From: Tom Rini <trini@konsulko.com>
To: Sumit Garg <sumit.garg@linaro.org>
Cc: u-boot@lists.denx.de, rfried.dev@gmail.com, hs@denx.de,
joe.hershberger@ni.com, stephan@gerhold.net,
mworsfold@impinj.com, lgillham@impinj.com, jbrennan@impinj.com,
nicolas.dechesne@linaro.org, vinod.koul@linaro.org,
daniel.thompson@linaro.org
Subject: Re: [PATCH v2 07/14] net: dwc_eth_qos: Allow platform to override tx/rx_fifo_sz
Date: Fri, 10 Feb 2023 13:44:01 -0500 [thread overview]
Message-ID: <Y+aQcVL13GeSNozK@bill-the-cat> (raw)
In-Reply-To: <20230201135901.482671-8-sumit.garg@linaro.org>
[-- Attachment #1: Type: text/plain, Size: 455 bytes --]
On Wed, Feb 01, 2023 at 07:28:54PM +0530, Sumit Garg wrote:
> The GMAC controller on QCS404 SoC (support added by upcoming patch) fails
> to work with maximum tx/rx_fifo_sz supported by the hardware (16K). So
> allow platforms to override FIFO size using corresponding DT node
> properties.
>
> Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Applied to u-boot/master, thanks!
--
Tom
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 659 bytes --]
next prev parent reply other threads:[~2023-02-10 18:45 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-02-01 13:58 [PATCH v2 00/14] QCS404: Add ethernet and I2C drivers Sumit Garg
2023-02-01 13:58 ` [PATCH v2 01/14] qcs404: sysmap: Don't map reserved memory ranges Sumit Garg
2023-02-10 18:43 ` Tom Rini
2023-02-01 13:58 ` [PATCH v2 02/14] qcs404-evb: Enable msm_gpio driver support Sumit Garg
2023-02-10 18:43 ` Tom Rini
2023-02-01 13:58 ` [PATCH v2 03/14] clocks: qcs404: Add support for ethernet clocks Sumit Garg
2023-02-10 18:43 ` Tom Rini
2023-02-01 13:58 ` [PATCH v2 04/14] pinctrl: qcs404: Enable ethernet pinmux options Sumit Garg
2023-02-10 18:43 ` Tom Rini
2023-02-01 13:58 ` [PATCH v2 05/14] pinctrl-snapdragon: Get rid of custom drive-strength values Sumit Garg
2023-02-10 18:43 ` Tom Rini
2023-02-01 13:58 ` [PATCH v2 06/14] net: dwc_eth_qos: Make eqos_get_tick_clk_rate callback optional Sumit Garg
2023-02-04 0:41 ` Ramon Fried
2023-02-10 18:43 ` Tom Rini
2023-02-01 13:58 ` [PATCH v2 07/14] net: dwc_eth_qos: Allow platform to override tx/rx_fifo_sz Sumit Garg
2023-02-04 0:42 ` Ramon Fried
2023-02-10 18:44 ` Tom Rini [this message]
2023-02-01 13:58 ` [PATCH v2 08/14] net: dwc_eth_qos: Add Qcom ethernet driver glue layer Sumit Garg
2023-02-04 0:42 ` Ramon Fried
2023-02-10 18:44 ` Tom Rini
2023-02-01 13:58 ` [PATCH v2 09/14] dts: qcs404-evb: Add ethernet controller node Sumit Garg
2023-02-10 18:44 ` Tom Rini
2023-02-01 13:58 ` [PATCH v2 10/14] clock-snapdragon: Add clk_rcg_set_rate() with mnd_width=0 Sumit Garg
2023-02-10 18:44 ` Tom Rini
2023-02-01 13:58 ` [PATCH v2 12/14] pinctrl: qcs404: Enable I2C pinmux options Sumit Garg
2023-02-10 18:44 ` Tom Rini
2023-02-01 13:59 ` [PATCH v2 13/14] i2c: Add support for Qualcomm I2C driver Sumit Garg
2023-02-10 18:44 ` Tom Rini
2023-02-01 13:59 ` [PATCH v2 14/14] dts: qcs404-evb: Add I2C controller nodes Sumit Garg
2023-02-10 18:44 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Y+aQcVL13GeSNozK@bill-the-cat \
--to=trini@konsulko.com \
--cc=daniel.thompson@linaro.org \
--cc=hs@denx.de \
--cc=jbrennan@impinj.com \
--cc=joe.hershberger@ni.com \
--cc=lgillham@impinj.com \
--cc=mworsfold@impinj.com \
--cc=nicolas.dechesne@linaro.org \
--cc=rfried.dev@gmail.com \
--cc=stephan@gerhold.net \
--cc=sumit.garg@linaro.org \
--cc=u-boot@lists.denx.de \
--cc=vinod.koul@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox