 10, 2023 at 09:13:32AM +0100, Joost van Zwieten
>> wrote:
>> > > >
>> > > > > Dear maintainers,
>> > > > >
>> > > > > As of commit 4963f63fe61f15329d77472a762b1d8bf754d24b
>> U-Boot
>> > > fails
>> > > > > to start
>> > > > > a kernel (with `bootz`) on my Odroid U2 unless I force
>> > > > > `initrd_high`, e.g.
>> > > > > to `0x50000000`. With commit 4963f63f and `initrd_high`
>> > > *unset* I
>> > > > > get the
>> > > > > following output:
>> > > > >
>> > > > > U-Boot 2020.10-rc2-00314-g4963f63fe6 (Jan 09 2023 -
>> 23:59:31
>> > > > > +0100)
>> > > > >
>> > > > > CPU: Exynos4412 @ 1 GHz
>> > > > > Model: Odroid based on Exynos4412
>> > > > > Type: u3
>> > > > > DRAM: 2 GiB
>> > > > > LDO20@VDDQ_EMMC_1.8V: set 1800000 uV; enabling
>> > > > > LDO22@VDDQ_EMMC_2.8V: set 2800000 uV; enabling
>> > > > > LDO21@TFLASH_2.8V: set 2800000 uV; enabling
>> > > > > MMC: SAMSUNG SDHCI: 2, EXYNOS DWMMC: 0
>> > > > > Loading Environment from MMC... *** Warning - bad CRC,
>> using
>> > > > > default
>> > > > > environment
>> > > > >
>> > > > > In: serial
>> > > > > Out: serial
>> > > > > Err: serial
>> > > > > Boot device: MMC(2)
>> > > > > Net: No ethernet found.
>> > > > > Hit any key to stop autoboot: 0
>> > > > > Odroid # env set fk_kvers 5.10.0-20-armmp
>> > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
>> ${fdt_addr_r}
>> > > > > /boot/dtbs/${fk_kvers}/exynos4412-odroidu3.dtb
>> > > > > 53440 bytes read in 50 ms (1 MiB/s)
>> > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
>> > > ${kernel_addr_r}
>> > > > > /boot/vmlinuz-${fk_kvers}
>> > > > > 4973056 bytes read in 182 ms (26.1 MiB/s)
>> > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
>> > > ${ramdisk_addr_r}
>> > > > > /boot/initrd.img-${fk_kvers}
>> > > > > 22231585 bytes read in 777 ms (27.3 MiB/s)
>> > > > > Odroid # env set bootargs console=ttySAC1,115200n8
>> > > > > Odroid # bootz ${kernel_addr_r}
>> > > ${ramdisk_addr_r}:${filesize}
>> > > > > ${fdt_addr_r}
>> > > > > Kernel image @ 0x41000000 [ 0x000000 - 0x4be200 ]
>> > > > > ## Flattened Device Tree blob at 40800000
>> > > > > Booting using the fdt blob at 0x40800000
>> > > > > Loading Ramdisk to b9947000, end bae7aa21 ... OK
>> > > > > Loading Device Tree to b9936000, end b99460bf ... OK
>> > > > >
>> > > > > Starting kernel ...
>> > > > >
>> > > > > And that's all I ever see. Normally the initrd loads a
>> module
>> > > that
>> > > > > causes an
>> > > > > LED on the Odroid to blink, and this is not happening
>> either,
>> > > so
>> > > > > I'm pretty
>> > > > > confident the kernel doesn't start or at least crashes
>> before
>> > > > > producing
>> > > > > output. If I set `initrd_high` to `0x50000000` (or
>> something
>> > > in the
>> > > > > neighborhood) the kernel starts just fine:
>> > > > >
>> > > > > U-Boot 2020.10-rc2-00314-g4963f63fe6 (Jan 09 2023 -
>> 23:59:31
>> > > > > +0100)
>> > > > >
>> > > > > CPU: Exynos4412 @ 1 GHz
>> > > > > Model: Odroid based on Exynos4412
>> > > > > Type: u3
>> > > > > DRAM: 2 GiB
>> > > > > LDO20@VDDQ_EMMC_1.8V: set 1800000 uV; enabling
>> > > > > LDO22@VDDQ_EMMC_2.8V: set 2800000 uV; enabling
>> > > > > LDO21@TFLASH_2.8V: set 2800000 uV; enabling
>> > > > > MMC: SAMSUNG SDHCI: 2, EXYNOS DWMMC: 0
>> > > > > Loading Environment from MMC... *** Warning - bad CRC,
>> using
>> > > > > default
>> > > > > environment
>> > > > >
>> > > > > In: serial
>> > > > > Out: serial
>> > > > > Err: serial
>> > > > > Boot device: MMC(2)
>> > > > > Net: No ethernet found.
>> > > > > Hit any key to stop autoboot: 0
>> > > > > Odroid # env set fk_kvers 5.10.0-20-armmp
>> > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
>> ${fdt_addr_r}
>> > > > > /boot/dtbs/${fk_kvers}/exynos4412-odroidu3.dtb
>> > > > > 53440 bytes read in 49 ms (1 MiB/s)
>> > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
>> > > ${kernel_addr_r}
>> > > > > /boot/vmlinuz-${fk_kvers}
>> > > > > 4973056 bytes read in 181 ms (26.2 MiB/s)
>> > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
>> > > ${ramdisk_addr_r}
>> > > > > /boot/initrd.img-${fk_kvers}
>> > > > > 22231585 bytes read in 777 ms (27.3 MiB/s)
>> > > > > Odroid # env set bootargs console=ttySAC1,115200n8
>> > > > > Odroid # env set initrd_high 0x50000000
>> > > > > Odroid # bootz ${kernel_addr_r}
>> > > ${ramdisk_addr_r}:${filesize}
>> > > > > ${fdt_addr_r}
>> > > > > Kernel image @ 0x41000000 [ 0x000000 - 0x4be200 ]
>> > > > > ## Flattened Device Tree blob at 40800000
>> > > > > Booting using the fdt blob at 0x40800000
>> > > > > Loading Ramdisk to 4eacc000, end 4ffffa21 ... OK
>> > > > > Loading Device Tree to bae6a000, end bae7a0bf ... OK
>> > > > >
>> > > > > Starting kernel ...
>> > > > >
>> > > > > [ 0.000000] Booting Linux on physical CPU 0xa00
>> > > > > <truncated>
>> > > > >
>> > > > > The difference between those two runs is the location
>> where
>> > > U-Boot
>> > > > > loads the
>> > > > > initrd. The parent commit of 4963f63f boots fine without
>> > > setting
>> > > > > `initrd_high`:
>> > > > >
>> > > > > U-Boot 2020.10-rc2-00313-gdfaf6a5797 (Jan 10 2023 -
>> 00:13:19
>> > > > > +0100)
>> > > > >
>> > > > > CPU: Exynos4412 @ 1 GHz
>> > > > > Model: Odroid based on Exynos4412
>> > > > > Type: u3
>> > > > > DRAM: 2 GiB
>> > > > > LDO20@VDDQ_EMMC_1.8V: set 1800000 uV; enabling
>> > > > > LDO22@VDDQ_EMMC_2.8V: set 2800000 uV; enabling
>> > > > > LDO21@TFLASH_2.8V: set 2800000 uV; enabling
>> > > > > MMC: SAMSUNG SDHCI: 2, EXYNOS DWMMC: 0
>> > > > > Loading Environment from MMC... *** Warning - bad CRC,
>> using
>> > > > > default
>> > > > > environment
>> > > > >
>> > > > > In: serial
>> > > > > Out: serial
>> > > > > Err: serial
>> > > > > Boot device: MMC(2)
>> > > > > Net: No ethernet found.
>> > > > > Hit any key to stop autoboot: 0
>> > > > > Odroid # env set fk_kvers 5.10.0-20-armmp
>> > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
>> ${fdt_addr_r}
>> > > > > /boot/dtbs/${fk_kvers}/exynos4412-odroidu3.dtb
>> > > > > 53440 bytes read in 49 ms (1 MiB/s)
>> > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
>> > > ${kernel_addr_r}
>> > > > > /boot/vmlinuz-${fk_kvers}
>> > > > > 4973056 bytes read in 181 ms (26.2 MiB/s)
>> > > > > Odroid # load mmc ${mmcbootdev}:${mmcbootpart}
>> > > ${ramdisk_addr_r}
>> > > > > /boot/initrd.img-${fk_kvers}
>> > > > > 22231585 bytes read in 776 ms (27.3 MiB/s)
>> > > > > Odroid # env set bootargs console=ttySAC1,115200n8
>> > > > > Odroid # bootz ${kernel_addr_r}
>> > > ${ramdisk_addr_r}:${filesize}
>> > > > > ${fdt_addr_r}
>> > > > > Kernel image @ 0x41000000 [ 0x000000 - 0x4be200 ]
>> > > > > ## Flattened Device Tree blob at 40800000
>> > > > > Booting using the fdt blob at 0x40800000
>> > > > > Loading Ramdisk to 4eacc000, end 4ffffa21 ... OK
>> > > > > Loading Device Tree to 4eabb000, end 4eacb0bf ... OK
>> > > > >
>> > > > > Starting kernel ...
>> > > > >
>> > > > > [ 0.000000] Booting Linux on physical CPU 0xa00
>> > > > > <truncated>
>> > > > >
>> > > > > I've tested two different kernels from Debian (buster and
>> > > bullseye)
>> > > > > and both
>> > > > > have the same problem. I'm building U-Boot using the
>> default
>> > > config
>> > > > > for
>> > > > > board `odroid` and boot the Odroid from an SD card with
>> > > firmware
>> > > > > (`bl1`,
>> > > > > `bl2` and `tzsw`) from Hardkernel's clone of the u-boot
>> > > repository
>> > > > > [1].
>> > > > > There are no peripherals connected apart from the SD card
>> and
>> > > the
>> > > > > serial
>> > > > > console. Please let me know if you need more information.
>> > > >
>> > > > Interesting. So what does "bdi" show, both in the older good
>> and
>> > > > then current tree? Specifically the information about where
>> DRAM
>> > > is, and
>> > > > how large it is? Thanks.
>> > > >
>> > > > --
>> > > > Tom
>> > >
>> > > Both 4963f63f (not working) and its parent (working) produce
>> the
>> > > same
>> > > output:
>> > >
>> > > boot_params = 0x40000100
>> > > DRAM bank = 0x00000000
>> > > -> start = 0x40000000
>> > > -> size = 0x10000000
>> > > DRAM bank = 0x00000001
>> > > -> start = 0x50000000
>> > > -> size = 0x10000000
>> > > DRAM bank = 0x00000002
>> > > -> start = 0x60000000
>> > > -> size = 0x10000000
>> > > DRAM bank = 0x00000003
>> > > -> start = 0x70000000
>> > > -> size = 0x10000000
>> > > DRAM bank = 0x00000004
>> > > -> start = 0x80000000
>> > > -> size = 0x10000000
>> > > DRAM bank = 0x00000005
>> > > -> start = 0x90000000
>> > > -> size = 0x10000000
>> > > DRAM bank = 0x00000006
>> > > -> start = 0xa0000000
>> > > -> size = 0x10000000
>> > > DRAM bank = 0x00000007
>> > > -> start = 0xb0000000
>> > > -> size = 0x0ff00000
>> > > memstart = 0x40000000
>> > > memsize = 0x7ff00000
>> > > flashstart = 0x00000000
>> > > flashsize = 0x00000000
>> > > flashoffset = 0x00000000
>> > > baudrate = 115200 bps
>> > > relocaddr = 0xbfe83000
>> > > reloc off = 0x7c083000
>> > > Build = 32-bit
>> > > current eth = unknown
>> > > ethaddr = (not set)
>> > > IP addr = <NULL>
>> > > fdt_blob = 0xbae7bf00
>> > > new_fdt = 0xbae7bf00
>> > > fdt_size = 0x00002fa0
>> > > lmb_dump_all:
>> > > memory.cnt = 0x1
>> > > memory.size = 0x0
>> > > memory.reg[0x0].base = 0x40000000
>> > > .size = 0x7ff00000
>> > >
>> > > reserved.cnt = 0x1
>> > > reserved.size = 0x0
>> > > reserved.reg[0x0].base = 0xbae7acd0
>> > > .size = 0x5085330
>> > > arch_number = 0x000010c1
>> > > TLB addr = 0xbfef0000
>> > > irq_sp = 0xbae7bef0
>> > > sp start = 0xbae7bee0
>> > > Board Type = 0
>> > > Early malloc usage: f0 / 400
>> > >
>> > > I'm not sure if this is relevant, but with the failing commit
>> I can
>> > > get the
>> > > kernel to start with `initrd_high` set to `0x70000000` or
>> lower,
>> > > but not
>> > > higher.
>> >
>> > OK, so 8 whole banks, of 256MB each. Does this platform have 2GB
>> of
>> > memory for real?
>> >
>> > --
>> > Tom
>>
>> Yes, it does. See https://www.hardkernel.com/shop/odroid-u3/ .
>
> Thanks. I guess my current thought is that in the absence of adding
> earlycon to the kernel args, to perhaps get more info out of the
> kernel
> as to when / where it's dying, that bootm_size should be set to
> 0x10000000 (256MB) to replicate the old behavior, on this platform.
> Jaehoon, do you have any other ideas?
>
> --
> Tom
I was not aware of the existence of `earlycon`. Running the first
failing commit 4963f63f with `earlycon` and with `initrd_high` *unset*
reveals a kernel panic:
Kernel image @ 0x41000000 [ 0x000000 - 0x4be200 ]
## Flattened Device Tree blob at 40800000
Booting using the fdt blob at 0x40800000
Loading Ramdisk to b9947000, end bae7aa21 ... OK
Loading Device Tree to b9936000, end b99460bf ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0xa00
[ 0.000000] Linux version 5.10.0-20-armmp
(debian-kernel@lists.debian.org) (gcc-10 (Debian 10.2.1-6) 10.2.1
20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Debian
5.10.158-2 (2022-12-13)
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7),
cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT
aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Hardkernel ODROID-U3 board
based on Exynos4412
[ 0.000000] earlycon: exynos4210 at MMIO 0x13810000 (options '')
[ 0.000000] printk: bootconsole [exynos4210] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created DMA memory pool at
0xbf700000, size 8 MiB
[ 0.000000] OF: reserved mem: initialized node region_mfc_right,
compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at
0xbd300000, size 36 MiB
[ 0.000000] OF: reserved mem: initialized node region_mfc_left,
compatible id shared-dma-pool
[ 0.000000] cma: Reserved 16 MiB at 0xbc000000
[ 0.000000] Samsung CPU ID: 0xe4412220
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem
0x0000000040000000-0x000000006fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem [mem
0x0000000070000000-0x00000000bd2fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem
0x0000000040000000-0x00000000bd2fffff]
[ 0.000000] Initmem setup node 0 [mem
0x0000000040000000-0x00000000bd2fffff]
[ 0.000000] Running under secure firmware.
[ 0.000000] 8<--- cut here ---
[ 0.000000] Unable to handle kernel paging request at virtual
address 3ae7aa15
[ 0.000000] pgd = (ptrval)
[ 0.000000] [3ae7aa15] *pgd=00000000
[ 0.000000] Internal error: Oops: 5 [#1] SMP ARM
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted
5.10.0-20-armmp #1 Debian 5.10.158-2
[ 0.000000] Hardware name: Samsung Exynos (Flattened Device Tree)
[ 0.000000] PC is at memcmp+0x24/0x48
[ 0.000000] LR is at start_kernel+0xac/0x5c4
[ 0.000000] pc : [<c07cb224>] lr : [<c1200dc0>] psr:
200000d3
[ 0.000000] sp : c1401fa0 ip : c0fba3e7 fp : c1401fac
[ 0.000000] r10: 10c5387d r9 : 3ae7aa11 r8 : c0fba3e8
[ 0.000000] r7 : 3ae7aa21 r6 : c1405e40 r5 : c15a003c r4 :
3ae7aa15
[ 0.000000] r3 : 3ae7aa14 r2 : 3ae7aa20 r1 : c0fba3e8 r0 :
3ae7aa15
[ 0.000000] Flags: nzCv IRQs off FIQs off Mode SVC_32 ISA
ARM Segment none
[ 0.000000] Control: 10c5387d Table: 4020404a DAC: 00000051
[ 0.000000] Process swapper (pid: 0, stack limit = 0x(ptrval))
[ 0.000000] Stack: (0xc1401fa0 to 0xc1402000)
[ 0.000000] 1fa0: c1401ff4 c1401fb0 c1200dc0 c07cb20c 00000000
00000000 00000000 00000000
[ 0.000000] 1fc0: 00000000 c129ae64 00000000 00000000 c12004b0
00000051 10c0387d 000010c1
[ 0.000000] 1fe0: b9936000 413fc090 00000000 c1401ff8 00000000
c1200d20 00000000 00000000
[ 0.000000] Backtrace:
[ 0.000000] [<c07cb200>] (memcmp) from [<c1200dc0>]
(start_kernel+0xac/0x5c4)
[ 0.000000] [<c1200d14>] (start_kernel) from [<00000000>] (0x0)
[ 0.000000] r9:413fc090 r8:b9936000 r7:000010c1 r6:10c0387d
r5:00000051 r4:c12004b0
[ 0.000000] Code: e2422001 e2403001 e241c001 e0802002 (e5f30001)
[ 0.000000] ---[ end trace 58996bc4bee07162 ]---
[ 0.000000] Kernel panic - not syncing: Attempted to kill the
idle task!
[ 0.000000] ---[ end Kernel panic - not syncing: Attempted to
kill the idle task! ]---
Best, Joost
next prev parent reply other threads:[~2023-01-11 20:28 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-10 8:13 kernel doesn't start on Odroid U2 unless setting initrd_high Joost van Zwieten
2023-01-10 18:41 ` Tom Rini
2023-01-10 23:01 ` Joost van Zwieten
2023-01-10 23:08 ` Tom Rini
2023-01-10 23:10 ` Joost van Zwieten
2023-01-10 23:29 ` Tom Rini
2023-01-11 20:28 ` Joost van Zwieten [this message]
2023-01-11 20:38 ` Tom Rini
2023-01-11 21:08 ` Joost van Zwieten
2023-01-12 0:10 ` Tom Rini
2023-01-12 22:32 ` Joost van Zwieten
2023-01-13 15:01 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=UV8COR.VZGN6AX4HY9C1@diskos.nl \
--to=joost@diskos.nl \
--cc=jh80.chung@samsung.com \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox