* [PATCH v3 00/76] Clean up of bad Kconfig options
@ 2023-02-01 20:19 Simon Glass
2023-02-01 20:19 ` [PATCH v3 01/76] moveconfig: Add an option to compare Kconfig against source Simon Glass
` (72 more replies)
0 siblings, 73 replies; 87+ messages in thread
From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw)
To: u-boot
Cc: Tom Rini, Simon Glass, Alexey Brodkin, Alison Wang,
Anatolij Gustschin, Andreas Bießmann, Andy Fleming,
Angelo Dureghello, Joe Hershberger, Kever Yang, Marek Vasut,
Mario Six, Minkyu Kang, Nobuhiro Iwamatsu, Philipp Tomsich,
Priyanka Jain, Stefan Roese, Stefano Babic, Wolfgang Denk
This series adds source scanning to moveconfig.py so that it can look for
Kconfig options mentioned in the source which do not appear in Kconfig,
and vice versa.
This tool is then used to clean up the unused or obsolete options
mentioned in Makefiles, along with any attached source code.
No functional change is intended.
This should make it easier to move to the new kconfig approach.
Changes in v3:
- Update to support lower case CONFIG options
- Drop efi_loader change
- Drop the 10 patches that rename lower-case Kconfig options
Changes in v2:
- Just drop the reference
- Reinstate usb_hub code removed by accident
- Drop patch "treewide: Correct invalid Kconfig syntax and warnings"
Simon Glass (76):
moveconfig: Add an option to compare Kconfig against source
power: Drop fg_max77693
nand: Drop CONFIG_NAND_SPEAR
power: Drop pmic_max77693.c
gpio: Drop adi_gpio2
Makefile: Drop CONFIG_AIS_CONFIG_FILE
misc: Drop ali512x
sandbox: Drop reference to CONFIG_ARCH_DEVICE_TREE
arm: mvebu: Remove reference to ARMADA_370
arm: mvebu: Drop reference to CONFIG_ARMADA_39X
ppc: Drop bat_rw
rockchip: Correct a reference to CONFIG_BOOT_MODE_REG
cmd: Add an option to enable the ini command
cmd: Drop mfsl command
Correct CONFIG_CONTROLCENTERDC
Drop dataflash_mmc_mux command
Drop CONFIG_DM644X_GPIO
Makefile: Avoid use of invalid CONFIG_ option
env: Drop ENV_IS_IN_SATA
samsung: Drop CONFIG_EXYNOS_PWM_BL
fpga: Add a LATTICE option
fpga: Add a FPGA_STRATIX_II option
misc: Drop mc9sdz60 driver
freescale: Drop unused pixis code
freescale: Drop unused ftpmu010 driver
rcar: Drop timer
imx: Drop unused CONFIG_IMX
arm: Drop old kona code
video: Drop unused lg4573 driver
m68k: Drop unused CONFIG_M52277
m68k: Drop unused CONFIG_MACH_DAVINCI_DA830_EVM
arm: Drop CONFIG_MMU
arc: Drop CONFIG_MMU
gpio: Drop unused mpc83xx_gpio driver
imx: Rename CONFIG_MXS to CFG_MXS
nand: Drop unused actl_nand driver
mtd: Drop unused fsl_upm driver
mtd: Drop unused fsmc_nand driver
mtd: Drop unused kb9202_nand driver
mtd: Drop unused nand_plat driver
Makefile: Drop CONFIG_OF_EARLY_FLATTREE
omap: Drop unused CONFIG_OMAP_USB_PHY
mtd: Drop unused CONFIG_ONENAND_U_BOOT
ppc: Drop unused CONFIG_P2020DS
gpio: Drop unused pca9698 driver
samsung: Rename PINCTRL_EXYNOS78x0
power: Drop unused bat_trats driver and battery code
power: Drop unused fg_max17042 driver and fuel gauge code
power: Drop unused muic_max77693 driver and mfd code
power: Drop unused muic_max8997 driver
freescale: Drop unused pq-mds-pib driver
rmobile: Drop CONFIG_RMOBILE
rtc: Drop old and unused drivers
mtd: Drop unused CONFIG_S32V234
mtd: Drop unused scf0403_lcd driver
rmobile: Drop CONFIG_SH73A0 and associated code
sh4: Drop unused pci_sh7780 driver
Drop ubsha1 tool
sysreset: at91: Correct Makefile rule for SYSRESET_AT91
gdsys: Drop unused fpga file
sh4: Drop unused kona_i2c driver
compulab: Drop CONFIG_TARGET_MCM_IMX8M_MINI
freescale: Drop CONFIG_TARGET_MPC8536DS et al
sh4: Drop unused twl6030 driver
ppc: Makefile: Drop unused ppc4xx code
armada: usb: net: Drop unused USB drivers
usb: Drop unused ehci-faraday driver
usb: Drop unused fotg210 gadget
rmobile: Drop unused ehci-rmobile driver
usb: Drop unused ehci-vct driver
usb: Drop unused sl811-hcd driver
imx: Drop CONFIG_USE_PLUGIN
freescale: Drop unused vsc3316_3308 driver
tools: Drop xway-swap-bytes tool
freescale: Drop unused zm7300 driver
fdt: Drop use of non-existent OF_PLATDATA option
Makefile | 24 +-
README | 7 -
arch/arc/config.mk | 4 -
arch/arc/lib/ints_low.S | 5 -
arch/arm/cpu/arm920t/Makefile | 2 -
arch/arm/cpu/armv7/Makefile | 2 -
arch/arm/cpu/armv7/kona-common/Makefile | 8 -
arch/arm/cpu/armv7/kona-common/clk-stubs.c | 25 -
.../arm/cpu/armv7/kona-common/hwinit-common.c | 17 -
arch/arm/cpu/armv7/kona-common/reset.S | 25 -
arch/arm/cpu/armv7/kona-common/s_init.c | 11 -
arch/arm/cpu/armv8/Makefile | 1 -
arch/arm/lib/debug.S | 21 -
arch/arm/mach-exynos/Kconfig | 6 +-
arch/arm/mach-mvebu/Makefile | 4 +-
arch/arm/mach-rmobile/Makefile | 2 -
arch/arm/mach-rmobile/cpu_info-sh73a0.c | 43 -
arch/arm/mach-rmobile/cpu_info.c | 1 -
.../mach-rmobile/include/mach/ehci-rmobile.h | 146 -
arch/arm/mach-rmobile/include/mach/gpio.h | 5 +-
arch/arm/mach-rmobile/include/mach/rmobile.h | 5 +-
.../mach-rmobile/include/mach/sh73a0-gpio.h | 553 ----
arch/arm/mach-rmobile/include/mach/sh73a0.h | 289 --
arch/arm/mach-rmobile/pfc-sh73a0.c | 2807 -----------------
arch/arm/mach-rmobile/timer.c | 87 -
arch/arm/mach-rockchip/Makefile | 2 +-
arch/m68k/Makefile | 1 -
arch/mips/mach-octeon/octeon_fdt.c | 43 +-
arch/powerpc/lib/Makefile | 1 -
arch/powerpc/lib/bat_rw.c | 244 --
arch/sandbox/config.mk | 2 -
arch/sh/include/asm/pci.h | 2 -
.../compulab/imx8mm-cl-iot-gate/ddr/Makefile | 4 -
board/davinci/da8xxevm/Makefile | 1 -
board/freescale/common/Makefile | 8 -
board/freescale/common/pixis.c | 470 ---
board/freescale/common/pixis.h | 54 -
board/freescale/common/pq-mds-pib.c | 60 -
board/freescale/common/pq-mds-pib.h | 9 -
board/freescale/common/vsc3316_3308.c | 530 ----
board/freescale/common/zm7300.c | 232 --
board/freescale/common/zm7300.h | 21 -
board/freescale/mx7ulp_evk/Makefile | 4 -
board/gdsys/a38x/hre.c | 1 -
board/gdsys/common/Makefile | 3 +-
board/gdsys/common/fpga.c | 28 -
board/xes/common/Makefile | 1 -
board/xes/common/actl_nand.c | 49 -
cmd/Kconfig | 7 +
cmd/Makefile | 2 -
cmd/dataflash_mmc_mux.c | 48 -
cmd/mfsl.c | 387 ---
cmd/nvedit.c | 1 -
common/usb_hub.c | 6 -
drivers/Makefile | 1 -
drivers/fpga/Kconfig | 12 +
drivers/gpio/Makefile | 5 -
drivers/gpio/adi_gpio2.c | 425 ---
drivers/gpio/kona_gpio.c | 141 -
drivers/gpio/mpc83xx_gpio.c | 183 --
drivers/gpio/pca9698.c | 127 -
drivers/i2c/Makefile | 1 -
drivers/i2c/kona_i2c.c | 728 -----
drivers/i2c/sh_i2c.c | 5 -
drivers/input/Makefile | 1 -
drivers/input/twl6030.c | 47 -
drivers/misc/Makefile | 2 -
drivers/misc/ali512x.c | 401 ---
drivers/misc/mc9sdz60.c | 34 -
drivers/mtd/nand/raw/Makefile | 5 -
drivers/mtd/nand/raw/fsl_upm.c | 187 --
drivers/mtd/nand/raw/fsmc_nand.c | 470 ---
drivers/mtd/nand/raw/kb9202_nand.c | 134 -
drivers/mtd/nand/raw/nand_plat.c | 65 -
drivers/pci/Makefile | 1 -
drivers/pci/pci_sh7780.c | 92 -
drivers/pinctrl/exynos/Kconfig | 2 +-
drivers/pinctrl/exynos/Makefile | 2 +-
drivers/power/Makefile | 4 -
drivers/power/battery/Makefile | 7 -
drivers/power/battery/bat_trats.c | 91 -
drivers/power/battery/bat_trats2.c | 65 -
drivers/power/ftpmu010.c | 87 -
drivers/power/fuel_gauge/Makefile | 6 -
drivers/power/fuel_gauge/fg_max17042.c | 287 --
drivers/power/mfd/Makefile | 8 -
drivers/power/mfd/fg_max77693.c | 137 -
drivers/power/mfd/muic_max77693.c | 77 -
drivers/power/mfd/pmic_max77693.c | 96 -
drivers/power/pmic/Makefile | 1 -
drivers/power/pmic/muic_max8997.c | 74 -
drivers/rtc/Makefile | 14 -
drivers/rtc/at91sam9_rtt.c | 78 -
drivers/rtc/ds1302.c | 329 --
drivers/rtc/ds1306.c | 438 ---
drivers/rtc/ftrtc010.c | 122 -
drivers/rtc/imxdi.c | 223 --
drivers/rtc/max6900.c | 105 -
drivers/rtc/mk48t59.c | 175 -
drivers/rtc/mx27rtc.c | 64 -
drivers/rtc/rs5c372.c | 256 --
drivers/rtc/s3c24x0_rtc.c | 149 -
drivers/rtc/x1205.c | 161 -
drivers/serial/serial_sh.h | 10 +-
drivers/sysreset/Makefile | 2 +-
drivers/usb/gadget/Makefile | 3 +-
drivers/usb/gadget/fotg210.c | 964 ------
drivers/usb/gadget/gadget_chips.h | 8 -
drivers/usb/host/Makefile | 5 -
drivers/usb/host/ehci-armada100.c | 48 -
drivers/usb/host/ehci-faraday.c | 144 -
drivers/usb/host/ehci-hcd.c | 5 -
drivers/usb/host/ehci-rmobile.c | 129 -
drivers/usb/host/ehci-vct.c | 44 -
drivers/usb/host/sl811-hcd.c | 714 -----
drivers/usb/host/sl811.h | 104 -
drivers/usb/host/utmi-armada100.c | 80 -
drivers/video/Makefile | 2 -
drivers/video/exynos/Makefile | 1 -
drivers/video/lg4573.c | 331 --
drivers/video/scf0403_lcd.c | 297 --
dts/Kconfig | 4 +-
env/Makefile | 1 -
env/env.c | 3 -
env/sata.c | 122 -
include/faraday/ftpmu010.h | 234 --
include/linux/mtd/fsl_upm.h | 44 -
include/linux/mtd/fsmc_nand.h | 84 -
include/netdev.h | 1 -
include/pca9698.h | 17 -
include/power/fg_battery_cell_params.h | 73 -
include/scf0403_lcd.h | 10 -
include/usb/fotg210.h | 362 ---
include/usb/fusbh200.h | 59 -
tools/.gitignore | 1 -
tools/Makefile | 14 +-
tools/moveconfig.py | 334 ++
tools/mxsimage.c | 2 +-
tools/ubsha1.c | 83 -
tools/xway-swap-bytes.c | 38 -
140 files changed, 376 insertions(+), 16447 deletions(-)
delete mode 100644 arch/arm/cpu/armv7/kona-common/Makefile
delete mode 100644 arch/arm/cpu/armv7/kona-common/clk-stubs.c
delete mode 100644 arch/arm/cpu/armv7/kona-common/hwinit-common.c
delete mode 100644 arch/arm/cpu/armv7/kona-common/reset.S
delete mode 100644 arch/arm/cpu/armv7/kona-common/s_init.c
delete mode 100644 arch/arm/mach-rmobile/cpu_info-sh73a0.c
delete mode 100644 arch/arm/mach-rmobile/include/mach/ehci-rmobile.h
delete mode 100644 arch/arm/mach-rmobile/include/mach/sh73a0-gpio.h
delete mode 100644 arch/arm/mach-rmobile/include/mach/sh73a0.h
delete mode 100644 arch/arm/mach-rmobile/pfc-sh73a0.c
delete mode 100644 arch/arm/mach-rmobile/timer.c
delete mode 100644 arch/powerpc/lib/bat_rw.c
delete mode 100644 board/freescale/common/pixis.c
delete mode 100644 board/freescale/common/pixis.h
delete mode 100644 board/freescale/common/pq-mds-pib.c
delete mode 100644 board/freescale/common/pq-mds-pib.h
delete mode 100644 board/freescale/common/vsc3316_3308.c
delete mode 100644 board/freescale/common/zm7300.c
delete mode 100644 board/freescale/common/zm7300.h
delete mode 100644 board/gdsys/common/fpga.c
delete mode 100644 board/xes/common/actl_nand.c
delete mode 100644 cmd/dataflash_mmc_mux.c
delete mode 100644 cmd/mfsl.c
delete mode 100644 drivers/gpio/adi_gpio2.c
delete mode 100644 drivers/gpio/kona_gpio.c
delete mode 100644 drivers/gpio/mpc83xx_gpio.c
delete mode 100644 drivers/gpio/pca9698.c
delete mode 100644 drivers/i2c/kona_i2c.c
delete mode 100644 drivers/input/twl6030.c
delete mode 100644 drivers/misc/ali512x.c
delete mode 100644 drivers/misc/mc9sdz60.c
delete mode 100644 drivers/mtd/nand/raw/fsl_upm.c
delete mode 100644 drivers/mtd/nand/raw/fsmc_nand.c
delete mode 100644 drivers/mtd/nand/raw/kb9202_nand.c
delete mode 100644 drivers/mtd/nand/raw/nand_plat.c
delete mode 100644 drivers/pci/pci_sh7780.c
delete mode 100644 drivers/power/battery/Makefile
delete mode 100644 drivers/power/battery/bat_trats.c
delete mode 100644 drivers/power/battery/bat_trats2.c
delete mode 100644 drivers/power/ftpmu010.c
delete mode 100644 drivers/power/fuel_gauge/Makefile
delete mode 100644 drivers/power/fuel_gauge/fg_max17042.c
delete mode 100644 drivers/power/mfd/Makefile
delete mode 100644 drivers/power/mfd/fg_max77693.c
delete mode 100644 drivers/power/mfd/muic_max77693.c
delete mode 100644 drivers/power/mfd/pmic_max77693.c
delete mode 100644 drivers/power/pmic/muic_max8997.c
delete mode 100644 drivers/rtc/at91sam9_rtt.c
delete mode 100644 drivers/rtc/ds1302.c
delete mode 100644 drivers/rtc/ds1306.c
delete mode 100644 drivers/rtc/ftrtc010.c
delete mode 100644 drivers/rtc/imxdi.c
delete mode 100644 drivers/rtc/max6900.c
delete mode 100644 drivers/rtc/mk48t59.c
delete mode 100644 drivers/rtc/mx27rtc.c
delete mode 100644 drivers/rtc/rs5c372.c
delete mode 100644 drivers/rtc/s3c24x0_rtc.c
delete mode 100644 drivers/rtc/x1205.c
delete mode 100644 drivers/usb/gadget/fotg210.c
delete mode 100644 drivers/usb/host/ehci-armada100.c
delete mode 100644 drivers/usb/host/ehci-faraday.c
delete mode 100644 drivers/usb/host/ehci-rmobile.c
delete mode 100644 drivers/usb/host/ehci-vct.c
delete mode 100644 drivers/usb/host/sl811-hcd.c
delete mode 100644 drivers/usb/host/sl811.h
delete mode 100644 drivers/usb/host/utmi-armada100.c
delete mode 100644 drivers/video/lg4573.c
delete mode 100644 drivers/video/scf0403_lcd.c
delete mode 100644 env/sata.c
delete mode 100644 include/faraday/ftpmu010.h
delete mode 100644 include/linux/mtd/fsl_upm.h
delete mode 100644 include/linux/mtd/fsmc_nand.h
delete mode 100644 include/pca9698.h
delete mode 100644 include/power/fg_battery_cell_params.h
delete mode 100644 include/scf0403_lcd.h
delete mode 100644 include/usb/fotg210.h
delete mode 100644 include/usb/fusbh200.h
delete mode 100644 tools/ubsha1.c
delete mode 100644 tools/xway-swap-bytes.c
--
2.39.1.456.gfc5497dd1b-goog
^ permalink raw reply [flat|nested] 87+ messages in thread* [PATCH v3 01/76] moveconfig: Add an option to compare Kconfig against source 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-08 1:37 ` Tom Rini 2023-02-01 20:19 ` [PATCH v3 02/76] power: Drop fg_max77693 Simon Glass ` (71 subsequent siblings) 72 siblings, 1 reply; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass Sometimes the Makefile rules or source code refers to Kconfig options which don't exist. Update the moveconfig tool to check this and produce a series of reports about inconsistencies. This can then be used to generate patches to correct the problems. Signed-off-by: Simon Glass <sjg@chromium.org> --- Changes in v3: - Update to support lower case CONFIG options - Drop efi_loader change tools/moveconfig.py | 334 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 334 insertions(+) diff --git a/tools/moveconfig.py b/tools/moveconfig.py index 8f084a6070a..c4d72ede368 100755 --- a/tools/moveconfig.py +++ b/tools/moveconfig.py @@ -93,6 +93,18 @@ SIZES = { RE_REMOVE_DEFCONFIG = re.compile(r'(.*)_defconfig') +# CONFIG symbols present in the build system (from Linux) but not actually used +# in U-Boot; KCONFIG symbols +IGNORE_SYMS = ['DEBUG_SECTION_MISMATCH', 'FTRACE_MCOUNT_RECORD', 'GCOV_KERNEL', + 'GCOV_PROFILE_ALL', 'KALLSYMS', 'KASAN', 'MODVERSIONS', 'SHELL', + 'TPL_BUILD', 'VPL_BUILD', 'IS_ENABLED', 'FOO', 'IF_ENABLED_INT', + 'IS_ENABLED_', 'IS_ENABLED_1', 'IS_ENABLED_2', 'IS_ENABLED_3', + 'SPL_', 'TPL_', 'SPL_FOO', 'TPL_FOO', 'TOOLS_FOO', + 'ACME', 'SPL_ACME', 'TPL_ACME', 'TRACE_BRANCH_PROFILING', + 'VAL', '_UNDEFINED', 'SPL_BUILD', ] + +SPL_PREFIXES = ['SPL_', 'TPL_', 'VPL_', 'TOOLS_'] + ### helper functions ### def check_top_directory(): """Exit if we are not at the top of source directory.""" @@ -536,6 +548,7 @@ class KconfigScanner: os.environ['srctree'] = os.getcwd() os.environ['UBOOTVERSION'] = 'dummy' os.environ['KCONFIG_OBJDIR'] = '' + os.environ['CC'] = 'gcc' self.conf = kconfiglib.Kconfig() @@ -1593,6 +1606,319 @@ def prefix_config(cfg): return op + cfg +RE_MK_CONFIGS = re.compile('CONFIG_(\$\(SPL_(?:TPL_)?\))?([A-Za-z0-9_]*)') +RE_IFDEF = re.compile('(ifdef|ifndef)') +RE_C_CONFIGS = re.compile('CONFIG_([A-Za-z0-9_]*)') +RE_CONFIG_IS = re.compile('CONFIG_IS_ENABLED\(([A-Za-z0-9_]*)\)') + +class ConfigUse: + def __init__(self, cfg, is_spl, fname, rest): + self.cfg = cfg + self.is_spl = is_spl + self.fname = fname + self.rest = rest + + def __hash__(self): + return hash((self.cfg, self.is_spl)) + +def scan_makefiles(fnames): + """Scan Makefiles looking for Kconfig options + + Looks for uses of CONFIG options in Makefiles + + Args: + fnames (list of tuple): + str: Makefile filename where the option was found + str: Line of the Makefile + + Returns: + tuple: + dict: all_uses + key (ConfigUse): object + value (list of str): matching lines + dict: Uses by filename + key (str): filename + value (set of ConfigUse): uses in that filename + + >>> RE_MK_CONFIGS.search('CONFIG_FRED').groups() + (None, 'FRED') + >>> RE_MK_CONFIGS.search('CONFIG_$(SPL_)MARY').groups() + ('$(SPL_)', 'MARY') + >>> RE_MK_CONFIGS.search('CONFIG_$(SPL_TPL_)MARY').groups() + ('$(SPL_TPL_)', 'MARY') + """ + all_uses = collections.defaultdict(list) + fname_uses = {} + for fname, rest in fnames: + m_iter = RE_MK_CONFIGS.finditer(rest) + found = False + for m in m_iter: + found = True + real_opt = m.group(2) + if real_opt == '': + continue + is_spl = False + if m.group(1): + is_spl = True + use = ConfigUse(real_opt, is_spl, fname, rest) + if fname not in fname_uses: + fname_uses[fname] = set() + fname_uses[fname].add(use) + all_uses[use].append(rest) + return all_uses, fname_uses + + +def scan_src_files(fnames): + """Scan source files (other than Makefiles) looking for Kconfig options + + Looks for uses of CONFIG options + + Args: + fnames (list of tuple): + str: Makefile filename where the option was found + str: Line of the Makefile + + Returns: + tuple: + dict: all_uses + key (ConfigUse): object + value (list of str): matching lines + dict: Uses by filename + key (str): filename + value (set of ConfigUse): uses in that filename + + >>> RE_C_CONFIGS.search('CONFIG_FRED').groups() + ('FRED',) + >>> RE_CONFIG_IS.search('CONFIG_IS_ENABLED(MARY)').groups() + ('MARY',) + >>> RE_CONFIG_IS.search('#if CONFIG_IS_ENABLED(OF_PLATDATA)').groups() + ('OF_PLATDATA',) + """ + def add_uses(m_iter, is_spl): + for m in m_iter: + found = True + real_opt = m.group(1) + if real_opt == '': + continue + use = ConfigUse(real_opt, is_spl, fname, rest) + if fname not in fname_uses: + fname_uses[fname] = set() + fname_uses[fname].add(use) + all_uses[use].append(rest) + + all_uses = collections.defaultdict(list) + fname_uses = {} + for fname, rest in fnames: + m_iter = RE_C_CONFIGS.finditer(rest) + add_uses(m_iter, False) + + m_iter2 = RE_CONFIG_IS.finditer(rest) + add_uses(m_iter2, True) + + return all_uses, fname_uses + + +MODE_NORMAL, MODE_SPL, MODE_PROPER = range(3) + +def do_scan_source(path, do_update): + """Scan the source tree for Kconfig inconsistencies + + Args: + path (str): Path to source tree + do_update (bool) : True to write to scripts/kconf_... files + """ + def is_not_proper(name): + for prefix in SPL_PREFIXES: + if name.startswith(prefix): + return name[len(prefix):] + return False + + def check_not_found(all_uses, spl_mode): + """Check for Kconfig options mentioned in the source but not in Kconfig + + Args: + all_uses (dict): + key (ConfigUse): object + value (list of str): matching lines + spl_mode (int): If MODE_SPL, look at source code which implies + an SPL_ option, but for which there is none; + for MOD_PROPER, look at source code which implies a Proper + option (i.e. use of CONFIG_IS_ENABLED() or $(SPL_) or + $(SPL_TPL_) but for which there none; + if MODE_NORMAL, ignore SPL + + Returns: + dict: + key (str): CONFIG name (without 'CONFIG_' prefix + value (list of ConfigUse): List of uses of this CONFIG + """ + # Make sure we know about all the options + not_found = collections.defaultdict(list) + for use, rest in all_uses.items(): + name = use.cfg + if name in IGNORE_SYMS: + continue + check = True + + if spl_mode == MODE_SPL: + check = use.is_spl + + # If it is an SPL symbol, try prepending all SPL_ prefixes to + # find at least one SPL symbol + if use.is_spl: + add_to_dict = False + for prefix in SPL_PREFIXES: + try_name = prefix + name + sym = kconf.syms.get(try_name) + if sym: + break + if not sym: + not_found[f'SPL_{name}'].append(use) + continue + elif spl_mode == MODE_PROPER: + # Try to find the Proper version of this symbol, i.e. without + # the SPL_ prefix + proper_name = is_not_proper(name) + if proper_name: + name = proper_name + elif not use.is_spl: + check = False + else: # MODE_NORMAL + debug = False + sym = kconf.syms.get(name) + if not sym: + proper_name = is_not_proper(name) + if proper_name: + name = proper_name + sym = kconf.syms.get(name) + if not sym: + for prefix in SPL_PREFIXES: + try_name = prefix + name + sym = kconf.syms.get(try_name) + if sym: + break + if not sym: + not_found[name].append(use) + continue + + sym = kconf.syms.get(name) + if not sym and check: + not_found[name].append(use) + return not_found + + def show_uses(uses): + """Show a list of uses along with their filename and code snippet + + Args: + uses (dict): + key (str): CONFIG name (without 'CONFIG_' prefix + value (list of ConfigUse): List of uses of this CONFIG + """ + for name in sorted(uses): + print(f'{name}: ', end='') + for i, use in enumerate(uses[name]): + print(f'{" " if i else ""}{use.fname}: {use.rest.strip()}') + + + print('Scanning Kconfig') + kconf = KconfigScanner().conf + print(f'Scanning source in {path}') + args = ['git', 'grep', '-E', r'IS_ENABLED|\bCONFIG'] + with subprocess.Popen(args, stdout=subprocess.PIPE) as proc: + out, err = proc.communicate() + lines = out.splitlines() + re_fname = re.compile('^([^:]*):(.*)') + src_list = [] + mk_list = [] + for line in lines: + linestr = line.decode('utf-8') + m_fname = re_fname.search(linestr) + if not m_fname: + continue + fname, rest = m_fname.groups() + dirname, leaf = os.path.split(fname) + root, ext = os.path.splitext(leaf) + if ext == '.autoconf': + pass + elif ext in ['.c', '.h', '.S', '.lds', '.dts', '.dtsi', '.asl', '.cfg', + '.env', '.tmpl']: + src_list.append([fname, rest]) + elif 'Makefile' in root or ext == '.mk': + mk_list.append([fname, rest]) + elif ext in ['.yml', '.sh', '.py', '.awk', '.pl', '.rst', '', '.sed']: + pass + elif 'Kconfig' in root or 'Kbuild' in root: + pass + elif 'README' in root: + pass + elif dirname in ['configs']: + pass + elif dirname.startswith('doc') or dirname.startswith('scripts/kconfig'): + pass + else: + print(f'Not sure how to handle file {fname}') + + # Scan the Makefiles + all_uses, fname_uses = scan_makefiles(mk_list) + + spl_not_found = set() + proper_not_found = set() + + # Make sure we know about all the options + print('\nCONFIG options present in Makefiles but not Kconfig:') + not_found = check_not_found(all_uses, MODE_NORMAL) + show_uses(not_found) + + print('\nCONFIG options present in Makefiles but not Kconfig (SPL):') + not_found = check_not_found(all_uses, MODE_SPL) + show_uses(not_found) + spl_not_found |= set([is_not_proper(key) or key for key in not_found.keys()]) + + print('\nCONFIG options used as Proper in Makefiles but without a non-SPL_ variant:') + not_found = check_not_found(all_uses, MODE_PROPER) + show_uses(not_found) + proper_not_found |= set([key for key in not_found.keys()]) + + # Scan the source code + all_uses, fname_uses = scan_src_files(src_list) + + # Make sure we know about all the options + print('\nCONFIG options present in source but not Kconfig:') + not_found = check_not_found(all_uses, MODE_NORMAL) + show_uses(not_found) + + print('\nCONFIG options present in source but not Kconfig (SPL):') + not_found = check_not_found(all_uses, MODE_SPL) + show_uses(not_found) + spl_not_found |= set([is_not_proper(key) or key for key in not_found.keys()]) + + print('\nCONFIG options used as Proper in source but without a non-SPL_ variant:') + not_found = check_not_found(all_uses, MODE_PROPER) + show_uses(not_found) + proper_not_found |= set([key for key in not_found.keys()]) + + print('\nCONFIG options used as SPL but without an SPL_ variant:') + for item in sorted(spl_not_found): + print(f' {item}') + + print('\nCONFIG options used as Proper but without a non-SPL_ variant:') + for item in sorted(proper_not_found): + print(f' {item}') + + # Write out the updated information + if do_update: + with open(os.path.join(path, 'scripts', 'conf_nospl'), 'w') as out: + print('# These options should not be enabled in SPL builds\n', + file=out) + for item in sorted(spl_not_found): + print(item, file=out) + with open(os.path.join(path, 'scripts', 'conf_noproper'), 'w') as out: + print('# These options should not be enabled in Proper builds\n', + file=out) + for item in sorted(proper_not_found): + print(item, file=out) + + def main(): try: cpu_count = multiprocessing.cpu_count() @@ -1642,10 +1968,14 @@ doc/develop/moveconfig.rst for documentation.''' help='force sync by savedefconfig') parser.add_argument('-S', '--spl', action='store_true', default=False, help='parse config options defined for SPL build') + parser.add_argument('--scan-source', action='store_true', default=False, + help='scan source for uses of CONFIG options') parser.add_argument('-t', '--test', action='store_true', default=False, help='run unit tests') parser.add_argument('-y', '--yes', action='store_true', default=False, help="respond 'yes' to any prompts") + parser.add_argument('-u', '--update', action='store_true', default=False, + help="update scripts/ files (use with --scan-source)") parser.add_argument('-v', '--verbose', action='store_true', default=False, help='show any build errors as boards are built') parser.add_argument('configs', nargs='*') @@ -1660,6 +1990,10 @@ doc/develop/moveconfig.rst for documentation.''' return 1 unittest.main() + if args.scan_source: + do_scan_source(os.getcwd(), args.update) + return + if not any((len(configs), args.force_sync, args.build_db, args.imply, args.find)): parser.print_usage() -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* Re: [PATCH v3 01/76] moveconfig: Add an option to compare Kconfig against source 2023-02-01 20:19 ` [PATCH v3 01/76] moveconfig: Add an option to compare Kconfig against source Simon Glass @ 2023-02-08 1:37 ` Tom Rini 2023-02-08 18:28 ` Simon Glass 0 siblings, 1 reply; 87+ messages in thread From: Tom Rini @ 2023-02-08 1:37 UTC (permalink / raw) To: Simon Glass; +Cc: u-boot [-- Attachment #1: Type: text/plain, Size: 564 bytes --] On Wed, Feb 01, 2023 at 01:19:12PM -0700, Simon Glass wrote: > Sometimes the Makefile rules or source code refers to Kconfig options > which don't exist. Update the moveconfig tool to check this and produce > a series of reports about inconsistencies. > > This can then be used to generate patches to correct the problems. > > Signed-off-by: Simon Glass <sjg@chromium.org> For the series, except for 46/76 which was a rename not dropped in v3, and the one or two that look to be missing in patchwork, applied to u-boot/master, thanks! -- Tom [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 659 bytes --] ^ permalink raw reply [flat|nested] 87+ messages in thread
* Re: [PATCH v3 01/76] moveconfig: Add an option to compare Kconfig against source 2023-02-08 1:37 ` Tom Rini @ 2023-02-08 18:28 ` Simon Glass 2023-02-08 18:35 ` Tom Rini 0 siblings, 1 reply; 87+ messages in thread From: Simon Glass @ 2023-02-08 18:28 UTC (permalink / raw) To: Tom Rini; +Cc: u-boot Hi Tom, On Tue, 7 Feb 2023 at 18:37, Tom Rini <trini@konsulko.com> wrote: > > On Wed, Feb 01, 2023 at 01:19:12PM -0700, Simon Glass wrote: > > > Sometimes the Makefile rules or source code refers to Kconfig options > > which don't exist. Update the moveconfig tool to check this and produce > > a series of reports about inconsistencies. > > > > This can then be used to generate patches to correct the problems. > > > > Signed-off-by: Simon Glass <sjg@chromium.org> > > For the series, except for 46/76 which was a rename not dropped in v3, > and the one or two that look to be missing in patchwork, applied to > u-boot/master, thanks! OK thanks. It looks like these four patches: sh4: Drop unused twl6030 driver samsung: Rename PINCTRL_EXYNOS78x0 (should be dropped) mtd: Drop unused CONFIG_ONENAND_U_BOOT mtd: Drop unused kb9202_nand driver I'm not sure what is wrong with patchwork, or even if it is patchwork, but things seem to be lost sometimes. Regards, Simon ^ permalink raw reply [flat|nested] 87+ messages in thread
* Re: [PATCH v3 01/76] moveconfig: Add an option to compare Kconfig against source 2023-02-08 18:28 ` Simon Glass @ 2023-02-08 18:35 ` Tom Rini 2023-02-08 19:06 ` Simon Glass 0 siblings, 1 reply; 87+ messages in thread From: Tom Rini @ 2023-02-08 18:35 UTC (permalink / raw) To: Simon Glass; +Cc: u-boot [-- Attachment #1: Type: text/plain, Size: 1431 bytes --] On Wed, Feb 08, 2023 at 11:28:22AM -0700, Simon Glass wrote: > Hi Tom, > > On Tue, 7 Feb 2023 at 18:37, Tom Rini <trini@konsulko.com> wrote: > > > > On Wed, Feb 01, 2023 at 01:19:12PM -0700, Simon Glass wrote: > > > > > Sometimes the Makefile rules or source code refers to Kconfig options > > > which don't exist. Update the moveconfig tool to check this and produce > > > a series of reports about inconsistencies. > > > > > > This can then be used to generate patches to correct the problems. > > > > > > Signed-off-by: Simon Glass <sjg@chromium.org> > > > > For the series, except for 46/76 which was a rename not dropped in v3, > > and the one or two that look to be missing in patchwork, applied to > > u-boot/master, thanks! > > OK thanks. It looks like these four patches: > > sh4: Drop unused twl6030 driver > samsung: Rename PINCTRL_EXYNOS78x0 (should be dropped) > mtd: Drop unused CONFIG_ONENAND_U_BOOT > mtd: Drop unused kb9202_nand driver > > I'm not sure what is wrong with patchwork, or even if it is patchwork, > but things seem to be lost sometimes. I suspect Google dropped them on the floor as lore.kernel.org is also missing v3 for the 3 of those that weren't supposed to be dropped. I noticed you had some of the problems I've also had when posting very large/long series where sometimes it'll get rejected and you need to pick up and continue after a bit. -- Tom [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 659 bytes --] ^ permalink raw reply [flat|nested] 87+ messages in thread
* Re: [PATCH v3 01/76] moveconfig: Add an option to compare Kconfig against source 2023-02-08 18:35 ` Tom Rini @ 2023-02-08 19:06 ` Simon Glass 0 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-08 19:06 UTC (permalink / raw) To: Tom Rini; +Cc: U-Boot Mailing List Hi Tom, On Wed, 8 Feb 2023 at 11:35, Tom Rini <trini@konsulko.com> wrote: > > On Wed, Feb 08, 2023 at 11:28:22AM -0700, Simon Glass wrote: > > Hi Tom, > > > > On Tue, 7 Feb 2023 at 18:37, Tom Rini <trini@konsulko.com> wrote: > > > > > > On Wed, Feb 01, 2023 at 01:19:12PM -0700, Simon Glass wrote: > > > > > > > Sometimes the Makefile rules or source code refers to Kconfig options > > > > which don't exist. Update the moveconfig tool to check this and produce > > > > a series of reports about inconsistencies. > > > > > > > > This can then be used to generate patches to correct the problems. > > > > > > > > Signed-off-by: Simon Glass <sjg@chromium.org> > > > > > > For the series, except for 46/76 which was a rename not dropped in v3, > > > and the one or two that look to be missing in patchwork, applied to > > > u-boot/master, thanks! > > > > OK thanks. It looks like these four patches: > > > > sh4: Drop unused twl6030 driver > > samsung: Rename PINCTRL_EXYNOS78x0 (should be dropped) > > mtd: Drop unused CONFIG_ONENAND_U_BOOT > > mtd: Drop unused kb9202_nand driver > > > > I'm not sure what is wrong with patchwork, or even if it is patchwork, > > but things seem to be lost sometimes. > > I suspect Google dropped them on the floor as lore.kernel.org is also > missing v3 for the 3 of those that weren't supposed to be dropped. I > noticed you had some of the problems I've also had when posting very > large/long series where sometimes it'll get rejected and you need to > pick up and continue after a bit. Sadly, I think you are right. Regards, Simon ^ permalink raw reply [flat|nested] 87+ messages in thread
* [PATCH v3 02/76] power: Drop fg_max77693 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass 2023-02-01 20:19 ` [PATCH v3 01/76] moveconfig: Add an option to compare Kconfig against source Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 03/76] nand: Drop CONFIG_NAND_SPEAR Simon Glass ` (70 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used in U-Boot. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/power/mfd/Makefile | 1 - drivers/power/mfd/fg_max77693.c | 137 -------------------------------- 2 files changed, 138 deletions(-) delete mode 100644 drivers/power/mfd/fg_max77693.c diff --git a/drivers/power/mfd/Makefile b/drivers/power/mfd/Makefile index a8eb7f81e72..5dfbdbd1b0f 100644 --- a/drivers/power/mfd/Makefile +++ b/drivers/power/mfd/Makefile @@ -5,4 +5,3 @@ obj-$(CONFIG_POWER_PMIC_MAX77693) += pmic_max77693.o obj-$(CONFIG_POWER_MUIC_MAX77693) += muic_max77693.o -obj-$(CONFIG_POWER_FG_MAX77693) += fg_max77693.o diff --git a/drivers/power/mfd/fg_max77693.c b/drivers/power/mfd/fg_max77693.c deleted file mode 100644 index 983a6d4a2bd..00000000000 --- a/drivers/power/mfd/fg_max77693.c +++ /dev/null @@ -1,137 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2013 Samsung Electronics - * Piotr Wilczek <p.wilczek@samsung.com> - */ - -#include <common.h> -#include <log.h> -#include <power/pmic.h> -#include <power/max77693_fg.h> -#include <i2c.h> -#include <power/power_chrg.h> -#include <power/battery.h> -#include <power/fg_battery_cell_params.h> -#include <errno.h> - -static int max77693_get_vcell(u32 *vcell) -{ - u16 value; - u8 ret; - - ret = i2c_read(MAX77693_FUEL_I2C_ADDR, MAX77693_VCELL, 1, - (u8 *)&value, 2); - if (ret) - return ret; - - *vcell = (u32)(value >> 3); - *vcell = *vcell * 625; - - return 0; -} - -static int max77693_get_soc(u32 *soc) -{ - u16 value; - u8 ret; - - ret = i2c_read(MAX77693_FUEL_I2C_ADDR, MAX77693_VFSOC, 1, - (u8 *)&value, 2); - if (ret) - return ret; - - *soc = (u32)(value >> 8); - - return 0; -} - -static int power_update_battery(struct pmic *p, struct pmic *bat) -{ - struct power_battery *pb = bat->pbat; - int ret; - - if (pmic_probe(p)) { - puts("Can't find max77693 fuel gauge\n"); - return -ENODEV; - } - - ret = max77693_get_soc(&pb->bat->state_of_chrg); - if (ret) - return ret; - - max77693_get_vcell(&pb->bat->voltage_uV); - - return 0; -} - -static int power_check_battery(struct pmic *p, struct pmic *bat) -{ - struct power_battery *pb = bat->pbat; - unsigned int val; - int ret = 0; - - if (pmic_probe(p)) { - puts("Can't find max77693 fuel gauge\n"); - return -ENODEV; - } - - ret = pmic_reg_read(p, MAX77693_STATUS, &val); - if (ret) - return ret; - debug("fg status: 0x%x\n", val); - - ret = pmic_reg_read(p, MAX77693_VERSION, &pb->bat->version); - if (ret) - return ret; - - ret = power_update_battery(p, bat); - if (ret) - return ret; - debug("fg ver: 0x%x\n", pb->bat->version); - printf("BAT: state_of_charge(SOC):%d%%\n", - pb->bat->state_of_chrg); - - printf(" voltage: %d.%6.6d [V] (expected to be %d [mAh])\n", - pb->bat->voltage_uV / 1000000, - pb->bat->voltage_uV % 1000000, - pb->bat->capacity); - - if (pb->bat->voltage_uV > 3850000) - pb->bat->state = EXT_SOURCE; - else if (pb->bat->voltage_uV < 3600000 || pb->bat->state_of_chrg < 5) - pb->bat->state = CHARGE; - else - pb->bat->state = NORMAL; - - return 0; -} - -static struct power_fg power_fg_ops = { - .fg_battery_check = power_check_battery, - .fg_battery_update = power_update_battery, -}; - -int power_fg_init(unsigned char bus) -{ - static const char name[] = "MAX77693_FG"; - struct pmic *p = pmic_alloc(); - - if (!p) { - printf("%s: POWER allocation error!\n", __func__); - return -ENOMEM; - } - - debug("Board Fuel Gauge init\n"); - - p->name = name; - p->interface = PMIC_I2C; - p->number_of_regs = FG_NUM_OF_REGS; - p->hw.i2c.addr = MAX77693_FUEL_I2C_ADDR; - p->hw.i2c.tx_num = 2; - p->sensor_byte_order = PMIC_SENSOR_BYTE_ORDER_BIG; - p->bus = bus; - - p->fg = &power_fg_ops; - - return 0; -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 03/76] nand: Drop CONFIG_NAND_SPEAR 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass 2023-02-01 20:19 ` [PATCH v3 01/76] moveconfig: Add an option to compare Kconfig against source Simon Glass 2023-02-01 20:19 ` [PATCH v3 02/76] power: Drop fg_max77693 Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 04/76] power: Drop pmic_max77693.c Simon Glass ` (69 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Michael Trimarchi This is not used anymore. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> --- (no changes since v1) drivers/mtd/nand/raw/Makefile | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile index 7320d581e2f..4c59903aa8c 100644 --- a/drivers/mtd/nand/raw/Makefile +++ b/drivers/mtd/nand/raw/Makefile @@ -70,7 +70,6 @@ obj-$(CONFIG_NAND_MXS_DT) += mxs_nand_dt.o obj-$(CONFIG_NAND_OCTEONTX) += octeontx_nand.o obj-$(CONFIG_NAND_OCTEONTX_HW_ECC) += octeontx_bch.o obj-$(CONFIG_NAND_PXA3XX) += pxa3xx_nand.o -obj-$(CONFIG_NAND_SPEAR) += spr_nand.o obj-$(CONFIG_TEGRA_NAND) += tegra_nand.o obj-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o obj-$(CONFIG_NAND_OMAP_ELM) += omap_elm.o -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 04/76] power: Drop pmic_max77693.c 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (2 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 03/76] nand: Drop CONFIG_NAND_SPEAR Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 05/76] gpio: Drop adi_gpio2 Simon Glass ` (68 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass Drop this driver and the associated CONFIG option, as it is not used. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/power/mfd/Makefile | 1 - drivers/power/mfd/pmic_max77693.c | 96 ------------------------------- 2 files changed, 97 deletions(-) delete mode 100644 drivers/power/mfd/pmic_max77693.c diff --git a/drivers/power/mfd/Makefile b/drivers/power/mfd/Makefile index 5dfbdbd1b0f..b5ec8f00bb0 100644 --- a/drivers/power/mfd/Makefile +++ b/drivers/power/mfd/Makefile @@ -3,5 +3,4 @@ # Copyright (C) 2013 Samsung Electronics # Piotr Wilczek <p.wilczek@samsung.com> -obj-$(CONFIG_POWER_PMIC_MAX77693) += pmic_max77693.o obj-$(CONFIG_POWER_MUIC_MAX77693) += muic_max77693.o diff --git a/drivers/power/mfd/pmic_max77693.c b/drivers/power/mfd/pmic_max77693.c deleted file mode 100644 index e32a9722a40..00000000000 --- a/drivers/power/mfd/pmic_max77693.c +++ /dev/null @@ -1,96 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2013 Samsung Electronics - * Piotr Wilczek <p.wilczek@samsung.com> - */ - -#include <common.h> -#include <log.h> -#include <power/pmic.h> -#include <power/max77693_pmic.h> -#include <i2c.h> -#include <errno.h> - -static int max77693_charger_state(struct pmic *p, int state, int current) -{ - unsigned int val; - - if (pmic_probe(p)) - return -ENODEV; - - /* unlock write capability */ - val = MAX77693_CHG_UNLOCK; - pmic_reg_write(p, MAX77693_CHG_CNFG_06, val); - - if (state == PMIC_CHARGER_DISABLE) { - puts("Disable the charger.\n"); - pmic_reg_read(p, MAX77693_CHG_CNFG_00, &val); - val &= ~0x01; - pmic_reg_write(p, MAX77693_CHG_CNFG_00, val); - return -ENOTSUPP; - } - - if (current < CHARGER_MIN_CURRENT || current > CHARGER_MAX_CURRENT) { - printf("%s: Wrong charge current: %d [mA]\n", - __func__, current); - return -EINVAL; - } - - /* set charging current */ - pmic_reg_read(p, MAX77693_CHG_CNFG_02, &val); - val &= ~MAX77693_CHG_CC; - val |= current * 10 / 333; /* 0.1A/3 steps */ - pmic_reg_write(p, MAX77693_CHG_CNFG_02, val); - - /* enable charging */ - val = MAX77693_CHG_MODE_ON; - pmic_reg_write(p, MAX77693_CHG_CNFG_00, val); - - /* check charging current */ - pmic_reg_read(p, MAX77693_CHG_CNFG_02, &val); - val &= 0x3f; - printf("Enable the charger @ %d [mA]\n", val * 333 / 10); - - return 0; -} - -static int max77693_charger_bat_present(struct pmic *p) -{ - unsigned int val; - - if (pmic_probe(p)) - return -ENODEV; - - pmic_reg_read(p, MAX77693_CHG_INT_OK, &val); - - return !(val & MAX77693_CHG_DETBAT); -} - -static struct power_chrg power_chrg_pmic_ops = { - .chrg_bat_present = max77693_charger_bat_present, - .chrg_state = max77693_charger_state, -}; - -int pmic_init_max77693(unsigned char bus) -{ - static const char name[] = "MAX77693_PMIC"; - struct pmic *p = pmic_alloc(); - - if (!p) { - printf("%s: POWER allocation error!\n", __func__); - return -ENOMEM; - } - - debug("Board PMIC init\n"); - - p->name = name; - p->interface = PMIC_I2C; - p->number_of_regs = PMIC_NUM_OF_REGS; - p->hw.i2c.addr = MAX77693_PMIC_I2C_ADDR; - p->hw.i2c.tx_num = 1; - p->bus = bus; - - p->chrg = &power_chrg_pmic_ops; - - return 0; -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 05/76] gpio: Drop adi_gpio2 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (3 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 04/76] power: Drop pmic_max77693.c Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 06/76] Makefile: Drop CONFIG_AIS_CONFIG_FILE Simon Glass ` (67 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass Drop this unused driver. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/gpio/Makefile | 1 - drivers/gpio/adi_gpio2.c | 425 --------------------------------------- 2 files changed, 426 deletions(-) delete mode 100644 drivers/gpio/adi_gpio2.c diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 7235714fcc0..57603645c1c 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -47,7 +47,6 @@ obj-$(CONFIG_SH_GPIO_PFC) += sh_pfc.o obj-$(CONFIG_OMAP_GPIO) += omap_gpio.o obj-$(CONFIG_BCM2835_GPIO) += bcm2835_gpio.o obj-$(CONFIG_XILINX_GPIO) += xilinx_gpio.o -obj-$(CONFIG_ADI_GPIO2) += adi_gpio2.o obj-$(CONFIG_TCA642X) += tca642x.o obj-$(CONFIG_SUNXI_GPIO) += sunxi_gpio.o obj-$(CONFIG_LPC32XX_GPIO) += lpc32xx_gpio.o diff --git a/drivers/gpio/adi_gpio2.c b/drivers/gpio/adi_gpio2.c deleted file mode 100644 index d0849c85c3b..00000000000 --- a/drivers/gpio/adi_gpio2.c +++ /dev/null @@ -1,425 +0,0 @@ -/* - * ADI GPIO2 Abstraction Layer - * Support BF54x, BF60x and future processors. - * - * Copyright 2008-2013 Analog Devices Inc. - * - * Licensed under the GPL-2 or later - */ - -#include <common.h> -#include <malloc.h> -#include <linux/bug.h> -#include <linux/errno.h> -#include <asm/gpio.h> - -#define RESOURCE_LABEL_SIZE 16 - -static struct str_ident { - char name[RESOURCE_LABEL_SIZE]; -} str_ident[MAX_RESOURCES]; - -static void gpio_error(unsigned gpio) -{ - printf("adi_gpio2: GPIO %d wasn't requested!\n", gpio); -} - -static void set_label(unsigned short ident, const char *label) -{ - if (label) { - strncpy(str_ident[ident].name, label, - RESOURCE_LABEL_SIZE); - str_ident[ident].name[RESOURCE_LABEL_SIZE - 1] = 0; - } -} - -static char *get_label(unsigned short ident) -{ - return *str_ident[ident].name ? str_ident[ident].name : "UNKNOWN"; -} - -static int cmp_label(unsigned short ident, const char *label) -{ - if (label == NULL) - printf("adi_gpio2: please provide none-null label\n"); - - if (label) - return strcmp(str_ident[ident].name, label); - else - return -EINVAL; -} - -#define map_entry(m, i) reserved_##m##_map[gpio_bank(i)] -#define is_reserved(m, i, e) (map_entry(m, i) & gpio_bit(i)) -#define reserve(m, i) (map_entry(m, i) |= gpio_bit(i)) -#define unreserve(m, i) (map_entry(m, i) &= ~gpio_bit(i)) -#define DECLARE_RESERVED_MAP(m, c) unsigned short reserved_##m##_map[c] - -static DECLARE_RESERVED_MAP(gpio, GPIO_BANK_NUM); -static DECLARE_RESERVED_MAP(peri, gpio_bank(MAX_RESOURCES)); - -inline int check_gpio(unsigned gpio) -{ -#if defined(CONFIG_BF54x) - if (gpio == GPIO_PB15 || gpio == GPIO_PC14 || gpio == GPIO_PC15 || - gpio == GPIO_PH14 || gpio == GPIO_PH15 || - gpio == GPIO_PJ14 || gpio == GPIO_PJ15) - return -EINVAL; -#endif - if (gpio >= MAX_GPIOS) - return -EINVAL; - return 0; -} - -static void port_setup(unsigned gpio, unsigned short usage) -{ -#if defined(CONFIG_BF54x) - if (usage == GPIO_USAGE) - gpio_array[gpio_bank(gpio)]->port_fer &= ~gpio_bit(gpio); - else - gpio_array[gpio_bank(gpio)]->port_fer |= gpio_bit(gpio); -#else - if (usage == GPIO_USAGE) - gpio_array[gpio_bank(gpio)]->port_fer_clear = gpio_bit(gpio); - else - gpio_array[gpio_bank(gpio)]->port_fer_set = gpio_bit(gpio); -#endif -} - -inline void portmux_setup(unsigned short per) -{ - u32 pmux; - u16 ident = P_IDENT(per); - u16 function = P_FUNCT2MUX(per); - - pmux = gpio_array[gpio_bank(ident)]->port_mux; - - pmux &= ~(0x3 << (2 * gpio_sub_n(ident))); - pmux |= (function & 0x3) << (2 * gpio_sub_n(ident)); - - gpio_array[gpio_bank(ident)]->port_mux = pmux; -} - -inline u16 get_portmux(unsigned short per) -{ - u32 pmux; - u16 ident = P_IDENT(per); - - pmux = gpio_array[gpio_bank(ident)]->port_mux; - - return pmux >> (2 * gpio_sub_n(ident)) & 0x3; -} - -unsigned short get_gpio_dir(unsigned gpio) -{ - return 0x01 & - (gpio_array[gpio_bank(gpio)]->dir_clear >> gpio_sub_n(gpio)); -} - -/*********************************************************** -* -* FUNCTIONS: Peripheral Resource Allocation -* and PortMux Setup -* -* INPUTS/OUTPUTS: -* per Peripheral Identifier -* label String -* -* DESCRIPTION: Peripheral Resource Allocation and Setup API -**************************************************************/ - -int peripheral_request(unsigned short per, const char *label) -{ - unsigned short ident = P_IDENT(per); - - /* - * Don't cares are pins with only one dedicated function - */ - - if (per & P_DONTCARE) - return 0; - - if (!(per & P_DEFINED)) - return -EINVAL; - - BUG_ON(ident >= MAX_RESOURCES); - - /* If a pin can be muxed as either GPIO or peripheral, make - * sure it is not already a GPIO pin when we request it. - */ - if (unlikely(!check_gpio(ident) && is_reserved(gpio, ident, 1))) { - printf("%s: Peripheral %d is already reserved as GPIO by %s!\n", - __func__, ident, get_label(ident)); - return -EBUSY; - } - - if (unlikely(is_reserved(peri, ident, 1))) { - /* - * Pin functions like AMC address strobes my - * be requested and used by several drivers - */ - - if (!((per & P_MAYSHARE) && - get_portmux(per) == P_FUNCT2MUX(per))) { - /* - * Allow that the identical pin function can - * be requested from the same driver twice - */ - - if (cmp_label(ident, label) == 0) - goto anyway; - - printf("%s: Peripheral %d function %d is already " - "reserved by %s!\n", __func__, ident, - P_FUNCT2MUX(per), get_label(ident)); - return -EBUSY; - } - } - - anyway: - reserve(peri, ident); - - portmux_setup(per); - port_setup(ident, PERIPHERAL_USAGE); - - set_label(ident, label); - - return 0; -} - -int peripheral_request_list(const unsigned short per[], const char *label) -{ - u16 cnt; - int ret; - - for (cnt = 0; per[cnt] != 0; cnt++) { - ret = peripheral_request(per[cnt], label); - - if (ret < 0) { - for (; cnt > 0; cnt--) - peripheral_free(per[cnt - 1]); - - return ret; - } - } - - return 0; -} - -void peripheral_free(unsigned short per) -{ - unsigned short ident = P_IDENT(per); - - if (per & P_DONTCARE) - return; - - if (!(per & P_DEFINED)) - return; - - if (unlikely(!is_reserved(peri, ident, 0))) - return; - - if (!(per & P_MAYSHARE)) - port_setup(ident, GPIO_USAGE); - - unreserve(peri, ident); - - set_label(ident, "free"); -} - -void peripheral_free_list(const unsigned short per[]) -{ - u16 cnt; - for (cnt = 0; per[cnt] != 0; cnt++) - peripheral_free(per[cnt]); -} - -/*********************************************************** -* -* FUNCTIONS: GPIO Driver -* -* INPUTS/OUTPUTS: -* gpio PIO Number between 0 and MAX_GPIOS -* label String -* -* DESCRIPTION: GPIO Driver API -**************************************************************/ - -int gpio_request(unsigned gpio, const char *label) -{ - if (check_gpio(gpio) < 0) - return -EINVAL; - - /* - * Allow that the identical GPIO can - * be requested from the same driver twice - * Do nothing and return - - */ - - if (cmp_label(gpio, label) == 0) - return 0; - - if (unlikely(is_reserved(gpio, gpio, 1))) { - printf("adi_gpio2: GPIO %d is already reserved by %s!\n", - gpio, get_label(gpio)); - return -EBUSY; - } - if (unlikely(is_reserved(peri, gpio, 1))) { - printf("adi_gpio2: GPIO %d is already reserved as Peripheral " - "by %s!\n", gpio, get_label(gpio)); - return -EBUSY; - } - - reserve(gpio, gpio); - set_label(gpio, label); - - port_setup(gpio, GPIO_USAGE); - - return 0; -} - -int gpio_free(unsigned gpio) -{ - if (check_gpio(gpio) < 0) - return -1; - - if (unlikely(!is_reserved(gpio, gpio, 0))) { - gpio_error(gpio); - return -1; - } - - unreserve(gpio, gpio); - - set_label(gpio, "free"); - - return 0; -} - -#ifdef ADI_SPECIAL_GPIO_BANKS -static DECLARE_RESERVED_MAP(special_gpio, gpio_bank(MAX_RESOURCES)); - -int special_gpio_request(unsigned gpio, const char *label) -{ - /* - * Allow that the identical GPIO can - * be requested from the same driver twice - * Do nothing and return - - */ - - if (cmp_label(gpio, label) == 0) - return 0; - - if (unlikely(is_reserved(special_gpio, gpio, 1))) { - printf("adi_gpio2: GPIO %d is already reserved by %s!\n", - gpio, get_label(gpio)); - return -EBUSY; - } - if (unlikely(is_reserved(peri, gpio, 1))) { - printf("adi_gpio2: GPIO %d is already reserved as Peripheral " - "by %s!\n", gpio, get_label(gpio)); - - return -EBUSY; - } - - reserve(special_gpio, gpio); - reserve(peri, gpio); - - set_label(gpio, label); - port_setup(gpio, GPIO_USAGE); - - return 0; -} - -void special_gpio_free(unsigned gpio) -{ - if (unlikely(!is_reserved(special_gpio, gpio, 0))) { - gpio_error(gpio); - return; - } - - unreserve(special_gpio, gpio); - unreserve(peri, gpio); - set_label(gpio, "free"); -} -#endif - -static inline void __gpio_direction_input(unsigned gpio) -{ - gpio_array[gpio_bank(gpio)]->dir_clear = gpio_bit(gpio); -#if defined(CONFIG_BF54x) - gpio_array[gpio_bank(gpio)]->inen |= gpio_bit(gpio); -#else - gpio_array[gpio_bank(gpio)]->inen_set = gpio_bit(gpio); -#endif -} - -int gpio_direction_input(unsigned gpio) -{ - unsigned long flags; - - if (!is_reserved(gpio, gpio, 0)) { - gpio_error(gpio); - return -EINVAL; - } - - local_irq_save(flags); - __gpio_direction_input(gpio); - local_irq_restore(flags); - - return 0; -} - -int gpio_set_value(unsigned gpio, int arg) -{ - if (arg) - gpio_array[gpio_bank(gpio)]->data_set = gpio_bit(gpio); - else - gpio_array[gpio_bank(gpio)]->data_clear = gpio_bit(gpio); - - return 0; -} - -int gpio_direction_output(unsigned gpio, int value) -{ - unsigned long flags; - - if (!is_reserved(gpio, gpio, 0)) { - gpio_error(gpio); - return -EINVAL; - } - - local_irq_save(flags); - -#if defined(CONFIG_BF54x) - gpio_array[gpio_bank(gpio)]->inen &= ~gpio_bit(gpio); -#else - gpio_array[gpio_bank(gpio)]->inen_clear = gpio_bit(gpio); -#endif - gpio_set_value(gpio, value); - gpio_array[gpio_bank(gpio)]->dir_set = gpio_bit(gpio); - - local_irq_restore(flags); - - return 0; -} - -int gpio_get_value(unsigned gpio) -{ - return 1 & (gpio_array[gpio_bank(gpio)]->data >> gpio_sub_n(gpio)); -} - -void gpio_labels(void) -{ - int c, gpio; - - for (c = 0; c < MAX_RESOURCES; c++) { - gpio = is_reserved(gpio, c, 1); - if (!check_gpio(c) && gpio) - printf("GPIO_%d:\t%s\tGPIO %s\n", c, get_label(c), - get_gpio_dir(c) ? "OUTPUT" : "INPUT"); - else if (is_reserved(peri, c, 1)) - printf("GPIO_%d:\t%s\tPeripheral\n", c, get_label(c)); - else - continue; - } -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 06/76] Makefile: Drop CONFIG_AIS_CONFIG_FILE 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (4 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 05/76] gpio: Drop adi_gpio2 Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 07/76] misc: Drop ali512x Simon Glass ` (66 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not defined anywhere. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) Makefile | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/Makefile b/Makefile index 7eaf45496c1..c9d6d67310d 100644 --- a/Makefile +++ b/Makefile @@ -1528,8 +1528,7 @@ MKIMAGEFLAGS_u-boot.ubl = -n $(UBL_CONFIG) -T ublimage -e $(CONFIG_TEXT_BASE) u-boot.ubl: u-boot-with-spl.bin FORCE $(call if_changed,mkimage) -MKIMAGEFLAGS_u-boot-spl.ais = -s -n $(if $(CONFIG_AIS_CONFIG_FILE), \ - $(srctree)/$(CONFIG_AIS_CONFIG_FILE:"%"=%),"/dev/null") \ +MKIMAGEFLAGS_u-boot-spl.ais = -s -n "/dev/null" \ -T aisimage -e $(CONFIG_SPL_TEXT_BASE) spl/u-boot-spl.ais: spl/u-boot-spl.bin FORCE $(call if_changed,mkimage) -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 07/76] misc: Drop ali512x 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (5 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 06/76] Makefile: Drop CONFIG_AIS_CONFIG_FILE Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 08/76] sandbox: Drop reference to CONFIG_ARCH_DEVICE_TREE Simon Glass ` (65 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass Drop this unused driver. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/misc/Makefile | 1 - drivers/misc/ali512x.c | 401 ----------------------------------------- 2 files changed, 402 deletions(-) delete mode 100644 drivers/misc/ali512x.c diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile index d494639cd95..2de510329d8 100644 --- a/drivers/misc/Makefile +++ b/drivers/misc/Makefile @@ -29,7 +29,6 @@ ifdef CONFIG_SPL_BUILD obj-$(CONFIG_SANDBOX) += spltest_sandbox.o endif endif -obj-$(CONFIG_ALI152X) += ali512x.o obj-$(CONFIG_ALTERA_SYSID) += altera_sysid.o obj-$(CONFIG_ATSHA204A) += atsha204a-i2c.o obj-$(CONFIG_CBMEM_CONSOLE) += cbmem_console.o diff --git a/drivers/misc/ali512x.c b/drivers/misc/ali512x.c deleted file mode 100644 index e714e28bdc3..00000000000 --- a/drivers/misc/ali512x.c +++ /dev/null @@ -1,401 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2002 - * Daniel Engström, Omicron Ceti AB <daniel@omicron.se>. - */ - -/* - * Based on sc520cdp.c from rolo 1.6: - *---------------------------------------------------------------------- - * (C) Copyright 2000 - * Sysgo Real-Time Solutions GmbH - * Klein-Winternheim, Germany - *---------------------------------------------------------------------- - */ - -#include <config.h> - -#include <common.h> -#include <asm/io.h> -#include <ali512x.h> - - -/* ALI M5123 Logical device numbers: - * 0 FDC - * 1 unused? - * 2 unused? - * 3 lpt - * 4 UART1 - * 5 UART2 - * 6 RTC - * 7 mouse/kbd - * 8 CIO - */ - -/* - ************************************************************ - * Some access primitives for the ALi chip: * - ************************************************************ - */ - -static void ali_write(u8 index, u8 value) -{ - /* write an arbirary register */ - outb(index, ALI_INDEX); - outb(value, ALI_DATA); -} - -#if 0 -static int ali_read(u8 index) -{ - outb(index, ALI_INDEX); - return inb(ALI_DATA); -} -#endif - -#define ALI_OPEN() \ - outb(0x51, ALI_INDEX); \ - outb(0x23, ALI_INDEX) - - -#define ALI_CLOSE() \ - outb(0xbb, ALI_INDEX) - -/* Select a logical device */ -#define ALI_SELDEV(dev) \ - ali_write(0x07, dev) - - -void ali512x_init(void) -{ - ALI_OPEN(); - - ali_write(0x02, 0x01); /* soft reset */ - ali_write(0x03, 0x03); /* disable access to CIOs */ - ali_write(0x22, 0x00); /* disable direct powerdown */ - ali_write(0x23, 0x00); /* disable auto powerdown */ - ali_write(0x24, 0x00); /* IR 8 is active hi, pin26 is PDIR */ - - ALI_CLOSE(); -} - -void ali512x_set_fdc(int enabled, u16 io, u8 irq, u8 dma_channel) -{ - ALI_OPEN(); - ALI_SELDEV(0); - - ali_write(0x30, enabled?1:0); - if (enabled) { - ali_write(0x60, io >> 8); - ali_write(0x61, io & 0xff); - ali_write(0x70, irq); - ali_write(0x74, dma_channel); - - /* AT mode, no drive swap */ - ali_write(0xf0, 0x08); - ali_write(0xf1, 0x00); - ali_write(0xf2, 0xff); - ali_write(0xf4, 0x00); - } - ALI_CLOSE(); -} - - -void ali512x_set_pp(int enabled, u16 io, u8 irq, u8 dma_channel) -{ - ALI_OPEN(); - ALI_SELDEV(3); - - ali_write(0x30, enabled?1:0); - if (enabled) { - ali_write(0x60, io >> 8); - ali_write(0x61, io & 0xff); - ali_write(0x70, irq); - ali_write(0x74, dma_channel); - - /* mode: EPP 1.9, ECP FIFO threshold = 7, IRQ active low */ - ali_write(0xf0, 0xbc); - /* 12 MHz, Burst DMA in ECP */ - ali_write(0xf1, 0x05); - } - ALI_CLOSE(); - -} - -void ali512x_set_uart(int enabled, int index, u16 io, u8 irq) -{ - ALI_OPEN(); - ALI_SELDEV(index?5:4); - - ali_write(0x30, enabled?1:0); - if (enabled) { - ali_write(0x60, io >> 8); - ali_write(0x61, io & 0xff); - ali_write(0x70, irq); - - ali_write(0xf0, 0x00); - ali_write(0xf1, 0x00); - - /* huh? write 0xf2 twice - a typo in rolo - * or some secret ali errata? Who knows? - */ - if (index) { - ali_write(0xf2, 0x00); - } - ali_write(0xf2, 0x0c); - } - ALI_CLOSE(); - -} - -void ali512x_set_uart2_irda(int enabled) -{ - ALI_OPEN(); - ALI_SELDEV(5); - - ali_write(0xf1, enabled?0x48:0x00); /* fullduplex IrDa */ - ALI_CLOSE(); - -} - -void ali512x_set_rtc(int enabled, u16 io, u8 irq) -{ - ALI_OPEN(); - ALI_SELDEV(6); - - ali_write(0x30, enabled?1:0); - if (enabled) { - ali_write(0x60, io >> 8); - ali_write(0x61, io & 0xff); - ali_write(0x70, irq); - - ali_write(0xf0, 0x00); - } - ALI_CLOSE(); -} - -void ali512x_set_kbc(int enabled, u8 kbc_irq, u8 mouse_irq) -{ - ALI_OPEN(); - ALI_SELDEV(7); - - ali_write(0x30, enabled?1:0); - if (enabled) { - ali_write(0x70, kbc_irq); - ali_write(0x72, mouse_irq); - - ali_write(0xf0, 0x00); - } - ALI_CLOSE(); -} - - -/* Common I/O - * - * (This descripotsion is base on several incompete sources - * since I have not been able to obtain any datasheet for the device - * there may be some mis-understandings burried in here. - * -- Daniel daniel@omicron.se) - * - * There are 22 CIO pins numbered - * 10-17 - * 20-25 - * 30-37 - * - * 20-24 are dedicated CIO pins, the other 17 are muliplexed with - * other functions. - * - * Secondary - * CIO Pin Function Decription - * ======================================================= - * CIO10 IRQIN1 Interrupt input 1? - * CIO11 IRQIN2 Interrupt input 2? - * CIO12 IRRX IrDa Receive - * CIO13 IRTX IrDa Transmit - * CIO14 P21 KBC P21 fucntion - * CIO15 P20 KBC P21 fucntion - * CIO16 I2C_CLK I2C Clock - * CIO17 I2C_DAT I2C Data - * - * CIO20 - - * CIO21 - - * CIO22 - - * CIO23 - - * CIO24 - - * CIO25 LOCK Keylock - * - * CIO30 KBC_CLK Keybaord Clock - * CIO31 CS0J General Chip Select decoder CS0J - * CIO32 CS1J General Chip Select decoder CS1J - * CIO33 ALT_KCLK Alternative Keyboard Clock - * CIO34 ALT_KDAT Alternative Keyboard Data - * CIO35 ALT_MCLK Alternative Mouse Clock - * CIO36 ALT_MDAT Alternative Mouse Data - * CIO37 ALT_KBC Alternative KBC select - * - * The CIO use an indirect address scheme. - * - * Reigster 3 in the SIO is used to select the index and data - * port addresses where the CIO I/O registers show up. - * The function selection registers are accessible under - * function SIO 8. - * - * SIO reigster 3 (CIO Address Selection) bit definitions: - * bit 7 CIO index and data registers enabled - * bit 1-0 CIO indirect registers port address select - * 0 index = 0xE0 data = 0xE1 - * 1 index = 0xE2 data = 0xE3 - * 2 index = 0xE4 data = 0xE5 - * 3 index = 0xEA data = 0xEB - * - * There are three CIO I/O register accessed via CIO index port and CIO data port - * 0x01 CIO 10-17 data - * 0x02 CIO 20-25 data (bits 7-6 unused) - * 0x03 CIO 30-37 data - * - * - * The pin function is accessed through normal - * SIO registers, each register have the same format: - * - * Bit Function Value - * 0 Input/output 1=input - * 1 Polarity of signal 1=inverted - * 2 Unused ?? - * 3 Function (normal or special) 1=special - * 7-4 Unused - * - * SIO REG - * 0xe0 CIO 10 Config - * 0xe1 CIO 11 Config - * 0xe2 CIO 12 Config - * 0xe3 CIO 13 Config - * 0xe4 CIO 14 Config - * 0xe5 CIO 15 Config - * 0xe6 CIO 16 Config - * 0xe7 CIO 16 Config - * - * 0xe8 CIO 20 Config - * 0xe9 CIO 21 Config - * 0xea CIO 22 Config - * 0xeb CIO 23 Config - * 0xec CIO 24 Config - * 0xed CIO 25 Config - * - * 0xf5 CIO 30 Config - * 0xf6 CIO 31 Config - * 0xf7 CIO 32 Config - * 0xf8 CIO 33 Config - * 0xf9 CIO 34 Config - * 0xfa CIO 35 Config - * 0xfb CIO 36 Config - * 0xfc CIO 37 Config - * - */ - -#define ALI_CIO_PORT_SEL 0x83 -#define ALI_CIO_INDEX 0xea -#define ALI_CIO_DATA 0xeb - -void ali512x_set_cio(int enabled) -{ - int i; - - ALI_OPEN(); - - if (enabled) { - ali_write(0x3, ALI_CIO_PORT_SEL); /* Enable CIO data register */ - } else { - ali_write(0x3, ALI_CIO_PORT_SEL & ~0x80); - } - - ALI_SELDEV(8); - - ali_write(0x30, enabled?1:0); - - /* set all pins to input to start with */ - for (i=0xe0;i<0xee;i++) { - ali_write(i, 1); - } - - for (i=0xf5;i<0xfe;i++) { - ali_write(i, 1); - } - - ALI_CLOSE(); -} - - -void ali512x_cio_function(int pin, int special, int inv, int input) -{ - u8 data; - u8 addr; - - /* valid pins are 10-17, 20-25 and 30-37 */ - if (pin >= 10 && pin <= 17) { - addr = 0xe0+(pin&7); - } else if (pin >= 20 && pin <= 25) { - addr = 0xe8+(pin&7); - } else if (pin >= 30 && pin <= 37) { - addr = 0xf5+(pin&7); - } else { - return; - } - - ALI_OPEN(); - - ALI_SELDEV(8); - - - data=0xf4; - if (special) { - data |= 0x08; - } else { - if (inv) { - data |= 0x02; - } - if (input) { - data |= 0x01; - } - } - - ali_write(addr, data); - - ALI_CLOSE(); -} - -void ali512x_cio_out(int pin, int value) -{ - u8 reg; - u8 data; - u8 bit; - - reg = pin/10; - bit = 1 << (pin%10); - - - outb(reg, ALI_CIO_INDEX); /* select I/O register */ - data = inb(ALI_CIO_DATA); - if (value) { - data |= bit; - } else { - data &= ~bit; - } - outb(data, ALI_CIO_DATA); -} - -int ali512x_cio_in(int pin) -{ - u8 reg; - u8 data; - u8 bit; - - /* valid pins are 10-17, 20-25 and 30-37 */ - reg = pin/10; - bit = 1 << (pin%10); - - - outb(reg, ALI_CIO_INDEX); /* select I/O register */ - data = inb(ALI_CIO_DATA); - - return data & bit; -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 08/76] sandbox: Drop reference to CONFIG_ARCH_DEVICE_TREE 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (6 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 07/76] misc: Drop ali512x Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 09/76] arm: mvebu: Remove reference to ARMADA_370 Simon Glass ` (64 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used anywhere. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/sandbox/config.mk | 2 -- 1 file changed, 2 deletions(-) diff --git a/arch/sandbox/config.mk b/arch/sandbox/config.mk index 1284ef390b5..2d184c5f652 100644 --- a/arch/sandbox/config.mk +++ b/arch/sandbox/config.mk @@ -44,8 +44,6 @@ cmd_u-boot-spl = (cd $(obj) && $(CC) -o $(SPL_BIN) -Wl,-T u-boot-spl.lds \ -Wl,--no-whole-archive \ $(PLATFORM_LIBS) -Wl,-Map -Wl,u-boot-spl.map -Wl,--gc-sections) -CONFIG_ARCH_DEVICE_TREE := sandbox - ifeq ($(HOST_ARCH),$(HOST_ARCH_X86_64)) EFI_LDS := ${SRCDIR}/../../../arch/x86/lib/elf_x86_64_efi.lds EFI_TARGET := --target=efi-app-x86_64 -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 09/76] arm: mvebu: Remove reference to ARMADA_370 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (7 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 08/76] sandbox: Drop reference to CONFIG_ARCH_DEVICE_TREE Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 10/76] arm: mvebu: Drop reference to CONFIG_ARMADA_39X Simon Glass ` (63 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass Drop this as it is not referenced anywhere else in the code. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v2) Changes in v2: - Just drop the reference arch/arm/mach-mvebu/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile index a23511b113b..28d3e5e1052 100644 --- a/arch/arm/mach-mvebu/Makefile +++ b/arch/arm/mach-mvebu/Makefile @@ -35,7 +35,7 @@ endif extra-y += kwbimage.cfg -ifneq ($(CONFIG_ARMADA_370)$(CONFIG_ARMADA_XP),) +ifneq ($(CONFIG_ARMADA_XP),) KWB_REPLACE += CPU KWB_CFG_CPU = SHEEVA else ifneq ($(CONFIG_ARMADA_375)$(CONFIG_ARMADA_38X)$(CONFIG_ARMADA_39X),) -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 10/76] arm: mvebu: Drop reference to CONFIG_ARMADA_39X 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (8 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 09/76] arm: mvebu: Remove reference to ARMADA_370 Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 11/76] ppc: Drop bat_rw Simon Glass ` (62 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Stefan Roese This is not defined anywhere. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> --- (no changes since v1) arch/arm/mach-mvebu/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile index 28d3e5e1052..a9f506cf2fb 100644 --- a/arch/arm/mach-mvebu/Makefile +++ b/arch/arm/mach-mvebu/Makefile @@ -38,7 +38,7 @@ extra-y += kwbimage.cfg ifneq ($(CONFIG_ARMADA_XP),) KWB_REPLACE += CPU KWB_CFG_CPU = SHEEVA -else ifneq ($(CONFIG_ARMADA_375)$(CONFIG_ARMADA_38X)$(CONFIG_ARMADA_39X),) +else ifneq ($(CONFIG_ARMADA_375)$(CONFIG_ARMADA_38X),) KWB_REPLACE += CPU KWB_CFG_CPU = A9 endif -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 11/76] ppc: Drop bat_rw 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (9 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 10/76] arm: mvebu: Drop reference to CONFIG_ARMADA_39X Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 12/76] rockchip: Correct a reference to CONFIG_BOOT_MODE_REG Simon Glass ` (61 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot Cc: Tom Rini, Simon Glass, Andy Fleming, Mario Six, Priyanka Jain, Stefan Roese, Wolfgang Denk Drop this unused driver. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/powerpc/lib/Makefile | 1 - arch/powerpc/lib/bat_rw.c | 244 -------------------------------------- 2 files changed, 245 deletions(-) delete mode 100644 arch/powerpc/lib/bat_rw.c diff --git a/arch/powerpc/lib/Makefile b/arch/powerpc/lib/Makefile index 066d7f408e0..bb819dcbb6c 100644 --- a/arch/powerpc/lib/Makefile +++ b/arch/powerpc/lib/Makefile @@ -34,7 +34,6 @@ obj-y += ticks.o endif obj-y += reloc.o -obj-$(CONFIG_BAT_RW) += bat_rw.o obj-$(CONFIG_CMD_BOOTM) += bootm.o obj-y += cache.o obj-y += extable.o diff --git a/arch/powerpc/lib/bat_rw.c b/arch/powerpc/lib/bat_rw.c deleted file mode 100644 index 24dd30615bd..00000000000 --- a/arch/powerpc/lib/bat_rw.c +++ /dev/null @@ -1,244 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2002 - * Rich Ireland, Enterasys Networks, rireland@enterasys.com. - */ - -#include <common.h> -#include <asm/global_data.h> -#include <asm/processor.h> -#include <asm/mmu.h> -#include <asm/io.h> -#include <linux/compiler.h> - -#ifdef CONFIG_ADDR_MAP -#include <addr_map.h> -#endif - -DECLARE_GLOBAL_DATA_PTR; - -int write_bat (ppc_bat_t bat, unsigned long upper, unsigned long lower) -{ - __maybe_unused int batn = -1; - - sync(); - - switch (bat) { - case DBAT0: - mtspr (DBAT0L, lower); - mtspr (DBAT0U, upper); - batn = 0; - break; - case IBAT0: - mtspr (IBAT0L, lower); - mtspr (IBAT0U, upper); - break; - case DBAT1: - mtspr (DBAT1L, lower); - mtspr (DBAT1U, upper); - batn = 1; - break; - case IBAT1: - mtspr (IBAT1L, lower); - mtspr (IBAT1U, upper); - break; - case DBAT2: - mtspr (DBAT2L, lower); - mtspr (DBAT2U, upper); - batn = 2; - break; - case IBAT2: - mtspr (IBAT2L, lower); - mtspr (IBAT2U, upper); - break; - case DBAT3: - mtspr (DBAT3L, lower); - mtspr (DBAT3U, upper); - batn = 3; - break; - case IBAT3: - mtspr (IBAT3L, lower); - mtspr (IBAT3U, upper); - break; -#ifdef CONFIG_HIGH_BATS - case DBAT4: - mtspr (DBAT4L, lower); - mtspr (DBAT4U, upper); - batn = 4; - break; - case IBAT4: - mtspr (IBAT4L, lower); - mtspr (IBAT4U, upper); - break; - case DBAT5: - mtspr (DBAT5L, lower); - mtspr (DBAT5U, upper); - batn = 5; - break; - case IBAT5: - mtspr (IBAT5L, lower); - mtspr (IBAT5U, upper); - break; - case DBAT6: - mtspr (DBAT6L, lower); - mtspr (DBAT6U, upper); - batn = 6; - break; - case IBAT6: - mtspr (IBAT6L, lower); - mtspr (IBAT6U, upper); - break; - case DBAT7: - mtspr (DBAT7L, lower); - mtspr (DBAT7U, upper); - batn = 7; - break; - case IBAT7: - mtspr (IBAT7L, lower); - mtspr (IBAT7U, upper); - break; -#endif - default: - return (-1); - } - -#ifdef CONFIG_ADDR_MAP - if ((gd->flags & GD_FLG_RELOC) && (batn >= 0)) { - phys_size_t size; - if (!BATU_VALID(upper)) - size = 0; - else - size = BATU_SIZE(upper); - addrmap_set_entry(BATU_VADDR(upper), BATL_PADDR(lower), - size, batn); - } -#endif - - sync(); - isync(); - - return (0); -} - -int read_bat (ppc_bat_t bat, unsigned long *upper, unsigned long *lower) -{ - unsigned long register u; - unsigned long register l; - - switch (bat) { - case DBAT0: - l = mfspr (DBAT0L); - u = mfspr (DBAT0U); - break; - case IBAT0: - l = mfspr (IBAT0L); - u = mfspr (IBAT0U); - break; - case DBAT1: - l = mfspr (DBAT1L); - u = mfspr (DBAT1U); - break; - case IBAT1: - l = mfspr (IBAT1L); - u = mfspr (IBAT1U); - break; - case DBAT2: - l = mfspr (DBAT2L); - u = mfspr (DBAT2U); - break; - case IBAT2: - l = mfspr (IBAT2L); - u = mfspr (IBAT2U); - break; - case DBAT3: - l = mfspr (DBAT3L); - u = mfspr (DBAT3U); - break; - case IBAT3: - l = mfspr (IBAT3L); - u = mfspr (IBAT3U); - break; -#ifdef CONFIG_HIGH_BATS - case DBAT4: - l = mfspr (DBAT4L); - u = mfspr (DBAT4U); - break; - case IBAT4: - l = mfspr (IBAT4L); - u = mfspr (IBAT4U); - break; - case DBAT5: - l = mfspr (DBAT5L); - u = mfspr (DBAT5U); - break; - case IBAT5: - l = mfspr (IBAT5L); - u = mfspr (IBAT5U); - break; - case DBAT6: - l = mfspr (DBAT6L); - u = mfspr (DBAT6U); - break; - case IBAT6: - l = mfspr (IBAT6L); - u = mfspr (IBAT6U); - break; - case DBAT7: - l = mfspr (DBAT7L); - u = mfspr (DBAT7U); - break; - case IBAT7: - l = mfspr (IBAT7L); - u = mfspr (IBAT7U); - break; -#endif - default: - return (-1); - } - - *upper = u; - *lower = l; - - return (0); -} - -void print_bats(void) -{ - printf("BAT registers:\n"); - - printf ("\tIBAT0L = 0x%08X ", mfspr (IBAT0L)); - printf ("\tIBAT0U = 0x%08X\n", mfspr (IBAT0U)); - printf ("\tDBAT0L = 0x%08X ", mfspr (DBAT0L)); - printf ("\tDBAT0U = 0x%08X\n", mfspr (DBAT0U)); - printf ("\tIBAT1L = 0x%08X ", mfspr (IBAT1L)); - printf ("\tIBAT1U = 0x%08X\n", mfspr (IBAT1U)); - printf ("\tDBAT1L = 0x%08X ", mfspr (DBAT1L)); - printf ("\tDBAT1U = 0x%08X\n", mfspr (DBAT1U)); - printf ("\tIBAT2L = 0x%08X ", mfspr (IBAT2L)); - printf ("\tIBAT2U = 0x%08X\n", mfspr (IBAT2U)); - printf ("\tDBAT2L = 0x%08X ", mfspr (DBAT2L)); - printf ("\tDBAT2U = 0x%08X\n", mfspr (DBAT2U)); - printf ("\tIBAT3L = 0x%08X ", mfspr (IBAT3L)); - printf ("\tIBAT3U = 0x%08X\n", mfspr (IBAT3U)); - printf ("\tDBAT3L = 0x%08X ", mfspr (DBAT3L)); - printf ("\tDBAT3U = 0x%08X\n", mfspr (DBAT3U)); - -#ifdef CONFIG_HIGH_BATS - printf ("\tIBAT4L = 0x%08X ", mfspr (IBAT4L)); - printf ("\tIBAT4U = 0x%08X\n", mfspr (IBAT4U)); - printf ("\tDBAT4L = 0x%08X ", mfspr (DBAT4L)); - printf ("\tDBAT4U = 0x%08X\n", mfspr (DBAT4U)); - printf ("\tIBAT5L = 0x%08X ", mfspr (IBAT5L)); - printf ("\tIBAT5U = 0x%08X\n", mfspr (IBAT5U)); - printf ("\tDBAT5L = 0x%08X ", mfspr (DBAT5L)); - printf ("\tDBAT5U = 0x%08X\n", mfspr (DBAT5U)); - printf ("\tIBAT6L = 0x%08X ", mfspr (IBAT6L)); - printf ("\tIBAT6U = 0x%08X\n", mfspr (IBAT6U)); - printf ("\tDBAT6L = 0x%08X ", mfspr (DBAT6L)); - printf ("\tDBAT6U = 0x%08X\n", mfspr (DBAT6U)); - printf ("\tIBAT7L = 0x%08X ", mfspr (IBAT7L)); - printf ("\tIBAT7U = 0x%08X\n", mfspr (IBAT7U)); - printf ("\tDBAT7L = 0x%08X ", mfspr (DBAT7L)); - printf ("\tDBAT7U = 0x%08X\n", mfspr (DBAT7U)); -#endif -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 12/76] rockchip: Correct a reference to CONFIG_BOOT_MODE_REG 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (10 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 11/76] ppc: Drop bat_rw Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 13/76] cmd: Add an option to enable the ini command Simon Glass ` (60 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Kever Yang, Philipp Tomsich This option does not exist and should refer to CONFIG_ROCKCHIP_BOOT_MODE_REG instead. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/arm/mach-rockchip/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-rockchip/Makefile b/arch/arm/mach-rockchip/Makefile index 32138fa723f..e3d4a8b42e4 100644 --- a/arch/arm/mach-rockchip/Makefile +++ b/arch/arm/mach-rockchip/Makefile @@ -18,7 +18,7 @@ obj-spl-$(CONFIG_ROCKCHIP_RK3036) += rk3036-board-spl.o ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_TPL_BUILD),) # Always include boot_mode.o, as we bypass it (i.e. turn it off) -# inside of boot_mode.c when CONFIG_BOOT_MODE_REG is 0. This way, +# inside of boot_mode.c when CONFIG_ROCKCHIP_BOOT_MODE_REG is 0. This way, # we can have the preprocessor correctly recognise both 0x0 and 0 # meaning "turn it off". obj-y += boot_mode.o -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 13/76] cmd: Add an option to enable the ini command 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (11 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 12/76] rockchip: Correct a reference to CONFIG_BOOT_MODE_REG Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 14/76] cmd: Drop mfsl command Simon Glass ` (59 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This command has no Kconfig option at present, but seems useful enough to keep around. Add one. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) cmd/Kconfig | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/cmd/Kconfig b/cmd/Kconfig index 4fe2c75de25..b697469a4cb 100644 --- a/cmd/Kconfig +++ b/cmd/Kconfig @@ -2015,6 +2015,13 @@ config CMD_LED with led on/off/togle/blink. Any LED drivers can be controlled with this command, e.g. led_gpio. +config CMD_INI + bool "ini" + help + Enable the 'ini' command which allows a .ini file to be parsed and + placed into environment variables. Please check the source code for + this as there is no documentation. + config CMD_DATE bool "date" default y if DM_RTC -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 14/76] cmd: Drop mfsl command 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (12 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 13/76] cmd: Add an option to enable the ini command Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 15/76] Correct CONFIG_CONTROLCENTERDC Simon Glass ` (58 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used anywhere. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) cmd/Makefile | 1 - cmd/mfsl.c | 387 --------------------------------------------------- 2 files changed, 388 deletions(-) delete mode 100644 cmd/mfsl.c diff --git a/cmd/Makefile b/cmd/Makefile index 0b6a96c1d91..4adc7530a0a 100644 --- a/cmd/Makefile +++ b/cmd/Makefile @@ -108,7 +108,6 @@ obj-$(CONFIG_ID_EEPROM) += mac.o obj-$(CONFIG_CMD_MD5SUM) += md5sum.o obj-$(CONFIG_CMD_MEMORY) += mem.o obj-$(CONFIG_CMD_IO) += io.o -obj-$(CONFIG_CMD_MFSL) += mfsl.o obj-$(CONFIG_CMD_MII) += mii.o obj-$(CONFIG_CMD_MISC) += misc.o obj-$(CONFIG_CMD_MDIO) += mdio.o diff --git a/cmd/mfsl.c b/cmd/mfsl.c deleted file mode 100644 index 0c78720ec46..00000000000 --- a/cmd/mfsl.c +++ /dev/null @@ -1,387 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2007 Michal Simek - * - * Michal SIMEK <monstr@monstr.eu> - */ - -/* - * Microblaze FSL support - */ - -#include <common.h> -#include <config.h> -#include <command.h> -#include <asm/asm.h> - -int do_frd(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[]) -{ - unsigned int fslnum; - unsigned int num; - unsigned int blocking; - - if (argc < 2) - return CMD_RET_USAGE; - - fslnum = (unsigned int)hextoul(argv[1], NULL); - blocking = (unsigned int)hextoul(argv[2], NULL); - if (fslnum < 0 || fslnum >= XILINX_FSL_NUMBER) { - puts ("Bad number of FSL\n"); - return CMD_RET_USAGE; - } - - switch (fslnum) { -#if (XILINX_FSL_NUMBER > 0) - case 0: - switch (blocking) { - case 0: NGET (num, 0); - break; - case 1: NCGET (num, 0); - break; - case 2: GET (num, 0); - break; - case 3: CGET (num, 0); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 1) - case 1: - switch (blocking) { - case 0: NGET (num, 1); - break; - case 1: NCGET (num, 1); - break; - case 2: GET (num, 1); - break; - case 3: CGET (num, 1); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 2) - case 2: - switch (blocking) { - case 0: NGET (num, 2); - break; - case 1: NCGET (num, 2); - break; - case 2: GET (num, 2); - break; - case 3: CGET (num, 2); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 3) - case 3: - switch (blocking) { - case 0: NGET (num, 3); - break; - case 1: NCGET (num, 3); - break; - case 2: GET (num, 3); - break; - case 3: CGET (num, 3); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 4) - case 4: - switch (blocking) { - case 0: NGET (num, 4); - break; - case 1: NCGET (num, 4); - break; - case 2: GET (num, 4); - break; - case 3: CGET (num, 4); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 5) - case 5: - switch (blocking) { - case 0: NGET (num, 5); - break; - case 1: NCGET (num, 5); - break; - case 2: GET (num, 5); - break; - case 3: CGET (num, 5); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 6) - case 6: - switch (blocking) { - case 0: NGET (num, 6); - break; - case 1: NCGET (num, 6); - break; - case 2: GET (num, 6); - break; - case 3: CGET (num, 6); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 7) - case 7: - switch (blocking) { - case 0: NGET (num, 7); - break; - case 1: NCGET (num, 7); - break; - case 2: GET (num, 7); - break; - case 3: CGET (num, 7); - break; - default: - return 2; - } - break; -#endif - default: - return 1; - } - - printf ("%01x: 0x%08x - %s %s read\n", fslnum, num, - blocking < 2 ? "non blocking" : "blocking", - ((blocking == 1) || (blocking == 3)) ? "control" : "data" ); - return 0; -} - -int do_fwr(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[]) -{ - unsigned int fslnum; - unsigned int num; - unsigned int blocking; - - if (argc < 3) - return CMD_RET_USAGE; - - fslnum = (unsigned int)hextoul(argv[1], NULL); - num = (unsigned int)hextoul(argv[2], NULL); - blocking = (unsigned int)hextoul(argv[3], NULL); - if (fslnum < 0 || fslnum >= XILINX_FSL_NUMBER) - return CMD_RET_USAGE; - - switch (fslnum) { -#if (XILINX_FSL_NUMBER > 0) - case 0: - switch (blocking) { - case 0: NPUT (num, 0); - break; - case 1: NCPUT (num, 0); - break; - case 2: PUT (num, 0); - break; - case 3: CPUT (num, 0); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 1) - case 1: - switch (blocking) { - case 0: NPUT (num, 1); - break; - case 1: NCPUT (num, 1); - break; - case 2: PUT (num, 1); - break; - case 3: CPUT (num, 1); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 2) - case 2: - switch (blocking) { - case 0: NPUT (num, 2); - break; - case 1: NCPUT (num, 2); - break; - case 2: PUT (num, 2); - break; - case 3: CPUT (num, 2); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 3) - case 3: - switch (blocking) { - case 0: NPUT (num, 3); - break; - case 1: NCPUT (num, 3); - break; - case 2: PUT (num, 3); - break; - case 3: CPUT (num, 3); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 4) - case 4: - switch (blocking) { - case 0: NPUT (num, 4); - break; - case 1: NCPUT (num, 4); - break; - case 2: PUT (num, 4); - break; - case 3: CPUT (num, 4); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 5) - case 5: - switch (blocking) { - case 0: NPUT (num, 5); - break; - case 1: NCPUT (num, 5); - break; - case 2: PUT (num, 5); - break; - case 3: CPUT (num, 5); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 6) - case 6: - switch (blocking) { - case 0: NPUT (num, 6); - break; - case 1: NCPUT (num, 6); - break; - case 2: PUT (num, 6); - break; - case 3: CPUT (num, 6); - break; - default: - return 2; - } - break; -#endif -#if (XILINX_FSL_NUMBER > 7) - case 7: - switch (blocking) { - case 0: NPUT (num, 7); - break; - case 1: NCPUT (num, 7); - break; - case 2: PUT (num, 7); - break; - case 3: CPUT (num, 7); - break; - default: - return 2; - } - break; -#endif - default: - return 1; - } - - printf ("%01x: 0x%08x - %s %s write\n", fslnum, num, - blocking < 2 ? "non blocking" : "blocking", - ((blocking == 1) || (blocking == 3)) ? "control" : "data" ); - return 0; - -} - -int do_rspr(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[]) -{ - unsigned int reg = 0; - unsigned int val = 0; - - if (argc < 2) - return CMD_RET_USAGE; - - reg = (unsigned int)hextoul(argv[1], NULL); - val = (unsigned int)hextoul(argv[2], NULL); - switch (reg) { - case 0x1: - if (argc > 2) { - MTS (val, rmsr); - NOP; - MFS (val, rmsr); - } else { - MFS (val, rmsr); - } - puts ("MSR"); - break; - case 0x3: - MFS (val, rear); - puts ("EAR"); - break; - case 0x5: - MFS (val, resr); - puts ("ESR"); - break; - default: - puts ("Unsupported register\n"); - return 1; - } - printf (": 0x%08x\n", val); - return 0; -} - -/***************************************************/ - -U_BOOT_CMD (frd, 3, 1, do_frd, - "read data from FSL", - "- [fslnum [0|1|2|3]]\n" - " 0 - non blocking data read\n" - " 1 - non blocking control read\n" - " 2 - blocking data read\n" - " 3 - blocking control read"); - -U_BOOT_CMD (fwr, 4, 1, do_fwr, - "write data to FSL", - "- [fslnum [0|1|2|3]]\n" - " 0 - non blocking data write\n" - " 1 - non blocking control write\n" - " 2 - blocking data write\n" - " 3 - blocking control write"); - -U_BOOT_CMD (rspr, 3, 1, do_rspr, - "read/write special purpose register", - "- reg_num [write value] read/write special purpose register\n" - " 1 - MSR - Machine status register\n" - " 3 - EAR - Exception address register\n" - " 5 - ESR - Exception status register"); -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 15/76] Correct CONFIG_CONTROLCENTERDC 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (13 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 14/76] cmd: Drop mfsl command Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 16/76] Drop dataflash_mmc_mux command Simon Glass ` (57 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This option does not exist but presumably means to point to CONFIG_TARGET_CONTROLCENTERDC. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) board/gdsys/common/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/board/gdsys/common/Makefile b/board/gdsys/common/Makefile index dd6d5e69de5..553e2ca50ed 100644 --- a/board/gdsys/common/Makefile +++ b/board/gdsys/common/Makefile @@ -5,7 +5,7 @@ obj-$(CONFIG_SYS_FPGA_COMMON) += fpga.o obj-$(CONFIG_CMD_IOLOOP) += cmd_ioloop.o -obj-$(CONFIG_CONTROLCENTERD) += dp501.o +obj-$(CONFIG_TARGET_CONTROLCENTERDC) += dp501.o obj-$(CONFIG_TARGET_GAZERBEAM) += osd.o ihs_mdio.o ioep-fpga.o ifdef CONFIG_OSD -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 16/76] Drop dataflash_mmc_mux command 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (14 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 15/76] Correct CONFIG_CONTROLCENTERDC Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-06 0:29 ` Jaehoon Chung 2023-02-01 20:19 ` [PATCH v3 17/76] Drop CONFIG_DM644X_GPIO Simon Glass ` (56 subsequent siblings) 72 siblings, 1 reply; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) cmd/Makefile | 1 - cmd/dataflash_mmc_mux.c | 48 ----------------------------------------- 2 files changed, 49 deletions(-) delete mode 100644 cmd/dataflash_mmc_mux.c diff --git a/cmd/Makefile b/cmd/Makefile index 4adc7530a0a..b6888a52f49 100644 --- a/cmd/Makefile +++ b/cmd/Makefile @@ -47,7 +47,6 @@ obj-$(CONFIG_CMD_CONFIG) += config.o obj-$(CONFIG_CMD_CONITRACE) += conitrace.o obj-$(CONFIG_CMD_CONSOLE) += console.o obj-$(CONFIG_CMD_CPU) += cpu.o -obj-$(CONFIG_DATAFLASH_MMC_SELECT) += dataflash_mmc_mux.o obj-$(CONFIG_CMD_DATE) += date.o obj-$(CONFIG_CMD_DEMO) += demo.o obj-$(CONFIG_CMD_DM) += dm.o diff --git a/cmd/dataflash_mmc_mux.c b/cmd/dataflash_mmc_mux.c deleted file mode 100644 index 73876e9464a..00000000000 --- a/cmd/dataflash_mmc_mux.c +++ /dev/null @@ -1,48 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -#include <common.h> -#include <command.h> - -static int mmc_nspi (const char *); - -int do_dataflash_mmc_mux(struct cmd_tbl *cmdtp, int flag, int argc, - char *const argv[]) -{ - switch (argc) { - case 2: /* on / off */ - switch (mmc_nspi (argv[1])) { - case 0: AT91F_SelectSPI (); - break; - case 1: AT91F_SelectMMC (); - break; - } - case 1: /* get status */ - printf ("Mux is configured to be %s\n", - AT91F_GetMuxStatus () ? "MMC" : "SPI"); - return 0; - default: - return CMD_RET_USAGE; - } - return 0; -} - -static int mmc_nspi (const char *s) -{ - if (strcmp (s, "mmc") == 0) { - return 1; - } else if (strcmp (s, "spi") == 0) { - return 0; - } - return -1; -} - -U_BOOT_CMD( - dataflash_mmc_mux, 2, 1, do_dataflash_mmc_mux, - "enable or disable MMC or SPI\n", - "[mmc, spi]\n" - " - enable or disable MMC or SPI" -); -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* RE: [PATCH v3 16/76] Drop dataflash_mmc_mux command 2023-02-01 20:19 ` [PATCH v3 16/76] Drop dataflash_mmc_mux command Simon Glass @ 2023-02-06 0:29 ` Jaehoon Chung 0 siblings, 0 replies; 87+ messages in thread From: Jaehoon Chung @ 2023-02-06 0:29 UTC (permalink / raw) To: 'Simon Glass', u-boot; +Cc: 'Tom Rini' > -----Original Message----- > From: U-Boot <u-boot-bounces@lists.denx.de> On Behalf Of Simon Glass > Sent: Thursday, February 2, 2023 5:19 AM > To: u-boot@lists.denx.de > Cc: Tom Rini <trini@konsulko.com>; Simon Glass <sjg@chromium.org> > Subject: [PATCH v3 16/76] Drop dataflash_mmc_mux command > > This is not used. Drop it. > > Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Best Regards, Jaehoon Chung > --- > > (no changes since v1) > > cmd/Makefile | 1 - > cmd/dataflash_mmc_mux.c | 48 ----------------------------------------- > 2 files changed, 49 deletions(-) > delete mode 100644 cmd/dataflash_mmc_mux.c > > diff --git a/cmd/Makefile b/cmd/Makefile > index 4adc7530a0a..b6888a52f49 100644 > --- a/cmd/Makefile > +++ b/cmd/Makefile > @@ -47,7 +47,6 @@ obj-$(CONFIG_CMD_CONFIG) += config.o > obj-$(CONFIG_CMD_CONITRACE) += conitrace.o > obj-$(CONFIG_CMD_CONSOLE) += console.o > obj-$(CONFIG_CMD_CPU) += cpu.o > -obj-$(CONFIG_DATAFLASH_MMC_SELECT) += dataflash_mmc_mux.o > obj-$(CONFIG_CMD_DATE) += date.o > obj-$(CONFIG_CMD_DEMO) += demo.o > obj-$(CONFIG_CMD_DM) += dm.o > diff --git a/cmd/dataflash_mmc_mux.c b/cmd/dataflash_mmc_mux.c > deleted file mode 100644 > index 73876e9464a..00000000000 > --- a/cmd/dataflash_mmc_mux.c > +++ /dev/null > @@ -1,48 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0+ > -/* > - * (C) Copyright 2000 > - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. > - */ > - > -#include <common.h> > -#include <command.h> > - > -static int mmc_nspi (const char *); > - > -int do_dataflash_mmc_mux(struct cmd_tbl *cmdtp, int flag, int argc, > - char *const argv[]) > -{ > - switch (argc) { > - case 2: /* on / off */ > - switch (mmc_nspi (argv[1])) { > - case 0: AT91F_SelectSPI (); > - break; > - case 1: AT91F_SelectMMC (); > - break; > - } > - case 1: /* get status */ > - printf ("Mux is configured to be %s\n", > - AT91F_GetMuxStatus () ? "MMC" : "SPI"); > - return 0; > - default: > - return CMD_RET_USAGE; > - } > - return 0; > -} > - > -static int mmc_nspi (const char *s) > -{ > - if (strcmp (s, "mmc") == 0) { > - return 1; > - } else if (strcmp (s, "spi") == 0) { > - return 0; > - } > - return -1; > -} > - > -U_BOOT_CMD( > - dataflash_mmc_mux, 2, 1, do_dataflash_mmc_mux, > - "enable or disable MMC or SPI\n", > - "[mmc, spi]\n" > - " - enable or disable MMC or SPI" > -); > -- > 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply [flat|nested] 87+ messages in thread
* [PATCH v3 17/76] Drop CONFIG_DM644X_GPIO 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (15 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 16/76] Drop dataflash_mmc_mux command Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 18/76] Makefile: Avoid use of invalid CONFIG_ option Simon Glass ` (55 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass Drop this unused option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/gpio/Makefile | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 57603645c1c..07fca7bd33d 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -38,7 +38,6 @@ obj-$(CONFIG_SANDBOX_GPIO) += sandbox.o sandbox_test.o obj-$(CONFIG_TEGRA_GPIO) += tegra_gpio.o obj-$(CONFIG_TEGRA186_GPIO) += tegra186_gpio.o obj-$(CONFIG_DA8XX_GPIO) += da8xx_gpio.o -obj-$(CONFIG_DM644X_GPIO) += da8xx_gpio.o obj-$(CONFIG_ALTERA_PIO) += altera_pio.o obj-$(CONFIG_MPC83XX_GPIO) += mpc83xx_gpio.o obj-$(CONFIG_MPC8XXX_GPIO) += mpc8xxx_gpio.o -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 18/76] Makefile: Avoid use of invalid CONFIG_ option 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (16 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 17/76] Drop CONFIG_DM644X_GPIO Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 19/76] env: Drop ENV_IS_IN_SATA Simon Glass ` (54 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This appears in a comment but is not a real option. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index c9d6d67310d..2648fd5d8f9 100644 --- a/Makefile +++ b/Makefile @@ -1082,7 +1082,7 @@ expect = $(foreach cfg,$(1),y) # Show a deprecation message # Args: -# 1: List of CONFIG_DM_... to migrate to (e.g. "CONFIG_DM_MMC CONFIG_BLK") +# 1: List of options to migrate to (e.g. "CONFIG_DM_MMC CONFIG_BLK") # 2: Name of component (e.g . "Ethernet drivers") # 3: Release deadline (e.g. "v202.07") # 4: Condition to require before checking (e.g. "$(CONFIG_NET)") -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 19/76] env: Drop ENV_IS_IN_SATA 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (17 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 18/76] Makefile: Avoid use of invalid CONFIG_ option Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 20/76] samsung: Drop CONFIG_EXYNOS_PWM_BL Simon Glass ` (53 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used anywhere, so drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) cmd/nvedit.c | 1 - env/Makefile | 1 - env/env.c | 3 -- env/sata.c | 122 --------------------------------------------------- 4 files changed, 127 deletions(-) delete mode 100644 env/sata.c diff --git a/cmd/nvedit.c b/cmd/nvedit.c index 53e6b57b60e..e2a5f0089e9 100644 --- a/cmd/nvedit.c +++ b/cmd/nvedit.c @@ -51,7 +51,6 @@ DECLARE_GLOBAL_DATA_PTR; defined(CONFIG_ENV_IS_IN_NAND) || \ defined(CONFIG_ENV_IS_IN_NVRAM) || \ defined(CONFIG_ENV_IS_IN_ONENAND) || \ - defined(CONFIG_ENV_IS_IN_SATA) || \ defined(CONFIG_ENV_IS_IN_SPI_FLASH) || \ defined(CONFIG_ENV_IS_IN_REMOTE) || \ defined(CONFIG_ENV_IS_IN_UBI) diff --git a/env/Makefile b/env/Makefile index bb6e24b396d..673b979fdfa 100644 --- a/env/Makefile +++ b/env/Makefile @@ -16,7 +16,6 @@ extra-$(CONFIG_ENV_IS_IN_FLASH) += embedded.o obj-$(CONFIG_ENV_IS_IN_NVRAM) += embedded.o obj-$(CONFIG_ENV_IS_IN_NVRAM) += nvram.o obj-$(CONFIG_ENV_IS_IN_ONENAND) += onenand.o -obj-$(CONFIG_ENV_IS_IN_SATA) += sata.o obj-$(CONFIG_ENV_IS_IN_REMOTE) += remote.o obj-$(CONFIG_ENV_IS_IN_UBI) += ubi.o endif diff --git a/env/env.c b/env/env.c index 06078c7f374..0f73ebc08e0 100644 --- a/env/env.c +++ b/env/env.c @@ -78,9 +78,6 @@ static enum env_location env_locations[] = { #ifdef CONFIG_ENV_IS_IN_REMOTE ENVL_REMOTE, #endif -#ifdef CONFIG_ENV_IS_IN_SATA - ENVL_ESATA, -#endif #ifdef CONFIG_ENV_IS_IN_SPI_FLASH ENVL_SPI_FLASH, #endif diff --git a/env/sata.c b/env/sata.c deleted file mode 100644 index 9442cfcaf3c..00000000000 --- a/env/sata.c +++ /dev/null @@ -1,122 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2010-2016 Freescale Semiconductor, Inc. - */ - -/* #define DEBUG */ - -#include <common.h> - -#include <command.h> -#include <env.h> -#include <env_internal.h> -#include <linux/stddef.h> -#include <errno.h> -#include <memalign.h> -#include <sata.h> -#include <search.h> - -#if defined(CONFIG_ENV_OFFSET_REDUND) -#error ENV REDUND not supported -#endif - -#if !defined(CONFIG_ENV_OFFSET) || !defined(CONFIG_ENV_SIZE) -#error CONFIG_ENV_OFFSET or CONFIG_ENV_SIZE not defined -#endif - -__weak int sata_get_env_dev(void) -{ - return CONFIG_SYS_SATA_ENV_DEV; -} - -#ifdef CONFIG_CMD_SAVEENV -static inline int write_env(struct blk_desc *sata, unsigned long size, - unsigned long offset, void *buffer) -{ - uint blk_start, blk_cnt, n; - - blk_start = ALIGN(offset, sata->blksz) / sata->blksz; - blk_cnt = ALIGN(size, sata->blksz) / sata->blksz; - - n = blk_dwrite(sata, blk_start, blk_cnt, buffer); - - return (n == blk_cnt) ? 0 : -1; -} - -static int env_sata_save(void) -{ - ALLOC_CACHE_ALIGN_BUFFER(env_t, env_new, 1); - struct blk_desc *sata = NULL; - int env_sata, ret; - - if (sata_initialize()) - return 1; - - env_sata = sata_get_env_dev(); - - sata = sata_get_dev(env_sata); - if (sata == NULL) { - printf("Unknown SATA(%d) device for environment!\n", - env_sata); - return 1; - } - - ret = env_export(env_new); - if (ret) - return 1; - - printf("Writing to SATA(%d)...", env_sata); - if (write_env(sata, CONFIG_ENV_SIZE, CONFIG_ENV_OFFSET, (u_char *)env_new)) { - puts("failed\n"); - return 1; - } - - puts("done\n"); - return 0; -} -#endif /* CONFIG_CMD_SAVEENV */ - -static inline int read_env(struct blk_desc *sata, unsigned long size, - unsigned long offset, void *buffer) -{ - uint blk_start, blk_cnt, n; - - blk_start = ALIGN(offset, sata->blksz) / sata->blksz; - blk_cnt = ALIGN(size, sata->blksz) / sata->blksz; - - n = blk_dread(sata, blk_start, blk_cnt, buffer); - - return (n == blk_cnt) ? 0 : -1; -} - -static void env_sata_load(void) -{ - ALLOC_CACHE_ALIGN_BUFFER(char, buf, CONFIG_ENV_SIZE); - struct blk_desc *sata = NULL; - int env_sata; - - if (sata_initialize()) - return -EIO; - - env_sata = sata_get_env_dev(); - - sata = sata_get_dev(env_sata); - if (sata == NULL) { - printf("Unknown SATA(%d) device for environment!\n", env_sata); - return -EIO; - } - - if (read_env(sata, CONFIG_ENV_SIZE, CONFIG_ENV_OFFSET, buf)) { - env_set_default(NULL, 0); - return -EIO; - } - - return env_import(buf, 1, H_EXTERNAL); -} - -U_BOOT_ENV_LOCATION(sata) = { - .location = ENVL_ESATA, - ENV_NAME("SATA") - .load = env_sata_load, - .save = env_save_ptr(env_sata_save), -}; -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 20/76] samsung: Drop CONFIG_EXYNOS_PWM_BL 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (18 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 19/76] env: Drop ENV_IS_IN_SATA Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-03 6:05 ` Minkyu Kang 2023-02-01 20:19 ` [PATCH v3 21/76] fpga: Add a LATTICE option Simon Glass ` (52 subsequent siblings) 72 siblings, 1 reply; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Minkyu Kang This is not defined anywhere. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/video/exynos/Makefile | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/video/exynos/Makefile b/drivers/video/exynos/Makefile index 0f58954e49c..45067f562cb 100644 --- a/drivers/video/exynos/Makefile +++ b/drivers/video/exynos/Makefile @@ -7,4 +7,3 @@ obj-$(CONFIG_EXYNOS_DP) += exynos_dp.o exynos_dp_lowlevel.o obj-$(CONFIG_EXYNOS_FB) += exynos_fb.o obj-$(CONFIG_EXYNOS_MIPI_DSIM) += exynos_mipi_dsi.o exynos_mipi_dsi_common.o \ exynos_mipi_dsi_lowlevel.o -obj-$(CONFIG_EXYNOS_PWM_BL) += exynos_pwm_bl.o -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* Re: [PATCH v3 20/76] samsung: Drop CONFIG_EXYNOS_PWM_BL 2023-02-01 20:19 ` [PATCH v3 20/76] samsung: Drop CONFIG_EXYNOS_PWM_BL Simon Glass @ 2023-02-03 6:05 ` Minkyu Kang 0 siblings, 0 replies; 87+ messages in thread From: Minkyu Kang @ 2023-02-03 6:05 UTC (permalink / raw) To: Simon Glass; +Cc: u-boot, Tom Rini, Minkyu Kang Hi, On Thu, 2 Feb 2023 at 05:34, Simon Glass <sjg@chromium.org> wrote: > This is not defined anywhere. Drop it. > > Signed-off-by: Simon Glass <sjg@chromium.org> > --- > > (no changes since v1) > > drivers/video/exynos/Makefile | 1 - > 1 file changed, 1 deletion(-) > > diff --git a/drivers/video/exynos/Makefile b/drivers/video/exynos/Makefile > index 0f58954e49c..45067f562cb 100644 > --- a/drivers/video/exynos/Makefile > +++ b/drivers/video/exynos/Makefile > @@ -7,4 +7,3 @@ obj-$(CONFIG_EXYNOS_DP) += exynos_dp.o exynos_dp_lowlevel.o > obj-$(CONFIG_EXYNOS_FB) += exynos_fb.o > obj-$(CONFIG_EXYNOS_MIPI_DSIM) += exynos_mipi_dsi.o > exynos_mipi_dsi_common.o \ > exynos_mipi_dsi_lowlevel.o > -obj-$(CONFIG_EXYNOS_PWM_BL) += exynos_pwm_bl.o > -- > 2.39.1.456.gfc5497dd1b-goog > > Reviewed-by: Minkyu Kang <mk7.kang@samsung.com> -- Thanks, Minkyu Kang. ^ permalink raw reply [flat|nested] 87+ messages in thread
* [PATCH v3 21/76] fpga: Add a LATTICE option 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (19 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 20/76] samsung: Drop CONFIG_EXYNOS_PWM_BL Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 22/76] fpga: Add a FPGA_STRATIX_II option Simon Glass ` (51 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass There is no Kconfig option for this code, but it seems to be useful. Add one. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/fpga/Kconfig | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig index 4113de230cd..2034d0ebd9c 100644 --- a/drivers/fpga/Kconfig +++ b/drivers/fpga/Kconfig @@ -54,6 +54,12 @@ config FPGA_INTEL_SDM_MAILBOX Enable FPGA driver for writing full bitstream into Intel FPGA devices through SDM (Secure Device Manager) Mailbox. +config FPGA_LATTICE + bool "Enable Lattice FPGA driver" + help + This is used for the lattice FPGAs. Please check the source code as + there is no documentation for this at present. + config FPGA_XILINX bool "Enable Xilinx FPGA drivers" select FPGA -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 22/76] fpga: Add a FPGA_STRATIX_II option 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (20 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 21/76] fpga: Add a LATTICE option Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 23/76] misc: Drop mc9sdz60 driver Simon Glass ` (50 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass There is no Kconfig option for this code, but it seems to be useful. Add one. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/fpga/Kconfig | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig index 2034d0ebd9c..61490d6d8de 100644 --- a/drivers/fpga/Kconfig +++ b/drivers/fpga/Kconfig @@ -21,6 +21,12 @@ config FPGA_SOCFPGA This provides common functionality for Gen5 and Arria10 devices. +config FPGA_STRATIX_II + bool "Enable Stratix II FPGA drivers" + depends on FPGA_ALTERA + help + Say Y here to enable the Altera Stratix II FPGA-specific driver. + config FPGA_STRATIX_V bool "Enable Stratix V FPGA drivers" depends on FPGA_ALTERA -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 23/76] misc: Drop mc9sdz60 driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (21 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 22/76] fpga: Add a FPGA_STRATIX_II option Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 24/76] freescale: Drop unused pixis code Simon Glass ` (49 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass Drop this unused driver. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/misc/Makefile | 1 - drivers/misc/mc9sdz60.c | 34 ---------------------------------- 2 files changed, 35 deletions(-) delete mode 100644 drivers/misc/mc9sdz60.c diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile index 2de510329d8..3b792f2a14c 100644 --- a/drivers/misc/Makefile +++ b/drivers/misc/Makefile @@ -36,7 +36,6 @@ obj-$(CONFIG_DS4510) += ds4510.o obj-$(CONFIG_FSL_DEVICE_DISABLE) += fsl_devdis.o obj-$(CONFIG_FSL_IFC) += fsl_ifc.o obj-$(CONFIG_FSL_IIM) += fsl_iim.o -obj-$(CONFIG_FSL_MC9SDZ60) += mc9sdz60.o obj-$(CONFIG_FSL_SEC_MON) += fsl_sec_mon.o obj-$(CONFIG_$(SPL_)FS_LOADER) += fs_loader.o obj-$(CONFIG_GATEWORKS_SC) += gsc.o diff --git a/drivers/misc/mc9sdz60.c b/drivers/misc/mc9sdz60.c deleted file mode 100644 index e68a056a559..00000000000 --- a/drivers/misc/mc9sdz60.c +++ /dev/null @@ -1,34 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2010 Stefano Babic <sbabic@denx.de> - */ - - -#include <config.h> -#include <common.h> -#include <linux/errno.h> -#include <linux/types.h> -#include <i2c.h> -#include <mc9sdz60.h> - -#ifndef CONFIG_SYS_FSL_MC9SDZ60_I2C_ADDR -#error "You have to configure I2C address for MC9SDZ60" -#endif - - -u8 mc9sdz60_reg_read(enum mc9sdz60_reg reg) -{ - u8 val; - - if (i2c_read(CONFIG_SYS_FSL_MC9SDZ60_I2C_ADDR, reg, 1, &val, 1)) { - puts("Error reading MC9SDZ60 register\n"); - return -1; - } - - return val; -} - -void mc9sdz60_reg_write(enum mc9sdz60_reg reg, u8 val) -{ - i2c_write(CONFIG_SYS_FSL_MC9SDZ60_I2C_ADDR, reg, 1, &val, 1); -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 24/76] freescale: Drop unused pixis code 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (22 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 23/76] misc: Drop mc9sdz60 driver Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 25/76] freescale: Drop unused ftpmu010 driver Simon Glass ` (48 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass Drop this unused code. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) board/freescale/common/Makefile | 1 - board/freescale/common/pixis.c | 470 -------------------------------- board/freescale/common/pixis.h | 54 ---- 3 files changed, 525 deletions(-) delete mode 100644 board/freescale/common/pixis.c delete mode 100644 board/freescale/common/pixis.h diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index cc1371867d8..fc51d6d3e18 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -29,7 +29,6 @@ endif obj-$(CONFIG_FSL_CADMUS) += cadmus.o obj-$(CONFIG_FSL_VIA) += cds_via.o obj-$(CONFIG_FMAN_ENET) += fman.o -obj-$(CONFIG_FSL_PIXIS) += pixis.o ifndef CONFIG_SPL_BUILD obj-$(CONFIG_FSL_NGPIXIS) += ngpixis.o endif diff --git a/board/freescale/common/pixis.c b/board/freescale/common/pixis.c deleted file mode 100644 index 7096b107e54..00000000000 --- a/board/freescale/common/pixis.c +++ /dev/null @@ -1,470 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2006,2010 Freescale Semiconductor - * Jeff Brown - * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) - */ - -#include <common.h> -#include <command.h> -#include <asm/io.h> - -#define pixis_base (u8 *)PIXIS_BASE - -/* - * Simple board reset. - */ -void pixis_reset(void) -{ - out_8(pixis_base + PIXIS_RST, 0); - - while (1); -} - -/* - * Per table 27, page 58 of MPC8641HPCN spec. - */ -static int set_px_sysclk(unsigned long sysclk) -{ - u8 sysclk_s, sysclk_r, sysclk_v, vclkh, vclkl, sysclk_aux; - - switch (sysclk) { - case 33: - sysclk_s = 0x04; - sysclk_r = 0x04; - sysclk_v = 0x07; - sysclk_aux = 0x00; - break; - case 40: - sysclk_s = 0x01; - sysclk_r = 0x1F; - sysclk_v = 0x20; - sysclk_aux = 0x01; - break; - case 50: - sysclk_s = 0x01; - sysclk_r = 0x1F; - sysclk_v = 0x2A; - sysclk_aux = 0x02; - break; - case 66: - sysclk_s = 0x01; - sysclk_r = 0x04; - sysclk_v = 0x04; - sysclk_aux = 0x03; - break; - case 83: - sysclk_s = 0x01; - sysclk_r = 0x1F; - sysclk_v = 0x4B; - sysclk_aux = 0x04; - break; - case 100: - sysclk_s = 0x01; - sysclk_r = 0x1F; - sysclk_v = 0x5C; - sysclk_aux = 0x05; - break; - case 134: - sysclk_s = 0x06; - sysclk_r = 0x1F; - sysclk_v = 0x3B; - sysclk_aux = 0x06; - break; - case 166: - sysclk_s = 0x06; - sysclk_r = 0x1F; - sysclk_v = 0x4B; - sysclk_aux = 0x07; - break; - default: - printf("Unsupported SYSCLK frequency.\n"); - return 0; - } - - vclkh = (sysclk_s << 5) | sysclk_r; - vclkl = sysclk_v; - - out_8(pixis_base + PIXIS_VCLKH, vclkh); - out_8(pixis_base + PIXIS_VCLKL, vclkl); - - out_8(pixis_base + PIXIS_AUX, sysclk_aux); - - return 1; -} - -/* Set the CFG_SYSPLL bits - * - * This only has effect if PX_VCFGEN0[SYSPLL]=1, which is true if - * read_from_px_regs() is called. - */ -static int set_px_mpxpll(unsigned long mpxpll) -{ - switch (mpxpll) { - case 2: - case 4: - case 6: - case 8: - case 10: - case 12: - case 14: - case 16: - clrsetbits_8(pixis_base + PIXIS_VSPEED1, 0x1F, mpxpll); - return 1; - } - - printf("Unsupported MPXPLL ratio.\n"); - return 0; -} - -static int set_px_corepll(unsigned long corepll) -{ - u8 val; - - switch (corepll) { - case 20: - val = 0x08; - break; - case 25: - val = 0x0C; - break; - case 30: - val = 0x10; - break; - case 35: - val = 0x1C; - break; - case 40: - val = 0x14; - break; - case 45: - val = 0x0E; - break; - default: - printf("Unsupported COREPLL ratio.\n"); - return 0; - } - - clrsetbits_8(pixis_base + PIXIS_VSPEED0, 0x1F, val); - return 1; -} - -#ifndef CFG_SYS_PIXIS_VCFGEN0_ENABLE -#define CFG_SYS_PIXIS_VCFGEN0_ENABLE 0x1C -#endif - -/* Tell the PIXIS where to find the COREPLL, MPXPLL, SYSCLK values - * - * The PIXIS can be programmed to look at either the on-board dip switches - * or various other PIXIS registers to determine the values for COREPLL, - * MPXPLL, and SYSCLK. - * - * CFG_SYS_PIXIS_VCFGEN0_ENABLE is the value to write to the PIXIS_VCFGEN0 - * register that tells the pixis to use the various PIXIS register. - */ -static void read_from_px_regs(int set) -{ - u8 tmp = in_8(pixis_base + PIXIS_VCFGEN0); - - if (set) - tmp = tmp | CFG_SYS_PIXIS_VCFGEN0_ENABLE; - else - tmp = tmp & ~CFG_SYS_PIXIS_VCFGEN0_ENABLE; - - out_8(pixis_base + PIXIS_VCFGEN0, tmp); -} - -/* CFG_SYS_PIXIS_VBOOT_ENABLE is the value to write to the PX_VCFGEN1 - * register that tells the pixis to use the PX_VBOOT[LBMAP] register. - */ -#ifndef CFG_SYS_PIXIS_VBOOT_ENABLE -#define CFG_SYS_PIXIS_VBOOT_ENABLE 0x04 -#endif - -/* Configure the source of the boot location - * - * The PIXIS can be programmed to look at either the on-board dip switches - * or the PX_VBOOT[LBMAP] register to determine where we should boot. - * - * If we want to boot from the alternate boot bank, we need to tell the PIXIS - * to ignore the on-board dip switches and use the PX_VBOOT[LBMAP] instead. - */ -static void read_from_px_regs_altbank(int set) -{ - u8 tmp = in_8(pixis_base + PIXIS_VCFGEN1); - - if (set) - tmp = tmp | CFG_SYS_PIXIS_VBOOT_ENABLE; - else - tmp = tmp & ~CFG_SYS_PIXIS_VBOOT_ENABLE; - - out_8(pixis_base + PIXIS_VCFGEN1, tmp); -} - -/* CFG_SYS_PIXIS_VBOOT_MASK contains the bits to set in VBOOT register that - * tells the PIXIS what the alternate flash bank is. - * - * Note that it's not really a mask. It contains the actual LBMAP bits that - * must be set to select the alternate bank. This code assumes that the - * primary bank has these bits set to 0, and the alternate bank has these - * bits set to 1. - */ -#ifndef CFG_SYS_PIXIS_VBOOT_MASK -#define CFG_SYS_PIXIS_VBOOT_MASK (0x40) -#endif - -/* Tell the PIXIS to boot from the default flash bank - * - * Program the default flash bank into the VBOOT register. This register is - * used only if PX_VCFGEN1[FLASH]=1. - */ -static void clear_altbank(void) -{ - clrbits_8(pixis_base + PIXIS_VBOOT, CFG_SYS_PIXIS_VBOOT_MASK); -} - -/* Tell the PIXIS to boot from the alternate flash bank - * - * Program the alternate flash bank into the VBOOT register. This register is - * used only if PX_VCFGEN1[FLASH]=1. - */ -static void set_altbank(void) -{ - setbits_8(pixis_base + PIXIS_VBOOT, CFG_SYS_PIXIS_VBOOT_MASK); -} - -/* Reset the board with watchdog disabled. - * - * This respects the altbank setting. - */ -static void set_px_go(void) -{ - /* Disable the VELA sequencer and watchdog */ - clrbits_8(pixis_base + PIXIS_VCTL, 9); - - /* Reboot by starting the VELA sequencer */ - setbits_8(pixis_base + PIXIS_VCTL, 0x1); - - while (1); -} - -/* Reset the board with watchdog enabled. - * - * This respects the altbank setting. - */ -static void set_px_go_with_watchdog(void) -{ - /* Disable the VELA sequencer */ - clrbits_8(pixis_base + PIXIS_VCTL, 1); - - /* Enable the watchdog and reboot by starting the VELA sequencer */ - setbits_8(pixis_base + PIXIS_VCTL, 0x9); - - while (1); -} - -/* Disable the watchdog - * - */ -static int pixis_disable_watchdog_cmd(struct cmd_tbl *cmdtp, int flag, int argc, - char *const argv[]) -{ - /* Disable the VELA sequencer and the watchdog */ - clrbits_8(pixis_base + PIXIS_VCTL, 9); - - return 0; -} - -U_BOOT_CMD( - diswd, 1, 0, pixis_disable_watchdog_cmd, - "Disable watchdog timer", - "" -); - -/* - * This function takes the non-integral cpu:mpx pll ratio - * and converts it to an integer that can be used to assign - * FPGA register values. - * input: strptr i.e. argv[2] - */ -static unsigned long strfractoint(char *strptr) -{ - int i, j; - int mulconst; - int no_dec = 0; - unsigned long intval = 0, decval = 0; - char intarr[3], decarr[3]; - - /* Assign the integer part to intarr[] - * If there is no decimal point i.e. - * if the ratio is an integral value - * simply create the intarr. - */ - i = 0; - while (strptr[i] != '.') { - if (strptr[i] == 0) { - no_dec = 1; - break; - } - intarr[i] = strptr[i]; - i++; - } - - intarr[i] = '\0'; - - if (no_dec) { - /* Currently needed only for single digit corepll ratios */ - mulconst = 10; - decval = 0; - } else { - j = 0; - i++; /* Skipping the decimal point */ - while ((strptr[i] >= '0') && (strptr[i] <= '9')) { - decarr[j] = strptr[i]; - i++; - j++; - } - - decarr[j] = '\0'; - - mulconst = 1; - for (i = 0; i < j; i++) - mulconst *= 10; - decval = dectoul(decarr, NULL); - } - - intval = dectoul(intarr, NULL); - intval = intval * mulconst; - - return intval + decval; -} - -static int pixis_reset_cmd(struct cmd_tbl *cmdtp, int flag, int argc, - char *const argv[]) -{ - unsigned int i; - char *p_cf = NULL; - char *p_cf_sysclk = NULL; - char *p_cf_corepll = NULL; - char *p_cf_mpxpll = NULL; - char *p_altbank = NULL; - char *p_wd = NULL; - int unknown_param = 0; - - /* - * No args is a simple reset request. - */ - if (argc <= 1) { - pixis_reset(); - /* not reached */ - } - - for (i = 1; i < argc; i++) { - if (strcmp(argv[i], "cf") == 0) { - p_cf = argv[i]; - if (i + 3 >= argc) { - break; - } - p_cf_sysclk = argv[i+1]; - p_cf_corepll = argv[i+2]; - p_cf_mpxpll = argv[i+3]; - i += 3; - continue; - } - - if (strcmp(argv[i], "altbank") == 0) { - p_altbank = argv[i]; - continue; - } - - if (strcmp(argv[i], "wd") == 0) { - p_wd = argv[i]; - continue; - } - - unknown_param = 1; - } - - /* - * Check that cf has all required parms - */ - if ((p_cf && !(p_cf_sysclk && p_cf_corepll && p_cf_mpxpll)) - || unknown_param) { -#ifdef CONFIG_SYS_LONGHELP - puts(cmdtp->help); - putc('\n'); -#endif - return 1; - } - - /* - * PIXIS seems to be sensitive to the ordering of - * the registers that are touched. - */ - read_from_px_regs(0); - - if (p_altbank) - read_from_px_regs_altbank(0); - - clear_altbank(); - - /* - * Clock configuration specified. - */ - if (p_cf) { - unsigned long sysclk; - unsigned long corepll; - unsigned long mpxpll; - - sysclk = dectoul(p_cf_sysclk, NULL); - corepll = strfractoint(p_cf_corepll); - mpxpll = dectoul(p_cf_mpxpll, NULL); - - if (!(set_px_sysclk(sysclk) - && set_px_corepll(corepll) - && set_px_mpxpll(mpxpll))) { -#ifdef CONFIG_SYS_LONGHELP - puts(cmdtp->help); - putc('\n'); -#endif - return 1; - } - read_from_px_regs(1); - } - - /* - * Altbank specified - * - * NOTE CHANGE IN BEHAVIOR: previous code would default - * to enabling watchdog if altbank is specified. - * Now the watchdog must be enabled explicitly using 'wd'. - */ - if (p_altbank) { - set_altbank(); - read_from_px_regs_altbank(1); - } - - /* - * Reset with watchdog specified. - */ - if (p_wd) - set_px_go_with_watchdog(); - else - set_px_go(); - - /* - * Shouldn't be reached. - */ - return 0; -} - - -U_BOOT_CMD( - pixis_reset, CONFIG_SYS_MAXARGS, 1, pixis_reset_cmd, - "Reset the board using the FPGA sequencer", - " pixis_reset\n" - " pixis_reset [altbank]\n" - " pixis_reset altbank wd\n" - " pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>\n" - " pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>" -); diff --git a/board/freescale/common/pixis.h b/board/freescale/common/pixis.h deleted file mode 100644 index f19e85cb1c9..00000000000 --- a/board/freescale/common/pixis.h +++ /dev/null @@ -1,54 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2010 Freescale Semiconductor, Inc. - */ -#ifndef __PIXIS_H_ -#define __PIXIS_H_ 1 - -/* PIXIS register set. */ -#if defined(CONFIG_TARGET_MPC8536DS) -typedef struct pixis { - u8 id; - u8 ver; - u8 pver; - u8 csr; - u8 rst; - u8 rst2; - u8 aux1; - u8 spd; - u8 aux2; - u8 csr2; - u8 watch; - u8 led; - u8 pwr; - u8 res[3]; - u8 vctl; - u8 vstat; - u8 vcfgen0; - u8 vcfgen1; - u8 vcore0; - u8 res1; - u8 vboot; - u8 vspeed[3]; - u8 sclk[3]; - u8 dclk[3]; - u8 i2cdacr; - u8 vcoreacc[4]; - u8 vcorecnt[3]; - u8 vcoremax[2]; - u8 vplatacc[4]; - u8 vplatcnt[3]; - u8 vplatmax[2]; - u8 vtempacc[4]; - u8 vtempcnt[3]; - u8 vtempmax[2]; - u8 res2[4]; -} __attribute__ ((packed)) pixis_t; -#else -#error Need to define pixis_t for this board -#endif - -/* Pointer to the PIXIS register set */ -#define pixis ((pixis_t *)PIXIS_BASE) - -#endif /* __PIXIS_H_ */ -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 25/76] freescale: Drop unused ftpmu010 driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (23 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 24/76] freescale: Drop unused pixis code Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 26/76] rcar: Drop timer Simon Glass ` (47 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass Drop this unused code. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/power/Makefile | 1 - drivers/power/ftpmu010.c | 87 -------------- include/faraday/ftpmu010.h | 234 ------------------------------------- 3 files changed, 322 deletions(-) delete mode 100644 drivers/power/ftpmu010.c delete mode 100644 include/faraday/ftpmu010.h diff --git a/drivers/power/Makefile b/drivers/power/Makefile index f805027784d..34a84808a9c 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -18,7 +18,6 @@ obj-$(CONFIG_AXP305_POWER) += axp305.o obj-$(CONFIG_AXP809_POWER) += axp809.o obj-$(CONFIG_AXP818_POWER) += axp818.o obj-$(CONFIG_EXYNOS_TMU) += exynos-tmu.o -obj-$(CONFIG_FTPMU010_POWER) += ftpmu010.o obj-$(CONFIG_SY8106A_POWER) += sy8106a.o obj-$(CONFIG_TPS6586X_POWER) += tps6586x.o obj-$(CONFIG_TWL4030_POWER) += twl4030.o diff --git a/drivers/power/ftpmu010.c b/drivers/power/ftpmu010.c deleted file mode 100644 index 9a48b36554d..00000000000 --- a/drivers/power/ftpmu010.c +++ /dev/null @@ -1,87 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2009 Faraday Technology - * Po-Yu Chuang <ratbert@faraday-tech.com> - * - * Copyright (C) 2010 Andes Technology Corporation - * Shawn Lin, Andes Technology Corporation <nobuhiro@andestech.com> - * Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com> - */ - -#include <common.h> -#include <asm/io.h> -#include <faraday/ftpmu010.h> - -/* OSCC: OSC Control Register */ -void ftpmu010_32768osc_enable(void) -{ - static struct ftpmu010 *pmu = (struct ftpmu010 *)CONFIG_FTPMU010_BASE; - unsigned int oscc; - - /* enable the 32768Hz oscillator */ - oscc = readl(&pmu->OSCC); - oscc &= ~(FTPMU010_OSCC_OSCL_OFF | FTPMU010_OSCC_OSCL_TRI); - writel(oscc, &pmu->OSCC); - - /* wait until ready */ - while (!(readl(&pmu->OSCC) & FTPMU010_OSCC_OSCL_STABLE)) - ; - - /* select 32768Hz oscillator */ - oscc = readl(&pmu->OSCC); - oscc |= FTPMU010_OSCC_OSCL_RTCLSEL; - writel(oscc, &pmu->OSCC); -} - -/* MFPSR: Multi-Function Port Setting Register */ -void ftpmu010_mfpsr_select_dev(unsigned int dev) -{ - static struct ftpmu010 *pmu = (struct ftpmu010 *)CONFIG_FTPMU010_BASE; - unsigned int mfpsr; - - mfpsr = readl(&pmu->MFPSR); - mfpsr |= dev; - writel(mfpsr, &pmu->MFPSR); -} - -void ftpmu010_mfpsr_diselect_dev(unsigned int dev) -{ - static struct ftpmu010 *pmu = (struct ftpmu010 *)CONFIG_FTPMU010_BASE; - unsigned int mfpsr; - - mfpsr = readl(&pmu->MFPSR); - mfpsr &= ~dev; - writel(mfpsr, &pmu->MFPSR); -} - -/* PDLLCR0: PLL/DLL Control Register 0 */ -void ftpmu010_dlldis_disable(void) -{ - static struct ftpmu010 *pmu = (struct ftpmu010 *)CONFIG_FTPMU010_BASE; - unsigned int pdllcr0; - - pdllcr0 = readl(&pmu->PDLLCR0); - pdllcr0 |= FTPMU010_PDLLCR0_DLLDIS; - writel(pdllcr0, &pmu->PDLLCR0); -} - -void ftpmu010_sdram_clk_disable(unsigned int cr0) -{ - static struct ftpmu010 *pmu = (struct ftpmu010 *)CONFIG_FTPMU010_BASE; - unsigned int pdllcr0; - - pdllcr0 = readl(&pmu->PDLLCR0); - pdllcr0 |= FTPMU010_PDLLCR0_HCLKOUTDIS(cr0); - writel(pdllcr0, &pmu->PDLLCR0); -} - -/* SDRAMHTC: SDRAM Signal Hold Time Control */ -void ftpmu010_sdramhtc_set(unsigned int val) -{ - static struct ftpmu010 *pmu = (struct ftpmu010 *)CONFIG_FTPMU010_BASE; - unsigned int sdramhtc; - - sdramhtc = readl(&pmu->SDRAMHTC); - sdramhtc |= val; - writel(sdramhtc, &pmu->SDRAMHTC); -} diff --git a/include/faraday/ftpmu010.h b/include/faraday/ftpmu010.h deleted file mode 100644 index ccb7805375e..00000000000 --- a/include/faraday/ftpmu010.h +++ /dev/null @@ -1,234 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2009 Faraday Technology - * Po-Yu Chuang <ratbert@faraday-tech.com> - */ - -/* - * Power Management Unit - */ -#ifndef __FTPMU010_H -#define __FTPMU010_H - -#ifndef __ASSEMBLY__ -struct ftpmu010 { - unsigned int IDNMBR0; /* 0x00 */ - unsigned int reserved0; /* 0x04 */ - unsigned int OSCC; /* 0x08 */ - unsigned int PMODE; /* 0x0C */ - unsigned int PMCR; /* 0x10 */ - unsigned int PED; /* 0x14 */ - unsigned int PEDSR; /* 0x18 */ - unsigned int reserved1; /* 0x1C */ - unsigned int PMSR; /* 0x20 */ - unsigned int PGSR; /* 0x24 */ - unsigned int MFPSR; /* 0x28 */ - unsigned int MISC; /* 0x2C */ - unsigned int PDLLCR0; /* 0x30 */ - unsigned int PDLLCR1; /* 0x34 */ - unsigned int AHBMCLKOFF; /* 0x38 */ - unsigned int APBMCLKOFF; /* 0x3C */ - unsigned int DCSRCR0; /* 0x40 */ - unsigned int DCSRCR1; /* 0x44 */ - unsigned int DCSRCR2; /* 0x48 */ - unsigned int SDRAMHTC; /* 0x4C */ - unsigned int PSPR0; /* 0x50 */ - unsigned int PSPR1; /* 0x54 */ - unsigned int PSPR2; /* 0x58 */ - unsigned int PSPR3; /* 0x5C */ - unsigned int PSPR4; /* 0x60 */ - unsigned int PSPR5; /* 0x64 */ - unsigned int PSPR6; /* 0x68 */ - unsigned int PSPR7; /* 0x6C */ - unsigned int PSPR8; /* 0x70 */ - unsigned int PSPR9; /* 0x74 */ - unsigned int PSPR10; /* 0x78 */ - unsigned int PSPR11; /* 0x7C */ - unsigned int PSPR12; /* 0x80 */ - unsigned int PSPR13; /* 0x84 */ - unsigned int PSPR14; /* 0x88 */ - unsigned int PSPR15; /* 0x8C */ - unsigned int AHBDMA_RACCS; /* 0x90 */ - unsigned int reserved2; /* 0x94 */ - unsigned int reserved3; /* 0x98 */ - unsigned int JSS; /* 0x9C */ - unsigned int CFC_RACC; /* 0xA0 */ - unsigned int SSP1_RACC; /* 0xA4 */ - unsigned int UART1TX_RACC; /* 0xA8 */ - unsigned int UART1RX_RACC; /* 0xAC */ - unsigned int UART2TX_RACC; /* 0xB0 */ - unsigned int UART2RX_RACC; /* 0xB4 */ - unsigned int SDC_RACC; /* 0xB8 */ - unsigned int I2SAC97_RACC; /* 0xBC */ - unsigned int IRDATX_RACC; /* 0xC0 */ - unsigned int reserved4; /* 0xC4 */ - unsigned int USBD_RACC; /* 0xC8 */ - unsigned int IRDARX_RACC; /* 0xCC */ - unsigned int IRDA_RACC; /* 0xD0 */ - unsigned int ED0_RACC; /* 0xD4 */ - unsigned int ED1_RACC; /* 0xD8 */ -}; -#endif /* __ASSEMBLY__ */ - -/* - * ID Number 0 Register - */ -#define FTPMU010_ID_A320A 0x03200000 -#define FTPMU010_ID_A320C 0x03200010 -#define FTPMU010_ID_A320D 0x03200030 - -/* - * OSC Control Register - */ -#define FTPMU010_OSCC_OSCH_TRI (1 << 11) -#define FTPMU010_OSCC_OSCH_STABLE (1 << 9) -#define FTPMU010_OSCC_OSCH_OFF (1 << 8) - -#define FTPMU010_OSCC_OSCL_TRI (1 << 3) -#define FTPMU010_OSCC_OSCL_RTCLSEL (1 << 2) -#define FTPMU010_OSCC_OSCL_STABLE (1 << 1) -#define FTPMU010_OSCC_OSCL_OFF (1 << 0) - -/* - * Power Mode Register - */ -#define FTPMU010_PMODE_DIVAHBCLK_MASK (0x7 << 4) -#define FTPMU010_PMODE_DIVAHBCLK_2 (0x0 << 4) -#define FTPMU010_PMODE_DIVAHBCLK_3 (0x1 << 4) -#define FTPMU010_PMODE_DIVAHBCLK_4 (0x2 << 4) -#define FTPMU010_PMODE_DIVAHBCLK_6 (0x3 << 4) -#define FTPMU010_PMODE_DIVAHBCLK_8 (0x4 << 4) -#define FTPMU010_PMODE_DIVAHBCLK(pmode) (((pmode) >> 4) & 0x7) -#define FTPMU010_PMODE_FCS (1 << 2) -#define FTPMU010_PMODE_TURBO (1 << 1) -#define FTPMU010_PMODE_SLEEP (1 << 0) - -/* - * Power Manager Status Register - */ -#define FTPMU010_PMSR_SMR (1 << 10) - -#define FTPMU010_PMSR_RDH (1 << 2) -#define FTPMU010_PMSR_PH (1 << 1) -#define FTPMU010_PMSR_CKEHLOW (1 << 0) - -/* - * Multi-Function Port Setting Register - */ -#define FTPMU010_MFPSR_DEBUGSEL (1 << 17) -#define FTPMU010_MFPSR_DMA0PINSEL (1 << 16) -#define FTPMU010_MFPSR_DMA1PINSEL (1 << 15) -#define FTPMU010_MFPSR_MODEMPINSEL (1 << 14) -#define FTPMU010_MFPSR_AC97CLKOUTSEL (1 << 13) -#define FTPMU010_MFPSR_PWM1PINSEL (1 << 11) -#define FTPMU010_MFPSR_PWM0PINSEL (1 << 10) -#define FTPMU010_MFPSR_IRDACLKSEL (1 << 9) -#define FTPMU010_MFPSR_UARTCLKSEL (1 << 8) -#define FTPMU010_MFPSR_SSPCLKSEL (1 << 6) -#define FTPMU010_MFPSR_I2SCLKSEL (1 << 5) -#define FTPMU010_MFPSR_AC97CLKSEL (1 << 4) -#define FTPMU010_MFPSR_AC97PINSEL (1 << 3) -#define FTPMU010_MFPSR_TRIAHBDIS (1 << 1) -#define FTPMU010_MFPSR_TRIAHBDBG (1 << 0) - -/* - * PLL/DLL Control Register 0 - * Note: - * 1. FTPMU010_PDLLCR0_HCLKOUTDIS: - * Datasheet indicated it starts at bit #21 which was wrong. - * 2. FTPMU010_PDLLCR0_DLLFRAG: - * Datasheet indicated it has 2 bit which was wrong. - */ -#define FTPMU010_PDLLCR0_HCLKOUTDIS(cr0) (((cr0) & 0xf) << 20) -#define FTPMU010_PDLLCR0_DLLFRAG(cr0) (1 << 19) -#define FTPMU010_PDLLCR0_DLLSTSEL (1 << 18) -#define FTPMU010_PDLLCR0_DLLSTABLE (1 << 17) -#define FTPMU010_PDLLCR0_DLLDIS (1 << 16) -#define FTPMU010_PDLLCR0_PLL1FRANG(cr0) (((cr0) & 0x3) << 12) -#define FTPMU010_PDLLCR0_PLL1NS(cr0) (((cr0) & 0x1ff) << 3) -#define FTPMU010_PDLLCR0_PLL1STSEL (1 << 2) -#define FTPMU010_PDLLCR0_PLL1STABLE (1 << 1) -#define FTPMU010_PDLLCR0_PLL1DIS (1 << 0) - -/* - * SDRAM Signal Hold Time Control Register - */ -#define FTPMU010_SDRAMHTC_RCLK_DLY(x) (((x) & 0xf) << 28) -#define FTPMU010_SDRAMHTC_CTL_WCLK_DLY(x) (((x) & 0xf) << 24) -#define FTPMU010_SDRAMHTC_DAT_WCLK_DLY(x) (((x) & 0xf) << 20) -#define FTPMU010_SDRAMHTC_EBICTRL_DCSR (1 << 18) -#define FTPMU010_SDRAMHTC_EBIDATA_DCSR (1 << 17) -#define FTPMU010_SDRAMHTC_SDRAMCS_DCSR (1 << 16) -#define FTPMU010_SDRAMHTC_SDRAMCTL_DCSR (1 << 15) -#define FTPMU010_SDRAMHTC_CKE_DCSR (1 << 14) -#define FTPMU010_SDRAMHTC_DQM_DCSR (1 << 13) -#define FTPMU010_SDRAMHTC_SDCLK_DCSR (1 << 12) - -#ifndef __ASSEMBLY__ -void ftpmu010_32768osc_enable(void); -void ftpmu010_dlldis_disable(void); -void ftpmu010_mfpsr_diselect_dev(unsigned int dev); -void ftpmu010_mfpsr_select_dev(unsigned int dev); -void ftpmu010_sdram_clk_disable(unsigned int cr0); -void ftpmu010_sdramhtc_set(unsigned int val); -#endif - -#ifdef __ASSEMBLY__ -#define FTPMU010_IDNMBR0 0x00 -#define FTPMU010_reserved0 0x04 -#define FTPMU010_OSCC 0x08 -#define FTPMU010_PMODE 0x0C -#define FTPMU010_PMCR 0x10 -#define FTPMU010_PED 0x14 -#define FTPMU010_PEDSR 0x18 -#define FTPMU010_reserved1 0x1C -#define FTPMU010_PMSR 0x20 -#define FTPMU010_PGSR 0x24 -#define FTPMU010_MFPSR 0x28 -#define FTPMU010_MISC 0x2C -#define FTPMU010_PDLLCR0 0x30 -#define FTPMU010_PDLLCR1 0x34 -#define FTPMU010_AHBMCLKOFF 0x38 -#define FTPMU010_APBMCLKOFF 0x3C -#define FTPMU010_DCSRCR0 0x40 -#define FTPMU010_DCSRCR1 0x44 -#define FTPMU010_DCSRCR2 0x48 -#define FTPMU010_SDRAMHTC 0x4C -#define FTPMU010_PSPR0 0x50 -#define FTPMU010_PSPR1 0x54 -#define FTPMU010_PSPR2 0x58 -#define FTPMU010_PSPR3 0x5C -#define FTPMU010_PSPR4 0x60 -#define FTPMU010_PSPR5 0x64 -#define FTPMU010_PSPR6 0x68 -#define FTPMU010_PSPR7 0x6C -#define FTPMU010_PSPR8 0x70 -#define FTPMU010_PSPR9 0x74 -#define FTPMU010_PSPR10 0x78 -#define FTPMU010_PSPR11 0x7C -#define FTPMU010_PSPR12 0x80 -#define FTPMU010_PSPR13 0x84 -#define FTPMU010_PSPR14 0x88 -#define FTPMU010_PSPR15 0x8C -#define FTPMU010_AHBDMA_RACCS 0x90 -#define FTPMU010_reserved2 0x94 -#define FTPMU010_reserved3 0x98 -#define FTPMU010_JSS 0x9C -#define FTPMU010_CFC_RACC 0xA0 -#define FTPMU010_SSP1_RACC 0xA4 -#define FTPMU010_UART1TX_RACC 0xA8 -#define FTPMU010_UART1RX_RACC 0xAC -#define FTPMU010_UART2TX_RACC 0xB0 -#define FTPMU010_UART2RX_RACC 0xB4 -#define FTPMU010_SDC_RACC 0xB8 -#define FTPMU010_I2SAC97_RACC 0xBC -#define FTPMU010_IRDATX_RACC 0xC0 -#define FTPMU010_reserved4 0xC4 -#define FTPMU010_USBD_RACC 0xC8 -#define FTPMU010_IRDARX_RACC 0xCC -#define FTPMU010_IRDA_RACC 0xD0 -#define FTPMU010_ED0_RACC 0xD4 -#define FTPMU010_ED1_RACC 0xD8 -#endif /* __ASSEMBLY__ */ - -#endif /* __FTPMU010_H */ -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 26/76] rcar: Drop timer 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (24 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 25/76] freescale: Drop unused ftpmu010 driver Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 27/76] imx: Drop unused CONFIG_IMX Simon Glass ` (46 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass Drop this unused driver. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/arm/mach-rmobile/Makefile | 1 - arch/arm/mach-rmobile/timer.c | 87 ---------------------------------- 2 files changed, 88 deletions(-) delete mode 100644 arch/arm/mach-rmobile/timer.c diff --git a/arch/arm/mach-rmobile/Makefile b/arch/arm/mach-rmobile/Makefile index 195bbeb5c88..3f77760e50d 100644 --- a/arch/arm/mach-rmobile/Makefile +++ b/arch/arm/mach-rmobile/Makefile @@ -7,7 +7,6 @@ obj-y = cpu_info.o obj-y += emac.o obj-$(CONFIG_DISPLAY_BOARDINFO) += board.o -obj-$(CONFIG_GLOBAL_TIMER) += timer.o obj-$(CONFIG_TMU_TIMER) += ../../sh/lib/time.o obj-$(CONFIG_SH73A0) += lowlevel_init.o cpu_info-sh73a0.o pfc-sh73a0.o obj-$(CONFIG_R8A7740) += lowlevel_init.o cpu_info-r8a7740.o pfc-r8a7740.o diff --git a/arch/arm/mach-rmobile/timer.c b/arch/arm/mach-rmobile/timer.c deleted file mode 100644 index 293c23b5e25..00000000000 --- a/arch/arm/mach-rmobile/timer.c +++ /dev/null @@ -1,87 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2012 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> - * (C) Copyright 2012 Renesas Solutions Corp. - */ - -#include <common.h> -#include <div64.h> -#include <init.h> -#include <time.h> -#include <asm/io.h> -#include <asm/arch-armv7/globaltimer.h> -#include <asm/arch/rmobile.h> -#include <linux/delay.h> - -static struct globaltimer *global_timer = \ - (struct globaltimer *)GLOBAL_TIMER_BASE_ADDR; - -#define CLK2MHZ(clk) (clk / 1000 / 1000) -static u64 get_cpu_global_timer(void) -{ - u32 low, high; - u64 timer; - - u32 old = readl(&global_timer->cnt_h); - while (1) { - low = readl(&global_timer->cnt_l); - high = readl(&global_timer->cnt_h); - if (old == high) - break; - else - old = high; - } - - timer = high; - return (u64)((timer << 32) | low); -} - -static u64 get_time_us(void) -{ - u64 timer = get_cpu_global_timer(); - - timer = ((timer << 2) + (CLK2MHZ(CFG_SYS_CPU_CLK) >> 1)); - do_div(timer, CLK2MHZ(CFG_SYS_CPU_CLK)); - return timer; -} - -static ulong get_time_ms(void) -{ - u64 us = get_time_us(); - - do_div(us, 1000); - return us; -} - -int timer_init(void) -{ - writel(0x01, &global_timer->ctl); - return 0; -} - -void __udelay(unsigned long usec) -{ - u64 start, current; - u64 wait; - - start = get_cpu_global_timer(); - wait = (u64)((usec * CLK2MHZ(CFG_SYS_CPU_CLK)) >> 2); - do { - current = get_cpu_global_timer(); - } while ((current - start) < wait); -} - -ulong get_timer(ulong base) -{ - return get_time_ms() - base; -} - -unsigned long long get_ticks(void) -{ - return get_cpu_global_timer(); -} - -ulong get_tbclk(void) -{ - return (ulong)(CFG_SYS_CPU_CLK >> 2); -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 27/76] imx: Drop unused CONFIG_IMX 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (25 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 26/76] rcar: Drop timer Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 28/76] arm: Drop old kona code Simon Glass ` (45 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Stefano Babic This option does not exist, so the Makefile rule does nothing. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/arm/cpu/arm920t/Makefile | 2 -- 1 file changed, 2 deletions(-) diff --git a/arch/arm/cpu/arm920t/Makefile b/arch/arm/cpu/arm920t/Makefile index b70822c67ab..5ac3740621c 100644 --- a/arch/arm/cpu/arm920t/Makefile +++ b/arch/arm/cpu/arm920t/Makefile @@ -7,8 +7,6 @@ extra-y = start.o obj-y += cpu.o -obj-$(CONFIG_IMX) += imx/ - # some files can only build in ARM mode ifdef CONFIG_$(SPL_)SYS_THUMB_BUILD -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 28/76] arm: Drop old kona code 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (26 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 27/76] imx: Drop unused CONFIG_IMX Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 29/76] video: Drop unused lg4573 driver Simon Glass ` (44 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass The KONA and KONA_GPIO options don't exist anymore, since this commit: 0f6807e77b0 arm: Remove bcm28155_ap board Drop the dead code. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/arm/cpu/armv7/Makefile | 1 - arch/arm/cpu/armv7/kona-common/Makefile | 8 - arch/arm/cpu/armv7/kona-common/clk-stubs.c | 25 ---- .../arm/cpu/armv7/kona-common/hwinit-common.c | 17 --- arch/arm/cpu/armv7/kona-common/reset.S | 25 ---- arch/arm/cpu/armv7/kona-common/s_init.c | 11 -- drivers/gpio/Makefile | 1 - drivers/gpio/kona_gpio.c | 141 ------------------ 8 files changed, 229 deletions(-) delete mode 100644 arch/arm/cpu/armv7/kona-common/Makefile delete mode 100644 arch/arm/cpu/armv7/kona-common/clk-stubs.c delete mode 100644 arch/arm/cpu/armv7/kona-common/hwinit-common.c delete mode 100644 arch/arm/cpu/armv7/kona-common/reset.S delete mode 100644 arch/arm/cpu/armv7/kona-common/s_init.c delete mode 100644 drivers/gpio/kona_gpio.c diff --git a/arch/arm/cpu/armv7/Makefile b/arch/arm/cpu/armv7/Makefile index bfbd85ae64e..7d7907601ec 100644 --- a/arch/arm/cpu/armv7/Makefile +++ b/arch/arm/cpu/armv7/Makefile @@ -26,7 +26,6 @@ obj-$(CONFIG_ARMV7_NONSEC) += nonsec_virt.o virt-v7.o virt-dt.o obj-$(CONFIG_ARMV7_PSCI) += psci.o psci-common.o obj-$(CONFIG_IPROC) += iproc-common/ -obj-$(CONFIG_KONA) += kona-common/ obj-$(CONFIG_SYS_ARCH_TIMER) += arch_timer.o ifneq (,$(filter s5pc1xx exynos,$(SOC))) diff --git a/arch/arm/cpu/armv7/kona-common/Makefile b/arch/arm/cpu/armv7/kona-common/Makefile deleted file mode 100644 index 56de3d18e0e..00000000000 --- a/arch/arm/cpu/armv7/kona-common/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# Copyright 2013 Broadcom Corporation. - -obj-y += s_init.o -obj-y += hwinit-common.o -obj-y += clk-stubs.o -obj-${CONFIG_KONA_RESET_S} += reset.o diff --git a/arch/arm/cpu/armv7/kona-common/clk-stubs.c b/arch/arm/cpu/armv7/kona-common/clk-stubs.c deleted file mode 100644 index 4eddaca8879..00000000000 --- a/arch/arm/cpu/armv7/kona-common/clk-stubs.c +++ /dev/null @@ -1,25 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2013 Broadcom Corporation. - */ - -#include <common.h> - -/* - * These weak functions are available to kona architectures that don't - * require clock enables from the driver code. - */ -int __weak clk_sdio_enable(void *base, u32 rate, u32 *actual_ratep) -{ - return 0; -} - -int __weak clk_bsc_enable(void *base) -{ - return 0; -} - -int __weak clk_usb_otg_enable(void *base) -{ - return 0; -} diff --git a/arch/arm/cpu/armv7/kona-common/hwinit-common.c b/arch/arm/cpu/armv7/kona-common/hwinit-common.c deleted file mode 100644 index cfc7c9fbc64..00000000000 --- a/arch/arm/cpu/armv7/kona-common/hwinit-common.c +++ /dev/null @@ -1,17 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2013 Broadcom Corporation. - */ - -#include <common.h> -#include <cpu_func.h> -#include <asm/cache.h> -#include <linux/sizes.h> - -#if !CONFIG_IS_ENABLED(SYS_DCACHE_OFF) -void enable_caches(void) -{ - /* Enable D-cache. I-cache is already enabled in start.S */ - dcache_enable(); -} -#endif diff --git a/arch/arm/cpu/armv7/kona-common/reset.S b/arch/arm/cpu/armv7/kona-common/reset.S deleted file mode 100644 index eea835b341c..00000000000 --- a/arch/arm/cpu/armv7/kona-common/reset.S +++ /dev/null @@ -1,25 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2013 Broadcom Corporation. - */ - -.globl reset_cpu -reset_cpu: - ldr r1, =0x35001f00 - ldr r2, [r1] - ldr r4, =0x80000000 - and r4, r2, r4 - ldr r3, =0xA5A500 - orr r4, r4, r3 - orr r4, r4, #0x1 - - str r4, [r1] - - ldr r1, =0x35001f04 - ldr r2, [r1] - ldr r4, =0x80000000 - and r4, r2, r4 - str r4, [r1] - -_loop_forever: - b _loop_forever diff --git a/arch/arm/cpu/armv7/kona-common/s_init.c b/arch/arm/cpu/armv7/kona-common/s_init.c deleted file mode 100644 index 778b9176fa2..00000000000 --- a/arch/arm/cpu/armv7/kona-common/s_init.c +++ /dev/null @@ -1,11 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2014 Broadcom Corporation. - */ - -/* - * Early system init. Currently empty. - */ -void s_init(void) -{ -} diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 07fca7bd33d..ec65f70c318 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -23,7 +23,6 @@ obj-$(CONFIG_INTEL_ICH6_GPIO) += intel_ich6_gpio.o obj-$(CONFIG_INTEL_BROADWELL_GPIO) += intel_broadwell_gpio.o obj-$(CONFIG_IPROC_GPIO) += iproc_gpio.o obj-$(CONFIG_KIRKWOOD_GPIO) += kw_gpio.o -obj-$(CONFIG_KONA_GPIO) += kona_gpio.o obj-$(CONFIG_MCP230XX_GPIO) += mcp230xx_gpio.o obj-$(CONFIG_MXC_GPIO) += mxc_gpio.o obj-$(CONFIG_MXS_GPIO) += mxs_gpio.o diff --git a/drivers/gpio/kona_gpio.c b/drivers/gpio/kona_gpio.c deleted file mode 100644 index 29791882a34..00000000000 --- a/drivers/gpio/kona_gpio.c +++ /dev/null @@ -1,141 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2013 Broadcom Corporation. - */ - -#include <common.h> -#include <malloc.h> -#include <asm/io.h> -#include <asm/arch/sysmap.h> - -#define GPIO_BASE (void *)GPIO2_BASE_ADDR - -#define GPIO_PASSWD 0x00a5a501 -#define GPIO_PER_BANK 32 -#define GPIO_MAX_BANK_NUM 8 - -#define GPIO_BANK(gpio) ((gpio) >> 5) -#define GPIO_BITMASK(gpio) \ - (1UL << ((gpio) & (GPIO_PER_BANK - 1))) - -#define GPIO_OUT_STATUS(bank) (0x00000000 + ((bank) << 2)) -#define GPIO_IN_STATUS(bank) (0x00000020 + ((bank) << 2)) -#define GPIO_OUT_SET(bank) (0x00000040 + ((bank) << 2)) -#define GPIO_OUT_CLEAR(bank) (0x00000060 + ((bank) << 2)) -#define GPIO_INT_STATUS(bank) (0x00000080 + ((bank) << 2)) -#define GPIO_INT_MASK(bank) (0x000000a0 + ((bank) << 2)) -#define GPIO_INT_MSKCLR(bank) (0x000000c0 + ((bank) << 2)) -#define GPIO_CONTROL(bank) (0x00000100 + ((bank) << 2)) -#define GPIO_PWD_STATUS(bank) (0x00000500 + ((bank) << 2)) - -#define GPIO_GPPWR_OFFSET 0x00000520 - -#define GPIO_GPCTR0_DBR_SHIFT 5 -#define GPIO_GPCTR0_DBR_MASK 0x000001e0 - -#define GPIO_GPCTR0_ITR_SHIFT 3 -#define GPIO_GPCTR0_ITR_MASK 0x00000018 -#define GPIO_GPCTR0_ITR_CMD_RISING_EDGE 0x00000001 -#define GPIO_GPCTR0_ITR_CMD_FALLING_EDGE 0x00000002 -#define GPIO_GPCTR0_ITR_CMD_BOTH_EDGE 0x00000003 - -#define GPIO_GPCTR0_IOTR_MASK 0x00000001 -#define GPIO_GPCTR0_IOTR_CMD_0UTPUT 0x00000000 -#define GPIO_GPCTR0_IOTR_CMD_INPUT 0x00000001 - -int gpio_request(unsigned gpio, const char *label) -{ - unsigned int value, off; - - writel(GPIO_PASSWD, GPIO_BASE + GPIO_GPPWR_OFFSET); - off = GPIO_PWD_STATUS(GPIO_BANK(gpio)); - value = readl(GPIO_BASE + off) & ~GPIO_BITMASK(gpio); - writel(value, GPIO_BASE + off); - - return 0; -} - -int gpio_free(unsigned gpio) -{ - unsigned int value, off; - - writel(GPIO_PASSWD, GPIO_BASE + GPIO_GPPWR_OFFSET); - off = GPIO_PWD_STATUS(GPIO_BANK(gpio)); - value = readl(GPIO_BASE + off) | GPIO_BITMASK(gpio); - writel(value, GPIO_BASE + off); - - return 0; -} - -int gpio_direction_input(unsigned gpio) -{ - u32 val; - - val = readl(GPIO_BASE + GPIO_CONTROL(gpio)); - val &= ~GPIO_GPCTR0_IOTR_MASK; - val |= GPIO_GPCTR0_IOTR_CMD_INPUT; - writel(val, GPIO_BASE + GPIO_CONTROL(gpio)); - - return 0; -} - -int gpio_direction_output(unsigned gpio, int value) -{ - int bank_id = GPIO_BANK(gpio); - int bitmask = GPIO_BITMASK(gpio); - u32 val, off; - - val = readl(GPIO_BASE + GPIO_CONTROL(gpio)); - val &= ~GPIO_GPCTR0_IOTR_MASK; - val |= GPIO_GPCTR0_IOTR_CMD_0UTPUT; - writel(val, GPIO_BASE + GPIO_CONTROL(gpio)); - off = value ? GPIO_OUT_SET(bank_id) : GPIO_OUT_CLEAR(bank_id); - - val = readl(GPIO_BASE + off); - val |= bitmask; - writel(val, GPIO_BASE + off); - - return 0; -} - -int gpio_get_value(unsigned gpio) -{ - int bank_id = GPIO_BANK(gpio); - int bitmask = GPIO_BITMASK(gpio); - u32 val, off; - - /* determine the GPIO pin direction */ - val = readl(GPIO_BASE + GPIO_CONTROL(gpio)); - val &= GPIO_GPCTR0_IOTR_MASK; - - /* read the GPIO bank status */ - off = (GPIO_GPCTR0_IOTR_CMD_INPUT == val) ? - GPIO_IN_STATUS(bank_id) : GPIO_OUT_STATUS(bank_id); - val = readl(GPIO_BASE + off); - - /* return the specified bit status */ - return !!(val & bitmask); -} - -void gpio_set_value(unsigned gpio, int value) -{ - int bank_id = GPIO_BANK(gpio); - int bitmask = GPIO_BITMASK(gpio); - u32 val, off; - - /* determine the GPIO pin direction */ - val = readl(GPIO_BASE + GPIO_CONTROL(gpio)); - val &= GPIO_GPCTR0_IOTR_MASK; - - /* this function only applies to output pin */ - if (GPIO_GPCTR0_IOTR_CMD_INPUT == val) { - printf("%s: Cannot set an input pin %d\n", __func__, gpio); - return; - } - - off = value ? GPIO_OUT_SET(bank_id) : GPIO_OUT_CLEAR(bank_id); - - val = readl(GPIO_BASE + off); - val |= bitmask; - writel(val, GPIO_BASE + off); -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 29/76] video: Drop unused lg4573 driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (27 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 28/76] arm: Drop old kona code Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 30/76] m68k: Drop unused CONFIG_M52277 Simon Glass ` (43 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Anatolij Gustschin This is not used since this commit: 3cf02f5ffa4 imx6: remove not longer supported aristainetos boards Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/video/Makefile | 1 - drivers/video/lg4573.c | 331 ----------------------------------------- 2 files changed, 332 deletions(-) delete mode 100644 drivers/video/lg4573.c diff --git a/drivers/video/Makefile b/drivers/video/Makefile index 40a871d638e..12b68cdd068 100644 --- a/drivers/video/Makefile +++ b/drivers/video/Makefile @@ -30,7 +30,6 @@ obj-${CONFIG_VIDEO_TEGRA124} += tegra124/ obj-$(CONFIG_ATMEL_HLCD) += atmel_hlcdfb.o obj-$(CONFIG_ATMEL_LCD) += atmel_lcdfb.o obj-$(CONFIG_IHS_VIDEO_OUT) += ihs_video_out.o -obj-$(CONFIG_LG4573) += lg4573.o obj-$(CONFIG_LOGICORE_DP_TX) += logicore_dp_tx.o obj-$(CONFIG_NXP_TDA19988) += tda19988.o obj-$(CONFIG_OSD) += video_osd-uclass.o diff --git a/drivers/video/lg4573.c b/drivers/video/lg4573.c deleted file mode 100644 index dd87fc461b9..00000000000 --- a/drivers/video/lg4573.c +++ /dev/null @@ -1,331 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * LCD: LG4573, TFT 4.3", 480x800, RGB24 - * LCD initialization via SPI - * - */ -#include <common.h> -#include <backlight.h> -#include <command.h> -#include <display.h> -#include <dm.h> -#include <log.h> -#include <dm/read.h> -#include <dm/uclass-internal.h> -#include <errno.h> -#include <spi.h> -#include <asm/gpio.h> -#include <linux/delay.h> - -#define PWR_ON_DELAY_MSECS 120 - -static int lb043wv_spi_write_u16(struct spi_slave *slave, u16 val) -{ - unsigned short buf16 = htons(val); - int ret = 0; - - ret = spi_xfer(slave, 16, &buf16, NULL, - SPI_XFER_BEGIN | SPI_XFER_END); - if (ret) - debug("%s: Failed to send: %d\n", __func__, ret); - - return ret; -} - -static void lb043wv_spi_write_u16_array(struct spi_slave *slave, u16 *buff, - int size) -{ - int i; - - for (i = 0; i < size; i++) - lb043wv_spi_write_u16(slave, buff[i]); -} - -static void lb043wv_display_mode_settings(struct spi_slave *slave) -{ - static u16 display_mode_settings[] = { - 0x703A, - 0x7270, - 0x70B1, - 0x7208, - 0x723B, - 0x720F, - 0x70B2, - 0x7200, - 0x72C8, - 0x70B3, - 0x7200, - 0x70B4, - 0x7200, - 0x70B5, - 0x7242, - 0x7210, - 0x7210, - 0x7200, - 0x7220, - 0x70B6, - 0x720B, - 0x720F, - 0x723C, - 0x7213, - 0x7213, - 0x72E8, - 0x70B7, - 0x7246, - 0x7206, - 0x720C, - 0x7200, - 0x7200, - }; - - debug("transfer display mode settings\n"); - lb043wv_spi_write_u16_array(slave, display_mode_settings, - ARRAY_SIZE(display_mode_settings)); -} - -static void lb043wv_power_settings(struct spi_slave *slave) -{ - static u16 power_settings[] = { - 0x70C0, - 0x7201, - 0x7211, - 0x70C3, - 0x7207, - 0x7203, - 0x7204, - 0x7204, - 0x7204, - 0x70C4, - 0x7212, - 0x7224, - 0x7218, - 0x7218, - 0x7202, - 0x7249, - 0x70C5, - 0x726F, - 0x70C6, - 0x7241, - 0x7263, - }; - - debug("transfer power settings\n"); - lb043wv_spi_write_u16_array(slave, power_settings, - ARRAY_SIZE(power_settings)); -} - -static void lb043wv_gamma_settings(struct spi_slave *slave) -{ - static u16 gamma_settings[] = { - 0x70D0, - 0x7203, - 0x7207, - 0x7273, - 0x7235, - 0x7200, - 0x7201, - 0x7220, - 0x7200, - 0x7203, - 0x70D1, - 0x7203, - 0x7207, - 0x7273, - 0x7235, - 0x7200, - 0x7201, - 0x7220, - 0x7200, - 0x7203, - 0x70D2, - 0x7203, - 0x7207, - 0x7273, - 0x7235, - 0x7200, - 0x7201, - 0x7220, - 0x7200, - 0x7203, - 0x70D3, - 0x7203, - 0x7207, - 0x7273, - 0x7235, - 0x7200, - 0x7201, - 0x7220, - 0x7200, - 0x7203, - 0x70D4, - 0x7203, - 0x7207, - 0x7273, - 0x7235, - 0x7200, - 0x7201, - 0x7220, - 0x7200, - 0x7203, - 0x70D5, - 0x7203, - 0x7207, - 0x7273, - 0x7235, - 0x7200, - 0x7201, - 0x7220, - 0x7200, - 0x7203, - }; - - debug("transfer gamma settings\n"); - lb043wv_spi_write_u16_array(slave, gamma_settings, - ARRAY_SIZE(gamma_settings)); -} - -static void lb043wv_display_on(struct spi_slave *slave) -{ - static u16 sleep_out = 0x7011; - static u16 display_on = 0x7029; - - lb043wv_spi_write_u16(slave, sleep_out); - mdelay(PWR_ON_DELAY_MSECS); - lb043wv_spi_write_u16(slave, display_on); -} - -static int lg4573_spi_startup(struct spi_slave *slave) -{ - int ret; - - ret = spi_claim_bus(slave); - if (ret) - return ret; - - lb043wv_display_mode_settings(slave); - lb043wv_power_settings(slave); - lb043wv_gamma_settings(slave); - lb043wv_display_on(slave); - - spi_release_bus(slave); - return 0; -} - -static int do_lgset(struct cmd_tbl *cmdtp, int flag, int argc, - char *const argv[]) -{ - struct spi_slave *slave; - struct udevice *dev; - int ret; - - ret = uclass_get_device_by_driver(UCLASS_DISPLAY, - DM_DRIVER_GET(lg4573_lcd), &dev); - if (ret) { - printf("%s: Could not get lg4573 device\n", __func__); - return ret; - } - slave = dev_get_parent_priv(dev); - if (!slave) { - printf("%s: No slave data\n", __func__); - return -ENODEV; - } - lg4573_spi_startup(slave); - - return 0; -} - -U_BOOT_CMD( - lgset, 2, 1, do_lgset, - "set lgdisplay", - "" -); - -static int lg4573_bind(struct udevice *dev) -{ - return 0; -} - -static int lg4573_probe(struct udevice *dev) -{ - return 0; -} - -static const struct udevice_id lg4573_ids[] = { - { .compatible = "lg,lg4573" }, - { } -}; - -struct lg4573_lcd_priv { - struct display_timing timing; - struct udevice *backlight; - struct gpio_desc enable; - int panel_bpp; - u32 power_on_delay; -}; - -static int lg4573_lcd_read_timing(struct udevice *dev, - struct display_timing *timing) -{ - struct lg4573_lcd_priv *priv = dev_get_priv(dev); - - memcpy(timing, &priv->timing, sizeof(struct display_timing)); - - return 0; -} - -static int lg4573_lcd_enable(struct udevice *dev, int bpp, - const struct display_timing *edid) -{ - struct spi_slave *slave = dev_get_parent_priv(dev); - struct lg4573_lcd_priv *priv = dev_get_priv(dev); - int ret = 0; - - dm_gpio_set_value(&priv->enable, 1); - ret = backlight_enable(priv->backlight); - - mdelay(priv->power_on_delay); - lg4573_spi_startup(slave); - - return ret; -}; - -static const struct dm_display_ops lg4573_lcd_ops = { - .read_timing = lg4573_lcd_read_timing, - .enable = lg4573_lcd_enable, -}; - -static int lg4573_of_to_plat(struct udevice *dev) -{ - struct lg4573_lcd_priv *priv = dev_get_priv(dev); - int ret; - - ret = uclass_get_device_by_phandle(UCLASS_PANEL_BACKLIGHT, dev, - "backlight", &priv->backlight); - if (ret) { - debug("%s: Cannot get backlight: ret=%d\n", __func__, ret); - return log_ret(ret); - } - ret = gpio_request_by_name(dev, "enable-gpios", 0, &priv->enable, - GPIOD_IS_OUT); - if (ret) { - debug("%s: Warning: cannot get enable GPIO: ret=%d\n", - __func__, ret); - if (ret != -ENOENT) - return log_ret(ret); - } - - priv->power_on_delay = dev_read_u32_default(dev, "power-on-delay", 10); - - return 0; -} - -U_BOOT_DRIVER(lg4573_lcd) = { - .name = "lg4573", - .id = UCLASS_DISPLAY, - .ops = &lg4573_lcd_ops, - .of_to_plat = lg4573_of_to_plat, - .of_match = lg4573_ids, - .bind = lg4573_bind, - .probe = lg4573_probe, - .priv_auto = sizeof(struct lg4573_lcd_priv), -}; -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 30/76] m68k: Drop unused CONFIG_M52277 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (28 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 29/76] video: Drop unused lg4573 driver Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 31/76] m68k: Drop unused CONFIG_MACH_DAVINCI_DA830_EVM Simon Glass ` (42 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Alison Wang, Angelo Dureghello This option does not exist, so the Makefile rule does nothing. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/m68k/Makefile | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/m68k/Makefile b/arch/m68k/Makefile index 63f18109a57..4a7960bbeb4 100644 --- a/arch/m68k/Makefile +++ b/arch/m68k/Makefile @@ -7,7 +7,6 @@ libs-y += arch/m68k/lib/ cpuflags-$(CONFIG_M5208) := -mcpu=5208 cpuflags-$(CONFIG_M5235) := -mcpu=5235 -fPIC -cpuflags-$(CONFIG_M52277) := -mcpu=52277 -fPIC cpuflags-$(CONFIG_M5249) := -mcpu=5249 cpuflags-$(CONFIG_M5253) := -mcpu=5253 cpuflags-$(CONFIG_M5271) := -mcpu=5271 -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 31/76] m68k: Drop unused CONFIG_MACH_DAVINCI_DA830_EVM 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (29 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 30/76] m68k: Drop unused CONFIG_M52277 Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 32/76] arm: Drop CONFIG_MMU Simon Glass ` (41 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Alison Wang, Angelo Dureghello This option does not exist, so the Makefile rule does nothing. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) board/davinci/da8xxevm/Makefile | 1 - 1 file changed, 1 deletion(-) diff --git a/board/davinci/da8xxevm/Makefile b/board/davinci/da8xxevm/Makefile index 8187c8db22e..fe043d517f2 100644 --- a/board/davinci/da8xxevm/Makefile +++ b/board/davinci/da8xxevm/Makefile @@ -5,6 +5,5 @@ # # Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> -obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += da830evm.o obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += da850evm.o obj-$(CONFIG_TARGET_OMAPL138_LCDK) += omapl138_lcdk.o -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 32/76] arm: Drop CONFIG_MMU 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (30 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 31/76] m68k: Drop unused CONFIG_MACH_DAVINCI_DA830_EVM Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 33/76] arc: " Simon Glass ` (40 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This option does not exist, so the #ifdefs do nothing. Drop this code. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/arm/lib/debug.S | 21 --------------------- 1 file changed, 21 deletions(-) diff --git a/arch/arm/lib/debug.S b/arch/arm/lib/debug.S index 5983f2c04ce..af4beb4d9d2 100644 --- a/arch/arm/lib/debug.S +++ b/arch/arm/lib/debug.S @@ -21,22 +21,10 @@ #include CONFIG_DEBUG_LL_INCLUDE #endif -#ifdef CONFIG_MMU - .macro addruart_current, rx, tmp1, tmp2 - addruart \tmp1, \tmp2, \rx - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 - moveq \rx, \tmp1 - movne \rx, \tmp2 - .endm - -#else /* !CONFIG_MMU */ .macro addruart_current, rx, tmp1, tmp2 addruart \rx, \tmp1, \tmp2 .endm -#endif /* CONFIG_MMU */ - /* * Useful debugging routines */ @@ -97,15 +85,6 @@ ENTRY(printch) b 1b ENDPROC(printch) -#ifdef CONFIG_MMU -ENTRY(debug_ll_addr) - addruart r2, r3, ip - str r2, [r0] - str r3, [r1] - mov pc, lr -ENDPROC(debug_ll_addr) -#endif - #else ENTRY(printascii) -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 33/76] arc: Drop CONFIG_MMU 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (31 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 32/76] arm: Drop CONFIG_MMU Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 34/76] gpio: Drop unused mpc83xx_gpio driver Simon Glass ` (39 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Alexey Brodkin This option is set in the Makefile but has no effect in the assembly code, i.e. the #ifdef branch is never used. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/arc/config.mk | 4 ---- arch/arc/lib/ints_low.S | 5 ----- 2 files changed, 9 deletions(-) diff --git a/arch/arc/config.mk b/arch/arc/config.mk index b713fa3054c..b110f7deaf6 100644 --- a/arch/arc/config.mk +++ b/arch/arc/config.mk @@ -12,10 +12,6 @@ KBUILD_LDFLAGS += -EB PLATFORM_CPPFLAGS += -mbig-endian endif -ifdef CONFIG_ARC_MMU_VER -CONFIG_MMU = 1 -endif - PLATFORM_CPPFLAGS += -ffixed-r25 -D__ARC__ -gdwarf-2 -mno-sdata PLATFORM_RELFLAGS += -ffunction-sections -fdata-sections -fno-common diff --git a/arch/arc/lib/ints_low.S b/arch/arc/lib/ints_low.S index 38c45c60a95..fb283f239ea 100644 --- a/arch/arc/lib/ints_low.S +++ b/arch/arc/lib/ints_low.S @@ -76,13 +76,8 @@ .endm .macro SAVE_EXCEPTION_SOURCE -#ifdef CONFIG_MMU - /* If MMU exists exception faulting address is loaded in EFA reg */ - lr %r0, [%efa] -#else /* Otherwise in ERET (exception return) reg */ lr %r0, [%eret] -#endif .endm ENTRY(memory_error) -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 34/76] gpio: Drop unused mpc83xx_gpio driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (32 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 33/76] arc: " Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 35/76] imx: Rename CONFIG_MXS to CFG_MXS Simon Glass ` (38 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used since this commit: 7458f18e5c2 ppc: Remove MPC8313ERDB boards Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/gpio/Makefile | 1 - drivers/gpio/mpc83xx_gpio.c | 183 ------------------------------------ 2 files changed, 184 deletions(-) delete mode 100644 drivers/gpio/mpc83xx_gpio.c diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index ec65f70c318..889a88dc885 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -38,7 +38,6 @@ obj-$(CONFIG_TEGRA_GPIO) += tegra_gpio.o obj-$(CONFIG_TEGRA186_GPIO) += tegra186_gpio.o obj-$(CONFIG_DA8XX_GPIO) += da8xx_gpio.o obj-$(CONFIG_ALTERA_PIO) += altera_pio.o -obj-$(CONFIG_MPC83XX_GPIO) += mpc83xx_gpio.o obj-$(CONFIG_MPC8XXX_GPIO) += mpc8xxx_gpio.o obj-$(CONFIG_MPC83XX_SPISEL_BOOT) += mpc83xx_spisel_boot.o obj-$(CONFIG_SH_GPIO_PFC) += sh_pfc.o diff --git a/drivers/gpio/mpc83xx_gpio.c b/drivers/gpio/mpc83xx_gpio.c deleted file mode 100644 index bf693c8d457..00000000000 --- a/drivers/gpio/mpc83xx_gpio.c +++ /dev/null @@ -1,183 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Freescale MPC83xx GPIO handling. - */ - -#include <common.h> -#include <malloc.h> -#include <mpc83xx.h> -#include <asm/gpio.h> -#include <asm/io.h> - -#ifndef CFG_MPC83XX_GPIO_0_INIT_DIRECTION -#define CFG_MPC83XX_GPIO_0_INIT_DIRECTION 0 -#endif -#ifndef CFG_MPC83XX_GPIO_1_INIT_DIRECTION -#define CFG_MPC83XX_GPIO_1_INIT_DIRECTION 0 -#endif -#ifndef CFG_MPC83XX_GPIO_0_INIT_OPEN_DRAIN -#define CFG_MPC83XX_GPIO_0_INIT_OPEN_DRAIN 0 -#endif -#ifndef CFG_MPC83XX_GPIO_1_INIT_OPEN_DRAIN -#define CFG_MPC83XX_GPIO_1_INIT_OPEN_DRAIN 0 -#endif -#ifndef CFG_MPC83XX_GPIO_0_INIT_VALUE -#define CFG_MPC83XX_GPIO_0_INIT_VALUE 0 -#endif -#ifndef CFG_MPC83XX_GPIO_1_INIT_VALUE -#define CFG_MPC83XX_GPIO_1_INIT_VALUE 0 -#endif - -static unsigned int gpio_output_value[MPC83XX_GPIO_CTRLRS]; - -/* - * Generic_GPIO primitives. - */ - -int gpio_request(unsigned gpio, const char *label) -{ - if (gpio >= MAX_NUM_GPIOS) - return -1; - - return 0; -} - -int gpio_free(unsigned gpio) -{ - /* Do not set to input */ - return 0; -} - -/* set GPIO pin 'gpio' as an input */ -int gpio_direction_input(unsigned gpio) -{ - immap_t *im = (immap_t *)CONFIG_SYS_IMMR; - unsigned int ctrlr; - unsigned int line; - unsigned int line_mask; - - /* 32-bits per controller */ - ctrlr = gpio >> 5; - line = gpio & (0x1F); - - /* Big endian */ - line_mask = 1 << (31 - line); - - clrbits_be32(&im->gpio[ctrlr].dir, line_mask); - - return 0; -} - -/* set GPIO pin 'gpio' as an output, with polarity 'value' */ -int gpio_direction_output(unsigned gpio, int value) -{ - immap_t *im = (immap_t *)CONFIG_SYS_IMMR; - unsigned int ctrlr; - unsigned int line; - unsigned int line_mask; - - if (value != 0 && value != 1) { - printf("Error: Value parameter must be 0 or 1.\n"); - return -1; - } - - gpio_set_value(gpio, value); - - /* 32-bits per controller */ - ctrlr = gpio >> 5; - line = gpio & (0x1F); - - /* Big endian */ - line_mask = 1 << (31 - line); - - /* Make the line output */ - setbits_be32(&im->gpio[ctrlr].dir, line_mask); - - return 0; -} - -/* read GPIO IN value of pin 'gpio' */ -int gpio_get_value(unsigned gpio) -{ - immap_t *im = (immap_t *)CONFIG_SYS_IMMR; - unsigned int ctrlr; - unsigned int line; - unsigned int line_mask; - - /* 32-bits per controller */ - ctrlr = gpio >> 5; - line = gpio & (0x1F); - - /* Big endian */ - line_mask = 1 << (31 - line); - - /* Read the value and mask off the bit */ - return (in_be32(&im->gpio[ctrlr].dat) & line_mask) != 0; -} - -/* write GPIO OUT value to pin 'gpio' */ -int gpio_set_value(unsigned gpio, int value) -{ - immap_t *im = (immap_t *)CONFIG_SYS_IMMR; - unsigned int ctrlr; - unsigned int line; - unsigned int line_mask; - - if (value != 0 && value != 1) { - printf("Error: Value parameter must be 0 or 1.\n"); - return -1; - } - - /* 32-bits per controller */ - ctrlr = gpio >> 5; - line = gpio & (0x1F); - - /* Big endian */ - line_mask = 1 << (31 - line); - - /* Update the local output buffer soft copy */ - gpio_output_value[ctrlr] = - (gpio_output_value[ctrlr] & ~line_mask) | \ - (value ? line_mask : 0); - - /* Write the output */ - out_be32(&im->gpio[ctrlr].dat, gpio_output_value[ctrlr]); - - return 0; -} - -/* Configure GPIO registers early */ -void mpc83xx_gpio_init_f(void) -{ - immap_t *im = (immap_t *)CONFIG_SYS_IMMR; - -#if MPC83XX_GPIO_CTRLRS >= 1 - out_be32(&im->gpio[0].dir, CFG_MPC83XX_GPIO_0_INIT_DIRECTION); - out_be32(&im->gpio[0].odr, CFG_MPC83XX_GPIO_0_INIT_OPEN_DRAIN); - out_be32(&im->gpio[0].dat, CFG_MPC83XX_GPIO_0_INIT_VALUE); - out_be32(&im->gpio[0].ier, 0xFFFFFFFF); /* Clear all events */ - out_be32(&im->gpio[0].imr, 0); - out_be32(&im->gpio[0].icr, 0); -#endif - -#if MPC83XX_GPIO_CTRLRS >= 2 - out_be32(&im->gpio[1].dir, CFG_MPC83XX_GPIO_1_INIT_DIRECTION); - out_be32(&im->gpio[1].odr, CFG_MPC83XX_GPIO_1_INIT_OPEN_DRAIN); - out_be32(&im->gpio[1].dat, CFG_MPC83XX_GPIO_1_INIT_VALUE); - out_be32(&im->gpio[1].ier, 0xFFFFFFFF); /* Clear all events */ - out_be32(&im->gpio[1].imr, 0); - out_be32(&im->gpio[1].icr, 0); -#endif -} - -/* Initialize GPIO soft-copies */ -void mpc83xx_gpio_init_r(void) -{ -#if MPC83XX_GPIO_CTRLRS >= 1 - gpio_output_value[0] = CFG_MPC83XX_GPIO_0_INIT_VALUE; -#endif - -#if MPC83XX_GPIO_CTRLRS >= 2 - gpio_output_value[1] = CFG_MPC83XX_GPIO_1_INIT_VALUE; -#endif -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 35/76] imx: Rename CONFIG_MXS to CFG_MXS 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (33 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 34/76] gpio: Drop unused mpc83xx_gpio driver Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 36/76] nand: Drop unused actl_nand driver Simon Glass ` (37 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Stefano Babic This is not a Kconfig option so we should not be setting it in the Makefile. Rename it to use a CFS_ prefix, since this is still used in mxsimage.c In general tools should support all the features without reference to CONFIG options, but this is left to the maintainer to look at. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) tools/Makefile | 4 ++-- tools/mxsimage.c | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/tools/Makefile b/tools/Makefile index edfa40903d9..2ee43dff542 100644 --- a/tools/Makefile +++ b/tools/Makefile @@ -158,9 +158,9 @@ fit_check_sign-objs := $(dumpimage-mkimage-objs) fit_check_sign.o file2include-objs := file2include.o ifneq ($(CONFIG_MX23)$(CONFIG_MX28)$(CONFIG_TOOLS_LIBCRYPTO),) -# Add CONFIG_MXS into host CFLAGS, so we can check whether or not register +# Add CFG_MXS into host CFLAGS, so we can check whether or not register # the mxsimage support within tools/mxsimage.c . -HOSTCFLAGS_mxsimage.o += -DCONFIG_MXS +HOSTCFLAGS_mxsimage.o += -DCFG_MXS endif ifdef CONFIG_TOOLS_LIBCRYPTO diff --git a/tools/mxsimage.c b/tools/mxsimage.c index fee022aab46..fbe46c47fae 100644 --- a/tools/mxsimage.c +++ b/tools/mxsimage.c @@ -5,7 +5,7 @@ * Copyright (C) 2012-2013 Marek Vasut <marex@denx.de> */ -#ifdef CONFIG_MXS +#ifdef CFG_MXS #include <errno.h> #include <fcntl.h> -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 36/76] nand: Drop unused actl_nand driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (34 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 35/76] imx: Rename CONFIG_MXS to CFG_MXS Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 37/76] mtd: Drop unused fsl_upm driver Simon Glass ` (36 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used since this commit: ed7fe2bee12 ppc: Remove xpedite boards Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) board/xes/common/Makefile | 1 - board/xes/common/actl_nand.c | 49 ------------------------------------ 2 files changed, 50 deletions(-) delete mode 100644 board/xes/common/actl_nand.c diff --git a/board/xes/common/Makefile b/board/xes/common/Makefile index 002821916c4..b00accca1be 100644 --- a/board/xes/common/Makefile +++ b/board/xes/common/Makefile @@ -7,4 +7,3 @@ obj-$(CONFIG_MPC86xx) += fsl_8xxx_clk.o obj-$(CONFIG_ARCH_P2020) += fsl_8xxx_clk.o obj-$(CONFIG_MPC85xx) += fsl_8xxx_misc.o board.o obj-$(CONFIG_MPC86xx) += fsl_8xxx_misc.o board.o -obj-$(CONFIG_NAND_ACTL) += actl_nand.o diff --git a/board/xes/common/actl_nand.c b/board/xes/common/actl_nand.c deleted file mode 100644 index 2d8a57576a6..00000000000 --- a/board/xes/common/actl_nand.c +++ /dev/null @@ -1,49 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2008 Extreme Engineering Solutions, Inc. - * - * This driver support NAND devices which have address lines - * connected as ALE and CLE inputs. - */ - -#include <common.h> -#include <nand.h> -#include <linux/mtd/rawnand.h> -#include <asm/io.h> - -/* - * Hardware specific access to control-lines - */ -static void nand_addr_hwcontrol(struct mtd_info *mtd, int cmd, uint ctrl) -{ - struct nand_chip *this = mtd_to_nand(mtd); - ulong IO_ADDR_W; - - if (ctrl & NAND_CTRL_CHANGE) { - IO_ADDR_W = (ulong)this->IO_ADDR_W; - - IO_ADDR_W &= ~(CONFIG_SYS_NAND_ACTL_CLE | - CONFIG_SYS_NAND_ACTL_ALE | - CONFIG_SYS_NAND_ACTL_NCE); - if (ctrl & NAND_CLE) - IO_ADDR_W |= CONFIG_SYS_NAND_ACTL_CLE; - if (ctrl & NAND_ALE) - IO_ADDR_W |= CONFIG_SYS_NAND_ACTL_ALE; - if (ctrl & NAND_NCE) - IO_ADDR_W |= CONFIG_SYS_NAND_ACTL_NCE; - - this->IO_ADDR_W = (void *)IO_ADDR_W; - } - - if (cmd != NAND_CMD_NONE) - writeb(cmd, this->IO_ADDR_W); -} - -int board_nand_init(struct nand_chip *nand) -{ - nand->ecc.mode = NAND_ECC_SOFT; - nand->cmd_ctrl = nand_addr_hwcontrol; - nand->chip_delay = CONFIG_SYS_NAND_ACTL_DELAY; - - return 0; -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 37/76] mtd: Drop unused fsl_upm driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (35 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 36/76] nand: Drop unused actl_nand driver Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 38/76] mtd: Drop unused fsmc_nand driver Simon Glass ` (35 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Michael Trimarchi This is not used since this commit: 8d1e3cb1400 powerpc: mpc83xx: remove MPC8360ERDK, EMPC8360EMDS support Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-By: Michael Trimarchi <michael@amarulasolutions.com> --- (no changes since v1) drivers/mtd/nand/raw/Makefile | 1 - drivers/mtd/nand/raw/fsl_upm.c | 187 --------------------------------- include/linux/mtd/fsl_upm.h | 44 -------- 3 files changed, 232 deletions(-) delete mode 100644 drivers/mtd/nand/raw/fsl_upm.c delete mode 100644 include/linux/mtd/fsl_upm.h diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile index 4c59903aa8c..e8764cf358b 100644 --- a/drivers/mtd/nand/raw/Makefile +++ b/drivers/mtd/nand/raw/Makefile @@ -56,7 +56,6 @@ obj-$(CONFIG_NAND_DENALI) += denali.o obj-$(CONFIG_NAND_DENALI_DT) += denali_dt.o obj-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_nand.o obj-$(CONFIG_NAND_FSL_IFC) += fsl_ifc_nand.o -obj-$(CONFIG_NAND_FSL_UPM) += fsl_upm.o obj-$(CONFIG_NAND_FSMC) += fsmc_nand.o obj-$(CONFIG_NAND_KB9202) += kb9202_nand.o obj-$(CONFIG_NAND_KIRKWOOD) += kirkwood_nand.o diff --git a/drivers/mtd/nand/raw/fsl_upm.c b/drivers/mtd/nand/raw/fsl_upm.c deleted file mode 100644 index 91cc1339537..00000000000 --- a/drivers/mtd/nand/raw/fsl_upm.c +++ /dev/null @@ -1,187 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * FSL UPM NAND driver - * - * Copyright (C) 2007 MontaVista Software, Inc. - * Anton Vorontsov <avorontsov@ru.mvista.com> - */ - -#include <config.h> -#include <common.h> -#include <log.h> -#include <asm/io.h> -#include <linux/delay.h> -#include <linux/errno.h> -#include <linux/mtd/mtd.h> -#include <linux/mtd/rawnand.h> -#include <linux/mtd/fsl_upm.h> -#include <nand.h> - -static void fsl_upm_start_pattern(struct fsl_upm *upm, u32 pat_offset) -{ - clrsetbits_be32(upm->mxmr, MxMR_MAD_MSK, MxMR_OP_RUNP | pat_offset); - (void)in_be32(upm->mxmr); -} - -static void fsl_upm_end_pattern(struct fsl_upm *upm) -{ - clrbits_be32(upm->mxmr, MxMR_OP_RUNP); - - while (in_be32(upm->mxmr) & MxMR_OP_RUNP) - eieio(); -} - -static void fsl_upm_run_pattern(struct fsl_upm *upm, int width, - void __iomem *io_addr, u32 mar) -{ - out_be32(upm->mar, mar); - (void)in_be32(upm->mar); - switch (width) { - case 8: - out_8(io_addr, 0x0); - break; - case 16: - out_be16(io_addr, 0x0); - break; - case 32: - out_be32(io_addr, 0x0); - break; - } -} - -static void fun_wait(struct fsl_upm_nand *fun) -{ - if (fun->dev_ready) { - while (!fun->dev_ready(fun->chip_nr)) - debug("unexpected busy state\n"); - } else { - /* - * If the R/B pin is not connected, - * a short delay is necessary. - */ - udelay(1); - } -} - -#if CONFIG_SYS_NAND_MAX_CHIPS > 1 -static void fun_select_chip(struct mtd_info *mtd, int chip_nr) -{ - struct nand_chip *chip = mtd_to_nand(mtd); - struct fsl_upm_nand *fun = nand_get_controller_data(chip); - - if (chip_nr >= 0) { - fun->chip_nr = chip_nr; - chip->IO_ADDR_R = chip->IO_ADDR_W = - fun->upm.io_addr + fun->chip_offset * chip_nr; - } else if (chip_nr == -1) { - chip->cmd_ctrl(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE); - } -} -#endif - -static void fun_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) -{ - struct nand_chip *chip = mtd_to_nand(mtd); - struct fsl_upm_nand *fun = nand_get_controller_data(chip); - void __iomem *io_addr; - u32 mar; - - if (!(ctrl & fun->last_ctrl)) { - fsl_upm_end_pattern(&fun->upm); - - if (cmd == NAND_CMD_NONE) - return; - - fun->last_ctrl = ctrl & (NAND_ALE | NAND_CLE); - } - - if (ctrl & NAND_CTRL_CHANGE) { - if (ctrl & NAND_ALE) - fsl_upm_start_pattern(&fun->upm, fun->upm_addr_offset); - else if (ctrl & NAND_CLE) - fsl_upm_start_pattern(&fun->upm, fun->upm_cmd_offset); - } - - mar = cmd << (32 - fun->width); - io_addr = fun->upm.io_addr; -#if CONFIG_SYS_NAND_MAX_CHIPS > 1 - if (fun->chip_nr > 0) { - io_addr += fun->chip_offset * fun->chip_nr; - if (fun->upm_mar_chip_offset) - mar |= fun->upm_mar_chip_offset * fun->chip_nr; - } -#endif - fsl_upm_run_pattern(&fun->upm, fun->width, io_addr, mar); - - /* - * Some boards/chips needs this. At least the MPC8360E-RDK - * needs it. Probably weird chip, because I don't see any - * need for this on MPC8555E + Samsung K9F1G08U0A. Usually - * here are 0-2 unexpected busy states per block read. - */ - if (fun->wait_flags & FSL_UPM_WAIT_RUN_PATTERN) - fun_wait(fun); -} - -static u8 upm_nand_read_byte(struct mtd_info *mtd) -{ - struct nand_chip *chip = mtd_to_nand(mtd); - - return in_8(chip->IO_ADDR_R); -} - -static void upm_nand_write_buf(struct mtd_info *mtd, const u_char *buf, int len) -{ - int i; - struct nand_chip *chip = mtd_to_nand(mtd); - struct fsl_upm_nand *fun = nand_get_controller_data(chip); - - for (i = 0; i < len; i++) { - out_8(chip->IO_ADDR_W, buf[i]); - if (fun->wait_flags & FSL_UPM_WAIT_WRITE_BYTE) - fun_wait(fun); - } - - if (fun->wait_flags & FSL_UPM_WAIT_WRITE_BUFFER) - fun_wait(fun); -} - -static void upm_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len) -{ - int i; - struct nand_chip *chip = mtd_to_nand(mtd); - - for (i = 0; i < len; i++) - buf[i] = in_8(chip->IO_ADDR_R); -} - -static int nand_dev_ready(struct mtd_info *mtd) -{ - struct nand_chip *chip = mtd_to_nand(mtd); - struct fsl_upm_nand *fun = nand_get_controller_data(chip); - - return fun->dev_ready(fun->chip_nr); -} - -int fsl_upm_nand_init(struct nand_chip *chip, struct fsl_upm_nand *fun) -{ - if (fun->width != 8 && fun->width != 16 && fun->width != 32) - return -ENOSYS; - - fun->last_ctrl = NAND_CLE; - - nand_set_controller_data(chip, fun); - chip->chip_delay = fun->chip_delay; - chip->ecc.mode = NAND_ECC_SOFT; - chip->cmd_ctrl = fun_cmd_ctrl; -#if CONFIG_SYS_NAND_MAX_CHIPS > 1 - chip->select_chip = fun_select_chip; -#endif - chip->read_byte = upm_nand_read_byte; - chip->read_buf = upm_nand_read_buf; - chip->write_buf = upm_nand_write_buf; - if (fun->dev_ready) - chip->dev_ready = nand_dev_ready; - - return 0; -} diff --git a/include/linux/mtd/fsl_upm.h b/include/linux/mtd/fsl_upm.h deleted file mode 100644 index 9999993543b..00000000000 --- a/include/linux/mtd/fsl_upm.h +++ /dev/null @@ -1,44 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * FSL UPM NAND driver - * - * Copyright (C) 2007 MontaVista Software, Inc. - * Anton Vorontsov <avorontsov@ru.mvista.com> - */ - -#ifndef __LINUX_MTD_NAND_FSL_UPM -#define __LINUX_MTD_NAND_FSL_UPM - -#include <linux/mtd/rawnand.h> - -#define FSL_UPM_WAIT_RUN_PATTERN 0x1 -#define FSL_UPM_WAIT_WRITE_BYTE 0x2 -#define FSL_UPM_WAIT_WRITE_BUFFER 0x4 - -struct fsl_upm { - void __iomem *mdr; - void __iomem *mxmr; - void __iomem *mar; - void __iomem *io_addr; -}; - -struct fsl_upm_nand { - struct fsl_upm upm; - - int width; - int upm_cmd_offset; - int upm_addr_offset; - int upm_mar_chip_offset; - int wait_flags; - int (*dev_ready)(int chip_nr); - int chip_delay; - int chip_offset; - int chip_nr; - - /* no need to fill */ - int last_ctrl; -}; - -extern int fsl_upm_nand_init(struct nand_chip *chip, struct fsl_upm_nand *fun); - -#endif -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 38/76] mtd: Drop unused fsmc_nand driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (36 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 37/76] mtd: Drop unused fsl_upm driver Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 40/76] mtd: Drop unused nand_plat driver Simon Glass ` (34 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Michael Trimarchi This is not used since this commit: 570c3dcfc15 arm: Remove spear600 boards and the rest of SPEAr support Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> --- (no changes since v1) drivers/mtd/nand/raw/Makefile | 1 - drivers/mtd/nand/raw/fsmc_nand.c | 470 ------------------------------- include/linux/mtd/fsmc_nand.h | 84 ------ 3 files changed, 555 deletions(-) delete mode 100644 drivers/mtd/nand/raw/fsmc_nand.c delete mode 100644 include/linux/mtd/fsmc_nand.h diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile index e8764cf358b..f004eb39f3b 100644 --- a/drivers/mtd/nand/raw/Makefile +++ b/drivers/mtd/nand/raw/Makefile @@ -56,7 +56,6 @@ obj-$(CONFIG_NAND_DENALI) += denali.o obj-$(CONFIG_NAND_DENALI_DT) += denali_dt.o obj-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_nand.o obj-$(CONFIG_NAND_FSL_IFC) += fsl_ifc_nand.o -obj-$(CONFIG_NAND_FSMC) += fsmc_nand.o obj-$(CONFIG_NAND_KB9202) += kb9202_nand.o obj-$(CONFIG_NAND_KIRKWOOD) += kirkwood_nand.o obj-$(CONFIG_NAND_KMETER1) += kmeter1_nand.o diff --git a/drivers/mtd/nand/raw/fsmc_nand.c b/drivers/mtd/nand/raw/fsmc_nand.c deleted file mode 100644 index d795864949c..00000000000 --- a/drivers/mtd/nand/raw/fsmc_nand.c +++ /dev/null @@ -1,470 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2010 - * Vipin Kumar, STMicroelectronics, vipin.kumar@st.com. - * - * (C) Copyright 2012 - * Amit Virdi, STMicroelectronics, amit.virdi@st.com. - */ - -#include <common.h> -#include <nand.h> -#include <asm/io.h> -#include <linux/bitops.h> -#include <linux/err.h> -#include <linux/mtd/nand_ecc.h> -#include <linux/mtd/rawnand.h> -#include <linux/mtd/fsmc_nand.h> -#include <asm/arch/hardware.h> - -static u32 fsmc_version; -static struct fsmc_regs *const fsmc_regs_p = (struct fsmc_regs *) - CONFIG_SYS_FSMC_BASE; - -/* - * ECC4 and ECC1 have 13 bytes and 3 bytes of ecc respectively for 512 bytes of - * data. ECC4 can correct up to 8 bits in 512 bytes of data while ECC1 can - * correct 1 bit in 512 bytes - */ - -static struct nand_ecclayout fsmc_ecc4_lp_layout = { - .eccbytes = 104, - .eccpos = { 2, 3, 4, 5, 6, 7, 8, - 9, 10, 11, 12, 13, 14, - 18, 19, 20, 21, 22, 23, 24, - 25, 26, 27, 28, 29, 30, - 34, 35, 36, 37, 38, 39, 40, - 41, 42, 43, 44, 45, 46, - 50, 51, 52, 53, 54, 55, 56, - 57, 58, 59, 60, 61, 62, - 66, 67, 68, 69, 70, 71, 72, - 73, 74, 75, 76, 77, 78, - 82, 83, 84, 85, 86, 87, 88, - 89, 90, 91, 92, 93, 94, - 98, 99, 100, 101, 102, 103, 104, - 105, 106, 107, 108, 109, 110, - 114, 115, 116, 117, 118, 119, 120, - 121, 122, 123, 124, 125, 126 - }, - .oobfree = { - {.offset = 15, .length = 3}, - {.offset = 31, .length = 3}, - {.offset = 47, .length = 3}, - {.offset = 63, .length = 3}, - {.offset = 79, .length = 3}, - {.offset = 95, .length = 3}, - {.offset = 111, .length = 3}, - {.offset = 127, .length = 1} - } -}; - -/* - * ECC4 layout for NAND of pagesize 4096 bytes & OOBsize 224 bytes. 13*8 bytes - * of OOB size is reserved for ECC, Byte no. 0 & 1 reserved for bad block & 118 - * bytes are free for use. - */ -static struct nand_ecclayout fsmc_ecc4_224_layout = { - .eccbytes = 104, - .eccpos = { 2, 3, 4, 5, 6, 7, 8, - 9, 10, 11, 12, 13, 14, - 18, 19, 20, 21, 22, 23, 24, - 25, 26, 27, 28, 29, 30, - 34, 35, 36, 37, 38, 39, 40, - 41, 42, 43, 44, 45, 46, - 50, 51, 52, 53, 54, 55, 56, - 57, 58, 59, 60, 61, 62, - 66, 67, 68, 69, 70, 71, 72, - 73, 74, 75, 76, 77, 78, - 82, 83, 84, 85, 86, 87, 88, - 89, 90, 91, 92, 93, 94, - 98, 99, 100, 101, 102, 103, 104, - 105, 106, 107, 108, 109, 110, - 114, 115, 116, 117, 118, 119, 120, - 121, 122, 123, 124, 125, 126 - }, - .oobfree = { - {.offset = 15, .length = 3}, - {.offset = 31, .length = 3}, - {.offset = 47, .length = 3}, - {.offset = 63, .length = 3}, - {.offset = 79, .length = 3}, - {.offset = 95, .length = 3}, - {.offset = 111, .length = 3}, - {.offset = 127, .length = 97} - } -}; - -/* - * ECC placement definitions in oobfree type format - * There are 13 bytes of ecc for every 512 byte block and it has to be read - * consecutively and immediately after the 512 byte data block for hardware to - * generate the error bit offsets in 512 byte data - * Managing the ecc bytes in the following way makes it easier for software to - * read ecc bytes consecutive to data bytes. This way is similar to - * oobfree structure maintained already in u-boot nand driver - */ -static struct fsmc_eccplace fsmc_eccpl_lp = { - .eccplace = { - {.offset = 2, .length = 13}, - {.offset = 18, .length = 13}, - {.offset = 34, .length = 13}, - {.offset = 50, .length = 13}, - {.offset = 66, .length = 13}, - {.offset = 82, .length = 13}, - {.offset = 98, .length = 13}, - {.offset = 114, .length = 13} - } -}; - -static struct nand_ecclayout fsmc_ecc4_sp_layout = { - .eccbytes = 13, - .eccpos = { 0, 1, 2, 3, 6, 7, 8, - 9, 10, 11, 12, 13, 14 - }, - .oobfree = { - {.offset = 15, .length = 1}, - } -}; - -static struct fsmc_eccplace fsmc_eccpl_sp = { - .eccplace = { - {.offset = 0, .length = 4}, - {.offset = 6, .length = 9} - } -}; - -static struct nand_ecclayout fsmc_ecc1_layout = { - .eccbytes = 24, - .eccpos = {2, 3, 4, 18, 19, 20, 34, 35, 36, 50, 51, 52, - 66, 67, 68, 82, 83, 84, 98, 99, 100, 114, 115, 116}, - .oobfree = { - {.offset = 8, .length = 8}, - {.offset = 24, .length = 8}, - {.offset = 40, .length = 8}, - {.offset = 56, .length = 8}, - {.offset = 72, .length = 8}, - {.offset = 88, .length = 8}, - {.offset = 104, .length = 8}, - {.offset = 120, .length = 8} - } -}; - -/* Count the number of 0's in buff upto a max of max_bits */ -static int count_written_bits(uint8_t *buff, int size, int max_bits) -{ - int k, written_bits = 0; - - for (k = 0; k < size; k++) { - written_bits += hweight8(~buff[k]); - if (written_bits > max_bits) - break; - } - - return written_bits; -} - -static void fsmc_nand_hwcontrol(struct mtd_info *mtd, int cmd, uint ctrl) -{ - struct nand_chip *this = mtd_to_nand(mtd); - ulong IO_ADDR_W; - - if (ctrl & NAND_CTRL_CHANGE) { - IO_ADDR_W = (ulong)this->IO_ADDR_W; - - IO_ADDR_W &= ~(CONFIG_SYS_NAND_CLE | CONFIG_SYS_NAND_ALE); - if (ctrl & NAND_CLE) - IO_ADDR_W |= CONFIG_SYS_NAND_CLE; - if (ctrl & NAND_ALE) - IO_ADDR_W |= CONFIG_SYS_NAND_ALE; - - if (ctrl & NAND_NCE) { - writel(readl(&fsmc_regs_p->pc) | - FSMC_ENABLE, &fsmc_regs_p->pc); - } else { - writel(readl(&fsmc_regs_p->pc) & - ~FSMC_ENABLE, &fsmc_regs_p->pc); - } - this->IO_ADDR_W = (void *)IO_ADDR_W; - } - - if (cmd != NAND_CMD_NONE) - writeb(cmd, this->IO_ADDR_W); -} - -static int fsmc_bch8_correct_data(struct mtd_info *mtd, u_char *dat, - u_char *read_ecc, u_char *calc_ecc) -{ - /* The calculated ecc is actually the correction index in data */ - u32 err_idx[8]; - u32 num_err, i; - u32 ecc1, ecc2, ecc3, ecc4; - - num_err = (readl(&fsmc_regs_p->sts) >> 10) & 0xF; - - if (likely(num_err == 0)) - return 0; - - if (unlikely(num_err > 8)) { - /* - * This is a temporary erase check. A newly erased page read - * would result in an ecc error because the oob data is also - * erased to FF and the calculated ecc for an FF data is not - * FF..FF. - * This is a workaround to skip performing correction in case - * data is FF..FF - * - * Logic: - * For every page, each bit written as 0 is counted until these - * number of bits are greater than 8 (the maximum correction - * capability of FSMC for each 512 + 13 bytes) - */ - - int bits_ecc = count_written_bits(read_ecc, 13, 8); - int bits_data = count_written_bits(dat, 512, 8); - - if ((bits_ecc + bits_data) <= 8) { - if (bits_data) - memset(dat, 0xff, 512); - return bits_data + bits_ecc; - } - - return -EBADMSG; - } - - ecc1 = readl(&fsmc_regs_p->ecc1); - ecc2 = readl(&fsmc_regs_p->ecc2); - ecc3 = readl(&fsmc_regs_p->ecc3); - ecc4 = readl(&fsmc_regs_p->sts); - - err_idx[0] = (ecc1 >> 0) & 0x1FFF; - err_idx[1] = (ecc1 >> 13) & 0x1FFF; - err_idx[2] = (((ecc2 >> 0) & 0x7F) << 6) | ((ecc1 >> 26) & 0x3F); - err_idx[3] = (ecc2 >> 7) & 0x1FFF; - err_idx[4] = (((ecc3 >> 0) & 0x1) << 12) | ((ecc2 >> 20) & 0xFFF); - err_idx[5] = (ecc3 >> 1) & 0x1FFF; - err_idx[6] = (ecc3 >> 14) & 0x1FFF; - err_idx[7] = (((ecc4 >> 16) & 0xFF) << 5) | ((ecc3 >> 27) & 0x1F); - - i = 0; - while (i < num_err) { - err_idx[i] ^= 3; - - if (err_idx[i] < 512 * 8) - __change_bit(err_idx[i], dat); - - i++; - } - - return num_err; -} - -static int fsmc_read_hwecc(struct mtd_info *mtd, - const u_char *data, u_char *ecc) -{ - u_int ecc_tmp; - int timeout = CONFIG_SYS_HZ; - ulong start; - - switch (fsmc_version) { - case FSMC_VER8: - start = get_timer(0); - while (get_timer(start) < timeout) { - /* - * Busy waiting for ecc computation - * to finish for 512 bytes - */ - if (readl(&fsmc_regs_p->sts) & FSMC_CODE_RDY) - break; - } - - ecc_tmp = readl(&fsmc_regs_p->ecc1); - ecc[0] = (u_char) (ecc_tmp >> 0); - ecc[1] = (u_char) (ecc_tmp >> 8); - ecc[2] = (u_char) (ecc_tmp >> 16); - ecc[3] = (u_char) (ecc_tmp >> 24); - - ecc_tmp = readl(&fsmc_regs_p->ecc2); - ecc[4] = (u_char) (ecc_tmp >> 0); - ecc[5] = (u_char) (ecc_tmp >> 8); - ecc[6] = (u_char) (ecc_tmp >> 16); - ecc[7] = (u_char) (ecc_tmp >> 24); - - ecc_tmp = readl(&fsmc_regs_p->ecc3); - ecc[8] = (u_char) (ecc_tmp >> 0); - ecc[9] = (u_char) (ecc_tmp >> 8); - ecc[10] = (u_char) (ecc_tmp >> 16); - ecc[11] = (u_char) (ecc_tmp >> 24); - - ecc_tmp = readl(&fsmc_regs_p->sts); - ecc[12] = (u_char) (ecc_tmp >> 16); - break; - - default: - ecc_tmp = readl(&fsmc_regs_p->ecc1); - ecc[0] = (u_char) (ecc_tmp >> 0); - ecc[1] = (u_char) (ecc_tmp >> 8); - ecc[2] = (u_char) (ecc_tmp >> 16); - break; - } - - return 0; -} - -void fsmc_enable_hwecc(struct mtd_info *mtd, int mode) -{ - writel(readl(&fsmc_regs_p->pc) & ~FSMC_ECCPLEN_256, - &fsmc_regs_p->pc); - writel(readl(&fsmc_regs_p->pc) & ~FSMC_ECCEN, - &fsmc_regs_p->pc); - writel(readl(&fsmc_regs_p->pc) | FSMC_ECCEN, - &fsmc_regs_p->pc); -} - -/* - * fsmc_read_page_hwecc - * @mtd: mtd info structure - * @chip: nand chip info structure - * @buf: buffer to store read data - * @oob_required: caller expects OOB data read to chip->oob_poi - * @page: page number to read - * - * This routine is needed for fsmc verison 8 as reading from NAND chip has to be - * performed in a strict sequence as follows: - * data(512 byte) -> ecc(13 byte) - * After this read, fsmc hardware generates and reports error data bits(upto a - * max of 8 bits) - */ -static int fsmc_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, - uint8_t *buf, int oob_required, int page) -{ - struct fsmc_eccplace *fsmc_eccpl; - int i, j, s, stat, eccsize = chip->ecc.size; - int eccbytes = chip->ecc.bytes; - int eccsteps = chip->ecc.steps; - uint8_t *p = buf; - uint8_t *ecc_calc = chip->buffers->ecccalc; - uint8_t *ecc_code = chip->buffers->ecccode; - int off, len, group = 0; - uint8_t oob[13] __attribute__ ((aligned (2))); - - /* Differentiate between small and large page ecc place definitions */ - if (mtd->writesize == 512) - fsmc_eccpl = &fsmc_eccpl_sp; - else - fsmc_eccpl = &fsmc_eccpl_lp; - - for (i = 0, s = 0; s < eccsteps; s++, i += eccbytes, p += eccsize) { - - chip->cmdfunc(mtd, NAND_CMD_READ0, s * eccsize, page); - chip->ecc.hwctl(mtd, NAND_ECC_READ); - chip->read_buf(mtd, p, eccsize); - - for (j = 0; j < eccbytes;) { - off = fsmc_eccpl->eccplace[group].offset; - len = fsmc_eccpl->eccplace[group].length; - group++; - - /* - * length is intentionally kept a higher multiple of 2 - * to read at least 13 bytes even in case of 16 bit NAND - * devices - */ - if (chip->options & NAND_BUSWIDTH_16) - len = roundup(len, 2); - chip->cmdfunc(mtd, NAND_CMD_READOOB, off, page); - chip->read_buf(mtd, oob + j, len); - j += len; - } - - memcpy(&ecc_code[i], oob, 13); - chip->ecc.calculate(mtd, p, &ecc_calc[i]); - - stat = chip->ecc.correct(mtd, p, &ecc_code[i], - &ecc_calc[i]); - if (stat < 0) - mtd->ecc_stats.failed++; - else - mtd->ecc_stats.corrected += stat; - } - - return 0; -} - -int fsmc_nand_init(struct nand_chip *nand) -{ - static int chip_nr; - struct mtd_info *mtd; - u32 peripid2 = readl(&fsmc_regs_p->peripid2); - - fsmc_version = (peripid2 >> FSMC_REVISION_SHFT) & - FSMC_REVISION_MSK; - - writel(readl(&fsmc_regs_p->ctrl) | FSMC_WP, &fsmc_regs_p->ctrl); - -#if defined(CONFIG_SYS_FSMC_NAND_16BIT) - writel(FSMC_DEVWID_16 | FSMC_DEVTYPE_NAND | FSMC_ENABLE | FSMC_WAITON, - &fsmc_regs_p->pc); -#elif defined(CONFIG_SYS_FSMC_NAND_8BIT) - writel(FSMC_DEVWID_8 | FSMC_DEVTYPE_NAND | FSMC_ENABLE | FSMC_WAITON, - &fsmc_regs_p->pc); -#else -#error Please define CONFIG_SYS_FSMC_NAND_16BIT or CONFIG_SYS_FSMC_NAND_8BIT -#endif - writel(readl(&fsmc_regs_p->pc) | FSMC_TCLR_1 | FSMC_TAR_1, - &fsmc_regs_p->pc); - writel(FSMC_THIZ_1 | FSMC_THOLD_4 | FSMC_TWAIT_6 | FSMC_TSET_0, - &fsmc_regs_p->comm); - writel(FSMC_THIZ_1 | FSMC_THOLD_4 | FSMC_TWAIT_6 | FSMC_TSET_0, - &fsmc_regs_p->attrib); - - nand->options = 0; -#if defined(CONFIG_SYS_FSMC_NAND_16BIT) - nand->options |= NAND_BUSWIDTH_16; -#endif - nand->ecc.mode = NAND_ECC_HW; - nand->ecc.size = 512; - nand->ecc.calculate = fsmc_read_hwecc; - nand->ecc.hwctl = fsmc_enable_hwecc; - nand->cmd_ctrl = fsmc_nand_hwcontrol; - nand->IO_ADDR_R = nand->IO_ADDR_W = - (void __iomem *)CFG_SYS_NAND_BASE; - nand->badblockbits = 7; - - mtd = nand_to_mtd(nand); - - switch (fsmc_version) { - case FSMC_VER8: - nand->ecc.bytes = 13; - nand->ecc.strength = 8; - nand->ecc.correct = fsmc_bch8_correct_data; - nand->ecc.read_page = fsmc_read_page_hwecc; - if (mtd->writesize == 512) - nand->ecc.layout = &fsmc_ecc4_sp_layout; - else { - if (mtd->oobsize == 224) - nand->ecc.layout = &fsmc_ecc4_224_layout; - else - nand->ecc.layout = &fsmc_ecc4_lp_layout; - } - - break; - default: - nand->ecc.bytes = 3; - nand->ecc.strength = 1; - nand->ecc.layout = &fsmc_ecc1_layout; - nand->ecc.correct = nand_correct_data; - break; - } - - /* Detect NAND chips */ - if (nand_scan_ident(mtd, CONFIG_SYS_MAX_NAND_DEVICE, NULL)) - return -ENXIO; - - if (nand_scan_tail(mtd)) - return -ENXIO; - - if (nand_register(chip_nr++, mtd)) - return -ENXIO; - - return 0; -} diff --git a/include/linux/mtd/fsmc_nand.h b/include/linux/mtd/fsmc_nand.h deleted file mode 100644 index 1d8a067f17e..00000000000 --- a/include/linux/mtd/fsmc_nand.h +++ /dev/null @@ -1,84 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2010 - * Vipin Kumar, STMicroelectronics, vipin.kumar@st.com. - */ - -#ifndef __FSMC_NAND_H__ -#define __FSMC_NAND_H__ - -#include <linux/mtd/rawnand.h> - -struct fsmc_regs { - u32 ctrl; /* 0x00 */ - u8 reserved_1[0x40 - 0x04]; - u32 pc; /* 0x40 */ - u32 sts; /* 0x44 */ - u32 comm; /* 0x48 */ - u32 attrib; /* 0x4c */ - u32 ioata; /* 0x50 */ - u32 ecc1; /* 0x54 */ - u32 ecc2; /* 0x58 */ - u32 ecc3; /* 0x5c */ - u8 reserved_2[0xfe0 - 0x60]; - u32 peripid0; /* 0xfe0 */ - u32 peripid1; /* 0xfe4 */ - u32 peripid2; /* 0xfe8 */ - u32 peripid3; /* 0xfec */ - u32 pcellid0; /* 0xff0 */ - u32 pcellid1; /* 0xff4 */ - u32 pcellid2; /* 0xff8 */ - u32 pcellid3; /* 0xffc */ -}; - -/* ctrl register definitions */ -#define FSMC_WP (1 << 7) - -/* pc register definitions */ -#define FSMC_RESET (1 << 0) -#define FSMC_WAITON (1 << 1) -#define FSMC_ENABLE (1 << 2) -#define FSMC_DEVTYPE_NAND (1 << 3) -#define FSMC_DEVWID_8 (0 << 4) -#define FSMC_DEVWID_16 (1 << 4) -#define FSMC_ECCEN (1 << 6) -#define FSMC_ECCPLEN_512 (0 << 7) -#define FSMC_ECCPLEN_256 (1 << 7) -#define FSMC_TCLR_1 (1 << 9) -#define FSMC_TAR_1 (1 << 13) - -/* sts register definitions */ -#define FSMC_CODE_RDY (1 << 15) - -/* comm register definitions */ -#define FSMC_TSET_0 (0 << 0) -#define FSMC_TWAIT_6 (6 << 8) -#define FSMC_THOLD_4 (4 << 16) -#define FSMC_THIZ_1 (1 << 24) - -/* peripid2 register definitions */ -#define FSMC_REVISION_MSK (0xf) -#define FSMC_REVISION_SHFT (0x4) - -#define FSMC_VER8 0x8 - -/* - * There are 13 bytes of ecc for every 512 byte block and it has to be read - * consecutively and immediately after the 512 byte data block for hardware to - * generate the error bit offsets - * Managing the ecc bytes in the following way is easier. This way is similar to - * oobfree structure maintained already in u-boot nand driver - */ -#define FSMC_MAX_ECCPLACE_ENTRIES 32 - -struct fsmc_nand_eccplace { - u32 offset; - u32 length; -}; - -struct fsmc_eccplace { - struct fsmc_nand_eccplace eccplace[FSMC_MAX_ECCPLACE_ENTRIES]; -}; - -extern int fsmc_nand_init(struct nand_chip *nand); -#endif -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 40/76] mtd: Drop unused nand_plat driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (37 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 38/76] mtd: Drop unused fsmc_nand driver Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 41/76] Makefile: Drop CONFIG_OF_EARLY_FLATTREE Simon Glass ` (33 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used since this commit: 936478e797a SPARC: Remove Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/mtd/nand/raw/Makefile | 1 - drivers/mtd/nand/raw/nand_plat.c | 65 -------------------------------- 2 files changed, 66 deletions(-) delete mode 100644 drivers/mtd/nand/raw/nand_plat.c diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile index c25acb11804..add2b4cf655 100644 --- a/drivers/mtd/nand/raw/Makefile +++ b/drivers/mtd/nand/raw/Makefile @@ -70,7 +70,6 @@ obj-$(CONFIG_NAND_PXA3XX) += pxa3xx_nand.o obj-$(CONFIG_TEGRA_NAND) += tegra_nand.o obj-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o obj-$(CONFIG_NAND_OMAP_ELM) += omap_elm.o -obj-$(CONFIG_NAND_PLAT) += nand_plat.o obj-$(CONFIG_NAND_SUNXI) += sunxi_nand.o obj-$(CONFIG_NAND_MXIC) += mxic_nand.o obj-$(CONFIG_NAND_ZYNQ) += zynq_nand.o diff --git a/drivers/mtd/nand/raw/nand_plat.c b/drivers/mtd/nand/raw/nand_plat.c deleted file mode 100644 index 81e7aa218d5..00000000000 --- a/drivers/mtd/nand/raw/nand_plat.c +++ /dev/null @@ -1,65 +0,0 @@ -/* - * Genericish driver for memory mapped NAND devices - * - * Copyright (c) 2006-2009 Analog Devices Inc. - * Licensed under the GPL-2 or later. - */ - -/* Your board must implement the following macros: - * NAND_PLAT_WRITE_CMD(chip, cmd) - * NAND_PLAT_WRITE_ADR(chip, cmd) - * NAND_PLAT_INIT() - * - * It may also implement the following: - * NAND_PLAT_DEV_READY(chip) - */ - -#include <common.h> -#include <linux/mtd/rawnand.h> -#include <asm/io.h> -#ifdef NAND_PLAT_GPIO_DEV_READY -# include <asm/gpio.h> -# define NAND_PLAT_DEV_READY(chip) gpio_get_value(NAND_PLAT_GPIO_DEV_READY) -#endif - -#include <nand.h> - -static void plat_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) -{ - struct nand_chip *this = mtd_to_nand(mtd); - - if (cmd == NAND_CMD_NONE) - return; - - if (ctrl & NAND_CLE) - NAND_PLAT_WRITE_CMD(this, cmd); - else - NAND_PLAT_WRITE_ADR(this, cmd); -} - -#ifdef NAND_PLAT_DEV_READY -static int plat_dev_ready(struct mtd_info *mtd) -{ - return NAND_PLAT_DEV_READY((struct nand_chip *)mtd_to_nand(mtd)); -} -#else -# define plat_dev_ready NULL -#endif - -int board_nand_init(struct nand_chip *nand) -{ -#ifdef NAND_PLAT_GPIO_DEV_READY - gpio_request(NAND_PLAT_GPIO_DEV_READY, "nand-plat"); - gpio_direction_input(NAND_PLAT_GPIO_DEV_READY); -#endif - -#ifdef NAND_PLAT_INIT - NAND_PLAT_INIT(); -#endif - - nand->cmd_ctrl = plat_cmd_ctrl; - nand->dev_ready = plat_dev_ready; - nand->ecc.mode = NAND_ECC_SOFT; - - return 0; -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 41/76] Makefile: Drop CONFIG_OF_EARLY_FLATTREE 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (38 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 40/76] mtd: Drop unused nand_plat driver Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 42/76] omap: Drop unused CONFIG_OMAP_USB_PHY Simon Glass ` (32 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This option does not exist, so drop the dead code. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) Makefile | 4 ---- 1 file changed, 4 deletions(-) diff --git a/Makefile b/Makefile index 2648fd5d8f9..5ef572e5177 100644 --- a/Makefile +++ b/Makefile @@ -2004,10 +2004,6 @@ dtbs: prepare3 scripts_dtc dtbs_install: $(Q)$(MAKE) $(dtbinst)=$(dtstree) -ifdef CONFIG_OF_EARLY_FLATTREE -all: dtbs -endif - endif # Check dtc and pylibfdt, if DTC is provided, else build them -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 42/76] omap: Drop unused CONFIG_OMAP_USB_PHY 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (39 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 41/76] Makefile: Drop CONFIG_OF_EARLY_FLATTREE Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 44/76] ppc: Drop unused CONFIG_P2020DS Simon Glass ` (31 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This option does not exist, so the Makefile rule does nothing. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> --- (no changes since v1) drivers/Makefile | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/Makefile b/drivers/Makefile index 83b14ef1fd3..15d19d0c8a3 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -59,7 +59,6 @@ obj-$(CONFIG_SPL_USB_GADGET) += usb/common/ obj-$(CONFIG_SPL_USB_GADGET) += usb/gadget/udc/ obj-$(CONFIG_SPL_WATCHDOG) += watchdog/ obj-$(CONFIG_SPL_USB_HOST) += usb/host/ -obj-$(CONFIG_OMAP_USB_PHY) += usb/phy/ obj-$(CONFIG_SPL_SATA) += ata/ scsi/ obj-$(CONFIG_SPL_LEGACY_BLOCK) += block/ obj-$(CONFIG_SPL_THERMAL) += thermal/ -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 44/76] ppc: Drop unused CONFIG_P2020DS 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (40 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 42/76] omap: Drop unused CONFIG_OMAP_USB_PHY Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 45/76] gpio: Drop unused pca9698 driver Simon Glass ` (30 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot Cc: Tom Rini, Simon Glass, Andy Fleming, Mario Six, Priyanka Jain, Stefan Roese, Wolfgang Denk This option does not exist, so the Makefile rule does nothing. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) board/freescale/common/Makefile | 1 - 1 file changed, 1 deletion(-) diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index fc51d6d3e18..9d5f38bb225 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -54,7 +54,6 @@ obj-$(CONFIG_TARGET_MPC8548CDS) += cds_pci_ft.o obj-$(CONFIG_TARGET_MPC8536DS) += ics307_clk.o obj-$(CONFIG_TARGET_P1022DS) += ics307_clk.o -obj-$(CONFIG_P2020DS) += ics307_clk.o obj-$(CONFIG_TARGET_P3041DS) += ics307_clk.o obj-$(CONFIG_TARGET_P4080DS) += ics307_clk.o obj-$(CONFIG_TARGET_P5040DS) += ics307_clk.o -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 45/76] gpio: Drop unused pca9698 driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (41 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 44/76] ppc: Drop unused CONFIG_P2020DS Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 46/76] samsung: Rename PINCTRL_EXYNOS78x0 Simon Glass ` (29 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used. Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/mips/mach-octeon/octeon_fdt.c | 43 +--------- board/gdsys/a38x/hre.c | 1 - drivers/gpio/Makefile | 1 - drivers/gpio/pca9698.c | 127 ----------------------------- include/pca9698.h | 17 ---- 5 files changed, 1 insertion(+), 188 deletions(-) delete mode 100644 drivers/gpio/pca9698.c delete mode 100644 include/pca9698.h diff --git a/arch/mips/mach-octeon/octeon_fdt.c b/arch/mips/mach-octeon/octeon_fdt.c index 0ccfe149dcc..c74fe9d9fb8 100644 --- a/arch/mips/mach-octeon/octeon_fdt.c +++ b/arch/mips/mach-octeon/octeon_fdt.c @@ -30,9 +30,6 @@ #ifdef CONFIG_PCF857X #include <pcf857x.h> #endif -#ifdef CONFIG_PCA9698 -#include <pca9698.h> -#endif #ifdef CONFIG_PCA9554 #include <pca9554.h> #endif @@ -59,13 +56,6 @@ static const char * const pca9555_gpio_list[] = { }; #endif -#ifdef CONFIG_PCA9698 -/** List of compatible strings supported by pca9698 driver */ -static const char * const pca9698_gpio_list[] = { - "nxp,pca9505", "pca9505", "nxp,pca9698", "pca9698", NULL, -}; -#endif - #ifdef CONFIG_PCA953X /** List of compatible strings supported by pca953x driver */ static const char * const pca953x_gpio_list[] = { @@ -807,19 +797,6 @@ int octeon_fdt_read_gpio(const void *fdt, int phandle, int pin) } value = (value >> pin) & 1; break; -#endif -#ifdef CONFIG_PCA9698 - case CVMX_GPIO_PIN_PCA9698: - node = fdt_node_offset_by_phandle(fdt, phandle); - if (octeon_fdt_get_i2c_bus_addr(fdt, node, &bus, &addr)) { - printf("%s: Could not get gpio bus and/or address\n", __func__); - return -1; - } - old_bus = i2c_get_bus_num(); - i2c_set_bus_num(bus); - value = pca9698_get_value(addr, pin); - i2c_set_bus_num(old_bus); - break; #endif case CVMX_GPIO_PIN_OCTEON: value = gpio_get_value(pin); @@ -880,18 +857,6 @@ int octeon_fdt_set_gpio(const void *fdt, int phandle, int pin, int val) return -1; } return pcf957x_set_val(bus, addr, 1 << pin, val << pin); -#endif -#ifdef CONFIG_PCA9698 - case CVMX_GPIO_PIN_PCA9698: - if (octeon_fdt_get_i2c_bus_addr(fdt, node, &bus, &addr)) { - printf("%s: Could not get gpio bus and/or address\n", __func__); - return -1; - } - old_bus = i2c_get_bus_num(); - i2c_set_bus_num(bus); - rc = pca9698_set_value(addr, pin, val); - i2c_set_bus_num(old_bus); - return rc; #endif case CVMX_GPIO_PIN_OCTEON: return gpio_set_value(pin, val); @@ -951,13 +916,7 @@ int octeon_fdt_get_gpio_info(int fdt_node, enum octeon_gpio_type *type, *type = GPIO_TYPE_PCA953X; } #endif -#ifdef CONFIG_PCA9698 - if (!octeon_fdt_node_check_compatible(fdt, fdt_node, pca9698_gpio_list)) { - debug("%s: Found PCA9698 compatible GPIO", __func__); - *type = GPIO_TYPE_PCA9698; - } -#endif -#if defined(CONFIG_PCA953X) || defined(CONFIG_PCA9698) || \ +#if defined(CONFIG_PCA953X) || \ defined(CONFIG_PCA9555) || defined(CONFIG_PCA9554) if (!i2c_addr || !i2c_bus) { printf("%s: Error: i2c_addr or i2c_bus is NULL\n", __func__); diff --git a/board/gdsys/a38x/hre.c b/board/gdsys/a38x/hre.c index 2f16a4d3e11..d16233ed78e 100644 --- a/board/gdsys/a38x/hre.c +++ b/board/gdsys/a38x/hre.c @@ -15,7 +15,6 @@ #include <u-boot/sha1.h> #include <asm/byteorder.h> #include <asm/unaligned.h> -#include <pca9698.h> #include "hre.h" diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 889a88dc885..fcd136367ac 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -28,7 +28,6 @@ obj-$(CONFIG_MXC_GPIO) += mxc_gpio.o obj-$(CONFIG_MXS_GPIO) += mxs_gpio.o obj-$(CONFIG_NPCM_GPIO) += npcm_gpio.o obj-$(CONFIG_PCA953X) += pca953x.o -obj-$(CONFIG_PCA9698) += pca9698.o obj-$(CONFIG_ROCKCHIP_GPIO) += rk_gpio.o obj-$(CONFIG_RCAR_GPIO) += gpio-rcar.o obj-$(CONFIG_RZA1_GPIO) += gpio-rza1.o diff --git a/drivers/gpio/pca9698.c b/drivers/gpio/pca9698.c deleted file mode 100644 index 11274c78101..00000000000 --- a/drivers/gpio/pca9698.c +++ /dev/null @@ -1,127 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2011 - * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc - */ - -/* - * Driver for NXP's pca9698 40 bit I2C gpio expander - */ - -#include <common.h> -#include <i2c.h> -#include <malloc.h> -#include <linux/errno.h> -#include <pca9698.h> - -/* - * The pca9698 registers - */ - -#define PCA9698_REG_INPUT 0x00 -#define PCA9698_REG_OUTPUT 0x08 -#define PCA9698_REG_POLARITY 0x10 -#define PCA9698_REG_CONFIG 0x18 - -#define PCA9698_BUFFER_SIZE 5 -#define PCA9698_GPIO_COUNT 40 - -static int pca9698_read40(u8 addr, u8 offset, u8 *buffer) -{ - u8 command = offset | 0x80; /* autoincrement */ - - return i2c_read(addr, command, 1, buffer, PCA9698_BUFFER_SIZE); -} - -static int pca9698_write40(u8 addr, u8 offset, u8 *buffer) -{ - u8 command = offset | 0x80; /* autoincrement */ - - return i2c_write(addr, command, 1, buffer, PCA9698_BUFFER_SIZE); -} - -static void pca9698_set_bit(unsigned gpio, u8 *buffer, unsigned value) -{ - unsigned byte = gpio / 8; - unsigned bit = gpio % 8; - - if (value) - buffer[byte] |= (1 << bit); - else - buffer[byte] &= ~(1 << bit); -} - -int pca9698_request(unsigned gpio, const char *label) -{ - if (gpio >= PCA9698_GPIO_COUNT) - return -EINVAL; - - return 0; -} - -void pca9698_free(unsigned gpio) -{ -} - -int pca9698_direction_input(u8 addr, unsigned gpio) -{ - u8 data[PCA9698_BUFFER_SIZE]; - int res; - - res = pca9698_read40(addr, PCA9698_REG_CONFIG, data); - if (res) - return res; - - pca9698_set_bit(gpio, data, 1); - - return pca9698_write40(addr, PCA9698_REG_CONFIG, data); -} - -int pca9698_direction_output(u8 addr, unsigned gpio, int value) -{ - u8 data[PCA9698_BUFFER_SIZE]; - int res; - - res = pca9698_set_value(addr, gpio, value); - if (res) - return res; - - res = pca9698_read40(addr, PCA9698_REG_CONFIG, data); - if (res) - return res; - - pca9698_set_bit(gpio, data, 0); - - return pca9698_write40(addr, PCA9698_REG_CONFIG, data); -} - -int pca9698_get_value(u8 addr, unsigned gpio) -{ - unsigned config_byte = gpio / 8; - unsigned config_bit = gpio % 8; - unsigned value; - u8 data[PCA9698_BUFFER_SIZE]; - int res; - - res = pca9698_read40(addr, PCA9698_REG_INPUT, data); - if (res) - return -1; - - value = data[config_byte] & (1 << config_bit); - - return !!value; -} - -int pca9698_set_value(u8 addr, unsigned gpio, int value) -{ - u8 data[PCA9698_BUFFER_SIZE]; - int res; - - res = pca9698_read40(addr, PCA9698_REG_OUTPUT, data); - if (res) - return res; - - pca9698_set_bit(gpio, data, value); - - return pca9698_write40(addr, PCA9698_REG_OUTPUT, data); -} diff --git a/include/pca9698.h b/include/pca9698.h deleted file mode 100644 index 48a5f756e28..00000000000 --- a/include/pca9698.h +++ /dev/null @@ -1,17 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2011 - * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc - */ - -#ifndef __PCA9698_H_ -#define __PCA9698_H_ - -int pca9698_request(unsigned gpio, const char *label); -void pca9698_free(unsigned gpio); -int pca9698_direction_input(u8 addr, unsigned gpio); -int pca9698_direction_output(u8 addr, unsigned gpio, int value); -int pca9698_get_value(u8 addr, unsigned gpio); -int pca9698_set_value(u8 addr, unsigned gpio, int value); - -#endif /* __PCA9698_H_ */ -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 46/76] samsung: Rename PINCTRL_EXYNOS78x0 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (42 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 45/76] gpio: Drop unused pca9698 driver Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-03 6:04 ` Minkyu Kang 2023-02-01 20:19 ` [PATCH v3 47/76] power: Drop unused bat_trats driver and battery code Simon Glass ` (28 subsequent siblings) 72 siblings, 1 reply; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Minkyu Kang CONFIG options must not use lower-case letter. Convert this to upper case. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/arm/mach-exynos/Kconfig | 6 +++--- drivers/pinctrl/exynos/Kconfig | 2 +- drivers/pinctrl/exynos/Makefile | 2 +- 3 files changed, 5 insertions(+), 5 deletions(-) diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index 8f3aee052c8..1a1fd7261b1 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -204,7 +204,7 @@ config TARGET_A5Y17LTE select CLK_EXYNOS select OF_CONTROL select PINCTRL - select PINCTRL_EXYNOS78x0 + select PINCTRL_EXYNOS78X0 select SUPPORT_SPL config TARGET_A7Y17LTE @@ -213,7 +213,7 @@ config TARGET_A7Y17LTE select CLK_EXYNOS select OF_CONTROL select PINCTRL - select PINCTRL_EXYNOS78x0 + select PINCTRL_EXYNOS78X0 select SUPPORT_SPL config TARGET_A3Y17LTE @@ -222,7 +222,7 @@ config TARGET_A3Y17LTE select CLK_EXYNOS select OF_CONTROL select PINCTRL - select PINCTRL_EXYNOS78x0 + select PINCTRL_EXYNOS78X0 select SUPPORT_SPL endchoice diff --git a/drivers/pinctrl/exynos/Kconfig b/drivers/pinctrl/exynos/Kconfig index a60f49869b4..821bdd14072 100644 --- a/drivers/pinctrl/exynos/Kconfig +++ b/drivers/pinctrl/exynos/Kconfig @@ -9,7 +9,7 @@ config PINCTRL_EXYNOS7420 Support pin multiplexing and pin configuration control on Samsung's Exynos7420 SoC. -config PINCTRL_EXYNOS78x0 +config PINCTRL_EXYNOS78X0 bool "Samsung Exynos78x0 pinctrl driver" depends on ARCH_EXYNOS && PINCTRL_FULL select PINCTRL_EXYNOS diff --git a/drivers/pinctrl/exynos/Makefile b/drivers/pinctrl/exynos/Makefile index 07db970ca94..445c8e17aea 100644 --- a/drivers/pinctrl/exynos/Makefile +++ b/drivers/pinctrl/exynos/Makefile @@ -5,4 +5,4 @@ obj-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o obj-$(CONFIG_PINCTRL_EXYNOS7420) += pinctrl-exynos7420.o -obj-$(CONFIG_PINCTRL_EXYNOS78x0) += pinctrl-exynos78x0.o +obj-$(CONFIG_PINCTRL_EXYNOS78X0) += pinctrl-exynos78x0.o -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* Re: [PATCH v3 46/76] samsung: Rename PINCTRL_EXYNOS78x0 2023-02-01 20:19 ` [PATCH v3 46/76] samsung: Rename PINCTRL_EXYNOS78x0 Simon Glass @ 2023-02-03 6:04 ` Minkyu Kang 0 siblings, 0 replies; 87+ messages in thread From: Minkyu Kang @ 2023-02-03 6:04 UTC (permalink / raw) To: Simon Glass; +Cc: u-boot, Tom Rini, Minkyu Kang Hi, On Thu, 2 Feb 2023 at 05:48, Simon Glass <sjg@chromium.org> wrote: > CONFIG options must not use lower-case letter. Convert this to upper case. > > Signed-off-by: Simon Glass <sjg@chromium.org> > --- > > (no changes since v1) > > arch/arm/mach-exynos/Kconfig | 6 +++--- > drivers/pinctrl/exynos/Kconfig | 2 +- > drivers/pinctrl/exynos/Makefile | 2 +- > 3 files changed, 5 insertions(+), 5 deletions(-) > > diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig > index 8f3aee052c8..1a1fd7261b1 100644 > --- a/arch/arm/mach-exynos/Kconfig > +++ b/arch/arm/mach-exynos/Kconfig > @@ -204,7 +204,7 @@ config TARGET_A5Y17LTE > select CLK_EXYNOS > select OF_CONTROL > select PINCTRL > - select PINCTRL_EXYNOS78x0 > + select PINCTRL_EXYNOS78X0 > select SUPPORT_SPL > > config TARGET_A7Y17LTE > @@ -213,7 +213,7 @@ config TARGET_A7Y17LTE > select CLK_EXYNOS > select OF_CONTROL > select PINCTRL > - select PINCTRL_EXYNOS78x0 > + select PINCTRL_EXYNOS78X0 > select SUPPORT_SPL > > config TARGET_A3Y17LTE > @@ -222,7 +222,7 @@ config TARGET_A3Y17LTE > select CLK_EXYNOS > select OF_CONTROL > select PINCTRL > - select PINCTRL_EXYNOS78x0 > + select PINCTRL_EXYNOS78X0 > select SUPPORT_SPL > > endchoice > diff --git a/drivers/pinctrl/exynos/Kconfig > b/drivers/pinctrl/exynos/Kconfig > index a60f49869b4..821bdd14072 100644 > --- a/drivers/pinctrl/exynos/Kconfig > +++ b/drivers/pinctrl/exynos/Kconfig > @@ -9,7 +9,7 @@ config PINCTRL_EXYNOS7420 > Support pin multiplexing and pin configuration control on > Samsung's Exynos7420 SoC. > > -config PINCTRL_EXYNOS78x0 > +config PINCTRL_EXYNOS78X0 > bool "Samsung Exynos78x0 pinctrl driver" > depends on ARCH_EXYNOS && PINCTRL_FULL > select PINCTRL_EXYNOS > diff --git a/drivers/pinctrl/exynos/Makefile > b/drivers/pinctrl/exynos/Makefile > index 07db970ca94..445c8e17aea 100644 > --- a/drivers/pinctrl/exynos/Makefile > +++ b/drivers/pinctrl/exynos/Makefile > @@ -5,4 +5,4 @@ > > obj-$(CONFIG_PINCTRL_EXYNOS) += pinctrl-exynos.o > obj-$(CONFIG_PINCTRL_EXYNOS7420) += pinctrl-exynos7420.o > -obj-$(CONFIG_PINCTRL_EXYNOS78x0) += pinctrl-exynos78x0.o > +obj-$(CONFIG_PINCTRL_EXYNOS78X0) += pinctrl-exynos78x0.o > -- > 2.39.1.456.gfc5497dd1b-goog > > Reviewed-by: Minkyu Kang <mk7.kang@samsung.com> -- Thanks, Minkyu Kang. ^ permalink raw reply [flat|nested] 87+ messages in thread
* [PATCH v3 47/76] power: Drop unused bat_trats driver and battery code 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (43 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 46/76] samsung: Rename PINCTRL_EXYNOS78x0 Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 48/76] power: Drop unused fg_max17042 driver and fuel gauge code Simon Glass ` (27 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This driver and bat_trats2 are not used. Drop them and the entire battery directory, since there is nothing left. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/power/Makefile | 1 - drivers/power/battery/Makefile | 7 --- drivers/power/battery/bat_trats.c | 91 ------------------------------ drivers/power/battery/bat_trats2.c | 65 --------------------- 4 files changed, 164 deletions(-) delete mode 100644 drivers/power/battery/Makefile delete mode 100644 drivers/power/battery/bat_trats.c delete mode 100644 drivers/power/battery/bat_trats2.c diff --git a/drivers/power/Makefile b/drivers/power/Makefile index 34a84808a9c..efdae3655ac 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -4,7 +4,6 @@ # Tom Rix <Tom.Rix at windriver.com> obj-$(CONFIG_$(SPL_TPL_)ACPI_PMC) += acpi_pmc/ -obj-y += battery/ obj-$(CONFIG_$(SPL_TPL_)POWER_DOMAIN) += domain/ obj-y += fuel_gauge/ obj-y += mfd/ diff --git a/drivers/power/battery/Makefile b/drivers/power/battery/Makefile deleted file mode 100644 index 370923a6ed9..00000000000 --- a/drivers/power/battery/Makefile +++ /dev/null @@ -1,7 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# Copyright (C) 2012 Samsung Electronics -# Lukasz Majewski <l.majewski@samsung.com> - -obj-$(CONFIG_POWER_BATTERY_TRATS) += bat_trats.o -obj-$(CONFIG_POWER_BATTERY_TRATS2) += bat_trats2.o diff --git a/drivers/power/battery/bat_trats.c b/drivers/power/battery/bat_trats.c deleted file mode 100644 index 54b2bf91e5c..00000000000 --- a/drivers/power/battery/bat_trats.c +++ /dev/null @@ -1,91 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2012 Samsung Electronics - * Lukasz Majewski <l.majewski@samsung.com> - */ - -#include <common.h> -#include <console.h> -#include <log.h> -#include <linux/delay.h> -#include <power/pmic.h> -#include <power/battery.h> -#include <power/max8997_pmic.h> -#include <errno.h> - -static struct battery battery_trats; - -static int power_battery_charge(struct pmic *bat) -{ - struct power_battery *p_bat = bat->pbat; - struct battery *battery = p_bat->bat; - int k; - - if (bat->chrg->chrg_state(p_bat->chrg, PMIC_CHARGER_ENABLE, 450)) - return -1; - - for (k = 0; bat->chrg->chrg_bat_present(p_bat->chrg) && - bat->chrg->chrg_type(p_bat->muic) && - battery->state_of_chrg < 100; k++) { - udelay(2000000); - if (!(k % 5)) - puts("."); - bat->fg->fg_battery_update(p_bat->fg, bat); - - if (k == 200) { - debug(" %d [V]", battery->voltage_uV); - puts("\n"); - k = 0; - } - - if (ctrlc()) { - printf("\nCharging disabled on request.\n"); - goto exit; - } - } - exit: - bat->chrg->chrg_state(p_bat->chrg, PMIC_CHARGER_DISABLE, 0); - - return 0; -} - -static int power_battery_init_trats(struct pmic *bat_, - struct pmic *fg_, - struct pmic *chrg_, - struct pmic *muic_) -{ - bat_->pbat->fg = fg_; - bat_->pbat->chrg = chrg_; - bat_->pbat->muic = muic_; - - bat_->fg = fg_->fg; - bat_->chrg = chrg_->chrg; - bat_->chrg->chrg_type = muic_->chrg->chrg_type; - return 0; -} - -static struct power_battery power_bat_trats = { - .bat = &battery_trats, - .battery_init = power_battery_init_trats, - .battery_charge = power_battery_charge, -}; - -int power_bat_init(unsigned char bus) -{ - static const char name[] = "BAT_TRATS"; - struct pmic *p = pmic_alloc(); - - if (!p) { - printf("%s: POWER allocation error!\n", __func__); - return -ENOMEM; - } - - debug("Board BAT init\n"); - - p->interface = PMIC_NONE; - p->name = name; - p->bus = bus; - - p->pbat = &power_bat_trats; - return 0; -} diff --git a/drivers/power/battery/bat_trats2.c b/drivers/power/battery/bat_trats2.c deleted file mode 100644 index 1172970d1e0..00000000000 --- a/drivers/power/battery/bat_trats2.c +++ /dev/null @@ -1,65 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2013 Samsung Electronics - * Piotr Wilczek <p.wilczek@samsung.com> - */ - -#include <common.h> -#include <log.h> -#include <power/pmic.h> -#include <power/battery.h> -#include <power/max77693_pmic.h> -#include <errno.h> - -static struct battery battery_trats; - -static int power_battery_charge(struct pmic *bat) -{ - struct power_battery *p_bat = bat->pbat; - - if (bat->chrg->chrg_state(p_bat->chrg, PMIC_CHARGER_ENABLE, 450)) - return -EINVAL; - - return 0; -} - -static int power_battery_init_trats2(struct pmic *bat_, - struct pmic *fg_, - struct pmic *chrg_, - struct pmic *muic_) -{ - bat_->pbat->fg = fg_; - bat_->pbat->chrg = chrg_; - bat_->pbat->muic = muic_; - - bat_->fg = fg_->fg; - bat_->chrg = chrg_->chrg; - bat_->chrg->chrg_type = muic_->chrg->chrg_type; - return 0; -} - -static struct power_battery power_bat_trats2 = { - .bat = &battery_trats, - .battery_init = power_battery_init_trats2, - .battery_charge = power_battery_charge, -}; - -int power_bat_init(unsigned char bus) -{ - static const char name[] = "BAT_TRATS2"; - struct pmic *p = pmic_alloc(); - - if (!p) { - printf("%s: POWER allocation error!\n", __func__); - return -ENOMEM; - } - - debug("Board BAT init\n"); - - p->interface = PMIC_NONE; - p->name = name; - p->bus = bus; - - p->pbat = &power_bat_trats2; - return 0; -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 48/76] power: Drop unused fg_max17042 driver and fuel gauge code 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (44 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 47/76] power: Drop unused bat_trats driver and battery code Simon Glass @ 2023-02-01 20:19 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 49/76] power: Drop unused muic_max77693 driver and mfd code Simon Glass ` (26 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:19 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This driver is not used. Drop it and the entire fuel_gauge directory, since there is nothing left. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/power/Makefile | 1 - drivers/power/fuel_gauge/Makefile | 6 - drivers/power/fuel_gauge/fg_max17042.c | 287 ------------------------- include/power/fg_battery_cell_params.h | 73 ------- 4 files changed, 367 deletions(-) delete mode 100644 drivers/power/fuel_gauge/Makefile delete mode 100644 drivers/power/fuel_gauge/fg_max17042.c delete mode 100644 include/power/fg_battery_cell_params.h diff --git a/drivers/power/Makefile b/drivers/power/Makefile index efdae3655ac..93003e97e01 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -5,7 +5,6 @@ obj-$(CONFIG_$(SPL_TPL_)ACPI_PMC) += acpi_pmc/ obj-$(CONFIG_$(SPL_TPL_)POWER_DOMAIN) += domain/ -obj-y += fuel_gauge/ obj-y += mfd/ obj-y += pmic/ obj-y += regulator/ diff --git a/drivers/power/fuel_gauge/Makefile b/drivers/power/fuel_gauge/Makefile deleted file mode 100644 index ca2df947585..00000000000 --- a/drivers/power/fuel_gauge/Makefile +++ /dev/null @@ -1,6 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# Copyright (C) 2012 Samsung Electronics -# Lukasz Majewski <l.majewski@samsung.com> - -obj-$(CONFIG_POWER_FG_MAX17042) += fg_max17042.o diff --git a/drivers/power/fuel_gauge/fg_max17042.c b/drivers/power/fuel_gauge/fg_max17042.c deleted file mode 100644 index a395d587a86..00000000000 --- a/drivers/power/fuel_gauge/fg_max17042.c +++ /dev/null @@ -1,287 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2012 Samsung Electronics - * Lukasz Majewski <l.majewski@samsung.com> - */ - -#include <common.h> -#include <log.h> -#include <linux/delay.h> -#include <power/pmic.h> -#include <power/max17042_fg.h> -#include <i2c.h> -#include <power/max8997_pmic.h> -#include <power/power_chrg.h> -#include <power/battery.h> -#include <power/fg_battery_cell_params.h> -#include <errno.h> - -static int fg_write_regs(struct pmic *p, u8 addr, u16 *data, int num) -{ - int ret = 0; - int i; - - for (i = 0; i < num; i++, addr++) { - ret = pmic_reg_write(p, addr, *(data + i)); - if (ret) - return ret; - } - - return 0; -} - -static int fg_read_regs(struct pmic *p, u8 addr, u16 *data, int num) -{ - unsigned int dat; - int ret = 0; - int i; - - for (i = 0; i < num; i++, addr++) { - ret = pmic_reg_read(p, addr, &dat); - if (ret) - return ret; - - *(data + i) = (u16)dat; - } - - return 0; -} - -static int fg_write_and_verify(struct pmic *p, u8 addr, u16 data) -{ - unsigned int val = data; - int ret = 0; - - ret |= pmic_reg_write(p, addr, val); - ret |= pmic_reg_read(p, addr, &val); - - if (ret) - return ret; - - if (((u16) val) == data) - return 0; - - return -1; -} - -static void por_fuelgauge_init(struct pmic *p) -{ - u16 r_data0[16], r_data1[16], r_data2[16]; - u32 rewrite_count = 5; - u32 check_count; - u32 lock_count; - u32 i = 0; - u32 val; - s32 ret = 0; - char *status_msg; - - /* Delay 500 ms */ - mdelay(500); - /* Initilize Configuration */ - pmic_reg_write(p, MAX17042_CONFIG, 0x2310); - -rewrite_model: - check_count = 5; - lock_count = 5; - - if (!rewrite_count--) { - status_msg = "init failed!"; - goto error; - } - - /* Unlock Model Access */ - pmic_reg_write(p, MAX17042_MLOCKReg1, MODEL_UNLOCK1); - pmic_reg_write(p, MAX17042_MLOCKReg2, MODEL_UNLOCK2); - - /* Write/Read/Verify the Custom Model */ - ret = fg_write_regs(p, MAX17042_MODEL1, cell_character0, - ARRAY_SIZE(cell_character0)); - if (ret) - goto rewrite_model; - - ret = fg_write_regs(p, MAX17042_MODEL2, cell_character1, - ARRAY_SIZE(cell_character1)); - if (ret) - goto rewrite_model; - - ret = fg_write_regs(p, MAX17042_MODEL3, cell_character2, - ARRAY_SIZE(cell_character2)); - if (ret) - goto rewrite_model; - -check_model: - if (!check_count--) { - if (rewrite_count) - goto rewrite_model; - else - status_msg = "check failed!"; - - goto error; - } - - ret = fg_read_regs(p, MAX17042_MODEL1, r_data0, ARRAY_SIZE(r_data0)); - if (ret) - goto check_model; - - ret = fg_read_regs(p, MAX17042_MODEL2, r_data1, ARRAY_SIZE(r_data1)); - if (ret) - goto check_model; - - ret = fg_read_regs(p, MAX17042_MODEL3, r_data2, ARRAY_SIZE(r_data2)); - if (ret) - goto check_model; - - for (i = 0; i < 16; i++) { - if ((cell_character0[i] != r_data0[i]) - || (cell_character1[i] != r_data1[i]) - || (cell_character2[i] != r_data2[i])) - goto rewrite_model; - } - -lock_model: - if (!lock_count--) { - if (rewrite_count) - goto rewrite_model; - else - status_msg = "lock failed!"; - - goto error; - } - - /* Lock model access */ - pmic_reg_write(p, MAX17042_MLOCKReg1, MODEL_LOCK1); - pmic_reg_write(p, MAX17042_MLOCKReg2, MODEL_LOCK2); - - /* Verify the model access is locked */ - ret = fg_read_regs(p, MAX17042_MODEL1, r_data0, ARRAY_SIZE(r_data0)); - if (ret) - goto lock_model; - - ret = fg_read_regs(p, MAX17042_MODEL2, r_data1, ARRAY_SIZE(r_data1)); - if (ret) - goto lock_model; - - ret = fg_read_regs(p, MAX17042_MODEL3, r_data2, ARRAY_SIZE(r_data2)); - if (ret) - goto lock_model; - - for (i = 0; i < ARRAY_SIZE(r_data0); i++) { - /* Check if model locked */ - if (r_data0[i] || r_data1[i] || r_data2[i]) - goto lock_model; - } - - /* Write Custom Parameters */ - fg_write_and_verify(p, MAX17042_RCOMP0, RCOMP0); - fg_write_and_verify(p, MAX17042_TEMPCO, TempCo); - - /* Delay at least 350mS */ - mdelay(350); - - /* Initialization Complete */ - pmic_reg_read(p, MAX17042_STATUS, &val); - /* Write and Verify Status with POR bit Cleared */ - fg_write_and_verify(p, MAX17042_STATUS, val & ~MAX17042_POR); - - /* Delay at least 350 ms */ - mdelay(350); - - status_msg = "OK!"; -error: - debug("%s: model init status: %s\n", p->name, status_msg); - return; -} - -static int power_update_battery(struct pmic *p, struct pmic *bat) -{ - struct power_battery *pb = bat->pbat; - unsigned int val; - int ret = 0; - - if (pmic_probe(p)) { - puts("Can't find max17042 fuel gauge\n"); - return -ENODEV; - } - - ret |= pmic_reg_read(p, MAX17042_VFSOC, &val); - pb->bat->state_of_chrg = (val >> 8); - - pmic_reg_read(p, MAX17042_VCELL, &val); - debug("vfsoc: 0x%x\n", val); - pb->bat->voltage_uV = ((val & 0xFFUL) >> 3) + ((val & 0xFF00) >> 3); - pb->bat->voltage_uV = (pb->bat->voltage_uV * 625); - - pmic_reg_read(p, 0x05, &val); - pb->bat->capacity = val >> 2; - - return ret; -} - -static int power_check_battery(struct pmic *p, struct pmic *bat) -{ - struct power_battery *pb = bat->pbat; - unsigned int val; - int ret = 0; - - if (pmic_probe(p)) { - puts("Can't find max17042 fuel gauge\n"); - return -ENODEV; - } - - ret |= pmic_reg_read(p, MAX17042_STATUS, &val); - debug("fg status: 0x%x\n", val); - - if (val & MAX17042_POR) - por_fuelgauge_init(p); - - ret |= pmic_reg_read(p, MAX17042_VERSION, &val); - pb->bat->version = val; - - power_update_battery(p, bat); - debug("fg ver: 0x%x\n", pb->bat->version); - printf("BAT: state_of_charge(SOC):%d%%\n", - pb->bat->state_of_chrg); - - printf(" voltage: %d.%6.6d [V] (expected to be %d [mAh])\n", - pb->bat->voltage_uV / 1000000, - pb->bat->voltage_uV % 1000000, - pb->bat->capacity); - - if (pb->bat->voltage_uV > 3850000) - pb->bat->state = EXT_SOURCE; - else if (pb->bat->voltage_uV < 3600000 || pb->bat->state_of_chrg < 5) - pb->bat->state = CHARGE; - else - pb->bat->state = NORMAL; - - return ret; -} - -static struct power_fg power_fg_ops = { - .fg_battery_check = power_check_battery, - .fg_battery_update = power_update_battery, -}; - -int power_fg_init(unsigned char bus) -{ - static const char name[] = "MAX17042_FG"; - struct pmic *p = pmic_alloc(); - - if (!p) { - printf("%s: POWER allocation error!\n", __func__); - return -ENOMEM; - } - - debug("Board Fuel Gauge init\n"); - - p->name = name; - p->interface = PMIC_I2C; - p->number_of_regs = FG_NUM_OF_REGS; - p->hw.i2c.addr = MAX17042_I2C_ADDR; - p->hw.i2c.tx_num = 2; - p->sensor_byte_order = PMIC_SENSOR_BYTE_ORDER_BIG; - p->bus = bus; - - p->fg = &power_fg_ops; - return 0; -} diff --git a/include/power/fg_battery_cell_params.h b/include/power/fg_battery_cell_params.h deleted file mode 100644 index 500c8ea7174..00000000000 --- a/include/power/fg_battery_cell_params.h +++ /dev/null @@ -1,73 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2012 Samsung Electronics - * Lukasz Majewski <l.majewski@samsung.com> - */ - -#ifndef __FG_BATTERY_CELL_PARAMS_H_ -#define __FG_BATTERY_CELL_PARAMS_H_ - -#if defined(CONFIG_POWER_FG_MAX17042) && defined(CONFIG_TARGET_TRATS) - -/* Cell characteristics - Exynos4 TRATS development board */ -/* Shall be written to addr 0x80h */ -u16 cell_character0[16] = { - 0xA2A0, - 0xB6E0, - 0xB850, - 0xBAD0, - 0xBB20, - 0xBB70, - 0xBBC0, - 0xBC20, - 0xBC80, - 0xBCE0, - 0xBD80, - 0xBE20, - 0xC090, - 0xC420, - 0xC910, - 0xD070 -}; - -/* Shall be written to addr 0x90h */ -u16 cell_character1[16] = { - 0x0090, - 0x1A50, - 0x02F0, - 0x2060, - 0x2060, - 0x2E60, - 0x26A0, - 0x2DB0, - 0x2DB0, - 0x1870, - 0x2A20, - 0x16F0, - 0x08F0, - 0x0D40, - 0x08C0, - 0x08C0 -}; - -/* Shall be written to addr 0xA0h */ -u16 cell_character2[16] = { - 0x0100, - 0x0100, - 0x0100, - 0x0100, - 0x0100, - 0x0100, - 0x0100, - 0x0100, - 0x0100, - 0x0100, - 0x0100, - 0x0100, - 0x0100, - 0x0100, - 0x0100, - 0x0100 -}; -#endif -#endif /* __FG_BATTERY_CELL_PARAMS_H_ */ -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 49/76] power: Drop unused muic_max77693 driver and mfd code 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (45 preceding siblings ...) 2023-02-01 20:19 ` [PATCH v3 48/76] power: Drop unused fg_max17042 driver and fuel gauge code Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 50/76] power: Drop unused muic_max8997 driver Simon Glass ` (25 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This driver is not used and has lain unconverted since: fc47cf9d054 arm: exynos: i2c: Convert exynos boards to use DM_I2C Drop it and the entire mfd directory, since there is nothing left. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/power/Makefile | 1 - drivers/power/mfd/Makefile | 6 --- drivers/power/mfd/muic_max77693.c | 77 ------------------------------- 3 files changed, 84 deletions(-) delete mode 100644 drivers/power/mfd/Makefile delete mode 100644 drivers/power/mfd/muic_max77693.c diff --git a/drivers/power/Makefile b/drivers/power/Makefile index 93003e97e01..ba64b2c5938 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -5,7 +5,6 @@ obj-$(CONFIG_$(SPL_TPL_)ACPI_PMC) += acpi_pmc/ obj-$(CONFIG_$(SPL_TPL_)POWER_DOMAIN) += domain/ -obj-y += mfd/ obj-y += pmic/ obj-y += regulator/ diff --git a/drivers/power/mfd/Makefile b/drivers/power/mfd/Makefile deleted file mode 100644 index b5ec8f00bb0..00000000000 --- a/drivers/power/mfd/Makefile +++ /dev/null @@ -1,6 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# Copyright (C) 2013 Samsung Electronics -# Piotr Wilczek <p.wilczek@samsung.com> - -obj-$(CONFIG_POWER_MUIC_MAX77693) += muic_max77693.o diff --git a/drivers/power/mfd/muic_max77693.c b/drivers/power/mfd/muic_max77693.c deleted file mode 100644 index 36ee44b9a2c..00000000000 --- a/drivers/power/mfd/muic_max77693.c +++ /dev/null @@ -1,77 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2013 Samsung Electronics - * Piotr Wilczek <p.wilczek@samsung.com> - */ - -#include <common.h> -#include <log.h> -#include <power/pmic.h> -#include <power/power_chrg.h> -#include <power/max77693_muic.h> -#include <i2c.h> -#include <errno.h> - -static int power_chrg_get_type(struct pmic *p) -{ - unsigned int val; - unsigned int charge_type, charger; - - /* if probe failed, return cable none */ - if (pmic_probe(p)) - return CHARGER_NO; - - pmic_reg_read(p, MAX77693_MUIC_STATUS2, &val); - - charge_type = val & MAX77693_MUIC_CHG_MASK; - - switch (charge_type) { - case MAX77693_MUIC_CHG_NO: - charger = CHARGER_NO; - break; - case MAX77693_MUIC_CHG_USB: - case MAX77693_MUIC_CHG_USB_D: - charger = CHARGER_USB; - break; - case MAX77693_MUIC_CHG_TA: - case MAX77693_MUIC_CHG_TA_1A: - charger = CHARGER_TA; - break; - case MAX77693_MUIC_CHG_TA_500: - charger = CHARGER_TA_500; - break; - default: - charger = CHARGER_UNKNOWN; - break; - } - - return charger; -} - -static struct power_chrg power_chrg_muic_ops = { - .chrg_type = power_chrg_get_type, -}; - -int power_muic_init(unsigned int bus) -{ - static const char name[] = "MAX77693_MUIC"; - struct pmic *p = pmic_alloc(); - - if (!p) { - printf("%s: POWER allocation error!\n", __func__); - return -ENOMEM; - } - - debug("Board Micro USB Interface Controller init\n"); - - p->name = name; - p->interface = PMIC_I2C; - p->number_of_regs = MUIC_NUM_OF_REGS; - p->hw.i2c.addr = MAX77693_MUIC_I2C_ADDR; - p->hw.i2c.tx_num = 1; - p->bus = bus; - - p->chrg = &power_chrg_muic_ops; - - return 0; -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 50/76] power: Drop unused muic_max8997 driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (46 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 49/76] power: Drop unused muic_max77693 driver and mfd code Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 51/76] freescale: Drop unused pq-mds-pib driver Simon Glass ` (24 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used. Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/power/pmic/Makefile | 1 - drivers/power/pmic/muic_max8997.c | 74 ------------------------------- 2 files changed, 75 deletions(-) delete mode 100644 drivers/power/pmic/muic_max8997.c diff --git a/drivers/power/pmic/Makefile b/drivers/power/pmic/Makefile index c3180c58208..0b3b3d62d0e 100644 --- a/drivers/power/pmic/Makefile +++ b/drivers/power/pmic/Makefile @@ -37,7 +37,6 @@ obj-$(CONFIG_POWER_TPS65218) += pmic_tps65218.o ifeq ($(CONFIG_$(SPL_)POWER_LEGACY),y) obj-$(CONFIG_POWER_LTC3676) += pmic_ltc3676.o -obj-$(CONFIG_POWER_MUIC_MAX8997) += muic_max8997.o obj-$(CONFIG_POWER_PCA9450) += pmic_pca9450.o obj-$(CONFIG_POWER_PFUZE100) += pmic_pfuze100.o obj-$(CONFIG_POWER_PFUZE3000) += pmic_pfuze3000.o diff --git a/drivers/power/pmic/muic_max8997.c b/drivers/power/pmic/muic_max8997.c deleted file mode 100644 index 969ce902395..00000000000 --- a/drivers/power/pmic/muic_max8997.c +++ /dev/null @@ -1,74 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2012 Samsung Electronics - * Lukasz Majewski <l.majewski@samsung.com> - */ - -#include <common.h> -#include <log.h> -#include <power/pmic.h> -#include <power/power_chrg.h> -#include <power/max8997_muic.h> -#include <i2c.h> -#include <errno.h> - -static int power_chrg_get_type(struct pmic *p) -{ - unsigned int val; - unsigned char charge_type, charger; - - if (pmic_probe(p)) - return CHARGER_NO; - - pmic_reg_read(p, MAX8997_MUIC_STATUS2, &val); - charge_type = val & MAX8997_MUIC_CHG_MASK; - - switch (charge_type) { - case MAX8997_MUIC_CHG_NO: - charger = CHARGER_NO; - break; - case MAX8997_MUIC_CHG_USB: - case MAX8997_MUIC_CHG_USB_D: - charger = CHARGER_USB; - break; - case MAX8997_MUIC_CHG_TA: - case MAX8997_MUIC_CHG_TA_1A: - charger = CHARGER_TA; - break; - case MAX8997_MUIC_CHG_TA_500: - charger = CHARGER_TA_500; - break; - default: - charger = CHARGER_UNKNOWN; - break; - } - - return charger; -} - -static struct power_chrg power_chrg_muic_ops = { - .chrg_type = power_chrg_get_type, -}; - -int power_muic_init(unsigned int bus) -{ - static const char name[] = "MAX8997_MUIC"; - struct pmic *p = pmic_alloc(); - - if (!p) { - printf("%s: POWER allocation error!\n", __func__); - return -ENOMEM; - } - - debug("Board Micro USB Interface Controller init\n"); - - p->name = name; - p->interface = PMIC_I2C; - p->number_of_regs = MUIC_NUM_OF_REGS; - p->hw.i2c.addr = MAX8997_MUIC_I2C_ADDR; - p->hw.i2c.tx_num = 1; - p->bus = bus; - - p->chrg = &power_chrg_muic_ops; - return 0; -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 51/76] freescale: Drop unused pq-mds-pib driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (47 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 50/76] power: Drop unused muic_max8997 driver Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 52/76] rmobile: Drop CONFIG_RMOBILE Simon Glass ` (23 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used. Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) board/freescale/common/Makefile | 1 - board/freescale/common/pq-mds-pib.c | 60 ----------------------------- board/freescale/common/pq-mds-pib.h | 9 ----- 3 files changed, 70 deletions(-) delete mode 100644 board/freescale/common/pq-mds-pib.c delete mode 100644 board/freescale/common/pq-mds-pib.h diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index 9d5f38bb225..bd035d60a58 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -36,7 +36,6 @@ obj-$(I2C_COMMON) += i2c_common.o obj-$(CONFIG_FSL_USE_PCA9547_MUX) += i2c_mux.o obj-$(CONFIG_$(SPL_)VID) += vid.o obj-$(CONFIG_FSL_QIXIS) += qixis.o -obj-$(CONFIG_PQ_MDS_PIB) += pq-mds-pib.o ifndef CONFIG_SPL_BUILD obj-$(CONFIG_ID_EEPROM) += sys_eeprom.o endif diff --git a/board/freescale/common/pq-mds-pib.c b/board/freescale/common/pq-mds-pib.c deleted file mode 100644 index 162c8a954f0..00000000000 --- a/board/freescale/common/pq-mds-pib.c +++ /dev/null @@ -1,60 +0,0 @@ -/* - * Copyright (C) 2007 Freescale Semiconductor, Inc. - * - * Tony Li <tony.li@freescale.com> - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation; - */ - -#include <common.h> -#include <i2c.h> -#include <asm/io.h> - -#include "pq-mds-pib.h" - -int pib_init(void) -{ - u8 val8; - u8 orig_i2c_bus; - - /* Switch temporarily to I2C bus #2 */ - orig_i2c_bus = i2c_get_bus_num(); - i2c_set_bus_num(1); - - val8 = 0; -#if defined(CONFIG_PCI) && !defined(CONFIG_PCISLAVE) - /* Assign PIB PMC slot to desired PCI bus */ - i2c_write(0x23, 0x6, 1, &val8, 1); - i2c_write(0x23, 0x7, 1, &val8, 1); - val8 = 0xff; - i2c_write(0x23, 0x2, 1, &val8, 1); - i2c_write(0x23, 0x3, 1, &val8, 1); - - val8 = 0; - i2c_write(0x26, 0x6, 1, &val8, 1); - val8 = 0x34; - i2c_write(0x26, 0x7, 1, &val8, 1); - val8 = 0xf3; /* PMC1, PMC2, PMC3 slot to PCI bus */ - i2c_write(0x26, 0x2, 1, &val8, 1); - val8 = 0xff; - i2c_write(0x26, 0x3, 1, &val8, 1); - - val8 = 0; - i2c_write(0x27, 0x6, 1, &val8, 1); - i2c_write(0x27, 0x7, 1, &val8, 1); - val8 = 0xff; - i2c_write(0x27, 0x2, 1, &val8, 1); - val8 = 0xef; - i2c_write(0x27, 0x3, 1, &val8, 1); - - eieio(); - - printf("PCI 32bit bus on PMC1 & PMC2 &PMC3\n"); -#endif - - /* Reset to original I2C bus */ - i2c_set_bus_num(orig_i2c_bus); - return 0; -} diff --git a/board/freescale/common/pq-mds-pib.h b/board/freescale/common/pq-mds-pib.h deleted file mode 100644 index 67066fd118d..00000000000 --- a/board/freescale/common/pq-mds-pib.h +++ /dev/null @@ -1,9 +0,0 @@ -/* - * Copyright (C) 2007 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation; - */ - -extern int pib_init(void); -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 52/76] rmobile: Drop CONFIG_RMOBILE 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (48 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 51/76] freescale: Drop unused pq-mds-pib driver Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 53/76] rtc: Drop old and unused drivers Simon Glass ` (22 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Nobuhiro Iwamatsu This has been renamed to CONFIG_ARCH_RMOBILE but this one was left behind. It doesn't point to a directory that exists, so just drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/arm/cpu/armv7/Makefile | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/cpu/armv7/Makefile b/arch/arm/cpu/armv7/Makefile index 7d7907601ec..653eef8ad79 100644 --- a/arch/arm/cpu/armv7/Makefile +++ b/arch/arm/cpu/armv7/Makefile @@ -37,7 +37,6 @@ obj-$(if $(filter bcm281xx,$(SOC)),y) += bcm281xx/ obj-$(if $(filter bcmcygnus,$(SOC)),y) += bcmcygnus/ obj-$(if $(filter bcmnsp,$(SOC)),y) += bcmnsp/ obj-$(if $(filter ls102xa,$(SOC)),y) += ls102xa/ -obj-$(CONFIG_RMOBILE) += rmobile/ obj-$(if $(filter stv0991,$(SOC)),y) += stv0991/ obj-$(CONFIG_ARCH_SUNXI) += sunxi/ obj-$(CONFIG_VF610) += vf610/ -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 53/76] rtc: Drop old and unused drivers 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (49 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 52/76] rmobile: Drop CONFIG_RMOBILE Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 54/76] mtd: Drop unused CONFIG_S32V234 Simon Glass ` (21 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass These drivers are not used and have not been converted to driver model. Drop them and references to the non-existent CONFIG options they use. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/rtc/Makefile | 14 -- drivers/rtc/at91sam9_rtt.c | 78 ------- drivers/rtc/ds1302.c | 329 ---------------------------- drivers/rtc/ds1306.c | 438 ------------------------------------- drivers/rtc/ftrtc010.c | 122 ----------- drivers/rtc/imxdi.c | 223 ------------------- drivers/rtc/max6900.c | 105 --------- drivers/rtc/mk48t59.c | 175 --------------- drivers/rtc/mx27rtc.c | 64 ------ drivers/rtc/rs5c372.c | 256 ---------------------- drivers/rtc/s3c24x0_rtc.c | 149 ------------- drivers/rtc/x1205.c | 161 -------------- 12 files changed, 2114 deletions(-) delete mode 100644 drivers/rtc/at91sam9_rtt.c delete mode 100644 drivers/rtc/ds1302.c delete mode 100644 drivers/rtc/ds1306.c delete mode 100644 drivers/rtc/ftrtc010.c delete mode 100644 drivers/rtc/imxdi.c delete mode 100644 drivers/rtc/max6900.c delete mode 100644 drivers/rtc/mk48t59.c delete mode 100644 drivers/rtc/mx27rtc.c delete mode 100644 drivers/rtc/rs5c372.c delete mode 100644 drivers/rtc/s3c24x0_rtc.c delete mode 100644 drivers/rtc/x1205.c diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile index acfd130bbc9..447551e15aa 100644 --- a/drivers/rtc/Makefile +++ b/drivers/rtc/Makefile @@ -6,49 +6,35 @@ obj-$(CONFIG_$(SPL_TPL_)DM_RTC) += rtc-uclass.o -obj-$(CONFIG_RTC_AT91SAM9_RTT) += at91sam9_rtt.o obj-$(CONFIG_RTC_ARMADA38X) += armada38x.o obj-$(CONFIG_RTC_DAVINCI) += davinci.o -obj-$(CONFIG_RTC_DS1302) += ds1302.o -obj-$(CONFIG_RTC_DS1306) += ds1306.o obj-$(CONFIG_RTC_DS1307) += ds1307.o obj-$(CONFIG_RTC_DS1338) += ds1307.o -obj-$(CONFIG_RTC_DS1339) += ds1307.o obj-$(CONFIG_RTC_DS1337) += ds1337.o obj-$(CONFIG_RTC_DS1374) += ds1374.o -obj-$(CONFIG_RTC_DS1388) += ds1337.o obj-$(CONFIG_RTC_DS3231) += ds3231.o obj-$(CONFIG_RTC_DS3232) += ds3232.o obj-$(CONFIG_RTC_EMULATION) += emul_rtc.o -obj-$(CONFIG_RTC_FTRTC010) += ftrtc010.o obj-$(CONFIG_RTC_HT1380) += ht1380.o obj-$(CONFIG_SANDBOX) += i2c_rtc_emul.o -obj-$(CONFIG_RTC_IMXDI) += imxdi.o obj-$(CONFIG_RTC_ISL1208) += isl1208.o obj-$(CONFIG_RTC_M41T62) += m41t62.o -obj-$(CONFIG_RTC_MAX6900) += max6900.o obj-$(CONFIG_RTC_MC13XXX) += mc13xxx-rtc.o obj-$(CONFIG_RTC_MC146818) += mc146818.o -obj-$(CONFIG_RTC_MCP79411) += ds1307.o obj-$(CONFIG_MCFRTC) += mcfrtc.o -obj-$(CONFIG_RTC_MK48T59) += mk48t59.o obj-$(CONFIG_RTC_MV) += mvrtc.o -obj-$(CONFIG_RTC_MX27) += mx27rtc.o obj-$(CONFIG_RTC_MXS) += mxsrtc.o obj-$(CONFIG_RTC_PCF8563) += pcf8563.o obj-$(CONFIG_RTC_PCF2127) += pcf2127.o obj-$(CONFIG_RTC_PL031) += pl031.o obj-$(CONFIG_RTC_PT7C4338) += pt7c4338.o -obj-$(CONFIG_RTC_RS5C372A) += rs5c372.o obj-$(CONFIG_RTC_RV3028) += rv3028.o obj-$(CONFIG_RTC_RV3029) += rv3029.o obj-$(CONFIG_RTC_RV8803) += rv8803.o obj-$(CONFIG_RTC_RX8025) += rx8025.o obj-$(CONFIG_RTC_RX8010SJ) += rx8010sj.o -obj-$(CONFIG_RTC_S3C24X0) += s3c24x0_rtc.o obj-$(CONFIG_RTC_S35392A) += s35392a.o obj-$(CONFIG_RTC_STM32) += stm32_rtc.o obj-$(CONFIG_SANDBOX) += sandbox_rtc.o -obj-$(CONFIG_RTC_X1205) += x1205.o obj-$(CONFIG_RTC_ABX80X) += abx80x.o obj-$(CONFIG_RTC_ZYNQMP) += zynqmp_rtc.o diff --git a/drivers/rtc/at91sam9_rtt.c b/drivers/rtc/at91sam9_rtt.c deleted file mode 100644 index 6f92660ef1d..00000000000 --- a/drivers/rtc/at91sam9_rtt.c +++ /dev/null @@ -1,78 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2010 - * Reinhard Meyer, reinhard.meyer@emk-elektronik.de - */ - -/* - * Date & Time support for the internal Real-time Timer - * of AT91SAM9260 and compatibles. - * Compatible with the LinuX rtc driver workaround: - * The RTT cannot be written to, but only reset. - * The actual time is the sum of RTT and one of - * the four GPBR registers. - * - * The at91sam9260 has 4 GPBR (0-3). - * For their typical use see at91_gpbr.h ! - * - * make sure u-boot and kernel use the same GPBR ! - */ - -#include <common.h> -#include <command.h> -#include <rtc.h> -#include <asm/io.h> -#include <linux/errno.h> -#include <asm/arch/hardware.h> -#include <asm/arch/at91_rtt.h> -#include <asm/arch/at91_gpbr.h> - -int rtc_get (struct rtc_time *tmp) -{ - at91_rtt_t *rtt = (at91_rtt_t *) ATMEL_BASE_RTT; - at91_gpbr_t *gpbr = (at91_gpbr_t *) ATMEL_BASE_GPBR; - ulong tim; - ulong tim2; - ulong off; - - do { - tim = readl(&rtt->vr); - tim2 = readl(&rtt->vr); - } while (tim!=tim2); - off = readl(&gpbr->reg[AT91_GPBR_INDEX_TIMEOFF]); - /* off==0 means time is invalid, but we ignore that */ - rtc_to_tm(tim+off, tmp); - return 0; -} - -int rtc_set (struct rtc_time *tmp) -{ - at91_rtt_t *rtt = (at91_rtt_t *) ATMEL_BASE_RTT; - at91_gpbr_t *gpbr = (at91_gpbr_t *) ATMEL_BASE_GPBR; - ulong tim; - - tim = rtc_mktime(tmp); - - /* clear alarm, set prescaler to 32768, clear counter */ - writel(32768+AT91_RTT_RTTRST, &rtt->mr); - writel(~0, &rtt->ar); - writel(tim, &gpbr->reg[AT91_GPBR_INDEX_TIMEOFF]); - /* wait for counter clear to happen, takes less than a 1/32768th second */ - while (readl(&rtt->vr) != 0) - ; - return 0; -} - -void rtc_reset (void) -{ - at91_rtt_t *rtt = (at91_rtt_t *) ATMEL_BASE_RTT; - at91_gpbr_t *gpbr = (at91_gpbr_t *) ATMEL_BASE_GPBR; - - /* clear alarm, set prescaler to 32768, clear counter */ - writel(32768+AT91_RTT_RTTRST, &rtt->mr); - writel(~0, &rtt->ar); - writel(0, &gpbr->reg[AT91_GPBR_INDEX_TIMEOFF]); - /* wait for counter clear to happen, takes less than a 1/32768th second */ - while (readl(&rtt->vr) != 0) - ; -} diff --git a/drivers/rtc/ds1302.c b/drivers/rtc/ds1302.c deleted file mode 100644 index 189607c3e02..00000000000 --- a/drivers/rtc/ds1302.c +++ /dev/null @@ -1,329 +0,0 @@ -/* - * ds1302.c - Support for the Dallas Semiconductor DS1302 Timekeeping Chip - * - * Rex G. Feany <rfeany@zumanetworks.com> - * - */ - -#include <common.h> -#include <command.h> -#include <rtc.h> -#include <linux/delay.h> - -/* GPP Pins */ -#define DATA 0x200 -#define SCLK 0x400 -#define RST 0x800 - -/* Happy Fun Defines(tm) */ -#define RESET rtc_go_low(RST), rtc_go_low(SCLK) -#define N_RESET rtc_go_high(RST), rtc_go_low(SCLK) - -#define CLOCK_HIGH rtc_go_high(SCLK) -#define CLOCK_LOW rtc_go_low(SCLK) - -#define DATA_HIGH rtc_go_high(DATA) -#define DATA_LOW rtc_go_low(DATA) -#define DATA_READ (GTREGREAD(GPP_VALUE) & DATA) - -#undef RTC_DEBUG - -#ifdef RTC_DEBUG -# define DPRINTF(x,args...) printf("ds1302: " x , ##args) -static inline void DUMP(const char *ptr, int num) -{ - while (num--) printf("%x ", *ptr++); - printf("]\n"); -} -#else -# define DPRINTF(x,args...) -# define DUMP(ptr, num) -#endif - -/* time data format for DS1302 */ -struct ds1302_st -{ - unsigned char CH:1; /* clock halt 1=stop 0=start */ - unsigned char sec10:3; - unsigned char sec:4; - - unsigned char zero0:1; - unsigned char min10:3; - unsigned char min:4; - - unsigned char fmt:1; /* 1=12 hour 0=24 hour */ - unsigned char zero1:1; - unsigned char hr10:2; /* 10 (0-2) or am/pm (am/pm, 0-1) */ - unsigned char hr:4; - - unsigned char zero2:2; - unsigned char date10:2; - unsigned char date:4; - - unsigned char zero3:3; - unsigned char month10:1; - unsigned char month:4; - - unsigned char zero4:5; - unsigned char day:3; /* day of week */ - - unsigned char year10:4; - unsigned char year:4; - - unsigned char WP:1; /* write protect 1=protect 0=unprot */ - unsigned char zero5:7; -}; - -static int ds1302_initted=0; - -/* Pin control */ -static inline void -rtc_go_high(unsigned int mask) -{ - unsigned int f = GTREGREAD(GPP_VALUE) | mask; - - GT_REG_WRITE(GPP_VALUE, f); -} - -static inline void -rtc_go_low(unsigned int mask) -{ - unsigned int f = GTREGREAD(GPP_VALUE) & ~mask; - - GT_REG_WRITE(GPP_VALUE, f); -} - -static inline void -rtc_go_input(unsigned int mask) -{ - unsigned int f = GTREGREAD(GPP_IO_CONTROL) & ~mask; - - GT_REG_WRITE(GPP_IO_CONTROL, f); -} - -static inline void -rtc_go_output(unsigned int mask) -{ - unsigned int f = GTREGREAD(GPP_IO_CONTROL) | mask; - - GT_REG_WRITE(GPP_IO_CONTROL, f); -} - -/* Access data in RTC */ - -static void -write_byte(unsigned char b) -{ - int i; - unsigned char mask=1; - - for(i=0;i<8;i++) { - CLOCK_LOW; /* Lower clock */ - (b&mask)?DATA_HIGH:DATA_LOW; /* set data */ - udelay(1); - CLOCK_HIGH; /* latch data with rising clock */ - udelay(1); - mask=mask<<1; - } -} - -static unsigned char -read_byte(void) -{ - int i; - unsigned char mask=1; - unsigned char b=0; - - for(i=0;i<8;i++) { - CLOCK_LOW; - udelay(1); - if (DATA_READ) b|=mask; /* if this bit is high, set in b */ - CLOCK_HIGH; /* clock out next bit */ - udelay(1); - mask=mask<<1; - } - return b; -} - -static void -read_ser_drv(unsigned char addr, unsigned char *buf, int count) -{ - int i; -#ifdef RTC_DEBUG - char *foo = buf; -#endif - - DPRINTF("READ 0x%x bytes @ 0x%x [ ", count, addr); - - addr|=1; /* READ */ - N_RESET; - udelay(4); - write_byte(addr); - rtc_go_input(DATA); /* Put gpp pin into input mode */ - udelay(1); - for(i=0;i<count;i++) *(buf++)=read_byte(); - RESET; - rtc_go_output(DATA);/* Reset gpp for output */ - udelay(4); - - DUMP(foo, count); -} - -static void -write_ser_drv(unsigned char addr, unsigned char *buf, int count) -{ - int i; - - DPRINTF("WRITE 0x%x bytes @ 0x%x [ ", count, addr); - DUMP(buf, count); - - addr&=~1; /* WRITE */ - N_RESET; - udelay(4); - write_byte(addr); - for(i=0;i<count;i++) write_byte(*(buf++)); - RESET; - udelay(4); - -} - -void -rtc_init(void) -{ - struct ds1302_st bbclk; - unsigned char b; - int mod; - - DPRINTF("init\n"); - - rtc_go_output(DATA|SCLK|RST); - - /* disable write protect */ - b = 0; - write_ser_drv(0x8e,&b,1); - - /* enable trickle */ - b = 0xa5; /* 1010.0101 */ - write_ser_drv(0x90,&b,1); - - /* read burst */ - read_ser_drv(0xbe, (unsigned char *)&bbclk, 8); - - /* Sanity checks */ - mod = 0; - if (bbclk.CH) { - printf("ds1302: Clock was halted, starting clock\n"); - bbclk.CH=0; - mod=1; - } - - if (bbclk.fmt) { - printf("ds1302: Clock was in 12 hour mode, fixing\n"); - bbclk.fmt=0; - mod=1; - } - - if (bbclk.year>9) { - printf("ds1302: Year was corrupted, fixing\n"); - bbclk.year10=100/10; /* 2000 - why not? ;) */ - bbclk.year=0; - mod=1; - } - - /* Write out the changes if needed */ - if (mod) { - /* enable write protect */ - bbclk.WP = 1; - write_ser_drv(0xbe,(unsigned char *)&bbclk,8); - } else { - /* Else just turn write protect on */ - b = 0x80; - write_ser_drv(0x8e,&b,1); - } - DPRINTF("init done\n"); - - ds1302_initted=1; -} - -void -rtc_reset(void) -{ - if(!ds1302_initted) rtc_init(); - /* TODO */ -} - -int -rtc_get(struct rtc_time *tmp) -{ - int rel = 0; - struct ds1302_st bbclk; - - if(!ds1302_initted) rtc_init(); - - read_ser_drv(0xbe,(unsigned char *)&bbclk, 8); /* read burst */ - - if (bbclk.CH) { - printf("ds1302: rtc_get: Clock was halted, clock probably " - "corrupt\n"); - rel = -1; - } - - tmp->tm_sec=10*bbclk.sec10+bbclk.sec; - tmp->tm_min=10*bbclk.min10+bbclk.min; - tmp->tm_hour=10*bbclk.hr10+bbclk.hr; - tmp->tm_wday=bbclk.day; - tmp->tm_mday=10*bbclk.date10+bbclk.date; - tmp->tm_mon=10*bbclk.month10+bbclk.month; - tmp->tm_year=10*bbclk.year10+bbclk.year + 1900; - - tmp->tm_yday = 0; - tmp->tm_isdst= 0; - - DPRINTF("Get DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec ); - - return rel; -} - -int rtc_set(struct rtc_time *tmp) -{ - struct ds1302_st bbclk; - unsigned char b=0; - - if(!ds1302_initted) rtc_init(); - - DPRINTF("Set DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec); - - memset(&bbclk,0,sizeof(bbclk)); - bbclk.CH=0; /* dont halt */ - bbclk.WP=1; /* write protect when we're done */ - - bbclk.sec10=tmp->tm_sec/10; - bbclk.sec=tmp->tm_sec%10; - - bbclk.min10=tmp->tm_min/10; - bbclk.min=tmp->tm_min%10; - - bbclk.hr10=tmp->tm_hour/10; - bbclk.hr=tmp->tm_hour%10; - - bbclk.day=tmp->tm_wday; - - bbclk.date10=tmp->tm_mday/10; - bbclk.date=tmp->tm_mday%10; - - bbclk.month10=tmp->tm_mon/10; - bbclk.month=tmp->tm_mon%10; - - tmp->tm_year -= 1900; - bbclk.year10=tmp->tm_year/10; - bbclk.year=tmp->tm_year%10; - - write_ser_drv(0x8e,&b,1); /* disable write protect */ - write_ser_drv(0xbe,(unsigned char *)&bbclk, 8); /* write burst */ - - return 0; -} diff --git a/drivers/rtc/ds1306.c b/drivers/rtc/ds1306.c deleted file mode 100644 index 36d615812b2..00000000000 --- a/drivers/rtc/ds1306.c +++ /dev/null @@ -1,438 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2002 SIXNET, dge@sixnetio.com. - * - * (C) Copyright 2004, Li-Pro.Net <www.li-pro.net> - * Stephan Linz <linz@li-pro.net> - */ - -/* - * Date & Time support for DS1306 RTC using SPI: - * - * - SXNI855T: it uses its own soft SPI here in this file - * - all other: use the external spi_xfer() function - * (see include/spi.h) - */ - -#include <common.h> -#include <command.h> -#include <rtc.h> -#include <spi.h> -#include <linux/delay.h> - -#define RTC_SECONDS 0x00 -#define RTC_MINUTES 0x01 -#define RTC_HOURS 0x02 -#define RTC_DAY_OF_WEEK 0x03 -#define RTC_DATE_OF_MONTH 0x04 -#define RTC_MONTH 0x05 -#define RTC_YEAR 0x06 - -#define RTC_SECONDS_ALARM0 0x07 -#define RTC_MINUTES_ALARM0 0x08 -#define RTC_HOURS_ALARM0 0x09 -#define RTC_DAY_OF_WEEK_ALARM0 0x0a - -#define RTC_SECONDS_ALARM1 0x0b -#define RTC_MINUTES_ALARM1 0x0c -#define RTC_HOURS_ALARM1 0x0d -#define RTC_DAY_OF_WEEK_ALARM1 0x0e - -#define RTC_CONTROL 0x0f -#define RTC_STATUS 0x10 -#define RTC_TRICKLE_CHARGER 0x11 - -#define RTC_USER_RAM_BASE 0x20 - -/* ************************************************************************* */ -#ifdef CONFIG_SXNI855T /* !!! SHOULD BE CHANGED TO NEW CODE !!! */ - -static void soft_spi_send (unsigned char n); -static unsigned char soft_spi_read (void); -static void init_spi (void); - -/*----------------------------------------------------------------------- - * Definitions - */ - -#define PB_SPISCK 0x00000002 /* PB 30 */ -#define PB_SPIMOSI 0x00000004 /* PB 29 */ -#define PB_SPIMISO 0x00000008 /* PB 28 */ -#define PB_SPI_CE 0x00010000 /* PB 15 */ - -/* ------------------------------------------------------------------------- */ - -/* read clock time from DS1306 and return it in *tmp */ -int rtc_get (struct rtc_time *tmp) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - unsigned char spi_byte; /* Data Byte */ - - init_spi (); /* set port B for software SPI */ - - /* Now we can enable the DS1306 RTC */ - immap->im_cpm.cp_pbdat |= PB_SPI_CE; - udelay(10); - - /* Shift out the address (0) of the time in the Clock Chip */ - soft_spi_send (0); - - /* Put the clock readings into the rtc_time structure */ - tmp->tm_sec = bcd2bin (soft_spi_read ()); /* Read seconds */ - tmp->tm_min = bcd2bin (soft_spi_read ()); /* Read minutes */ - - /* Hours are trickier */ - spi_byte = soft_spi_read (); /* Read Hours into temporary value */ - if (spi_byte & 0x40) { - /* 12 hour mode bit is set (time is in 1-12 format) */ - if (spi_byte & 0x20) { - /* since PM we add 11 to get 0-23 for hours */ - tmp->tm_hour = (bcd2bin (spi_byte & 0x1F)) + 11; - } else { - /* since AM we subtract 1 to get 0-23 for hours */ - tmp->tm_hour = (bcd2bin (spi_byte & 0x1F)) - 1; - } - } else { - /* Otherwise, 0-23 hour format */ - tmp->tm_hour = (bcd2bin (spi_byte & 0x3F)); - } - - soft_spi_read (); /* Read and discard Day of week */ - tmp->tm_mday = bcd2bin (soft_spi_read ()); /* Read Day of the Month */ - tmp->tm_mon = bcd2bin (soft_spi_read ()); /* Read Month */ - - /* Read Year and convert to this century */ - tmp->tm_year = bcd2bin (soft_spi_read ()) + 2000; - - /* Now we can disable the DS1306 RTC */ - immap->im_cpm.cp_pbdat &= ~PB_SPI_CE; /* Disable DS1306 Chip */ - udelay(10); - - rtc_calc_weekday(tmp); /* Determine the day of week */ - - debug ("Get DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec); - - return 0; -} - -/* ------------------------------------------------------------------------- */ - -/* set clock time in DS1306 RTC and in MPC8xx RTC */ -int rtc_set (struct rtc_time *tmp) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - - init_spi (); /* set port B for software SPI */ - - /* Now we can enable the DS1306 RTC */ - immap->im_cpm.cp_pbdat |= PB_SPI_CE; /* Enable DS1306 Chip */ - udelay(10); - - /* First disable write protect in the clock chip control register */ - soft_spi_send (0x8F); /* send address of the control register */ - soft_spi_send (0x00); /* send control register contents */ - - /* Now disable the DS1306 to terminate the write */ - immap->im_cpm.cp_pbdat &= ~PB_SPI_CE; - udelay(10); - - /* Now enable the DS1306 to initiate a new write */ - immap->im_cpm.cp_pbdat |= PB_SPI_CE; - udelay(10); - - /* Next, send the address of the clock time write registers */ - soft_spi_send (0x80); /* send address of the first time register */ - - /* Use Burst Mode to send all of the time data to the clock */ - bin2bcd (tmp->tm_sec); - soft_spi_send (bin2bcd (tmp->tm_sec)); /* Send Seconds */ - soft_spi_send (bin2bcd (tmp->tm_min)); /* Send Minutes */ - soft_spi_send (bin2bcd (tmp->tm_hour)); /* Send Hour */ - soft_spi_send (bin2bcd (tmp->tm_wday)); /* Send Day of the Week */ - soft_spi_send (bin2bcd (tmp->tm_mday)); /* Send Day of Month */ - soft_spi_send (bin2bcd (tmp->tm_mon)); /* Send Month */ - soft_spi_send (bin2bcd (tmp->tm_year - 2000)); /* Send Year */ - - /* Now we can disable the Clock chip to terminate the burst write */ - immap->im_cpm.cp_pbdat &= ~PB_SPI_CE; /* Disable DS1306 Chip */ - udelay(10); - - /* Now we can enable the Clock chip to initiate a new write */ - immap->im_cpm.cp_pbdat |= PB_SPI_CE; /* Enable DS1306 Chip */ - udelay(10); - - /* First we Enable write protect in the clock chip control register */ - soft_spi_send (0x8F); /* send address of the control register */ - soft_spi_send (0x40); /* send out Control Register contents */ - - /* Now disable the DS1306 */ - immap->im_cpm.cp_pbdat &= ~PB_SPI_CE; /* Disable DS1306 Chip */ - udelay(10); - - /* Set standard MPC8xx clock to the same time so Linux will - * see the time even if it doesn't have a DS1306 clock driver. - * This helps with experimenting with standard kernels. - */ - { - ulong tim; - - tim = rtc_mktime(tmp); - - immap->im_sitk.sitk_rtck = KAPWR_KEY; - immap->im_sit.sit_rtc = tim; - } - - debug ("Set DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec); - - return 0; -} - -/* ------------------------------------------------------------------------- */ - -/* Initialize Port B for software SPI */ -static void init_spi (void) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - - /* Force output pins to begin at logic 0 */ - immap->im_cpm.cp_pbdat &= ~(PB_SPI_CE | PB_SPIMOSI | PB_SPISCK); - - /* Set these 3 signals as outputs */ - immap->im_cpm.cp_pbdir |= (PB_SPIMOSI | PB_SPI_CE | PB_SPISCK); - - immap->im_cpm.cp_pbdir &= ~PB_SPIMISO; /* Make MISO pin an input */ - udelay(10); -} - -/* ------------------------------------------------------------------------- */ - -/* NOTE: soft_spi_send() assumes that the I/O lines are configured already */ -static void soft_spi_send (unsigned char n) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - unsigned char bitpos; /* bit position to receive */ - unsigned char i; /* Loop Control */ - - /* bit position to send, start with most significant bit */ - bitpos = 0x80; - - /* Send 8 bits to software SPI */ - for (i = 0; i < 8; i++) { /* Loop for 8 bits */ - immap->im_cpm.cp_pbdat |= PB_SPISCK; /* Raise SCK */ - - if (n & bitpos) - immap->im_cpm.cp_pbdat |= PB_SPIMOSI; /* Set MOSI to 1 */ - else - immap->im_cpm.cp_pbdat &= ~PB_SPIMOSI; /* Set MOSI to 0 */ - udelay(10); - - immap->im_cpm.cp_pbdat &= ~PB_SPISCK; /* Lower SCK */ - udelay(10); - - bitpos >>= 1; /* Shift for next bit position */ - } -} - -/* ------------------------------------------------------------------------- */ - -/* NOTE: soft_spi_read() assumes that the I/O lines are configured already */ -static unsigned char soft_spi_read (void) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - - unsigned char spi_byte = 0; /* Return value, assume success */ - unsigned char bitpos; /* bit position to receive */ - unsigned char i; /* Loop Control */ - - /* bit position to receive, start with most significant bit */ - bitpos = 0x80; - - /* Read 8 bits here */ - for (i = 0; i < 8; i++) { /* Do 8 bits in loop */ - immap->im_cpm.cp_pbdat |= PB_SPISCK; /* Raise SCK */ - udelay(10); - if (immap->im_cpm.cp_pbdat & PB_SPIMISO) /* Get a bit of data */ - spi_byte |= bitpos; /* Set data accordingly */ - immap->im_cpm.cp_pbdat &= ~PB_SPISCK; /* Lower SCK */ - udelay(10); - bitpos >>= 1; /* Shift for next bit position */ - } - - return spi_byte; /* Return the byte read */ -} - -/* ------------------------------------------------------------------------- */ - -void rtc_reset (void) -{ - return; /* nothing to do */ -} - -#else /* not CONFIG_SXNI855T */ -/* ************************************************************************* */ - -static unsigned char rtc_read (unsigned char reg); -static void rtc_write (unsigned char reg, unsigned char val); - -static struct spi_slave *slave; - -/* read clock time from DS1306 and return it in *tmp */ -int rtc_get (struct rtc_time *tmp) -{ - unsigned char sec, min, hour, mday, wday, mon, year; - - /* - * Assuming Vcc = 2.0V (lowest speed) - * - * REVISIT: If we add an rtc_init() function we can do this - * step just once. - */ - if (!slave) { - slave = spi_setup_slave(0, CONFIG_SYS_SPI_RTC_DEVID, 600000, - SPI_MODE_3 | SPI_CS_HIGH); - if (!slave) - return; - } - - if (spi_claim_bus(slave)) - return; - - sec = rtc_read (RTC_SECONDS); - min = rtc_read (RTC_MINUTES); - hour = rtc_read (RTC_HOURS); - mday = rtc_read (RTC_DATE_OF_MONTH); - wday = rtc_read (RTC_DAY_OF_WEEK); - mon = rtc_read (RTC_MONTH); - year = rtc_read (RTC_YEAR); - - spi_release_bus(slave); - - debug ("Get RTC year: %02x mon: %02x mday: %02x wday: %02x " - "hr: %02x min: %02x sec: %02x\n", - year, mon, mday, wday, hour, min, sec); - debug ("Alarms[0]: wday: %02x hour: %02x min: %02x sec: %02x\n", - rtc_read (RTC_DAY_OF_WEEK_ALARM0), - rtc_read (RTC_HOURS_ALARM0), - rtc_read (RTC_MINUTES_ALARM0), rtc_read (RTC_SECONDS_ALARM0)); - debug ("Alarms[1]: wday: %02x hour: %02x min: %02x sec: %02x\n", - rtc_read (RTC_DAY_OF_WEEK_ALARM1), - rtc_read (RTC_HOURS_ALARM1), - rtc_read (RTC_MINUTES_ALARM1), rtc_read (RTC_SECONDS_ALARM1)); - - tmp->tm_sec = bcd2bin (sec & 0x7F); /* convert Seconds */ - tmp->tm_min = bcd2bin (min & 0x7F); /* convert Minutes */ - - /* convert Hours */ - tmp->tm_hour = (hour & 0x40) - ? ((hour & 0x20) /* 12 hour mode */ - ? bcd2bin (hour & 0x1F) + 11 /* PM */ - : bcd2bin (hour & 0x1F) - 1 /* AM */ - ) - : bcd2bin (hour & 0x3F); /* 24 hour mode */ - - tmp->tm_mday = bcd2bin (mday & 0x3F); /* convert Day of the Month */ - tmp->tm_mon = bcd2bin (mon & 0x1F); /* convert Month */ - tmp->tm_year = bcd2bin (year) + 2000; /* convert Year */ - tmp->tm_wday = bcd2bin (wday & 0x07) - 1; /* convert Day of the Week */ - tmp->tm_yday = 0; - tmp->tm_isdst = 0; - - debug ("Get DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec); - - return 0; -} - -/* ------------------------------------------------------------------------- */ - -/* set clock time from *tmp in DS1306 RTC */ -int rtc_set (struct rtc_time *tmp) -{ - /* Assuming Vcc = 2.0V (lowest speed) */ - if (!slave) { - slave = spi_setup_slave(0, CONFIG_SYS_SPI_RTC_DEVID, 600000, - SPI_MODE_3 | SPI_CS_HIGH); - if (!slave) - return; - } - - if (spi_claim_bus(slave)) - return; - - debug ("Set DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec); - - rtc_write (RTC_SECONDS, bin2bcd (tmp->tm_sec)); - rtc_write (RTC_MINUTES, bin2bcd (tmp->tm_min)); - rtc_write (RTC_HOURS, bin2bcd (tmp->tm_hour)); - rtc_write (RTC_DAY_OF_WEEK, bin2bcd (tmp->tm_wday + 1)); - rtc_write (RTC_DATE_OF_MONTH, bin2bcd (tmp->tm_mday)); - rtc_write (RTC_MONTH, bin2bcd (tmp->tm_mon)); - rtc_write (RTC_YEAR, bin2bcd (tmp->tm_year - 2000)); - - spi_release_bus(slave); -} - -/* ------------------------------------------------------------------------- */ - -/* reset the DS1306 */ -void rtc_reset (void) -{ - /* Assuming Vcc = 2.0V (lowest speed) */ - if (!slave) { - slave = spi_setup_slave(0, CONFIG_SYS_SPI_RTC_DEVID, 600000, - SPI_MODE_3 | SPI_CS_HIGH); - if (!slave) - return; - } - - if (spi_claim_bus(slave)) - return; - - /* clear the control register */ - rtc_write (RTC_CONTROL, 0x00); /* 1st step: reset WP */ - rtc_write (RTC_CONTROL, 0x00); /* 2nd step: reset 1Hz, AIE1, AIE0 */ - - /* reset all alarms */ - rtc_write (RTC_SECONDS_ALARM0, 0x00); - rtc_write (RTC_SECONDS_ALARM1, 0x00); - rtc_write (RTC_MINUTES_ALARM0, 0x00); - rtc_write (RTC_MINUTES_ALARM1, 0x00); - rtc_write (RTC_HOURS_ALARM0, 0x00); - rtc_write (RTC_HOURS_ALARM1, 0x00); - rtc_write (RTC_DAY_OF_WEEK_ALARM0, 0x00); - rtc_write (RTC_DAY_OF_WEEK_ALARM1, 0x00); - - spi_release_bus(slave); -} - -/* ------------------------------------------------------------------------- */ - -static unsigned char rtc_read (unsigned char reg) -{ - int ret; - - ret = spi_w8r8(slave, reg); - return ret < 0 ? 0 : ret; -} - -/* ------------------------------------------------------------------------- */ - -static void rtc_write (unsigned char reg, unsigned char val) -{ - unsigned char dout[2]; /* SPI Output Data Bytes */ - unsigned char din[2]; /* SPI Input Data Bytes */ - - dout[0] = 0x80 | reg; - dout[1] = val; - - spi_xfer (slave, 16, dout, din, SPI_XFER_BEGIN | SPI_XFER_END); -} - -#endif /* end of code exclusion (see #ifdef CONFIG_SXNI855T above) */ diff --git a/drivers/rtc/ftrtc010.c b/drivers/rtc/ftrtc010.c deleted file mode 100644 index e384922f473..00000000000 --- a/drivers/rtc/ftrtc010.c +++ /dev/null @@ -1,122 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Faraday FTRTC010 Real Time Clock - * - * (C) Copyright 2009 Faraday Technology - * Po-Yu Chuang <ratbert@faraday-tech.com> - */ - -#include <config.h> -#include <common.h> -#include <log.h> -#include <rtc.h> -#include <asm/io.h> - -struct ftrtc010 { - unsigned int sec; /* 0x00 */ - unsigned int min; /* 0x04 */ - unsigned int hour; /* 0x08 */ - unsigned int day; /* 0x0c */ - unsigned int alarm_sec; /* 0x10 */ - unsigned int alarm_min; /* 0x14 */ - unsigned int alarm_hour; /* 0x18 */ - unsigned int record; /* 0x1c */ - unsigned int cr; /* 0x20 */ - unsigned int wsec; /* 0x24 */ - unsigned int wmin; /* 0x28 */ - unsigned int whour; /* 0x2c */ - unsigned int wday; /* 0x30 */ - unsigned int intr; /* 0x34 */ - unsigned int div; /* 0x38 */ - unsigned int rev; /* 0x3c */ -}; - -/* - * RTC Control Register - */ -#define FTRTC010_CR_ENABLE (1 << 0) -#define FTRTC010_CR_INTERRUPT_SEC (1 << 1) /* per second irq */ -#define FTRTC010_CR_INTERRUPT_MIN (1 << 2) /* per minute irq */ -#define FTRTC010_CR_INTERRUPT_HR (1 << 3) /* per hour irq */ -#define FTRTC010_CR_INTERRUPT_DAY (1 << 4) /* per day irq */ - -static struct ftrtc010 *rtc = (struct ftrtc010 *)CONFIG_FTRTC010_BASE; - -static void ftrtc010_enable(void) -{ - writel(FTRTC010_CR_ENABLE, &rtc->cr); -} - -/* - * return current time in seconds - */ -static unsigned long ftrtc010_time(void) -{ - unsigned long day; - unsigned long hour; - unsigned long minute; - unsigned long second; - unsigned long second2; - - do { - second = readl(&rtc->sec); - day = readl(&rtc->day); - hour = readl(&rtc->hour); - minute = readl(&rtc->min); - second2 = readl(&rtc->sec); - } while (second != second2); - - return day * 24 * 60 * 60 + hour * 60 * 60 + minute * 60 + second; -} - -/* - * Get the current time from the RTC - */ - -int rtc_get(struct rtc_time *tmp) -{ - unsigned long now; - - debug("%s(): record register: %x\n", - __func__, readl(&rtc->record)); - -#ifdef CFG_FTRTC010_PCLK - now = (ftrtc010_time() + readl(&rtc->record)) / RTC_DIV_COUNT; -#else /* CFG_FTRTC010_EXTCLK */ - now = ftrtc010_time() + readl(&rtc->record); -#endif - - rtc_to_tm(now, tmp); - - return 0; -} - -/* - * Set the RTC - */ -int rtc_set(struct rtc_time *tmp) -{ - unsigned long new; - unsigned long now; - - debug("%s(): DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - __func__, - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec); - - new = rtc_mktime(tmp); - - now = ftrtc010_time(); - - debug("%s(): write %lx to record register\n", __func__, new - now); - - writel(new - now, &rtc->record); - - return 0; -} - -void rtc_reset(void) -{ - debug("%s()\n", __func__); - ftrtc010_enable(); -} diff --git a/drivers/rtc/imxdi.c b/drivers/rtc/imxdi.c deleted file mode 100644 index e3a1393266c..00000000000 --- a/drivers/rtc/imxdi.c +++ /dev/null @@ -1,223 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2009-2012 ADVANSEE - * Benoît Thébaudeau <benoit.thebaudeau@advansee.com> - * - * Based on the Linux rtc-imxdi.c driver, which is: - * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved. - * Copyright 2010 Orex Computed Radiography - */ - -/* - * Date & Time support for Freescale i.MX DryIce RTC - */ - -#include <common.h> -#include <command.h> -#include <linux/compat.h> -#include <rtc.h> -#include <linux/delay.h> - -#include <asm/io.h> -#include <asm/arch/imx-regs.h> - -/* DryIce Register Definitions */ - -struct imxdi_regs { - u32 dtcmr; /* Time Counter MSB Reg */ - u32 dtclr; /* Time Counter LSB Reg */ - u32 dcamr; /* Clock Alarm MSB Reg */ - u32 dcalr; /* Clock Alarm LSB Reg */ - u32 dcr; /* Control Reg */ - u32 dsr; /* Status Reg */ - u32 dier; /* Interrupt Enable Reg */ -}; - -#define DCAMR_UNSET 0xFFFFFFFF /* doomsday - 1 sec */ - -#define DCR_TCE (1 << 3) /* Time Counter Enable */ - -#define DSR_WBF (1 << 10) /* Write Busy Flag */ -#define DSR_WNF (1 << 9) /* Write Next Flag */ -#define DSR_WCF (1 << 8) /* Write Complete Flag */ -#define DSR_WEF (1 << 7) /* Write Error Flag */ -#define DSR_CAF (1 << 4) /* Clock Alarm Flag */ -#define DSR_NVF (1 << 1) /* Non-Valid Flag */ -#define DSR_SVF (1 << 0) /* Security Violation Flag */ - -#define DIER_WNIE (1 << 9) /* Write Next Interrupt Enable */ -#define DIER_WCIE (1 << 8) /* Write Complete Interrupt Enable */ -#define DIER_WEIE (1 << 7) /* Write Error Interrupt Enable */ -#define DIER_CAIE (1 << 4) /* Clock Alarm Interrupt Enable */ - -/* Driver Private Data */ - -struct imxdi_data { - struct imxdi_regs __iomem *regs; - int init_done; -}; - -static struct imxdi_data data; - -/* - * This function attempts to clear the dryice write-error flag. - * - * A dryice write error is similar to a bus fault and should not occur in - * normal operation. Clearing the flag requires another write, so the root - * cause of the problem may need to be fixed before the flag can be cleared. - */ -static void clear_write_error(void) -{ - int cnt; - - puts("### Warning: RTC - Register write error!\n"); - - /* clear the write error flag */ - __raw_writel(DSR_WEF, &data.regs->dsr); - - /* wait for it to take effect */ - for (cnt = 0; cnt < 1000; cnt++) { - if ((__raw_readl(&data.regs->dsr) & DSR_WEF) == 0) - return; - udelay(10); - } - puts("### Error: RTC - Cannot clear write-error flag!\n"); -} - -/* - * Write a dryice register and wait until it completes. - * - * Use interrupt flags to determine when the write has completed. - */ -#define DI_WRITE_WAIT(val, reg) \ -( \ - /* do the register write */ \ - __raw_writel((val), &data.regs->reg), \ - \ - di_write_wait((val), #reg) \ -) -static int di_write_wait(u32 val, const char *reg) -{ - int cnt; - int ret = 0; - int rc = 0; - - /* wait for the write to finish */ - for (cnt = 0; cnt < 100; cnt++) { - if ((__raw_readl(&data.regs->dsr) & (DSR_WCF | DSR_WEF)) != 0) { - ret = 1; - break; - } - udelay(10); - } - if (ret == 0) - printf("### Warning: RTC - Write-wait timeout " - "val = 0x%.8x reg = %s\n", val, reg); - - /* check for write error */ - if (__raw_readl(&data.regs->dsr) & DSR_WEF) { - clear_write_error(); - rc = -1; - } - - return rc; -} - -/* - * Initialize dryice hardware - */ -static int di_init(void) -{ - int rc = 0; - - data.regs = (struct imxdi_regs __iomem *)IMX_DRYICE_BASE; - - /* mask all interrupts */ - __raw_writel(0, &data.regs->dier); - - /* put dryice into valid state */ - if (__raw_readl(&data.regs->dsr) & DSR_NVF) { - rc = DI_WRITE_WAIT(DSR_NVF | DSR_SVF, dsr); - if (rc) - goto err; - } - - /* initialize alarm */ - rc = DI_WRITE_WAIT(DCAMR_UNSET, dcamr); - if (rc) - goto err; - rc = DI_WRITE_WAIT(0, dcalr); - if (rc) - goto err; - - /* clear alarm flag */ - if (__raw_readl(&data.regs->dsr) & DSR_CAF) { - rc = DI_WRITE_WAIT(DSR_CAF, dsr); - if (rc) - goto err; - } - - /* the timer won't count if it has never been written to */ - if (__raw_readl(&data.regs->dtcmr) == 0) { - rc = DI_WRITE_WAIT(0, dtcmr); - if (rc) - goto err; - } - - /* start keeping time */ - if (!(__raw_readl(&data.regs->dcr) & DCR_TCE)) { - rc = DI_WRITE_WAIT(__raw_readl(&data.regs->dcr) | DCR_TCE, dcr); - if (rc) - goto err; - } - - data.init_done = 1; - return 0; - -err: - return rc; -} - -int rtc_get(struct rtc_time *tmp) -{ - unsigned long now; - int rc = 0; - - if (!data.init_done) { - rc = di_init(); - if (rc) - goto err; - } - - now = __raw_readl(&data.regs->dtcmr); - rtc_to_tm(now, tmp); - -err: - return rc; -} - -int rtc_set(struct rtc_time *tmp) -{ - unsigned long now; - int rc; - - if (!data.init_done) { - rc = di_init(); - if (rc) - goto err; - } - - now = rtc_mktime(tmp); - /* zero the fractional part first */ - rc = DI_WRITE_WAIT(0, dtclr); - if (rc == 0) - rc = DI_WRITE_WAIT(now, dtcmr); - -err: - return rc; -} - -void rtc_reset(void) -{ - di_init(); -} diff --git a/drivers/rtc/max6900.c b/drivers/rtc/max6900.c deleted file mode 100644 index e03a87f94da..00000000000 --- a/drivers/rtc/max6900.c +++ /dev/null @@ -1,105 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -/* - * Date & Time support for MAXIM MAX6900 RTC - */ - -/* #define DEBUG */ - -#include <common.h> -#include <command.h> -#include <rtc.h> -#include <i2c.h> -#include <linux/delay.h> - -#ifndef CFG_SYS_I2C_RTC_ADDR -#define CFG_SYS_I2C_RTC_ADDR 0x50 -#endif - -/* ------------------------------------------------------------------------- */ - -static uchar rtc_read (uchar reg) -{ - return (i2c_reg_read (CFG_SYS_I2C_RTC_ADDR, reg)); -} - -static void rtc_write (uchar reg, uchar val) -{ - i2c_reg_write (CFG_SYS_I2C_RTC_ADDR, reg, val); - udelay(2500); -} - -/* ------------------------------------------------------------------------- */ - -int rtc_get (struct rtc_time *tmp) -{ - uchar sec, min, hour, mday, wday, mon, cent, year; - int retry = 1; - - do { - sec = rtc_read (0x80); - min = rtc_read (0x82); - hour = rtc_read (0x84); - mday = rtc_read (0x86); - mon = rtc_read (0x88); - wday = rtc_read (0x8a); - year = rtc_read (0x8c); - cent = rtc_read (0x92); - /* - * Check for seconds rollover - */ - if ((sec != 59) || (rtc_read(0x80) == sec)){ - retry = 0; - } - } while (retry); - - debug ( "Get RTC year: %02x mon: %02x cent: %02x mday: %02x wday: %02x " - "hr: %02x min: %02x sec: %02x\n", - year, mon, cent, mday, wday, - hour, min, sec ); - - tmp->tm_sec = bcd2bin (sec & 0x7F); - tmp->tm_min = bcd2bin (min & 0x7F); - tmp->tm_hour = bcd2bin (hour & 0x3F); - tmp->tm_mday = bcd2bin (mday & 0x3F); - tmp->tm_mon = bcd2bin (mon & 0x1F); - tmp->tm_year = bcd2bin (year) + bcd2bin(cent) * 100; - tmp->tm_wday = bcd2bin (wday & 0x07); - tmp->tm_yday = 0; - tmp->tm_isdst= 0; - - debug ( "Get DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec); - - return 0; -} - -int rtc_set (struct rtc_time *tmp) -{ - - debug ( "Set DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec); - - rtc_write (0x9E, 0x00); - rtc_write (0x80, 0); /* Clear seconds to ensure no rollover */ - rtc_write (0x92, bin2bcd(tmp->tm_year / 100)); - rtc_write (0x8c, bin2bcd(tmp->tm_year % 100)); - rtc_write (0x8a, bin2bcd(tmp->tm_wday)); - rtc_write (0x88, bin2bcd(tmp->tm_mon)); - rtc_write (0x86, bin2bcd(tmp->tm_mday)); - rtc_write (0x84, bin2bcd(tmp->tm_hour)); - rtc_write (0x82, bin2bcd(tmp->tm_min )); - rtc_write (0x80, bin2bcd(tmp->tm_sec )); - - return 0; -} - -void rtc_reset (void) -{ -} diff --git a/drivers/rtc/mk48t59.c b/drivers/rtc/mk48t59.c deleted file mode 100644 index 8c90a704076..00000000000 --- a/drivers/rtc/mk48t59.c +++ /dev/null @@ -1,175 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2001 Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Andreas Heppel <aheppel@sysgo.de> - */ - -/* - * Date & Time support for the MK48T59 RTC - */ - -#undef RTC_DEBUG - -#include <common.h> -#include <command.h> -#include <config.h> -#include <rtc.h> -#include <mk48t59.h> - -#if defined(CONFIG_BAB7xx) - -static uchar rtc_read (short reg) -{ - out8(RTC_PORT_ADDR0, reg & 0xFF); - out8(RTC_PORT_ADDR1, (reg>>8) & 0xFF); - return in8(RTC_PORT_DATA); -} - -static void rtc_write (short reg, uchar val) -{ - out8(RTC_PORT_ADDR0, reg & 0xFF); - out8(RTC_PORT_ADDR1, (reg>>8) & 0xFF); - out8(RTC_PORT_DATA, val); -} - -#elif defined(CONFIG_EVAL5200) - -static uchar rtc_read (short reg) -{ - return in8(RTC(reg)); -} - -static void rtc_write (short reg, uchar val) -{ - out8(RTC(reg),val); -} - -#else -# error Board specific rtc access functions should be supplied -#endif - -/* ------------------------------------------------------------------------- */ - -void *nvram_read(void *dest, const short src, size_t count) -{ - uchar *d = (uchar *) dest; - short s = src; - - while (count--) - *d++ = rtc_read(s++); - - return dest; -} - -void nvram_write(short dest, const void *src, size_t count) -{ - short d = dest; - uchar *s = (uchar *) src; - - while (count--) - rtc_write(d++, *s++); -} - -/* ------------------------------------------------------------------------- */ - -int rtc_get (struct rtc_time *tmp) -{ - uchar save_ctrl_a; - uchar sec, min, hour, mday, wday, mon, year; - - /* Simple: freeze the clock, read it and allow updates again */ - save_ctrl_a = rtc_read(RTC_CONTROLA); - - /* Set the register to read the value. */ - save_ctrl_a |= RTC_CA_READ; - rtc_write(RTC_CONTROLA, save_ctrl_a); - - sec = rtc_read (RTC_SECONDS); - min = rtc_read (RTC_MINUTES); - hour = rtc_read (RTC_HOURS); - mday = rtc_read (RTC_DAY_OF_MONTH); - wday = rtc_read (RTC_DAY_OF_WEEK); - mon = rtc_read (RTC_MONTH); - year = rtc_read (RTC_YEAR); - - /* re-enable update */ - save_ctrl_a &= ~RTC_CA_READ; - rtc_write(RTC_CONTROLA, save_ctrl_a); - -#ifdef RTC_DEBUG - printf ( "Get RTC year: %02x mon/cent: %02x mday: %02x wday: %02x " - "hr: %02x min: %02x sec: %02x\n", - year, mon, mday, wday, - hour, min, sec ); -#endif - tmp->tm_sec = bcd2bin (sec & 0x7F); - tmp->tm_min = bcd2bin (min & 0x7F); - tmp->tm_hour = bcd2bin (hour & 0x3F); - tmp->tm_mday = bcd2bin (mday & 0x3F); - tmp->tm_mon = bcd2bin (mon & 0x1F); - tmp->tm_year = bcd2bin (year); - tmp->tm_wday = bcd2bin (wday & 0x07); - if(tmp->tm_year<70) - tmp->tm_year+=2000; - else - tmp->tm_year+=1900; - tmp->tm_yday = 0; - tmp->tm_isdst= 0; -#ifdef RTC_DEBUG - printf ( "Get DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec); -#endif - - return 0; -} - -int rtc_set (struct rtc_time *tmp) -{ - uchar save_ctrl_a; - -#ifdef RTC_DEBUG - printf ( "Set DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec); -#endif - save_ctrl_a = rtc_read(RTC_CONTROLA); - - save_ctrl_a |= RTC_CA_WRITE; - rtc_write(RTC_CONTROLA, save_ctrl_a); /* disables the RTC to update the regs */ - - rtc_write (RTC_YEAR, bin2bcd(tmp->tm_year % 100)); - rtc_write (RTC_MONTH, bin2bcd(tmp->tm_mon)); - - rtc_write (RTC_DAY_OF_WEEK, bin2bcd(tmp->tm_wday)); - rtc_write (RTC_DAY_OF_MONTH, bin2bcd(tmp->tm_mday)); - rtc_write (RTC_HOURS, bin2bcd(tmp->tm_hour)); - rtc_write (RTC_MINUTES, bin2bcd(tmp->tm_min )); - rtc_write (RTC_SECONDS, bin2bcd(tmp->tm_sec )); - - save_ctrl_a &= ~RTC_CA_WRITE; - rtc_write(RTC_CONTROLA, save_ctrl_a); /* enables the RTC to update the regs */ - - return 0; -} - -void rtc_reset (void) -{ - uchar control_b; - - /* - * Start oscillator here. - */ - control_b = rtc_read(RTC_CONTROLB); - - control_b &= ~RTC_CB_STOP; - rtc_write(RTC_CONTROLB, control_b); -} - -void rtc_set_watchdog(short multi, short res) -{ - uchar wd_value; - - wd_value = RTC_WDS | ((multi & 0x1F) << 2) | (res & 0x3); - rtc_write(RTC_WATCHDOG, wd_value); -} diff --git a/drivers/rtc/mx27rtc.c b/drivers/rtc/mx27rtc.c deleted file mode 100644 index 563e8a4a361..00000000000 --- a/drivers/rtc/mx27rtc.c +++ /dev/null @@ -1,64 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Freescale i.MX27 RTC Driver - * - * Copyright (C) 2012 Philippe Reynes <tremyfr@yahoo.fr> - */ - -#include <common.h> -#include <rtc.h> -#include <asm/io.h> -#include <asm/arch/imx-regs.h> - -#define HOUR_SHIFT 8 -#define HOUR_MASK 0x1f -#define MIN_SHIFT 0 -#define MIN_MASK 0x3f - -int rtc_get(struct rtc_time *time) -{ - struct rtc_regs *rtc_regs = (struct rtc_regs *)IMX_RTC_BASE; - uint32_t day, hour, min, sec; - - day = readl(&rtc_regs->dayr); - hour = readl(&rtc_regs->hourmin); - sec = readl(&rtc_regs->seconds); - - min = (hour >> MIN_SHIFT) & MIN_MASK; - hour = (hour >> HOUR_SHIFT) & HOUR_MASK; - - sec += min * 60 + hour * 3600 + day * 24 * 3600; - - rtc_to_tm(sec, time); - - return 0; -} - -int rtc_set(struct rtc_time *time) -{ - struct rtc_regs *rtc_regs = (struct rtc_regs *)IMX_RTC_BASE; - uint32_t day, hour, min, sec; - - sec = rtc_mktime(time); - - day = sec / (24 * 3600); - sec = sec % (24 * 3600); - hour = sec / 3600; - sec = sec % 3600; - min = sec / 60; - sec = sec % 60; - - hour = (hour & HOUR_MASK) << HOUR_SHIFT; - hour |= (min & MIN_MASK) << MIN_SHIFT; - - writel(day, &rtc_regs->dayr); - writel(hour, &rtc_regs->hourmin); - writel(sec, &rtc_regs->seconds); - - return 0; -} - -void rtc_reset(void) -{ - /* nothing to do */ -} diff --git a/drivers/rtc/rs5c372.c b/drivers/rtc/rs5c372.c deleted file mode 100644 index 6b1c23ca5db..00000000000 --- a/drivers/rtc/rs5c372.c +++ /dev/null @@ -1,256 +0,0 @@ -/* - * rs5c372.c - * - * Device driver for Ricoh's Real Time Controller RS5C372A. - * - * Copyright (C) 2004 Gary Jennejohn garyj@denx.de - * - * Based in part in ds1307.c - - * (C) Copyright 2001, 2002, 2003 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * Keith Outwater, keith_outwater@mvis.com` - * Steven Scholz, steven.scholz@imc-berlin.de - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <common.h> -#include <command.h> -#include <rtc.h> -#include <i2c.h> - -/* - * Reads are always done starting with register 15, which requires some - * jumping-through-hoops to access the data correctly. - * - * Writes are always done starting with register 0. - */ - -#define DEBUG 0 - -#if DEBUG -static unsigned int rtc_debug = DEBUG; -#else -#define rtc_debug 0 /* gcc will remove all the debug code for us */ -#endif - -#ifndef CFG_SYS_I2C_RTC_ADDR -#define CFG_SYS_I2C_RTC_ADDR 0x32 -#endif - -#define RS5C372_RAM_SIZE 0x10 -#define RATE_32000HZ 0x80 /* Rate Select 32.000KHz */ -#define RATE_32768HZ 0x00 /* Rate Select 32.768KHz */ - -#define STATUS_XPT 0x10 /* data invalid because voltage was 0 */ - -#define USE_24HOUR_MODE 0x20 -#define TWELVE_HOUR_MODE(n) ((((n) >> 5) & 1) == 0) -#define HOURS_AP(n) (((n) >> 5) & 1) -#define HOURS_12(n) bcd2bin((n) & 0x1F) -#define HOURS_24(n) bcd2bin((n) & 0x3F) - - -static int setup_done = 0; - -static int -rs5c372_readram(unsigned char *buf, int len) -{ - int ret; - - ret = i2c_read(CFG_SYS_I2C_RTC_ADDR, 0, 0, buf, len); - if (ret != 0) { - printf("%s: failed to read\n", __FUNCTION__); - return ret; - } - - if (buf[0] & STATUS_XPT) - printf("### Warning: RTC lost power\n"); - - return ret; -} - -static void -rs5c372_enable(void) -{ - unsigned char buf[RS5C372_RAM_SIZE + 1]; - int ret; - - /* note that this returns reg. 15 in buf[1] */ - ret = rs5c372_readram(&buf[1], RS5C372_RAM_SIZE); - if (ret != 0) { - printf("%s: failed\n", __FUNCTION__); - return; - } - - buf[0] = 0; - /* we want to start writing at register 0 so we have to copy the */ - /* register contents up one slot */ - for (ret = 2; ret < 9; ret++) - buf[ret - 1] = buf[ret]; - /* registers 0 to 6 (time values) are not touched */ - buf[8] = RATE_32768HZ; /* reg. 7 */ - buf[9] = 0; /* reg. 8 */ - buf[10] = 0; /* reg. 9 */ - buf[11] = 0; /* reg. 10 */ - buf[12] = 0; /* reg. 11 */ - buf[13] = 0; /* reg. 12 */ - buf[14] = 0; /* reg. 13 */ - buf[15] = 0; /* reg. 14 */ - buf[16] = USE_24HOUR_MODE; /* reg. 15 */ - ret = i2c_write(CFG_SYS_I2C_RTC_ADDR, 0, 0, buf, RS5C372_RAM_SIZE+1); - if (ret != 0) { - printf("%s: failed\n", __FUNCTION__); - return; - } - setup_done = 1; - - return; -} - -static void -rs5c372_convert_to_time(struct rtc_time *dt, unsigned char *buf) -{ - /* buf[0] is register 15 */ - dt->tm_sec = bcd2bin(buf[1]); - dt->tm_min = bcd2bin(buf[2]); - - if (TWELVE_HOUR_MODE(buf[0])) { - dt->tm_hour = HOURS_12(buf[3]); - if (HOURS_AP(buf[3])) /* PM */ - dt->tm_hour += 12; - } else /* 24-hour-mode */ - dt->tm_hour = HOURS_24(buf[3]); - - dt->tm_mday = bcd2bin(buf[5]); - dt->tm_mon = bcd2bin(buf[6]); - dt->tm_year = bcd2bin(buf[7]); - if (dt->tm_year >= 70) - dt->tm_year += 1900; - else - dt->tm_year += 2000; - /* 0 is Sunday */ - dt->tm_wday = bcd2bin(buf[4] & 0x07); - dt->tm_yday = 0; - dt->tm_isdst= 0; - - if(rtc_debug > 2) { - printf("rs5c372_convert_to_time: year = %d\n", dt->tm_year); - printf("rs5c372_convert_to_time: mon = %d\n", dt->tm_mon); - printf("rs5c372_convert_to_time: mday = %d\n", dt->tm_mday); - printf("rs5c372_convert_to_time: hour = %d\n", dt->tm_hour); - printf("rs5c372_convert_to_time: min = %d\n", dt->tm_min); - printf("rs5c372_convert_to_time: sec = %d\n", dt->tm_sec); - } -} - -/* - * Get the current time from the RTC - */ -int -rtc_get (struct rtc_time *tmp) -{ - unsigned char buf[RS5C372_RAM_SIZE]; - int ret; - - if (!setup_done) - rs5c372_enable(); - - if (!setup_done) - return -1; - - memset(buf, 0, sizeof(buf)); - - /* note that this returns reg. 15 in buf[0] */ - ret = rs5c372_readram(buf, RS5C372_RAM_SIZE); - if (ret != 0) { - printf("%s: failed\n", __FUNCTION__); - return -1; - } - - rs5c372_convert_to_time(tmp, buf); - - return 0; -} - -/* - * Set the RTC - */ -int rtc_set (struct rtc_time *tmp) -{ - unsigned char buf[8], reg15; - int ret; - - if (!setup_done) - rs5c372_enable(); - - if (!setup_done) - return -1; - - if(rtc_debug > 2) { - printf("rtc_set: tm_year = %d\n", tmp->tm_year); - printf("rtc_set: tm_mon = %d\n", tmp->tm_mon); - printf("rtc_set: tm_mday = %d\n", tmp->tm_mday); - printf("rtc_set: tm_hour = %d\n", tmp->tm_hour); - printf("rtc_set: tm_min = %d\n", tmp->tm_min); - printf("rtc_set: tm_sec = %d\n", tmp->tm_sec); - } - - memset(buf, 0, sizeof(buf)); - - /* only read register 15 */ - ret = i2c_read(CFG_SYS_I2C_RTC_ADDR, 0, 0, buf, 1); - - if (ret == 0) { - /* need to save register 15 */ - reg15 = buf[0]; - buf[0] = 0; /* register address on RS5C372 */ - buf[1] = bin2bcd(tmp->tm_sec); - buf[2] = bin2bcd(tmp->tm_min); - /* need to handle 12 hour mode */ - if (TWELVE_HOUR_MODE(reg15)) { - if (tmp->tm_hour >= 12) { /* PM */ - /* 12 PM is a special case */ - if (tmp->tm_hour == 12) - buf[3] = bin2bcd(tmp->tm_hour); - else - buf[3] = bin2bcd(tmp->tm_hour - 12); - buf[3] |= 0x20; - } - } else { - buf[3] = bin2bcd(tmp->tm_hour); - } - - buf[4] = bin2bcd(tmp->tm_wday); - buf[5] = bin2bcd(tmp->tm_mday); - buf[6] = bin2bcd(tmp->tm_mon); - if (tmp->tm_year < 1970 || tmp->tm_year > 2069) - printf("WARNING: year should be between 1970 and 2069!\n"); - buf[7] = bin2bcd(tmp->tm_year % 100); - - ret = i2c_write(CFG_SYS_I2C_RTC_ADDR, 0, 0, buf, 8); - if (ret != 0) { - printf("rs5c372_set_datetime(), i2c_master_send() returned %d\n",ret); - return -1; - } - } else { - return -1; - } - - return 0; -} - -/* - * Reset the RTC. - */ -void -rtc_reset (void) -{ - if (!setup_done) - rs5c372_enable(); -} diff --git a/drivers/rtc/s3c24x0_rtc.c b/drivers/rtc/s3c24x0_rtc.c deleted file mode 100644 index 96ea3cf878e..00000000000 --- a/drivers/rtc/s3c24x0_rtc.c +++ /dev/null @@ -1,149 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2003 - * David Müller ELSOFT AG Switzerland. d.mueller@elsoft.ch - */ - -/* - * Date & Time support for the built-in Samsung S3C24X0 RTC - */ - -#include <common.h> -#include <command.h> - -#include <asm/arch/s3c24x0_cpu.h> - -#include <rtc.h> -#include <asm/io.h> -#include <linux/compiler.h> - -typedef enum { - RTC_ENABLE, - RTC_DISABLE -} RTC_ACCESS; - - -static inline void SetRTC_Access(RTC_ACCESS a) -{ - struct s3c24x0_rtc *rtc = s3c24x0_get_base_rtc(); - - switch (a) { - case RTC_ENABLE: - writeb(readb(&rtc->rtccon) | 0x01, &rtc->rtccon); - break; - - case RTC_DISABLE: - writeb(readb(&rtc->rtccon) & ~0x01, &rtc->rtccon); - break; - } -} - -/* ------------------------------------------------------------------------- */ - -int rtc_get(struct rtc_time *tmp) -{ - struct s3c24x0_rtc *rtc = s3c24x0_get_base_rtc(); - uchar sec, min, hour, mday, wday, mon, year; - __maybe_unused uchar a_sec, a_min, a_hour, a_date, - a_mon, a_year, a_armed; - - /* enable access to RTC registers */ - SetRTC_Access(RTC_ENABLE); - - /* read RTC registers */ - do { - sec = readb(&rtc->bcdsec); - min = readb(&rtc->bcdmin); - hour = readb(&rtc->bcdhour); - mday = readb(&rtc->bcddate); - wday = readb(&rtc->bcdday); - mon = readb(&rtc->bcdmon); - year = readb(&rtc->bcdyear); - } while (sec != readb(&rtc->bcdsec)); - - /* read ALARM registers */ - a_sec = readb(&rtc->almsec); - a_min = readb(&rtc->almmin); - a_hour = readb(&rtc->almhour); - a_date = readb(&rtc->almdate); - a_mon = readb(&rtc->almmon); - a_year = readb(&rtc->almyear); - a_armed = readb(&rtc->rtcalm); - - /* disable access to RTC registers */ - SetRTC_Access(RTC_DISABLE); - -#ifdef RTC_DEBUG - printf("Get RTC year: %02x mon/cent: %02x mday: %02x wday: %02x " - "hr: %02x min: %02x sec: %02x\n", - year, mon, mday, wday, hour, min, sec); - printf("Alarms: %02x: year: %02x month: %02x date: %02x hour: " - "%02x min: %02x sec: %02x\n", - a_armed, a_year, a_mon, a_date, a_hour, a_min, a_sec); -#endif - - tmp->tm_sec = bcd2bin(sec & 0x7F); - tmp->tm_min = bcd2bin(min & 0x7F); - tmp->tm_hour = bcd2bin(hour & 0x3F); - tmp->tm_mday = bcd2bin(mday & 0x3F); - tmp->tm_mon = bcd2bin(mon & 0x1F); - tmp->tm_year = bcd2bin(year); - tmp->tm_wday = bcd2bin(wday & 0x07); - if (tmp->tm_year < 70) - tmp->tm_year += 2000; - else - tmp->tm_year += 1900; - tmp->tm_yday = 0; - tmp->tm_isdst = 0; -#ifdef RTC_DEBUG - printf("Get DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec); -#endif - - return 0; -} - -int rtc_set(struct rtc_time *tmp) -{ - struct s3c24x0_rtc *rtc = s3c24x0_get_base_rtc(); - uchar sec, min, hour, mday, wday, mon, year; - -#ifdef RTC_DEBUG - printf("Set DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, - tmp->tm_hour, tmp->tm_min, tmp->tm_sec); -#endif - year = bin2bcd(tmp->tm_year % 100); - mon = bin2bcd(tmp->tm_mon); - wday = bin2bcd(tmp->tm_wday); - mday = bin2bcd(tmp->tm_mday); - hour = bin2bcd(tmp->tm_hour); - min = bin2bcd(tmp->tm_min); - sec = bin2bcd(tmp->tm_sec); - - /* enable access to RTC registers */ - SetRTC_Access(RTC_ENABLE); - - /* write RTC registers */ - writeb(sec, &rtc->bcdsec); - writeb(min, &rtc->bcdmin); - writeb(hour, &rtc->bcdhour); - writeb(mday, &rtc->bcddate); - writeb(wday, &rtc->bcdday); - writeb(mon, &rtc->bcdmon); - writeb(year, &rtc->bcdyear); - - /* disable access to RTC registers */ - SetRTC_Access(RTC_DISABLE); - - return 0; -} - -void rtc_reset(void) -{ - struct s3c24x0_rtc *rtc = s3c24x0_get_base_rtc(); - - writeb((readb(&rtc->rtccon) & ~0x06) | 0x08, &rtc->rtccon); - writeb(readb(&rtc->rtccon) & ~(0x08 | 0x01), &rtc->rtccon); -} diff --git a/drivers/rtc/x1205.c b/drivers/rtc/x1205.c deleted file mode 100644 index 4a8d1c5903f..00000000000 --- a/drivers/rtc/x1205.c +++ /dev/null @@ -1,161 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * based on a the Linux rtc-x1207.c driver which is: - * Copyright 2004 Karen Spearel - * Copyright 2005 Alessandro Zummo - * - * Information and datasheet: - * http://www.intersil.com/cda/deviceinfo/0,1477,X1205,00.html - */ - -/* - * Date & Time support for Xicor/Intersil X1205 RTC - */ - -/* #define DEBUG */ - -#include <common.h> -#include <command.h> -#include <log.h> -#include <rtc.h> -#include <i2c.h> - -#define CCR_SEC 0 -#define CCR_MIN 1 -#define CCR_HOUR 2 -#define CCR_MDAY 3 -#define CCR_MONTH 4 -#define CCR_YEAR 5 -#define CCR_WDAY 6 -#define CCR_Y2K 7 - -#define X1205_REG_SR 0x3F /* status register */ -#define X1205_REG_Y2K 0x37 -#define X1205_REG_DW 0x36 -#define X1205_REG_YR 0x35 -#define X1205_REG_MO 0x34 -#define X1205_REG_DT 0x33 -#define X1205_REG_HR 0x32 -#define X1205_REG_MN 0x31 -#define X1205_REG_SC 0x30 -#define X1205_REG_DTR 0x13 -#define X1205_REG_ATR 0x12 -#define X1205_REG_INT 0x11 -#define X1205_REG_0 0x10 -#define X1205_REG_Y2K1 0x0F -#define X1205_REG_DWA1 0x0E -#define X1205_REG_YRA1 0x0D -#define X1205_REG_MOA1 0x0C -#define X1205_REG_DTA1 0x0B -#define X1205_REG_HRA1 0x0A -#define X1205_REG_MNA1 0x09 -#define X1205_REG_SCA1 0x08 -#define X1205_REG_Y2K0 0x07 -#define X1205_REG_DWA0 0x06 -#define X1205_REG_YRA0 0x05 -#define X1205_REG_MOA0 0x04 -#define X1205_REG_DTA0 0x03 -#define X1205_REG_HRA0 0x02 -#define X1205_REG_MNA0 0x01 -#define X1205_REG_SCA0 0x00 - -#define X1205_CCR_BASE 0x30 /* Base address of CCR */ -#define X1205_ALM0_BASE 0x00 /* Base address of ALARM0 */ - -#define X1205_SR_RTCF 0x01 /* Clock failure */ -#define X1205_SR_WEL 0x02 /* Write Enable Latch */ -#define X1205_SR_RWEL 0x04 /* Register Write Enable */ - -#define X1205_DTR_DTR0 0x01 -#define X1205_DTR_DTR1 0x02 -#define X1205_DTR_DTR2 0x04 - -#define X1205_HR_MIL 0x80 /* Set in ccr.hour for 24 hr mode */ - -static void rtc_write(int reg, u8 val) -{ - i2c_write(CFG_SYS_I2C_RTC_ADDR, reg, 2, &val, 1); -} - -/* - * In the routines that deal directly with the x1205 hardware, we use - * rtc_time -- month 0-11, hour 0-23, yr = calendar year-epoch - * Epoch is initialized as 2000. Time is set to UTC. - */ -int rtc_get(struct rtc_time *tm) -{ - u8 buf[8]; - - i2c_read(CFG_SYS_I2C_RTC_ADDR, X1205_CCR_BASE, 2, buf, 8); - - debug("%s: raw read data - sec=%02x, min=%02x, hr=%02x, " - "mday=%02x, mon=%02x, year=%02x, wday=%02x, y2k=%02x\n", - __FUNCTION__, - buf[0], buf[1], buf[2], buf[3], - buf[4], buf[5], buf[6], buf[7]); - - tm->tm_sec = bcd2bin(buf[CCR_SEC]); - tm->tm_min = bcd2bin(buf[CCR_MIN]); - tm->tm_hour = bcd2bin(buf[CCR_HOUR] & 0x3F); /* hr is 0-23 */ - tm->tm_mday = bcd2bin(buf[CCR_MDAY]); - tm->tm_mon = bcd2bin(buf[CCR_MONTH]); /* mon is 0-11 */ - tm->tm_year = bcd2bin(buf[CCR_YEAR]) - + (bcd2bin(buf[CCR_Y2K]) * 100); - tm->tm_wday = buf[CCR_WDAY]; - - debug("%s: tm is secs=%d, mins=%d, hours=%d, " - "mday=%d, mon=%d, year=%d, wday=%d\n", - __FUNCTION__, - tm->tm_sec, tm->tm_min, tm->tm_hour, - tm->tm_mday, tm->tm_mon, tm->tm_year, tm->tm_wday); - - return 0; -} - -int rtc_set(struct rtc_time *tm) -{ - int i; - u8 buf[8]; - - debug("Set DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", - tm->tm_year, tm->tm_mon, tm->tm_mday, tm->tm_wday, - tm->tm_hour, tm->tm_min, tm->tm_sec); - - buf[CCR_SEC] = bin2bcd(tm->tm_sec); - buf[CCR_MIN] = bin2bcd(tm->tm_min); - - /* set hour and 24hr bit */ - buf[CCR_HOUR] = bin2bcd(tm->tm_hour) | X1205_HR_MIL; - - buf[CCR_MDAY] = bin2bcd(tm->tm_mday); - - /* month, 1 - 12 */ - buf[CCR_MONTH] = bin2bcd(tm->tm_mon); - - /* year, since the rtc epoch*/ - buf[CCR_YEAR] = bin2bcd(tm->tm_year % 100); - buf[CCR_WDAY] = tm->tm_wday & 0x07; - buf[CCR_Y2K] = bin2bcd(tm->tm_year / 100); - - /* this sequence is required to unlock the chip */ - rtc_write(X1205_REG_SR, X1205_SR_WEL); - rtc_write(X1205_REG_SR, X1205_SR_WEL | X1205_SR_RWEL); - - /* write register's data */ - for (i = 0; i < 8; i++) - rtc_write(X1205_CCR_BASE + i, buf[i]); - - rtc_write(X1205_REG_SR, 0); - - return 0; -} - -void rtc_reset(void) -{ - /* - * Nothing to do - */ -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 54/76] mtd: Drop unused CONFIG_S32V234 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (50 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 53/76] rtc: Drop old and unused drivers Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 55/76] mtd: Drop unused scf0403_lcd driver Simon Glass ` (20 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This option does not exist, so the Makefile rule does nothing. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/arm/cpu/armv8/Makefile | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/cpu/armv8/Makefile b/arch/arm/cpu/armv8/Makefile index 2e4bf9e038c..bba4f570dbb 100644 --- a/arch/arm/cpu/armv8/Makefile +++ b/arch/arm/cpu/armv8/Makefile @@ -39,7 +39,6 @@ obj-$(CONFIG_SPL_RECOVER_DATA_SECTION) += spl_data.o endif obj-$(CONFIG_FSL_LAYERSCAPE) += fsl-layerscape/ -obj-$(CONFIG_S32V234) += s32v234/ obj-$(CONFIG_TARGET_HIKEY) += hisilicon/ obj-$(CONFIG_ARMV8_PSCI) += psci.o obj-$(CONFIG_TARGET_BCMNS3) += bcmns3/ -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 55/76] mtd: Drop unused scf0403_lcd driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (51 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 54/76] mtd: Drop unused CONFIG_S32V234 Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 56/76] rmobile: Drop CONFIG_SH73A0 and associated code Simon Glass ` (19 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used since this commit: 76386d6195a arm: Remove cm_t35 board Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/video/Makefile | 1 - drivers/video/scf0403_lcd.c | 297 ------------------------------------ include/scf0403_lcd.h | 10 -- 3 files changed, 308 deletions(-) delete mode 100644 drivers/video/scf0403_lcd.c delete mode 100644 include/scf0403_lcd.h diff --git a/drivers/video/Makefile b/drivers/video/Makefile index 12b68cdd068..ce2d61d56bc 100644 --- a/drivers/video/Makefile +++ b/drivers/video/Makefile @@ -34,7 +34,6 @@ obj-$(CONFIG_LOGICORE_DP_TX) += logicore_dp_tx.o obj-$(CONFIG_NXP_TDA19988) += tda19988.o obj-$(CONFIG_OSD) += video_osd-uclass.o obj-$(CONFIG_SANDBOX_OSD) += sandbox_osd.o -obj-$(CONFIG_SCF0403_LCD) += scf0403_lcd.o obj-$(CONFIG_VIDEO_ARM_MALIDP) += mali_dp.o obj-$(CONFIG_VIDEO_BCM2835) += bcm2835.o obj-$(CONFIG_VIDEO_BROADWELL_IGD) += broadwell_igd.o diff --git a/drivers/video/scf0403_lcd.c b/drivers/video/scf0403_lcd.c deleted file mode 100644 index 54f0f88b4c9..00000000000 --- a/drivers/video/scf0403_lcd.c +++ /dev/null @@ -1,297 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * scf0403.c -- support for DataImage SCF0403 LCD - * - * Copyright (c) 2013 Adapted from Linux driver: - * Copyright (c) 2012 Anders Electronics plc. All Rights Reserved. - * Copyright (c) 2012 CompuLab, Ltd - * Dmitry Lifshitz <lifshitz@compulab.co.il> - * Ilya Ledvich <ilya@compulab.co.il> - * Inspired by Alberto Panizzo <maramaopercheseimorto@gmail.com> & - * Marek Vasut work in l4f00242t03.c - * - * U-Boot port: Nikita Kiryanov <nikita@compulab.co.il> - */ - -#include <common.h> -#include <malloc.h> -#include <asm/gpio.h> -#include <spi.h> -#include <linux/delay.h> - -struct scf0403_cmd { - u16 cmd; - u16 *params; - int count; -}; - -struct scf0403_initseq_entry { - struct scf0403_cmd cmd; - int delay_ms; -}; - -struct scf0403_priv { - struct spi_slave *spi; - unsigned int reset_gpio; - u32 rddid; - struct scf0403_initseq_entry *init_seq; - int seq_size; -}; - -struct scf0403_priv priv; - -#define SCF0403852GGU04_ID 0x000080 - -/* SCF0403526GGU20 model commands parameters */ -static u16 extcmd_params_sn20[] = {0xff, 0x98, 0x06}; -static u16 spiinttype_params_sn20[] = {0x60}; -static u16 bc_params_sn20[] = { - 0x01, 0x10, 0x61, 0x74, 0x01, 0x01, 0x1B, - 0x12, 0x71, 0x00, 0x00, 0x00, 0x01, 0x01, - 0x05, 0x00, 0xFF, 0xF2, 0x01, 0x00, 0x40, -}; -static u16 bd_params_sn20[] = {0x01, 0x23, 0x45, 0x67, 0x01, 0x23, 0x45, 0x67}; -static u16 be_params_sn20[] = { - 0x01, 0x22, 0x22, 0xBA, 0xDC, 0x26, 0x28, 0x22, 0x22, -}; -static u16 vcom_params_sn20[] = {0x74}; -static u16 vmesur_params_sn20[] = {0x7F, 0x0F, 0x00}; -static u16 powerctl_params_sn20[] = {0x03, 0x0b, 0x00}; -static u16 lvglvolt_params_sn20[] = {0x08}; -static u16 engsetting_params_sn20[] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x20}; -static u16 dispfunc_params_sn20[] = {0xa0}; -static u16 dvddvolt_params_sn20[] = {0x74}; -static u16 dispinv_params_sn20[] = {0x00, 0x00, 0x00}; -static u16 panelres_params_sn20[] = {0x82}; -static u16 framerate_params_sn20[] = {0x00, 0x13, 0x13}; -static u16 timing_params_sn20[] = {0x80, 0x05, 0x40, 0x28}; -static u16 powerctl2_params_sn20[] = {0x17, 0x75, 0x79, 0x20}; -static u16 memaccess_params_sn20[] = {0x00}; -static u16 pixfmt_params_sn20[] = {0x66}; -static u16 pgamma_params_sn20[] = { - 0x00, 0x03, 0x0b, 0x0c, 0x0e, 0x08, 0xc5, 0x04, - 0x08, 0x0c, 0x13, 0x11, 0x11, 0x14, 0x0c, 0x10, -}; -static u16 ngamma_params_sn20[] = { - 0x00, 0x0d, 0x11, 0x0c, 0x0c, 0x04, 0x76, 0x03, - 0x08, 0x0b, 0x16, 0x10, 0x0d, 0x16, 0x0a, 0x00, -}; -static u16 tearing_params_sn20[] = {0x00}; - -/* SCF0403852GGU04 model commands parameters */ -static u16 memaccess_params_sn04[] = {0x08}; -static u16 pixfmt_params_sn04[] = {0x66}; -static u16 modectl_params_sn04[] = {0x01}; -static u16 dispfunc_params_sn04[] = {0x22, 0xe2, 0xFF, 0x04}; -static u16 vcom_params_sn04[] = {0x00, 0x6A}; -static u16 pgamma_params_sn04[] = { - 0x00, 0x07, 0x0d, 0x10, 0x13, 0x19, 0x0f, 0x0c, - 0x05, 0x08, 0x06, 0x13, 0x0f, 0x30, 0x20, 0x1f, -}; -static u16 ngamma_params_sn04[] = { - 0x1F, 0x20, 0x30, 0x0F, 0x13, 0x06, 0x08, 0x05, - 0x0C, 0x0F, 0x19, 0x13, 0x10, 0x0D, 0x07, 0x00, -}; -static u16 dispinv_params_sn04[] = {0x02}; - -/* Common commands */ -static struct scf0403_cmd scf0403_cmd_slpout = {0x11, NULL, 0}; -static struct scf0403_cmd scf0403_cmd_dison = {0x29, NULL, 0}; - -/* SCF0403852GGU04 init sequence */ -static struct scf0403_initseq_entry scf0403_initseq_sn04[] = { - {{0x36, memaccess_params_sn04, ARRAY_SIZE(memaccess_params_sn04)}, 0}, - {{0x3A, pixfmt_params_sn04, ARRAY_SIZE(pixfmt_params_sn04)}, 0}, - {{0xB6, dispfunc_params_sn04, ARRAY_SIZE(dispfunc_params_sn04)}, 0}, - {{0xC5, vcom_params_sn04, ARRAY_SIZE(vcom_params_sn04)}, 0}, - {{0xE0, pgamma_params_sn04, ARRAY_SIZE(pgamma_params_sn04)}, 0}, - {{0xE1, ngamma_params_sn04, ARRAY_SIZE(ngamma_params_sn04)}, 20}, - {{0xB0, modectl_params_sn04, ARRAY_SIZE(modectl_params_sn04)}, 0}, - {{0xB4, dispinv_params_sn04, ARRAY_SIZE(dispinv_params_sn04)}, 100}, -}; - -/* SCF0403526GGU20 init sequence */ -static struct scf0403_initseq_entry scf0403_initseq_sn20[] = { - {{0xff, extcmd_params_sn20, ARRAY_SIZE(extcmd_params_sn20)}, 0}, - {{0xba, spiinttype_params_sn20, ARRAY_SIZE(spiinttype_params_sn20)}, 0}, - {{0xbc, bc_params_sn20, ARRAY_SIZE(bc_params_sn20)}, 0}, - {{0xbd, bd_params_sn20, ARRAY_SIZE(bd_params_sn20)}, 0}, - {{0xbe, be_params_sn20, ARRAY_SIZE(be_params_sn20)}, 0}, - {{0xc7, vcom_params_sn20, ARRAY_SIZE(vcom_params_sn20)}, 0}, - {{0xed, vmesur_params_sn20, ARRAY_SIZE(vmesur_params_sn20)}, 0}, - {{0xc0, powerctl_params_sn20, ARRAY_SIZE(powerctl_params_sn20)}, 0}, - {{0xfc, lvglvolt_params_sn20, ARRAY_SIZE(lvglvolt_params_sn20)}, 0}, - {{0xb6, dispfunc_params_sn20, ARRAY_SIZE(dispfunc_params_sn20)}, 0}, - {{0xdf, engsetting_params_sn20, ARRAY_SIZE(engsetting_params_sn20)}, 0}, - {{0xf3, dvddvolt_params_sn20, ARRAY_SIZE(dvddvolt_params_sn20)}, 0}, - {{0xb4, dispinv_params_sn20, ARRAY_SIZE(dispinv_params_sn20)}, 0}, - {{0xf7, panelres_params_sn20, ARRAY_SIZE(panelres_params_sn20)}, 0}, - {{0xb1, framerate_params_sn20, ARRAY_SIZE(framerate_params_sn20)}, 0}, - {{0xf2, timing_params_sn20, ARRAY_SIZE(timing_params_sn20)}, 0}, - {{0xc1, powerctl2_params_sn20, ARRAY_SIZE(powerctl2_params_sn20)}, 0}, - {{0x36, memaccess_params_sn20, ARRAY_SIZE(memaccess_params_sn20)}, 0}, - {{0x3a, pixfmt_params_sn20, ARRAY_SIZE(pixfmt_params_sn20)}, 0}, - {{0xe0, pgamma_params_sn20, ARRAY_SIZE(pgamma_params_sn20)}, 0}, - {{0xe1, ngamma_params_sn20, ARRAY_SIZE(ngamma_params_sn20)}, 0}, - {{0x35, tearing_params_sn20, ARRAY_SIZE(tearing_params_sn20)}, 0}, -}; - -static void scf0403_gpio_reset(unsigned int gpio) -{ - if (!gpio_is_valid(gpio)) - return; - - gpio_set_value(gpio, 1); - mdelay(100); - gpio_set_value(gpio, 0); - mdelay(40); - gpio_set_value(gpio, 1); - mdelay(100); -} - -static int scf0403_spi_read_rddid(struct spi_slave *spi, u32 *rddid) -{ - int error = 0; - u8 ids_buf = 0x00; - u16 dummy_buf = 0x00; - u16 cmd = 0x04; - - error = spi_set_wordlen(spi, 9); - if (error) - return error; - - /* Here 9 bits required to transmit a command */ - error = spi_xfer(spi, 9, &cmd, NULL, SPI_XFER_ONCE); - if (error) - return error; - - /* - * Here 8 + 1 bits required to arrange extra clock cycle - * before the first data bit. - * According to the datasheet - first parameter is the dummy data. - */ - error = spi_xfer(spi, 9, NULL, &dummy_buf, SPI_XFER_ONCE); - if (error) - return error; - - error = spi_set_wordlen(spi, 8); - if (error) - return error; - - /* Read rest of the data */ - error = spi_xfer(spi, 8, NULL, &ids_buf, SPI_XFER_ONCE); - if (error) - return error; - - *rddid = ids_buf; - - return 0; -} - -static int scf0403_spi_transfer(struct spi_slave *spi, struct scf0403_cmd *cmd) -{ - int i, error; - u32 command = cmd->cmd; - u32 msg; - - error = spi_set_wordlen(spi, 9); - if (error) - return error; - - error = spi_xfer(spi, 9, &command, NULL, SPI_XFER_ONCE); - if (error) - return error; - - for (i = 0; i < cmd->count; i++) { - msg = (cmd->params[i] | 0x100); - error = spi_xfer(spi, 9, &msg, NULL, SPI_XFER_ONCE); - if (error) - return error; - } - - return 0; -} - -static void scf0403_lcd_init(struct scf0403_priv *priv) -{ - int i; - - /* reset LCD */ - scf0403_gpio_reset(priv->reset_gpio); - - for (i = 0; i < priv->seq_size; i++) { - if (scf0403_spi_transfer(priv->spi, &priv->init_seq[i].cmd) < 0) - puts("SPI transfer failed\n"); - - mdelay(priv->init_seq[i].delay_ms); - } -} - -static int scf0403_request_reset_gpio(unsigned gpio) -{ - int err = gpio_request(gpio, "lcd reset"); - - if (err) - return err; - - err = gpio_direction_output(gpio, 0); - if (err) - gpio_free(gpio); - - return err; -} - -int scf0403_init(int reset_gpio) -{ - int error; - - if (gpio_is_valid(reset_gpio)) { - error = scf0403_request_reset_gpio(reset_gpio); - if (error) { - printf("Failed requesting reset GPIO%d: %d\n", - reset_gpio, error); - return error; - } - } - - priv.reset_gpio = reset_gpio; - priv.spi = spi_setup_slave(3, 0, 1000000, SPI_MODE_0); - error = spi_claim_bus(priv.spi); - if (error) - goto bus_claim_fail; - - /* reset LCD */ - scf0403_gpio_reset(reset_gpio); - - error = scf0403_spi_read_rddid(priv.spi, &priv.rddid); - if (error) { - puts("IDs read failed\n"); - goto readid_fail; - } - - if (priv.rddid == SCF0403852GGU04_ID) { - priv.init_seq = scf0403_initseq_sn04; - priv.seq_size = ARRAY_SIZE(scf0403_initseq_sn04); - } else { - priv.init_seq = scf0403_initseq_sn20; - priv.seq_size = ARRAY_SIZE(scf0403_initseq_sn20); - } - - scf0403_lcd_init(&priv); - - /* Start operation */ - scf0403_spi_transfer(priv.spi, &scf0403_cmd_dison); - mdelay(100); - scf0403_spi_transfer(priv.spi, &scf0403_cmd_slpout); - spi_release_bus(priv.spi); - - return 0; - -readid_fail: - spi_release_bus(priv.spi); -bus_claim_fail: - if (gpio_is_valid(priv.reset_gpio)) - gpio_free(priv.reset_gpio); - - return error; -} diff --git a/include/scf0403_lcd.h b/include/scf0403_lcd.h deleted file mode 100644 index 07f8c643ba5..00000000000 --- a/include/scf0403_lcd.h +++ /dev/null @@ -1,10 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (c) 2013, Compulab Inc. - */ -#ifndef SCF0403_LCD_H_ -#define SCF0403_LCD_H_ - -int scf0403_init(int reset_gpio); - -#endif -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 56/76] rmobile: Drop CONFIG_SH73A0 and associated code 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (52 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 55/76] mtd: Drop unused scf0403_lcd driver Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 57/76] sh4: Drop unused pci_sh7780 driver Simon Glass ` (18 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Nobuhiro Iwamatsu This option does not exist, so the code attached to it is not used. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/arm/mach-rmobile/Makefile | 1 - arch/arm/mach-rmobile/cpu_info-sh73a0.c | 43 - arch/arm/mach-rmobile/cpu_info.c | 1 - arch/arm/mach-rmobile/include/mach/gpio.h | 5 +- arch/arm/mach-rmobile/include/mach/rmobile.h | 5 +- .../mach-rmobile/include/mach/sh73a0-gpio.h | 553 ---- arch/arm/mach-rmobile/include/mach/sh73a0.h | 289 -- arch/arm/mach-rmobile/pfc-sh73a0.c | 2807 ----------------- drivers/i2c/sh_i2c.c | 5 - drivers/serial/serial_sh.h | 10 +- 10 files changed, 4 insertions(+), 3715 deletions(-) delete mode 100644 arch/arm/mach-rmobile/cpu_info-sh73a0.c delete mode 100644 arch/arm/mach-rmobile/include/mach/sh73a0-gpio.h delete mode 100644 arch/arm/mach-rmobile/include/mach/sh73a0.h delete mode 100644 arch/arm/mach-rmobile/pfc-sh73a0.c diff --git a/arch/arm/mach-rmobile/Makefile b/arch/arm/mach-rmobile/Makefile index 3f77760e50d..5b86221bc25 100644 --- a/arch/arm/mach-rmobile/Makefile +++ b/arch/arm/mach-rmobile/Makefile @@ -8,7 +8,6 @@ obj-y += emac.o obj-$(CONFIG_DISPLAY_BOARDINFO) += board.o obj-$(CONFIG_TMU_TIMER) += ../../sh/lib/time.o -obj-$(CONFIG_SH73A0) += lowlevel_init.o cpu_info-sh73a0.o pfc-sh73a0.o obj-$(CONFIG_R8A7740) += lowlevel_init.o cpu_info-r8a7740.o pfc-r8a7740.o obj-$(CONFIG_RCAR_GEN2) += lowlevel_init_ca15.o cpu_info-rcar.o obj-$(CONFIG_RCAR_GEN3) += lowlevel_init_gen3.o cpu_info-rcar.o memmap-gen3.o diff --git a/arch/arm/mach-rmobile/cpu_info-sh73a0.c b/arch/arm/mach-rmobile/cpu_info-sh73a0.c deleted file mode 100644 index 0c7ee8acf5a..00000000000 --- a/arch/arm/mach-rmobile/cpu_info-sh73a0.c +++ /dev/null @@ -1,43 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2012 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> - * (C) Copyright 2012 Renesas Solutions Corp. - */ -#include <common.h> -#include <asm/io.h> - -u32 rmobile_get_cpu_type(void) -{ - u32 id; - u32 type; - struct sh73a0_hpb *hpb = (struct sh73a0_hpb *)HPB_BASE; - - id = readl(&hpb->cccr); - type = (id >> 8) & 0xFF; - - return type; -} - -u32 rmobile_get_cpu_rev_integer(void) -{ - u32 id; - u32 rev; - struct sh73a0_hpb *hpb = (struct sh73a0_hpb *)HPB_BASE; - - id = readl(&hpb->cccr); - rev = ((id >> 4) & 0xF) + 1; - - return rev; -} - -u32 rmobile_get_cpu_rev_fraction(void) -{ - u32 id; - u32 rev; - struct sh73a0_hpb *hpb = (struct sh73a0_hpb *)HPB_BASE; - - id = readl(&hpb->cccr); - rev = id & 0xF; - - return rev; -} diff --git a/arch/arm/mach-rmobile/cpu_info.c b/arch/arm/mach-rmobile/cpu_info.c index bd9e71707f5..246029ac294 100644 --- a/arch/arm/mach-rmobile/cpu_info.c +++ b/arch/arm/mach-rmobile/cpu_info.c @@ -62,7 +62,6 @@ static const struct { u16 cpu_type; u8 cpu_name[10]; } rmobile_cpuinfo[] = { - { RMOBILE_CPU_TYPE_SH73A0, "SH73A0" }, { RMOBILE_CPU_TYPE_R8A7740, "R8A7740" }, { RMOBILE_CPU_TYPE_R8A7790, "R8A7790" }, { RMOBILE_CPU_TYPE_R8A7791, "R8A7791" }, diff --git a/arch/arm/mach-rmobile/include/mach/gpio.h b/arch/arm/mach-rmobile/include/mach/gpio.h index 6b5e4ed4eb5..150aa46034d 100644 --- a/arch/arm/mach-rmobile/include/mach/gpio.h +++ b/arch/arm/mach-rmobile/include/mach/gpio.h @@ -1,10 +1,7 @@ #ifndef __ASM_ARCH_GPIO_H #define __ASM_ARCH_GPIO_H -#if defined(CONFIG_SH73A0) -#include "sh73a0-gpio.h" -void sh73a0_pinmux_init(void); -#elif defined(CONFIG_R8A7740) +#if defined(CONFIG_R8A7740) #include "r8a7740-gpio.h" void r8a7740_pinmux_init(void); #endif diff --git a/arch/arm/mach-rmobile/include/mach/rmobile.h b/arch/arm/mach-rmobile/include/mach/rmobile.h index dc6f87631bc..53f9a80ecfe 100644 --- a/arch/arm/mach-rmobile/include/mach/rmobile.h +++ b/arch/arm/mach-rmobile/include/mach/rmobile.h @@ -2,9 +2,7 @@ #define __ASM_ARCH_RMOBILE_H #if defined(CONFIG_ARCH_RMOBILE) -#if defined(CONFIG_SH73A0) -#include <asm/arch/sh73a0.h> -#elif defined(CONFIG_R8A7740) +#if defined(CONFIG_R8A7740) #include <asm/arch/r8a7740.h> #elif defined(CONFIG_R8A7790) #include <asm/arch/r8a7790.h> @@ -25,7 +23,6 @@ #endif /* CONFIG_ARCH_RMOBILE */ /* PRR CPU IDs */ -#define RMOBILE_CPU_TYPE_SH73A0 0x37 #define RMOBILE_CPU_TYPE_R8A7740 0x40 #define RMOBILE_CPU_TYPE_R8A7790 0x45 #define RMOBILE_CPU_TYPE_R8A7791 0x47 diff --git a/arch/arm/mach-rmobile/include/mach/sh73a0-gpio.h b/arch/arm/mach-rmobile/include/mach/sh73a0-gpio.h deleted file mode 100644 index 398e2c10913..00000000000 --- a/arch/arm/mach-rmobile/include/mach/sh73a0-gpio.h +++ /dev/null @@ -1,553 +0,0 @@ -#ifndef __ASM_SH73A0_H__ -#define __ASM_SH73A0_H__ - -/* Pin Function Controller: - * GPIO_FN_xx - GPIO used to select pin function and MSEL switch - * GPIO_PORTxx - GPIO mapped to real I/O pin on CPU - */ -enum { - /* Hardware manual Table 25-1 (GPIO) */ - GPIO_PORT0, GPIO_PORT1, GPIO_PORT2, GPIO_PORT3, GPIO_PORT4, - GPIO_PORT5, GPIO_PORT6, GPIO_PORT7, GPIO_PORT8, GPIO_PORT9, - - GPIO_PORT10, GPIO_PORT11, GPIO_PORT12, GPIO_PORT13, GPIO_PORT14, - GPIO_PORT15, GPIO_PORT16, GPIO_PORT17, GPIO_PORT18, GPIO_PORT19, - - GPIO_PORT20, GPIO_PORT21, GPIO_PORT22, GPIO_PORT23, GPIO_PORT24, - GPIO_PORT25, GPIO_PORT26, GPIO_PORT27, GPIO_PORT28, GPIO_PORT29, - - GPIO_PORT30, GPIO_PORT31, GPIO_PORT32, GPIO_PORT33, GPIO_PORT34, - GPIO_PORT35, GPIO_PORT36, GPIO_PORT37, GPIO_PORT38, GPIO_PORT39, - - GPIO_PORT40, GPIO_PORT41, GPIO_PORT42, GPIO_PORT43, GPIO_PORT44, - GPIO_PORT45, GPIO_PORT46, GPIO_PORT47, GPIO_PORT48, GPIO_PORT49, - - GPIO_PORT50, GPIO_PORT51, GPIO_PORT52, GPIO_PORT53, GPIO_PORT54, - GPIO_PORT55, GPIO_PORT56, GPIO_PORT57, GPIO_PORT58, GPIO_PORT59, - - GPIO_PORT60, GPIO_PORT61, GPIO_PORT62, GPIO_PORT63, GPIO_PORT64, - GPIO_PORT65, GPIO_PORT66, GPIO_PORT67, GPIO_PORT68, GPIO_PORT69, - - GPIO_PORT70, GPIO_PORT71, GPIO_PORT72, GPIO_PORT73, GPIO_PORT74, - GPIO_PORT75, GPIO_PORT76, GPIO_PORT77, GPIO_PORT78, GPIO_PORT79, - - GPIO_PORT80, GPIO_PORT81, GPIO_PORT82, GPIO_PORT83, GPIO_PORT84, - GPIO_PORT85, GPIO_PORT86, GPIO_PORT87, GPIO_PORT88, GPIO_PORT89, - - GPIO_PORT90, GPIO_PORT91, GPIO_PORT92, GPIO_PORT93, GPIO_PORT94, - GPIO_PORT95, GPIO_PORT96, GPIO_PORT97, GPIO_PORT98, GPIO_PORT99, - - GPIO_PORT100, GPIO_PORT101, GPIO_PORT102, GPIO_PORT103, GPIO_PORT104, - GPIO_PORT105, GPIO_PORT106, GPIO_PORT107, GPIO_PORT108, GPIO_PORT109, - - GPIO_PORT110, GPIO_PORT111, GPIO_PORT112, GPIO_PORT113, GPIO_PORT114, - GPIO_PORT115, GPIO_PORT116, GPIO_PORT117, GPIO_PORT118, - - GPIO_PORT128, GPIO_PORT129, - - GPIO_PORT130, GPIO_PORT131, GPIO_PORT132, GPIO_PORT133, GPIO_PORT134, - GPIO_PORT135, GPIO_PORT136, GPIO_PORT137, GPIO_PORT138, GPIO_PORT139, - - GPIO_PORT140, GPIO_PORT141, GPIO_PORT142, GPIO_PORT143, GPIO_PORT144, - GPIO_PORT145, GPIO_PORT146, GPIO_PORT147, GPIO_PORT148, GPIO_PORT149, - - GPIO_PORT150, GPIO_PORT151, GPIO_PORT152, GPIO_PORT153, GPIO_PORT154, - GPIO_PORT155, GPIO_PORT156, GPIO_PORT157, GPIO_PORT158, GPIO_PORT159, - - GPIO_PORT160, GPIO_PORT161, GPIO_PORT162, GPIO_PORT163, GPIO_PORT164, - - GPIO_PORT192, GPIO_PORT193, GPIO_PORT194, - GPIO_PORT195, GPIO_PORT196, GPIO_PORT197, GPIO_PORT198, GPIO_PORT199, - - GPIO_PORT200, GPIO_PORT201, GPIO_PORT202, GPIO_PORT203, GPIO_PORT204, - GPIO_PORT205, GPIO_PORT206, GPIO_PORT207, GPIO_PORT208, GPIO_PORT209, - - GPIO_PORT210, GPIO_PORT211, GPIO_PORT212, GPIO_PORT213, GPIO_PORT214, - GPIO_PORT215, GPIO_PORT216, GPIO_PORT217, GPIO_PORT218, GPIO_PORT219, - - GPIO_PORT220, GPIO_PORT221, GPIO_PORT222, GPIO_PORT223, GPIO_PORT224, - GPIO_PORT225, GPIO_PORT226, GPIO_PORT227, GPIO_PORT228, GPIO_PORT229, - - GPIO_PORT230, GPIO_PORT231, GPIO_PORT232, GPIO_PORT233, GPIO_PORT234, - GPIO_PORT235, GPIO_PORT236, GPIO_PORT237, GPIO_PORT238, GPIO_PORT239, - - GPIO_PORT240, GPIO_PORT241, GPIO_PORT242, GPIO_PORT243, GPIO_PORT244, - GPIO_PORT245, GPIO_PORT246, GPIO_PORT247, GPIO_PORT248, GPIO_PORT249, - - GPIO_PORT250, GPIO_PORT251, GPIO_PORT252, GPIO_PORT253, GPIO_PORT254, - GPIO_PORT255, GPIO_PORT256, GPIO_PORT257, GPIO_PORT258, GPIO_PORT259, - - GPIO_PORT260, GPIO_PORT261, GPIO_PORT262, GPIO_PORT263, GPIO_PORT264, - GPIO_PORT265, GPIO_PORT266, GPIO_PORT267, GPIO_PORT268, GPIO_PORT269, - - GPIO_PORT270, GPIO_PORT271, GPIO_PORT272, GPIO_PORT273, GPIO_PORT274, - GPIO_PORT275, GPIO_PORT276, GPIO_PORT277, GPIO_PORT278, GPIO_PORT279, - - GPIO_PORT280, GPIO_PORT281, GPIO_PORT282, - - GPIO_PORT288, GPIO_PORT289, - - GPIO_PORT290, GPIO_PORT291, GPIO_PORT292, GPIO_PORT293, GPIO_PORT294, - GPIO_PORT295, GPIO_PORT296, GPIO_PORT297, GPIO_PORT298, GPIO_PORT299, - - GPIO_PORT300, GPIO_PORT301, GPIO_PORT302, GPIO_PORT303, GPIO_PORT304, - GPIO_PORT305, GPIO_PORT306, GPIO_PORT307, GPIO_PORT308, GPIO_PORT309, - - /* Table 25-1 (Function 0-7) */ - GPIO_FN_VBUS_0, - GPIO_FN_GPI0, - GPIO_FN_GPI1, - GPIO_FN_GPI2, - GPIO_FN_GPI3, - GPIO_FN_GPI4, - GPIO_FN_GPI5, - GPIO_FN_GPI6, - GPIO_FN_GPI7, - GPIO_FN_SCIFA7_RXD, - GPIO_FN_SCIFA7_CTS_, - GPIO_FN_GPO7, GPIO_FN_MFG0_OUT2, - GPIO_FN_GPO6, GPIO_FN_MFG1_OUT2, - GPIO_FN_GPO5, GPIO_FN_SCIFA0_SCK, GPIO_FN_FSICOSLDT3, \ - GPIO_FN_PORT16_VIO_CKOR, - GPIO_FN_SCIFA0_TXD, - GPIO_FN_SCIFA7_TXD, - GPIO_FN_SCIFA7_RTS_, GPIO_FN_PORT19_VIO_CKO2, - GPIO_FN_GPO0, - GPIO_FN_GPO1, - GPIO_FN_GPO2, GPIO_FN_STATUS0, - GPIO_FN_GPO3, GPIO_FN_STATUS1, - GPIO_FN_GPO4, GPIO_FN_STATUS2, - GPIO_FN_VINT, - GPIO_FN_TCKON, - GPIO_FN_XDVFS1, GPIO_FN_PORT27_I2C_SCL2, GPIO_FN_PORT27_I2C_SCL3, \ - GPIO_FN_MFG0_OUT1, GPIO_FN_PORT27_IROUT, - GPIO_FN_XDVFS2, GPIO_FN_PORT28_I2C_SDA2, GPIO_FN_PORT28_I2C_SDA3, \ - GPIO_FN_PORT28_TPU1TO1, - GPIO_FN_SIM_RST, GPIO_FN_PORT29_TPU1TO1, - GPIO_FN_SIM_CLK, GPIO_FN_PORT30_VIO_CKOR, - GPIO_FN_SIM_D, GPIO_FN_PORT31_IROUT, - GPIO_FN_SCIFA4_TXD, - GPIO_FN_SCIFA4_RXD, GPIO_FN_XWUP, - GPIO_FN_SCIFA4_RTS_, - GPIO_FN_SCIFA4_CTS_, - GPIO_FN_FSIBOBT, GPIO_FN_FSIBIBT, - GPIO_FN_FSIBOLR, GPIO_FN_FSIBILR, - GPIO_FN_FSIBOSLD, - GPIO_FN_FSIBISLD, - GPIO_FN_VACK, - GPIO_FN_XTAL1L, - GPIO_FN_SCIFA0_RTS_, GPIO_FN_FSICOSLDT2, - GPIO_FN_SCIFA0_RXD, - GPIO_FN_SCIFA0_CTS_, GPIO_FN_FSICOSLDT1, - GPIO_FN_FSICOBT, GPIO_FN_FSICIBT, GPIO_FN_FSIDOBT, GPIO_FN_FSIDIBT, - GPIO_FN_FSICOLR, GPIO_FN_FSICILR, GPIO_FN_FSIDOLR, GPIO_FN_FSIDILR, - GPIO_FN_FSICOSLD, GPIO_FN_PORT47_FSICSPDIF, - GPIO_FN_FSICISLD, GPIO_FN_FSIDISLD, - GPIO_FN_FSIACK, GPIO_FN_PORT49_IRDA_OUT, GPIO_FN_PORT49_IROUT, \ - GPIO_FN_FSIAOMC, - GPIO_FN_FSIAOLR, GPIO_FN_BBIF2_TSYNC2, GPIO_FN_TPU2TO2, GPIO_FN_FSIAILR, - - GPIO_FN_FSIAOBT, GPIO_FN_BBIF2_TSCK2, GPIO_FN_TPU2TO3, GPIO_FN_FSIAIBT, - GPIO_FN_FSIAOSLD, GPIO_FN_BBIF2_TXD2, - GPIO_FN_FSIASPDIF, GPIO_FN_PORT53_IRDA_IN, GPIO_FN_TPU3TO3, \ - GPIO_FN_FSIBSPDIF, GPIO_FN_PORT53_FSICSPDIF, - GPIO_FN_FSIBCK, GPIO_FN_PORT54_IRDA_FIRSEL, GPIO_FN_TPU3TO2, \ - GPIO_FN_FSIBOMC, GPIO_FN_FSICCK, GPIO_FN_FSICOMC, - GPIO_FN_FSIAISLD, GPIO_FN_TPU0TO0, - GPIO_FN_A0, GPIO_FN_BS_, - GPIO_FN_A12, GPIO_FN_PORT58_KEYOUT7, GPIO_FN_TPU4TO2, - GPIO_FN_A13, GPIO_FN_PORT59_KEYOUT6, GPIO_FN_TPU0TO1, - GPIO_FN_A14, GPIO_FN_KEYOUT5, - GPIO_FN_A15, GPIO_FN_KEYOUT4, - GPIO_FN_A16, GPIO_FN_KEYOUT3, GPIO_FN_MSIOF0_SS1, - GPIO_FN_A17, GPIO_FN_KEYOUT2, GPIO_FN_MSIOF0_TSYNC, - GPIO_FN_A18, GPIO_FN_KEYOUT1, GPIO_FN_MSIOF0_TSCK, - GPIO_FN_A19, GPIO_FN_KEYOUT0, GPIO_FN_MSIOF0_TXD, - GPIO_FN_A20, GPIO_FN_KEYIN0, GPIO_FN_MSIOF0_RSCK, - GPIO_FN_A21, GPIO_FN_KEYIN1, GPIO_FN_MSIOF0_RSYNC, - GPIO_FN_A22, GPIO_FN_KEYIN2, GPIO_FN_MSIOF0_MCK0, - GPIO_FN_A23, GPIO_FN_KEYIN3, GPIO_FN_MSIOF0_MCK1, - GPIO_FN_A24, GPIO_FN_KEYIN4, GPIO_FN_MSIOF0_RXD, - GPIO_FN_A25, GPIO_FN_KEYIN5, GPIO_FN_MSIOF0_SS2, - GPIO_FN_A26, GPIO_FN_KEYIN6, - GPIO_FN_KEYIN7, - GPIO_FN_D0_NAF0, - GPIO_FN_D1_NAF1, - GPIO_FN_D2_NAF2, - GPIO_FN_D3_NAF3, - GPIO_FN_D4_NAF4, - GPIO_FN_D5_NAF5, - GPIO_FN_D6_NAF6, - GPIO_FN_D7_NAF7, - GPIO_FN_D8_NAF8, - GPIO_FN_D9_NAF9, - GPIO_FN_D10_NAF10, - GPIO_FN_D11_NAF11, - GPIO_FN_D12_NAF12, - GPIO_FN_D13_NAF13, - GPIO_FN_D14_NAF14, - GPIO_FN_D15_NAF15, - GPIO_FN_CS4_, - GPIO_FN_CS5A_, GPIO_FN_PORT91_RDWR, - GPIO_FN_CS5B_, GPIO_FN_FCE1_, - GPIO_FN_CS6B_, GPIO_FN_DACK0, - GPIO_FN_FCE0_, GPIO_FN_CS6A_, - GPIO_FN_WAIT_, GPIO_FN_DREQ0, - GPIO_FN_RD__FSC, - GPIO_FN_WE0__FWE, GPIO_FN_RDWR_FWE, - GPIO_FN_WE1_, - GPIO_FN_FRB, - GPIO_FN_CKO, - GPIO_FN_NBRSTOUT_, - GPIO_FN_NBRST_, - GPIO_FN_BBIF2_TXD, - GPIO_FN_BBIF2_RXD, - GPIO_FN_BBIF2_SYNC, - GPIO_FN_BBIF2_SCK, - GPIO_FN_SCIFA3_CTS_, GPIO_FN_MFG3_IN2, - GPIO_FN_SCIFA3_RXD, GPIO_FN_MFG3_IN1, - GPIO_FN_BBIF1_SS2, GPIO_FN_SCIFA3_RTS_, GPIO_FN_MFG3_OUT1, - GPIO_FN_SCIFA3_TXD, - GPIO_FN_HSI_RX_DATA, GPIO_FN_BBIF1_RXD, - GPIO_FN_HSI_TX_WAKE, GPIO_FN_BBIF1_TSCK, - GPIO_FN_HSI_TX_DATA, GPIO_FN_BBIF1_TSYNC, - GPIO_FN_HSI_TX_READY, GPIO_FN_BBIF1_TXD, - GPIO_FN_HSI_RX_READY, GPIO_FN_BBIF1_RSCK, GPIO_FN_PORT115_I2C_SCL2, \ - GPIO_FN_PORT115_I2C_SCL3, - GPIO_FN_HSI_RX_WAKE, GPIO_FN_BBIF1_RSYNC, GPIO_FN_PORT116_I2C_SDA2, \ - GPIO_FN_PORT116_I2C_SDA3, - GPIO_FN_HSI_RX_FLAG, GPIO_FN_BBIF1_SS1, GPIO_FN_BBIF1_FLOW, - GPIO_FN_HSI_TX_FLAG, - GPIO_FN_VIO_VD, GPIO_FN_PORT128_LCD2VSYN, GPIO_FN_VIO2_VD, \ - GPIO_FN_LCD2D0, - - GPIO_FN_VIO_HD, GPIO_FN_PORT129_LCD2HSYN, GPIO_FN_PORT129_LCD2CS_, \ - GPIO_FN_VIO2_HD, GPIO_FN_LCD2D1, - GPIO_FN_VIO_D0, GPIO_FN_PORT130_MSIOF2_RXD, GPIO_FN_LCD2D10, - GPIO_FN_VIO_D1, GPIO_FN_PORT131_KEYOUT6, GPIO_FN_PORT131_MSIOF2_SS1, \ - GPIO_FN_PORT131_KEYOUT11, GPIO_FN_LCD2D11, - GPIO_FN_VIO_D2, GPIO_FN_PORT132_KEYOUT7, GPIO_FN_PORT132_MSIOF2_SS2, \ - GPIO_FN_PORT132_KEYOUT10, GPIO_FN_LCD2D12, - GPIO_FN_VIO_D3, GPIO_FN_MSIOF2_TSYNC, GPIO_FN_LCD2D13, - GPIO_FN_VIO_D4, GPIO_FN_MSIOF2_TXD, GPIO_FN_LCD2D14, - GPIO_FN_VIO_D5, GPIO_FN_MSIOF2_TSCK, GPIO_FN_LCD2D15, - GPIO_FN_VIO_D6, GPIO_FN_PORT136_KEYOUT8, GPIO_FN_LCD2D16, - GPIO_FN_VIO_D7, GPIO_FN_PORT137_KEYOUT9, GPIO_FN_LCD2D17, - GPIO_FN_VIO_D8, GPIO_FN_PORT138_KEYOUT8, GPIO_FN_VIO2_D0, \ - GPIO_FN_LCD2D6, - GPIO_FN_VIO_D9, GPIO_FN_PORT139_KEYOUT9, GPIO_FN_VIO2_D1, \ - GPIO_FN_LCD2D7, - GPIO_FN_VIO_D10, GPIO_FN_TPU0TO2, GPIO_FN_VIO2_D2, GPIO_FN_LCD2D8, - GPIO_FN_VIO_D11, GPIO_FN_TPU0TO3, GPIO_FN_VIO2_D3, GPIO_FN_LCD2D9, - GPIO_FN_VIO_D12, GPIO_FN_PORT142_KEYOUT10, GPIO_FN_VIO2_D4, \ - GPIO_FN_LCD2D2, - GPIO_FN_VIO_D13, GPIO_FN_PORT143_KEYOUT11, GPIO_FN_PORT143_KEYOUT6, \ - GPIO_FN_VIO2_D5, GPIO_FN_LCD2D3, - GPIO_FN_VIO_D14, GPIO_FN_PORT144_KEYOUT7, GPIO_FN_VIO2_D6, \ - GPIO_FN_LCD2D4, - GPIO_FN_VIO_D15, GPIO_FN_TPU1TO3, GPIO_FN_PORT145_LCD2DISP, \ - GPIO_FN_PORT145_LCD2RS, GPIO_FN_VIO2_D7, GPIO_FN_LCD2D5, - GPIO_FN_VIO_CLK, GPIO_FN_LCD2DCK, GPIO_FN_PORT146_LCD2WR_, \ - GPIO_FN_VIO2_CLK, GPIO_FN_LCD2D18, - GPIO_FN_VIO_FIELD, GPIO_FN_LCD2RD_, GPIO_FN_VIO2_FIELD, GPIO_FN_LCD2D19, - GPIO_FN_VIO_CKO, - GPIO_FN_A27, GPIO_FN_PORT149_RDWR, GPIO_FN_MFG0_IN1, \ - GPIO_FN_PORT149_KEYOUT9, - GPIO_FN_MFG0_IN2, - GPIO_FN_TS_SPSYNC3, GPIO_FN_MSIOF2_RSCK, - GPIO_FN_TS_SDAT3, GPIO_FN_MSIOF2_RSYNC, - GPIO_FN_TPU1TO2, GPIO_FN_TS_SDEN3, GPIO_FN_PORT153_MSIOF2_SS1, - GPIO_FN_SCIFA2_TXD1, GPIO_FN_MSIOF2_MCK0, - GPIO_FN_SCIFA2_RXD1, GPIO_FN_MSIOF2_MCK1, - GPIO_FN_SCIFA2_RTS1_, GPIO_FN_PORT156_MSIOF2_SS2, - GPIO_FN_SCIFA2_CTS1_, GPIO_FN_PORT157_MSIOF2_RXD, - GPIO_FN_DINT_, GPIO_FN_SCIFA2_SCK1, GPIO_FN_TS_SCK3, - GPIO_FN_PORT159_SCIFB_SCK, GPIO_FN_PORT159_SCIFA5_SCK, GPIO_FN_NMI, - GPIO_FN_PORT160_SCIFB_TXD, GPIO_FN_PORT160_SCIFA5_TXD, - GPIO_FN_PORT161_SCIFB_CTS_, GPIO_FN_PORT161_SCIFA5_CTS_, - GPIO_FN_PORT162_SCIFB_RXD, GPIO_FN_PORT162_SCIFA5_RXD, - GPIO_FN_PORT163_SCIFB_RTS_, GPIO_FN_PORT163_SCIFA5_RTS_, \ - GPIO_FN_TPU3TO0, - GPIO_FN_LCDD0, - GPIO_FN_LCDD1, GPIO_FN_PORT193_SCIFA5_CTS_, GPIO_FN_BBIF2_TSYNC1, - GPIO_FN_LCDD2, GPIO_FN_PORT194_SCIFA5_RTS_, GPIO_FN_BBIF2_TSCK1, - GPIO_FN_LCDD3, GPIO_FN_PORT195_SCIFA5_RXD, GPIO_FN_BBIF2_TXD1, - GPIO_FN_LCDD4, GPIO_FN_PORT196_SCIFA5_TXD, - GPIO_FN_LCDD5, GPIO_FN_PORT197_SCIFA5_SCK, GPIO_FN_MFG2_OUT2, \ - GPIO_FN_TPU2TO1, - GPIO_FN_LCDD6, - GPIO_FN_LCDD7, GPIO_FN_TPU4TO1, GPIO_FN_MFG4_OUT2, - GPIO_FN_LCDD8, GPIO_FN_D16, - GPIO_FN_LCDD9, GPIO_FN_D17, - GPIO_FN_LCDD10, GPIO_FN_D18, - GPIO_FN_LCDD11, GPIO_FN_D19, - GPIO_FN_LCDD12, GPIO_FN_D20, - GPIO_FN_LCDD13, GPIO_FN_D21, - GPIO_FN_LCDD14, GPIO_FN_D22, - GPIO_FN_LCDD15, GPIO_FN_PORT207_MSIOF0L_SS1, GPIO_FN_D23, - GPIO_FN_LCDD16, GPIO_FN_PORT208_MSIOF0L_SS2, GPIO_FN_D24, - GPIO_FN_LCDD17, GPIO_FN_D25, - GPIO_FN_LCDD18, GPIO_FN_DREQ2, GPIO_FN_PORT210_MSIOF0L_SS1, GPIO_FN_D26, - GPIO_FN_LCDD19, GPIO_FN_PORT211_MSIOF0L_SS2, GPIO_FN_D27, - GPIO_FN_LCDD20, GPIO_FN_TS_SPSYNC1, GPIO_FN_MSIOF0L_MCK0, GPIO_FN_D28, - GPIO_FN_LCDD21, GPIO_FN_TS_SDAT1, GPIO_FN_MSIOF0L_MCK1, GPIO_FN_D29, - GPIO_FN_LCDD22, GPIO_FN_TS_SDEN1, GPIO_FN_MSIOF0L_RSCK, GPIO_FN_D30, - GPIO_FN_LCDD23, GPIO_FN_TS_SCK1, GPIO_FN_MSIOF0L_RSYNC, GPIO_FN_D31, - GPIO_FN_LCDDCK, GPIO_FN_LCDWR_, - GPIO_FN_LCDRD_, GPIO_FN_DACK2, GPIO_FN_PORT217_LCD2RS, \ - GPIO_FN_MSIOF0L_TSYNC, GPIO_FN_VIO2_FIELD3, GPIO_FN_PORT217_LCD2DISP, - GPIO_FN_LCDHSYN, GPIO_FN_LCDCS_, GPIO_FN_LCDCS2_, GPIO_FN_DACK3, \ - GPIO_FN_PORT218_VIO_CKOR, - GPIO_FN_LCDDISP, GPIO_FN_LCDRS, GPIO_FN_PORT219_LCD2WR_, \ - GPIO_FN_DREQ3, GPIO_FN_MSIOF0L_TSCK, GPIO_FN_VIO2_CLK3, \ - GPIO_FN_LCD2DCK_2, - GPIO_FN_LCDVSYN, GPIO_FN_LCDVSYN2, - GPIO_FN_LCDLCLK, GPIO_FN_DREQ1, GPIO_FN_PORT221_LCD2CS_, \ - GPIO_FN_PWEN, GPIO_FN_MSIOF0L_RXD, GPIO_FN_VIO2_HD3, \ - GPIO_FN_PORT221_LCD2HSYN, - GPIO_FN_LCDDON, GPIO_FN_LCDDON2, GPIO_FN_DACK1, GPIO_FN_OVCN, \ - GPIO_FN_MSIOF0L_TXD, GPIO_FN_VIO2_VD3, GPIO_FN_PORT222_LCD2VSYN, - - GPIO_FN_SCIFA1_TXD, GPIO_FN_OVCN2, - GPIO_FN_EXTLP, GPIO_FN_SCIFA1_SCK, GPIO_FN_PORT226_VIO_CKO2, - GPIO_FN_SCIFA1_RTS_, GPIO_FN_IDIN, - GPIO_FN_SCIFA1_RXD, - GPIO_FN_SCIFA1_CTS_, GPIO_FN_MFG1_IN1, - GPIO_FN_MSIOF1_TXD, GPIO_FN_SCIFA2_TXD2, - GPIO_FN_MSIOF1_TSYNC, GPIO_FN_SCIFA2_CTS2_, - GPIO_FN_MSIOF1_TSCK, GPIO_FN_SCIFA2_SCK2, - GPIO_FN_MSIOF1_RXD, GPIO_FN_SCIFA2_RXD2, - GPIO_FN_MSIOF1_RSCK, GPIO_FN_SCIFA2_RTS2_, GPIO_FN_VIO2_CLK2, \ - GPIO_FN_LCD2D20, - GPIO_FN_MSIOF1_RSYNC, GPIO_FN_MFG1_IN2, GPIO_FN_VIO2_VD2, \ - GPIO_FN_LCD2D21, - GPIO_FN_MSIOF1_MCK0, GPIO_FN_PORT236_I2C_SDA2, - GPIO_FN_MSIOF1_MCK1, GPIO_FN_PORT237_I2C_SCL2, - GPIO_FN_MSIOF1_SS1, GPIO_FN_VIO2_FIELD2, GPIO_FN_LCD2D22, - GPIO_FN_MSIOF1_SS2, GPIO_FN_VIO2_HD2, GPIO_FN_LCD2D23, - GPIO_FN_SCIFA6_TXD, - GPIO_FN_PORT241_IRDA_OUT, GPIO_FN_PORT241_IROUT, GPIO_FN_MFG4_OUT1, \ - GPIO_FN_TPU4TO0, - GPIO_FN_PORT242_IRDA_IN, GPIO_FN_MFG4_IN2, - GPIO_FN_PORT243_IRDA_FIRSEL, GPIO_FN_PORT243_VIO_CKO2, - GPIO_FN_PORT244_SCIFA5_CTS_, GPIO_FN_MFG2_IN1, \ - GPIO_FN_PORT244_SCIFB_CTS_, GPIO_FN_MSIOF2R_RXD, - GPIO_FN_PORT245_SCIFA5_RTS_, GPIO_FN_MFG2_IN2, \ - GPIO_FN_PORT245_SCIFB_RTS_, GPIO_FN_MSIOF2R_TXD, - GPIO_FN_PORT246_SCIFA5_RXD, GPIO_FN_MFG1_OUT1, \ - GPIO_FN_PORT246_SCIFB_RXD, GPIO_FN_TPU1TO0, - GPIO_FN_PORT247_SCIFA5_TXD, GPIO_FN_MFG3_OUT2, \ - GPIO_FN_PORT247_SCIFB_TXD, GPIO_FN_TPU3TO1, - GPIO_FN_PORT248_SCIFA5_SCK, GPIO_FN_MFG2_OUT1, \ - GPIO_FN_PORT248_SCIFB_SCK, GPIO_FN_TPU2TO0, \ - GPIO_FN_PORT248_I2C_SCL3, GPIO_FN_MSIOF2R_TSCK, - GPIO_FN_PORT249_IROUT, GPIO_FN_MFG4_IN1, \ - GPIO_FN_PORT249_I2C_SDA3, GPIO_FN_MSIOF2R_TSYNC, - GPIO_FN_SDHICLK0, - GPIO_FN_SDHICD0, - GPIO_FN_SDHID0_0, - GPIO_FN_SDHID0_1, - GPIO_FN_SDHID0_2, - GPIO_FN_SDHID0_3, - GPIO_FN_SDHICMD0, - GPIO_FN_SDHIWP0, - GPIO_FN_SDHICLK1, - GPIO_FN_SDHID1_0, GPIO_FN_TS_SPSYNC2, - GPIO_FN_SDHID1_1, GPIO_FN_TS_SDAT2, - GPIO_FN_SDHID1_2, GPIO_FN_TS_SDEN2, - GPIO_FN_SDHID1_3, GPIO_FN_TS_SCK2, - GPIO_FN_SDHICMD1, - GPIO_FN_SDHICLK2, - GPIO_FN_SDHID2_0, GPIO_FN_TS_SPSYNC4, - GPIO_FN_SDHID2_1, GPIO_FN_TS_SDAT4, - GPIO_FN_SDHID2_2, GPIO_FN_TS_SDEN4, - GPIO_FN_SDHID2_3, GPIO_FN_TS_SCK4, - GPIO_FN_SDHICMD2, - GPIO_FN_MMCCLK0, - GPIO_FN_MMCD0_0, - GPIO_FN_MMCD0_1, - GPIO_FN_MMCD0_2, - GPIO_FN_MMCD0_3, - GPIO_FN_MMCD0_4, GPIO_FN_TS_SPSYNC5, - GPIO_FN_MMCD0_5, GPIO_FN_TS_SDAT5, - GPIO_FN_MMCD0_6, GPIO_FN_TS_SDEN5, - GPIO_FN_MMCD0_7, GPIO_FN_TS_SCK5, - GPIO_FN_MMCCMD0, - GPIO_FN_RESETOUTS_, GPIO_FN_EXTAL2OUT, - GPIO_FN_MCP_WAIT__MCP_FRB, - GPIO_FN_MCP_CKO, GPIO_FN_MMCCLK1, - GPIO_FN_MCP_D15_MCP_NAF15, - GPIO_FN_MCP_D14_MCP_NAF14, - GPIO_FN_MCP_D13_MCP_NAF13, - GPIO_FN_MCP_D12_MCP_NAF12, - GPIO_FN_MCP_D11_MCP_NAF11, - GPIO_FN_MCP_D10_MCP_NAF10, - GPIO_FN_MCP_D9_MCP_NAF9, - GPIO_FN_MCP_D8_MCP_NAF8, GPIO_FN_MMCCMD1, - GPIO_FN_MCP_D7_MCP_NAF7, GPIO_FN_MMCD1_7, - - GPIO_FN_MCP_D6_MCP_NAF6, GPIO_FN_MMCD1_6, - GPIO_FN_MCP_D5_MCP_NAF5, GPIO_FN_MMCD1_5, - GPIO_FN_MCP_D4_MCP_NAF4, GPIO_FN_MMCD1_4, - GPIO_FN_MCP_D3_MCP_NAF3, GPIO_FN_MMCD1_3, - GPIO_FN_MCP_D2_MCP_NAF2, GPIO_FN_MMCD1_2, - GPIO_FN_MCP_D1_MCP_NAF1, GPIO_FN_MMCD1_1, - GPIO_FN_MCP_D0_MCP_NAF0, GPIO_FN_MMCD1_0, - GPIO_FN_MCP_NBRSTOUT_, - GPIO_FN_MCP_WE0__MCP_FWE, GPIO_FN_MCP_RDWR_MCP_FWE, - - /* MSEL2 special case */ - GPIO_FN_TSIF2_TS_XX1, - GPIO_FN_TSIF2_TS_XX2, - GPIO_FN_TSIF2_TS_XX3, - GPIO_FN_TSIF2_TS_XX4, - GPIO_FN_TSIF2_TS_XX5, - GPIO_FN_TSIF1_TS_XX1, - GPIO_FN_TSIF1_TS_XX2, - GPIO_FN_TSIF1_TS_XX3, - GPIO_FN_TSIF1_TS_XX4, - GPIO_FN_TSIF1_TS_XX5, - GPIO_FN_TSIF0_TS_XX1, - GPIO_FN_TSIF0_TS_XX2, - GPIO_FN_TSIF0_TS_XX3, - GPIO_FN_TSIF0_TS_XX4, - GPIO_FN_TSIF0_TS_XX5, - GPIO_FN_MST1_TS_XX1, - GPIO_FN_MST1_TS_XX2, - GPIO_FN_MST1_TS_XX3, - GPIO_FN_MST1_TS_XX4, - GPIO_FN_MST1_TS_XX5, - GPIO_FN_MST0_TS_XX1, - GPIO_FN_MST0_TS_XX2, - GPIO_FN_MST0_TS_XX3, - GPIO_FN_MST0_TS_XX4, - GPIO_FN_MST0_TS_XX5, - - /* MSEL3 special cases */ - GPIO_FN_SDHI0_VCCQ_MC0_ON, - GPIO_FN_SDHI0_VCCQ_MC0_OFF, - GPIO_FN_DEBUG_MON_VIO, - GPIO_FN_DEBUG_MON_LCDD, - GPIO_FN_LCDC_LCDC0, - GPIO_FN_LCDC_LCDC1, - - /* MSEL4 special cases */ - GPIO_FN_IRQ9_MEM_INT, - GPIO_FN_IRQ9_MCP_INT, - GPIO_FN_A11, - GPIO_FN_KEYOUT8, - GPIO_FN_TPU4TO3, - GPIO_FN_RESETA_N_PU_ON, - GPIO_FN_RESETA_N_PU_OFF, - GPIO_FN_EDBGREQ_PD, - GPIO_FN_EDBGREQ_PU, - - /* Functions with pull-ups */ - GPIO_FN_KEYIN0_PU, - GPIO_FN_KEYIN1_PU, - GPIO_FN_KEYIN2_PU, - GPIO_FN_KEYIN3_PU, - GPIO_FN_KEYIN4_PU, - GPIO_FN_KEYIN5_PU, - GPIO_FN_KEYIN6_PU, - GPIO_FN_KEYIN7_PU, - GPIO_FN_SDHICD0_PU, - GPIO_FN_SDHID0_0_PU, - GPIO_FN_SDHID0_1_PU, - GPIO_FN_SDHID0_2_PU, - GPIO_FN_SDHID0_3_PU, - GPIO_FN_SDHICMD0_PU, - GPIO_FN_SDHIWP0_PU, - GPIO_FN_SDHID1_0_PU, - GPIO_FN_SDHID1_1_PU, - GPIO_FN_SDHID1_2_PU, - GPIO_FN_SDHID1_3_PU, - GPIO_FN_SDHICMD1_PU, - GPIO_FN_SDHID2_0_PU, - GPIO_FN_SDHID2_1_PU, - GPIO_FN_SDHID2_2_PU, - GPIO_FN_SDHID2_3_PU, - GPIO_FN_SDHICMD2_PU, - GPIO_FN_MMCCMD0_PU, - GPIO_FN_MMCCMD1_PU, - GPIO_FN_MMCD0_0_PU, - GPIO_FN_MMCD0_1_PU, - GPIO_FN_MMCD0_2_PU, - GPIO_FN_MMCD0_3_PU, - GPIO_FN_MMCD0_4_PU, - GPIO_FN_MMCD0_5_PU, - GPIO_FN_MMCD0_6_PU, - GPIO_FN_MMCD0_7_PU, - GPIO_FN_FSIACK_PU, - GPIO_FN_FSIAILR_PU, - GPIO_FN_FSIAIBT_PU, - GPIO_FN_FSIAISLD_PU, - - /* end of GPIO */ - GPIO_NR, -}; - -/* DMA slave IDs */ -enum { - SHDMA_SLAVE_INVALID, - SHDMA_SLAVE_SCIF0_TX, - SHDMA_SLAVE_SCIF0_RX, - SHDMA_SLAVE_SCIF1_TX, - SHDMA_SLAVE_SCIF1_RX, - SHDMA_SLAVE_SCIF2_TX, - SHDMA_SLAVE_SCIF2_RX, - SHDMA_SLAVE_SCIF3_TX, - SHDMA_SLAVE_SCIF3_RX, - SHDMA_SLAVE_SCIF4_TX, - SHDMA_SLAVE_SCIF4_RX, - SHDMA_SLAVE_SCIF5_TX, - SHDMA_SLAVE_SCIF5_RX, - SHDMA_SLAVE_SCIF6_TX, - SHDMA_SLAVE_SCIF6_RX, - SHDMA_SLAVE_SCIF7_TX, - SHDMA_SLAVE_SCIF7_RX, - SHDMA_SLAVE_SCIF8_TX, - SHDMA_SLAVE_SCIF8_RX, - SHDMA_SLAVE_SDHI0_TX, - SHDMA_SLAVE_SDHI0_RX, - SHDMA_SLAVE_SDHI1_TX, - SHDMA_SLAVE_SDHI1_RX, - SHDMA_SLAVE_SDHI2_TX, - SHDMA_SLAVE_SDHI2_RX, - SHDMA_SLAVE_MMCIF_TX, - SHDMA_SLAVE_MMCIF_RX, -}; - -/* - * SH73A0 IRQ LOCATION TABLE - * - * 416 ----------------------------------------- - * IRQ0-IRQ15 - * 431 ----------------------------------------- - * ... - * 448 ----------------------------------------- - * sh73a0-intcs - * sh73a0-intca-irq-pins - * 680 ----------------------------------------- - * ... - * 700 ----------------------------------------- - * sh73a0-pint0 - * 731 ----------------------------------------- - * 732 ----------------------------------------- - * sh73a0-pint1 - * 739 ----------------------------------------- - * ... - * 800 ----------------------------------------- - * IRQ16-IRQ31 - * 815 ----------------------------------------- - * ... - * 928 ----------------------------------------- - * sh73a0-intca-irq-pins - * 943 ----------------------------------------- - */ - -/* PINT interrupts are located at Linux IRQ 700 and up */ -#define SH73A0_PINT0_IRQ(irq) ((irq) + 700) -#define SH73A0_PINT1_IRQ(irq) ((irq) + 732) - -#endif /* __ASM_SH73A0_H__ */ diff --git a/arch/arm/mach-rmobile/include/mach/sh73a0.h b/arch/arm/mach-rmobile/include/mach/sh73a0.h deleted file mode 100644 index bdbb4086421..00000000000 --- a/arch/arm/mach-rmobile/include/mach/sh73a0.h +++ /dev/null @@ -1,289 +0,0 @@ -#ifndef __ASM_ARCH_RMOBILE_SH73A0_H -#define __ASM_ARCH_RMOBILE_SH73A0_H - -/* Global Timer */ -#define GLOBAL_TIMER_BASE_ADDR (0xF0000200) -#define MERAM_BASE (0xE5580000) - -/* GIC */ -#define GIC_BASE (0xF0000100) -#define ICCICR GIC_BASE - -/* Secure control register */ -#define LIFEC_SEC_SRC (0xE6110008) - -/* RWDT */ -#define RWDT_BASE (0xE6020000) - -/* HPB Semaphore Control Registers */ -#define HPB_BASE (0xE6001010) - -/* Bus Semaphore Control Registers */ -#define HPBSCR_BASE (0xE6001600) - -/* SBSC1 */ -#define SBSC1_BASE (0xFE400000) -#define SDMRA1A (SBSC1_BASE + 0x100000) -#define SDMRA2A (SBSC1_BASE + 0x1C0000) -#define SDMRA3A (SBSC1_BASE + 0x104000) - -/* SBSC2 */ -#define SBSC2_BASE (0xFB400000) -#define SDMRA1B (SBSC2_BASE + 0x100000) -#define SDMRA2B (SBSC2_BASE + 0x1C0000) -#define SDMRA3B (SBSC2_BASE + 0x104000) - -/* CPG */ -#define CPG_BASE (0xE6150000) -#define CPG_SRCR_BASE (CPG_BASE + 0x80A0) -#define WUPCR (CPG_BASE + 0x1010) -#define SRESCR (CPG_BASE + 0x1018) -#define PCLKCR (CPG_BASE + 0x1020) - -/* SYSC */ -#define SYSC_BASE (0xE6180000) -#define RESCNT2 (SYSC_BASE + 0x8020) - -/* BSC */ -#define BSC_BASE (0xFEC10000) - -/* SCIF */ -#define SCIF0_BASE (0xE6C40000) -#define SCIF1_BASE (0xE6C50000) -#define SCIF2_BASE (0xE6C60000) -#define SCIF3_BASE (0xE6C70000) -#define SCIF4_BASE (0xE6C80000) -#define SCIF5_BASE (0xE6CB0000) -#define SCIF6_BASE (0xE6CC0000) -#define SCIF7_BASE (0xE6CD0000) - -#ifndef __ASSEMBLY__ -#include <asm/types.h> - -/* RWDT */ -struct sh73a0_rwdt { - u16 rwtcnt0; /* 0x00 */ - u16 dummy0; /* 0x02 */ - u16 rwtcsra0; /* 0x04 */ - u16 dummy1; /* 0x06 */ - u16 rwtcsrb0; /* 0x08 */ -}; - -/* HPB Semaphore Control Registers */ -struct sh73a0_hpb { - u32 hpbctrl0; - u32 hpbctrl1; - u32 hpbctrl2; - u32 cccr; - u32 dummy0; /* 0x20 */ - u32 hpbctrl4; - u32 hpbctrl5; - u32 dummy1; /* 0x2C */ - u32 hpbctrl6; -}; - -/* Bus Semaphore Control Registers */ -struct sh73a0_hpb_bscr { - u32 mpsrc; /* 0x00 */ - u32 mpacctl; /* 0x04 */ - u32 dummy0[6]; - u32 smgpiosrc; /* 0x20 */ - u32 smgpioerr; - u32 smgpiotime; - u32 smgpiocnt; - u32 dummy1[4]; /* 0x30 .. 0x3C */ - u32 smcmt2src; - u32 smcmt2err; - u32 smcmt2time; - u32 smcmt2cnt; - u32 smcpgsrc; - u32 smcpgerr; - u32 smcpgtime; - u32 smcpgcnt; - u32 dummy2[4]; /* 0x60 - 0x6C */ - u32 smsyscsrc; - u32 smsyscerr; - u32 smsysctime; - u32 smsysccnt; -}; - -/* SBSC */ -struct sh73a0_sbsc { - u32 dummy0[2]; /* 0x00, 0x04 */ - u32 sdcr0; - u32 sdcr1; - u32 sdpcr; - u32 dummy1; /* 0x14 */ - u32 sdcr0s; - u32 sdcr1s; - u32 rtcsr; - u32 dummy2; /* 0x24 */ - u32 rtcor; - u32 rtcorh; - u32 rtcors; - u32 rtcorsh; - u32 dummy3[2]; /* 0x38, 0x3C */ - u32 sdwcrc0; - u32 sdwcrc1; - u32 sdwcr00; - u32 sdwcr01; - u32 sdwcr10; - u32 sdwcr11; - u32 sdpdcr0; - u32 dummy4; /* 0x5C */ - u32 sdwcr2; - u32 sdwcrc2; - u32 zqccr; - u32 dummy5[6]; /* 0x6C .. 0x80 */ - u32 sdmracr0; - u32 dummy6; /* 0x88 */ - u32 sdmrtmpcr; - u32 dummy7; /* 0x90 */ - u32 sdmrtmpmsk; - u32 dummy8; /* 0x98 */ - u32 sdgencnt; - u32 dphycnt0; - u32 dphycnt1; - u32 dphycnt2; - u32 dummy9[2]; /* 0xAC .. 0xB0 */ - u32 sddrvcr0; - u32 dummy10[14]; /* 0xB8 .. 0xEC */ - u32 dptdivcr0; - u32 dptdivcr1; - u32 dptdivcr2; - u32 dummy11; /* 0xFC */ - u32 sdptcr0; - u32 sdptcr1; - u32 sdptcr2; - u32 sdptcr3; /* 0x10C */ - u32 dummy12[145]; /* 0x110 .. 0x350 */ - u32 dllcnt0; /* 0x354 */ - u32 sbscmon0; -}; - -/* CPG */ -struct sh73a0_sbsc_cpg { - u32 frqcra; /* 0x00 */ - u32 frqcrb; - u32 vclkcr1; - u32 vclkcr2; - u32 zbckcr; - u32 flckcr; - u32 fsiackcr; - u32 vclkcr3; - u32 rtstbcr; - u32 systbcr; - u32 pll1cr; - u32 pll2cr; - u32 mstpsr0; - u32 dummy0; /* 0x34 */ - u32 mstpsr1; - u32 mstpsr5; - u32 mstpsr2; - u32 dummy1; /* 0x44 */ - u32 mstpsr3; - u32 mstpsr4; - u32 dummy2; /* 0x50 */ - u32 astat; - u32 dvfscr0; - u32 dvfscr1; - u32 dsitckcr; - u32 dsi0pckcr; - u32 dsi1pckcr; - u32 dsi0phycr; - u32 dsi1phycr; - u32 sd0ckcr; - u32 sd1ckcr; - u32 sd2ckcr; - u32 subckcr; - u32 spuackcr; - u32 msuckcr; - u32 hsickcr; - u32 fsibckcr; - u32 spuvckcr; - u32 mfck1cr; - u32 mfck2cr; - u32 dummy3[8]; /* 0xA0 .. 0xBC */ - u32 ckscr; - u32 dummy4; /* 0xC4 */ - u32 pll1stpcr; - u32 mpmode; - u32 pllecr; - u32 dummy5; /* 0xD4 */ - u32 pll0cr; - u32 pll3cr; - u32 dummy6; /* 0xE0 */ - u32 frqcrd; - u32 dummyi7; /* 0xE8 */ - u32 vrefcr; - u32 pll0stpcr; - u32 dummy8; /* 0xF4 */ - u32 pll2stpcr; - u32 pll3stpcr; - u32 dummy9[4]; /* 0x100 .. 0x10c */ - u32 rmstpcr0; - u32 rmstpcr1; - u32 rmstpcr2; - u32 rmstpcr3; - u32 rmstpcr4; - u32 rmstpcr5; - u32 dummy10[2]; /* 0x128 .. 0x12c */ - u32 smstpcr0; - u32 smstpcr1; - u32 smstpcr2; - u32 smstpcr3; - u32 smstpcr4; - u32 smstpcr5; - u32 dummy11[2]; /* 0x148 .. 0x14c */ - u32 cpgxxcs4; - u32 dummy12[7]; /* 0x154 .. 0x16c */ - u32 dvfscr2; - u32 dvfscr3; - u32 dvfscr4; - u32 dvfscr5; /* 0x17C */ -}; - -/* CPG SRCR part OK */ -struct sh73a0_sbsc_cpg_srcr { - u32 srcr0; - u32 dummy0; /* 0xA4 */ - u32 srcr1; - u32 dummy1; /* 0xAC */ - u32 srcr2; - u32 dummy2; /* 0xB4 */ - u32 srcr3; - u32 srcr4; - u32 dummy3; /* 0xC0 */ - u32 srcr5; -}; - -/* BSC */ -struct sh73a0_bsc { - u32 cmncr; - u32 cs0bcr; - u32 cs2bcr; - u32 dummy0; /* 0x0C */ - u32 cs4bcr; - u32 cs5abcr; - u32 cs5bbcr; - u32 cs6abcr; - u32 cs6bbcr; - u32 cs0wcr; - u32 cs2wcr; - u32 dummy1; /* 0x2C */ - u32 cs4wcr; - u32 cs5awcr; - u32 cs5bwcr; - u32 cs6awcr; - u32 cs6bwcr; - u32 rbwtcnt; - u32 busycr; - u32 dummy2; /* 0x5c */ - u32 cs7abcr; - u32 cs7awcr; - u32 dummy3[2]; /* 0x68, 0x6C */ - u32 bromtimcr; -}; -#endif /* __ASSEMBLY__ */ - -#endif /* __ASM_ARCH_RMOBILE_SH73A0_H */ diff --git a/arch/arm/mach-rmobile/pfc-sh73a0.c b/arch/arm/mach-rmobile/pfc-sh73a0.c deleted file mode 100644 index 55dab7c1389..00000000000 --- a/arch/arm/mach-rmobile/pfc-sh73a0.c +++ /dev/null @@ -1,2807 +0,0 @@ -/* - * sh73a0 processor support - PFC hardware block - * - * Copyright (C) 2010 Renesas Solutions Corp. - * Copyright (C) 2010 NISHIMOTO Hiroki - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; version 2 of the - * License. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA - */ - -#include <common.h> -#include <sh_pfc.h> -#include <asm/arch/sh73a0-gpio.h> - -#define CPU_ALL_PORT(fn, pfx, sfx) \ - PORT_10(fn, pfx, sfx), PORT_10(fn, pfx##1, sfx), \ - PORT_10(fn, pfx##2, sfx), PORT_10(fn, pfx##3, sfx), \ - PORT_10(fn, pfx##4, sfx), PORT_10(fn, pfx##5, sfx), \ - PORT_10(fn, pfx##6, sfx), PORT_10(fn, pfx##7, sfx), \ - PORT_10(fn, pfx##8, sfx), PORT_10(fn, pfx##9, sfx), \ - PORT_10(fn, pfx##10, sfx), \ - PORT_1(fn, pfx##110, sfx), PORT_1(fn, pfx##111, sfx), \ - PORT_1(fn, pfx##112, sfx), PORT_1(fn, pfx##113, sfx), \ - PORT_1(fn, pfx##114, sfx), PORT_1(fn, pfx##115, sfx), \ - PORT_1(fn, pfx##116, sfx), PORT_1(fn, pfx##117, sfx), \ - PORT_1(fn, pfx##118, sfx), \ - PORT_1(fn, pfx##128, sfx), PORT_1(fn, pfx##129, sfx), \ - PORT_10(fn, pfx##13, sfx), PORT_10(fn, pfx##14, sfx), \ - PORT_10(fn, pfx##15, sfx), \ - PORT_1(fn, pfx##160, sfx), PORT_1(fn, pfx##161, sfx), \ - PORT_1(fn, pfx##162, sfx), PORT_1(fn, pfx##163, sfx), \ - PORT_1(fn, pfx##164, sfx), \ - PORT_1(fn, pfx##192, sfx), PORT_1(fn, pfx##193, sfx), \ - PORT_1(fn, pfx##194, sfx), PORT_1(fn, pfx##195, sfx), \ - PORT_1(fn, pfx##196, sfx), PORT_1(fn, pfx##197, sfx), \ - PORT_1(fn, pfx##198, sfx), PORT_1(fn, pfx##199, sfx), \ - PORT_10(fn, pfx##20, sfx), PORT_10(fn, pfx##21, sfx), \ - PORT_10(fn, pfx##22, sfx), PORT_10(fn, pfx##23, sfx), \ - PORT_10(fn, pfx##24, sfx), PORT_10(fn, pfx##25, sfx), \ - PORT_10(fn, pfx##26, sfx), PORT_10(fn, pfx##27, sfx), \ - PORT_1(fn, pfx##280, sfx), PORT_1(fn, pfx##281, sfx), \ - PORT_1(fn, pfx##282, sfx), \ - PORT_1(fn, pfx##288, sfx), PORT_1(fn, pfx##289, sfx), \ - PORT_10(fn, pfx##29, sfx), PORT_10(fn, pfx##30, sfx) - -enum { - PINMUX_RESERVED = 0, - - PINMUX_DATA_BEGIN, - PORT_ALL(DATA), /* PORT0_DATA -> PORT309_DATA */ - PINMUX_DATA_END, - - PINMUX_INPUT_BEGIN, - PORT_ALL(IN), /* PORT0_IN -> PORT309_IN */ - PINMUX_INPUT_END, - - PINMUX_INPUT_PULLUP_BEGIN, - PORT_ALL(IN_PU), /* PORT0_IN_PU -> PORT309_IN_PU */ - PINMUX_INPUT_PULLUP_END, - - PINMUX_INPUT_PULLDOWN_BEGIN, - PORT_ALL(IN_PD), /* PORT0_IN_PD -> PORT309_IN_PD */ - PINMUX_INPUT_PULLDOWN_END, - - PINMUX_OUTPUT_BEGIN, - PORT_ALL(OUT), /* PORT0_OUT -> PORT309_OUT */ - PINMUX_OUTPUT_END, - - PINMUX_FUNCTION_BEGIN, - PORT_ALL(FN_IN), /* PORT0_FN_IN -> PORT309_FN_IN */ - PORT_ALL(FN_OUT), /* PORT0_FN_OUT -> PORT309_FN_OUT */ - PORT_ALL(FN0), /* PORT0_FN0 -> PORT309_FN0 */ - PORT_ALL(FN1), /* PORT0_FN1 -> PORT309_FN1 */ - PORT_ALL(FN2), /* PORT0_FN2 -> PORT309_FN2 */ - PORT_ALL(FN3), /* PORT0_FN3 -> PORT309_FN3 */ - PORT_ALL(FN4), /* PORT0_FN4 -> PORT309_FN4 */ - PORT_ALL(FN5), /* PORT0_FN5 -> PORT309_FN5 */ - PORT_ALL(FN6), /* PORT0_FN6 -> PORT309_FN6 */ - PORT_ALL(FN7), /* PORT0_FN7 -> PORT309_FN7 */ - - MSEL2CR_MSEL19_0, MSEL2CR_MSEL19_1, - MSEL2CR_MSEL18_0, MSEL2CR_MSEL18_1, - MSEL2CR_MSEL17_0, MSEL2CR_MSEL17_1, - MSEL2CR_MSEL16_0, MSEL2CR_MSEL16_1, - MSEL2CR_MSEL14_0, MSEL2CR_MSEL14_1, - MSEL2CR_MSEL13_0, MSEL2CR_MSEL13_1, - MSEL2CR_MSEL12_0, MSEL2CR_MSEL12_1, - MSEL2CR_MSEL11_0, MSEL2CR_MSEL11_1, - MSEL2CR_MSEL10_0, MSEL2CR_MSEL10_1, - MSEL2CR_MSEL9_0, MSEL2CR_MSEL9_1, - MSEL2CR_MSEL8_0, MSEL2CR_MSEL8_1, - MSEL2CR_MSEL7_0, MSEL2CR_MSEL7_1, - MSEL2CR_MSEL6_0, MSEL2CR_MSEL6_1, - MSEL2CR_MSEL4_0, MSEL2CR_MSEL4_1, - MSEL2CR_MSEL5_0, MSEL2CR_MSEL5_1, - MSEL2CR_MSEL3_0, MSEL2CR_MSEL3_1, - MSEL2CR_MSEL2_0, MSEL2CR_MSEL2_1, - MSEL2CR_MSEL1_0, MSEL2CR_MSEL1_1, - MSEL2CR_MSEL0_0, MSEL2CR_MSEL0_1, - MSEL3CR_MSEL28_0, MSEL3CR_MSEL28_1, - MSEL3CR_MSEL15_0, MSEL3CR_MSEL15_1, - MSEL3CR_MSEL11_0, MSEL3CR_MSEL11_1, - MSEL3CR_MSEL9_0, MSEL3CR_MSEL9_1, - MSEL3CR_MSEL6_0, MSEL3CR_MSEL6_1, - MSEL3CR_MSEL2_0, MSEL3CR_MSEL2_1, - MSEL4CR_MSEL29_0, MSEL4CR_MSEL29_1, - MSEL4CR_MSEL27_0, MSEL4CR_MSEL27_1, - MSEL4CR_MSEL26_0, MSEL4CR_MSEL26_1, - MSEL4CR_MSEL22_0, MSEL4CR_MSEL22_1, - MSEL4CR_MSEL21_0, MSEL4CR_MSEL21_1, - MSEL4CR_MSEL20_0, MSEL4CR_MSEL20_1, - MSEL4CR_MSEL19_0, MSEL4CR_MSEL19_1, - MSEL4CR_MSEL15_0, MSEL4CR_MSEL15_1, - MSEL4CR_MSEL13_0, MSEL4CR_MSEL13_1, - MSEL4CR_MSEL12_0, MSEL4CR_MSEL12_1, - MSEL4CR_MSEL11_0, MSEL4CR_MSEL11_1, - MSEL4CR_MSEL10_0, MSEL4CR_MSEL10_1, - MSEL4CR_MSEL9_0, MSEL4CR_MSEL9_1, - MSEL4CR_MSEL8_0, MSEL4CR_MSEL8_1, - MSEL4CR_MSEL7_0, MSEL4CR_MSEL7_1, - MSEL4CR_MSEL4_0, MSEL4CR_MSEL4_1, - MSEL4CR_MSEL1_0, MSEL4CR_MSEL1_1, - PINMUX_FUNCTION_END, - - PINMUX_MARK_BEGIN, - /* Hardware manual Table 25-1 (Function 0-7) */ - VBUS_0_MARK, - GPI0_MARK, - GPI1_MARK, - GPI2_MARK, - GPI3_MARK, - GPI4_MARK, - GPI5_MARK, - GPI6_MARK, - GPI7_MARK, - SCIFA7_RXD_MARK, - SCIFA7_CTS__MARK, - GPO7_MARK, MFG0_OUT2_MARK, - GPO6_MARK, MFG1_OUT2_MARK, - GPO5_MARK, SCIFA0_SCK_MARK, FSICOSLDT3_MARK, PORT16_VIO_CKOR_MARK, - SCIFA0_TXD_MARK, - SCIFA7_TXD_MARK, - SCIFA7_RTS__MARK, PORT19_VIO_CKO2_MARK, - GPO0_MARK, - GPO1_MARK, - GPO2_MARK, STATUS0_MARK, - GPO3_MARK, STATUS1_MARK, - GPO4_MARK, STATUS2_MARK, - VINT_MARK, - TCKON_MARK, - XDVFS1_MARK, PORT27_I2C_SCL2_MARK, PORT27_I2C_SCL3_MARK, \ - MFG0_OUT1_MARK, PORT27_IROUT_MARK, - XDVFS2_MARK, PORT28_I2C_SDA2_MARK, PORT28_I2C_SDA3_MARK, \ - PORT28_TPU1TO1_MARK, - SIM_RST_MARK, PORT29_TPU1TO1_MARK, - SIM_CLK_MARK, PORT30_VIO_CKOR_MARK, - SIM_D_MARK, PORT31_IROUT_MARK, - SCIFA4_TXD_MARK, - SCIFA4_RXD_MARK, XWUP_MARK, - SCIFA4_RTS__MARK, - SCIFA4_CTS__MARK, - FSIBOBT_MARK, FSIBIBT_MARK, - FSIBOLR_MARK, FSIBILR_MARK, - FSIBOSLD_MARK, - FSIBISLD_MARK, - VACK_MARK, - XTAL1L_MARK, - SCIFA0_RTS__MARK, FSICOSLDT2_MARK, - SCIFA0_RXD_MARK, - SCIFA0_CTS__MARK, FSICOSLDT1_MARK, - FSICOBT_MARK, FSICIBT_MARK, FSIDOBT_MARK, FSIDIBT_MARK, - FSICOLR_MARK, FSICILR_MARK, FSIDOLR_MARK, FSIDILR_MARK, - FSICOSLD_MARK, PORT47_FSICSPDIF_MARK, - FSICISLD_MARK, FSIDISLD_MARK, - FSIACK_MARK, PORT49_IRDA_OUT_MARK, PORT49_IROUT_MARK, FSIAOMC_MARK, - FSIAOLR_MARK, BBIF2_TSYNC2_MARK, TPU2TO2_MARK, FSIAILR_MARK, - - FSIAOBT_MARK, BBIF2_TSCK2_MARK, TPU2TO3_MARK, FSIAIBT_MARK, - FSIAOSLD_MARK, BBIF2_TXD2_MARK, - FSIASPDIF_MARK, PORT53_IRDA_IN_MARK, TPU3TO3_MARK, FSIBSPDIF_MARK, \ - PORT53_FSICSPDIF_MARK, - FSIBCK_MARK, PORT54_IRDA_FIRSEL_MARK, TPU3TO2_MARK, FSIBOMC_MARK, \ - FSICCK_MARK, FSICOMC_MARK, - FSIAISLD_MARK, TPU0TO0_MARK, - A0_MARK, BS__MARK, - A12_MARK, PORT58_KEYOUT7_MARK, TPU4TO2_MARK, - A13_MARK, PORT59_KEYOUT6_MARK, TPU0TO1_MARK, - A14_MARK, KEYOUT5_MARK, - A15_MARK, KEYOUT4_MARK, - A16_MARK, KEYOUT3_MARK, MSIOF0_SS1_MARK, - A17_MARK, KEYOUT2_MARK, MSIOF0_TSYNC_MARK, - A18_MARK, KEYOUT1_MARK, MSIOF0_TSCK_MARK, - A19_MARK, KEYOUT0_MARK, MSIOF0_TXD_MARK, - A20_MARK, KEYIN0_MARK, MSIOF0_RSCK_MARK, - A21_MARK, KEYIN1_MARK, MSIOF0_RSYNC_MARK, - A22_MARK, KEYIN2_MARK, MSIOF0_MCK0_MARK, - A23_MARK, KEYIN3_MARK, MSIOF0_MCK1_MARK, - A24_MARK, KEYIN4_MARK, MSIOF0_RXD_MARK, - A25_MARK, KEYIN5_MARK, MSIOF0_SS2_MARK, - A26_MARK, KEYIN6_MARK, - KEYIN7_MARK, - D0_NAF0_MARK, - D1_NAF1_MARK, - D2_NAF2_MARK, - D3_NAF3_MARK, - D4_NAF4_MARK, - D5_NAF5_MARK, - D6_NAF6_MARK, - D7_NAF7_MARK, - D8_NAF8_MARK, - D9_NAF9_MARK, - D10_NAF10_MARK, - D11_NAF11_MARK, - D12_NAF12_MARK, - D13_NAF13_MARK, - D14_NAF14_MARK, - D15_NAF15_MARK, - CS4__MARK, - CS5A__MARK, PORT91_RDWR_MARK, - CS5B__MARK, FCE1__MARK, - CS6B__MARK, DACK0_MARK, - FCE0__MARK, CS6A__MARK, - WAIT__MARK, DREQ0_MARK, - RD__FSC_MARK, - WE0__FWE_MARK, RDWR_FWE_MARK, - WE1__MARK, - FRB_MARK, - CKO_MARK, - NBRSTOUT__MARK, - NBRST__MARK, - BBIF2_TXD_MARK, - BBIF2_RXD_MARK, - BBIF2_SYNC_MARK, - BBIF2_SCK_MARK, - SCIFA3_CTS__MARK, MFG3_IN2_MARK, - SCIFA3_RXD_MARK, MFG3_IN1_MARK, - BBIF1_SS2_MARK, SCIFA3_RTS__MARK, MFG3_OUT1_MARK, - SCIFA3_TXD_MARK, - HSI_RX_DATA_MARK, BBIF1_RXD_MARK, - HSI_TX_WAKE_MARK, BBIF1_TSCK_MARK, - HSI_TX_DATA_MARK, BBIF1_TSYNC_MARK, - HSI_TX_READY_MARK, BBIF1_TXD_MARK, - HSI_RX_READY_MARK, BBIF1_RSCK_MARK, PORT115_I2C_SCL2_MARK, \ - PORT115_I2C_SCL3_MARK, - HSI_RX_WAKE_MARK, BBIF1_RSYNC_MARK, PORT116_I2C_SDA2_MARK, \ - PORT116_I2C_SDA3_MARK, - HSI_RX_FLAG_MARK, BBIF1_SS1_MARK, BBIF1_FLOW_MARK, - HSI_TX_FLAG_MARK, - VIO_VD_MARK, PORT128_LCD2VSYN_MARK, VIO2_VD_MARK, LCD2D0_MARK, - - VIO_HD_MARK, PORT129_LCD2HSYN_MARK, PORT129_LCD2CS__MARK, \ - VIO2_HD_MARK, LCD2D1_MARK, - VIO_D0_MARK, PORT130_MSIOF2_RXD_MARK, LCD2D10_MARK, - VIO_D1_MARK, PORT131_KEYOUT6_MARK, PORT131_MSIOF2_SS1_MARK, \ - PORT131_KEYOUT11_MARK, LCD2D11_MARK, - VIO_D2_MARK, PORT132_KEYOUT7_MARK, PORT132_MSIOF2_SS2_MARK, \ - PORT132_KEYOUT10_MARK, LCD2D12_MARK, - VIO_D3_MARK, MSIOF2_TSYNC_MARK, LCD2D13_MARK, - VIO_D4_MARK, MSIOF2_TXD_MARK, LCD2D14_MARK, - VIO_D5_MARK, MSIOF2_TSCK_MARK, LCD2D15_MARK, - VIO_D6_MARK, PORT136_KEYOUT8_MARK, LCD2D16_MARK, - VIO_D7_MARK, PORT137_KEYOUT9_MARK, LCD2D17_MARK, - VIO_D8_MARK, PORT138_KEYOUT8_MARK, VIO2_D0_MARK, LCD2D6_MARK, - VIO_D9_MARK, PORT139_KEYOUT9_MARK, VIO2_D1_MARK, LCD2D7_MARK, - VIO_D10_MARK, TPU0TO2_MARK, VIO2_D2_MARK, LCD2D8_MARK, - VIO_D11_MARK, TPU0TO3_MARK, VIO2_D3_MARK, LCD2D9_MARK, - VIO_D12_MARK, PORT142_KEYOUT10_MARK, VIO2_D4_MARK, LCD2D2_MARK, - VIO_D13_MARK, PORT143_KEYOUT11_MARK, PORT143_KEYOUT6_MARK, \ - VIO2_D5_MARK, LCD2D3_MARK, - VIO_D14_MARK, PORT144_KEYOUT7_MARK, VIO2_D6_MARK, LCD2D4_MARK, - VIO_D15_MARK, TPU1TO3_MARK, PORT145_LCD2DISP_MARK, \ - PORT145_LCD2RS_MARK, VIO2_D7_MARK, LCD2D5_MARK, - VIO_CLK_MARK, LCD2DCK_MARK, PORT146_LCD2WR__MARK, VIO2_CLK_MARK, \ - LCD2D18_MARK, - VIO_FIELD_MARK, LCD2RD__MARK, VIO2_FIELD_MARK, LCD2D19_MARK, - VIO_CKO_MARK, - A27_MARK, PORT149_RDWR_MARK, MFG0_IN1_MARK, PORT149_KEYOUT9_MARK, - MFG0_IN2_MARK, - TS_SPSYNC3_MARK, MSIOF2_RSCK_MARK, - TS_SDAT3_MARK, MSIOF2_RSYNC_MARK, - TPU1TO2_MARK, TS_SDEN3_MARK, PORT153_MSIOF2_SS1_MARK, - SCIFA2_TXD1_MARK, MSIOF2_MCK0_MARK, - SCIFA2_RXD1_MARK, MSIOF2_MCK1_MARK, - SCIFA2_RTS1__MARK, PORT156_MSIOF2_SS2_MARK, - SCIFA2_CTS1__MARK, PORT157_MSIOF2_RXD_MARK, - DINT__MARK, SCIFA2_SCK1_MARK, TS_SCK3_MARK, - PORT159_SCIFB_SCK_MARK, PORT159_SCIFA5_SCK_MARK, NMI_MARK, - PORT160_SCIFB_TXD_MARK, PORT160_SCIFA5_TXD_MARK, - PORT161_SCIFB_CTS__MARK, PORT161_SCIFA5_CTS__MARK, - PORT162_SCIFB_RXD_MARK, PORT162_SCIFA5_RXD_MARK, - PORT163_SCIFB_RTS__MARK, PORT163_SCIFA5_RTS__MARK, TPU3TO0_MARK, - LCDD0_MARK, - LCDD1_MARK, PORT193_SCIFA5_CTS__MARK, BBIF2_TSYNC1_MARK, - LCDD2_MARK, PORT194_SCIFA5_RTS__MARK, BBIF2_TSCK1_MARK, - LCDD3_MARK, PORT195_SCIFA5_RXD_MARK, BBIF2_TXD1_MARK, - LCDD4_MARK, PORT196_SCIFA5_TXD_MARK, - LCDD5_MARK, PORT197_SCIFA5_SCK_MARK, MFG2_OUT2_MARK, TPU2TO1_MARK, - LCDD6_MARK, - LCDD7_MARK, TPU4TO1_MARK, MFG4_OUT2_MARK, - LCDD8_MARK, D16_MARK, - LCDD9_MARK, D17_MARK, - LCDD10_MARK, D18_MARK, - LCDD11_MARK, D19_MARK, - LCDD12_MARK, D20_MARK, - LCDD13_MARK, D21_MARK, - LCDD14_MARK, D22_MARK, - LCDD15_MARK, PORT207_MSIOF0L_SS1_MARK, D23_MARK, - LCDD16_MARK, PORT208_MSIOF0L_SS2_MARK, D24_MARK, - LCDD17_MARK, D25_MARK, - LCDD18_MARK, DREQ2_MARK, PORT210_MSIOF0L_SS1_MARK, D26_MARK, - LCDD19_MARK, PORT211_MSIOF0L_SS2_MARK, D27_MARK, - LCDD20_MARK, TS_SPSYNC1_MARK, MSIOF0L_MCK0_MARK, D28_MARK, - LCDD21_MARK, TS_SDAT1_MARK, MSIOF0L_MCK1_MARK, D29_MARK, - LCDD22_MARK, TS_SDEN1_MARK, MSIOF0L_RSCK_MARK, D30_MARK, - LCDD23_MARK, TS_SCK1_MARK, MSIOF0L_RSYNC_MARK, D31_MARK, - LCDDCK_MARK, LCDWR__MARK, - LCDRD__MARK, DACK2_MARK, PORT217_LCD2RS_MARK, MSIOF0L_TSYNC_MARK, \ - VIO2_FIELD3_MARK, PORT217_LCD2DISP_MARK, - LCDHSYN_MARK, LCDCS__MARK, LCDCS2__MARK, DACK3_MARK, \ - PORT218_VIO_CKOR_MARK, - LCDDISP_MARK, LCDRS_MARK, PORT219_LCD2WR__MARK, DREQ3_MARK, \ - MSIOF0L_TSCK_MARK, VIO2_CLK3_MARK, LCD2DCK_2_MARK, - LCDVSYN_MARK, LCDVSYN2_MARK, - LCDLCLK_MARK, DREQ1_MARK, PORT221_LCD2CS__MARK, PWEN_MARK, \ - MSIOF0L_RXD_MARK, VIO2_HD3_MARK, PORT221_LCD2HSYN_MARK, - LCDDON_MARK, LCDDON2_MARK, DACK1_MARK, OVCN_MARK, MSIOF0L_TXD_MARK, \ - VIO2_VD3_MARK, PORT222_LCD2VSYN_MARK, - - SCIFA1_TXD_MARK, OVCN2_MARK, - EXTLP_MARK, SCIFA1_SCK_MARK, PORT226_VIO_CKO2_MARK, - SCIFA1_RTS__MARK, IDIN_MARK, - SCIFA1_RXD_MARK, - SCIFA1_CTS__MARK, MFG1_IN1_MARK, - MSIOF1_TXD_MARK, SCIFA2_TXD2_MARK, - MSIOF1_TSYNC_MARK, SCIFA2_CTS2__MARK, - MSIOF1_TSCK_MARK, SCIFA2_SCK2_MARK, - MSIOF1_RXD_MARK, SCIFA2_RXD2_MARK, - MSIOF1_RSCK_MARK, SCIFA2_RTS2__MARK, VIO2_CLK2_MARK, LCD2D20_MARK, - MSIOF1_RSYNC_MARK, MFG1_IN2_MARK, VIO2_VD2_MARK, LCD2D21_MARK, - MSIOF1_MCK0_MARK, PORT236_I2C_SDA2_MARK, - MSIOF1_MCK1_MARK, PORT237_I2C_SCL2_MARK, - MSIOF1_SS1_MARK, VIO2_FIELD2_MARK, LCD2D22_MARK, - MSIOF1_SS2_MARK, VIO2_HD2_MARK, LCD2D23_MARK, - SCIFA6_TXD_MARK, - PORT241_IRDA_OUT_MARK, PORT241_IROUT_MARK, MFG4_OUT1_MARK, TPU4TO0_MARK, - PORT242_IRDA_IN_MARK, MFG4_IN2_MARK, - PORT243_IRDA_FIRSEL_MARK, PORT243_VIO_CKO2_MARK, - PORT244_SCIFA5_CTS__MARK, MFG2_IN1_MARK, PORT244_SCIFB_CTS__MARK, \ - MSIOF2R_RXD_MARK, - PORT245_SCIFA5_RTS__MARK, MFG2_IN2_MARK, PORT245_SCIFB_RTS__MARK, \ - MSIOF2R_TXD_MARK, - PORT246_SCIFA5_RXD_MARK, MFG1_OUT1_MARK, PORT246_SCIFB_RXD_MARK, \ - TPU1TO0_MARK, - PORT247_SCIFA5_TXD_MARK, MFG3_OUT2_MARK, PORT247_SCIFB_TXD_MARK, \ - TPU3TO1_MARK, - PORT248_SCIFA5_SCK_MARK, MFG2_OUT1_MARK, PORT248_SCIFB_SCK_MARK, \ - TPU2TO0_MARK, PORT248_I2C_SCL3_MARK, MSIOF2R_TSCK_MARK, - PORT249_IROUT_MARK, MFG4_IN1_MARK, PORT249_I2C_SDA3_MARK, \ - MSIOF2R_TSYNC_MARK, - SDHICLK0_MARK, - SDHICD0_MARK, - SDHID0_0_MARK, - SDHID0_1_MARK, - SDHID0_2_MARK, - SDHID0_3_MARK, - SDHICMD0_MARK, - SDHIWP0_MARK, - SDHICLK1_MARK, - SDHID1_0_MARK, TS_SPSYNC2_MARK, - SDHID1_1_MARK, TS_SDAT2_MARK, - SDHID1_2_MARK, TS_SDEN2_MARK, - SDHID1_3_MARK, TS_SCK2_MARK, - SDHICMD1_MARK, - SDHICLK2_MARK, - SDHID2_0_MARK, TS_SPSYNC4_MARK, - SDHID2_1_MARK, TS_SDAT4_MARK, - SDHID2_2_MARK, TS_SDEN4_MARK, - SDHID2_3_MARK, TS_SCK4_MARK, - SDHICMD2_MARK, - MMCCLK0_MARK, - MMCD0_0_MARK, - MMCD0_1_MARK, - MMCD0_2_MARK, - MMCD0_3_MARK, - MMCD0_4_MARK, TS_SPSYNC5_MARK, - MMCD0_5_MARK, TS_SDAT5_MARK, - MMCD0_6_MARK, TS_SDEN5_MARK, - MMCD0_7_MARK, TS_SCK5_MARK, - MMCCMD0_MARK, - RESETOUTS__MARK, EXTAL2OUT_MARK, - MCP_WAIT__MCP_FRB_MARK, - MCP_CKO_MARK, MMCCLK1_MARK, - MCP_D15_MCP_NAF15_MARK, - MCP_D14_MCP_NAF14_MARK, - MCP_D13_MCP_NAF13_MARK, - MCP_D12_MCP_NAF12_MARK, - MCP_D11_MCP_NAF11_MARK, - MCP_D10_MCP_NAF10_MARK, - MCP_D9_MCP_NAF9_MARK, - MCP_D8_MCP_NAF8_MARK, MMCCMD1_MARK, - MCP_D7_MCP_NAF7_MARK, MMCD1_7_MARK, - - MCP_D6_MCP_NAF6_MARK, MMCD1_6_MARK, - MCP_D5_MCP_NAF5_MARK, MMCD1_5_MARK, - MCP_D4_MCP_NAF4_MARK, MMCD1_4_MARK, - MCP_D3_MCP_NAF3_MARK, MMCD1_3_MARK, - MCP_D2_MCP_NAF2_MARK, MMCD1_2_MARK, - MCP_D1_MCP_NAF1_MARK, MMCD1_1_MARK, - MCP_D0_MCP_NAF0_MARK, MMCD1_0_MARK, - MCP_NBRSTOUT__MARK, - MCP_WE0__MCP_FWE_MARK, MCP_RDWR_MCP_FWE_MARK, - - /* MSEL2 special cases */ - TSIF2_TS_XX1_MARK, - TSIF2_TS_XX2_MARK, - TSIF2_TS_XX3_MARK, - TSIF2_TS_XX4_MARK, - TSIF2_TS_XX5_MARK, - TSIF1_TS_XX1_MARK, - TSIF1_TS_XX2_MARK, - TSIF1_TS_XX3_MARK, - TSIF1_TS_XX4_MARK, - TSIF1_TS_XX5_MARK, - TSIF0_TS_XX1_MARK, - TSIF0_TS_XX2_MARK, - TSIF0_TS_XX3_MARK, - TSIF0_TS_XX4_MARK, - TSIF0_TS_XX5_MARK, - MST1_TS_XX1_MARK, - MST1_TS_XX2_MARK, - MST1_TS_XX3_MARK, - MST1_TS_XX4_MARK, - MST1_TS_XX5_MARK, - MST0_TS_XX1_MARK, - MST0_TS_XX2_MARK, - MST0_TS_XX3_MARK, - MST0_TS_XX4_MARK, - MST0_TS_XX5_MARK, - - /* MSEL3 special cases */ - SDHI0_VCCQ_MC0_ON_MARK, - SDHI0_VCCQ_MC0_OFF_MARK, - DEBUG_MON_VIO_MARK, - DEBUG_MON_LCDD_MARK, - LCDC_LCDC0_MARK, - LCDC_LCDC1_MARK, - - /* MSEL4 special cases */ - IRQ9_MEM_INT_MARK, - IRQ9_MCP_INT_MARK, - A11_MARK, - KEYOUT8_MARK, - TPU4TO3_MARK, - RESETA_N_PU_ON_MARK, - RESETA_N_PU_OFF_MARK, - EDBGREQ_PD_MARK, - EDBGREQ_PU_MARK, - - /* Functions with pull-ups */ - KEYIN0_PU_MARK, - KEYIN1_PU_MARK, - KEYIN2_PU_MARK, - KEYIN3_PU_MARK, - KEYIN4_PU_MARK, - KEYIN5_PU_MARK, - KEYIN6_PU_MARK, - KEYIN7_PU_MARK, - SDHICD0_PU_MARK, - SDHID0_0_PU_MARK, - SDHID0_1_PU_MARK, - SDHID0_2_PU_MARK, - SDHID0_3_PU_MARK, - SDHICMD0_PU_MARK, - SDHIWP0_PU_MARK, - SDHID1_0_PU_MARK, - SDHID1_1_PU_MARK, - SDHID1_2_PU_MARK, - SDHID1_3_PU_MARK, - SDHICMD1_PU_MARK, - SDHID2_0_PU_MARK, - SDHID2_1_PU_MARK, - SDHID2_2_PU_MARK, - SDHID2_3_PU_MARK, - SDHICMD2_PU_MARK, - MMCCMD0_PU_MARK, - MMCCMD1_PU_MARK, - MMCD0_0_PU_MARK, - MMCD0_1_PU_MARK, - MMCD0_2_PU_MARK, - MMCD0_3_PU_MARK, - MMCD0_4_PU_MARK, - MMCD0_5_PU_MARK, - MMCD0_6_PU_MARK, - MMCD0_7_PU_MARK, - FSIBISLD_PU_MARK, - FSIACK_PU_MARK, - FSIAILR_PU_MARK, - FSIAIBT_PU_MARK, - FSIAISLD_PU_MARK, - - PINMUX_MARK_END, -}; - -static unsigned short pinmux_data[] = { - /* specify valid pin states for each pin in GPIO mode */ - - /* Table 25-1 (I/O and Pull U/D) */ - PORT_DATA_I_PD(0), - PORT_DATA_I_PU(1), - PORT_DATA_I_PU(2), - PORT_DATA_I_PU(3), - PORT_DATA_I_PU(4), - PORT_DATA_I_PU(5), - PORT_DATA_I_PU(6), - PORT_DATA_I_PU(7), - PORT_DATA_I_PU(8), - PORT_DATA_I_PD(9), - PORT_DATA_I_PD(10), - PORT_DATA_I_PU_PD(11), - PORT_DATA_IO_PU_PD(12), - PORT_DATA_IO_PU_PD(13), - PORT_DATA_IO_PU_PD(14), - PORT_DATA_IO_PU_PD(15), - PORT_DATA_IO_PD(16), - PORT_DATA_IO_PD(17), - PORT_DATA_IO_PU(18), - PORT_DATA_IO_PU(19), - PORT_DATA_O(20), - PORT_DATA_O(21), - PORT_DATA_O(22), - PORT_DATA_O(23), - PORT_DATA_O(24), - PORT_DATA_I_PD(25), - PORT_DATA_I_PD(26), - PORT_DATA_IO_PU(27), - PORT_DATA_IO_PU(28), - PORT_DATA_IO_PD(29), - PORT_DATA_IO_PD(30), - PORT_DATA_IO_PU(31), - PORT_DATA_IO_PD(32), - PORT_DATA_I_PU_PD(33), - PORT_DATA_IO_PD(34), - PORT_DATA_I_PU_PD(35), - PORT_DATA_IO_PD(36), - PORT_DATA_IO(37), - PORT_DATA_O(38), - PORT_DATA_I_PU(39), - PORT_DATA_I_PU_PD(40), - PORT_DATA_O(41), - PORT_DATA_IO_PD(42), - PORT_DATA_IO_PU_PD(43), - PORT_DATA_IO_PU_PD(44), - PORT_DATA_IO_PD(45), - PORT_DATA_IO_PD(46), - PORT_DATA_IO_PD(47), - PORT_DATA_I_PD(48), - PORT_DATA_IO_PU_PD(49), - PORT_DATA_IO_PD(50), - - PORT_DATA_IO_PD(51), - PORT_DATA_O(52), - PORT_DATA_IO_PU_PD(53), - PORT_DATA_IO_PU_PD(54), - PORT_DATA_IO_PD(55), - PORT_DATA_I_PU_PD(56), - PORT_DATA_IO(57), - PORT_DATA_IO(58), - PORT_DATA_IO(59), - PORT_DATA_IO(60), - PORT_DATA_IO(61), - PORT_DATA_IO_PD(62), - PORT_DATA_IO_PD(63), - PORT_DATA_IO_PU_PD(64), - PORT_DATA_IO_PD(65), - PORT_DATA_IO_PU_PD(66), - PORT_DATA_IO_PU_PD(67), - PORT_DATA_IO_PU_PD(68), - PORT_DATA_IO_PU_PD(69), - PORT_DATA_IO_PU_PD(70), - PORT_DATA_IO_PU_PD(71), - PORT_DATA_IO_PU_PD(72), - PORT_DATA_I_PU_PD(73), - PORT_DATA_IO_PU(74), - PORT_DATA_IO_PU(75), - PORT_DATA_IO_PU(76), - PORT_DATA_IO_PU(77), - PORT_DATA_IO_PU(78), - PORT_DATA_IO_PU(79), - PORT_DATA_IO_PU(80), - PORT_DATA_IO_PU(81), - PORT_DATA_IO_PU(82), - PORT_DATA_IO_PU(83), - PORT_DATA_IO_PU(84), - PORT_DATA_IO_PU(85), - PORT_DATA_IO_PU(86), - PORT_DATA_IO_PU(87), - PORT_DATA_IO_PU(88), - PORT_DATA_IO_PU(89), - PORT_DATA_O(90), - PORT_DATA_IO_PU(91), - PORT_DATA_O(92), - PORT_DATA_IO_PU(93), - PORT_DATA_O(94), - PORT_DATA_I_PU_PD(95), - PORT_DATA_IO(96), - PORT_DATA_IO(97), - PORT_DATA_IO(98), - PORT_DATA_I_PU(99), - PORT_DATA_O(100), - PORT_DATA_O(101), - PORT_DATA_I_PU(102), - PORT_DATA_IO_PD(103), - PORT_DATA_I_PU_PD(104), - PORT_DATA_I_PD(105), - PORT_DATA_I_PD(106), - PORT_DATA_I_PU_PD(107), - PORT_DATA_I_PU_PD(108), - PORT_DATA_IO_PD(109), - PORT_DATA_IO_PD(110), - PORT_DATA_IO_PU_PD(111), - PORT_DATA_IO_PU_PD(112), - PORT_DATA_IO_PU_PD(113), - PORT_DATA_IO_PD(114), - PORT_DATA_IO_PU(115), - PORT_DATA_IO_PU(116), - PORT_DATA_IO_PU_PD(117), - PORT_DATA_IO_PU_PD(118), - PORT_DATA_IO_PD(128), - - PORT_DATA_IO_PD(129), - PORT_DATA_IO_PU_PD(130), - PORT_DATA_IO_PD(131), - PORT_DATA_IO_PD(132), - PORT_DATA_IO_PD(133), - PORT_DATA_IO_PU_PD(134), - PORT_DATA_IO_PU_PD(135), - PORT_DATA_IO_PU_PD(136), - PORT_DATA_IO_PU_PD(137), - PORT_DATA_IO_PD(138), - PORT_DATA_IO_PD(139), - PORT_DATA_IO_PD(140), - PORT_DATA_IO_PD(141), - PORT_DATA_IO_PD(142), - PORT_DATA_IO_PD(143), - PORT_DATA_IO_PU_PD(144), - PORT_DATA_IO_PD(145), - PORT_DATA_IO_PU_PD(146), - PORT_DATA_IO_PU_PD(147), - PORT_DATA_IO_PU_PD(148), - PORT_DATA_IO_PU_PD(149), - PORT_DATA_I_PU_PD(150), - PORT_DATA_IO_PU_PD(151), - PORT_DATA_IO_PU_PD(152), - PORT_DATA_IO_PD(153), - PORT_DATA_IO_PD(154), - PORT_DATA_I_PU_PD(155), - PORT_DATA_IO_PU_PD(156), - PORT_DATA_I_PD(157), - PORT_DATA_IO_PD(158), - PORT_DATA_IO_PU_PD(159), - PORT_DATA_IO_PU_PD(160), - PORT_DATA_I_PU_PD(161), - PORT_DATA_I_PU_PD(162), - PORT_DATA_IO_PU_PD(163), - PORT_DATA_I_PU_PD(164), - PORT_DATA_IO_PD(192), - PORT_DATA_IO_PU_PD(193), - PORT_DATA_IO_PD(194), - PORT_DATA_IO_PU_PD(195), - PORT_DATA_IO_PD(196), - PORT_DATA_IO_PD(197), - PORT_DATA_IO_PD(198), - PORT_DATA_IO_PD(199), - PORT_DATA_IO_PU_PD(200), - PORT_DATA_IO_PU_PD(201), - PORT_DATA_IO_PU_PD(202), - PORT_DATA_IO_PU_PD(203), - PORT_DATA_IO_PU_PD(204), - PORT_DATA_IO_PU_PD(205), - PORT_DATA_IO_PU_PD(206), - PORT_DATA_IO_PD(207), - PORT_DATA_IO_PD(208), - PORT_DATA_IO_PD(209), - PORT_DATA_IO_PD(210), - PORT_DATA_IO_PD(211), - PORT_DATA_IO_PD(212), - PORT_DATA_IO_PD(213), - PORT_DATA_IO_PU_PD(214), - PORT_DATA_IO_PU_PD(215), - PORT_DATA_IO_PD(216), - PORT_DATA_IO_PD(217), - PORT_DATA_O(218), - PORT_DATA_IO_PD(219), - PORT_DATA_IO_PD(220), - PORT_DATA_IO_PU_PD(221), - PORT_DATA_IO_PU_PD(222), - PORT_DATA_I_PU_PD(223), - PORT_DATA_I_PU_PD(224), - - PORT_DATA_IO_PU_PD(225), - PORT_DATA_O(226), - PORT_DATA_IO_PU_PD(227), - PORT_DATA_I_PU_PD(228), - PORT_DATA_I_PD(229), - PORT_DATA_IO(230), - PORT_DATA_IO_PU_PD(231), - PORT_DATA_IO_PU_PD(232), - PORT_DATA_I_PU_PD(233), - PORT_DATA_IO_PU_PD(234), - PORT_DATA_IO_PU_PD(235), - PORT_DATA_IO_PU_PD(236), - PORT_DATA_IO_PD(237), - PORT_DATA_IO_PU_PD(238), - PORT_DATA_IO_PU_PD(239), - PORT_DATA_IO_PU_PD(240), - PORT_DATA_O(241), - PORT_DATA_I_PD(242), - PORT_DATA_IO_PU_PD(243), - PORT_DATA_IO_PU_PD(244), - PORT_DATA_IO_PU_PD(245), - PORT_DATA_IO_PU_PD(246), - PORT_DATA_IO_PU_PD(247), - PORT_DATA_IO_PU_PD(248), - PORT_DATA_IO_PU_PD(249), - PORT_DATA_IO_PU_PD(250), - PORT_DATA_IO_PU_PD(251), - PORT_DATA_IO_PU_PD(252), - PORT_DATA_IO_PU_PD(253), - PORT_DATA_IO_PU_PD(254), - PORT_DATA_IO_PU_PD(255), - PORT_DATA_IO_PU_PD(256), - PORT_DATA_IO_PU_PD(257), - PORT_DATA_IO_PU_PD(258), - PORT_DATA_IO_PU_PD(259), - PORT_DATA_IO_PU_PD(260), - PORT_DATA_IO_PU_PD(261), - PORT_DATA_IO_PU_PD(262), - PORT_DATA_IO_PU_PD(263), - PORT_DATA_IO_PU_PD(264), - PORT_DATA_IO_PU_PD(265), - PORT_DATA_IO_PU_PD(266), - PORT_DATA_IO_PU_PD(267), - PORT_DATA_IO_PU_PD(268), - PORT_DATA_IO_PU_PD(269), - PORT_DATA_IO_PU_PD(270), - PORT_DATA_IO_PU_PD(271), - PORT_DATA_IO_PU_PD(272), - PORT_DATA_IO_PU_PD(273), - PORT_DATA_IO_PU_PD(274), - PORT_DATA_IO_PU_PD(275), - PORT_DATA_IO_PU_PD(276), - PORT_DATA_IO_PU_PD(277), - PORT_DATA_IO_PU_PD(278), - PORT_DATA_IO_PU_PD(279), - PORT_DATA_IO_PU_PD(280), - PORT_DATA_O(281), - PORT_DATA_O(282), - PORT_DATA_I_PU(288), - PORT_DATA_IO_PU_PD(289), - PORT_DATA_IO_PU_PD(290), - PORT_DATA_IO_PU_PD(291), - PORT_DATA_IO_PU_PD(292), - PORT_DATA_IO_PU_PD(293), - PORT_DATA_IO_PU_PD(294), - PORT_DATA_IO_PU_PD(295), - PORT_DATA_IO_PU_PD(296), - PORT_DATA_IO_PU_PD(297), - PORT_DATA_IO_PU_PD(298), - - PORT_DATA_IO_PU_PD(299), - PORT_DATA_IO_PU_PD(300), - PORT_DATA_IO_PU_PD(301), - PORT_DATA_IO_PU_PD(302), - PORT_DATA_IO_PU_PD(303), - PORT_DATA_IO_PU_PD(304), - PORT_DATA_IO_PU_PD(305), - PORT_DATA_O(306), - PORT_DATA_O(307), - PORT_DATA_I_PU(308), - PORT_DATA_O(309), - - /* Table 25-1 (Function 0-7) */ - PINMUX_DATA(VBUS_0_MARK, PORT0_FN1), - PINMUX_DATA(GPI0_MARK, PORT1_FN1), - PINMUX_DATA(GPI1_MARK, PORT2_FN1), - PINMUX_DATA(GPI2_MARK, PORT3_FN1), - PINMUX_DATA(GPI3_MARK, PORT4_FN1), - PINMUX_DATA(GPI4_MARK, PORT5_FN1), - PINMUX_DATA(GPI5_MARK, PORT6_FN1), - PINMUX_DATA(GPI6_MARK, PORT7_FN1), - PINMUX_DATA(GPI7_MARK, PORT8_FN1), - PINMUX_DATA(SCIFA7_RXD_MARK, PORT12_FN2), - PINMUX_DATA(SCIFA7_CTS__MARK, PORT13_FN2), - PINMUX_DATA(GPO7_MARK, PORT14_FN1), \ - PINMUX_DATA(MFG0_OUT2_MARK, PORT14_FN4), - PINMUX_DATA(GPO6_MARK, PORT15_FN1), \ - PINMUX_DATA(MFG1_OUT2_MARK, PORT15_FN4), - PINMUX_DATA(GPO5_MARK, PORT16_FN1), \ - PINMUX_DATA(SCIFA0_SCK_MARK, PORT16_FN2), \ - PINMUX_DATA(FSICOSLDT3_MARK, PORT16_FN3), \ - PINMUX_DATA(PORT16_VIO_CKOR_MARK, PORT16_FN4), - PINMUX_DATA(SCIFA0_TXD_MARK, PORT17_FN2), - PINMUX_DATA(SCIFA7_TXD_MARK, PORT18_FN2), - PINMUX_DATA(SCIFA7_RTS__MARK, PORT19_FN2), \ - PINMUX_DATA(PORT19_VIO_CKO2_MARK, PORT19_FN3), - PINMUX_DATA(GPO0_MARK, PORT20_FN1), - PINMUX_DATA(GPO1_MARK, PORT21_FN1), - PINMUX_DATA(GPO2_MARK, PORT22_FN1), \ - PINMUX_DATA(STATUS0_MARK, PORT22_FN2), - PINMUX_DATA(GPO3_MARK, PORT23_FN1), \ - PINMUX_DATA(STATUS1_MARK, PORT23_FN2), - PINMUX_DATA(GPO4_MARK, PORT24_FN1), \ - PINMUX_DATA(STATUS2_MARK, PORT24_FN2), - PINMUX_DATA(VINT_MARK, PORT25_FN1), - PINMUX_DATA(TCKON_MARK, PORT26_FN1), - PINMUX_DATA(XDVFS1_MARK, PORT27_FN1), \ - PINMUX_DATA(PORT27_I2C_SCL2_MARK, PORT27_FN2, MSEL2CR_MSEL17_0, - MSEL2CR_MSEL16_1), \ - PINMUX_DATA(PORT27_I2C_SCL3_MARK, PORT27_FN3, MSEL2CR_MSEL19_0, - MSEL2CR_MSEL18_1), \ - PINMUX_DATA(MFG0_OUT1_MARK, PORT27_FN4), \ - PINMUX_DATA(PORT27_IROUT_MARK, PORT27_FN7), - PINMUX_DATA(XDVFS2_MARK, PORT28_FN1), \ - PINMUX_DATA(PORT28_I2C_SDA2_MARK, PORT28_FN2, MSEL2CR_MSEL17_0, - MSEL2CR_MSEL16_1), \ - PINMUX_DATA(PORT28_I2C_SDA3_MARK, PORT28_FN3, MSEL2CR_MSEL19_0, - MSEL2CR_MSEL18_1), \ - PINMUX_DATA(PORT28_TPU1TO1_MARK, PORT28_FN7), - PINMUX_DATA(SIM_RST_MARK, PORT29_FN1), \ - PINMUX_DATA(PORT29_TPU1TO1_MARK, PORT29_FN4), - PINMUX_DATA(SIM_CLK_MARK, PORT30_FN1), \ - PINMUX_DATA(PORT30_VIO_CKOR_MARK, PORT30_FN4), - PINMUX_DATA(SIM_D_MARK, PORT31_FN1), \ - PINMUX_DATA(PORT31_IROUT_MARK, PORT31_FN4), - PINMUX_DATA(SCIFA4_TXD_MARK, PORT32_FN2), - PINMUX_DATA(SCIFA4_RXD_MARK, PORT33_FN2), \ - PINMUX_DATA(XWUP_MARK, PORT33_FN3), - PINMUX_DATA(SCIFA4_RTS__MARK, PORT34_FN2), - PINMUX_DATA(SCIFA4_CTS__MARK, PORT35_FN2), - PINMUX_DATA(FSIBOBT_MARK, PORT36_FN1), \ - PINMUX_DATA(FSIBIBT_MARK, PORT36_FN2), - PINMUX_DATA(FSIBOLR_MARK, PORT37_FN1), \ - PINMUX_DATA(FSIBILR_MARK, PORT37_FN2), - PINMUX_DATA(FSIBOSLD_MARK, PORT38_FN1), - PINMUX_DATA(FSIBISLD_MARK, PORT39_FN1), - PINMUX_DATA(VACK_MARK, PORT40_FN1), - PINMUX_DATA(XTAL1L_MARK, PORT41_FN1), - PINMUX_DATA(SCIFA0_RTS__MARK, PORT42_FN2), \ - PINMUX_DATA(FSICOSLDT2_MARK, PORT42_FN3), - PINMUX_DATA(SCIFA0_RXD_MARK, PORT43_FN2), - PINMUX_DATA(SCIFA0_CTS__MARK, PORT44_FN2), \ - PINMUX_DATA(FSICOSLDT1_MARK, PORT44_FN3), - PINMUX_DATA(FSICOBT_MARK, PORT45_FN1), \ - PINMUX_DATA(FSICIBT_MARK, PORT45_FN2), \ - PINMUX_DATA(FSIDOBT_MARK, PORT45_FN3), \ - PINMUX_DATA(FSIDIBT_MARK, PORT45_FN4), - PINMUX_DATA(FSICOLR_MARK, PORT46_FN1), \ - PINMUX_DATA(FSICILR_MARK, PORT46_FN2), \ - PINMUX_DATA(FSIDOLR_MARK, PORT46_FN3), \ - PINMUX_DATA(FSIDILR_MARK, PORT46_FN4), - PINMUX_DATA(FSICOSLD_MARK, PORT47_FN1), \ - PINMUX_DATA(PORT47_FSICSPDIF_MARK, PORT47_FN2), - PINMUX_DATA(FSICISLD_MARK, PORT48_FN1), \ - PINMUX_DATA(FSIDISLD_MARK, PORT48_FN3), - PINMUX_DATA(FSIACK_MARK, PORT49_FN1), \ - PINMUX_DATA(PORT49_IRDA_OUT_MARK, PORT49_FN2, MSEL4CR_MSEL19_1), \ - PINMUX_DATA(PORT49_IROUT_MARK, PORT49_FN4), \ - PINMUX_DATA(FSIAOMC_MARK, PORT49_FN5), - PINMUX_DATA(FSIAOLR_MARK, PORT50_FN1), \ - PINMUX_DATA(BBIF2_TSYNC2_MARK, PORT50_FN2), \ - PINMUX_DATA(TPU2TO2_MARK, PORT50_FN3), \ - PINMUX_DATA(FSIAILR_MARK, PORT50_FN5), - - PINMUX_DATA(FSIAOBT_MARK, PORT51_FN1), \ - PINMUX_DATA(BBIF2_TSCK2_MARK, PORT51_FN2), \ - PINMUX_DATA(TPU2TO3_MARK, PORT51_FN3), \ - PINMUX_DATA(FSIAIBT_MARK, PORT51_FN5), - PINMUX_DATA(FSIAOSLD_MARK, PORT52_FN1), \ - PINMUX_DATA(BBIF2_TXD2_MARK, PORT52_FN2), - PINMUX_DATA(FSIASPDIF_MARK, PORT53_FN1), \ - PINMUX_DATA(PORT53_IRDA_IN_MARK, PORT53_FN2, MSEL4CR_MSEL19_1), \ - PINMUX_DATA(TPU3TO3_MARK, PORT53_FN3), \ - PINMUX_DATA(FSIBSPDIF_MARK, PORT53_FN5), \ - PINMUX_DATA(PORT53_FSICSPDIF_MARK, PORT53_FN6), - PINMUX_DATA(FSIBCK_MARK, PORT54_FN1), \ - PINMUX_DATA(PORT54_IRDA_FIRSEL_MARK, PORT54_FN2, MSEL4CR_MSEL19_1), \ - PINMUX_DATA(TPU3TO2_MARK, PORT54_FN3), \ - PINMUX_DATA(FSIBOMC_MARK, PORT54_FN5), \ - PINMUX_DATA(FSICCK_MARK, PORT54_FN6), \ - PINMUX_DATA(FSICOMC_MARK, PORT54_FN7), - PINMUX_DATA(FSIAISLD_MARK, PORT55_FN1), \ - PINMUX_DATA(TPU0TO0_MARK, PORT55_FN3), - PINMUX_DATA(A0_MARK, PORT57_FN1), \ - PINMUX_DATA(BS__MARK, PORT57_FN2), - PINMUX_DATA(A12_MARK, PORT58_FN1), \ - PINMUX_DATA(PORT58_KEYOUT7_MARK, PORT58_FN2), \ - PINMUX_DATA(TPU4TO2_MARK, PORT58_FN4), - PINMUX_DATA(A13_MARK, PORT59_FN1), \ - PINMUX_DATA(PORT59_KEYOUT6_MARK, PORT59_FN2), \ - PINMUX_DATA(TPU0TO1_MARK, PORT59_FN4), - PINMUX_DATA(A14_MARK, PORT60_FN1), \ - PINMUX_DATA(KEYOUT5_MARK, PORT60_FN2), - PINMUX_DATA(A15_MARK, PORT61_FN1), \ - PINMUX_DATA(KEYOUT4_MARK, PORT61_FN2), - PINMUX_DATA(A16_MARK, PORT62_FN1), \ - PINMUX_DATA(KEYOUT3_MARK, PORT62_FN2), \ - PINMUX_DATA(MSIOF0_SS1_MARK, PORT62_FN4, MSEL3CR_MSEL11_0), - PINMUX_DATA(A17_MARK, PORT63_FN1), \ - PINMUX_DATA(KEYOUT2_MARK, PORT63_FN2), \ - PINMUX_DATA(MSIOF0_TSYNC_MARK, PORT63_FN4, MSEL3CR_MSEL11_0), - PINMUX_DATA(A18_MARK, PORT64_FN1), \ - PINMUX_DATA(KEYOUT1_MARK, PORT64_FN2), \ - PINMUX_DATA(MSIOF0_TSCK_MARK, PORT64_FN4, MSEL3CR_MSEL11_0), - PINMUX_DATA(A19_MARK, PORT65_FN1), \ - PINMUX_DATA(KEYOUT0_MARK, PORT65_FN2), \ - PINMUX_DATA(MSIOF0_TXD_MARK, PORT65_FN4, MSEL3CR_MSEL11_0), - PINMUX_DATA(A20_MARK, PORT66_FN1), \ - PINMUX_DATA(KEYIN0_MARK, PORT66_FN2), \ - PINMUX_DATA(MSIOF0_RSCK_MARK, PORT66_FN4, MSEL3CR_MSEL11_0), - PINMUX_DATA(A21_MARK, PORT67_FN1), \ - PINMUX_DATA(KEYIN1_MARK, PORT67_FN2), \ - PINMUX_DATA(MSIOF0_RSYNC_MARK, PORT67_FN4, MSEL3CR_MSEL11_0), - PINMUX_DATA(A22_MARK, PORT68_FN1), \ - PINMUX_DATA(KEYIN2_MARK, PORT68_FN2), \ - PINMUX_DATA(MSIOF0_MCK0_MARK, PORT68_FN4, MSEL3CR_MSEL11_0), - PINMUX_DATA(A23_MARK, PORT69_FN1), \ - PINMUX_DATA(KEYIN3_MARK, PORT69_FN2), \ - PINMUX_DATA(MSIOF0_MCK1_MARK, PORT69_FN4, MSEL3CR_MSEL11_0), - PINMUX_DATA(A24_MARK, PORT70_FN1), \ - PINMUX_DATA(KEYIN4_MARK, PORT70_FN2), \ - PINMUX_DATA(MSIOF0_RXD_MARK, PORT70_FN4, MSEL3CR_MSEL11_0), - PINMUX_DATA(A25_MARK, PORT71_FN1), \ - PINMUX_DATA(KEYIN5_MARK, PORT71_FN2), \ - PINMUX_DATA(MSIOF0_SS2_MARK, PORT71_FN4, MSEL3CR_MSEL11_0), - PINMUX_DATA(A26_MARK, PORT72_FN1), \ - PINMUX_DATA(KEYIN6_MARK, PORT72_FN2), - PINMUX_DATA(KEYIN7_MARK, PORT73_FN2), - PINMUX_DATA(D0_NAF0_MARK, PORT74_FN1), - PINMUX_DATA(D1_NAF1_MARK, PORT75_FN1), - PINMUX_DATA(D2_NAF2_MARK, PORT76_FN1), - PINMUX_DATA(D3_NAF3_MARK, PORT77_FN1), - PINMUX_DATA(D4_NAF4_MARK, PORT78_FN1), - PINMUX_DATA(D5_NAF5_MARK, PORT79_FN1), - PINMUX_DATA(D6_NAF6_MARK, PORT80_FN1), - PINMUX_DATA(D7_NAF7_MARK, PORT81_FN1), - PINMUX_DATA(D8_NAF8_MARK, PORT82_FN1), - PINMUX_DATA(D9_NAF9_MARK, PORT83_FN1), - PINMUX_DATA(D10_NAF10_MARK, PORT84_FN1), - PINMUX_DATA(D11_NAF11_MARK, PORT85_FN1), - PINMUX_DATA(D12_NAF12_MARK, PORT86_FN1), - PINMUX_DATA(D13_NAF13_MARK, PORT87_FN1), - PINMUX_DATA(D14_NAF14_MARK, PORT88_FN1), - PINMUX_DATA(D15_NAF15_MARK, PORT89_FN1), - PINMUX_DATA(CS4__MARK, PORT90_FN1), - PINMUX_DATA(CS5A__MARK, PORT91_FN1), \ - PINMUX_DATA(PORT91_RDWR_MARK, PORT91_FN2), - PINMUX_DATA(CS5B__MARK, PORT92_FN1), \ - PINMUX_DATA(FCE1__MARK, PORT92_FN2), - PINMUX_DATA(CS6B__MARK, PORT93_FN1), \ - PINMUX_DATA(DACK0_MARK, PORT93_FN4), - PINMUX_DATA(FCE0__MARK, PORT94_FN1), \ - PINMUX_DATA(CS6A__MARK, PORT94_FN2), - PINMUX_DATA(WAIT__MARK, PORT95_FN1), \ - PINMUX_DATA(DREQ0_MARK, PORT95_FN2), - PINMUX_DATA(RD__FSC_MARK, PORT96_FN1), - PINMUX_DATA(WE0__FWE_MARK, PORT97_FN1), \ - PINMUX_DATA(RDWR_FWE_MARK, PORT97_FN2), - PINMUX_DATA(WE1__MARK, PORT98_FN1), - PINMUX_DATA(FRB_MARK, PORT99_FN1), - PINMUX_DATA(CKO_MARK, PORT100_FN1), - PINMUX_DATA(NBRSTOUT__MARK, PORT101_FN1), - PINMUX_DATA(NBRST__MARK, PORT102_FN1), - PINMUX_DATA(BBIF2_TXD_MARK, PORT103_FN3), - PINMUX_DATA(BBIF2_RXD_MARK, PORT104_FN3), - PINMUX_DATA(BBIF2_SYNC_MARK, PORT105_FN3), - PINMUX_DATA(BBIF2_SCK_MARK, PORT106_FN3), - PINMUX_DATA(SCIFA3_CTS__MARK, PORT107_FN3), \ - PINMUX_DATA(MFG3_IN2_MARK, PORT107_FN4), - PINMUX_DATA(SCIFA3_RXD_MARK, PORT108_FN3), \ - PINMUX_DATA(MFG3_IN1_MARK, PORT108_FN4), - PINMUX_DATA(BBIF1_SS2_MARK, PORT109_FN2), \ - PINMUX_DATA(SCIFA3_RTS__MARK, PORT109_FN3), \ - PINMUX_DATA(MFG3_OUT1_MARK, PORT109_FN4), - PINMUX_DATA(SCIFA3_TXD_MARK, PORT110_FN3), - PINMUX_DATA(HSI_RX_DATA_MARK, PORT111_FN1), \ - PINMUX_DATA(BBIF1_RXD_MARK, PORT111_FN3), - PINMUX_DATA(HSI_TX_WAKE_MARK, PORT112_FN1), \ - PINMUX_DATA(BBIF1_TSCK_MARK, PORT112_FN3), - PINMUX_DATA(HSI_TX_DATA_MARK, PORT113_FN1), \ - PINMUX_DATA(BBIF1_TSYNC_MARK, PORT113_FN3), - PINMUX_DATA(HSI_TX_READY_MARK, PORT114_FN1), \ - PINMUX_DATA(BBIF1_TXD_MARK, PORT114_FN3), - PINMUX_DATA(HSI_RX_READY_MARK, PORT115_FN1), \ - PINMUX_DATA(BBIF1_RSCK_MARK, PORT115_FN3), \ - PINMUX_DATA(PORT115_I2C_SCL2_MARK, PORT115_FN5, MSEL2CR_MSEL17_1), \ - PINMUX_DATA(PORT115_I2C_SCL3_MARK, PORT115_FN6, MSEL2CR_MSEL19_1), - PINMUX_DATA(HSI_RX_WAKE_MARK, PORT116_FN1), \ - PINMUX_DATA(BBIF1_RSYNC_MARK, PORT116_FN3), \ - PINMUX_DATA(PORT116_I2C_SDA2_MARK, PORT116_FN5, MSEL2CR_MSEL17_1), \ - PINMUX_DATA(PORT116_I2C_SDA3_MARK, PORT116_FN6, MSEL2CR_MSEL19_1), - PINMUX_DATA(HSI_RX_FLAG_MARK, PORT117_FN1), \ - PINMUX_DATA(BBIF1_SS1_MARK, PORT117_FN2), \ - PINMUX_DATA(BBIF1_FLOW_MARK, PORT117_FN3), - PINMUX_DATA(HSI_TX_FLAG_MARK, PORT118_FN1), - PINMUX_DATA(VIO_VD_MARK, PORT128_FN1), \ - PINMUX_DATA(PORT128_LCD2VSYN_MARK, PORT128_FN4, MSEL3CR_MSEL2_0), \ - PINMUX_DATA(VIO2_VD_MARK, PORT128_FN6, MSEL4CR_MSEL27_0), \ - PINMUX_DATA(LCD2D0_MARK, PORT128_FN7), - - PINMUX_DATA(VIO_HD_MARK, PORT129_FN1), \ - PINMUX_DATA(PORT129_LCD2HSYN_MARK, PORT129_FN4), \ - PINMUX_DATA(PORT129_LCD2CS__MARK, PORT129_FN5), \ - PINMUX_DATA(VIO2_HD_MARK, PORT129_FN6, MSEL4CR_MSEL27_0), \ - PINMUX_DATA(LCD2D1_MARK, PORT129_FN7), - PINMUX_DATA(VIO_D0_MARK, PORT130_FN1), \ - PINMUX_DATA(PORT130_MSIOF2_RXD_MARK, PORT130_FN3, MSEL4CR_MSEL11_0, - MSEL4CR_MSEL10_1), \ - PINMUX_DATA(LCD2D10_MARK, PORT130_FN7), - PINMUX_DATA(VIO_D1_MARK, PORT131_FN1), \ - PINMUX_DATA(PORT131_KEYOUT6_MARK, PORT131_FN2), \ - PINMUX_DATA(PORT131_MSIOF2_SS1_MARK, PORT131_FN3), \ - PINMUX_DATA(PORT131_KEYOUT11_MARK, PORT131_FN4), \ - PINMUX_DATA(LCD2D11_MARK, PORT131_FN7), - PINMUX_DATA(VIO_D2_MARK, PORT132_FN1), \ - PINMUX_DATA(PORT132_KEYOUT7_MARK, PORT132_FN2), \ - PINMUX_DATA(PORT132_MSIOF2_SS2_MARK, PORT132_FN3), \ - PINMUX_DATA(PORT132_KEYOUT10_MARK, PORT132_FN4), \ - PINMUX_DATA(LCD2D12_MARK, PORT132_FN7), - PINMUX_DATA(VIO_D3_MARK, PORT133_FN1), \ - PINMUX_DATA(MSIOF2_TSYNC_MARK, PORT133_FN3, MSEL4CR_MSEL11_0), \ - PINMUX_DATA(LCD2D13_MARK, PORT133_FN7), - PINMUX_DATA(VIO_D4_MARK, PORT134_FN1), \ - PINMUX_DATA(MSIOF2_TXD_MARK, PORT134_FN3, MSEL4CR_MSEL11_0), \ - PINMUX_DATA(LCD2D14_MARK, PORT134_FN7), - PINMUX_DATA(VIO_D5_MARK, PORT135_FN1), \ - PINMUX_DATA(MSIOF2_TSCK_MARK, PORT135_FN3, MSEL4CR_MSEL11_0), \ - PINMUX_DATA(LCD2D15_MARK, PORT135_FN7), - PINMUX_DATA(VIO_D6_MARK, PORT136_FN1), \ - PINMUX_DATA(PORT136_KEYOUT8_MARK, PORT136_FN2), \ - PINMUX_DATA(LCD2D16_MARK, PORT136_FN7), - PINMUX_DATA(VIO_D7_MARK, PORT137_FN1), \ - PINMUX_DATA(PORT137_KEYOUT9_MARK, PORT137_FN2), \ - PINMUX_DATA(LCD2D17_MARK, PORT137_FN7), - PINMUX_DATA(VIO_D8_MARK, PORT138_FN1), \ - PINMUX_DATA(PORT138_KEYOUT8_MARK, PORT138_FN2), \ - PINMUX_DATA(VIO2_D0_MARK, PORT138_FN6), \ - PINMUX_DATA(LCD2D6_MARK, PORT138_FN7), - PINMUX_DATA(VIO_D9_MARK, PORT139_FN1), \ - PINMUX_DATA(PORT139_KEYOUT9_MARK, PORT139_FN2), \ - PINMUX_DATA(VIO2_D1_MARK, PORT139_FN6), \ - PINMUX_DATA(LCD2D7_MARK, PORT139_FN7), - PINMUX_DATA(VIO_D10_MARK, PORT140_FN1), \ - PINMUX_DATA(TPU0TO2_MARK, PORT140_FN4), \ - PINMUX_DATA(VIO2_D2_MARK, PORT140_FN6), \ - PINMUX_DATA(LCD2D8_MARK, PORT140_FN7), - PINMUX_DATA(VIO_D11_MARK, PORT141_FN1), \ - PINMUX_DATA(TPU0TO3_MARK, PORT141_FN4), \ - PINMUX_DATA(VIO2_D3_MARK, PORT141_FN6), \ - PINMUX_DATA(LCD2D9_MARK, PORT141_FN7), - PINMUX_DATA(VIO_D12_MARK, PORT142_FN1), \ - PINMUX_DATA(PORT142_KEYOUT10_MARK, PORT142_FN2), \ - PINMUX_DATA(VIO2_D4_MARK, PORT142_FN6), \ - PINMUX_DATA(LCD2D2_MARK, PORT142_FN7), - PINMUX_DATA(VIO_D13_MARK, PORT143_FN1), \ - PINMUX_DATA(PORT143_KEYOUT11_MARK, PORT143_FN2), \ - PINMUX_DATA(PORT143_KEYOUT6_MARK, PORT143_FN3), \ - PINMUX_DATA(VIO2_D5_MARK, PORT143_FN6), \ - PINMUX_DATA(LCD2D3_MARK, PORT143_FN7), - PINMUX_DATA(VIO_D14_MARK, PORT144_FN1), \ - PINMUX_DATA(PORT144_KEYOUT7_MARK, PORT144_FN2), \ - PINMUX_DATA(VIO2_D6_MARK, PORT144_FN6), \ - PINMUX_DATA(LCD2D4_MARK, PORT144_FN7), - PINMUX_DATA(VIO_D15_MARK, PORT145_FN1), \ - PINMUX_DATA(TPU1TO3_MARK, PORT145_FN3), \ - PINMUX_DATA(PORT145_LCD2DISP_MARK, PORT145_FN4), \ - PINMUX_DATA(PORT145_LCD2RS_MARK, PORT145_FN5), \ - PINMUX_DATA(VIO2_D7_MARK, PORT145_FN6), \ - PINMUX_DATA(LCD2D5_MARK, PORT145_FN7), - PINMUX_DATA(VIO_CLK_MARK, PORT146_FN1), \ - PINMUX_DATA(LCD2DCK_MARK, PORT146_FN4), \ - PINMUX_DATA(PORT146_LCD2WR__MARK, PORT146_FN5), \ - PINMUX_DATA(VIO2_CLK_MARK, PORT146_FN6, MSEL4CR_MSEL27_0), \ - PINMUX_DATA(LCD2D18_MARK, PORT146_FN7), - PINMUX_DATA(VIO_FIELD_MARK, PORT147_FN1), \ - PINMUX_DATA(LCD2RD__MARK, PORT147_FN4), \ - PINMUX_DATA(VIO2_FIELD_MARK, PORT147_FN6, MSEL4CR_MSEL27_0), \ - PINMUX_DATA(LCD2D19_MARK, PORT147_FN7), - PINMUX_DATA(VIO_CKO_MARK, PORT148_FN1), - PINMUX_DATA(A27_MARK, PORT149_FN1), \ - PINMUX_DATA(PORT149_RDWR_MARK, PORT149_FN2), \ - PINMUX_DATA(MFG0_IN1_MARK, PORT149_FN3), \ - PINMUX_DATA(PORT149_KEYOUT9_MARK, PORT149_FN4), - PINMUX_DATA(MFG0_IN2_MARK, PORT150_FN3), - PINMUX_DATA(TS_SPSYNC3_MARK, PORT151_FN4), \ - PINMUX_DATA(MSIOF2_RSCK_MARK, PORT151_FN5), - PINMUX_DATA(TS_SDAT3_MARK, PORT152_FN4), \ - PINMUX_DATA(MSIOF2_RSYNC_MARK, PORT152_FN5), - PINMUX_DATA(TPU1TO2_MARK, PORT153_FN3), \ - PINMUX_DATA(TS_SDEN3_MARK, PORT153_FN4), \ - PINMUX_DATA(PORT153_MSIOF2_SS1_MARK, PORT153_FN5), - PINMUX_DATA(SCIFA2_TXD1_MARK, PORT154_FN2, MSEL3CR_MSEL9_0), \ - PINMUX_DATA(MSIOF2_MCK0_MARK, PORT154_FN5), - PINMUX_DATA(SCIFA2_RXD1_MARK, PORT155_FN2, MSEL3CR_MSEL9_0), \ - PINMUX_DATA(MSIOF2_MCK1_MARK, PORT155_FN5), - PINMUX_DATA(SCIFA2_RTS1__MARK, PORT156_FN2, MSEL3CR_MSEL9_0), \ - PINMUX_DATA(PORT156_MSIOF2_SS2_MARK, PORT156_FN5), - PINMUX_DATA(SCIFA2_CTS1__MARK, PORT157_FN2, MSEL3CR_MSEL9_0), \ - PINMUX_DATA(PORT157_MSIOF2_RXD_MARK, PORT157_FN5, MSEL4CR_MSEL11_0, - MSEL4CR_MSEL10_0), - PINMUX_DATA(DINT__MARK, PORT158_FN1), \ - PINMUX_DATA(SCIFA2_SCK1_MARK, PORT158_FN2, MSEL3CR_MSEL9_0), \ - PINMUX_DATA(TS_SCK3_MARK, PORT158_FN4), - PINMUX_DATA(PORT159_SCIFB_SCK_MARK, PORT159_FN1, MSEL4CR_MSEL22_0), \ - PINMUX_DATA(PORT159_SCIFA5_SCK_MARK, PORT159_FN2, MSEL4CR_MSEL21_1), \ - PINMUX_DATA(NMI_MARK, PORT159_FN3), - PINMUX_DATA(PORT160_SCIFB_TXD_MARK, PORT160_FN1, MSEL4CR_MSEL22_0), \ - PINMUX_DATA(PORT160_SCIFA5_TXD_MARK, PORT160_FN2, MSEL4CR_MSEL21_1), - PINMUX_DATA(PORT161_SCIFB_CTS__MARK, PORT161_FN1, MSEL4CR_MSEL22_0), \ - PINMUX_DATA(PORT161_SCIFA5_CTS__MARK, PORT161_FN2, MSEL4CR_MSEL21_1), - PINMUX_DATA(PORT162_SCIFB_RXD_MARK, PORT162_FN1, MSEL4CR_MSEL22_0), \ - PINMUX_DATA(PORT162_SCIFA5_RXD_MARK, PORT162_FN2, MSEL4CR_MSEL21_1), - PINMUX_DATA(PORT163_SCIFB_RTS__MARK, PORT163_FN1, MSEL4CR_MSEL22_0), \ - PINMUX_DATA(PORT163_SCIFA5_RTS__MARK, PORT163_FN2, MSEL4CR_MSEL21_1), \ - PINMUX_DATA(TPU3TO0_MARK, PORT163_FN5), - PINMUX_DATA(LCDD0_MARK, PORT192_FN1), - PINMUX_DATA(LCDD1_MARK, PORT193_FN1), \ - PINMUX_DATA(PORT193_SCIFA5_CTS__MARK, PORT193_FN3, MSEL4CR_MSEL21_0, - MSEL4CR_MSEL20_1), \ - PINMUX_DATA(BBIF2_TSYNC1_MARK, PORT193_FN5), - PINMUX_DATA(LCDD2_MARK, PORT194_FN1), \ - PINMUX_DATA(PORT194_SCIFA5_RTS__MARK, PORT194_FN3, MSEL4CR_MSEL21_0, - MSEL4CR_MSEL20_1), \ - PINMUX_DATA(BBIF2_TSCK1_MARK, PORT194_FN5), - PINMUX_DATA(LCDD3_MARK, PORT195_FN1), \ - PINMUX_DATA(PORT195_SCIFA5_RXD_MARK, PORT195_FN3, MSEL4CR_MSEL21_0, - MSEL4CR_MSEL20_1), \ - PINMUX_DATA(BBIF2_TXD1_MARK, PORT195_FN5), - PINMUX_DATA(LCDD4_MARK, PORT196_FN1), \ - PINMUX_DATA(PORT196_SCIFA5_TXD_MARK, PORT196_FN3, MSEL4CR_MSEL21_0, - MSEL4CR_MSEL20_1), - PINMUX_DATA(LCDD5_MARK, PORT197_FN1), \ - PINMUX_DATA(PORT197_SCIFA5_SCK_MARK, PORT197_FN3, MSEL4CR_MSEL21_0, - MSEL4CR_MSEL20_1), \ - PINMUX_DATA(MFG2_OUT2_MARK, PORT197_FN5), \ - PINMUX_DATA(TPU2TO1_MARK, PORT197_FN7), - PINMUX_DATA(LCDD6_MARK, PORT198_FN1), - PINMUX_DATA(LCDD7_MARK, PORT199_FN1), \ - PINMUX_DATA(TPU4TO1_MARK, PORT199_FN2), \ - PINMUX_DATA(MFG4_OUT2_MARK, PORT199_FN5), - PINMUX_DATA(LCDD8_MARK, PORT200_FN1), \ - PINMUX_DATA(D16_MARK, PORT200_FN6), - PINMUX_DATA(LCDD9_MARK, PORT201_FN1), \ - PINMUX_DATA(D17_MARK, PORT201_FN6), - PINMUX_DATA(LCDD10_MARK, PORT202_FN1), \ - PINMUX_DATA(D18_MARK, PORT202_FN6), - PINMUX_DATA(LCDD11_MARK, PORT203_FN1), \ - PINMUX_DATA(D19_MARK, PORT203_FN6), - PINMUX_DATA(LCDD12_MARK, PORT204_FN1), \ - PINMUX_DATA(D20_MARK, PORT204_FN6), - PINMUX_DATA(LCDD13_MARK, PORT205_FN1), \ - PINMUX_DATA(D21_MARK, PORT205_FN6), - PINMUX_DATA(LCDD14_MARK, PORT206_FN1), \ - PINMUX_DATA(D22_MARK, PORT206_FN6), - PINMUX_DATA(LCDD15_MARK, PORT207_FN1), \ - PINMUX_DATA(PORT207_MSIOF0L_SS1_MARK, PORT207_FN2, MSEL3CR_MSEL11_1), \ - PINMUX_DATA(D23_MARK, PORT207_FN6), - PINMUX_DATA(LCDD16_MARK, PORT208_FN1), \ - PINMUX_DATA(PORT208_MSIOF0L_SS2_MARK, PORT208_FN2, MSEL3CR_MSEL11_1), \ - PINMUX_DATA(D24_MARK, PORT208_FN6), - PINMUX_DATA(LCDD17_MARK, PORT209_FN1), \ - PINMUX_DATA(D25_MARK, PORT209_FN6), - PINMUX_DATA(LCDD18_MARK, PORT210_FN1), \ - PINMUX_DATA(DREQ2_MARK, PORT210_FN2), \ - PINMUX_DATA(PORT210_MSIOF0L_SS1_MARK, PORT210_FN5, MSEL3CR_MSEL11_1), \ - PINMUX_DATA(D26_MARK, PORT210_FN6), - PINMUX_DATA(LCDD19_MARK, PORT211_FN1), \ - PINMUX_DATA(PORT211_MSIOF0L_SS2_MARK, PORT211_FN5, MSEL3CR_MSEL11_1), \ - PINMUX_DATA(D27_MARK, PORT211_FN6), - PINMUX_DATA(LCDD20_MARK, PORT212_FN1), \ - PINMUX_DATA(TS_SPSYNC1_MARK, PORT212_FN2), \ - PINMUX_DATA(MSIOF0L_MCK0_MARK, PORT212_FN5, MSEL3CR_MSEL11_1), \ - PINMUX_DATA(D28_MARK, PORT212_FN6), - PINMUX_DATA(LCDD21_MARK, PORT213_FN1), \ - PINMUX_DATA(TS_SDAT1_MARK, PORT213_FN2), \ - PINMUX_DATA(MSIOF0L_MCK1_MARK, PORT213_FN5, MSEL3CR_MSEL11_1), \ - PINMUX_DATA(D29_MARK, PORT213_FN6), - PINMUX_DATA(LCDD22_MARK, PORT214_FN1), \ - PINMUX_DATA(TS_SDEN1_MARK, PORT214_FN2), \ - PINMUX_DATA(MSIOF0L_RSCK_MARK, PORT214_FN5, MSEL3CR_MSEL11_1), \ - PINMUX_DATA(D30_MARK, PORT214_FN6), - PINMUX_DATA(LCDD23_MARK, PORT215_FN1), \ - PINMUX_DATA(TS_SCK1_MARK, PORT215_FN2), \ - PINMUX_DATA(MSIOF0L_RSYNC_MARK, PORT215_FN5, MSEL3CR_MSEL11_1), \ - PINMUX_DATA(D31_MARK, PORT215_FN6), - PINMUX_DATA(LCDDCK_MARK, PORT216_FN1), \ - PINMUX_DATA(LCDWR__MARK, PORT216_FN2), - PINMUX_DATA(LCDRD__MARK, PORT217_FN1), \ - PINMUX_DATA(DACK2_MARK, PORT217_FN2), \ - PINMUX_DATA(PORT217_LCD2RS_MARK, PORT217_FN3), \ - PINMUX_DATA(MSIOF0L_TSYNC_MARK, PORT217_FN5, MSEL3CR_MSEL11_1), \ - PINMUX_DATA(VIO2_FIELD3_MARK, PORT217_FN6, MSEL4CR_MSEL27_1, - MSEL4CR_MSEL26_1), \ - PINMUX_DATA(PORT217_LCD2DISP_MARK, PORT217_FN7), - PINMUX_DATA(LCDHSYN_MARK, PORT218_FN1), \ - PINMUX_DATA(LCDCS__MARK, PORT218_FN2), \ - PINMUX_DATA(LCDCS2__MARK, PORT218_FN3), \ - PINMUX_DATA(DACK3_MARK, PORT218_FN4), \ - PINMUX_DATA(PORT218_VIO_CKOR_MARK, PORT218_FN5), - PINMUX_DATA(LCDDISP_MARK, PORT219_FN1), \ - PINMUX_DATA(LCDRS_MARK, PORT219_FN2), \ - PINMUX_DATA(PORT219_LCD2WR__MARK, PORT219_FN3), \ - PINMUX_DATA(DREQ3_MARK, PORT219_FN4), \ - PINMUX_DATA(MSIOF0L_TSCK_MARK, PORT219_FN5, MSEL3CR_MSEL11_1), \ - PINMUX_DATA(VIO2_CLK3_MARK, PORT219_FN6, MSEL4CR_MSEL27_1, - MSEL4CR_MSEL26_1), \ - PINMUX_DATA(LCD2DCK_2_MARK, PORT219_FN7), - PINMUX_DATA(LCDVSYN_MARK, PORT220_FN1), \ - PINMUX_DATA(LCDVSYN2_MARK, PORT220_FN2), - PINMUX_DATA(LCDLCLK_MARK, PORT221_FN1), \ - PINMUX_DATA(DREQ1_MARK, PORT221_FN2), \ - PINMUX_DATA(PORT221_LCD2CS__MARK, PORT221_FN3), \ - PINMUX_DATA(PWEN_MARK, PORT221_FN4), \ - PINMUX_DATA(MSIOF0L_RXD_MARK, PORT221_FN5, MSEL3CR_MSEL11_1), \ - PINMUX_DATA(VIO2_HD3_MARK, PORT221_FN6, MSEL4CR_MSEL27_1, - MSEL4CR_MSEL26_1), \ - PINMUX_DATA(PORT221_LCD2HSYN_MARK, PORT221_FN7), - PINMUX_DATA(LCDDON_MARK, PORT222_FN1), \ - PINMUX_DATA(LCDDON2_MARK, PORT222_FN2), \ - PINMUX_DATA(DACK1_MARK, PORT222_FN3), \ - PINMUX_DATA(OVCN_MARK, PORT222_FN4), \ - PINMUX_DATA(MSIOF0L_TXD_MARK, PORT222_FN5, MSEL3CR_MSEL11_1), \ - PINMUX_DATA(VIO2_VD3_MARK, PORT222_FN6, MSEL4CR_MSEL27_1, - MSEL4CR_MSEL26_1), \ - PINMUX_DATA(PORT222_LCD2VSYN_MARK, PORT222_FN7, MSEL3CR_MSEL2_1), - - PINMUX_DATA(SCIFA1_TXD_MARK, PORT225_FN2), \ - PINMUX_DATA(OVCN2_MARK, PORT225_FN4), - PINMUX_DATA(EXTLP_MARK, PORT226_FN1), \ - PINMUX_DATA(SCIFA1_SCK_MARK, PORT226_FN2), \ - PINMUX_DATA(PORT226_VIO_CKO2_MARK, PORT226_FN5), - PINMUX_DATA(SCIFA1_RTS__MARK, PORT227_FN2), \ - PINMUX_DATA(IDIN_MARK, PORT227_FN4), - PINMUX_DATA(SCIFA1_RXD_MARK, PORT228_FN2), - PINMUX_DATA(SCIFA1_CTS__MARK, PORT229_FN2), \ - PINMUX_DATA(MFG1_IN1_MARK, PORT229_FN3), - PINMUX_DATA(MSIOF1_TXD_MARK, PORT230_FN1), \ - PINMUX_DATA(SCIFA2_TXD2_MARK, PORT230_FN2, MSEL3CR_MSEL9_1), - PINMUX_DATA(MSIOF1_TSYNC_MARK, PORT231_FN1), \ - PINMUX_DATA(SCIFA2_CTS2__MARK, PORT231_FN2, MSEL3CR_MSEL9_1), - PINMUX_DATA(MSIOF1_TSCK_MARK, PORT232_FN1), \ - PINMUX_DATA(SCIFA2_SCK2_MARK, PORT232_FN2, MSEL3CR_MSEL9_1), - PINMUX_DATA(MSIOF1_RXD_MARK, PORT233_FN1), \ - PINMUX_DATA(SCIFA2_RXD2_MARK, PORT233_FN2, MSEL3CR_MSEL9_1), - PINMUX_DATA(MSIOF1_RSCK_MARK, PORT234_FN1), \ - PINMUX_DATA(SCIFA2_RTS2__MARK, PORT234_FN2, MSEL3CR_MSEL9_1), \ - PINMUX_DATA(VIO2_CLK2_MARK, PORT234_FN6, MSEL4CR_MSEL27_1, - MSEL4CR_MSEL26_0), \ - PINMUX_DATA(LCD2D20_MARK, PORT234_FN7), - PINMUX_DATA(MSIOF1_RSYNC_MARK, PORT235_FN1), \ - PINMUX_DATA(MFG1_IN2_MARK, PORT235_FN3), \ - PINMUX_DATA(VIO2_VD2_MARK, PORT235_FN6, MSEL4CR_MSEL27_1, - MSEL4CR_MSEL26_0), \ - PINMUX_DATA(LCD2D21_MARK, PORT235_FN7), - PINMUX_DATA(MSIOF1_MCK0_MARK, PORT236_FN1), \ - PINMUX_DATA(PORT236_I2C_SDA2_MARK, PORT236_FN2, MSEL2CR_MSEL17_0, - MSEL2CR_MSEL16_0), - PINMUX_DATA(MSIOF1_MCK1_MARK, PORT237_FN1), \ - PINMUX_DATA(PORT237_I2C_SCL2_MARK, PORT237_FN2, MSEL2CR_MSEL17_0, - MSEL2CR_MSEL16_0), - PINMUX_DATA(MSIOF1_SS1_MARK, PORT238_FN1), \ - PINMUX_DATA(VIO2_FIELD2_MARK, PORT238_FN6, MSEL4CR_MSEL27_1, - MSEL4CR_MSEL26_0), \ - PINMUX_DATA(LCD2D22_MARK, PORT238_FN7), - PINMUX_DATA(MSIOF1_SS2_MARK, PORT239_FN1), \ - PINMUX_DATA(VIO2_HD2_MARK, PORT239_FN6, MSEL4CR_MSEL27_1, - MSEL4CR_MSEL26_0), \ - PINMUX_DATA(LCD2D23_MARK, PORT239_FN7), - PINMUX_DATA(SCIFA6_TXD_MARK, PORT240_FN1), - PINMUX_DATA(PORT241_IRDA_OUT_MARK, PORT241_FN1, MSEL4CR_MSEL19_0), \ - PINMUX_DATA(PORT241_IROUT_MARK, PORT241_FN2), \ - PINMUX_DATA(MFG4_OUT1_MARK, PORT241_FN3), \ - PINMUX_DATA(TPU4TO0_MARK, PORT241_FN4), - PINMUX_DATA(PORT242_IRDA_IN_MARK, PORT242_FN1, MSEL4CR_MSEL19_0), \ - PINMUX_DATA(MFG4_IN2_MARK, PORT242_FN3), - PINMUX_DATA(PORT243_IRDA_FIRSEL_MARK, PORT243_FN1, MSEL4CR_MSEL19_0), \ - PINMUX_DATA(PORT243_VIO_CKO2_MARK, PORT243_FN2), - PINMUX_DATA(PORT244_SCIFA5_CTS__MARK, PORT244_FN1, MSEL4CR_MSEL21_0, - MSEL4CR_MSEL20_0), \ - PINMUX_DATA(MFG2_IN1_MARK, PORT244_FN2), \ - PINMUX_DATA(PORT244_SCIFB_CTS__MARK, PORT244_FN3, MSEL4CR_MSEL22_1), \ - PINMUX_DATA(MSIOF2R_RXD_MARK, PORT244_FN7, MSEL4CR_MSEL11_1), - PINMUX_DATA(PORT245_SCIFA5_RTS__MARK, PORT245_FN1, MSEL4CR_MSEL21_0, - MSEL4CR_MSEL20_0), \ - PINMUX_DATA(MFG2_IN2_MARK, PORT245_FN2), \ - PINMUX_DATA(PORT245_SCIFB_RTS__MARK, PORT245_FN3, MSEL4CR_MSEL22_1), \ - PINMUX_DATA(MSIOF2R_TXD_MARK, PORT245_FN7, MSEL4CR_MSEL11_1), - PINMUX_DATA(PORT246_SCIFA5_RXD_MARK, PORT246_FN1, MSEL4CR_MSEL21_0, - MSEL4CR_MSEL20_0), \ - PINMUX_DATA(MFG1_OUT1_MARK, PORT246_FN2), \ - PINMUX_DATA(PORT246_SCIFB_RXD_MARK, PORT246_FN3, MSEL4CR_MSEL22_1), \ - PINMUX_DATA(TPU1TO0_MARK, PORT246_FN4), - PINMUX_DATA(PORT247_SCIFA5_TXD_MARK, PORT247_FN1, MSEL4CR_MSEL21_0, - MSEL4CR_MSEL20_0), \ - PINMUX_DATA(MFG3_OUT2_MARK, PORT247_FN2), \ - PINMUX_DATA(PORT247_SCIFB_TXD_MARK, PORT247_FN3, MSEL4CR_MSEL22_1), \ - PINMUX_DATA(TPU3TO1_MARK, PORT247_FN4), - PINMUX_DATA(PORT248_SCIFA5_SCK_MARK, PORT248_FN1, MSEL4CR_MSEL21_0, - MSEL4CR_MSEL20_0), \ - PINMUX_DATA(MFG2_OUT1_MARK, PORT248_FN2), \ - PINMUX_DATA(PORT248_SCIFB_SCK_MARK, PORT248_FN3, MSEL4CR_MSEL22_1), \ - PINMUX_DATA(TPU2TO0_MARK, PORT248_FN4), \ - PINMUX_DATA(PORT248_I2C_SCL3_MARK, PORT248_FN5, MSEL2CR_MSEL19_0, - MSEL2CR_MSEL18_0), \ - PINMUX_DATA(MSIOF2R_TSCK_MARK, PORT248_FN7, MSEL4CR_MSEL11_1), - PINMUX_DATA(PORT249_IROUT_MARK, PORT249_FN1), \ - PINMUX_DATA(MFG4_IN1_MARK, PORT249_FN2), \ - PINMUX_DATA(PORT249_I2C_SDA3_MARK, PORT249_FN5, MSEL2CR_MSEL19_0, - MSEL2CR_MSEL18_0), \ - PINMUX_DATA(MSIOF2R_TSYNC_MARK, PORT249_FN7, MSEL4CR_MSEL11_1), - PINMUX_DATA(SDHICLK0_MARK, PORT250_FN1), - PINMUX_DATA(SDHICD0_MARK, PORT251_FN1), - PINMUX_DATA(SDHID0_0_MARK, PORT252_FN1), - PINMUX_DATA(SDHID0_1_MARK, PORT253_FN1), - PINMUX_DATA(SDHID0_2_MARK, PORT254_FN1), - PINMUX_DATA(SDHID0_3_MARK, PORT255_FN1), - PINMUX_DATA(SDHICMD0_MARK, PORT256_FN1), - PINMUX_DATA(SDHIWP0_MARK, PORT257_FN1), - PINMUX_DATA(SDHICLK1_MARK, PORT258_FN1), - PINMUX_DATA(SDHID1_0_MARK, PORT259_FN1), \ - PINMUX_DATA(TS_SPSYNC2_MARK, PORT259_FN3), - PINMUX_DATA(SDHID1_1_MARK, PORT260_FN1), \ - PINMUX_DATA(TS_SDAT2_MARK, PORT260_FN3), - PINMUX_DATA(SDHID1_2_MARK, PORT261_FN1), \ - PINMUX_DATA(TS_SDEN2_MARK, PORT261_FN3), - PINMUX_DATA(SDHID1_3_MARK, PORT262_FN1), \ - PINMUX_DATA(TS_SCK2_MARK, PORT262_FN3), - PINMUX_DATA(SDHICMD1_MARK, PORT263_FN1), - PINMUX_DATA(SDHICLK2_MARK, PORT264_FN1), - PINMUX_DATA(SDHID2_0_MARK, PORT265_FN1), \ - PINMUX_DATA(TS_SPSYNC4_MARK, PORT265_FN3), - PINMUX_DATA(SDHID2_1_MARK, PORT266_FN1), \ - PINMUX_DATA(TS_SDAT4_MARK, PORT266_FN3), - PINMUX_DATA(SDHID2_2_MARK, PORT267_FN1), \ - PINMUX_DATA(TS_SDEN4_MARK, PORT267_FN3), - PINMUX_DATA(SDHID2_3_MARK, PORT268_FN1), \ - PINMUX_DATA(TS_SCK4_MARK, PORT268_FN3), - PINMUX_DATA(SDHICMD2_MARK, PORT269_FN1), - PINMUX_DATA(MMCCLK0_MARK, PORT270_FN1, MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCD0_0_MARK, PORT271_FN1, PORT271_IN_PU, - MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCD0_1_MARK, PORT272_FN1, PORT272_IN_PU, - MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCD0_2_MARK, PORT273_FN1, PORT273_IN_PU, - MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCD0_3_MARK, PORT274_FN1, PORT274_IN_PU, - MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCD0_4_MARK, PORT275_FN1, PORT275_IN_PU, - MSEL4CR_MSEL15_0), \ - PINMUX_DATA(TS_SPSYNC5_MARK, PORT275_FN3), - PINMUX_DATA(MMCD0_5_MARK, PORT276_FN1, PORT276_IN_PU, - MSEL4CR_MSEL15_0), \ - PINMUX_DATA(TS_SDAT5_MARK, PORT276_FN3), - PINMUX_DATA(MMCD0_6_MARK, PORT277_FN1, PORT277_IN_PU, - MSEL4CR_MSEL15_0), \ - PINMUX_DATA(TS_SDEN5_MARK, PORT277_FN3), - PINMUX_DATA(MMCD0_7_MARK, PORT278_FN1, PORT278_IN_PU, - MSEL4CR_MSEL15_0), \ - PINMUX_DATA(TS_SCK5_MARK, PORT278_FN3), - PINMUX_DATA(MMCCMD0_MARK, PORT279_FN1, PORT279_IN_PU, - MSEL4CR_MSEL15_0), - PINMUX_DATA(RESETOUTS__MARK, PORT281_FN1), \ - PINMUX_DATA(EXTAL2OUT_MARK, PORT281_FN2), - PINMUX_DATA(MCP_WAIT__MCP_FRB_MARK, PORT288_FN1), - PINMUX_DATA(MCP_CKO_MARK, PORT289_FN1), \ - PINMUX_DATA(MMCCLK1_MARK, PORT289_FN2, MSEL4CR_MSEL15_1), - PINMUX_DATA(MCP_D15_MCP_NAF15_MARK, PORT290_FN1), - PINMUX_DATA(MCP_D14_MCP_NAF14_MARK, PORT291_FN1), - PINMUX_DATA(MCP_D13_MCP_NAF13_MARK, PORT292_FN1), - PINMUX_DATA(MCP_D12_MCP_NAF12_MARK, PORT293_FN1), - PINMUX_DATA(MCP_D11_MCP_NAF11_MARK, PORT294_FN1), - PINMUX_DATA(MCP_D10_MCP_NAF10_MARK, PORT295_FN1), - PINMUX_DATA(MCP_D9_MCP_NAF9_MARK, PORT296_FN1), - PINMUX_DATA(MCP_D8_MCP_NAF8_MARK, PORT297_FN1), \ - PINMUX_DATA(MMCCMD1_MARK, PORT297_FN2, MSEL4CR_MSEL15_1), - PINMUX_DATA(MCP_D7_MCP_NAF7_MARK, PORT298_FN1), \ - PINMUX_DATA(MMCD1_7_MARK, PORT298_FN2, MSEL4CR_MSEL15_1), - - PINMUX_DATA(MCP_D6_MCP_NAF6_MARK, PORT299_FN1), \ - PINMUX_DATA(MMCD1_6_MARK, PORT299_FN2, MSEL4CR_MSEL15_1), - PINMUX_DATA(MCP_D5_MCP_NAF5_MARK, PORT300_FN1), \ - PINMUX_DATA(MMCD1_5_MARK, PORT300_FN2, MSEL4CR_MSEL15_1), - PINMUX_DATA(MCP_D4_MCP_NAF4_MARK, PORT301_FN1), \ - PINMUX_DATA(MMCD1_4_MARK, PORT301_FN2, MSEL4CR_MSEL15_1), - PINMUX_DATA(MCP_D3_MCP_NAF3_MARK, PORT302_FN1), \ - PINMUX_DATA(MMCD1_3_MARK, PORT302_FN2, MSEL4CR_MSEL15_1), - PINMUX_DATA(MCP_D2_MCP_NAF2_MARK, PORT303_FN1), \ - PINMUX_DATA(MMCD1_2_MARK, PORT303_FN2, MSEL4CR_MSEL15_1), - PINMUX_DATA(MCP_D1_MCP_NAF1_MARK, PORT304_FN1), \ - PINMUX_DATA(MMCD1_1_MARK, PORT304_FN2, MSEL4CR_MSEL15_1), - PINMUX_DATA(MCP_D0_MCP_NAF0_MARK, PORT305_FN1), \ - PINMUX_DATA(MMCD1_0_MARK, PORT305_FN2, MSEL4CR_MSEL15_1), - PINMUX_DATA(MCP_NBRSTOUT__MARK, PORT306_FN1), - PINMUX_DATA(MCP_WE0__MCP_FWE_MARK, PORT309_FN1), \ - PINMUX_DATA(MCP_RDWR_MCP_FWE_MARK, PORT309_FN2), - - /* MSEL2 special cases */ - PINMUX_DATA(TSIF2_TS_XX1_MARK, MSEL2CR_MSEL14_0, MSEL2CR_MSEL13_0, - MSEL2CR_MSEL12_0), - PINMUX_DATA(TSIF2_TS_XX2_MARK, MSEL2CR_MSEL14_0, MSEL2CR_MSEL13_0, - MSEL2CR_MSEL12_1), - PINMUX_DATA(TSIF2_TS_XX3_MARK, MSEL2CR_MSEL14_0, MSEL2CR_MSEL13_1, - MSEL2CR_MSEL12_0), - PINMUX_DATA(TSIF2_TS_XX4_MARK, MSEL2CR_MSEL14_0, MSEL2CR_MSEL13_1, - MSEL2CR_MSEL12_1), - PINMUX_DATA(TSIF2_TS_XX5_MARK, MSEL2CR_MSEL14_1, MSEL2CR_MSEL13_0, - MSEL2CR_MSEL12_0), - PINMUX_DATA(TSIF1_TS_XX1_MARK, MSEL2CR_MSEL11_0, MSEL2CR_MSEL10_0, - MSEL2CR_MSEL9_0), - PINMUX_DATA(TSIF1_TS_XX2_MARK, MSEL2CR_MSEL11_0, MSEL2CR_MSEL10_0, - MSEL2CR_MSEL9_1), - PINMUX_DATA(TSIF1_TS_XX3_MARK, MSEL2CR_MSEL11_0, MSEL2CR_MSEL10_1, - MSEL2CR_MSEL9_0), - PINMUX_DATA(TSIF1_TS_XX4_MARK, MSEL2CR_MSEL11_0, MSEL2CR_MSEL10_1, - MSEL2CR_MSEL9_1), - PINMUX_DATA(TSIF1_TS_XX5_MARK, MSEL2CR_MSEL11_1, MSEL2CR_MSEL10_0, - MSEL2CR_MSEL9_0), - PINMUX_DATA(TSIF0_TS_XX1_MARK, MSEL2CR_MSEL8_0, MSEL2CR_MSEL7_0, - MSEL2CR_MSEL6_0), - PINMUX_DATA(TSIF0_TS_XX2_MARK, MSEL2CR_MSEL8_0, MSEL2CR_MSEL7_0, - MSEL2CR_MSEL6_1), - PINMUX_DATA(TSIF0_TS_XX3_MARK, MSEL2CR_MSEL8_0, MSEL2CR_MSEL7_1, - MSEL2CR_MSEL6_0), - PINMUX_DATA(TSIF0_TS_XX4_MARK, MSEL2CR_MSEL8_0, MSEL2CR_MSEL7_1, - MSEL2CR_MSEL6_1), - PINMUX_DATA(TSIF0_TS_XX5_MARK, MSEL2CR_MSEL8_1, MSEL2CR_MSEL7_0, - MSEL2CR_MSEL6_0), - PINMUX_DATA(MST1_TS_XX1_MARK, MSEL2CR_MSEL5_0, MSEL2CR_MSEL4_0, - MSEL2CR_MSEL3_0), - PINMUX_DATA(MST1_TS_XX2_MARK, MSEL2CR_MSEL5_0, MSEL2CR_MSEL4_0, - MSEL2CR_MSEL3_1), - PINMUX_DATA(MST1_TS_XX3_MARK, MSEL2CR_MSEL5_0, MSEL2CR_MSEL4_1, - MSEL2CR_MSEL3_0), - PINMUX_DATA(MST1_TS_XX4_MARK, MSEL2CR_MSEL5_0, MSEL2CR_MSEL4_1, - MSEL2CR_MSEL3_1), - PINMUX_DATA(MST1_TS_XX5_MARK, MSEL2CR_MSEL5_1, MSEL2CR_MSEL4_0, - MSEL2CR_MSEL3_0), - PINMUX_DATA(MST0_TS_XX1_MARK, MSEL2CR_MSEL2_0, MSEL2CR_MSEL1_0, - MSEL2CR_MSEL0_0), - PINMUX_DATA(MST0_TS_XX2_MARK, MSEL2CR_MSEL2_0, MSEL2CR_MSEL1_0, - MSEL2CR_MSEL0_1), - PINMUX_DATA(MST0_TS_XX3_MARK, MSEL2CR_MSEL2_0, MSEL2CR_MSEL1_1, - MSEL2CR_MSEL0_0), - PINMUX_DATA(MST0_TS_XX4_MARK, MSEL2CR_MSEL2_0, MSEL2CR_MSEL1_1, - MSEL2CR_MSEL0_1), - PINMUX_DATA(MST0_TS_XX5_MARK, MSEL2CR_MSEL2_1, MSEL2CR_MSEL1_0, - MSEL2CR_MSEL0_0), - - /* MSEL3 special cases */ - PINMUX_DATA(SDHI0_VCCQ_MC0_ON_MARK, MSEL3CR_MSEL28_1), - PINMUX_DATA(SDHI0_VCCQ_MC0_OFF_MARK, MSEL3CR_MSEL28_0), - PINMUX_DATA(DEBUG_MON_VIO_MARK, MSEL3CR_MSEL15_0), - PINMUX_DATA(DEBUG_MON_LCDD_MARK, MSEL3CR_MSEL15_1), - PINMUX_DATA(LCDC_LCDC0_MARK, MSEL3CR_MSEL6_0), - PINMUX_DATA(LCDC_LCDC1_MARK, MSEL3CR_MSEL6_1), - - /* MSEL4 special cases */ - PINMUX_DATA(IRQ9_MEM_INT_MARK, MSEL4CR_MSEL29_0), - PINMUX_DATA(IRQ9_MCP_INT_MARK, MSEL4CR_MSEL29_1), - PINMUX_DATA(A11_MARK, MSEL4CR_MSEL13_0, MSEL4CR_MSEL12_0), - PINMUX_DATA(KEYOUT8_MARK, MSEL4CR_MSEL13_0, MSEL4CR_MSEL12_1), - PINMUX_DATA(TPU4TO3_MARK, MSEL4CR_MSEL13_1, MSEL4CR_MSEL12_0), - PINMUX_DATA(RESETA_N_PU_ON_MARK, MSEL4CR_MSEL4_0), - PINMUX_DATA(RESETA_N_PU_OFF_MARK, MSEL4CR_MSEL4_1), - PINMUX_DATA(EDBGREQ_PD_MARK, MSEL4CR_MSEL1_0), - PINMUX_DATA(EDBGREQ_PU_MARK, MSEL4CR_MSEL1_1), - - /* Functions with pull-ups */ - PINMUX_DATA(KEYIN0_PU_MARK, PORT66_FN2, PORT66_IN_PU), - PINMUX_DATA(KEYIN1_PU_MARK, PORT67_FN2, PORT67_IN_PU), - PINMUX_DATA(KEYIN2_PU_MARK, PORT68_FN2, PORT68_IN_PU), - PINMUX_DATA(KEYIN3_PU_MARK, PORT69_FN2, PORT69_IN_PU), - PINMUX_DATA(KEYIN4_PU_MARK, PORT70_FN2, PORT70_IN_PU), - PINMUX_DATA(KEYIN5_PU_MARK, PORT71_FN2, PORT71_IN_PU), - PINMUX_DATA(KEYIN6_PU_MARK, PORT72_FN2, PORT72_IN_PU), - PINMUX_DATA(KEYIN7_PU_MARK, PORT73_FN2, PORT73_IN_PU), - - PINMUX_DATA(SDHICD0_PU_MARK, PORT251_FN1, PORT251_IN_PU), - PINMUX_DATA(SDHID0_0_PU_MARK, PORT252_FN1, PORT252_IN_PU), - PINMUX_DATA(SDHID0_1_PU_MARK, PORT253_FN1, PORT253_IN_PU), - PINMUX_DATA(SDHID0_2_PU_MARK, PORT254_FN1, PORT254_IN_PU), - PINMUX_DATA(SDHID0_3_PU_MARK, PORT255_FN1, PORT255_IN_PU), - PINMUX_DATA(SDHICMD0_PU_MARK, PORT256_FN1, PORT256_IN_PU), - PINMUX_DATA(SDHIWP0_PU_MARK, PORT257_FN1, PORT256_IN_PU), - PINMUX_DATA(SDHID1_0_PU_MARK, PORT259_FN1, PORT259_IN_PU), - PINMUX_DATA(SDHID1_1_PU_MARK, PORT260_FN1, PORT260_IN_PU), - PINMUX_DATA(SDHID1_2_PU_MARK, PORT261_FN1, PORT261_IN_PU), - PINMUX_DATA(SDHID1_3_PU_MARK, PORT262_FN1, PORT262_IN_PU), - PINMUX_DATA(SDHICMD1_PU_MARK, PORT263_FN1, PORT263_IN_PU), - PINMUX_DATA(SDHID2_0_PU_MARK, PORT265_FN1, PORT265_IN_PU), - PINMUX_DATA(SDHID2_1_PU_MARK, PORT266_FN1, PORT266_IN_PU), - PINMUX_DATA(SDHID2_2_PU_MARK, PORT267_FN1, PORT267_IN_PU), - PINMUX_DATA(SDHID2_3_PU_MARK, PORT268_FN1, PORT268_IN_PU), - PINMUX_DATA(SDHICMD2_PU_MARK, PORT269_FN1, PORT269_IN_PU), - - PINMUX_DATA(MMCCMD0_PU_MARK, PORT279_FN1, PORT279_IN_PU, - MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCCMD1_PU_MARK, PORT297_FN2, PORT297_IN_PU, - MSEL4CR_MSEL15_1), - - PINMUX_DATA(MMCD0_0_PU_MARK, - PORT271_FN1, PORT271_IN_PU, MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCD0_1_PU_MARK, - PORT272_FN1, PORT272_IN_PU, MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCD0_2_PU_MARK, - PORT273_FN1, PORT273_IN_PU, MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCD0_3_PU_MARK, - PORT274_FN1, PORT274_IN_PU, MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCD0_4_PU_MARK, - PORT275_FN1, PORT275_IN_PU, MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCD0_5_PU_MARK, - PORT276_FN1, PORT276_IN_PU, MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCD0_6_PU_MARK, - PORT277_FN1, PORT277_IN_PU, MSEL4CR_MSEL15_0), - PINMUX_DATA(MMCD0_7_PU_MARK, - PORT278_FN1, PORT278_IN_PU, MSEL4CR_MSEL15_0), - - PINMUX_DATA(FSIBISLD_PU_MARK, PORT39_FN1, PORT39_IN_PU), - PINMUX_DATA(FSIACK_PU_MARK, PORT49_FN1, PORT49_IN_PU), - PINMUX_DATA(FSIAILR_PU_MARK, PORT50_FN5, PORT50_IN_PU), - PINMUX_DATA(FSIAIBT_PU_MARK, PORT51_FN5, PORT51_IN_PU), - PINMUX_DATA(FSIAISLD_PU_MARK, PORT55_FN1, PORT55_IN_PU), -}; - -static struct pinmux_gpio pinmux_gpios[] = { - GPIO_PORT_ALL(), - - /* Table 25-1 (Functions 0-7) */ - GPIO_FN(VBUS_0), - GPIO_FN(GPI0), - GPIO_FN(GPI1), - GPIO_FN(GPI2), - GPIO_FN(GPI3), - GPIO_FN(GPI4), - GPIO_FN(GPI5), - GPIO_FN(GPI6), - GPIO_FN(GPI7), - GPIO_FN(SCIFA7_RXD), - GPIO_FN(SCIFA7_CTS_), - GPIO_FN(GPO7), \ - GPIO_FN(MFG0_OUT2), - GPIO_FN(GPO6), \ - GPIO_FN(MFG1_OUT2), - GPIO_FN(GPO5), \ - GPIO_FN(SCIFA0_SCK), \ - GPIO_FN(FSICOSLDT3), \ - GPIO_FN(PORT16_VIO_CKOR), - GPIO_FN(SCIFA0_TXD), - GPIO_FN(SCIFA7_TXD), - GPIO_FN(SCIFA7_RTS_), \ - GPIO_FN(PORT19_VIO_CKO2), - GPIO_FN(GPO0), - GPIO_FN(GPO1), - GPIO_FN(GPO2), \ - GPIO_FN(STATUS0), - GPIO_FN(GPO3), \ - GPIO_FN(STATUS1), - GPIO_FN(GPO4), \ - GPIO_FN(STATUS2), - GPIO_FN(VINT), - GPIO_FN(TCKON), - GPIO_FN(XDVFS1), \ - GPIO_FN(PORT27_I2C_SCL2), \ - GPIO_FN(PORT27_I2C_SCL3), \ - GPIO_FN(MFG0_OUT1), \ - GPIO_FN(PORT27_IROUT), - GPIO_FN(XDVFS2), \ - GPIO_FN(PORT28_I2C_SDA2), \ - GPIO_FN(PORT28_I2C_SDA3), \ - GPIO_FN(PORT28_TPU1TO1), - GPIO_FN(SIM_RST), \ - GPIO_FN(PORT29_TPU1TO1), - GPIO_FN(SIM_CLK), \ - GPIO_FN(PORT30_VIO_CKOR), - GPIO_FN(SIM_D), \ - GPIO_FN(PORT31_IROUT), - GPIO_FN(SCIFA4_TXD), - GPIO_FN(SCIFA4_RXD), \ - GPIO_FN(XWUP), - GPIO_FN(SCIFA4_RTS_), - GPIO_FN(SCIFA4_CTS_), - GPIO_FN(FSIBOBT), \ - GPIO_FN(FSIBIBT), - GPIO_FN(FSIBOLR), \ - GPIO_FN(FSIBILR), - GPIO_FN(FSIBOSLD), - GPIO_FN(FSIBISLD), - GPIO_FN(VACK), - GPIO_FN(XTAL1L), - GPIO_FN(SCIFA0_RTS_), \ - GPIO_FN(FSICOSLDT2), - GPIO_FN(SCIFA0_RXD), - GPIO_FN(SCIFA0_CTS_), \ - GPIO_FN(FSICOSLDT1), - GPIO_FN(FSICOBT), \ - GPIO_FN(FSICIBT), \ - GPIO_FN(FSIDOBT), \ - GPIO_FN(FSIDIBT), - GPIO_FN(FSICOLR), \ - GPIO_FN(FSICILR), \ - GPIO_FN(FSIDOLR), \ - GPIO_FN(FSIDILR), - GPIO_FN(FSICOSLD), \ - GPIO_FN(PORT47_FSICSPDIF), - GPIO_FN(FSICISLD), \ - GPIO_FN(FSIDISLD), - GPIO_FN(FSIACK), \ - GPIO_FN(PORT49_IRDA_OUT), \ - GPIO_FN(PORT49_IROUT), \ - GPIO_FN(FSIAOMC), - GPIO_FN(FSIAOLR), \ - GPIO_FN(BBIF2_TSYNC2), \ - GPIO_FN(TPU2TO2), \ - GPIO_FN(FSIAILR), - - GPIO_FN(FSIAOBT), \ - GPIO_FN(BBIF2_TSCK2), \ - GPIO_FN(TPU2TO3), \ - GPIO_FN(FSIAIBT), - GPIO_FN(FSIAOSLD), \ - GPIO_FN(BBIF2_TXD2), - GPIO_FN(FSIASPDIF), \ - GPIO_FN(PORT53_IRDA_IN), \ - GPIO_FN(TPU3TO3), \ - GPIO_FN(FSIBSPDIF), \ - GPIO_FN(PORT53_FSICSPDIF), - GPIO_FN(FSIBCK), \ - GPIO_FN(PORT54_IRDA_FIRSEL), \ - GPIO_FN(TPU3TO2), \ - GPIO_FN(FSIBOMC), \ - GPIO_FN(FSICCK), \ - GPIO_FN(FSICOMC), - GPIO_FN(FSIAISLD), \ - GPIO_FN(TPU0TO0), - GPIO_FN(A0), \ - GPIO_FN(BS_), - GPIO_FN(A12), \ - GPIO_FN(PORT58_KEYOUT7), \ - GPIO_FN(TPU4TO2), - GPIO_FN(A13), \ - GPIO_FN(PORT59_KEYOUT6), \ - GPIO_FN(TPU0TO1), - GPIO_FN(A14), \ - GPIO_FN(KEYOUT5), - GPIO_FN(A15), \ - GPIO_FN(KEYOUT4), - GPIO_FN(A16), \ - GPIO_FN(KEYOUT3), \ - GPIO_FN(MSIOF0_SS1), - GPIO_FN(A17), \ - GPIO_FN(KEYOUT2), \ - GPIO_FN(MSIOF0_TSYNC), - GPIO_FN(A18), \ - GPIO_FN(KEYOUT1), \ - GPIO_FN(MSIOF0_TSCK), - GPIO_FN(A19), \ - GPIO_FN(KEYOUT0), \ - GPIO_FN(MSIOF0_TXD), - GPIO_FN(A20), \ - GPIO_FN(KEYIN0), \ - GPIO_FN(MSIOF0_RSCK), - GPIO_FN(A21), \ - GPIO_FN(KEYIN1), \ - GPIO_FN(MSIOF0_RSYNC), - GPIO_FN(A22), \ - GPIO_FN(KEYIN2), \ - GPIO_FN(MSIOF0_MCK0), - GPIO_FN(A23), \ - GPIO_FN(KEYIN3), \ - GPIO_FN(MSIOF0_MCK1), - GPIO_FN(A24), \ - GPIO_FN(KEYIN4), \ - GPIO_FN(MSIOF0_RXD), - GPIO_FN(A25), \ - GPIO_FN(KEYIN5), \ - GPIO_FN(MSIOF0_SS2), - GPIO_FN(A26), \ - GPIO_FN(KEYIN6), - GPIO_FN(KEYIN7), - GPIO_FN(D0_NAF0), - GPIO_FN(D1_NAF1), - GPIO_FN(D2_NAF2), - GPIO_FN(D3_NAF3), - GPIO_FN(D4_NAF4), - GPIO_FN(D5_NAF5), - GPIO_FN(D6_NAF6), - GPIO_FN(D7_NAF7), - GPIO_FN(D8_NAF8), - GPIO_FN(D9_NAF9), - GPIO_FN(D10_NAF10), - GPIO_FN(D11_NAF11), - GPIO_FN(D12_NAF12), - GPIO_FN(D13_NAF13), - GPIO_FN(D14_NAF14), - GPIO_FN(D15_NAF15), - GPIO_FN(CS4_), - GPIO_FN(CS5A_), \ - GPIO_FN(PORT91_RDWR), - GPIO_FN(CS5B_), \ - GPIO_FN(FCE1_), - GPIO_FN(CS6B_), \ - GPIO_FN(DACK0), - GPIO_FN(FCE0_), \ - GPIO_FN(CS6A_), - GPIO_FN(WAIT_), \ - GPIO_FN(DREQ0), - GPIO_FN(RD__FSC), - GPIO_FN(WE0__FWE), \ - GPIO_FN(RDWR_FWE), - GPIO_FN(WE1_), - GPIO_FN(FRB), - GPIO_FN(CKO), - GPIO_FN(NBRSTOUT_), - GPIO_FN(NBRST_), - GPIO_FN(BBIF2_TXD), - GPIO_FN(BBIF2_RXD), - GPIO_FN(BBIF2_SYNC), - GPIO_FN(BBIF2_SCK), - GPIO_FN(SCIFA3_CTS_), \ - GPIO_FN(MFG3_IN2), - GPIO_FN(SCIFA3_RXD), \ - GPIO_FN(MFG3_IN1), - GPIO_FN(BBIF1_SS2), \ - GPIO_FN(SCIFA3_RTS_), \ - GPIO_FN(MFG3_OUT1), - GPIO_FN(SCIFA3_TXD), - GPIO_FN(HSI_RX_DATA), \ - GPIO_FN(BBIF1_RXD), - GPIO_FN(HSI_TX_WAKE), \ - GPIO_FN(BBIF1_TSCK), - GPIO_FN(HSI_TX_DATA), \ - GPIO_FN(BBIF1_TSYNC), - GPIO_FN(HSI_TX_READY), \ - GPIO_FN(BBIF1_TXD), - GPIO_FN(HSI_RX_READY), \ - GPIO_FN(BBIF1_RSCK), \ - GPIO_FN(PORT115_I2C_SCL2), \ - GPIO_FN(PORT115_I2C_SCL3), - GPIO_FN(HSI_RX_WAKE), \ - GPIO_FN(BBIF1_RSYNC), \ - GPIO_FN(PORT116_I2C_SDA2), \ - GPIO_FN(PORT116_I2C_SDA3), - GPIO_FN(HSI_RX_FLAG), \ - GPIO_FN(BBIF1_SS1), \ - GPIO_FN(BBIF1_FLOW), - GPIO_FN(HSI_TX_FLAG), - GPIO_FN(VIO_VD), \ - GPIO_FN(PORT128_LCD2VSYN), \ - GPIO_FN(VIO2_VD), \ - GPIO_FN(LCD2D0), - - GPIO_FN(VIO_HD), \ - GPIO_FN(PORT129_LCD2HSYN), \ - GPIO_FN(PORT129_LCD2CS_), \ - GPIO_FN(VIO2_HD), \ - GPIO_FN(LCD2D1), - GPIO_FN(VIO_D0), \ - GPIO_FN(PORT130_MSIOF2_RXD), \ - GPIO_FN(LCD2D10), - GPIO_FN(VIO_D1), \ - GPIO_FN(PORT131_KEYOUT6), \ - GPIO_FN(PORT131_MSIOF2_SS1), \ - GPIO_FN(PORT131_KEYOUT11), \ - GPIO_FN(LCD2D11), - GPIO_FN(VIO_D2), \ - GPIO_FN(PORT132_KEYOUT7), \ - GPIO_FN(PORT132_MSIOF2_SS2), \ - GPIO_FN(PORT132_KEYOUT10), \ - GPIO_FN(LCD2D12), - GPIO_FN(VIO_D3), \ - GPIO_FN(MSIOF2_TSYNC), \ - GPIO_FN(LCD2D13), - GPIO_FN(VIO_D4), \ - GPIO_FN(MSIOF2_TXD), \ - GPIO_FN(LCD2D14), - GPIO_FN(VIO_D5), \ - GPIO_FN(MSIOF2_TSCK), \ - GPIO_FN(LCD2D15), - GPIO_FN(VIO_D6), \ - GPIO_FN(PORT136_KEYOUT8), \ - GPIO_FN(LCD2D16), - GPIO_FN(VIO_D7), \ - GPIO_FN(PORT137_KEYOUT9), \ - GPIO_FN(LCD2D17), - GPIO_FN(VIO_D8), \ - GPIO_FN(PORT138_KEYOUT8), \ - GPIO_FN(VIO2_D0), \ - GPIO_FN(LCD2D6), - GPIO_FN(VIO_D9), \ - GPIO_FN(PORT139_KEYOUT9), \ - GPIO_FN(VIO2_D1), \ - GPIO_FN(LCD2D7), - GPIO_FN(VIO_D10), \ - GPIO_FN(TPU0TO2), \ - GPIO_FN(VIO2_D2), \ - GPIO_FN(LCD2D8), - GPIO_FN(VIO_D11), \ - GPIO_FN(TPU0TO3), \ - GPIO_FN(VIO2_D3), \ - GPIO_FN(LCD2D9), - GPIO_FN(VIO_D12), \ - GPIO_FN(PORT142_KEYOUT10), \ - GPIO_FN(VIO2_D4), \ - GPIO_FN(LCD2D2), - GPIO_FN(VIO_D13), \ - GPIO_FN(PORT143_KEYOUT11), \ - GPIO_FN(PORT143_KEYOUT6), \ - GPIO_FN(VIO2_D5), \ - GPIO_FN(LCD2D3), - GPIO_FN(VIO_D14), \ - GPIO_FN(PORT144_KEYOUT7), \ - GPIO_FN(VIO2_D6), \ - GPIO_FN(LCD2D4), - GPIO_FN(VIO_D15), \ - GPIO_FN(TPU1TO3), \ - GPIO_FN(PORT145_LCD2DISP), \ - GPIO_FN(PORT145_LCD2RS), \ - GPIO_FN(VIO2_D7), \ - GPIO_FN(LCD2D5), - GPIO_FN(VIO_CLK), \ - GPIO_FN(LCD2DCK), \ - GPIO_FN(PORT146_LCD2WR_), \ - GPIO_FN(VIO2_CLK), \ - GPIO_FN(LCD2D18), - GPIO_FN(VIO_FIELD), \ - GPIO_FN(LCD2RD_), \ - GPIO_FN(VIO2_FIELD), \ - GPIO_FN(LCD2D19), - GPIO_FN(VIO_CKO), - GPIO_FN(A27), \ - GPIO_FN(PORT149_RDWR), \ - GPIO_FN(MFG0_IN1), \ - GPIO_FN(PORT149_KEYOUT9), - GPIO_FN(MFG0_IN2), - GPIO_FN(TS_SPSYNC3), \ - GPIO_FN(MSIOF2_RSCK), - GPIO_FN(TS_SDAT3), \ - GPIO_FN(MSIOF2_RSYNC), - GPIO_FN(TPU1TO2), \ - GPIO_FN(TS_SDEN3), \ - GPIO_FN(PORT153_MSIOF2_SS1), - GPIO_FN(SCIFA2_TXD1), \ - GPIO_FN(MSIOF2_MCK0), - GPIO_FN(SCIFA2_RXD1), \ - GPIO_FN(MSIOF2_MCK1), - GPIO_FN(SCIFA2_RTS1_), \ - GPIO_FN(PORT156_MSIOF2_SS2), - GPIO_FN(SCIFA2_CTS1_), \ - GPIO_FN(PORT157_MSIOF2_RXD), - GPIO_FN(DINT_), \ - GPIO_FN(SCIFA2_SCK1), \ - GPIO_FN(TS_SCK3), - GPIO_FN(PORT159_SCIFB_SCK), \ - GPIO_FN(PORT159_SCIFA5_SCK), \ - GPIO_FN(NMI), - GPIO_FN(PORT160_SCIFB_TXD), \ - GPIO_FN(PORT160_SCIFA5_TXD), - GPIO_FN(PORT161_SCIFB_CTS_), \ - GPIO_FN(PORT161_SCIFA5_CTS_), - GPIO_FN(PORT162_SCIFB_RXD), \ - GPIO_FN(PORT162_SCIFA5_RXD), - GPIO_FN(PORT163_SCIFB_RTS_), \ - GPIO_FN(PORT163_SCIFA5_RTS_), \ - GPIO_FN(TPU3TO0), - GPIO_FN(LCDD0), - GPIO_FN(LCDD1), \ - GPIO_FN(PORT193_SCIFA5_CTS_), \ - GPIO_FN(BBIF2_TSYNC1), - GPIO_FN(LCDD2), \ - GPIO_FN(PORT194_SCIFA5_RTS_), \ - GPIO_FN(BBIF2_TSCK1), - GPIO_FN(LCDD3), \ - GPIO_FN(PORT195_SCIFA5_RXD), \ - GPIO_FN(BBIF2_TXD1), - GPIO_FN(LCDD4), \ - GPIO_FN(PORT196_SCIFA5_TXD), - GPIO_FN(LCDD5), \ - GPIO_FN(PORT197_SCIFA5_SCK), \ - GPIO_FN(MFG2_OUT2), \ - GPIO_FN(TPU2TO1), - GPIO_FN(LCDD6), - GPIO_FN(LCDD7), \ - GPIO_FN(TPU4TO1), \ - GPIO_FN(MFG4_OUT2), - GPIO_FN(LCDD8), \ - GPIO_FN(D16), - GPIO_FN(LCDD9), \ - GPIO_FN(D17), - GPIO_FN(LCDD10), \ - GPIO_FN(D18), - GPIO_FN(LCDD11), \ - GPIO_FN(D19), - GPIO_FN(LCDD12), \ - GPIO_FN(D20), - GPIO_FN(LCDD13), \ - GPIO_FN(D21), - GPIO_FN(LCDD14), \ - GPIO_FN(D22), - GPIO_FN(LCDD15), \ - GPIO_FN(PORT207_MSIOF0L_SS1), \ - GPIO_FN(D23), - GPIO_FN(LCDD16), \ - GPIO_FN(PORT208_MSIOF0L_SS2), \ - GPIO_FN(D24), - GPIO_FN(LCDD17), \ - GPIO_FN(D25), - GPIO_FN(LCDD18), \ - GPIO_FN(DREQ2), \ - GPIO_FN(PORT210_MSIOF0L_SS1), \ - GPIO_FN(D26), - GPIO_FN(LCDD19), \ - GPIO_FN(PORT211_MSIOF0L_SS2), \ - GPIO_FN(D27), - GPIO_FN(LCDD20), \ - GPIO_FN(TS_SPSYNC1), \ - GPIO_FN(MSIOF0L_MCK0), \ - GPIO_FN(D28), - GPIO_FN(LCDD21), \ - GPIO_FN(TS_SDAT1), \ - GPIO_FN(MSIOF0L_MCK1), \ - GPIO_FN(D29), - GPIO_FN(LCDD22), \ - GPIO_FN(TS_SDEN1), \ - GPIO_FN(MSIOF0L_RSCK), \ - GPIO_FN(D30), - GPIO_FN(LCDD23), \ - GPIO_FN(TS_SCK1), \ - GPIO_FN(MSIOF0L_RSYNC), \ - GPIO_FN(D31), - GPIO_FN(LCDDCK), \ - GPIO_FN(LCDWR_), - GPIO_FN(LCDRD_), \ - GPIO_FN(DACK2), \ - GPIO_FN(PORT217_LCD2RS), \ - GPIO_FN(MSIOF0L_TSYNC), \ - GPIO_FN(VIO2_FIELD3), \ - GPIO_FN(PORT217_LCD2DISP), - GPIO_FN(LCDHSYN), \ - GPIO_FN(LCDCS_), \ - GPIO_FN(LCDCS2_), \ - GPIO_FN(DACK3), \ - GPIO_FN(PORT218_VIO_CKOR), - GPIO_FN(LCDDISP), \ - GPIO_FN(LCDRS), \ - GPIO_FN(PORT219_LCD2WR_), \ - GPIO_FN(DREQ3), \ - GPIO_FN(MSIOF0L_TSCK), \ - GPIO_FN(VIO2_CLK3), \ - GPIO_FN(LCD2DCK_2), - GPIO_FN(LCDVSYN), \ - GPIO_FN(LCDVSYN2), - GPIO_FN(LCDLCLK), \ - GPIO_FN(DREQ1), \ - GPIO_FN(PORT221_LCD2CS_), \ - GPIO_FN(PWEN), \ - GPIO_FN(MSIOF0L_RXD), \ - GPIO_FN(VIO2_HD3), \ - GPIO_FN(PORT221_LCD2HSYN), - GPIO_FN(LCDDON), \ - GPIO_FN(LCDDON2), \ - GPIO_FN(DACK1), \ - GPIO_FN(OVCN), \ - GPIO_FN(MSIOF0L_TXD), \ - GPIO_FN(VIO2_VD3), \ - GPIO_FN(PORT222_LCD2VSYN), - - GPIO_FN(SCIFA1_TXD), \ - GPIO_FN(OVCN2), - GPIO_FN(EXTLP), \ - GPIO_FN(SCIFA1_SCK), \ - GPIO_FN(PORT226_VIO_CKO2), - GPIO_FN(SCIFA1_RTS_), \ - GPIO_FN(IDIN), - GPIO_FN(SCIFA1_RXD), - GPIO_FN(SCIFA1_CTS_), \ - GPIO_FN(MFG1_IN1), - GPIO_FN(MSIOF1_TXD), \ - GPIO_FN(SCIFA2_TXD2), - GPIO_FN(MSIOF1_TSYNC), \ - GPIO_FN(SCIFA2_CTS2_), - GPIO_FN(MSIOF1_TSCK), \ - GPIO_FN(SCIFA2_SCK2), - GPIO_FN(MSIOF1_RXD), \ - GPIO_FN(SCIFA2_RXD2), - GPIO_FN(MSIOF1_RSCK), \ - GPIO_FN(SCIFA2_RTS2_), \ - GPIO_FN(VIO2_CLK2), \ - GPIO_FN(LCD2D20), - GPIO_FN(MSIOF1_RSYNC), \ - GPIO_FN(MFG1_IN2), \ - GPIO_FN(VIO2_VD2), \ - GPIO_FN(LCD2D21), - GPIO_FN(MSIOF1_MCK0), \ - GPIO_FN(PORT236_I2C_SDA2), - GPIO_FN(MSIOF1_MCK1), \ - GPIO_FN(PORT237_I2C_SCL2), - GPIO_FN(MSIOF1_SS1), \ - GPIO_FN(VIO2_FIELD2), \ - GPIO_FN(LCD2D22), - GPIO_FN(MSIOF1_SS2), \ - GPIO_FN(VIO2_HD2), \ - GPIO_FN(LCD2D23), - GPIO_FN(SCIFA6_TXD), - GPIO_FN(PORT241_IRDA_OUT), \ - GPIO_FN(PORT241_IROUT), \ - GPIO_FN(MFG4_OUT1), \ - GPIO_FN(TPU4TO0), - GPIO_FN(PORT242_IRDA_IN), \ - GPIO_FN(MFG4_IN2), - GPIO_FN(PORT243_IRDA_FIRSEL), \ - GPIO_FN(PORT243_VIO_CKO2), - GPIO_FN(PORT244_SCIFA5_CTS_), \ - GPIO_FN(MFG2_IN1), \ - GPIO_FN(PORT244_SCIFB_CTS_), \ - GPIO_FN(MSIOF2R_RXD), - GPIO_FN(PORT245_SCIFA5_RTS_), \ - GPIO_FN(MFG2_IN2), \ - GPIO_FN(PORT245_SCIFB_RTS_), \ - GPIO_FN(MSIOF2R_TXD), - GPIO_FN(PORT246_SCIFA5_RXD), \ - GPIO_FN(MFG1_OUT1), \ - GPIO_FN(PORT246_SCIFB_RXD), \ - GPIO_FN(TPU1TO0), - GPIO_FN(PORT247_SCIFA5_TXD), \ - GPIO_FN(MFG3_OUT2), \ - GPIO_FN(PORT247_SCIFB_TXD), \ - GPIO_FN(TPU3TO1), - GPIO_FN(PORT248_SCIFA5_SCK), \ - GPIO_FN(MFG2_OUT1), \ - GPIO_FN(PORT248_SCIFB_SCK), \ - GPIO_FN(TPU2TO0), \ - GPIO_FN(PORT248_I2C_SCL3), \ - GPIO_FN(MSIOF2R_TSCK), - GPIO_FN(PORT249_IROUT), \ - GPIO_FN(MFG4_IN1), \ - GPIO_FN(PORT249_I2C_SDA3), \ - GPIO_FN(MSIOF2R_TSYNC), - GPIO_FN(SDHICLK0), - GPIO_FN(SDHICD0), - GPIO_FN(SDHID0_0), - GPIO_FN(SDHID0_1), - GPIO_FN(SDHID0_2), - GPIO_FN(SDHID0_3), - GPIO_FN(SDHICMD0), - GPIO_FN(SDHIWP0), - GPIO_FN(SDHICLK1), - GPIO_FN(SDHID1_0), \ - GPIO_FN(TS_SPSYNC2), - GPIO_FN(SDHID1_1), \ - GPIO_FN(TS_SDAT2), - GPIO_FN(SDHID1_2), \ - GPIO_FN(TS_SDEN2), - GPIO_FN(SDHID1_3), \ - GPIO_FN(TS_SCK2), - GPIO_FN(SDHICMD1), - GPIO_FN(SDHICLK2), - GPIO_FN(SDHID2_0), \ - GPIO_FN(TS_SPSYNC4), - GPIO_FN(SDHID2_1), \ - GPIO_FN(TS_SDAT4), - GPIO_FN(SDHID2_2), \ - GPIO_FN(TS_SDEN4), - GPIO_FN(SDHID2_3), \ - GPIO_FN(TS_SCK4), - GPIO_FN(SDHICMD2), - GPIO_FN(MMCCLK0), - GPIO_FN(MMCD0_0), - GPIO_FN(MMCD0_1), - GPIO_FN(MMCD0_2), - GPIO_FN(MMCD0_3), - GPIO_FN(MMCD0_4), \ - GPIO_FN(TS_SPSYNC5), - GPIO_FN(MMCD0_5), \ - GPIO_FN(TS_SDAT5), - GPIO_FN(MMCD0_6), \ - GPIO_FN(TS_SDEN5), - GPIO_FN(MMCD0_7), \ - GPIO_FN(TS_SCK5), - GPIO_FN(MMCCMD0), - GPIO_FN(RESETOUTS_), \ - GPIO_FN(EXTAL2OUT), - GPIO_FN(MCP_WAIT__MCP_FRB), - GPIO_FN(MCP_CKO), \ - GPIO_FN(MMCCLK1), - GPIO_FN(MCP_D15_MCP_NAF15), - GPIO_FN(MCP_D14_MCP_NAF14), - GPIO_FN(MCP_D13_MCP_NAF13), - GPIO_FN(MCP_D12_MCP_NAF12), - GPIO_FN(MCP_D11_MCP_NAF11), - GPIO_FN(MCP_D10_MCP_NAF10), - GPIO_FN(MCP_D9_MCP_NAF9), - GPIO_FN(MCP_D8_MCP_NAF8), \ - GPIO_FN(MMCCMD1), - GPIO_FN(MCP_D7_MCP_NAF7), \ - GPIO_FN(MMCD1_7), - - GPIO_FN(MCP_D6_MCP_NAF6), \ - GPIO_FN(MMCD1_6), - GPIO_FN(MCP_D5_MCP_NAF5), \ - GPIO_FN(MMCD1_5), - GPIO_FN(MCP_D4_MCP_NAF4), \ - GPIO_FN(MMCD1_4), - GPIO_FN(MCP_D3_MCP_NAF3), \ - GPIO_FN(MMCD1_3), - GPIO_FN(MCP_D2_MCP_NAF2), \ - GPIO_FN(MMCD1_2), - GPIO_FN(MCP_D1_MCP_NAF1), \ - GPIO_FN(MMCD1_1), - GPIO_FN(MCP_D0_MCP_NAF0), \ - GPIO_FN(MMCD1_0), - GPIO_FN(MCP_NBRSTOUT_), - GPIO_FN(MCP_WE0__MCP_FWE), \ - GPIO_FN(MCP_RDWR_MCP_FWE), - - /* MSEL2 special cases */ - GPIO_FN(TSIF2_TS_XX1), - GPIO_FN(TSIF2_TS_XX2), - GPIO_FN(TSIF2_TS_XX3), - GPIO_FN(TSIF2_TS_XX4), - GPIO_FN(TSIF2_TS_XX5), - GPIO_FN(TSIF1_TS_XX1), - GPIO_FN(TSIF1_TS_XX2), - GPIO_FN(TSIF1_TS_XX3), - GPIO_FN(TSIF1_TS_XX4), - GPIO_FN(TSIF1_TS_XX5), - GPIO_FN(TSIF0_TS_XX1), - GPIO_FN(TSIF0_TS_XX2), - GPIO_FN(TSIF0_TS_XX3), - GPIO_FN(TSIF0_TS_XX4), - GPIO_FN(TSIF0_TS_XX5), - GPIO_FN(MST1_TS_XX1), - GPIO_FN(MST1_TS_XX2), - GPIO_FN(MST1_TS_XX3), - GPIO_FN(MST1_TS_XX4), - GPIO_FN(MST1_TS_XX5), - GPIO_FN(MST0_TS_XX1), - GPIO_FN(MST0_TS_XX2), - GPIO_FN(MST0_TS_XX3), - GPIO_FN(MST0_TS_XX4), - GPIO_FN(MST0_TS_XX5), - - /* MSEL3 special cases */ - GPIO_FN(SDHI0_VCCQ_MC0_ON), - GPIO_FN(SDHI0_VCCQ_MC0_OFF), - GPIO_FN(DEBUG_MON_VIO), - GPIO_FN(DEBUG_MON_LCDD), - GPIO_FN(LCDC_LCDC0), - GPIO_FN(LCDC_LCDC1), - - /* MSEL4 special cases */ - GPIO_FN(IRQ9_MEM_INT), - GPIO_FN(IRQ9_MCP_INT), - GPIO_FN(A11), - GPIO_FN(KEYOUT8), - GPIO_FN(TPU4TO3), - GPIO_FN(RESETA_N_PU_ON), - GPIO_FN(RESETA_N_PU_OFF), - GPIO_FN(EDBGREQ_PD), - GPIO_FN(EDBGREQ_PU), - - /* Functions with pull-ups */ - GPIO_FN(KEYIN0_PU), - GPIO_FN(KEYIN1_PU), - GPIO_FN(KEYIN2_PU), - GPIO_FN(KEYIN3_PU), - GPIO_FN(KEYIN4_PU), - GPIO_FN(KEYIN5_PU), - GPIO_FN(KEYIN6_PU), - GPIO_FN(KEYIN7_PU), - GPIO_FN(SDHICD0_PU), - GPIO_FN(SDHID0_0_PU), - GPIO_FN(SDHID0_1_PU), - GPIO_FN(SDHID0_2_PU), - GPIO_FN(SDHID0_3_PU), - GPIO_FN(SDHICMD0_PU), - GPIO_FN(SDHIWP0_PU), - GPIO_FN(SDHID1_0_PU), - GPIO_FN(SDHID1_1_PU), - GPIO_FN(SDHID1_2_PU), - GPIO_FN(SDHID1_3_PU), - GPIO_FN(SDHICMD1_PU), - GPIO_FN(SDHID2_0_PU), - GPIO_FN(SDHID2_1_PU), - GPIO_FN(SDHID2_2_PU), - GPIO_FN(SDHID2_3_PU), - GPIO_FN(SDHICMD2_PU), - GPIO_FN(MMCCMD0_PU), - GPIO_FN(MMCCMD1_PU), - GPIO_FN(MMCD0_0_PU), - GPIO_FN(MMCD0_1_PU), - GPIO_FN(MMCD0_2_PU), - GPIO_FN(MMCD0_3_PU), - GPIO_FN(MMCD0_4_PU), - GPIO_FN(MMCD0_5_PU), - GPIO_FN(MMCD0_6_PU), - GPIO_FN(MMCD0_7_PU), - GPIO_FN(FSIACK_PU), - GPIO_FN(FSIAILR_PU), - GPIO_FN(FSIAIBT_PU), - GPIO_FN(FSIAISLD_PU), -}; - -static struct pinmux_cfg_reg pinmux_config_regs[] = { - PORTCR(0, 0xe6050000), /* PORT0CR */ - PORTCR(1, 0xe6050001), /* PORT1CR */ - PORTCR(2, 0xe6050002), /* PORT2CR */ - PORTCR(3, 0xe6050003), /* PORT3CR */ - PORTCR(4, 0xe6050004), /* PORT4CR */ - PORTCR(5, 0xe6050005), /* PORT5CR */ - PORTCR(6, 0xe6050006), /* PORT6CR */ - PORTCR(7, 0xe6050007), /* PORT7CR */ - PORTCR(8, 0xe6050008), /* PORT8CR */ - PORTCR(9, 0xe6050009), /* PORT9CR */ - - PORTCR(10, 0xe605000a), /* PORT10CR */ - PORTCR(11, 0xe605000b), /* PORT11CR */ - PORTCR(12, 0xe605000c), /* PORT12CR */ - PORTCR(13, 0xe605000d), /* PORT13CR */ - PORTCR(14, 0xe605000e), /* PORT14CR */ - PORTCR(15, 0xe605000f), /* PORT15CR */ - PORTCR(16, 0xe6050010), /* PORT16CR */ - PORTCR(17, 0xe6050011), /* PORT17CR */ - PORTCR(18, 0xe6050012), /* PORT18CR */ - PORTCR(19, 0xe6050013), /* PORT19CR */ - - PORTCR(20, 0xe6050014), /* PORT20CR */ - PORTCR(21, 0xe6050015), /* PORT21CR */ - PORTCR(22, 0xe6050016), /* PORT22CR */ - PORTCR(23, 0xe6050017), /* PORT23CR */ - PORTCR(24, 0xe6050018), /* PORT24CR */ - PORTCR(25, 0xe6050019), /* PORT25CR */ - PORTCR(26, 0xe605001a), /* PORT26CR */ - PORTCR(27, 0xe605001b), /* PORT27CR */ - PORTCR(28, 0xe605001c), /* PORT28CR */ - PORTCR(29, 0xe605001d), /* PORT29CR */ - - PORTCR(30, 0xe605001e), /* PORT30CR */ - PORTCR(31, 0xe605001f), /* PORT31CR */ - PORTCR(32, 0xe6051020), /* PORT32CR */ - PORTCR(33, 0xe6051021), /* PORT33CR */ - PORTCR(34, 0xe6051022), /* PORT34CR */ - PORTCR(35, 0xe6051023), /* PORT35CR */ - PORTCR(36, 0xe6051024), /* PORT36CR */ - PORTCR(37, 0xe6051025), /* PORT37CR */ - PORTCR(38, 0xe6051026), /* PORT38CR */ - PORTCR(39, 0xe6051027), /* PORT39CR */ - - PORTCR(40, 0xe6051028), /* PORT40CR */ - PORTCR(41, 0xe6051029), /* PORT41CR */ - PORTCR(42, 0xe605102a), /* PORT42CR */ - PORTCR(43, 0xe605102b), /* PORT43CR */ - PORTCR(44, 0xe605102c), /* PORT44CR */ - PORTCR(45, 0xe605102d), /* PORT45CR */ - PORTCR(46, 0xe605102e), /* PORT46CR */ - PORTCR(47, 0xe605102f), /* PORT47CR */ - PORTCR(48, 0xe6051030), /* PORT48CR */ - PORTCR(49, 0xe6051031), /* PORT49CR */ - - PORTCR(50, 0xe6051032), /* PORT50CR */ - PORTCR(51, 0xe6051033), /* PORT51CR */ - PORTCR(52, 0xe6051034), /* PORT52CR */ - PORTCR(53, 0xe6051035), /* PORT53CR */ - PORTCR(54, 0xe6051036), /* PORT54CR */ - PORTCR(55, 0xe6051037), /* PORT55CR */ - PORTCR(56, 0xe6051038), /* PORT56CR */ - PORTCR(57, 0xe6051039), /* PORT57CR */ - PORTCR(58, 0xe605103a), /* PORT58CR */ - PORTCR(59, 0xe605103b), /* PORT59CR */ - - PORTCR(60, 0xe605103c), /* PORT60CR */ - PORTCR(61, 0xe605103d), /* PORT61CR */ - PORTCR(62, 0xe605103e), /* PORT62CR */ - PORTCR(63, 0xe605103f), /* PORT63CR */ - PORTCR(64, 0xe6051040), /* PORT64CR */ - PORTCR(65, 0xe6051041), /* PORT65CR */ - PORTCR(66, 0xe6051042), /* PORT66CR */ - PORTCR(67, 0xe6051043), /* PORT67CR */ - PORTCR(68, 0xe6051044), /* PORT68CR */ - PORTCR(69, 0xe6051045), /* PORT69CR */ - - PORTCR(70, 0xe6051046), /* PORT70CR */ - PORTCR(71, 0xe6051047), /* PORT71CR */ - PORTCR(72, 0xe6051048), /* PORT72CR */ - PORTCR(73, 0xe6051049), /* PORT73CR */ - PORTCR(74, 0xe605104a), /* PORT74CR */ - PORTCR(75, 0xe605104b), /* PORT75CR */ - PORTCR(76, 0xe605104c), /* PORT76CR */ - PORTCR(77, 0xe605104d), /* PORT77CR */ - PORTCR(78, 0xe605104e), /* PORT78CR */ - PORTCR(79, 0xe605104f), /* PORT79CR */ - - PORTCR(80, 0xe6051050), /* PORT80CR */ - PORTCR(81, 0xe6051051), /* PORT81CR */ - PORTCR(82, 0xe6051052), /* PORT82CR */ - PORTCR(83, 0xe6051053), /* PORT83CR */ - PORTCR(84, 0xe6051054), /* PORT84CR */ - PORTCR(85, 0xe6051055), /* PORT85CR */ - PORTCR(86, 0xe6051056), /* PORT86CR */ - PORTCR(87, 0xe6051057), /* PORT87CR */ - PORTCR(88, 0xe6051058), /* PORT88CR */ - PORTCR(89, 0xe6051059), /* PORT89CR */ - - PORTCR(90, 0xe605105a), /* PORT90CR */ - PORTCR(91, 0xe605105b), /* PORT91CR */ - PORTCR(92, 0xe605105c), /* PORT92CR */ - PORTCR(93, 0xe605105d), /* PORT93CR */ - PORTCR(94, 0xe605105e), /* PORT94CR */ - PORTCR(95, 0xe605105f), /* PORT95CR */ - PORTCR(96, 0xe6052060), /* PORT96CR */ - PORTCR(97, 0xe6052061), /* PORT97CR */ - PORTCR(98, 0xe6052062), /* PORT98CR */ - PORTCR(99, 0xe6052063), /* PORT99CR */ - - PORTCR(100, 0xe6052064), /* PORT100CR */ - PORTCR(101, 0xe6052065), /* PORT101CR */ - PORTCR(102, 0xe6052066), /* PORT102CR */ - PORTCR(103, 0xe6052067), /* PORT103CR */ - PORTCR(104, 0xe6052068), /* PORT104CR */ - PORTCR(105, 0xe6052069), /* PORT105CR */ - PORTCR(106, 0xe605206a), /* PORT106CR */ - PORTCR(107, 0xe605206b), /* PORT107CR */ - PORTCR(108, 0xe605206c), /* PORT108CR */ - PORTCR(109, 0xe605206d), /* PORT109CR */ - - PORTCR(110, 0xe605206e), /* PORT110CR */ - PORTCR(111, 0xe605206f), /* PORT111CR */ - PORTCR(112, 0xe6052070), /* PORT112CR */ - PORTCR(113, 0xe6052071), /* PORT113CR */ - PORTCR(114, 0xe6052072), /* PORT114CR */ - PORTCR(115, 0xe6052073), /* PORT115CR */ - PORTCR(116, 0xe6052074), /* PORT116CR */ - PORTCR(117, 0xe6052075), /* PORT117CR */ - PORTCR(118, 0xe6052076), /* PORT118CR */ - - PORTCR(128, 0xe6052080), /* PORT128CR */ - PORTCR(129, 0xe6052081), /* PORT129CR */ - - PORTCR(130, 0xe6052082), /* PORT130CR */ - PORTCR(131, 0xe6052083), /* PORT131CR */ - PORTCR(132, 0xe6052084), /* PORT132CR */ - PORTCR(133, 0xe6052085), /* PORT133CR */ - PORTCR(134, 0xe6052086), /* PORT134CR */ - PORTCR(135, 0xe6052087), /* PORT135CR */ - PORTCR(136, 0xe6052088), /* PORT136CR */ - PORTCR(137, 0xe6052089), /* PORT137CR */ - PORTCR(138, 0xe605208a), /* PORT138CR */ - PORTCR(139, 0xe605208b), /* PORT139CR */ - - PORTCR(140, 0xe605208c), /* PORT140CR */ - PORTCR(141, 0xe605208d), /* PORT141CR */ - PORTCR(142, 0xe605208e), /* PORT142CR */ - PORTCR(143, 0xe605208f), /* PORT143CR */ - PORTCR(144, 0xe6052090), /* PORT144CR */ - PORTCR(145, 0xe6052091), /* PORT145CR */ - PORTCR(146, 0xe6052092), /* PORT146CR */ - PORTCR(147, 0xe6052093), /* PORT147CR */ - PORTCR(148, 0xe6052094), /* PORT148CR */ - PORTCR(149, 0xe6052095), /* PORT149CR */ - - PORTCR(150, 0xe6052096), /* PORT150CR */ - PORTCR(151, 0xe6052097), /* PORT151CR */ - PORTCR(152, 0xe6052098), /* PORT152CR */ - PORTCR(153, 0xe6052099), /* PORT153CR */ - PORTCR(154, 0xe605209a), /* PORT154CR */ - PORTCR(155, 0xe605209b), /* PORT155CR */ - PORTCR(156, 0xe605209c), /* PORT156CR */ - PORTCR(157, 0xe605209d), /* PORT157CR */ - PORTCR(158, 0xe605209e), /* PORT158CR */ - PORTCR(159, 0xe605209f), /* PORT159CR */ - - PORTCR(160, 0xe60520a0), /* PORT160CR */ - PORTCR(161, 0xe60520a1), /* PORT161CR */ - PORTCR(162, 0xe60520a2), /* PORT162CR */ - PORTCR(163, 0xe60520a3), /* PORT163CR */ - PORTCR(164, 0xe60520a4), /* PORT164CR */ - - PORTCR(192, 0xe60520c0), /* PORT192CR */ - PORTCR(193, 0xe60520c1), /* PORT193CR */ - PORTCR(194, 0xe60520c2), /* PORT194CR */ - PORTCR(195, 0xe60520c3), /* PORT195CR */ - PORTCR(196, 0xe60520c4), /* PORT196CR */ - PORTCR(197, 0xe60520c5), /* PORT197CR */ - PORTCR(198, 0xe60520c6), /* PORT198CR */ - PORTCR(199, 0xe60520c7), /* PORT199CR */ - - PORTCR(200, 0xe60520c8), /* PORT200CR */ - PORTCR(201, 0xe60520c9), /* PORT201CR */ - PORTCR(202, 0xe60520ca), /* PORT202CR */ - PORTCR(203, 0xe60520cb), /* PORT203CR */ - PORTCR(204, 0xe60520cc), /* PORT204CR */ - PORTCR(205, 0xe60520cd), /* PORT205CR */ - PORTCR(206, 0xe60520ce), /* PORT206CR */ - PORTCR(207, 0xe60520cf), /* PORT207CR */ - PORTCR(208, 0xe60520d0), /* PORT208CR */ - PORTCR(209, 0xe60520d1), /* PORT209CR */ - - PORTCR(210, 0xe60520d2), /* PORT210CR */ - PORTCR(211, 0xe60520d3), /* PORT211CR */ - PORTCR(212, 0xe60520d4), /* PORT212CR */ - PORTCR(213, 0xe60520d5), /* PORT213CR */ - PORTCR(214, 0xe60520d6), /* PORT214CR */ - PORTCR(215, 0xe60520d7), /* PORT215CR */ - PORTCR(216, 0xe60520d8), /* PORT216CR */ - PORTCR(217, 0xe60520d9), /* PORT217CR */ - PORTCR(218, 0xe60520da), /* PORT218CR */ - PORTCR(219, 0xe60520db), /* PORT219CR */ - - PORTCR(220, 0xe60520dc), /* PORT220CR */ - PORTCR(221, 0xe60520dd), /* PORT221CR */ - PORTCR(222, 0xe60520de), /* PORT222CR */ - PORTCR(223, 0xe60520df), /* PORT223CR */ - PORTCR(224, 0xe60530e0), /* PORT224CR */ - PORTCR(225, 0xe60530e1), /* PORT225CR */ - PORTCR(226, 0xe60530e2), /* PORT226CR */ - PORTCR(227, 0xe60530e3), /* PORT227CR */ - PORTCR(228, 0xe60530e4), /* PORT228CR */ - PORTCR(229, 0xe60530e5), /* PORT229CR */ - - PORTCR(230, 0xe60530e6), /* PORT230CR */ - PORTCR(231, 0xe60530e7), /* PORT231CR */ - PORTCR(232, 0xe60530e8), /* PORT232CR */ - PORTCR(233, 0xe60530e9), /* PORT233CR */ - PORTCR(234, 0xe60530ea), /* PORT234CR */ - PORTCR(235, 0xe60530eb), /* PORT235CR */ - PORTCR(236, 0xe60530ec), /* PORT236CR */ - PORTCR(237, 0xe60530ed), /* PORT237CR */ - PORTCR(238, 0xe60530ee), /* PORT238CR */ - PORTCR(239, 0xe60530ef), /* PORT239CR */ - - PORTCR(240, 0xe60530f0), /* PORT240CR */ - PORTCR(241, 0xe60530f1), /* PORT241CR */ - PORTCR(242, 0xe60530f2), /* PORT242CR */ - PORTCR(243, 0xe60530f3), /* PORT243CR */ - PORTCR(244, 0xe60530f4), /* PORT244CR */ - PORTCR(245, 0xe60530f5), /* PORT245CR */ - PORTCR(246, 0xe60530f6), /* PORT246CR */ - PORTCR(247, 0xe60530f7), /* PORT247CR */ - PORTCR(248, 0xe60530f8), /* PORT248CR */ - PORTCR(249, 0xe60530f9), /* PORT249CR */ - - PORTCR(250, 0xe60530fa), /* PORT250CR */ - PORTCR(251, 0xe60530fb), /* PORT251CR */ - PORTCR(252, 0xe60530fc), /* PORT252CR */ - PORTCR(253, 0xe60530fd), /* PORT253CR */ - PORTCR(254, 0xe60530fe), /* PORT254CR */ - PORTCR(255, 0xe60530ff), /* PORT255CR */ - PORTCR(256, 0xe6053100), /* PORT256CR */ - PORTCR(257, 0xe6053101), /* PORT257CR */ - PORTCR(258, 0xe6053102), /* PORT258CR */ - PORTCR(259, 0xe6053103), /* PORT259CR */ - - PORTCR(260, 0xe6053104), /* PORT260CR */ - PORTCR(261, 0xe6053105), /* PORT261CR */ - PORTCR(262, 0xe6053106), /* PORT262CR */ - PORTCR(263, 0xe6053107), /* PORT263CR */ - PORTCR(264, 0xe6053108), /* PORT264CR */ - PORTCR(265, 0xe6053109), /* PORT265CR */ - PORTCR(266, 0xe605310a), /* PORT266CR */ - PORTCR(267, 0xe605310b), /* PORT267CR */ - PORTCR(268, 0xe605310c), /* PORT268CR */ - PORTCR(269, 0xe605310d), /* PORT269CR */ - - PORTCR(270, 0xe605310e), /* PORT270CR */ - PORTCR(271, 0xe605310f), /* PORT271CR */ - PORTCR(272, 0xe6053110), /* PORT272CR */ - PORTCR(273, 0xe6053111), /* PORT273CR */ - PORTCR(274, 0xe6053112), /* PORT274CR */ - PORTCR(275, 0xe6053113), /* PORT275CR */ - PORTCR(276, 0xe6053114), /* PORT276CR */ - PORTCR(277, 0xe6053115), /* PORT277CR */ - PORTCR(278, 0xe6053116), /* PORT278CR */ - PORTCR(279, 0xe6053117), /* PORT279CR */ - - PORTCR(280, 0xe6053118), /* PORT280CR */ - PORTCR(281, 0xe6053119), /* PORT281CR */ - PORTCR(282, 0xe605311a), /* PORT282CR */ - - PORTCR(288, 0xe6052120), /* PORT288CR */ - PORTCR(289, 0xe6052121), /* PORT289CR */ - - PORTCR(290, 0xe6052122), /* PORT290CR */ - PORTCR(291, 0xe6052123), /* PORT291CR */ - PORTCR(292, 0xe6052124), /* PORT292CR */ - PORTCR(293, 0xe6052125), /* PORT293CR */ - PORTCR(294, 0xe6052126), /* PORT294CR */ - PORTCR(295, 0xe6052127), /* PORT295CR */ - PORTCR(296, 0xe6052128), /* PORT296CR */ - PORTCR(297, 0xe6052129), /* PORT297CR */ - PORTCR(298, 0xe605212a), /* PORT298CR */ - PORTCR(299, 0xe605212b), /* PORT299CR */ - - PORTCR(300, 0xe605212c), /* PORT300CR */ - PORTCR(301, 0xe605212d), /* PORT301CR */ - PORTCR(302, 0xe605212e), /* PORT302CR */ - PORTCR(303, 0xe605212f), /* PORT303CR */ - PORTCR(304, 0xe6052130), /* PORT304CR */ - PORTCR(305, 0xe6052131), /* PORT305CR */ - PORTCR(306, 0xe6052132), /* PORT306CR */ - PORTCR(307, 0xe6052133), /* PORT307CR */ - PORTCR(308, 0xe6052134), /* PORT308CR */ - PORTCR(309, 0xe6052135), /* PORT309CR */ - - { PINMUX_CFG_REG("MSEL2CR", 0xe605801c, 32, 1) { - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - MSEL2CR_MSEL19_0, MSEL2CR_MSEL19_1, - MSEL2CR_MSEL18_0, MSEL2CR_MSEL18_1, - MSEL2CR_MSEL17_0, MSEL2CR_MSEL17_1, - MSEL2CR_MSEL16_0, MSEL2CR_MSEL16_1, - 0, 0, - MSEL2CR_MSEL14_0, MSEL2CR_MSEL14_1, - MSEL2CR_MSEL13_0, MSEL2CR_MSEL13_1, - MSEL2CR_MSEL12_0, MSEL2CR_MSEL12_1, - MSEL2CR_MSEL11_0, MSEL2CR_MSEL11_1, - MSEL2CR_MSEL10_0, MSEL2CR_MSEL10_1, - MSEL2CR_MSEL9_0, MSEL2CR_MSEL9_1, - MSEL2CR_MSEL8_0, MSEL2CR_MSEL8_1, - MSEL2CR_MSEL7_0, MSEL2CR_MSEL7_1, - MSEL2CR_MSEL6_0, MSEL2CR_MSEL6_1, - MSEL2CR_MSEL5_0, MSEL2CR_MSEL5_1, - MSEL2CR_MSEL4_0, MSEL2CR_MSEL4_1, - MSEL2CR_MSEL3_0, MSEL2CR_MSEL3_1, - MSEL2CR_MSEL2_0, MSEL2CR_MSEL2_1, - MSEL2CR_MSEL1_0, MSEL2CR_MSEL1_1, - MSEL2CR_MSEL0_0, MSEL2CR_MSEL0_1, - } - }, - { PINMUX_CFG_REG("MSEL3CR", 0xe6058020, 32, 1) { - 0, 0, - 0, 0, - 0, 0, - MSEL3CR_MSEL28_0, MSEL3CR_MSEL28_1, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - 0, 0, - MSEL3CR_MSEL15_0, MSEL3CR_MSEL15_1, - 0, 0, - 0, 0, - 0, 0, - MSEL3CR_MSEL11_0, MSEL3CR_MSEL11_1, - 0, 0, - MSEL3CR_MSEL9_0, MSEL3CR_MSEL9_1, - 0, 0, - 0, 0, - MSEL3CR_MSEL6_0, MSEL3CR_MSEL6_1, - 0, 0, - 0, 0, - 0, 0, - MSEL3CR_MSEL2_0, MSEL3CR_MSEL2_1, - 0, 0, - 0, 0, - } - }, - { PINMUX_CFG_REG("MSEL4CR", 0xe6058024, 32, 1) { - 0, 0, - 0, 0, - MSEL4CR_MSEL29_0, MSEL4CR_MSEL29_1, - 0, 0, - MSEL4CR_MSEL27_0, MSEL4CR_MSEL27_1, - MSEL4CR_MSEL26_0, MSEL4CR_MSEL26_1, - 0, 0, - 0, 0, - 0, 0, - MSEL4CR_MSEL22_0, MSEL4CR_MSEL22_1, - MSEL4CR_MSEL21_0, MSEL4CR_MSEL21_1, - MSEL4CR_MSEL20_0, MSEL4CR_MSEL20_1, - MSEL4CR_MSEL19_0, MSEL4CR_MSEL19_1, - 0, 0, - 0, 0, - 0, 0, - MSEL4CR_MSEL15_0, MSEL4CR_MSEL15_1, - 0, 0, - MSEL4CR_MSEL13_0, MSEL4CR_MSEL13_1, - MSEL4CR_MSEL12_0, MSEL4CR_MSEL12_1, - MSEL4CR_MSEL11_0, MSEL4CR_MSEL11_1, - MSEL4CR_MSEL10_0, MSEL4CR_MSEL10_1, - MSEL4CR_MSEL9_0, MSEL4CR_MSEL9_1, - MSEL4CR_MSEL8_0, MSEL4CR_MSEL8_1, - MSEL4CR_MSEL7_0, MSEL4CR_MSEL7_1, - 0, 0, - 0, 0, - MSEL4CR_MSEL4_0, MSEL4CR_MSEL4_1, - 0, 0, - 0, 0, - MSEL4CR_MSEL1_0, MSEL4CR_MSEL1_1, - 0, 0, - } - }, - { }, -}; - -static struct pinmux_data_reg pinmux_data_regs[] = { - { PINMUX_DATA_REG("PORTL031_000DR", 0xe6054000, 32) { - PORT31_DATA, PORT30_DATA, PORT29_DATA, PORT28_DATA, - PORT27_DATA, PORT26_DATA, PORT25_DATA, PORT24_DATA, - PORT23_DATA, PORT22_DATA, PORT21_DATA, PORT20_DATA, - PORT19_DATA, PORT18_DATA, PORT17_DATA, PORT16_DATA, - PORT15_DATA, PORT14_DATA, PORT13_DATA, PORT12_DATA, - PORT11_DATA, PORT10_DATA, PORT9_DATA, PORT8_DATA, - PORT7_DATA, PORT6_DATA, PORT5_DATA, PORT4_DATA, - PORT3_DATA, PORT2_DATA, PORT1_DATA, PORT0_DATA } - }, - { PINMUX_DATA_REG("PORTD063_032DR", 0xe6055000, 32) { - PORT63_DATA, PORT62_DATA, PORT61_DATA, PORT60_DATA, - PORT59_DATA, PORT58_DATA, PORT57_DATA, PORT56_DATA, - PORT55_DATA, PORT54_DATA, PORT53_DATA, PORT52_DATA, - PORT51_DATA, PORT50_DATA, PORT49_DATA, PORT48_DATA, - PORT47_DATA, PORT46_DATA, PORT45_DATA, PORT44_DATA, - PORT43_DATA, PORT42_DATA, PORT41_DATA, PORT40_DATA, - PORT39_DATA, PORT38_DATA, PORT37_DATA, PORT36_DATA, - PORT35_DATA, PORT34_DATA, PORT33_DATA, PORT32_DATA } - }, - { PINMUX_DATA_REG("PORTD095_064DR", 0xe6055004, 32) { - PORT95_DATA, PORT94_DATA, PORT93_DATA, PORT92_DATA, - PORT91_DATA, PORT90_DATA, PORT89_DATA, PORT88_DATA, - PORT87_DATA, PORT86_DATA, PORT85_DATA, PORT84_DATA, - PORT83_DATA, PORT82_DATA, PORT81_DATA, PORT80_DATA, - PORT79_DATA, PORT78_DATA, PORT77_DATA, PORT76_DATA, - PORT75_DATA, PORT74_DATA, PORT73_DATA, PORT72_DATA, - PORT71_DATA, PORT70_DATA, PORT69_DATA, PORT68_DATA, - PORT67_DATA, PORT66_DATA, PORT65_DATA, PORT64_DATA } - }, - { PINMUX_DATA_REG("PORTR127_096DR", 0xe6056000, 32) { - 0, 0, 0, 0, - 0, 0, 0, 0, - 0, PORT118_DATA, PORT117_DATA, PORT116_DATA, - PORT115_DATA, PORT114_DATA, PORT113_DATA, PORT112_DATA, - PORT111_DATA, PORT110_DATA, PORT109_DATA, PORT108_DATA, - PORT107_DATA, PORT106_DATA, PORT105_DATA, PORT104_DATA, - PORT103_DATA, PORT102_DATA, PORT101_DATA, PORT100_DATA, - PORT99_DATA, PORT98_DATA, PORT97_DATA, PORT96_DATA } - }, - { PINMUX_DATA_REG("PORTR159_128DR", 0xe6056004, 32) { - PORT159_DATA, PORT158_DATA, PORT157_DATA, PORT156_DATA, - PORT155_DATA, PORT154_DATA, PORT153_DATA, PORT152_DATA, - PORT151_DATA, PORT150_DATA, PORT149_DATA, PORT148_DATA, - PORT147_DATA, PORT146_DATA, PORT145_DATA, PORT144_DATA, - PORT143_DATA, PORT142_DATA, PORT141_DATA, PORT140_DATA, - PORT139_DATA, PORT138_DATA, PORT137_DATA, PORT136_DATA, - PORT135_DATA, PORT134_DATA, PORT133_DATA, PORT132_DATA, - PORT131_DATA, PORT130_DATA, PORT129_DATA, PORT128_DATA } - }, - { PINMUX_DATA_REG("PORTR191_160DR", 0xe6056008, 32) { - 0, 0, 0, 0, - 0, 0, 0, 0, - 0, 0, 0, 0, - 0, 0, 0, 0, - 0, 0, 0, 0, - 0, 0, 0, 0, - 0, 0, 0, PORT164_DATA, - PORT163_DATA, PORT162_DATA, PORT161_DATA, PORT160_DATA } - }, - { PINMUX_DATA_REG("PORTR223_192DR", 0xe605600C, 32) { - PORT223_DATA, PORT222_DATA, PORT221_DATA, PORT220_DATA, - PORT219_DATA, PORT218_DATA, PORT217_DATA, PORT216_DATA, - PORT215_DATA, PORT214_DATA, PORT213_DATA, PORT212_DATA, - PORT211_DATA, PORT210_DATA, PORT209_DATA, PORT208_DATA, - PORT207_DATA, PORT206_DATA, PORT205_DATA, PORT204_DATA, - PORT203_DATA, PORT202_DATA, PORT201_DATA, PORT200_DATA, - PORT199_DATA, PORT198_DATA, PORT197_DATA, PORT196_DATA, - PORT195_DATA, PORT194_DATA, PORT193_DATA, PORT192_DATA } - }, - { PINMUX_DATA_REG("PORTU255_224DR", 0xe6057000, 32) { - PORT255_DATA, PORT254_DATA, PORT253_DATA, PORT252_DATA, - PORT251_DATA, PORT250_DATA, PORT249_DATA, PORT248_DATA, - PORT247_DATA, PORT246_DATA, PORT245_DATA, PORT244_DATA, - PORT243_DATA, PORT242_DATA, PORT241_DATA, PORT240_DATA, - PORT239_DATA, PORT238_DATA, PORT237_DATA, PORT236_DATA, - PORT235_DATA, PORT234_DATA, PORT233_DATA, PORT232_DATA, - PORT231_DATA, PORT230_DATA, PORT229_DATA, PORT228_DATA, - PORT227_DATA, PORT226_DATA, PORT225_DATA, PORT224_DATA } - }, - { PINMUX_DATA_REG("PORTU287_256DR", 0xe6057004, 32) { - 0, 0, 0, 0, - 0, PORT282_DATA, PORT281_DATA, PORT280_DATA, - PORT279_DATA, PORT278_DATA, PORT277_DATA, PORT276_DATA, - PORT275_DATA, PORT274_DATA, PORT273_DATA, PORT272_DATA, - PORT271_DATA, PORT270_DATA, PORT269_DATA, PORT268_DATA, - PORT267_DATA, PORT266_DATA, PORT265_DATA, PORT264_DATA, - PORT263_DATA, PORT262_DATA, PORT261_DATA, PORT260_DATA, - PORT259_DATA, PORT258_DATA, PORT257_DATA, PORT256_DATA } - }, - { PINMUX_DATA_REG("PORTR319_288DR", 0xe6056010, 32) { - 0, 0, 0, 0, - 0, 0, 0, 0, - 0, 0, PORT309_DATA, PORT308_DATA, - PORT307_DATA, PORT306_DATA, PORT305_DATA, PORT304_DATA, - PORT303_DATA, PORT302_DATA, PORT301_DATA, PORT300_DATA, - PORT299_DATA, PORT298_DATA, PORT297_DATA, PORT296_DATA, - PORT295_DATA, PORT294_DATA, PORT293_DATA, PORT292_DATA, - PORT291_DATA, PORT290_DATA, PORT289_DATA, PORT288_DATA } - }, - { }, -}; - -#if 0 -/* IRQ pins through INTCS with IRQ0->15 from 0x200 and IRQ16-31 from 0x3200 */ -#define EXT_IRQ16L(n) intcs_evt2irq(0x200 + ((n) << 5)) -#define EXT_IRQ16H(n) intcs_evt2irq(0x3200 + ((n - 16) << 5)) -#else -#define EXT_IRQ16L(n) (n) -#define EXT_IRQ16H(n) (n) -#endif - -static struct pinmux_irq pinmux_irqs[] = { - PINMUX_IRQ(EXT_IRQ16H(19), PORT9_FN0), - PINMUX_IRQ(EXT_IRQ16L(1), PORT10_FN0), - PINMUX_IRQ(EXT_IRQ16L(0), PORT11_FN0), - PINMUX_IRQ(EXT_IRQ16H(18), PORT13_FN0), - PINMUX_IRQ(EXT_IRQ16H(20), PORT14_FN0), - PINMUX_IRQ(EXT_IRQ16H(21), PORT15_FN0), - PINMUX_IRQ(EXT_IRQ16H(31), PORT26_FN0), - PINMUX_IRQ(EXT_IRQ16H(30), PORT27_FN0), - PINMUX_IRQ(EXT_IRQ16H(29), PORT28_FN0), - PINMUX_IRQ(EXT_IRQ16H(22), PORT40_FN0), - PINMUX_IRQ(EXT_IRQ16H(23), PORT53_FN0), - PINMUX_IRQ(EXT_IRQ16L(10), PORT54_FN0), - PINMUX_IRQ(EXT_IRQ16L(9), PORT56_FN0), - PINMUX_IRQ(EXT_IRQ16H(26), PORT115_FN0), - PINMUX_IRQ(EXT_IRQ16H(27), PORT116_FN0), - PINMUX_IRQ(EXT_IRQ16H(28), PORT117_FN0), - PINMUX_IRQ(EXT_IRQ16H(24), PORT118_FN0), - PINMUX_IRQ(EXT_IRQ16L(6), PORT147_FN0), - PINMUX_IRQ(EXT_IRQ16L(2), PORT149_FN0), - PINMUX_IRQ(EXT_IRQ16L(7), PORT150_FN0), - PINMUX_IRQ(EXT_IRQ16L(12), PORT156_FN0), - PINMUX_IRQ(EXT_IRQ16L(4), PORT159_FN0), - PINMUX_IRQ(EXT_IRQ16H(25), PORT164_FN0), - PINMUX_IRQ(EXT_IRQ16L(8), PORT223_FN0), - PINMUX_IRQ(EXT_IRQ16L(3), PORT224_FN0), - PINMUX_IRQ(EXT_IRQ16L(5), PORT227_FN0), - PINMUX_IRQ(EXT_IRQ16H(17), PORT234_FN0), - PINMUX_IRQ(EXT_IRQ16L(11), PORT238_FN0), - PINMUX_IRQ(EXT_IRQ16L(13), PORT239_FN0), - PINMUX_IRQ(EXT_IRQ16H(16), PORT249_FN0), - PINMUX_IRQ(EXT_IRQ16L(14), PORT251_FN0), - PINMUX_IRQ(EXT_IRQ16L(9), PORT308_FN0), -}; - -static struct pinmux_info sh73a0_pinmux_info = { - .name = "sh73a0_pfc", - .reserved_id = PINMUX_RESERVED, - .data = { PINMUX_DATA_BEGIN, PINMUX_DATA_END }, - .input = { PINMUX_INPUT_BEGIN, PINMUX_INPUT_END }, - .input_pu = { PINMUX_INPUT_PULLUP_BEGIN, PINMUX_INPUT_PULLUP_END }, - .input_pd = { PINMUX_INPUT_PULLDOWN_BEGIN, PINMUX_INPUT_PULLDOWN_END }, - .output = { PINMUX_OUTPUT_BEGIN, PINMUX_OUTPUT_END }, - .mark = { PINMUX_MARK_BEGIN, PINMUX_MARK_END }, - .function = { PINMUX_FUNCTION_BEGIN, PINMUX_FUNCTION_END }, - - .first_gpio = GPIO_PORT0, - .last_gpio = GPIO_FN_FSIAISLD_PU, - - .gpios = pinmux_gpios, - .cfg_regs = pinmux_config_regs, - .data_regs = pinmux_data_regs, - - .gpio_data = pinmux_data, - .gpio_data_size = ARRAY_SIZE(pinmux_data), - - .gpio_irq = pinmux_irqs, - .gpio_irq_size = ARRAY_SIZE(pinmux_irqs), -}; - -void sh73a0_pinmux_init(void) -{ - register_pinmux(&sh73a0_pinmux_info); -} diff --git a/drivers/i2c/sh_i2c.c b/drivers/i2c/sh_i2c.c index 6cecec41450..3335d9482a2 100644 --- a/drivers/i2c/sh_i2c.c +++ b/drivers/i2c/sh_i2c.c @@ -172,14 +172,9 @@ static int sh_i2c_raw_read(struct sh_i2c *dev, u8 chip, u8 addr) { int ret = -1; -#if defined(CONFIG_SH73A0) - if (sh_i2c_set_addr(dev, chip, addr, 0) != 0) - goto exit0; -#else if (sh_i2c_set_addr(dev, chip, addr, 1) != 0) goto exit0; udelay(100); -#endif writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS|SH_I2C_ICCR_BUSY), &dev->iccr); sh_irq_dte(dev); diff --git a/drivers/serial/serial_sh.h b/drivers/serial/serial_sh.h index e6ab6f1b9b7..660aaab6638 100644 --- a/drivers/serial/serial_sh.h +++ b/drivers/serial/serial_sh.h @@ -13,7 +13,6 @@ struct uart_port { }; #if defined(CONFIG_CPU_SH7721) || \ - defined(CONFIG_SH73A0) || \ defined(CONFIG_R8A7740) # define SCSCR_INIT(port) 0x0030 /* TIE=0,RIE=0,TE=1,RE=1 */ # define PORT_PTCR 0xA405011EUL @@ -149,7 +148,6 @@ struct uart_port { #define SCIF_DR 0x0001 /* 7705 SCIF, 7707 SCIF, 7709 SCIF, 7750 SCIF */ #if defined(CONFIG_CPU_SH7721) || \ - defined(CONFIG_SH73A0) || \ defined(CONFIG_R8A7740) # define SCIF_ORER 0x0200 # define SCIF_ERRORS (SCIF_PER | SCIF_FER | SCIF_ER | SCIF_BRK | SCIF_ORER) @@ -197,7 +195,6 @@ struct uart_port { (((port)->type == PORT_SCI) ? SCI_ORER : SCIF_ORER) #if defined(CONFIG_CPU_SH7721) || \ - defined(CONFIG_SH73A0) || \ defined(CONFIG_R8A7740) # define SCxSR_RDxF_CLEAR(port) (sci_in(port, SCxSR) & 0xfffc) # define SCxSR_ERROR_CLEAR(port) (sci_in(port, SCxSR) & 0xfd73) @@ -278,8 +275,7 @@ static inline void sci_##name##_out(struct uart_port *port,\ SCI_OUT(sci_size, sci_offset, value);\ } -#if defined(CONFIG_SH73A0) || \ - defined(CONFIG_R8A7740) +#if defined(CONFIG_R8A7740) #if defined(CONFIG_CPU_SH7721) || \ defined(CONFIG_SH73A0) #define SCIF_FNS(name, scif_offset, scif_size) \ @@ -323,8 +319,7 @@ static inline void sci_##name##_out(struct uart_port *port,\ CPU_SCIF_FNS(name, sh4_scif_offset, sh4_scif_size) #endif -#if defined(CONFIG_CPU_SH7721) || \ - defined(CONFIG_SH73A0) +#if defined(CONFIG_CPU_SH7721) SCIF_FNS(SCSMR, 0x00, 16) SCIF_FNS(SCBRR, 0x04, 8) @@ -477,7 +472,6 @@ static inline int sci_rxd_in(struct uart_port *port) #if defined(CONFIG_CPU_SH7780) #define SCBRR_VALUE(bps, clk) ((clk+16*bps)/(16*bps)-1) #elif defined(CONFIG_CPU_SH7721) || \ - defined(CONFIG_SH73A0) || \ defined(CONFIG_R8A7740) #define SCBRR_VALUE(bps, clk) (((clk*2)+16*bps)/(32*bps)-1) #elif defined(CONFIG_CPU_SH7723) -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 57/76] sh4: Drop unused pci_sh7780 driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (53 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 56/76] rmobile: Drop CONFIG_SH73A0 and associated code Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 58/76] Drop ubsha1 tool Simon Glass ` (17 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used. Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) arch/sh/include/asm/pci.h | 2 - drivers/pci/Makefile | 1 - drivers/pci/pci_sh7780.c | 92 --------------------------------------- 3 files changed, 95 deletions(-) delete mode 100644 drivers/pci/pci_sh7780.c diff --git a/arch/sh/include/asm/pci.h b/arch/sh/include/asm/pci.h index 5d79d0ec58e..18b95ff5cfb 100644 --- a/arch/sh/include/asm/pci.h +++ b/arch/sh/include/asm/pci.h @@ -13,8 +13,6 @@ #include <pci.h> #if defined(CONFIG_SH7751_PCI) int pci_sh7751_init(struct pci_controller *hose); -#elif defined(CONFIG_SH7780_PCI) -int pci_sh7780_init(struct pci_controller *hose); #else #error "Not support PCI." #endif diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile index d393f1ba031..49506e7ba59 100644 --- a/drivers/pci/Makefile +++ b/drivers/pci/Makefile @@ -22,7 +22,6 @@ obj-$(CONFIG_PCI_MVEBU) += pci_mvebu.o obj-$(CONFIG_PCI_RCAR_GEN2) += pci-rcar-gen2.o obj-$(CONFIG_PCI_RCAR_GEN3) += pci-rcar-gen3.o obj-$(CONFIG_SH7751_PCI) +=pci_sh7751.o -obj-$(CONFIG_SH7780_PCI) +=pci_sh7780.o obj-$(CONFIG_PCI_TEGRA) += pci_tegra.o obj-$(CONFIG_PCIE_IPROC) += pcie_iproc.o obj-$(CONFIG_PCI_AARDVARK) += pci-aardvark.o diff --git a/drivers/pci/pci_sh7780.c b/drivers/pci/pci_sh7780.c deleted file mode 100644 index 7533286c015..00000000000 --- a/drivers/pci/pci_sh7780.c +++ /dev/null @@ -1,92 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * SH7780 PCI Controller (PCIC) for U-Boot. - * (C) Dustin McIntire (dustin@sensoria.com) - * (C) 2007,2008 Nobuhiro Iwamatsu <iwamatsu@nigauri.org> - * (C) 2008 Yusuke Goda <goda.yusuke@renesas.com> - */ - -#include <common.h> -#include <linux/delay.h> - -#include <pci.h> -#include <asm/processor.h> -#include <asm/pci.h> -#include <asm/io.h> - -#define SH7780_VENDOR_ID 0x1912 -#define SH7780_DEVICE_ID 0x0002 -#define SH7780_PCICR_PREFIX 0xA5000000 -#define SH7780_PCICR_PFCS 0x00000800 -#define SH7780_PCICR_FTO 0x00000400 -#define SH7780_PCICR_PFE 0x00000200 -#define SH7780_PCICR_TBS 0x00000100 -#define SH7780_PCICR_ARBM 0x00000040 -#define SH7780_PCICR_IOCS 0x00000004 -#define SH7780_PCICR_PRST 0x00000002 -#define SH7780_PCICR_CFIN 0x00000001 - -#define p4_in(addr) (*(vu_long *)addr) -#define p4_out(data, addr) (*(vu_long *)addr) = (data) -#define p4_inw(addr) (*(vu_short *)addr) -#define p4_outw(data, addr) (*(vu_short *)addr) = (data) - -int pci_sh4_read_config_dword(struct pci_controller *hose, - pci_dev_t dev, int offset, u32 *value) -{ - u32 par_data = PCI_CONF1_ADDRESS(PCI_BUS(dev), PCI_DEV(dev), PCI_FUNC(dev), offset); - - p4_out(par_data, SH7780_PCIPAR); - *value = p4_in(SH7780_PCIPDR); - - return 0; -} - -int pci_sh4_write_config_dword(struct pci_controller *hose, - pci_dev_t dev, int offset, u32 value) -{ - u32 par_data = PCI_CONF1_ADDRESS(PCI_BUS(dev), PCI_DEV(dev), PCI_FUNC(dev), offset); - - p4_out(par_data, SH7780_PCIPAR); - p4_out(value, SH7780_PCIPDR); - return 0; -} - -int pci_sh7780_init(struct pci_controller *hose) -{ - p4_out(0x01, SH7780_PCIECR); - - if (p4_inw(SH7780_PCIVID) != SH7780_VENDOR_ID - && p4_inw(SH7780_PCIDID) != SH7780_DEVICE_ID) { - printf("PCI: Unknown PCI host bridge.\n"); - return -1; - } - printf("PCI: SH7780 PCI host bridge found.\n"); - - /* Toggle PCI reset pin */ - p4_out((SH7780_PCICR_PREFIX | SH7780_PCICR_PRST), SH7780_PCICR); - udelay(100000); - p4_out(SH7780_PCICR_PREFIX, SH7780_PCICR); - p4_outw(0x0047, SH7780_PCICMD); - - p4_out(CONFIG_SH7780_PCI_LSR, SH7780_PCILSR0); - p4_out(CONFIG_SH7780_PCI_LAR, SH7780_PCILAR0); - p4_out(0x00000000, SH7780_PCILSR1); - p4_out(0, SH7780_PCILAR1); - p4_out(CONFIG_SH7780_PCI_BAR, SH7780_PCIMBAR0); - p4_out(0x00000000, SH7780_PCIMBAR1); - - p4_out(0xFD000000, SH7780_PCIMBR0); - p4_out(0x00FC0000, SH7780_PCIMBMR0); - - /* if use Operand Cache then enable PCICSCR Soonp bits. */ - p4_out(0x08000000, SH7780_PCICSAR0); - p4_out(0x0000001B, SH7780_PCICSCR0); /* Snoop bit :On */ - - p4_out((SH7780_PCICR_PREFIX | SH7780_PCICR_CFIN | SH7780_PCICR_ARBM - | SH7780_PCICR_FTO | SH7780_PCICR_PFCS | SH7780_PCICR_PFE), - SH7780_PCICR); - - pci_sh4_init(hose); - return 0; -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 58/76] Drop ubsha1 tool 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (54 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 57/76] sh4: Drop unused pci_sh7780 driver Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-20 10:16 ` Peter Robinson 2023-02-01 20:20 ` [PATCH v3 59/76] sysreset: at91: Correct Makefile rule for SYSRESET_AT91 Simon Glass ` (16 subsequent siblings) 72 siblings, 1 reply; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This seems to have been used by ppc4xx which was removed a while back. The Kconfig does not exist so it is never built. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) Makefile | 3 -- tools/.gitignore | 1 - tools/Makefile | 6 ---- tools/ubsha1.c | 83 ------------------------------------------------ 4 files changed, 93 deletions(-) delete mode 100644 tools/ubsha1.c diff --git a/Makefile b/Makefile index 73a562a26de..2c9e27ac5c2 100644 --- a/Makefile +++ b/Makefile @@ -1450,9 +1450,6 @@ u-boot-with-spl.kwb: u-boot.bin spl/u-boot-spl.bin FORCE $(call if_changed,mkimage) $(BOARD_SIZE_CHECK) -u-boot.sha1: u-boot.bin - tools/ubsha1 u-boot.bin - u-boot.dis: u-boot $(OBJDUMP) -d $< > $@ diff --git a/tools/.gitignore b/tools/.gitignore index 28e8ce2a07a..788ea260a07 100644 --- a/tools/.gitignore +++ b/tools/.gitignore @@ -33,7 +33,6 @@ /relocate-rela /spl_size_limit /sunxi-spl-image-builder -/ubsha1 /update_octeon_header /version.h /xway-swap-bytes diff --git a/tools/Makefile b/tools/Makefile index 2ee43dff542..0eadd8154a7 100644 --- a/tools/Makefile +++ b/tools/Makefile @@ -29,7 +29,6 @@ CONFIG_CMD_LOADS = y CONFIG_CMD_NET = y CONFIG_XWAY_SWAP_BYTES = y CONFIG_NETCONSOLE = y -CONFIG_SHA1_CHECK_UB_IMG = y CONFIG_ARCH_SUNXI = y endif @@ -217,11 +216,6 @@ hostprogs-$(CONFIG_ARCH_SUNXI) += sunxi-spl-image-builder sunxi-spl-image-builder-objs := sunxi-spl-image-builder.o lib/bch.o hostprogs-$(CONFIG_NETCONSOLE) += ncb -hostprogs-$(CONFIG_SHA1_CHECK_UB_IMG) += ubsha1 - -ubsha1-objs := os_support.o ubsha1.o lib/sha1.o - -HOSTCFLAGS_ubsha1.o := -pedantic hostprogs-$(CONFIG_ARCH_KIRKWOOD) += kwboot hostprogs-$(CONFIG_ARCH_MVEBU) += kwboot diff --git a/tools/ubsha1.c b/tools/ubsha1.c deleted file mode 100644 index 90a6f3f59d2..00000000000 --- a/tools/ubsha1.c +++ /dev/null @@ -1,83 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2007 - * Heiko Schocher, DENX Software Engineering, <hs@denx.de> - */ - -#include "os_support.h" -#include <stdio.h> -#include <stdlib.h> -#include <unistd.h> -#include <fcntl.h> -#include <errno.h> -#include <string.h> -#include <sys/stat.h> -#include <u-boot/sha1.h> - -int main (int argc, char **argv) -{ - unsigned char output[20]; - int i, len; - - char *imagefile; - char *cmdname = *argv; - unsigned char *ptr; - unsigned char *data; - struct stat sbuf; - unsigned char *ptroff; - int ifd; - int off; - - if (argc > 1) { - imagefile = argv[1]; - ifd = open (imagefile, O_RDWR|O_BINARY); - if (ifd < 0) { - fprintf (stderr, "%s: Can't open %s: %s\n", - cmdname, imagefile, strerror(errno)); - exit (EXIT_FAILURE); - } - if (fstat (ifd, &sbuf) < 0) { - fprintf (stderr, "%s: Can't stat %s: %s\n", - cmdname, imagefile, strerror(errno)); - exit (EXIT_FAILURE); - } - len = sbuf.st_size; - ptr = (unsigned char *)mmap(0, len, - PROT_READ, MAP_SHARED, ifd, 0); - if (ptr == (unsigned char *)MAP_FAILED) { - fprintf (stderr, "%s: Can't read %s: %s\n", - cmdname, imagefile, strerror(errno)); - exit (EXIT_FAILURE); - } - - /* create a copy, so we can blank out the sha1 sum */ - data = malloc (len); - memcpy (data, ptr, len); - off = SHA1_SUM_POS; - ptroff = &data[len + off]; - for (i = 0; i < SHA1_SUM_LEN; i++) { - ptroff[i] = 0; - } - - sha1_csum ((unsigned char *) data, len, (unsigned char *)output); - - printf ("U-Boot sum:\n"); - for (i = 0; i < 20 ; i++) { - printf ("%02X ", output[i]); - } - printf ("\n"); - /* overwrite the sum in the bin file, with the actual */ - lseek (ifd, SHA1_SUM_POS, SEEK_END); - if (write (ifd, output, SHA1_SUM_LEN) != SHA1_SUM_LEN) { - fprintf (stderr, "%s: Can't write %s: %s\n", - cmdname, imagefile, strerror(errno)); - exit (EXIT_FAILURE); - } - - free (data); - (void) munmap((void *)ptr, len); - (void) close (ifd); - } - - return EXIT_SUCCESS; -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* Re: [PATCH v3 58/76] Drop ubsha1 tool 2023-02-01 20:20 ` [PATCH v3 58/76] Drop ubsha1 tool Simon Glass @ 2023-02-20 10:16 ` Peter Robinson 2023-02-21 19:41 ` Simon Glass 0 siblings, 1 reply; 87+ messages in thread From: Peter Robinson @ 2023-02-20 10:16 UTC (permalink / raw) To: Simon Glass; +Cc: u-boot, Tom Rini On Wed, Feb 1, 2023 at 8:46 PM Simon Glass <sjg@chromium.org> wrote: > > This seems to have been used by ppc4xx which was removed a while back. > The Kconfig does not exist so it is never built. Drop it. That assumption isn't entirely correct, it was at least built by the tools only/all build process. Peter > Signed-off-by: Simon Glass <sjg@chromium.org> > --- > > (no changes since v1) > > Makefile | 3 -- > tools/.gitignore | 1 - > tools/Makefile | 6 ---- > tools/ubsha1.c | 83 ------------------------------------------------ > 4 files changed, 93 deletions(-) > delete mode 100644 tools/ubsha1.c > > diff --git a/Makefile b/Makefile > index 73a562a26de..2c9e27ac5c2 100644 > --- a/Makefile > +++ b/Makefile > @@ -1450,9 +1450,6 @@ u-boot-with-spl.kwb: u-boot.bin spl/u-boot-spl.bin FORCE > $(call if_changed,mkimage) > $(BOARD_SIZE_CHECK) > > -u-boot.sha1: u-boot.bin > - tools/ubsha1 u-boot.bin > - > u-boot.dis: u-boot > $(OBJDUMP) -d $< > $@ > > diff --git a/tools/.gitignore b/tools/.gitignore > index 28e8ce2a07a..788ea260a07 100644 > --- a/tools/.gitignore > +++ b/tools/.gitignore > @@ -33,7 +33,6 @@ > /relocate-rela > /spl_size_limit > /sunxi-spl-image-builder > -/ubsha1 > /update_octeon_header > /version.h > /xway-swap-bytes > diff --git a/tools/Makefile b/tools/Makefile > index 2ee43dff542..0eadd8154a7 100644 > --- a/tools/Makefile > +++ b/tools/Makefile > @@ -29,7 +29,6 @@ CONFIG_CMD_LOADS = y > CONFIG_CMD_NET = y > CONFIG_XWAY_SWAP_BYTES = y > CONFIG_NETCONSOLE = y > -CONFIG_SHA1_CHECK_UB_IMG = y > CONFIG_ARCH_SUNXI = y > endif > > @@ -217,11 +216,6 @@ hostprogs-$(CONFIG_ARCH_SUNXI) += sunxi-spl-image-builder > sunxi-spl-image-builder-objs := sunxi-spl-image-builder.o lib/bch.o > > hostprogs-$(CONFIG_NETCONSOLE) += ncb > -hostprogs-$(CONFIG_SHA1_CHECK_UB_IMG) += ubsha1 > - > -ubsha1-objs := os_support.o ubsha1.o lib/sha1.o > - > -HOSTCFLAGS_ubsha1.o := -pedantic > > hostprogs-$(CONFIG_ARCH_KIRKWOOD) += kwboot > hostprogs-$(CONFIG_ARCH_MVEBU) += kwboot > diff --git a/tools/ubsha1.c b/tools/ubsha1.c > deleted file mode 100644 > index 90a6f3f59d2..00000000000 > --- a/tools/ubsha1.c > +++ /dev/null > @@ -1,83 +0,0 @@ > -// SPDX-License-Identifier: GPL-2.0+ > -/* > - * (C) Copyright 2007 > - * Heiko Schocher, DENX Software Engineering, <hs@denx.de> > - */ > - > -#include "os_support.h" > -#include <stdio.h> > -#include <stdlib.h> > -#include <unistd.h> > -#include <fcntl.h> > -#include <errno.h> > -#include <string.h> > -#include <sys/stat.h> > -#include <u-boot/sha1.h> > - > -int main (int argc, char **argv) > -{ > - unsigned char output[20]; > - int i, len; > - > - char *imagefile; > - char *cmdname = *argv; > - unsigned char *ptr; > - unsigned char *data; > - struct stat sbuf; > - unsigned char *ptroff; > - int ifd; > - int off; > - > - if (argc > 1) { > - imagefile = argv[1]; > - ifd = open (imagefile, O_RDWR|O_BINARY); > - if (ifd < 0) { > - fprintf (stderr, "%s: Can't open %s: %s\n", > - cmdname, imagefile, strerror(errno)); > - exit (EXIT_FAILURE); > - } > - if (fstat (ifd, &sbuf) < 0) { > - fprintf (stderr, "%s: Can't stat %s: %s\n", > - cmdname, imagefile, strerror(errno)); > - exit (EXIT_FAILURE); > - } > - len = sbuf.st_size; > - ptr = (unsigned char *)mmap(0, len, > - PROT_READ, MAP_SHARED, ifd, 0); > - if (ptr == (unsigned char *)MAP_FAILED) { > - fprintf (stderr, "%s: Can't read %s: %s\n", > - cmdname, imagefile, strerror(errno)); > - exit (EXIT_FAILURE); > - } > - > - /* create a copy, so we can blank out the sha1 sum */ > - data = malloc (len); > - memcpy (data, ptr, len); > - off = SHA1_SUM_POS; > - ptroff = &data[len + off]; > - for (i = 0; i < SHA1_SUM_LEN; i++) { > - ptroff[i] = 0; > - } > - > - sha1_csum ((unsigned char *) data, len, (unsigned char *)output); > - > - printf ("U-Boot sum:\n"); > - for (i = 0; i < 20 ; i++) { > - printf ("%02X ", output[i]); > - } > - printf ("\n"); > - /* overwrite the sum in the bin file, with the actual */ > - lseek (ifd, SHA1_SUM_POS, SEEK_END); > - if (write (ifd, output, SHA1_SUM_LEN) != SHA1_SUM_LEN) { > - fprintf (stderr, "%s: Can't write %s: %s\n", > - cmdname, imagefile, strerror(errno)); > - exit (EXIT_FAILURE); > - } > - > - free (data); > - (void) munmap((void *)ptr, len); > - (void) close (ifd); > - } > - > - return EXIT_SUCCESS; > -} > -- > 2.39.1.456.gfc5497dd1b-goog > ^ permalink raw reply [flat|nested] 87+ messages in thread
* Re: [PATCH v3 58/76] Drop ubsha1 tool 2023-02-20 10:16 ` Peter Robinson @ 2023-02-21 19:41 ` Simon Glass 2023-02-22 8:08 ` Peter Robinson 0 siblings, 1 reply; 87+ messages in thread From: Simon Glass @ 2023-02-21 19:41 UTC (permalink / raw) To: Peter Robinson; +Cc: u-boot, Tom Rini Hi Peter, On Mon, 20 Feb 2023 at 03:16, Peter Robinson <pbrobinson@gmail.com> wrote: > > On Wed, Feb 1, 2023 at 8:46 PM Simon Glass <sjg@chromium.org> wrote: > > > > This seems to have been used by ppc4xx which was removed a while back. > > The Kconfig does not exist so it is never built. Drop it. > > That assumption isn't entirely correct, it was at least built by the > tools only/all build process. Oh yes, I perhaps meant that it isn't used. Is it OK to delete it? Regards, Simon ^ permalink raw reply [flat|nested] 87+ messages in thread
* Re: [PATCH v3 58/76] Drop ubsha1 tool 2023-02-21 19:41 ` Simon Glass @ 2023-02-22 8:08 ` Peter Robinson 2023-02-22 21:20 ` Simon Glass 0 siblings, 1 reply; 87+ messages in thread From: Peter Robinson @ 2023-02-22 8:08 UTC (permalink / raw) To: Simon Glass; +Cc: u-boot, Tom Rini On Tue, Feb 21, 2023 at 7:42 PM Simon Glass <sjg@chromium.org> wrote: > > Hi Peter, > > On Mon, 20 Feb 2023 at 03:16, Peter Robinson <pbrobinson@gmail.com> wrote: > > > > On Wed, Feb 1, 2023 at 8:46 PM Simon Glass <sjg@chromium.org> wrote: > > > > > > This seems to have been used by ppc4xx which was removed a while back. > > > The Kconfig does not exist so it is never built. Drop it. > > > > That assumption isn't entirely correct, it was at least built by the > > tools only/all build process. > > Oh yes, I perhaps meant that it isn't used. > > Is it OK to delete it? I think so, I just wanted to verify that it was built in other circumstances in case that mattered. P ^ permalink raw reply [flat|nested] 87+ messages in thread
* Re: [PATCH v3 58/76] Drop ubsha1 tool 2023-02-22 8:08 ` Peter Robinson @ 2023-02-22 21:20 ` Simon Glass 0 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-22 21:20 UTC (permalink / raw) To: Peter Robinson; +Cc: u-boot, Tom Rini Hi Peter, On Wed, 22 Feb 2023 at 01:08, Peter Robinson <pbrobinson@gmail.com> wrote: > > On Tue, Feb 21, 2023 at 7:42 PM Simon Glass <sjg@chromium.org> wrote: > > > > Hi Peter, > > > > On Mon, 20 Feb 2023 at 03:16, Peter Robinson <pbrobinson@gmail.com> wrote: > > > > > > On Wed, Feb 1, 2023 at 8:46 PM Simon Glass <sjg@chromium.org> wrote: > > > > > > > > This seems to have been used by ppc4xx which was removed a while back. > > > > The Kconfig does not exist so it is never built. Drop it. > > > > > > That assumption isn't entirely correct, it was at least built by the > > > tools only/all build process. > > > > Oh yes, I perhaps meant that it isn't used. > > > > Is it OK to delete it? > > I think so, I just wanted to verify that it was built in other > circumstances in case that mattered. OK thank you. Regards, Simon ^ permalink raw reply [flat|nested] 87+ messages in thread
* [PATCH v3 59/76] sysreset: at91: Correct Makefile rule for SYSRESET_AT91 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (55 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 58/76] Drop ubsha1 tool Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 60/76] gdsys: Drop unused fpga file Simon Glass ` (15 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Claudiu Beznea, Andreas Bießmann The SPL_TPL part is in the wrong place. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org> Fixes: 71d4393f846 ("sysreset: Add Atmel/Microchip sysreset driver") Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> --- (no changes since v1) drivers/sysreset/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/sysreset/Makefile b/drivers/sysreset/Makefile index 0ed3bbf356a..40c876764af 100644 --- a/drivers/sysreset/Makefile +++ b/drivers/sysreset/Makefile @@ -20,6 +20,6 @@ obj-$(CONFIG_SYSRESET_TI_SCI) += sysreset-ti-sci.o obj-$(CONFIG_SYSRESET_SYSCON) += sysreset_syscon.o obj-$(CONFIG_SYSRESET_WATCHDOG) += sysreset_watchdog.o obj-$(CONFIG_SYSRESET_RESETCTL) += sysreset_resetctl.o -obj-$(CONFIG_SYSRESET_$(SPL_TPL_)AT91) += sysreset_at91.o +obj-$(CONFIG_$(SPL_TPL_)SYSRESET_AT91) += sysreset_at91.o obj-$(CONFIG_$(SPL_TPL_)SYSRESET_X86) += sysreset_x86.o obj-$(CONFIG_TARGET_XTFPGA) += sysreset_xtfpga.o -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 60/76] gdsys: Drop unused fpga file 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (56 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 59/76] sysreset: at91: Correct Makefile rule for SYSRESET_AT91 Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 61/76] sh4: Drop unused kona_i2c driver Simon Glass ` (14 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used since CONFIG_SYS_FPGA_COMMON is not defined anywhere. Drop the code and the Makefile rule. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) board/gdsys/common/Makefile | 1 - board/gdsys/common/fpga.c | 28 ---------------------------- 2 files changed, 29 deletions(-) delete mode 100644 board/gdsys/common/fpga.c diff --git a/board/gdsys/common/Makefile b/board/gdsys/common/Makefile index 553e2ca50ed..94cbf3c5cc1 100644 --- a/board/gdsys/common/Makefile +++ b/board/gdsys/common/Makefile @@ -3,7 +3,6 @@ # (C) Copyright 2007 # Stefan Roese, DENX Software Engineering, sr@denx.de. -obj-$(CONFIG_SYS_FPGA_COMMON) += fpga.o obj-$(CONFIG_CMD_IOLOOP) += cmd_ioloop.o obj-$(CONFIG_TARGET_CONTROLCENTERDC) += dp501.o obj-$(CONFIG_TARGET_GAZERBEAM) += osd.o ihs_mdio.o ioep-fpga.o diff --git a/board/gdsys/common/fpga.c b/board/gdsys/common/fpga.c deleted file mode 100644 index 5ba6613ed56..00000000000 --- a/board/gdsys/common/fpga.c +++ /dev/null @@ -1,28 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2013 - * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc - */ - -#ifdef CONFIG_GDSYS_LEGACY_DRIVERS - -#include <common.h> -#include <gdsys_fpga.h> - -#include <asm/io.h> - -int fpga_set_reg(u32 fpga, u16 *reg, off_t regoff, u16 data) -{ - out_le16(reg, data); - - return 0; -} - -int fpga_get_reg(u32 fpga, u16 *reg, off_t regoff, u16 *data) -{ - *data = in_le16(reg); - - return 0; -} - -#endif /* CONFIG_GDSYS_LEGACY_DRIVERS */ -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 61/76] sh4: Drop unused kona_i2c driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (57 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 60/76] gdsys: Drop unused fpga file Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 62/76] compulab: Drop CONFIG_TARGET_MCM_IMX8M_MINI Simon Glass ` (13 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Heiko Schocher This is not used. Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de> --- (no changes since v1) drivers/i2c/Makefile | 1 - drivers/i2c/kona_i2c.c | 728 ----------------------------------------- 2 files changed, 729 deletions(-) delete mode 100644 drivers/i2c/kona_i2c.c diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile index 920aafb91c5..cde0597290c 100644 --- a/drivers/i2c/Makefile +++ b/drivers/i2c/Makefile @@ -25,7 +25,6 @@ obj-$(CONFIG_SYS_I2C_IHS) += ihs_i2c.o obj-$(CONFIG_SYS_I2C_INTEL) += intel_i2c.o obj-$(CONFIG_SYS_I2C_IMX_LPI2C) += imx_lpi2c.o obj-$(CONFIG_SYS_I2C_IPROC) += iproc_i2c.o -obj-$(CONFIG_SYS_I2C_KONA) += kona_i2c.o obj-$(CONFIG_SYS_I2C_LPC32XX) += lpc32xx_i2c.o obj-$(CONFIG_SYS_I2C_MESON) += meson_i2c.o obj-$(CONFIG_SYS_I2C_MICROCHIP) += i2c-microchip.o diff --git a/drivers/i2c/kona_i2c.c b/drivers/i2c/kona_i2c.c deleted file mode 100644 index b9b0ff1c39e..00000000000 --- a/drivers/i2c/kona_i2c.c +++ /dev/null @@ -1,728 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2013 Broadcom Corporation. - * - * NOTE: This driver should be converted to driver model before June 2017. - * Please see doc/driver-model/i2c-howto.rst for instructions. - */ - -#include <common.h> -#include <log.h> -#include <asm/io.h> -#include <linux/delay.h> -#include <linux/errno.h> -#include <asm/arch/sysmap.h> -#include <asm/kona-common/clk.h> -#include <i2c.h> - -/* Hardware register offsets and field defintions */ -#define CS_OFFSET 0x00000020 -#define CS_ACK_SHIFT 3 -#define CS_ACK_MASK 0x00000008 -#define CS_ACK_CMD_GEN_START 0x00000000 -#define CS_ACK_CMD_GEN_RESTART 0x00000001 -#define CS_CMD_SHIFT 1 -#define CS_CMD_CMD_NO_ACTION 0x00000000 -#define CS_CMD_CMD_START_RESTART 0x00000001 -#define CS_CMD_CMD_STOP 0x00000002 -#define CS_EN_SHIFT 0 -#define CS_EN_CMD_ENABLE_BSC 0x00000001 - -#define TIM_OFFSET 0x00000024 -#define TIM_PRESCALE_SHIFT 6 -#define TIM_P_SHIFT 3 -#define TIM_NO_DIV_SHIFT 2 -#define TIM_DIV_SHIFT 0 - -#define DAT_OFFSET 0x00000028 - -#define TOUT_OFFSET 0x0000002c - -#define TXFCR_OFFSET 0x0000003c -#define TXFCR_FIFO_FLUSH_MASK 0x00000080 -#define TXFCR_FIFO_EN_MASK 0x00000040 - -#define IER_OFFSET 0x00000044 -#define IER_READ_COMPLETE_INT_MASK 0x00000010 -#define IER_I2C_INT_EN_MASK 0x00000008 -#define IER_FIFO_INT_EN_MASK 0x00000002 -#define IER_NOACK_EN_MASK 0x00000001 - -#define ISR_OFFSET 0x00000048 -#define ISR_RESERVED_MASK 0xffffff60 -#define ISR_CMDBUSY_MASK 0x00000080 -#define ISR_READ_COMPLETE_MASK 0x00000010 -#define ISR_SES_DONE_MASK 0x00000008 -#define ISR_ERR_MASK 0x00000004 -#define ISR_TXFIFOEMPTY_MASK 0x00000002 -#define ISR_NOACK_MASK 0x00000001 - -#define CLKEN_OFFSET 0x0000004c -#define CLKEN_AUTOSENSE_OFF_MASK 0x00000080 -#define CLKEN_M_SHIFT 4 -#define CLKEN_N_SHIFT 1 -#define CLKEN_CLKEN_MASK 0x00000001 - -#define FIFO_STATUS_OFFSET 0x00000054 -#define FIFO_STATUS_RXFIFO_EMPTY_MASK 0x00000004 -#define FIFO_STATUS_TXFIFO_EMPTY_MASK 0x00000010 - -#define HSTIM_OFFSET 0x00000058 -#define HSTIM_HS_MODE_MASK 0x00008000 -#define HSTIM_HS_HOLD_SHIFT 10 -#define HSTIM_HS_HIGH_PHASE_SHIFT 5 -#define HSTIM_HS_SETUP_SHIFT 0 - -#define PADCTL_OFFSET 0x0000005c -#define PADCTL_PAD_OUT_EN_MASK 0x00000004 - -#define RXFCR_OFFSET 0x00000068 -#define RXFCR_NACK_EN_SHIFT 7 -#define RXFCR_READ_COUNT_SHIFT 0 -#define RXFIFORDOUT_OFFSET 0x0000006c - -/* Locally used constants */ -#define MAX_RX_FIFO_SIZE 64U /* bytes */ -#define MAX_TX_FIFO_SIZE 64U /* bytes */ - -#define I2C_TIMEOUT 100000 /* usecs */ - -#define WAIT_INT_CHK 100 /* usecs */ -#if I2C_TIMEOUT % WAIT_INT_CHK -#error I2C_TIMEOUT must be a multiple of WAIT_INT_CHK -#endif - -/* Operations that can be commanded to the controller */ -enum bcm_kona_cmd_t { - BCM_CMD_NOACTION = 0, - BCM_CMD_START, - BCM_CMD_RESTART, - BCM_CMD_STOP, -}; - -/* Internal divider settings for standard mode, fast mode and fast mode plus */ -struct bus_speed_cfg { - uint8_t time_m; /* Number of cycles for setup time */ - uint8_t time_n; /* Number of cycles for hold time */ - uint8_t prescale; /* Prescale divider */ - uint8_t time_p; /* Timing coefficient */ - uint8_t no_div; /* Disable clock divider */ - uint8_t time_div; /* Post-prescale divider */ -}; - -static const struct bus_speed_cfg std_cfg_table[] = { - [IC_SPEED_MODE_STANDARD] = {0x01, 0x01, 0x03, 0x06, 0x00, 0x02}, - [IC_SPEED_MODE_FAST] = {0x05, 0x01, 0x03, 0x05, 0x01, 0x02}, - [IC_SPEED_MODE_FAST_PLUS] = {0x01, 0x01, 0x03, 0x01, 0x01, 0x03}, -}; - -struct bcm_kona_i2c_dev { - void *base; - uint speed; - const struct bus_speed_cfg *std_cfg; -}; - -/* Keep these two defines in sync */ -#define DEF_SPD I2C_SPEED_STANDARD_RATE -#define DEF_SPD_ENUM IC_SPEED_MODE_STANDARD - -#define DEF_DEVICE(num) \ -{(void *)CONFIG_SYS_I2C_BASE##num, DEF_SPD, &std_cfg_table[DEF_SPD_ENUM]} - -static struct bcm_kona_i2c_dev g_i2c_devs[CFG_SYS_MAX_I2C_BUS] = { -#ifdef CONFIG_SYS_I2C_BASE0 - DEF_DEVICE(0), -#endif -#ifdef CONFIG_SYS_I2C_BASE1 - DEF_DEVICE(1), -#endif -#ifdef CONFIG_SYS_I2C_BASE2 - DEF_DEVICE(2), -#endif -#ifdef CONFIG_SYS_I2C_BASE3 - DEF_DEVICE(3), -#endif -#ifdef CONFIG_SYS_I2C_BASE4 - DEF_DEVICE(4), -#endif -#ifdef CONFIG_SYS_I2C_BASE5 - DEF_DEVICE(5), -#endif -}; - -#define I2C_M_TEN 0x0010 /* ten bit address */ -#define I2C_M_RD 0x0001 /* read data */ -#define I2C_M_NOSTART 0x4000 /* no restart between msgs */ - -struct kona_i2c_msg { - uint16_t addr; - uint16_t flags; - uint16_t len; - uint8_t *buf; -}; - -static void bcm_kona_i2c_send_cmd_to_ctrl(struct bcm_kona_i2c_dev *dev, - enum bcm_kona_cmd_t cmd) -{ - debug("%s, %d\n", __func__, cmd); - - switch (cmd) { - case BCM_CMD_NOACTION: - writel((CS_CMD_CMD_NO_ACTION << CS_CMD_SHIFT) | - (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT), - dev->base + CS_OFFSET); - break; - - case BCM_CMD_START: - writel((CS_ACK_CMD_GEN_START << CS_ACK_SHIFT) | - (CS_CMD_CMD_START_RESTART << CS_CMD_SHIFT) | - (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT), - dev->base + CS_OFFSET); - break; - - case BCM_CMD_RESTART: - writel((CS_ACK_CMD_GEN_RESTART << CS_ACK_SHIFT) | - (CS_CMD_CMD_START_RESTART << CS_CMD_SHIFT) | - (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT), - dev->base + CS_OFFSET); - break; - - case BCM_CMD_STOP: - writel((CS_CMD_CMD_STOP << CS_CMD_SHIFT) | - (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT), - dev->base + CS_OFFSET); - break; - - default: - printf("Unknown command %d\n", cmd); - } -} - -static void bcm_kona_i2c_enable_clock(struct bcm_kona_i2c_dev *dev) -{ - writel(readl(dev->base + CLKEN_OFFSET) | CLKEN_CLKEN_MASK, - dev->base + CLKEN_OFFSET); -} - -static void bcm_kona_i2c_disable_clock(struct bcm_kona_i2c_dev *dev) -{ - writel(readl(dev->base + CLKEN_OFFSET) & ~CLKEN_CLKEN_MASK, - dev->base + CLKEN_OFFSET); -} - -/* Wait until at least one of the mask bit(s) are set */ -static unsigned long wait_for_int_timeout(struct bcm_kona_i2c_dev *dev, - unsigned long time_left, - uint32_t mask) -{ - uint32_t status; - - while (time_left) { - status = readl(dev->base + ISR_OFFSET); - - if ((status & ~ISR_RESERVED_MASK) == 0) { - debug("Bogus I2C interrupt 0x%x\n", status); - continue; - } - - /* Must flush the TX FIFO when NAK detected */ - if (status & ISR_NOACK_MASK) - writel(TXFCR_FIFO_FLUSH_MASK | TXFCR_FIFO_EN_MASK, - dev->base + TXFCR_OFFSET); - - writel(status & ~ISR_RESERVED_MASK, dev->base + ISR_OFFSET); - - if (status & mask) { - /* We are done since one of the mask bits are set */ - return time_left; - } - udelay(WAIT_INT_CHK); - time_left -= WAIT_INT_CHK; - } - return 0; -} - -/* Send command to I2C bus */ -static int bcm_kona_send_i2c_cmd(struct bcm_kona_i2c_dev *dev, - enum bcm_kona_cmd_t cmd) -{ - int rc = 0; - unsigned long time_left = I2C_TIMEOUT; - - /* Send the command */ - bcm_kona_i2c_send_cmd_to_ctrl(dev, cmd); - - /* Wait for transaction to finish or timeout */ - time_left = wait_for_int_timeout(dev, time_left, IER_I2C_INT_EN_MASK); - - if (!time_left) { - printf("controller timed out\n"); - rc = -ETIMEDOUT; - } - - /* Clear command */ - bcm_kona_i2c_send_cmd_to_ctrl(dev, BCM_CMD_NOACTION); - - return rc; -} - -/* Read a single RX FIFO worth of data from the i2c bus */ -static int bcm_kona_i2c_read_fifo_single(struct bcm_kona_i2c_dev *dev, - uint8_t *buf, unsigned int len, - unsigned int last_byte_nak) -{ - unsigned long time_left = I2C_TIMEOUT; - - /* Start the RX FIFO */ - writel((last_byte_nak << RXFCR_NACK_EN_SHIFT) | - (len << RXFCR_READ_COUNT_SHIFT), dev->base + RXFCR_OFFSET); - - /* Wait for FIFO read to complete */ - time_left = - wait_for_int_timeout(dev, time_left, IER_READ_COMPLETE_INT_MASK); - - if (!time_left) { - printf("RX FIFO time out\n"); - return -EREMOTEIO; - } - - /* Read data from FIFO */ - for (; len > 0; len--, buf++) - *buf = readl(dev->base + RXFIFORDOUT_OFFSET); - - return 0; -} - -/* Read any amount of data using the RX FIFO from the i2c bus */ -static int bcm_kona_i2c_read_fifo(struct bcm_kona_i2c_dev *dev, - struct kona_i2c_msg *msg) -{ - unsigned int bytes_to_read = MAX_RX_FIFO_SIZE; - unsigned int last_byte_nak = 0; - unsigned int bytes_read = 0; - int rc; - - uint8_t *tmp_buf = msg->buf; - - while (bytes_read < msg->len) { - if (msg->len - bytes_read <= MAX_RX_FIFO_SIZE) { - last_byte_nak = 1; /* NAK last byte of transfer */ - bytes_to_read = msg->len - bytes_read; - } - - rc = bcm_kona_i2c_read_fifo_single(dev, tmp_buf, bytes_to_read, - last_byte_nak); - if (rc < 0) - return -EREMOTEIO; - - bytes_read += bytes_to_read; - tmp_buf += bytes_to_read; - } - - return 0; -} - -/* Write a single byte of data to the i2c bus */ -static int bcm_kona_i2c_write_byte(struct bcm_kona_i2c_dev *dev, uint8_t data, - unsigned int nak_expected) -{ - unsigned long time_left = I2C_TIMEOUT; - unsigned int nak_received; - - /* Clear pending session done interrupt */ - writel(ISR_SES_DONE_MASK, dev->base + ISR_OFFSET); - - /* Send one byte of data */ - writel(data, dev->base + DAT_OFFSET); - - time_left = wait_for_int_timeout(dev, time_left, IER_I2C_INT_EN_MASK); - - if (!time_left) { - debug("controller timed out\n"); - return -ETIMEDOUT; - } - - nak_received = readl(dev->base + CS_OFFSET) & CS_ACK_MASK ? 1 : 0; - - if (nak_received ^ nak_expected) { - debug("unexpected NAK/ACK\n"); - return -EREMOTEIO; - } - - return 0; -} - -/* Write a single TX FIFO worth of data to the i2c bus */ -static int bcm_kona_i2c_write_fifo_single(struct bcm_kona_i2c_dev *dev, - uint8_t *buf, unsigned int len) -{ - int k; - unsigned long time_left = I2C_TIMEOUT; - unsigned int fifo_status; - - /* Write data into FIFO */ - for (k = 0; k < len; k++) - writel(buf[k], (dev->base + DAT_OFFSET)); - - /* Wait for FIFO to empty */ - do { - time_left = - wait_for_int_timeout(dev, time_left, - (IER_FIFO_INT_EN_MASK | - IER_NOACK_EN_MASK)); - fifo_status = readl(dev->base + FIFO_STATUS_OFFSET); - } while (time_left && !(fifo_status & FIFO_STATUS_TXFIFO_EMPTY_MASK)); - - /* Check if there was a NAK */ - if (readl(dev->base + CS_OFFSET) & CS_ACK_MASK) { - printf("unexpected NAK\n"); - return -EREMOTEIO; - } - - /* Check if a timeout occurred */ - if (!time_left) { - printf("completion timed out\n"); - return -EREMOTEIO; - } - - return 0; -} - -/* Write any amount of data using TX FIFO to the i2c bus */ -static int bcm_kona_i2c_write_fifo(struct bcm_kona_i2c_dev *dev, - struct kona_i2c_msg *msg) -{ - unsigned int bytes_to_write = MAX_TX_FIFO_SIZE; - unsigned int bytes_written = 0; - int rc; - - uint8_t *tmp_buf = msg->buf; - - while (bytes_written < msg->len) { - if (msg->len - bytes_written <= MAX_TX_FIFO_SIZE) - bytes_to_write = msg->len - bytes_written; - - rc = bcm_kona_i2c_write_fifo_single(dev, tmp_buf, - bytes_to_write); - if (rc < 0) - return -EREMOTEIO; - - bytes_written += bytes_to_write; - tmp_buf += bytes_to_write; - } - - return 0; -} - -/* Send i2c address */ -static int bcm_kona_i2c_do_addr(struct bcm_kona_i2c_dev *dev, - struct kona_i2c_msg *msg) -{ - unsigned char addr; - - if (msg->flags & I2C_M_TEN) { - /* First byte is 11110XX0 where XX is upper 2 bits */ - addr = 0xf0 | ((msg->addr & 0x300) >> 7); - if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0) - return -EREMOTEIO; - - /* Second byte is the remaining 8 bits */ - addr = msg->addr & 0xff; - if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0) - return -EREMOTEIO; - - if (msg->flags & I2C_M_RD) { - /* For read, send restart command */ - if (bcm_kona_send_i2c_cmd(dev, BCM_CMD_RESTART) < 0) - return -EREMOTEIO; - - /* Then re-send the first byte with the read bit set */ - addr = 0xf0 | ((msg->addr & 0x300) >> 7) | 0x01; - if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0) - return -EREMOTEIO; - } - } else { - addr = msg->addr << 1; - - if (msg->flags & I2C_M_RD) - addr |= 1; - - if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0) - return -EREMOTEIO; - } - - return 0; -} - -static void bcm_kona_i2c_enable_autosense(struct bcm_kona_i2c_dev *dev) -{ - writel(readl(dev->base + CLKEN_OFFSET) & ~CLKEN_AUTOSENSE_OFF_MASK, - dev->base + CLKEN_OFFSET); -} - -static void bcm_kona_i2c_config_timing(struct bcm_kona_i2c_dev *dev) -{ - writel(readl(dev->base + HSTIM_OFFSET) & ~HSTIM_HS_MODE_MASK, - dev->base + HSTIM_OFFSET); - - writel((dev->std_cfg->prescale << TIM_PRESCALE_SHIFT) | - (dev->std_cfg->time_p << TIM_P_SHIFT) | - (dev->std_cfg->no_div << TIM_NO_DIV_SHIFT) | - (dev->std_cfg->time_div << TIM_DIV_SHIFT), - dev->base + TIM_OFFSET); - - writel((dev->std_cfg->time_m << CLKEN_M_SHIFT) | - (dev->std_cfg->time_n << CLKEN_N_SHIFT) | - CLKEN_CLKEN_MASK, dev->base + CLKEN_OFFSET); -} - -/* Master transfer function */ -static int bcm_kona_i2c_xfer(struct bcm_kona_i2c_dev *dev, - struct kona_i2c_msg msgs[], int num) -{ - struct kona_i2c_msg *pmsg; - int rc = 0; - int i; - - /* Enable pad output */ - writel(0, dev->base + PADCTL_OFFSET); - - /* Enable internal clocks */ - bcm_kona_i2c_enable_clock(dev); - - /* Send start command */ - rc = bcm_kona_send_i2c_cmd(dev, BCM_CMD_START); - if (rc < 0) { - printf("Start command failed rc = %d\n", rc); - goto xfer_disable_pad; - } - - /* Loop through all messages */ - for (i = 0; i < num; i++) { - pmsg = &msgs[i]; - - /* Send restart for subsequent messages */ - if ((i != 0) && ((pmsg->flags & I2C_M_NOSTART) == 0)) { - rc = bcm_kona_send_i2c_cmd(dev, BCM_CMD_RESTART); - if (rc < 0) { - printf("restart cmd failed rc = %d\n", rc); - goto xfer_send_stop; - } - } - - /* Send slave address */ - if (!(pmsg->flags & I2C_M_NOSTART)) { - rc = bcm_kona_i2c_do_addr(dev, pmsg); - if (rc < 0) { - debug("NAK from addr %2.2x msg#%d rc = %d\n", - pmsg->addr, i, rc); - goto xfer_send_stop; - } - } - - /* Perform data transfer */ - if (pmsg->flags & I2C_M_RD) { - rc = bcm_kona_i2c_read_fifo(dev, pmsg); - if (rc < 0) { - printf("read failure\n"); - goto xfer_send_stop; - } - } else { - rc = bcm_kona_i2c_write_fifo(dev, pmsg); - if (rc < 0) { - printf("write failure"); - goto xfer_send_stop; - } - } - } - - rc = num; - -xfer_send_stop: - /* Send a STOP command */ - bcm_kona_send_i2c_cmd(dev, BCM_CMD_STOP); - -xfer_disable_pad: - /* Disable pad output */ - writel(PADCTL_PAD_OUT_EN_MASK, dev->base + PADCTL_OFFSET); - - /* Stop internal clock */ - bcm_kona_i2c_disable_clock(dev); - - return rc; -} - -static uint bcm_kona_i2c_assign_bus_speed(struct bcm_kona_i2c_dev *dev, - uint speed) -{ - switch (speed) { - case I2C_SPEED_STANDARD_RATE: - dev->std_cfg = &std_cfg_table[IC_SPEED_MODE_STANDARD]; - break; - case I2C_SPEED_FAST_RATE: - dev->std_cfg = &std_cfg_table[IC_SPEED_MODE_FAST]; - break; - case I2C_SPEED_FAST_PLUS_RATE: - dev->std_cfg = &std_cfg_table[IC_SPEED_MODE_FAST_PLUS]; - break; - default: - printf("%d hz bus speed not supported\n", speed); - return -EINVAL; - } - dev->speed = speed; - return 0; -} - -static void bcm_kona_i2c_init(struct bcm_kona_i2c_dev *dev) -{ - /* Parse bus speed */ - bcm_kona_i2c_assign_bus_speed(dev, dev->speed); - - /* Enable internal clocks */ - bcm_kona_i2c_enable_clock(dev); - - /* Configure internal dividers */ - bcm_kona_i2c_config_timing(dev); - - /* Disable timeout */ - writel(0, dev->base + TOUT_OFFSET); - - /* Enable autosense */ - bcm_kona_i2c_enable_autosense(dev); - - /* Enable TX FIFO */ - writel(TXFCR_FIFO_FLUSH_MASK | TXFCR_FIFO_EN_MASK, - dev->base + TXFCR_OFFSET); - - /* Mask all interrupts */ - writel(0, dev->base + IER_OFFSET); - - /* Clear all pending interrupts */ - writel(ISR_CMDBUSY_MASK | - ISR_READ_COMPLETE_MASK | - ISR_SES_DONE_MASK | - ISR_ERR_MASK | - ISR_TXFIFOEMPTY_MASK | ISR_NOACK_MASK, dev->base + ISR_OFFSET); - - /* Enable the controller but leave it idle */ - bcm_kona_i2c_send_cmd_to_ctrl(dev, BCM_CMD_NOACTION); - - /* Disable pad output */ - writel(PADCTL_PAD_OUT_EN_MASK, dev->base + PADCTL_OFFSET); -} - -/* - * uboot layer - */ -struct bcm_kona_i2c_dev *kona_get_dev(struct i2c_adapter *adap) -{ - return &g_i2c_devs[adap->hwadapnr]; -} - -static void kona_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr) -{ - struct bcm_kona_i2c_dev *dev = kona_get_dev(adap); - - if (clk_bsc_enable(dev->base)) - return; - - bcm_kona_i2c_init(dev); -} - -static int kona_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr, - int alen, uchar *buffer, int len) -{ - /* msg[0] writes the addr, msg[1] reads the data */ - struct kona_i2c_msg msg[2]; - unsigned char msgbuf0[64]; - struct bcm_kona_i2c_dev *dev = kona_get_dev(adap); - - msg[0].addr = chip; - msg[0].flags = 0; - msg[0].len = 1; - msg[0].buf = msgbuf0; /* msgbuf0 contains incrementing reg addr */ - - msg[1].addr = chip; - msg[1].flags = I2C_M_RD; - /* msg[1].buf dest ptr increments each read */ - - msgbuf0[0] = (unsigned char)addr; - msg[1].buf = buffer; - msg[1].len = len; - if (bcm_kona_i2c_xfer(dev, msg, 2) < 0) { - /* Sending 2 i2c messages */ - kona_i2c_init(adap, adap->speed, adap->slaveaddr); - debug("I2C read: I/O error\n"); - return -EIO; - } - return 0; -} - -static int kona_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr, - int alen, uchar *buffer, int len) -{ - struct kona_i2c_msg msg[1]; - unsigned char msgbuf0[64]; - unsigned int i; - struct bcm_kona_i2c_dev *dev = kona_get_dev(adap); - - msg[0].addr = chip; - msg[0].flags = 0; - msg[0].len = 2; /* addr byte plus data */ - msg[0].buf = msgbuf0; - - for (i = 0; i < len; i++) { - msgbuf0[0] = addr++; - msgbuf0[1] = buffer[i]; - if (bcm_kona_i2c_xfer(dev, msg, 1) < 0) { - kona_i2c_init(adap, adap->speed, adap->slaveaddr); - debug("I2C write: I/O error\n"); - return -EIO; - } - } - return 0; -} - -static int kona_i2c_probe(struct i2c_adapter *adap, uchar chip) -{ - uchar tmp; - - /* - * read addr 0x0 of the given chip. - */ - return kona_i2c_read(adap, chip, 0x0, 1, &tmp, 1); -} - -static uint kona_i2c_set_bus_speed(struct i2c_adapter *adap, uint speed) -{ - struct bcm_kona_i2c_dev *dev = kona_get_dev(adap); - return bcm_kona_i2c_assign_bus_speed(dev, speed); -} - -/* - * Register kona i2c adapters. Keep the order below so - * that the bus number matches the adapter number. - */ -#define DEF_ADAPTER(num) \ -U_BOOT_I2C_ADAP_COMPLETE(kona##num, kona_i2c_init, kona_i2c_probe, \ - kona_i2c_read, kona_i2c_write, \ - kona_i2c_set_bus_speed, DEF_SPD, 0x00, num) - -#ifdef CONFIG_SYS_I2C_BASE0 - DEF_ADAPTER(0) -#endif -#ifdef CONFIG_SYS_I2C_BASE1 - DEF_ADAPTER(1) -#endif -#ifdef CONFIG_SYS_I2C_BASE2 - DEF_ADAPTER(2) -#endif -#ifdef CONFIG_SYS_I2C_BASE3 - DEF_ADAPTER(3) -#endif -#ifdef CONFIG_SYS_I2C_BASE4 - DEF_ADAPTER(4) -#endif -#ifdef CONFIG_SYS_I2C_BASE5 - DEF_ADAPTER(5) -#endif -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 62/76] compulab: Drop CONFIG_TARGET_MCM_IMX8M_MINI 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (58 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 61/76] sh4: Drop unused kona_i2c driver Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 63/76] freescale: Drop CONFIG_TARGET_MPC8536DS et al Simon Glass ` (12 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This option is not defined anywhere. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) board/compulab/imx8mm-cl-iot-gate/ddr/Makefile | 4 ---- 1 file changed, 4 deletions(-) diff --git a/board/compulab/imx8mm-cl-iot-gate/ddr/Makefile b/board/compulab/imx8mm-cl-iot-gate/ddr/Makefile index 5914796628d..f73f35cd664 100644 --- a/board/compulab/imx8mm-cl-iot-gate/ddr/Makefile +++ b/board/compulab/imx8mm-cl-iot-gate/ddr/Makefile @@ -1,8 +1,4 @@ obj-y += ddr.o obj-y += lpddr4_timing_ff020008.o obj-y += lpddr4_timing_ff000110.o -ifdef CONFIG_TARGET_MCM_IMX8M_MINI -obj-y += lpddr4_timing_01061010.o -else obj-y += lpddr4_timing_01061010.1_2.o -endif -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 63/76] freescale: Drop CONFIG_TARGET_MPC8536DS et al 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (59 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 62/76] compulab: Drop CONFIG_TARGET_MCM_IMX8M_MINI Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 65/76] ppc: Makefile: Drop unused ppc4xx code Simon Glass ` (11 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This option as well as CONFIG_TARGET_P1022DS and CONFIG_TARGET_P5020DS are not defined anywhere. Drop them. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) board/freescale/common/Makefile | 3 --- 1 file changed, 3 deletions(-) diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index bd035d60a58..5f0503faf8d 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -51,8 +51,6 @@ endif obj-$(CONFIG_TARGET_MPC8548CDS) += cds_pci_ft.o -obj-$(CONFIG_TARGET_MPC8536DS) += ics307_clk.o -obj-$(CONFIG_TARGET_P1022DS) += ics307_clk.o obj-$(CONFIG_TARGET_P3041DS) += ics307_clk.o obj-$(CONFIG_TARGET_P4080DS) += ics307_clk.o obj-$(CONFIG_TARGET_P5040DS) += ics307_clk.o @@ -75,7 +73,6 @@ obj-$(CONFIG_EMC2305) += emc2305.o obj-$(CONFIG_TARGET_P2041RDB) += p_corenet/ obj-$(CONFIG_TARGET_P3041DS) += p_corenet/ obj-$(CONFIG_TARGET_P4080DS) += p_corenet/ -obj-$(CONFIG_TARGET_P5020DS) += p_corenet/ obj-$(CONFIG_TARGET_P5040DS) += p_corenet/ obj-$(CONFIG_LAYERSCAPE_NS_ACCESS) += ns_access.o -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 65/76] ppc: Makefile: Drop unused ppc4xx code 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (60 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 63/76] freescale: Drop CONFIG_TARGET_MPC8536DS et al Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 66/76] armada: usb: net: Drop unused USB drivers Simon Glass ` (10 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot Cc: Tom Rini, Simon Glass, Stefan Roese, Andy Fleming, Mario Six, Priyanka Jain, Wolfgang Denk CONFIG_UBOOT_PAD_TO is not defined anywhere. Drop this dead code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> --- (no changes since v1) Makefile | 11 ----------- 1 file changed, 11 deletions(-) diff --git a/Makefile b/Makefile index 2c9e27ac5c2..815ee0333d8 100644 --- a/Makefile +++ b/Makefile @@ -1648,17 +1648,6 @@ OBJCOPYFLAGS_u-boot-with-spl-pbl.bin = -I binary -O binary --pad-to=$(CONFIG_SPL u-boot-with-spl-pbl.bin: spl/u-boot-spl.pbl $(UBOOT_BINLOAD) FORCE $(call if_changed,pad_cat) -# PPC4xx needs the SPL at the end of the image, since the reset vector -# is located at 0xfffffffc. So we can't use the "u-boot-img.bin" target -# and need to introduce a new build target with the full blown U-Boot -# at the start padded up to the start of the SPL image. And then concat -# the SPL image to the end. - -OBJCOPYFLAGS_u-boot-img-spl-at-end.bin := -I binary -O binary \ - --pad-to=$(CONFIG_UBOOT_PAD_TO) --gap-fill=0xff -u-boot-img-spl-at-end.bin: u-boot.img spl/u-boot-spl.bin FORCE - $(call if_changed,pad_cat) - quiet_cmd_u-boot-elf ?= LD $@ cmd_u-boot-elf ?= $(LD) u-boot-elf.o -o $@ \ $(if $(CONFIG_SYS_BIG_ENDIAN),-EB,-EL) \ -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 66/76] armada: usb: net: Drop unused USB drivers 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (61 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 65/76] ppc: Makefile: Drop unused ppc4xx code Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 67/76] usb: Drop unused ehci-faraday driver Simon Glass ` (9 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Joe Hershberger, Marek Vasut These are not used. Drop the drivers and Kconfig option. Also drop an old declaration in the netdev.h header. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/usb/host/Makefile | 1 - drivers/usb/host/ehci-armada100.c | 48 ------------------- drivers/usb/host/utmi-armada100.c | 80 ------------------------------- include/netdev.h | 1 - 4 files changed, 130 deletions(-) delete mode 100644 drivers/usb/host/ehci-armada100.c delete mode 100644 drivers/usb/host/utmi-armada100.c diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index ddc36632069..1f59e910d3b 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -25,7 +25,6 @@ obj-$(CONFIG_USB_OHCI_NPCM) += ohci-npcm.o # echi obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o -obj-$(CONFIG_USB_EHCI_ARMADA100) += ehci-armada100.o utmi-armada100.o obj-$(CONFIG_USB_EHCI_ATMEL) += ehci-atmel.o obj-$(CONFIG_USB_EHCI_FSL) += ehci-fsl.o obj-$(CONFIG_USB_EHCI_FARADAY) += ehci-faraday.o diff --git a/drivers/usb/host/ehci-armada100.c b/drivers/usb/host/ehci-armada100.c deleted file mode 100644 index 2ce9f27b862..00000000000 --- a/drivers/usb/host/ehci-armada100.c +++ /dev/null @@ -1,48 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2012 - * eInfochips Ltd. <www.einfochips.com> - * Written-by: Ajay Bhargav <contact@8051projects.net> - * - * This driver is based on Kirkwood echi driver - * (C) Copyright 2009 - * Marvell Semiconductor <www.marvell.com> - * Written-by: Prafulla Wadaskar <prafulla@marvell.com> - */ - -#include <common.h> -#include <log.h> -#include <asm/io.h> -#include <usb.h> -#include "ehci.h" -#include <asm/arch/cpu.h> -#include <asm/arch/armada100.h> -#include <asm/arch/utmi-armada100.h> - -/* - * EHCI host controller init - */ -int ehci_hcd_init(int index, enum usb_init_type init, - struct ehci_hccr **hccr, struct ehci_hcor **hcor) -{ - if (utmi_init() < 0) - return -1; - - *hccr = (struct ehci_hccr *)(ARMD1_USB_HOST_BASE + 0x100); - *hcor = (struct ehci_hcor *)((uint32_t) *hccr - + HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase))); - - debug("armada100-ehci: init hccr %x and hcor %x hc_length %d\n", - (uint32_t)*hccr, (uint32_t)*hcor, - (uint32_t)HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase))); - - return 0; -} - -/* - * EHCI host controller stop - */ -int ehci_hcd_stop(int index) -{ - return 0; -} diff --git a/drivers/usb/host/utmi-armada100.c b/drivers/usb/host/utmi-armada100.c deleted file mode 100644 index 5d66e5881f3..00000000000 --- a/drivers/usb/host/utmi-armada100.c +++ /dev/null @@ -1,80 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2012 - * eInfochips Ltd. <www.einfochips.com> - * Written-by: Ajay Bhargav <contact@8051projects.net> - * - * (C) Copyright 2009 - * Marvell Semiconductor <www.marvell.com> - */ - -#include <common.h> -#include <asm/io.h> -#include <usb.h> -#include <asm/arch/cpu.h> -#include <asm/arch/armada100.h> -#include <asm/arch/utmi-armada100.h> -#include <linux/delay.h> - -static int utmi_phy_init(void) -{ - struct armd1usb_phy_reg *phy_regs = - (struct armd1usb_phy_reg *)UTMI_PHY_BASE; - int timeout; - - setbits_le32(&phy_regs->utmi_ctrl, INPKT_DELAY_SOF | PLL_PWR_UP); - udelay(1000); - setbits_le32(&phy_regs->utmi_ctrl, PHY_PWR_UP); - - clrbits_le32(&phy_regs->utmi_pll, PLL_FBDIV_MASK | PLL_REFDIV_MASK); - setbits_le32(&phy_regs->utmi_pll, N_DIVIDER << PLL_FBDIV | M_DIVIDER); - - setbits_le32(&phy_regs->utmi_tx, PHSEL_VAL << CK60_PHSEL); - - /* Calibrate pll */ - timeout = 10000; - while (--timeout && ((readl(&phy_regs->utmi_pll) & PLL_READY) == 0)) - ; - if (!timeout) - return -1; - - udelay(200); - setbits_le32(&phy_regs->utmi_pll, VCOCAL_START); - udelay(400); - clrbits_le32(&phy_regs->utmi_pll, VCOCAL_START); - - udelay(200); - setbits_le32(&phy_regs->utmi_tx, RCAL_START); - udelay(400); - clrbits_le32(&phy_regs->utmi_tx, RCAL_START); - - timeout = 10000; - while (--timeout && ((readl(&phy_regs->utmi_pll) & PLL_READY) == 0)) - ; - if (!timeout) - return -1; - - return 0; -} - -/* - * Initialize USB host controller's UTMI Physical interface - */ -int utmi_init(void) -{ - struct armd1mpmu_registers *mpmu_regs = - (struct armd1mpmu_registers *)ARMD1_MPMU_BASE; - - struct armd1apmu_registers *apmu_regs = - (struct armd1apmu_registers *)ARMD1_APMU_BASE; - - /* Turn on 26Mhz ref clock for UTMI PLL */ - setbits_le32(&mpmu_regs->acgr, APB2_26M_EN | AP_26M); - - /* USB Clock reset */ - writel(USB_SPH_AXICLK_EN, &apmu_regs->usbcrc); - writel(USB_SPH_AXICLK_EN | USB_SPH_AXI_RST, &apmu_regs->usbcrc); - - /* Initialize UTMI transceiver */ - return utmi_phy_init(); -} diff --git a/include/netdev.h b/include/netdev.h index 2b4e474ed08..2a7f40e5040 100644 --- a/include/netdev.h +++ b/include/netdev.h @@ -71,7 +71,6 @@ int skge_initialize(struct bd_info *bis); int smc91111_initialize(u8 dev_num, phys_addr_t base_addr); int smc911x_initialize(u8 dev_num, phys_addr_t base_addr); int uli526x_initialize(struct bd_info *bis); -int armada100_fec_register(unsigned long base_addr); /* Boards with PCI network controllers can call this from their board_eth_init() * function to initialize whatever's on board. -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 67/76] usb: Drop unused ehci-faraday driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (62 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 66/76] armada: usb: net: Drop unused USB drivers Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 68/76] usb: Drop unused fotg210 gadget Simon Glass ` (8 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Marek Vasut This is not used. Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v2) Changes in v2: - Reinstate usb_hub code removed by accident common/usb_hub.c | 6 -- drivers/usb/host/Makefile | 1 - drivers/usb/host/ehci-faraday.c | 144 -------------------------------- drivers/usb/host/ehci-hcd.c | 5 -- include/usb/fusbh200.h | 59 ------------- 5 files changed, 215 deletions(-) delete mode 100644 drivers/usb/host/ehci-faraday.c delete mode 100644 include/usb/fusbh200.h diff --git a/common/usb_hub.c b/common/usb_hub.c index f7fd12c0450..85c0822d8b7 100644 --- a/common/usb_hub.c +++ b/common/usb_hub.c @@ -506,11 +506,6 @@ static int usb_scan_port(struct usb_device_scan *usb_scan) if (portchange & USB_PORT_STAT_C_ENABLE) { debug("port %d enable change, status %x\n", i + 1, portstatus); usb_clear_port_feature(dev, i + 1, USB_PORT_FEAT_C_ENABLE); - /* - * The following hack causes a ghost device problem - * to Faraday EHCI - */ -#ifndef CONFIG_USB_EHCI_FARADAY /* * EM interference sometimes causes bad shielded USB * devices to be shutdown by the hub, this hack enables @@ -523,7 +518,6 @@ static int usb_scan_port(struct usb_device_scan *usb_scan) i + 1); usb_hub_port_connect_change(dev, i); } -#endif } if (portstatus & USB_PORT_STAT_SUSPEND) { diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 1f59e910d3b..cce78846d98 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -27,7 +27,6 @@ obj-$(CONFIG_USB_OHCI_NPCM) += ohci-npcm.o obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o obj-$(CONFIG_USB_EHCI_ATMEL) += ehci-atmel.o obj-$(CONFIG_USB_EHCI_FSL) += ehci-fsl.o -obj-$(CONFIG_USB_EHCI_FARADAY) += ehci-faraday.o obj-$(CONFIG_USB_EHCI_GENERIC) += ehci-generic.o obj-$(CONFIG_USB_EHCI_EXYNOS) += ehci-exynos.o obj-$(CONFIG_USB_EHCI_MXS) += ehci-mxs.o diff --git a/drivers/usb/host/ehci-faraday.c b/drivers/usb/host/ehci-faraday.c deleted file mode 100644 index 85a35269601..00000000000 --- a/drivers/usb/host/ehci-faraday.c +++ /dev/null @@ -1,144 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Faraday USB 2.0 EHCI Controller - * - * (C) Copyright 2010 Faraday Technology - * Dante Su <dantesu@faraday-tech.com> - */ - -#include <common.h> -#include <log.h> -#include <asm/io.h> -#include <usb.h> -#include <linux/delay.h> -#include <usb/fusbh200.h> -#include <usb/fotg210.h> - -#include "ehci.h" - -#ifndef CFG_USB_EHCI_BASE_LIST -#define CFG_USB_EHCI_BASE_LIST { CONFIG_USB_EHCI_BASE } -#endif - -union ehci_faraday_regs { - struct fusbh200_regs usb; - struct fotg210_regs otg; -}; - -static inline int ehci_is_fotg2xx(union ehci_faraday_regs *regs) -{ - return !readl(®s->usb.easstr); -} - -void faraday_ehci_set_usbmode(struct ehci_ctrl *ctrl) -{ - /* nothing needs to be done */ -} - -int faraday_ehci_get_port_speed(struct ehci_ctrl *ctrl, uint32_t reg) -{ - int spd, ret = PORTSC_PSPD_HS; - union ehci_faraday_regs *regs; - - ret = (void __iomem *)((ulong)ctrl->hcor - 0x10); - if (ehci_is_fotg2xx(regs)) - spd = OTGCSR_SPD(readl(®s->otg.otgcsr)); - else - spd = BMCSR_SPD(readl(®s->usb.bmcsr)); - - switch (spd) { - case 0: /* full speed */ - ret = PORTSC_PSPD_FS; - break; - case 1: /* low speed */ - ret = PORTSC_PSPD_LS; - break; - case 2: /* high speed */ - ret = PORTSC_PSPD_HS; - break; - default: - printf("ehci-faraday: invalid device speed\n"); - break; - } - - return ret; -} - -uint32_t *faraday_ehci_get_portsc_register(struct ehci_ctrl *ctrl, int port) -{ - /* Faraday EHCI has one and only one portsc register */ - if (port) { - /* Printing the message would cause a scan failure! */ - debug("The request port(%d) is not configured\n", port); - return NULL; - } - - /* Faraday EHCI PORTSC register offset is 0x20 from hcor */ - return (uint32_t *)((uint8_t *)ctrl->hcor + 0x20); -} - -static const struct ehci_ops faraday_ehci_ops = { - .set_usb_mode = faraday_ehci_set_usbmode, - .get_port_speed = faraday_ehci_get_port_speed, - .get_portsc_register = faraday_ehci_get_portsc_register, -}; - -/* - * Create the appropriate control structures to manage - * a new EHCI host controller. - */ -int ehci_hcd_init(int index, enum usb_init_type init, - struct ehci_hccr **ret_hccr, struct ehci_hcor **ret_hcor) -{ - struct ehci_hccr *hccr; - struct ehci_hcor *hcor; - union ehci_faraday_regs *regs; - uint32_t base_list[] = CFG_USB_EHCI_BASE_LIST; - - if (index < 0 || index >= ARRAY_SIZE(base_list)) - return -1; - ehci_set_controller_priv(index, NULL, &faraday_ehci_ops); - regs = (void __iomem *)base_list[index]; - hccr = (struct ehci_hccr *)®s->usb.hccr; - hcor = (struct ehci_hcor *)®s->usb.hcor; - - if (ehci_is_fotg2xx(regs)) { - /* A-device bus reset */ - /* ... Power off A-device */ - setbits_le32(®s->otg.otgcsr, OTGCSR_A_BUSDROP); - /* ... Drop vbus and bus traffic */ - clrbits_le32(®s->otg.otgcsr, OTGCSR_A_BUSREQ); - mdelay(1); - /* ... Power on A-device */ - clrbits_le32(®s->otg.otgcsr, OTGCSR_A_BUSDROP); - /* ... Drive vbus and bus traffic */ - setbits_le32(®s->otg.otgcsr, OTGCSR_A_BUSREQ); - mdelay(1); - /* Disable OTG & DEV interrupts, triggered at level-high */ - writel(IMR_IRQLH | IMR_OTG | IMR_DEV, ®s->otg.imr); - /* Clear all interrupt status */ - writel(ISR_HOST | ISR_OTG | ISR_DEV, ®s->otg.isr); - } else { - /* Interrupt=level-high */ - setbits_le32(®s->usb.bmcsr, BMCSR_IRQLH); - /* VBUS on */ - clrbits_le32(®s->usb.bmcsr, BMCSR_VBUS_OFF); - /* Disable all interrupts */ - writel(0x00, ®s->usb.bmier); - writel(0x1f, ®s->usb.bmisr); - } - - *ret_hccr = hccr; - *ret_hcor = hcor; - - return 0; -} - -/* - * Destroy the appropriate control structures corresponding - * the the EHCI host controller. - */ -int ehci_hcd_stop(int index) -{ - return 0; -} diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index 9139d61dd0c..9839aa17492 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -705,12 +705,10 @@ ehci_submit_async(struct usb_device *dev, unsigned long pipe, void *buffer, dev->act_len = length - QT_TOKEN_GET_TOTALBYTES(qhtoken); } else { dev->act_len = 0; -#ifndef CONFIG_USB_EHCI_FARADAY debug("dev=%u, usbsts=%#x, p[1]=%#x, p[2]=%#x\n", dev->devnum, ehci_readl(&ctrl->hcor->or_usbsts), ehci_readl(&ctrl->hcor->or_portsc[0]), ehci_readl(&ctrl->hcor->or_portsc[1])); -#endif } free(qtd); @@ -1189,9 +1187,6 @@ int usb_lowlevel_init(int index, enum usb_init_type init, void **controller) rc = ehci_hcd_init(index, init, &ctrl->hccr, &ctrl->hcor); if (rc) return rc; -#endif -#ifdef CONFIG_USB_EHCI_FARADAY - tweaks |= EHCI_TWEAK_NO_INIT_CF; #endif rc = ehci_common_init(ctrl, tweaks); if (rc) diff --git a/include/usb/fusbh200.h b/include/usb/fusbh200.h deleted file mode 100644 index 6ae1d848801..00000000000 --- a/include/usb/fusbh200.h +++ /dev/null @@ -1,59 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Faraday USB 2.0 EHCI Controller - * - * (C) Copyright 2010 Faraday Technology - * Dante Su <dantesu@faraday-tech.com> - */ - -#ifndef _FUSBH200_H -#define _FUSBH200_H - -struct fusbh200_regs { - struct { - uint32_t data[4]; - } hccr; /* 0x00 - 0x0f: hccr */ - struct { - uint32_t data[9]; - } hcor; /* 0x10 - 0x33: hcor */ - uint32_t easstr;/* 0x34: EOF&Async. Sched. Sleep Timer Register */ - uint32_t rsvd[2]; - uint32_t bmcsr; /* 0x40: Bus Monitor Control Status Register */ - uint32_t bmisr; /* 0x44: Bus Monitor Interrupt Status Register */ - uint32_t bmier; /* 0x48: Bus Monitor Interrupt Enable Register */ -}; - -/* EOF & Async. Schedule Sleep Timer Register */ -#define EASSTR_RUNNING (1 << 6) /* Put transceiver in running/resume mode */ -#define EASSTR_SUSPEND (0 << 6) /* Put transceiver in suspend mode */ -#define EASSTR_EOF2(x) (((x) & 0x3) << 4) /* EOF 2 Timing */ -#define EASSTR_EOF1(x) (((x) & 0x3) << 2) /* EOF 1 Timing */ -#define EASSTR_ASST(x) (((x) & 0x3) << 0) /* Async. Sched. Sleep Timer */ - -/* Bus Monitor Control Status Register */ -#define BMCSR_SPD_HIGH (2 << 9) /* Speed of the attached device */ -#define BMCSR_SPD_LOW (1 << 9) -#define BMCSR_SPD_FULL (0 << 9) -#define BMCSR_SPD_MASK (3 << 9) -#define BMCSR_SPD_SHIFT 9 -#define BMCSR_SPD(x) ((x >> 9) & 0x03) -#define BMCSR_VBUS (1 << 8) /* VBUS Valid */ -#define BMCSR_VBUS_OFF (1 << 4) /* VBUS Off */ -#define BMCSR_VBUS_ON (0 << 4) /* VBUS On */ -#define BMCSR_IRQLH (1 << 3) /* IRQ triggered at level-high */ -#define BMCSR_IRQLL (0 << 3) /* IRQ triggered at level-low */ -#define BMCSR_HALFSPD (1 << 2) /* Half speed mode for FPGA test */ -#define BMCSR_HFT_LONG (1 << 1) /* HDISCON noise filter = 270 us*/ -#define BMCSR_HFT (0 << 1) /* HDISCON noise filter = 135 us*/ -#define BMCSR_VFT_LONG (1 << 1) /* VBUS noise filter = 472 us*/ -#define BMCSR_VFT (0 << 1) /* VBUS noise filter = 135 us*/ - -/* Bus Monitor Interrupt Status Register */ -/* Bus Monitor Interrupt Enable Register */ -#define BMISR_DMAERR (1 << 4) /* DMA error */ -#define BMISR_DMA (1 << 3) /* DMA complete */ -#define BMISR_DEVRM (1 << 2) /* device removed */ -#define BMISR_OVD (1 << 1) /* over-current detected */ -#define BMISR_VBUSERR (1 << 0) /* VBUS error */ - -#endif -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 68/76] usb: Drop unused fotg210 gadget 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (63 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 67/76] usb: Drop unused ehci-faraday driver Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-10 23:33 ` Samuel Holland 2023-02-01 20:20 ` [PATCH v3 69/76] rmobile: Drop unused ehci-rmobile driver Simon Glass ` (7 subsequent siblings) 72 siblings, 1 reply; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Marek Vasut This is not used and appears to be associated with the faraday board which has been removed. Drop the driver and Kconfig options. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/usb/gadget/Makefile | 3 +- drivers/usb/gadget/fotg210.c | 964 ------------------------------ drivers/usb/gadget/gadget_chips.h | 8 - include/usb/fotg210.h | 362 ----------- 4 files changed, 1 insertion(+), 1336 deletions(-) delete mode 100644 drivers/usb/gadget/fotg210.c delete mode 100644 include/usb/fotg210.h diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile index 9c04403da30..b04b6bcd779 100644 --- a/drivers/usb/gadget/Makefile +++ b/drivers/usb/gadget/Makefile @@ -19,8 +19,7 @@ obj-$(CONFIG_USB_GADGET_ATMEL_USBA) += atmel_usba_udc.o obj-$(CONFIG_USB_GADGET_BCM_UDC_OTG_PHY) += bcm_udc_otg_phy.o obj-$(CONFIG_USB_GADGET_DWC2_OTG) += dwc2_udc_otg.o obj-$(CONFIG_USB_GADGET_DWC2_OTG_PHY) += dwc2_udc_otg_phy.o -obj-$(CONFIG_USB_GADGET_FOTG210) += fotg210.o -obj-$(CONFIG_USB_GADGET_MAX3420) += max3420_udc.o +0obj-$(CONFIG_USB_GADGET_MAX3420) += max3420_udc.o ifndef CONFIG_SPL_BUILD obj-$(CONFIG_USB_GADGET_DOWNLOAD) += g_dnl.o obj-$(CONFIG_USB_FUNCTION_THOR) += f_thor.o diff --git a/drivers/usb/gadget/fotg210.c b/drivers/usb/gadget/fotg210.c deleted file mode 100644 index af43433d88d..00000000000 --- a/drivers/usb/gadget/fotg210.c +++ /dev/null @@ -1,964 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Faraday USB 2.0 OTG Controller - * - * (C) Copyright 2010 Faraday Technology - * Dante Su <dantesu@faraday-tech.com> - */ - -#include <common.h> -#include <command.h> -#include <config.h> -#include <cpu_func.h> -#include <log.h> -#include <net.h> -#include <malloc.h> -#include <asm/io.h> -#include <linux/delay.h> -#include <linux/errno.h> -#include <linux/types.h> -#include <linux/usb/ch9.h> -#include <linux/usb/gadget.h> - -#include <usb/fotg210.h> - -#define CFG_NUM_ENDPOINTS 4 -#define CFG_EP0_MAX_PACKET_SIZE 64 -#define CFG_EPX_MAX_PACKET_SIZE 512 - -#define CFG_CMD_TIMEOUT (CONFIG_SYS_HZ >> 2) /* 250 ms */ - -struct fotg210_chip; - -struct fotg210_ep { - struct usb_ep ep; - - uint maxpacket; - uint id; - uint stopped; - - struct list_head queue; - struct fotg210_chip *chip; - const struct usb_endpoint_descriptor *desc; -}; - -struct fotg210_request { - struct usb_request req; - struct list_head queue; - struct fotg210_ep *ep; -}; - -struct fotg210_chip { - struct usb_gadget gadget; - struct usb_gadget_driver *driver; - struct fotg210_regs *regs; - uint8_t irq; - uint16_t addr; - int pullup; - enum usb_device_state state; - struct fotg210_ep ep[1 + CFG_NUM_ENDPOINTS]; -}; - -static struct usb_endpoint_descriptor ep0_desc = { - .bLength = sizeof(struct usb_endpoint_descriptor), - .bDescriptorType = USB_DT_ENDPOINT, - .bEndpointAddress = USB_DIR_IN, - .bmAttributes = USB_ENDPOINT_XFER_CONTROL, -}; - -static inline int fifo_to_ep(struct fotg210_chip *chip, int id, int in) -{ - return (id < 0) ? 0 : ((id & 0x03) + 1); -} - -static inline int ep_to_fifo(struct fotg210_chip *chip, int id) -{ - return (id <= 0) ? -1 : ((id - 1) & 0x03); -} - -static inline int ep_reset(struct fotg210_chip *chip, uint8_t ep_addr) -{ - int ep = ep_addr & USB_ENDPOINT_NUMBER_MASK; - struct fotg210_regs *regs = chip->regs; - - if (ep_addr & USB_DIR_IN) { - /* reset endpoint */ - setbits_le32(®s->iep[ep - 1], IEP_RESET); - mdelay(1); - clrbits_le32(®s->iep[ep - 1], IEP_RESET); - /* clear endpoint stall */ - clrbits_le32(®s->iep[ep - 1], IEP_STALL); - } else { - /* reset endpoint */ - setbits_le32(®s->oep[ep - 1], OEP_RESET); - mdelay(1); - clrbits_le32(®s->oep[ep - 1], OEP_RESET); - /* clear endpoint stall */ - clrbits_le32(®s->oep[ep - 1], OEP_STALL); - } - - return 0; -} - -static int fotg210_reset(struct fotg210_chip *chip) -{ - struct fotg210_regs *regs = chip->regs; - uint32_t i; - - chip->state = USB_STATE_POWERED; - - /* chip enable */ - writel(DEVCTRL_EN, ®s->dev_ctrl); - - /* device address reset */ - chip->addr = 0; - writel(0, ®s->dev_addr); - - /* set idle counter to 7ms */ - writel(7, ®s->idle); - - /* disable all interrupts */ - writel(IMR_MASK, ®s->imr); - writel(GIMR_MASK, ®s->gimr); - writel(GIMR0_MASK, ®s->gimr0); - writel(GIMR1_MASK, ®s->gimr1); - writel(GIMR2_MASK, ®s->gimr2); - - /* clear interrupts */ - writel(ISR_MASK, ®s->isr); - writel(0, ®s->gisr); - writel(0, ®s->gisr0); - writel(0, ®s->gisr1); - writel(0, ®s->gisr2); - - /* chip reset */ - setbits_le32(®s->dev_ctrl, DEVCTRL_RESET); - mdelay(10); - if (readl(®s->dev_ctrl) & DEVCTRL_RESET) { - printf("fotg210: chip reset failed\n"); - return -1; - } - - /* CX FIFO reset */ - setbits_le32(®s->cxfifo, CXFIFO_CXFIFOCLR); - mdelay(10); - if (readl(®s->cxfifo) & CXFIFO_CXFIFOCLR) { - printf("fotg210: ep0 fifo reset failed\n"); - return -1; - } - - /* create static ep-fifo map (EP1 <-> FIFO0, EP2 <-> FIFO1 ...) */ - writel(EPMAP14_DEFAULT, ®s->epmap14); - writel(EPMAP58_DEFAULT, ®s->epmap58); - writel(FIFOMAP_DEFAULT, ®s->fifomap); - writel(0, ®s->fifocfg); - for (i = 0; i < 8; ++i) { - writel(CFG_EPX_MAX_PACKET_SIZE, ®s->iep[i]); - writel(CFG_EPX_MAX_PACKET_SIZE, ®s->oep[i]); - } - - /* FIFO reset */ - for (i = 0; i < 4; ++i) { - writel(FIFOCSR_RESET, ®s->fifocsr[i]); - mdelay(10); - if (readl(®s->fifocsr[i]) & FIFOCSR_RESET) { - printf("fotg210: fifo%d reset failed\n", i); - return -1; - } - } - - /* enable only device interrupt and triggered at level-high */ - writel(IMR_IRQLH | IMR_HOST | IMR_OTG, ®s->imr); - writel(ISR_MASK, ®s->isr); - /* disable EP0 IN/OUT interrupt */ - writel(GIMR0_CXOUT | GIMR0_CXIN, ®s->gimr0); - /* disable EPX IN+SPK+OUT interrupts */ - writel(GIMR1_MASK, ®s->gimr1); - /* disable wakeup+idle+dma+zlp interrupts */ - writel(GIMR2_WAKEUP | GIMR2_IDLE | GIMR2_DMAERR | GIMR2_DMAFIN - | GIMR2_ZLPRX | GIMR2_ZLPTX, ®s->gimr2); - /* enable all group interrupt */ - writel(0, ®s->gimr); - - /* suspend delay = 3 ms */ - writel(3, ®s->idle); - - /* turn-on device interrupts */ - setbits_le32(®s->dev_ctrl, DEVCTRL_GIRQ_EN); - - return 0; -} - -static inline int fotg210_cxwait(struct fotg210_chip *chip, uint32_t mask) -{ - struct fotg210_regs *regs = chip->regs; - int ret = -1; - ulong ts; - - for (ts = get_timer(0); get_timer(ts) < CFG_CMD_TIMEOUT; ) { - if ((readl(®s->cxfifo) & mask) != mask) - continue; - ret = 0; - break; - } - - if (ret) - printf("fotg210: cx/ep0 timeout\n"); - - return ret; -} - -static int fotg210_dma(struct fotg210_ep *ep, struct fotg210_request *req) -{ - struct fotg210_chip *chip = ep->chip; - struct fotg210_regs *regs = chip->regs; - uint32_t tmp, ts; - uint8_t *buf = req->req.buf + req->req.actual; - uint32_t len = req->req.length - req->req.actual; - int fifo = ep_to_fifo(chip, ep->id); - int ret = -EBUSY; - - /* 1. init dma buffer */ - if (len > ep->maxpacket) - len = ep->maxpacket; - - /* 2. wait for dma ready (hardware) */ - for (ts = get_timer(0); get_timer(ts) < CFG_CMD_TIMEOUT; ) { - if (!(readl(®s->dma_ctrl) & DMACTRL_START)) { - ret = 0; - break; - } - } - if (ret) { - printf("fotg210: dma busy\n"); - req->req.status = ret; - return ret; - } - - /* 3. DMA target setup */ - if (ep->desc->bEndpointAddress & USB_DIR_IN) - flush_dcache_range((ulong)buf, (ulong)buf + len); - else - invalidate_dcache_range((ulong)buf, (ulong)buf + len); - - writel(virt_to_phys(buf), ®s->dma_addr); - - if (ep->desc->bEndpointAddress & USB_DIR_IN) { - if (ep->id == 0) { - /* Wait until cx/ep0 fifo empty */ - fotg210_cxwait(chip, CXFIFO_CXFIFOE); - udelay(1); - writel(DMAFIFO_CX, ®s->dma_fifo); - } else { - /* Wait until epx fifo empty */ - fotg210_cxwait(chip, CXFIFO_FIFOE(fifo)); - writel(DMAFIFO_FIFO(fifo), ®s->dma_fifo); - } - writel(DMACTRL_LEN(len) | DMACTRL_MEM2FIFO, ®s->dma_ctrl); - } else { - uint32_t blen; - - if (ep->id == 0) { - writel(DMAFIFO_CX, ®s->dma_fifo); - do { - blen = CXFIFO_BYTES(readl(®s->cxfifo)); - } while (blen < len); - } else { - writel(DMAFIFO_FIFO(fifo), ®s->dma_fifo); - blen = FIFOCSR_BYTES(readl(®s->fifocsr[fifo])); - } - len = (len < blen) ? len : blen; - writel(DMACTRL_LEN(len) | DMACTRL_FIFO2MEM, ®s->dma_ctrl); - } - - /* 4. DMA start */ - setbits_le32(®s->dma_ctrl, DMACTRL_START); - - /* 5. DMA wait */ - ret = -EBUSY; - for (ts = get_timer(0); get_timer(ts) < CFG_CMD_TIMEOUT; ) { - tmp = readl(®s->gisr2); - /* DMA complete */ - if (tmp & GISR2_DMAFIN) { - ret = 0; - break; - } - /* DMA error */ - if (tmp & GISR2_DMAERR) { - printf("fotg210: dma error\n"); - break; - } - /* resume, suspend, reset */ - if (tmp & (GISR2_RESUME | GISR2_SUSPEND | GISR2_RESET)) { - printf("fotg210: dma reset by host\n"); - break; - } - } - - /* 7. DMA target reset */ - if (ret) - writel(DMACTRL_ABORT | DMACTRL_CLRFF, ®s->dma_ctrl); - - writel(0, ®s->gisr2); - writel(0, ®s->dma_fifo); - - req->req.status = ret; - if (!ret) - req->req.actual += len; - else - printf("fotg210: ep%d dma error(code=%d)\n", ep->id, ret); - - return len; -} - -/* - * result of setup packet - */ -#define CX_IDLE 0 -#define CX_FINISH 1 -#define CX_STALL 2 - -static void fotg210_setup(struct fotg210_chip *chip) -{ - int id, ret = CX_IDLE; - uint32_t tmp[2]; - struct usb_ctrlrequest *req = (struct usb_ctrlrequest *)tmp; - struct fotg210_regs *regs = chip->regs; - - /* - * If this is the first Cx 8 byte command, - * we can now query USB mode (high/full speed; USB 2.0/USB 1.0) - */ - if (chip->state == USB_STATE_POWERED) { - chip->state = USB_STATE_DEFAULT; - if (readl(®s->otgcsr) & OTGCSR_DEV_B) { - /* Mini-B */ - if (readl(®s->dev_ctrl) & DEVCTRL_HS) { - puts("fotg210: HS\n"); - chip->gadget.speed = USB_SPEED_HIGH; - /* SOF mask timer = 1100 ticks */ - writel(SOFMTR_TMR(1100), ®s->sof_mtr); - } else { - puts("fotg210: FS\n"); - chip->gadget.speed = USB_SPEED_FULL; - /* SOF mask timer = 10000 ticks */ - writel(SOFMTR_TMR(10000), ®s->sof_mtr); - } - } else { - printf("fotg210: mini-A?\n"); - } - } - - /* switch data port to ep0 */ - writel(DMAFIFO_CX, ®s->dma_fifo); - /* fetch 8 bytes setup packet */ - tmp[0] = readl(®s->ep0_data); - tmp[1] = readl(®s->ep0_data); - /* release data port */ - writel(0, ®s->dma_fifo); - - if (req->bRequestType & USB_DIR_IN) - ep0_desc.bEndpointAddress = USB_DIR_IN; - else - ep0_desc.bEndpointAddress = USB_DIR_OUT; - - ret = CX_IDLE; - - if ((req->bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD) { - switch (req->bRequest) { - case USB_REQ_SET_CONFIGURATION: - debug("fotg210: set_cfg(%d)\n", req->wValue & 0x00FF); - if (!(req->wValue & 0x00FF)) { - chip->state = USB_STATE_ADDRESS; - writel(chip->addr, ®s->dev_addr); - } else { - chip->state = USB_STATE_CONFIGURED; - writel(chip->addr | DEVADDR_CONF, - ®s->dev_addr); - } - ret = CX_IDLE; - break; - - case USB_REQ_SET_ADDRESS: - debug("fotg210: set_addr(0x%04X)\n", req->wValue); - chip->state = USB_STATE_ADDRESS; - chip->addr = req->wValue & DEVADDR_ADDR_MASK; - ret = CX_FINISH; - writel(chip->addr, ®s->dev_addr); - break; - - case USB_REQ_CLEAR_FEATURE: - debug("fotg210: clr_feature(%d, %d)\n", - req->bRequestType & 0x03, req->wValue); - switch (req->wValue) { - case 0: /* [Endpoint] halt */ - ep_reset(chip, req->wIndex); - ret = CX_FINISH; - break; - case 1: /* [Device] remote wake-up */ - case 2: /* [Device] test mode */ - default: - ret = CX_STALL; - break; - } - break; - - case USB_REQ_SET_FEATURE: - debug("fotg210: set_feature(%d, %d)\n", - req->wValue, req->wIndex & 0xf); - switch (req->wValue) { - case 0: /* Endpoint Halt */ - id = req->wIndex & 0xf; - setbits_le32(®s->iep[id - 1], IEP_STALL); - setbits_le32(®s->oep[id - 1], OEP_STALL); - ret = CX_FINISH; - break; - case 1: /* Remote Wakeup */ - case 2: /* Test Mode */ - default: - ret = CX_STALL; - break; - } - break; - - case USB_REQ_GET_STATUS: - debug("fotg210: get_status\n"); - ret = CX_STALL; - break; - - case USB_REQ_SET_DESCRIPTOR: - debug("fotg210: set_descriptor\n"); - ret = CX_STALL; - break; - - case USB_REQ_SYNCH_FRAME: - debug("fotg210: sync frame\n"); - ret = CX_STALL; - break; - } - } /* if ((req->bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD) */ - - if (ret == CX_IDLE && chip->driver->setup) { - if (chip->driver->setup(&chip->gadget, req) < 0) - ret = CX_STALL; - else - ret = CX_FINISH; - } - - switch (ret) { - case CX_FINISH: - setbits_le32(®s->cxfifo, CXFIFO_CXFIN); - break; - - case CX_STALL: - setbits_le32(®s->cxfifo, CXFIFO_CXSTALL | CXFIFO_CXFIN); - printf("fotg210: cx_stall!\n"); - break; - - case CX_IDLE: - debug("fotg210: cx_idle?\n"); - default: - break; - } -} - -/* - * fifo - FIFO id - * zlp - zero length packet - */ -static void fotg210_recv(struct fotg210_chip *chip, int ep_id) -{ - struct fotg210_regs *regs = chip->regs; - struct fotg210_ep *ep = chip->ep + ep_id; - struct fotg210_request *req; - int len; - - if (ep->stopped || (ep->desc->bEndpointAddress & USB_DIR_IN)) { - printf("fotg210: ep%d recv, invalid!\n", ep->id); - return; - } - - if (list_empty(&ep->queue)) { - printf("fotg210: ep%d recv, drop!\n", ep->id); - return; - } - - req = list_first_entry(&ep->queue, struct fotg210_request, queue); - len = fotg210_dma(ep, req); - if (len < ep->ep.maxpacket || req->req.length <= req->req.actual) { - list_del_init(&req->queue); - if (req->req.complete) - req->req.complete(&ep->ep, &req->req); - } - - if (ep->id > 0 && list_empty(&ep->queue)) { - setbits_le32(®s->gimr1, - GIMR1_FIFO_RX(ep_to_fifo(chip, ep->id))); - } -} - -/* - * USB Gadget Layer - */ -static int fotg210_ep_enable( - struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc) -{ - struct fotg210_ep *ep = container_of(_ep, struct fotg210_ep, ep); - struct fotg210_chip *chip = ep->chip; - struct fotg210_regs *regs = chip->regs; - int id = ep_to_fifo(chip, ep->id); - int in = (desc->bEndpointAddress & USB_DIR_IN) ? 1 : 0; - - if (!_ep || !desc - || desc->bDescriptorType != USB_DT_ENDPOINT - || le16_to_cpu(desc->wMaxPacketSize) == 0) { - printf("fotg210: bad ep or descriptor\n"); - return -EINVAL; - } - - ep->desc = desc; - ep->stopped = 0; - - if (in) - setbits_le32(®s->fifomap, FIFOMAP(id, FIFOMAP_IN)); - - switch (desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) { - case USB_ENDPOINT_XFER_CONTROL: - return -EINVAL; - - case USB_ENDPOINT_XFER_ISOC: - setbits_le32(®s->fifocfg, - FIFOCFG(id, FIFOCFG_EN | FIFOCFG_ISOC)); - break; - - case USB_ENDPOINT_XFER_BULK: - setbits_le32(®s->fifocfg, - FIFOCFG(id, FIFOCFG_EN | FIFOCFG_BULK)); - break; - - case USB_ENDPOINT_XFER_INT: - setbits_le32(®s->fifocfg, - FIFOCFG(id, FIFOCFG_EN | FIFOCFG_INTR)); - break; - } - - return 0; -} - -static int fotg210_ep_disable(struct usb_ep *_ep) -{ - struct fotg210_ep *ep = container_of(_ep, struct fotg210_ep, ep); - struct fotg210_chip *chip = ep->chip; - struct fotg210_regs *regs = chip->regs; - int id = ep_to_fifo(chip, ep->id); - - ep->desc = NULL; - ep->stopped = 1; - - clrbits_le32(®s->fifocfg, FIFOCFG(id, FIFOCFG_CFG_MASK)); - clrbits_le32(®s->fifomap, FIFOMAP(id, FIFOMAP_DIR_MASK)); - - return 0; -} - -static struct usb_request *fotg210_ep_alloc_request( - struct usb_ep *_ep, gfp_t gfp_flags) -{ - struct fotg210_request *req = malloc(sizeof(*req)); - - if (req) { - memset(req, 0, sizeof(*req)); - INIT_LIST_HEAD(&req->queue); - } - return &req->req; -} - -static void fotg210_ep_free_request( - struct usb_ep *_ep, struct usb_request *_req) -{ - struct fotg210_request *req; - - req = container_of(_req, struct fotg210_request, req); - free(req); -} - -static int fotg210_ep_queue( - struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) -{ - struct fotg210_ep *ep = container_of(_ep, struct fotg210_ep, ep); - struct fotg210_chip *chip = ep->chip; - struct fotg210_regs *regs = chip->regs; - struct fotg210_request *req; - - req = container_of(_req, struct fotg210_request, req); - if (!_req || !_req->complete || !_req->buf - || !list_empty(&req->queue)) { - printf("fotg210: invalid request to ep%d\n", ep->id); - return -EINVAL; - } - - if (!chip || chip->state == USB_STATE_SUSPENDED) { - printf("fotg210: request while chip suspended\n"); - return -EINVAL; - } - - req->req.actual = 0; - req->req.status = -EINPROGRESS; - - if (req->req.length == 0) { - req->req.status = 0; - if (req->req.complete) - req->req.complete(&ep->ep, &req->req); - return 0; - } - - if (ep->id == 0) { - do { - int len = fotg210_dma(ep, req); - if (len < ep->ep.maxpacket) - break; - if (ep->desc->bEndpointAddress & USB_DIR_IN) - udelay(100); - } while (req->req.length > req->req.actual); - } else { - if (ep->desc->bEndpointAddress & USB_DIR_IN) { - do { - int len = fotg210_dma(ep, req); - if (len < ep->ep.maxpacket) - break; - } while (req->req.length > req->req.actual); - } else { - list_add_tail(&req->queue, &ep->queue); - clrbits_le32(®s->gimr1, - GIMR1_FIFO_RX(ep_to_fifo(chip, ep->id))); - } - } - - if (ep->id == 0 || (ep->desc->bEndpointAddress & USB_DIR_IN)) { - if (req->req.complete) - req->req.complete(&ep->ep, &req->req); - } - - return 0; -} - -static int fotg210_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req) -{ - struct fotg210_ep *ep = container_of(_ep, struct fotg210_ep, ep); - struct fotg210_request *req; - - /* make sure it's actually queued on this endpoint */ - list_for_each_entry(req, &ep->queue, queue) { - if (&req->req == _req) - break; - } - if (&req->req != _req) - return -EINVAL; - - /* remove the request */ - list_del_init(&req->queue); - - /* update status & invoke complete callback */ - if (req->req.status == -EINPROGRESS) { - req->req.status = -ECONNRESET; - if (req->req.complete) - req->req.complete(_ep, &req->req); - } - - return 0; -} - -static int fotg210_ep_halt(struct usb_ep *_ep, int halt) -{ - struct fotg210_ep *ep = container_of(_ep, struct fotg210_ep, ep); - struct fotg210_chip *chip = ep->chip; - struct fotg210_regs *regs = chip->regs; - int ret = -1; - - debug("fotg210: ep%d halt=%d\n", ep->id, halt); - - /* Endpoint STALL */ - if (ep->id > 0 && ep->id <= CFG_NUM_ENDPOINTS) { - if (halt) { - /* wait until all ep fifo empty */ - fotg210_cxwait(chip, 0xf00); - /* stall */ - if (ep->desc->bEndpointAddress & USB_DIR_IN) { - setbits_le32(®s->iep[ep->id - 1], - IEP_STALL); - } else { - setbits_le32(®s->oep[ep->id - 1], - OEP_STALL); - } - } else { - if (ep->desc->bEndpointAddress & USB_DIR_IN) { - clrbits_le32(®s->iep[ep->id - 1], - IEP_STALL); - } else { - clrbits_le32(®s->oep[ep->id - 1], - OEP_STALL); - } - } - ret = 0; - } - - return ret; -} - -/* - * activate/deactivate link with host. - */ -static void pullup(struct fotg210_chip *chip, int is_on) -{ - struct fotg210_regs *regs = chip->regs; - - if (is_on) { - if (!chip->pullup) { - chip->state = USB_STATE_POWERED; - chip->pullup = 1; - /* enable the chip */ - setbits_le32(®s->dev_ctrl, DEVCTRL_EN); - /* clear unplug bit (BIT0) */ - clrbits_le32(®s->phy_tmsr, PHYTMSR_UNPLUG); - } - } else { - chip->state = USB_STATE_NOTATTACHED; - chip->pullup = 0; - chip->addr = 0; - writel(chip->addr, ®s->dev_addr); - /* set unplug bit (BIT0) */ - setbits_le32(®s->phy_tmsr, PHYTMSR_UNPLUG); - /* disable the chip */ - clrbits_le32(®s->dev_ctrl, DEVCTRL_EN); - } -} - -static int fotg210_pullup(struct usb_gadget *_gadget, int is_on) -{ - struct fotg210_chip *chip; - - chip = container_of(_gadget, struct fotg210_chip, gadget); - - debug("fotg210: pullup=%d\n", is_on); - - pullup(chip, is_on); - - return 0; -} - -static int fotg210_get_frame(struct usb_gadget *_gadget) -{ - struct fotg210_chip *chip; - struct fotg210_regs *regs; - - chip = container_of(_gadget, struct fotg210_chip, gadget); - regs = chip->regs; - - return SOFFNR_FNR(readl(®s->sof_fnr)); -} - -static struct usb_gadget_ops fotg210_gadget_ops = { - .get_frame = fotg210_get_frame, - .pullup = fotg210_pullup, -}; - -static struct usb_ep_ops fotg210_ep_ops = { - .enable = fotg210_ep_enable, - .disable = fotg210_ep_disable, - .queue = fotg210_ep_queue, - .dequeue = fotg210_ep_dequeue, - .set_halt = fotg210_ep_halt, - .alloc_request = fotg210_ep_alloc_request, - .free_request = fotg210_ep_free_request, -}; - -static struct fotg210_chip controller = { - .regs = (void __iomem *)CONFIG_FOTG210_BASE, - .gadget = { - .name = "fotg210_udc", - .ops = &fotg210_gadget_ops, - .ep0 = &controller.ep[0].ep, - .speed = USB_SPEED_UNKNOWN, - .is_dualspeed = 1, - .is_otg = 0, - .is_a_peripheral = 0, - .b_hnp_enable = 0, - .a_hnp_support = 0, - .a_alt_hnp_support = 0, - }, - .ep[0] = { - .id = 0, - .ep = { - .name = "ep0", - .ops = &fotg210_ep_ops, - }, - .desc = &ep0_desc, - .chip = &controller, - .maxpacket = CFG_EP0_MAX_PACKET_SIZE, - }, - .ep[1] = { - .id = 1, - .ep = { - .name = "ep1", - .ops = &fotg210_ep_ops, - }, - .chip = &controller, - .maxpacket = CFG_EPX_MAX_PACKET_SIZE, - }, - .ep[2] = { - .id = 2, - .ep = { - .name = "ep2", - .ops = &fotg210_ep_ops, - }, - .chip = &controller, - .maxpacket = CFG_EPX_MAX_PACKET_SIZE, - }, - .ep[3] = { - .id = 3, - .ep = { - .name = "ep3", - .ops = &fotg210_ep_ops, - }, - .chip = &controller, - .maxpacket = CFG_EPX_MAX_PACKET_SIZE, - }, - .ep[4] = { - .id = 4, - .ep = { - .name = "ep4", - .ops = &fotg210_ep_ops, - }, - .chip = &controller, - .maxpacket = CFG_EPX_MAX_PACKET_SIZE, - }, -}; - -int usb_gadget_handle_interrupts(int index) -{ - struct fotg210_chip *chip = &controller; - struct fotg210_regs *regs = chip->regs; - uint32_t id, st, isr, gisr; - - isr = readl(®s->isr) & (~readl(®s->imr)); - gisr = readl(®s->gisr) & (~readl(®s->gimr)); - if (!(isr & ISR_DEV) || !gisr) - return 0; - - writel(ISR_DEV, ®s->isr); - - /* CX interrupts */ - if (gisr & GISR_GRP0) { - st = readl(®s->gisr0); - /* - * Write 1 and then 0 works for both W1C & RW. - * - * HW v1.11.0+: It's a W1C register (write 1 clear) - * HW v1.10.0-: It's a R/W register (write 0 clear) - */ - writel(st & GISR0_CXABORT, ®s->gisr0); - writel(0, ®s->gisr0); - - if (st & GISR0_CXERR) - printf("fotg210: cmd error\n"); - - if (st & GISR0_CXABORT) - printf("fotg210: cmd abort\n"); - - if (st & GISR0_CXSETUP) /* setup */ - fotg210_setup(chip); - else if (st & GISR0_CXEND) /* command finish */ - setbits_le32(®s->cxfifo, CXFIFO_CXFIN); - } - - /* FIFO interrupts */ - if (gisr & GISR_GRP1) { - st = readl(®s->gisr1); - for (id = 0; id < 4; ++id) { - if (st & GISR1_RX_FIFO(id)) - fotg210_recv(chip, fifo_to_ep(chip, id, 0)); - } - } - - /* Device Status Interrupts */ - if (gisr & GISR_GRP2) { - st = readl(®s->gisr2); - /* - * Write 1 and then 0 works for both W1C & RW. - * - * HW v1.11.0+: It's a W1C register (write 1 clear) - * HW v1.10.0-: It's a R/W register (write 0 clear) - */ - writel(st, ®s->gisr2); - writel(0, ®s->gisr2); - - if (st & GISR2_RESET) - printf("fotg210: reset by host\n"); - else if (st & GISR2_SUSPEND) - printf("fotg210: suspend/removed\n"); - else if (st & GISR2_RESUME) - printf("fotg210: resume\n"); - - /* Errors */ - if (st & GISR2_ISOCERR) - printf("fotg210: iso error\n"); - if (st & GISR2_ISOCABT) - printf("fotg210: iso abort\n"); - if (st & GISR2_DMAERR) - printf("fotg210: dma error\n"); - } - - return 0; -} - -int usb_gadget_register_driver(struct usb_gadget_driver *driver) -{ - int i, ret = 0; - struct fotg210_chip *chip = &controller; - - if (!driver || !driver->bind || !driver->setup) { - puts("fotg210: bad parameter.\n"); - return -EINVAL; - } - - INIT_LIST_HEAD(&chip->gadget.ep_list); - for (i = 0; i < CFG_NUM_ENDPOINTS + 1; ++i) { - struct fotg210_ep *ep = chip->ep + i; - - ep->ep.maxpacket = ep->maxpacket; - INIT_LIST_HEAD(&ep->queue); - - if (ep->id == 0) { - ep->stopped = 0; - } else { - ep->stopped = 1; - list_add_tail(&ep->ep.ep_list, &chip->gadget.ep_list); - } - } - - if (fotg210_reset(chip)) { - puts("fotg210: reset failed.\n"); - return -EINVAL; - } - - ret = driver->bind(&chip->gadget); - if (ret) { - debug("fotg210: driver->bind() returned %d\n", ret); - return ret; - } - chip->driver = driver; - - return ret; -} - -int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) -{ - struct fotg210_chip *chip = &controller; - - driver->unbind(&chip->gadget); - chip->driver = NULL; - - pullup(chip, 0); - - return 0; -} diff --git a/drivers/usb/gadget/gadget_chips.h b/drivers/usb/gadget/gadget_chips.h index abc6dc7f89f..98156c312d2 100644 --- a/drivers/usb/gadget/gadget_chips.h +++ b/drivers/usb/gadget/gadget_chips.h @@ -117,12 +117,6 @@ #define gadget_is_ci(g) 0 #endif -#ifdef CONFIG_USB_GADGET_FOTG210 -#define gadget_is_fotg210(g) (!strcmp("fotg210_udc", (g)->name)) -#else -#define gadget_is_fotg210(g) 0 -#endif - #ifdef CONFIG_USB_DWC3_GADGET #define gadget_is_dwc3(g) (!strcmp("dwc3-gadget", (g)->name)) #else @@ -202,8 +196,6 @@ static inline int usb_gadget_controller_number(struct usb_gadget *gadget) return 0x20; else if (gadget_is_ci(gadget)) return 0x21; - else if (gadget_is_fotg210(gadget)) - return 0x22; else if (gadget_is_dwc3(gadget)) return 0x23; else if (gadget_is_cdns3(gadget)) diff --git a/include/usb/fotg210.h b/include/usb/fotg210.h deleted file mode 100644 index 292ce54e0c4..00000000000 --- a/include/usb/fotg210.h +++ /dev/null @@ -1,362 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Faraday USB 2.0 OTG Controller - * - * (C) Copyright 2010 Faraday Technology - * Dante Su <dantesu@faraday-tech.com> - */ - -#ifndef _FOTG210_H -#define _FOTG210_H - -struct fotg210_regs { - /* USB Host Controller */ - struct { - uint32_t data[4]; - } hccr; /* 0x00 - 0x0f: hccr */ - struct { - uint32_t data[9]; - } hcor; /* 0x10 - 0x33: hcor */ - uint32_t rsvd1[3]; - uint32_t miscr; /* 0x40: Miscellaneous Register */ - uint32_t rsvd2[15]; - /* USB OTG Controller */ - uint32_t otgcsr;/* 0x80: OTG Control Status Register */ - uint32_t otgisr;/* 0x84: OTG Interrupt Status Register */ - uint32_t otgier;/* 0x88: OTG Interrupt Enable Register */ - uint32_t rsvd3[13]; - uint32_t isr; /* 0xC0: Global Interrupt Status Register */ - uint32_t imr; /* 0xC4: Global Interrupt Mask Register */ - uint32_t rsvd4[14]; - /* USB Device Controller */ - uint32_t dev_ctrl;/* 0x100: Device Control Register */ - uint32_t dev_addr;/* 0x104: Device Address Register */ - uint32_t dev_test;/* 0x108: Device Test Register */ - uint32_t sof_fnr; /* 0x10c: SOF Frame Number Register */ - uint32_t sof_mtr; /* 0x110: SOF Mask Timer Register */ - uint32_t phy_tmsr;/* 0x114: PHY Test Mode Selector Register */ - uint32_t rsvd5[2]; - uint32_t cxfifo;/* 0x120: CX FIFO Register */ - uint32_t idle; /* 0x124: IDLE Counter Register */ - uint32_t rsvd6[2]; - uint32_t gimr; /* 0x130: Group Interrupt Mask Register */ - uint32_t gimr0; /* 0x134: Group Interrupt Mask Register 0 */ - uint32_t gimr1; /* 0x138: Group Interrupt Mask Register 1 */ - uint32_t gimr2; /* 0x13c: Group Interrupt Mask Register 2 */ - uint32_t gisr; /* 0x140: Group Interrupt Status Register */ - uint32_t gisr0; /* 0x144: Group Interrupt Status Register 0 */ - uint32_t gisr1; /* 0x148: Group Interrupt Status Register 1 */ - uint32_t gisr2; /* 0x14c: Group Interrupt Status Register 2 */ - uint32_t rxzlp; /* 0x150: Receive Zero-Length-Packet Register */ - uint32_t txzlp; /* 0x154: Transfer Zero-Length-Packet Register */ - uint32_t isoeasr;/* 0x158: ISOC Error/Abort Status Register */ - uint32_t rsvd7[1]; - uint32_t iep[8]; /* 0x160 - 0x17f: IN Endpoint Register */ - uint32_t oep[8]; /* 0x180 - 0x19f: OUT Endpoint Register */ - uint32_t epmap14;/* 0x1a0: Endpoint Map Register (EP1 ~ 4) */ - uint32_t epmap58;/* 0x1a4: Endpoint Map Register (EP5 ~ 8) */ - uint32_t fifomap;/* 0x1a8: FIFO Map Register */ - uint32_t fifocfg; /* 0x1ac: FIFO Configuration Register */ - uint32_t fifocsr[4];/* 0x1b0 - 0x1bf: FIFO Control Status Register */ - uint32_t dma_fifo; /* 0x1c0: DMA Target FIFO Register */ - uint32_t rsvd8[1]; - uint32_t dma_ctrl; /* 0x1c8: DMA Control Register */ - uint32_t dma_addr; /* 0x1cc: DMA Address Register */ - uint32_t ep0_data; /* 0x1d0: EP0 Setup Packet PIO Register */ -}; - -/* Miscellaneous Register */ -#define MISCR_SUSPEND (1 << 6) /* Put transceiver in suspend mode */ -#define MISCR_EOF2(x) (((x) & 0x3) << 4) /* EOF 2 Timing */ -#define MISCR_EOF1(x) (((x) & 0x3) << 2) /* EOF 1 Timing */ -#define MISCR_ASST(x) (((x) & 0x3) << 0) /* Async. Sched. Sleep Timer */ - -/* OTG Control Status Register */ -#define OTGCSR_SPD_HIGH (2 << 22) /* Speed of the attached device (host) */ -#define OTGCSR_SPD_LOW (1 << 22) -#define OTGCSR_SPD_FULL (0 << 22) -#define OTGCSR_SPD_MASK (3 << 22) -#define OTGCSR_SPD_SHIFT 22 -#define OTGCSR_SPD(x) (((x) >> 22) & 0x03) -#define OTGCSR_DEV_A (0 << 21) /* Acts as A-device */ -#define OTGCSR_DEV_B (1 << 21) /* Acts as B-device */ -#define OTGCSR_ROLE_H (0 << 20) /* Acts as Host */ -#define OTGCSR_ROLE_D (1 << 20) /* Acts as Device */ -#define OTGCSR_A_VBUS_VLD (1 << 19) /* A-device VBUS Valid */ -#define OTGCSR_A_SESS_VLD (1 << 18) /* A-device Session Valid */ -#define OTGCSR_B_SESS_VLD (1 << 17) /* B-device Session Valid */ -#define OTGCSR_B_SESS_END (1 << 16) /* B-device Session End */ -#define OTGCSR_HFT_LONG (1 << 11) /* HDISCON noise filter = 270 us*/ -#define OTGCSR_HFT (0 << 11) /* HDISCON noise filter = 135 us*/ -#define OTGCSR_VFT_LONG (1 << 10) /* VBUS noise filter = 472 us*/ -#define OTGCSR_VFT (0 << 10) /* VBUS noise filter = 135 us*/ -#define OTGCSR_IDFT_LONG (1 << 9) /* ID noise filter = 4 ms*/ -#define OTGCSR_IDFT (0 << 9) /* ID noise filter = 3 ms*/ -#define OTGCSR_A_SRPR_VBUS (0 << 8) /* A-device: SRP responds to VBUS */ -#define OTGCSR_A_SRPR_DATA (1 << 8) /* A-device: SRP responds to DATA-LINE */ -#define OTGCSR_A_SRP_EN (1 << 7) /* A-device SRP detection enabled */ -#define OTGCSR_A_HNP (1 << 6) /* Set role=A-device with HNP enabled */ -#define OTGCSR_A_BUSDROP (1 << 5) /* A-device drop bus (power-down) */ -#define OTGCSR_A_BUSREQ (1 << 4) /* A-device request bus */ -#define OTGCSR_B_VBUS_DISC (1 << 2) /* B-device discharges VBUS */ -#define OTGCSR_B_HNP (1 << 1) /* B-device enable HNP */ -#define OTGCSR_B_BUSREQ (1 << 0) /* B-device request bus */ - -/* OTG Interrupt Status Register */ -#define OTGISR_APRM (1 << 12) /* Mini-A plug removed */ -#define OTGISR_BPRM (1 << 11) /* Mini-B plug removed */ -#define OTGISR_OVD (1 << 10) /* over-current detected */ -#define OTGISR_IDCHG (1 << 9) /* ID(A/B) changed */ -#define OTGISR_RLCHG (1 << 8) /* Role(Host/Device) changed */ -#define OTGISR_BSESSEND (1 << 6) /* B-device Session End */ -#define OTGISR_AVBUSERR (1 << 5) /* A-device VBUS Error */ -#define OTGISR_ASRP (1 << 4) /* A-device SRP detected */ -#define OTGISR_BSRP (1 << 0) /* B-device SRP complete */ - -/* OTG Interrupt Enable Register */ -#define OTGIER_APRM (1 << 12) /* Mini-A plug removed */ -#define OTGIER_BPRM (1 << 11) /* Mini-B plug removed */ -#define OTGIER_OVD (1 << 10) /* over-current detected */ -#define OTGIER_IDCHG (1 << 9) /* ID(A/B) changed */ -#define OTGIER_RLCHG (1 << 8) /* Role(Host/Device) changed */ -#define OTGIER_BSESSEND (1 << 6) /* B-device Session End */ -#define OTGIER_AVBUSERR (1 << 5) /* A-device VBUS Error */ -#define OTGIER_ASRP (1 << 4) /* A-device SRP detected */ -#define OTGIER_BSRP (1 << 0) /* B-device SRP complete */ - -/* Global Interrupt Status Register (W1C) */ -#define ISR_HOST (1 << 2) /* USB Host interrupt */ -#define ISR_OTG (1 << 1) /* USB OTG interrupt */ -#define ISR_DEV (1 << 0) /* USB Device interrupt */ -#define ISR_MASK 0x07 - -/* Global Interrupt Mask Register */ -#define IMR_IRQLH (1 << 3) /* Interrupt triggered at level-high */ -#define IMR_IRQLL (0 << 3) /* Interrupt triggered at level-low */ -#define IMR_HOST (1 << 2) /* USB Host interrupt */ -#define IMR_OTG (1 << 1) /* USB OTG interrupt */ -#define IMR_DEV (1 << 0) /* USB Device interrupt */ -#define IMR_MASK 0x0f - -/* Device Control Register */ -#define DEVCTRL_FS_FORCED (1 << 9) /* Forced to be Full-Speed Mode */ -#define DEVCTRL_HS (1 << 6) /* High Speed Mode */ -#define DEVCTRL_FS (0 << 6) /* Full Speed Mode */ -#define DEVCTRL_EN (1 << 5) /* Chip Enable */ -#define DEVCTRL_RESET (1 << 4) /* Chip Software Reset */ -#define DEVCTRL_SUSPEND (1 << 3) /* Enter Suspend Mode */ -#define DEVCTRL_GIRQ_EN (1 << 2) /* Global Interrupt Enabled */ -#define DEVCTRL_HALFSPD (1 << 1) /* Half speed mode for FPGA test */ -#define DEVCTRL_RWAKEUP (1 << 0) /* Enable remote wake-up */ - -/* Device Address Register */ -#define DEVADDR_CONF (1 << 7) /* SET_CONFIGURATION has been executed */ -#define DEVADDR_ADDR(x) ((x) & 0x7f) -#define DEVADDR_ADDR_MASK 0x7f - -/* Device Test Register */ -#define DEVTEST_NOSOF (1 << 6) /* Do not generate SOF */ -#define DEVTEST_TST_MODE (1 << 5) /* Enter Test Mode */ -#define DEVTEST_TST_NOTS (1 << 4) /* Do not toggle sequence */ -#define DEVTEST_TST_NOCRC (1 << 3) /* Do not append CRC */ -#define DEVTEST_TST_CLREA (1 << 2) /* Clear External Side Address */ -#define DEVTEST_TST_CXLP (1 << 1) /* EP0 loopback test */ -#define DEVTEST_TST_CLRFF (1 << 0) /* Clear FIFO */ - -/* SOF Frame Number Register */ -#define SOFFNR_UFN(x) (((x) >> 11) & 0x7) /* SOF Micro-Frame Number */ -#define SOFFNR_FNR(x) ((x) & 0x7ff) /* SOF Frame Number */ - -/* SOF Mask Timer Register */ -#define SOFMTR_TMR(x) ((x) & 0xffff) - -/* PHY Test Mode Selector Register */ -#define PHYTMSR_TST_PKT (1 << 4) /* Packet send test */ -#define PHYTMSR_TST_SE0NAK (1 << 3) /* High-Speed quiescent state */ -#define PHYTMSR_TST_KSTA (1 << 2) /* High-Speed K state */ -#define PHYTMSR_TST_JSTA (1 << 1) /* High-Speed J state */ -#define PHYTMSR_UNPLUG (1 << 0) /* Enable soft-detachment */ - -/* CX FIFO Register */ -#define CXFIFO_BYTES(x) (((x) >> 24) & 0x7f) /* CX/EP0 FIFO byte count */ -#define CXFIFO_FIFOE(x) (1 << (((x) & 0x03) + 8)) /* EPx FIFO empty */ -#define CXFIFO_FIFOE_FIFO0 (1 << 8) -#define CXFIFO_FIFOE_FIFO1 (1 << 9) -#define CXFIFO_FIFOE_FIFO2 (1 << 10) -#define CXFIFO_FIFOE_FIFO3 (1 << 11) -#define CXFIFO_FIFOE_MASK (0x0f << 8) -#define CXFIFO_CXFIFOE (1 << 5) /* CX FIFO empty */ -#define CXFIFO_CXFIFOF (1 << 4) /* CX FIFO full */ -#define CXFIFO_CXFIFOCLR (1 << 3) /* CX FIFO clear */ -#define CXFIFO_CXSTALL (1 << 2) /* CX Stall */ -#define CXFIFO_TSTPKTFIN (1 << 1) /* Test packet data transfer finished */ -#define CXFIFO_CXFIN (1 << 0) /* CX data transfer finished */ - -/* IDLE Counter Register */ -#define IDLE_MS(x) ((x) & 0x07) /* PHY suspend delay = x ms */ - -/* Group Interrupt Mask(Disable) Register */ -#define GIMR_GRP2 (1 << 2) /* Disable interrupt group 2 */ -#define GIMR_GRP1 (1 << 1) /* Disable interrupt group 1 */ -#define GIMR_GRP0 (1 << 0) /* Disable interrupt group 0 */ -#define GIMR_MASK 0x07 - -/* Group Interrupt Mask(Disable) Register 0 (CX) */ -#define GIMR0_CXABORT (1 << 5) /* CX command abort interrupt */ -#define GIMR0_CXERR (1 << 4) /* CX command error interrupt */ -#define GIMR0_CXEND (1 << 3) /* CX command end interrupt */ -#define GIMR0_CXOUT (1 << 2) /* EP0-OUT packet interrupt */ -#define GIMR0_CXIN (1 << 1) /* EP0-IN packet interrupt */ -#define GIMR0_CXSETUP (1 << 0) /* EP0-SETUP packet interrupt */ -#define GIMR0_MASK 0x3f - -/* Group Interrupt Mask(Disable) Register 1 (FIFO) */ -#define GIMR1_FIFO_IN(x) (1 << (((x) & 3) + 16)) /* FIFOx IN */ -#define GIMR1_FIFO_TX(x) GIMR1_FIFO_IN(x) -#define GIMR1_FIFO_OUT(x) (1 << (((x) & 3) * 2)) /* FIFOx OUT */ -#define GIMR1_FIFO_SPK(x) (1 << (((x) & 3) * 2 + 1)) /* FIFOx SHORT PACKET */ -#define GIMR1_FIFO_RX(x) (GIMR1_FIFO_OUT(x) | GIMR1_FIFO_SPK(x)) -#define GIMR1_MASK 0xf00ff - -/* Group Interrupt Mask(Disable) Register 2 (Device) */ -#define GIMR2_WAKEUP (1 << 10) /* Device waked up */ -#define GIMR2_IDLE (1 << 9) /* Device idle */ -#define GIMR2_DMAERR (1 << 8) /* DMA error */ -#define GIMR2_DMAFIN (1 << 7) /* DMA finished */ -#define GIMR2_ZLPRX (1 << 6) /* Zero-Length-Packet Rx Interrupt */ -#define GIMR2_ZLPTX (1 << 5) /* Zero-Length-Packet Tx Interrupt */ -#define GIMR2_ISOCABT (1 << 4) /* ISOC Abort Interrupt */ -#define GIMR2_ISOCERR (1 << 3) /* ISOC Error Interrupt */ -#define GIMR2_RESUME (1 << 2) /* Resume state change Interrupt */ -#define GIMR2_SUSPEND (1 << 1) /* Suspend state change Interrupt */ -#define GIMR2_RESET (1 << 0) /* Reset Interrupt */ -#define GIMR2_MASK 0x7ff - -/* Group Interrupt Status Register */ -#define GISR_GRP2 (1 << 2) /* Interrupt group 2 */ -#define GISR_GRP1 (1 << 1) /* Interrupt group 1 */ -#define GISR_GRP0 (1 << 0) /* Interrupt group 0 */ - -/* Group Interrupt Status Register 0 (CX) */ -#define GISR0_CXABORT (1 << 5) /* CX command abort interrupt */ -#define GISR0_CXERR (1 << 4) /* CX command error interrupt */ -#define GISR0_CXEND (1 << 3) /* CX command end interrupt */ -#define GISR0_CXOUT (1 << 2) /* EP0-OUT packet interrupt */ -#define GISR0_CXIN (1 << 1) /* EP0-IN packet interrupt */ -#define GISR0_CXSETUP (1 << 0) /* EP0-SETUP packet interrupt */ - -/* Group Interrupt Status Register 1 (FIFO) */ -#define GISR1_IN_FIFO(x) (1 << (((x) & 0x03) + 16)) /* FIFOx IN */ -#define GISR1_OUT_FIFO(x) (1 << (((x) & 0x03) * 2)) /* FIFOx OUT */ -#define GISR1_SPK_FIFO(x) (1 << (((x) & 0x03) * 2 + 1)) /* FIFOx SPK */ -#define GISR1_RX_FIFO(x) (3 << (((x) & 0x03) * 2)) /* FIFOx OUT/SPK */ - -/* Group Interrupt Status Register 2 (Device) */ -#define GISR2_WAKEUP (1 << 10) /* Device waked up */ -#define GISR2_IDLE (1 << 9) /* Device idle */ -#define GISR2_DMAERR (1 << 8) /* DMA error */ -#define GISR2_DMAFIN (1 << 7) /* DMA finished */ -#define GISR2_ZLPRX (1 << 6) /* Zero-Length-Packet Rx Interrupt */ -#define GISR2_ZLPTX (1 << 5) /* Zero-Length-Packet Tx Interrupt */ -#define GISR2_ISOCABT (1 << 4) /* ISOC Abort Interrupt */ -#define GISR2_ISOCERR (1 << 3) /* ISOC Error Interrupt */ -#define GISR2_RESUME (1 << 2) /* Resume state change Interrupt */ -#define GISR2_SUSPEND (1 << 1) /* Suspend state change Interrupt */ -#define GISR2_RESET (1 << 0) /* Reset Interrupt */ - -/* Receive Zero-Length-Packet Register */ -#define RXZLP_EP(x) (1 << ((x) - 1)) /* EPx ZLP rx interrupt */ - -/* Transfer Zero-Length-Packet Register */ -#define TXZLP_EP(x) (1 << ((x) - 1)) /* EPx ZLP tx interrupt */ - -/* ISOC Error/Abort Status Register */ -#define ISOEASR_EP(x) (0x10001 << ((x) - 1)) /* EPx ISOC Error/Abort */ - -/* IN Endpoint Register */ -#define IEP_SENDZLP (1 << 15) /* Send Zero-Length-Packet */ -#define IEP_TNRHB(x) (((x) & 0x03) << 13) \ - /* Transaction Number for High-Bandwidth EP(ISOC) */ -#define IEP_RESET (1 << 12) /* Reset Toggle Sequence */ -#define IEP_STALL (1 << 11) /* Stall */ -#define IEP_MAXPS(x) ((x) & 0x7ff) /* Max. packet size */ - -/* OUT Endpoint Register */ -#define OEP_RESET (1 << 12) /* Reset Toggle Sequence */ -#define OEP_STALL (1 << 11) /* Stall */ -#define OEP_MAXPS(x) ((x) & 0x7ff) /* Max. packet size */ - -/* Endpoint Map Register (EP1 ~ EP4) */ -#define EPMAP14_SET_IN(ep, fifo) \ - ((fifo) & 3) << (((ep) - 1) << 3 + 0) -#define EPMAP14_SET_OUT(ep, fifo) \ - ((fifo) & 3) << (((ep) - 1) << 3 + 4) -#define EPMAP14_SET(ep, in, out) \ - do { \ - EPMAP14_SET_IN(ep, in); \ - EPMAP14_SET_OUT(ep, out); \ - } while (0) - -#define EPMAP14_DEFAULT 0x33221100 /* EP1->FIFO0, EP2->FIFO1... */ - -/* Endpoint Map Register (EP5 ~ EP8) */ -#define EPMAP58_SET_IN(ep, fifo) \ - ((fifo) & 3) << (((ep) - 5) << 3 + 0) -#define EPMAP58_SET_OUT(ep, fifo) \ - ((fifo) & 3) << (((ep) - 5) << 3 + 4) -#define EPMAP58_SET(ep, in, out) \ - do { \ - EPMAP58_SET_IN(ep, in); \ - EPMAP58_SET_OUT(ep, out); \ - } while (0) - -#define EPMAP58_DEFAULT 0x00000000 /* All EPx->FIFO0 */ - -/* FIFO Map Register */ -#define FIFOMAP_BIDIR (2 << 4) -#define FIFOMAP_IN (1 << 4) -#define FIFOMAP_OUT (0 << 4) -#define FIFOMAP_DIR_MASK 0x30 -#define FIFOMAP_EP(x) ((x) & 0x0f) -#define FIFOMAP_EP_MASK 0x0f -#define FIFOMAP_CFG_MASK 0x3f -#define FIFOMAP_DEFAULT 0x04030201 /* FIFO0->EP1, FIFO1->EP2... */ -#define FIFOMAP(fifo, cfg) (((cfg) & 0x3f) << (((fifo) & 3) << 3)) - -/* FIFO Configuration Register */ -#define FIFOCFG_EN (1 << 5) -#define FIFOCFG_BLKSZ_1024 (1 << 4) -#define FIFOCFG_BLKSZ_512 (0 << 4) -#define FIFOCFG_3BLK (2 << 2) -#define FIFOCFG_2BLK (1 << 2) -#define FIFOCFG_1BLK (0 << 2) -#define FIFOCFG_NBLK_MASK 3 -#define FIFOCFG_NBLK_SHIFT 2 -#define FIFOCFG_INTR (3 << 0) -#define FIFOCFG_BULK (2 << 0) -#define FIFOCFG_ISOC (1 << 0) -#define FIFOCFG_RSVD (0 << 0) /* Reserved */ -#define FIFOCFG_TYPE_MASK 3 -#define FIFOCFG_TYPE_SHIFT 0 -#define FIFOCFG_CFG_MASK 0x3f -#define FIFOCFG(fifo, cfg) (((cfg) & 0x3f) << (((fifo) & 3) << 3)) - -/* FIFO Control Status Register */ -#define FIFOCSR_RESET (1 << 12) /* FIFO Reset */ -#define FIFOCSR_BYTES(x) ((x) & 0x7ff) /* Length(bytes) for OUT-EP/FIFO */ - -/* DMA Target FIFO Register */ -#define DMAFIFO_CX (1 << 4) /* DMA FIFO = CX FIFO */ -#define DMAFIFO_FIFO(x) (1 << ((x) & 0x3)) /* DMA FIFO = FIFOx */ - -/* DMA Control Register */ -#define DMACTRL_LEN(x) (((x) & 0x1ffff) << 8) /* DMA length (Bytes) */ -#define DMACTRL_LEN_SHIFT 8 -#define DMACTRL_CLRFF (1 << 4) /* Clear FIFO upon DMA abort */ -#define DMACTRL_ABORT (1 << 3) /* DMA abort */ -#define DMACTRL_IO2IO (1 << 2) /* IO to IO */ -#define DMACTRL_FIFO2MEM (0 << 1) /* FIFO to Memory */ -#define DMACTRL_MEM2FIFO (1 << 1) /* Memory to FIFO */ -#define DMACTRL_START (1 << 0) /* DMA start */ - -#endif -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* Re: [PATCH v3 68/76] usb: Drop unused fotg210 gadget 2023-02-01 20:20 ` [PATCH v3 68/76] usb: Drop unused fotg210 gadget Simon Glass @ 2023-02-10 23:33 ` Samuel Holland 2023-02-11 1:06 ` Tom Rini 0 siblings, 1 reply; 87+ messages in thread From: Samuel Holland @ 2023-02-10 23:33 UTC (permalink / raw) To: Simon Glass; +Cc: Tom Rini, Marek Vasut, u-boot On 2/1/23 14:20, Simon Glass wrote: > This is not used and appears to be associated with the faraday board which > has been removed. Drop the driver and Kconfig options. > > Signed-off-by: Simon Glass <sjg@chromium.org> > --- > > (no changes since v1) > > drivers/usb/gadget/Makefile | 3 +- > drivers/usb/gadget/fotg210.c | 964 ------------------------------ > drivers/usb/gadget/gadget_chips.h | 8 - > include/usb/fotg210.h | 362 ----------- > 4 files changed, 1 insertion(+), 1336 deletions(-) > delete mode 100644 drivers/usb/gadget/fotg210.c > delete mode 100644 include/usb/fotg210.h > > diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile > index 9c04403da30..b04b6bcd779 100644 > --- a/drivers/usb/gadget/Makefile > +++ b/drivers/usb/gadget/Makefile > @@ -19,8 +19,7 @@ obj-$(CONFIG_USB_GADGET_ATMEL_USBA) += atmel_usba_udc.o > obj-$(CONFIG_USB_GADGET_BCM_UDC_OTG_PHY) += bcm_udc_otg_phy.o > obj-$(CONFIG_USB_GADGET_DWC2_OTG) += dwc2_udc_otg.o > obj-$(CONFIG_USB_GADGET_DWC2_OTG_PHY) += dwc2_udc_otg_phy.o > -obj-$(CONFIG_USB_GADGET_FOTG210) += fotg210.o > -obj-$(CONFIG_USB_GADGET_MAX3420) += max3420_udc.o > +0obj-$(CONFIG_USB_GADGET_MAX3420) += max3420_udc.o This stray 0 breaks the next line of the Makefile. Regards, Samuel ^ permalink raw reply [flat|nested] 87+ messages in thread
* Re: [PATCH v3 68/76] usb: Drop unused fotg210 gadget 2023-02-10 23:33 ` Samuel Holland @ 2023-02-11 1:06 ` Tom Rini 0 siblings, 0 replies; 87+ messages in thread From: Tom Rini @ 2023-02-11 1:06 UTC (permalink / raw) To: Samuel Holland; +Cc: Simon Glass, Marek Vasut, u-boot [-- Attachment #1: Type: text/plain, Size: 1636 bytes --] On Fri, Feb 10, 2023 at 05:33:13PM -0600, Samuel Holland wrote: > On 2/1/23 14:20, Simon Glass wrote: > > This is not used and appears to be associated with the faraday board which > > has been removed. Drop the driver and Kconfig options. > > > > Signed-off-by: Simon Glass <sjg@chromium.org> > > --- > > > > (no changes since v1) > > > > drivers/usb/gadget/Makefile | 3 +- > > drivers/usb/gadget/fotg210.c | 964 ------------------------------ > > drivers/usb/gadget/gadget_chips.h | 8 - > > include/usb/fotg210.h | 362 ----------- > > 4 files changed, 1 insertion(+), 1336 deletions(-) > > delete mode 100644 drivers/usb/gadget/fotg210.c > > delete mode 100644 include/usb/fotg210.h > > > > diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile > > index 9c04403da30..b04b6bcd779 100644 > > --- a/drivers/usb/gadget/Makefile > > +++ b/drivers/usb/gadget/Makefile > > @@ -19,8 +19,7 @@ obj-$(CONFIG_USB_GADGET_ATMEL_USBA) += atmel_usba_udc.o > > obj-$(CONFIG_USB_GADGET_BCM_UDC_OTG_PHY) += bcm_udc_otg_phy.o > > obj-$(CONFIG_USB_GADGET_DWC2_OTG) += dwc2_udc_otg.o > > obj-$(CONFIG_USB_GADGET_DWC2_OTG_PHY) += dwc2_udc_otg_phy.o > > -obj-$(CONFIG_USB_GADGET_FOTG210) += fotg210.o > > -obj-$(CONFIG_USB_GADGET_MAX3420) += max3420_udc.o > > +0obj-$(CONFIG_USB_GADGET_MAX3420) += max3420_udc.o > > This stray 0 breaks the next line of the Makefile. Little worried that didn't cause some failure to build elsewhere, honestly, I guess because USB_GADGET_MAX3420 isn't used either? But I'll push a fix with a Reported-by soon, thanks! -- Tom [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 659 bytes --] ^ permalink raw reply [flat|nested] 87+ messages in thread
* [PATCH v3 69/76] rmobile: Drop unused ehci-rmobile driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (64 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 68/76] usb: Drop unused fotg210 gadget Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 70/76] usb: Drop unused ehci-vct driver Simon Glass ` (6 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Nobuhiro Iwamatsu This is not used. Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) .../mach-rmobile/include/mach/ehci-rmobile.h | 146 ------------------ drivers/usb/host/Makefile | 1 - drivers/usb/host/ehci-rmobile.c | 129 ---------------- 3 files changed, 276 deletions(-) delete mode 100644 arch/arm/mach-rmobile/include/mach/ehci-rmobile.h delete mode 100644 drivers/usb/host/ehci-rmobile.c diff --git a/arch/arm/mach-rmobile/include/mach/ehci-rmobile.h b/arch/arm/mach-rmobile/include/mach/ehci-rmobile.h deleted file mode 100644 index ca8c5f37063..00000000000 --- a/arch/arm/mach-rmobile/include/mach/ehci-rmobile.h +++ /dev/null @@ -1,146 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* - * Copyright (C) 2013,2014 Renesas Electronics Corporation - * Copyright (C) 2014 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> - */ - -#ifndef __EHCI_RMOBILE_H__ -#define __EHCI_RMOBILE_H__ - -/* Register offset */ -#define OHCI_OFFSET 0x00 -#define OHCI_SIZE 0x1000 -#define EHCI_OFFSET 0x1000 -#define EHCI_SIZE 0x1000 - -#define EHCI_USBCMD (EHCI_OFFSET + 0x0020) - -/* USBCTR */ -#define DIRPD (1 << 8) -#define PLL_RST (1 << 2) -#define PCICLK_MASK (1 << 1) -#define USBH_RST (1 << 0) - -/* CMND_STS */ -#define SERREN (1 << 8) -#define PERREN (1 << 6) -#define MASTEREN (1 << 2) -#define MEMEN (1 << 1) - -/* PCIAHB_WIN1_CTR and PCIAHB_WIN2_CTR */ -#define PCIAHB_WIN_PREFETCH ((1 << 1)|(1 << 0)) - -/* AHBPCI_WIN1_CTR */ -#define PCIWIN1_PCICMD ((1 << 3)|(1 << 1)) -#define AHB_CFG_AHBPCI 0x40000000 -#define AHB_CFG_HOST 0x80000000 - -/* AHBPCI_WIN2_CTR */ -#define PCIWIN2_PCICMD ((1 << 2)|(1 << 1)) - -/* PCI_INT_ENABLE */ -#define USBH_PMEEN (1 << 19) -#define USBH_INTBEN (1 << 17) -#define USBH_INTAEN (1 << 16) - -/* AHB_BUS_CTR */ -#define SMODE_READY_CTR (1 << 17) -#define SMODE_READ_BURST (1 << 16) -#define MMODE_HBUSREQ (1 << 7) -#define MMODE_BOUNDARY ((1 << 6)|(1 << 5)) -#define MMODE_BURST_WIDTH ((1 << 4)|(1 << 3)) -#define MMODE_SINGLE_MODE ((1 << 4)|(1 << 3)) -#define MMODE_WR_INCR (1 << 2) -#define MMODE_BYTE_BURST (1 << 1) -#define MMODE_HTRANS (1 << 0) - -/* PCI_ARBITER_CTR */ -#define PCIBUS_PARK_TIMER 0x00FF0000 -#define PCIBUS_PARK_TIMER_SET 0x00070000 -#define PCIBP_MODE (1 << 12) -#define PCIREQ7 (1 << 7) -#define PCIREQ6 (1 << 6) -#define PCIREQ5 (1 << 5) -#define PCIREQ4 (1 << 4) -#define PCIREQ3 (1 << 3) -#define PCIREQ2 (1 << 2) -#define PCIREQ1 (1 << 1) -#define PCIREQ0 (1 << 0) - -#define SMSTPCR7 0xE615014C -#define SMSTPCR703 (1 << 3) - -/* Init AHB master and slave functions of the host logic */ -#define AHB_BUS_CTR_INIT \ - (SMODE_READY_CTR | MMODE_HBUSREQ | MMODE_WR_INCR | \ - MMODE_BYTE_BURST | MMODE_HTRANS) - -#define USBCTR_WIN_SIZE_1GB 0x800 - -/* PCI Configuration Registers */ -#define PCI_CONF_OHCI_OFFSET 0x10000 -#define PCI_CONF_EHCI_OFFSET 0x10100 -struct ahb_pciconf { - u32 vid_did; - u32 cmnd_sts; - u32 rev; - u32 cache_line; - u32 basead; -}; - -/* PCI Configuration Registers for AHB-PCI Bridge Registers */ -#define PCI_CONF_AHBPCI_OFFSET 0x10000 -struct ahbconf_pci_bridge { - u32 vid_did; /* 0x00 */ - u32 cmnd_sts; - u32 revid_cc; - u32 cls_lt_ht_bist; - u32 basead; /* 0x10 */ - u32 win1_basead; - u32 win2_basead; - u32 dummy0[5]; - u32 ssvdi_ssid; /* 0x2C */ - u32 dummy1[4]; - u32 intr_line_pin; -}; - -/* AHB-PCI Bridge PCI Communication Registers */ -#define AHBPCI_OFFSET 0x10800 -struct ahbcom_pci_bridge { - u32 pciahb_win1_ctr; /* 0x00 */ - u32 pciahb_win2_ctr; - u32 pciahb_dct_ctr; - u32 dummy0; - u32 ahbpci_win1_ctr; /* 0x10 */ - u32 ahbpci_win2_ctr; - u32 dummy1; - u32 ahbpci_dct_ctr; - u32 pci_int_enable; /* 0x20 */ - u32 pci_int_status; - u32 dummy2[2]; - u32 ahb_bus_ctr; /* 0x30 */ - u32 usbctr; - u32 dummy3[2]; - u32 pci_arbiter_ctr; /* 0x40 */ - u32 dummy4; - u32 pci_unit_rev; /* 0x48 */ -}; - -struct rmobile_ehci_reg { - u32 hciversion; /* hciversion/caplength */ - u32 hcsparams; /* hcsparams */ - u32 hccparams; /* hccparams */ - u32 hcsp_portroute; /* hcsp_portroute */ - u32 usbcmd; /* usbcmd */ - u32 usbsts; /* usbsts */ - u32 usbintr; /* usbintr */ - u32 frindex; /* frindex */ - u32 ctrldssegment; /* ctrldssegment */ - u32 periodiclistbase; /* periodiclistbase */ - u32 asynclistaddr; /* asynclistaddr */ - u32 dummy[9]; - u32 configflag; /* configflag */ - u32 portsc; /* portsc */ -}; - -#endif /* __EHCI_RMOBILE_H__ */ diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index cce78846d98..3d3dd5f279f 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -41,7 +41,6 @@ obj-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o obj-$(CONFIG_USB_EHCI_TEGRA) += ehci-tegra.o obj-$(CONFIG_USB_EHCI_VCT) += ehci-vct.o obj-$(CONFIG_USB_EHCI_VF) += ehci-vf.o -obj-$(CONFIG_USB_EHCI_RMOBILE) += ehci-rmobile.o obj-$(CONFIG_USB_EHCI_ZYNQ) += ehci-zynq.o # xhci diff --git a/drivers/usb/host/ehci-rmobile.c b/drivers/usb/host/ehci-rmobile.c deleted file mode 100644 index 60525f22867..00000000000 --- a/drivers/usb/host/ehci-rmobile.c +++ /dev/null @@ -1,129 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * EHCI HCD (Host Controller Driver) for USB. - * - * Copyright (C) 2013,2014 Renesas Electronics Corporation - * Copyright (C) 2014 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> - */ - -#include <common.h> -#include <asm/io.h> -#include <asm/arch/ehci-rmobile.h> -#include <linux/delay.h> -#include "ehci.h" - -#if defined(CONFIG_R8A7740) -static u32 usb_base_address[] = { - 0xC6700000 -}; -#elif defined(CONFIG_R8A7790) -static u32 usb_base_address[] = { - 0xEE080000, /* USB0 (EHCI) */ - 0xEE0A0000, /* USB1 */ - 0xEE0C0000, /* USB2 */ -}; -#elif defined(CONFIG_R8A7791) || defined(CONFIG_R8A7793) || \ - defined(CONFIG_R8A7794) -static u32 usb_base_address[] = { - 0xEE080000, /* USB0 (EHCI) */ - 0xEE0C0000, /* USB1 */ -}; -#else -#error rmobile EHCI USB driver not supported on this platform -#endif - -int ehci_hcd_stop(int index) -{ - int i; - u32 base; - struct ahbcom_pci_bridge *ahbcom_pci; - - base = usb_base_address[index]; - ahbcom_pci = (struct ahbcom_pci_bridge *)(base + AHBPCI_OFFSET); - writel(0, &ahbcom_pci->ahb_bus_ctr); - - /* reset ehci */ - setbits_le32(base + EHCI_USBCMD, CMD_RESET); - for (i = 100; i > 0; i--) { - if (!(readl(base + EHCI_USBCMD) & CMD_RESET)) - break; - udelay(100); - } - - if (!i) - printf("error : ehci(%d) reset failed.\n", index); - - if (index == (ARRAY_SIZE(usb_base_address) - 1)) - setbits_le32(SMSTPCR7, SMSTPCR703); - - return 0; -} - -int ehci_hcd_init(int index, enum usb_init_type init, - struct ehci_hccr **hccr, struct ehci_hcor **hcor) -{ - u32 base; - u32 phys_base; - struct rmobile_ehci_reg *rehci; - struct ahbcom_pci_bridge *ahbcom_pci; - struct ahbconf_pci_bridge *ahbconf_pci; - struct ahb_pciconf *ahb_pciconf_ohci; - struct ahb_pciconf *ahb_pciconf_ehci; - uint32_t cap_base; - - base = usb_base_address[index]; - phys_base = base; - if (index == 0) - clrbits_le32(SMSTPCR7, SMSTPCR703); - - rehci = (struct rmobile_ehci_reg *)(base + EHCI_OFFSET); - ahbcom_pci = (struct ahbcom_pci_bridge *)(base + AHBPCI_OFFSET); - ahbconf_pci = - (struct ahbconf_pci_bridge *)(base + PCI_CONF_AHBPCI_OFFSET); - ahb_pciconf_ohci = (struct ahb_pciconf *)(base + PCI_CONF_OHCI_OFFSET); - ahb_pciconf_ehci = (struct ahb_pciconf *)(base + PCI_CONF_EHCI_OFFSET); - - /* Clock & Reset & Direct Power Down */ - clrsetbits_le32(&ahbcom_pci->usbctr, - (DIRPD | PCICLK_MASK | USBH_RST), USBCTR_WIN_SIZE_1GB); - clrbits_le32(&ahbcom_pci->usbctr, PLL_RST); - - /* AHB-PCI Bridge Communication Registers */ - writel(AHB_BUS_CTR_INIT, &ahbcom_pci->ahb_bus_ctr); - writel((CFG_SYS_SDRAM_BASE & 0xf0000000) | PCIAHB_WIN_PREFETCH, - &ahbcom_pci->pciahb_win1_ctr); - writel(0xf0000000 | PCIAHB_WIN_PREFETCH, - &ahbcom_pci->pciahb_win2_ctr); - writel(phys_base | PCIWIN2_PCICMD, &ahbcom_pci->ahbpci_win2_ctr); - - setbits_le32(&ahbcom_pci->pci_arbiter_ctr, - PCIBP_MODE | PCIREQ1 | PCIREQ0); - - /* PCI Configuration Registers for AHBPCI */ - writel(PCIWIN1_PCICMD | AHB_CFG_AHBPCI, - &ahbcom_pci->ahbpci_win1_ctr); - writel(phys_base + AHBPCI_OFFSET, &ahbconf_pci->basead); - writel(CFG_SYS_SDRAM_BASE & 0xf0000000, &ahbconf_pci->win1_basead); - writel(0xf0000000, &ahbconf_pci->win2_basead); - writel(SERREN | PERREN | MASTEREN | MEMEN, - &ahbconf_pci->cmnd_sts); - - /* PCI Configuration Registers for EHCI */ - writel(PCIWIN1_PCICMD | AHB_CFG_HOST, &ahbcom_pci->ahbpci_win1_ctr); - writel(phys_base + OHCI_OFFSET, &ahb_pciconf_ohci->basead); - writel(phys_base + EHCI_OFFSET, &ahb_pciconf_ehci->basead); - writel(SERREN | PERREN | MASTEREN | MEMEN, - &ahb_pciconf_ohci->cmnd_sts); - writel(SERREN | PERREN | MASTEREN | MEMEN, - &ahb_pciconf_ehci->cmnd_sts); - - /* Enable PCI interrupt */ - setbits_le32(&ahbcom_pci->pci_int_enable, - USBH_PMEEN | USBH_INTBEN | USBH_INTAEN); - - *hccr = (struct ehci_hccr *)((uint32_t)&rehci->hciversion); - cap_base = ehci_readl(&(*hccr)->cr_capbase); - *hcor = (struct ehci_hcor *)((uint32_t)*hccr + HC_LENGTH(cap_base)); - - return 0; -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 70/76] usb: Drop unused ehci-vct driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (65 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 69/76] rmobile: Drop unused ehci-rmobile driver Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 71/76] usb: Drop unused sl811-hcd driver Simon Glass ` (5 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Marek Vasut This is not used. Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/usb/host/Makefile | 1 - drivers/usb/host/ehci-vct.c | 44 ------------------------------------- 2 files changed, 45 deletions(-) delete mode 100644 drivers/usb/host/ehci-vct.c diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 3d3dd5f279f..3e5ba2bd0ba 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -39,7 +39,6 @@ obj-$(CONFIG_USB_EHCI_MARVELL) += ehci-marvell.o obj-$(CONFIG_USB_EHCI_MSM) += ehci-msm.o obj-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o obj-$(CONFIG_USB_EHCI_TEGRA) += ehci-tegra.o -obj-$(CONFIG_USB_EHCI_VCT) += ehci-vct.o obj-$(CONFIG_USB_EHCI_VF) += ehci-vf.o obj-$(CONFIG_USB_EHCI_ZYNQ) += ehci-zynq.o diff --git a/drivers/usb/host/ehci-vct.c b/drivers/usb/host/ehci-vct.c deleted file mode 100644 index 7167f82b481..00000000000 --- a/drivers/usb/host/ehci-vct.c +++ /dev/null @@ -1,44 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2009 Stefan Roese <sr@denx.de>, DENX Software Engineering - */ - -#include <common.h> -#include <usb.h> - -#include "ehci.h" - -int vct_ehci_hcd_init(u32 *hccr, u32 *hcor); - -/* - * Create the appropriate control structures to manage - * a new EHCI host controller. - */ -int ehci_hcd_init(int index, enum usb_init_type init, - struct ehci_hccr **hccr, struct ehci_hcor **hcor) -{ - int ret; - u32 vct_hccr; - u32 vct_hcor; - - /* - * Init VCT specific stuff - */ - ret = vct_ehci_hcd_init(&vct_hccr, &vct_hcor); - if (ret) - return ret; - - *hccr = (struct ehci_hccr *)vct_hccr; - *hcor = (struct ehci_hcor *)vct_hcor; - - return 0; -} - -/* - * Destroy the appropriate control structures corresponding - * the the EHCI host controller. - */ -int ehci_hcd_stop(int index) -{ - return 0; -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 71/76] usb: Drop unused sl811-hcd driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (66 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 70/76] usb: Drop unused ehci-vct driver Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 72/76] imx: Drop CONFIG_USE_PLUGIN Simon Glass ` (4 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Marek Vasut This is not used. Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) drivers/usb/host/Makefile | 1 - drivers/usb/host/sl811-hcd.c | 714 ----------------------------------- drivers/usb/host/sl811.h | 104 ----- 3 files changed, 819 deletions(-) delete mode 100644 drivers/usb/host/sl811-hcd.c delete mode 100644 drivers/usb/host/sl811.h diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 3e5ba2bd0ba..8dad36f9369 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -17,7 +17,6 @@ obj-$(CONFIG_USB_OHCI_NEW) += ohci-hcd.o obj-$(CONFIG_USB_ATMEL) += ohci-at91.o obj-$(CONFIG_USB_OHCI_DA8XX) += ohci-da8xx.o obj-$(CONFIG_USB_R8A66597_HCD) += r8a66597-hcd.o -obj-$(CONFIG_USB_SL811HS) += sl811-hcd.o obj-$(CONFIG_USB_OHCI_LPC32XX) += ohci-lpc32xx.o obj-$(CONFIG_USB_OHCI_PCI) += ohci-pci.o obj-$(CONFIG_USB_OHCI_GENERIC) += ohci-generic.o diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c deleted file mode 100644 index 7c823f241a8..00000000000 --- a/drivers/usb/host/sl811-hcd.c +++ /dev/null @@ -1,714 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * This code is based on linux driver for sl811hs chip, source at - * drivers/usb/host/sl811.c: - * - * SL811 Host Controller Interface driver for USB. - * - * Copyright (c) 2003/06, Courage Co., Ltd. - * - * Based on: - * 1.uhci.c by Linus Torvalds, Johannes Erdfelt, Randy Dunlap, - * Georg Acher, Deti Fliegl, Thomas Sailer, Roman Weissgaerber, - * Adam Richter, Gregory P. Smith; - * 2.Original SL811 driver (hc_sl811.o) by Pei Liu <pbl@cypress.com> - * 3.Rewrited as sl811.o by Yin Aihua <yinah:couragetech.com.cn> - */ - -#include <common.h> -#include <mpc8xx.h> -#include <usb.h> -#include <linux/delay.h> -#include "sl811.h" - -#include "../../../board/kup/common/kup.h" - -#ifdef __PPC__ -# define EIEIO __asm__ volatile ("eieio") -#else -# define EIEIO /* nothing */ -#endif - -#define SL811_ADR (0x50000000) -#define SL811_DAT (0x50000001) - -#ifdef SL811_DEBUG -static int debug = 9; -#endif - -static int root_hub_devnum = 0; -static struct usb_port_status rh_status = { 0 };/* root hub port status */ - -static int sl811_rh_submit_urb(struct usb_device *usb_dev, unsigned long pipe, - void *data, int buf_len, struct devrequest *cmd); - -static void sl811_write (__u8 index, __u8 data) -{ - *(volatile unsigned char *) (SL811_ADR) = index; - EIEIO; - *(volatile unsigned char *) (SL811_DAT) = data; - EIEIO; -} - -static __u8 sl811_read (__u8 index) -{ - __u8 data; - - *(volatile unsigned char *) (SL811_ADR) = index; - EIEIO; - data = *(volatile unsigned char *) (SL811_DAT); - EIEIO; - return (data); -} - -/* - * Read consecutive bytes of data from the SL811H/SL11H buffer - */ -static void inline sl811_read_buf(__u8 offset, __u8 *buf, __u8 size) -{ - *(volatile unsigned char *) (SL811_ADR) = offset; - EIEIO; - while (size--) { - *buf++ = *(volatile unsigned char *) (SL811_DAT); - EIEIO; - } -} - -/* - * Write consecutive bytes of data to the SL811H/SL11H buffer - */ -static void inline sl811_write_buf(__u8 offset, __u8 *buf, __u8 size) -{ - *(volatile unsigned char *) (SL811_ADR) = offset; - EIEIO; - while (size--) { - *(volatile unsigned char *) (SL811_DAT) = *buf++; - EIEIO; - } -} - -int usb_init_kup4x (void) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile memctl8xx_t *memctl = &immap->im_memctl; - int i; - unsigned char tmp; - - memctl = &immap->im_memctl; - memctl->memc_or7 = 0xFFFF8726; - memctl->memc_br7 = 0x50000401; /* start at 0x50000000 */ - /* BP 14 low = USB ON */ - immap->im_cpm.cp_pbdat &= ~(BP_USB_VCC); - /* PB 14 nomal port */ - immap->im_cpm.cp_pbpar &= ~(BP_USB_VCC); - /* output */ - immap->im_cpm.cp_pbdir |= (BP_USB_VCC); - - puts ("USB: "); - - for (i = 0x10; i < 0xff; i++) { - sl811_write(i, i); - tmp = (sl811_read(i)); - if (tmp != i) { - printf ("SL811 compare error index=0x%02x read=0x%02x\n", i, tmp); - return (-1); - } - } - printf ("SL811 ready\n"); - return (0); -} - -/* - * This function resets SL811HS controller and detects the speed of - * the connecting device - * - * Return: 0 = no device attached; 1 = USB device attached - */ -static int sl811_hc_reset(void) -{ - int status ; - - sl811_write(SL811_CTRL2, SL811_CTL2_HOST | SL811_12M_HI); - sl811_write(SL811_CTRL1, SL811_CTRL1_RESET); - - mdelay(20); - - /* Disable hardware SOF generation, clear all irq status. */ - sl811_write(SL811_CTRL1, 0); - mdelay(2); - sl811_write(SL811_INTRSTS, 0xff); - status = sl811_read(SL811_INTRSTS); - - if (status & SL811_INTR_NOTPRESENT) { - /* Device is not present */ - PDEBUG(0, "Device not present\n"); - rh_status.wPortStatus &= ~(USB_PORT_STAT_CONNECTION | USB_PORT_STAT_ENABLE); - rh_status.wPortChange |= USB_PORT_STAT_C_CONNECTION; - sl811_write(SL811_INTR, SL811_INTR_INSRMV); - return 0; - } - - /* Send SOF to address 0, endpoint 0. */ - sl811_write(SL811_LEN_B, 0); - sl811_write(SL811_PIDEP_B, PIDEP(USB_PID_SOF, 0)); - sl811_write(SL811_DEV_B, 0x00); - sl811_write(SL811_SOFLOW, SL811_12M_LOW); - - if (status & SL811_INTR_SPEED_FULL) { - /* full speed device connect directly to root hub */ - PDEBUG (0, "Full speed Device attached\n"); - - sl811_write(SL811_CTRL1, SL811_CTRL1_RESET); - mdelay(20); - sl811_write(SL811_CTRL2, SL811_CTL2_HOST | SL811_12M_HI); - sl811_write(SL811_CTRL1, SL811_CTRL1_SOF); - - /* start the SOF or EOP */ - sl811_write(SL811_CTRL_B, SL811_USB_CTRL_ARM); - rh_status.wPortStatus |= USB_PORT_STAT_CONNECTION; - rh_status.wPortStatus &= ~USB_PORT_STAT_LOW_SPEED; - mdelay(2); - sl811_write(SL811_INTRSTS, 0xff); - } else { - /* slow speed device connect directly to root-hub */ - PDEBUG(0, "Low speed Device attached\n"); - - sl811_write(SL811_CTRL1, SL811_CTRL1_RESET); - mdelay(20); - sl811_write(SL811_CTRL2, SL811_CTL2_HOST | SL811_CTL2_DSWAP | SL811_12M_HI); - sl811_write(SL811_CTRL1, SL811_CTRL1_SPEED_LOW | SL811_CTRL1_SOF); - - /* start the SOF or EOP */ - sl811_write(SL811_CTRL_B, SL811_USB_CTRL_ARM); - rh_status.wPortStatus |= USB_PORT_STAT_CONNECTION | USB_PORT_STAT_LOW_SPEED; - mdelay(2); - sl811_write(SL811_INTRSTS, 0xff); - } - - rh_status.wPortChange |= USB_PORT_STAT_C_CONNECTION; - sl811_write(SL811_INTR, /*SL811_INTR_INSRMV*/SL811_INTR_DONE_A); - - return 1; -} - -int usb_lowlevel_init(int index, enum usb_init_type init, void **controller) -{ - root_hub_devnum = 0; - sl811_hc_reset(); - return 0; -} - -int usb_lowlevel_stop(int index) -{ - sl811_hc_reset(); - return 0; -} - -static int calc_needed_buswidth(int bytes, int need_preamble) -{ - return !need_preamble ? bytes * 8 + 256 : 8 * 8 * bytes + 2048; -} - -static int sl811_send_packet(struct usb_device *dev, unsigned long pipe, __u8 *buffer, int len) -{ - __u8 ctrl = SL811_USB_CTRL_ARM | SL811_USB_CTRL_ENABLE; - __u16 status = 0; - int err = 0, time_start = get_timer(0); - int need_preamble = !(rh_status.wPortStatus & USB_PORT_STAT_LOW_SPEED) && - (dev->speed == USB_SPEED_LOW); - - if (len > 239) - return -1; - - if (usb_pipeout(pipe)) - ctrl |= SL811_USB_CTRL_DIR_OUT; - if (usb_gettoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe))) - ctrl |= SL811_USB_CTRL_TOGGLE_1; - if (need_preamble) - ctrl |= SL811_USB_CTRL_PREAMBLE; - - sl811_write(SL811_INTRSTS, 0xff); - - while (err < 3) { - sl811_write(SL811_ADDR_A, 0x10); - sl811_write(SL811_LEN_A, len); - if (usb_pipeout(pipe) && len) - sl811_write_buf(0x10, buffer, len); - - if (!(rh_status.wPortStatus & USB_PORT_STAT_LOW_SPEED) && - sl811_read(SL811_SOFCNTDIV)*64 < calc_needed_buswidth(len, need_preamble)) - ctrl |= SL811_USB_CTRL_SOF; - else - ctrl &= ~SL811_USB_CTRL_SOF; - - sl811_write(SL811_CTRL_A, ctrl); - while (!(sl811_read(SL811_INTRSTS) & SL811_INTR_DONE_A)) { - if (5*CONFIG_SYS_HZ < get_timer(time_start)) { - printf("USB transmit timed out\n"); - return -USB_ST_CRC_ERR; - } - } - - sl811_write(SL811_INTRSTS, 0xff); - status = sl811_read(SL811_STS_A); - - if (status & SL811_USB_STS_ACK) { - int remainder = sl811_read(SL811_CNT_A); - if (remainder) { - PDEBUG(0, "usb transfer remainder = %d\n", remainder); - len -= remainder; - } - if (usb_pipein(pipe) && len) - sl811_read_buf(0x10, buffer, len); - return len; - } - - if ((status & SL811_USB_STS_NAK) == SL811_USB_STS_NAK) - continue; - - PDEBUG(0, "usb transfer error %#x\n", (int)status); - err++; - } - - err = 0; - - if (status & SL811_USB_STS_ERROR) - err |= USB_ST_BUF_ERR; - if (status & SL811_USB_STS_TIMEOUT) - err |= USB_ST_CRC_ERR; - if (status & SL811_USB_STS_STALL) - err |= USB_ST_STALLED; - - return -err; -} - -int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer, - int len) -{ - int dir_out = usb_pipeout(pipe); - int ep = usb_pipeendpoint(pipe); - int max = usb_maxpacket(dev, pipe); - int done = 0; - - PDEBUG(7, "dev = %ld pipe = %ld buf = %p size = %d dir_out = %d\n", - usb_pipedevice(pipe), usb_pipeendpoint(pipe), buffer, len, dir_out); - - dev->status = 0; - - sl811_write(SL811_DEV_A, usb_pipedevice(pipe)); - sl811_write(SL811_PIDEP_A, PIDEP(!dir_out ? USB_PID_IN : USB_PID_OUT, ep)); - while (done < len) { - int res = sl811_send_packet(dev, pipe, (__u8*)buffer+done, - max > len - done ? len - done : max); - if (res < 0) { - dev->status = -res; - return res; - } - - if (!dir_out && res < max) /* short packet */ - break; - - done += res; - usb_dotoggle(dev, ep, dir_out); - } - - dev->act_len = done; - - return 0; -} - -int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer, - int len,struct devrequest *setup) -{ - int done = 0; - int devnum = usb_pipedevice(pipe); - int ep = usb_pipeendpoint(pipe); - - dev->status = 0; - - if (devnum == root_hub_devnum) - return sl811_rh_submit_urb(dev, pipe, buffer, len, setup); - - PDEBUG(7, "dev = %d pipe = %ld buf = %p size = %d rt = %#x req = %#x bus = %i\n", - devnum, ep, buffer, len, (int)setup->requesttype, - (int)setup->request, sl811_read(SL811_SOFCNTDIV)*64); - - sl811_write(SL811_DEV_A, devnum); - sl811_write(SL811_PIDEP_A, PIDEP(USB_PID_SETUP, ep)); - /* setup phase */ - usb_settoggle(dev, ep, 1, 0); - if (sl811_send_packet(dev, usb_sndctrlpipe(dev, ep), - (__u8*)setup, sizeof(*setup)) == sizeof(*setup)) { - int dir_in = usb_pipein(pipe); - int max = usb_maxpacket(dev, pipe); - - /* data phase */ - sl811_write(SL811_PIDEP_A, - PIDEP(dir_in ? USB_PID_IN : USB_PID_OUT, ep)); - usb_settoggle(dev, ep, usb_pipeout(pipe), 1); - while (done < len) { - int res = sl811_send_packet(dev, pipe, (__u8*)buffer+done, - max > len - done ? len - done : max); - if (res < 0) { - PDEBUG(0, "status data failed!\n"); - dev->status = -res; - return 0; - } - done += res; - usb_dotoggle(dev, ep, usb_pipeout(pipe)); - if (dir_in && res < max) /* short packet */ - break; - } - - /* status phase */ - sl811_write(SL811_PIDEP_A, - PIDEP(!dir_in ? USB_PID_IN : USB_PID_OUT, ep)); - usb_settoggle(dev, ep, !usb_pipeout(pipe), 1); - if (sl811_send_packet(dev, - !dir_in ? usb_rcvctrlpipe(dev, ep) : - usb_sndctrlpipe(dev, ep), - 0, 0) < 0) { - PDEBUG(0, "status phase failed!\n"); - dev->status = -1; - } - } else { - PDEBUG(0, "setup phase failed!\n"); - dev->status = -1; - } - - dev->act_len = done; - - return done; -} - -int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer, - int len, int interval, bool nonblock) -{ - PDEBUG(0, "dev = %p pipe = %#lx buf = %p size = %d int = %d\n", dev, pipe, - buffer, len, interval); - return -1; -} - -/* - * SL811 Virtual Root Hub - */ - -/* Device descriptor */ -static __u8 sl811_rh_dev_des[] = -{ - 0x12, /* __u8 bLength; */ - 0x01, /* __u8 bDescriptorType; Device */ - 0x10, /* __u16 bcdUSB; v1.1 */ - 0x01, - 0x09, /* __u8 bDeviceClass; HUB_CLASSCODE */ - 0x00, /* __u8 bDeviceSubClass; */ - 0x00, /* __u8 bDeviceProtocol; */ - 0x08, /* __u8 bMaxPacketSize0; 8 Bytes */ - 0x00, /* __u16 idVendor; */ - 0x00, - 0x00, /* __u16 idProduct; */ - 0x00, - 0x00, /* __u16 bcdDevice; */ - 0x00, - 0x00, /* __u8 iManufacturer; */ - 0x02, /* __u8 iProduct; */ - 0x01, /* __u8 iSerialNumber; */ - 0x01 /* __u8 bNumConfigurations; */ -}; - -/* Configuration descriptor */ -static __u8 sl811_rh_config_des[] = -{ - 0x09, /* __u8 bLength; */ - 0x02, /* __u8 bDescriptorType; Configuration */ - 0x19, /* __u16 wTotalLength; */ - 0x00, - 0x01, /* __u8 bNumInterfaces; */ - 0x01, /* __u8 bConfigurationValue; */ - 0x00, /* __u8 iConfiguration; */ - 0x40, /* __u8 bmAttributes; - Bit 7: Bus-powered, 6: Self-powered, 5 Remote-wakwup, - 4..0: resvd */ - 0x00, /* __u8 MaxPower; */ - - /* interface */ - 0x09, /* __u8 if_bLength; */ - 0x04, /* __u8 if_bDescriptorType; Interface */ - 0x00, /* __u8 if_bInterfaceNumber; */ - 0x00, /* __u8 if_bAlternateSetting; */ - 0x01, /* __u8 if_bNumEndpoints; */ - 0x09, /* __u8 if_bInterfaceClass; HUB_CLASSCODE */ - 0x00, /* __u8 if_bInterfaceSubClass; */ - 0x00, /* __u8 if_bInterfaceProtocol; */ - 0x00, /* __u8 if_iInterface; */ - - /* endpoint */ - 0x07, /* __u8 ep_bLength; */ - 0x05, /* __u8 ep_bDescriptorType; Endpoint */ - 0x81, /* __u8 ep_bEndpointAddress; IN Endpoint 1 */ - 0x03, /* __u8 ep_bmAttributes; Interrupt */ - 0x08, /* __u16 ep_wMaxPacketSize; */ - 0x00, - 0xff /* __u8 ep_bInterval; 255 ms */ -}; - -/* root hub class descriptor*/ -static __u8 sl811_rh_hub_des[] = -{ - 0x09, /* __u8 bLength; */ - 0x29, /* __u8 bDescriptorType; Hub-descriptor */ - 0x01, /* __u8 bNbrPorts; */ - 0x00, /* __u16 wHubCharacteristics; */ - 0x00, - 0x50, /* __u8 bPwrOn2pwrGood; 2ms */ - 0x00, /* __u8 bHubContrCurrent; 0 mA */ - 0xfc, /* __u8 DeviceRemovable; *** 7 Ports max *** */ - 0xff /* __u8 PortPwrCtrlMask; *** 7 ports max *** */ -}; - -/* - * helper routine for returning string descriptors in UTF-16LE - * input can actually be ISO-8859-1; ASCII is its 7-bit subset - */ -static int ascii2utf (char *s, u8 *utf, int utfmax) -{ - int retval; - - for (retval = 0; *s && utfmax > 1; utfmax -= 2, retval += 2) { - *utf++ = *s++; - *utf++ = 0; - } - return retval; -} - -/* - * root_hub_string is used by each host controller's root hub code, - * so that they're identified consistently throughout the system. - */ -static int usb_root_hub_string (int id, int serial, char *type, __u8 *data, int len) -{ - char buf [30]; - - /* assert (len > (2 * (sizeof (buf) + 1))); - assert (strlen (type) <= 8);*/ - - /* language ids */ - if (id == 0) { - *data++ = 4; *data++ = 3; /* 4 bytes data */ - *data++ = 0; *data++ = 0; /* some language id */ - return 4; - - /* serial number */ - } else if (id == 1) { - sprintf (buf, "%#x", serial); - - /* product description */ - } else if (id == 2) { - sprintf (buf, "USB %s Root Hub", type); - - /* id 3 == vendor description */ - - /* unsupported IDs --> "stall" */ - } else - return 0; - - ascii2utf (buf, data + 2, len - 2); - data [0] = 2 + strlen(buf) * 2; - data [1] = 3; - return data [0]; -} - -/* helper macro */ -#define OK(x) len = (x); break - -/* - * This function handles all USB request to the the virtual root hub - */ -static int sl811_rh_submit_urb(struct usb_device *usb_dev, unsigned long pipe, - void *data, int buf_len, struct devrequest *cmd) -{ - __u8 data_buf[16]; - __u8 *bufp = data_buf; - int len = 0; - int status = 0; - __u16 bmRType_bReq; - __u16 wValue = le16_to_cpu (cmd->value); - __u16 wLength = le16_to_cpu (cmd->length); -#ifdef SL811_DEBUG - __u16 wIndex = le16_to_cpu (cmd->index); -#endif - - if (usb_pipeint(pipe)) { - PDEBUG(0, "interrupt transfer unimplemented!\n"); - return 0; - } - - bmRType_bReq = cmd->requesttype | (cmd->request << 8); - - PDEBUG(5, "submit rh urb, req = %d(%x) val = %#x index = %#x len=%d\n", - bmRType_bReq, bmRType_bReq, wValue, wIndex, wLength); - - /* Request Destination: - without flags: Device, - USB_RECIP_INTERFACE: interface, - USB_RECIP_ENDPOINT: endpoint, - USB_TYPE_CLASS means HUB here, - USB_RECIP_OTHER | USB_TYPE_CLASS almost ever means HUB_PORT here - */ - switch (bmRType_bReq) { - case RH_GET_STATUS: - *(__u16 *)bufp = cpu_to_le16(1); - OK(2); - - case RH_GET_STATUS | USB_RECIP_INTERFACE: - *(__u16 *)bufp = cpu_to_le16(0); - OK(2); - - case RH_GET_STATUS | USB_RECIP_ENDPOINT: - *(__u16 *)bufp = cpu_to_le16(0); - OK(2); - - case RH_GET_STATUS | USB_TYPE_CLASS: - *(__u32 *)bufp = cpu_to_le32(0); - OK(4); - - case RH_GET_STATUS | USB_RECIP_OTHER | USB_TYPE_CLASS: - *(__u32 *)bufp = cpu_to_le32(rh_status.wPortChange<<16 | rh_status.wPortStatus); - OK(4); - - case RH_CLEAR_FEATURE | USB_RECIP_ENDPOINT: - switch (wValue) { - case 1: - OK(0); - } - break; - - case RH_CLEAR_FEATURE | USB_TYPE_CLASS: - switch (wValue) { - case C_HUB_LOCAL_POWER: - OK(0); - - case C_HUB_OVER_CURRENT: - OK(0); - } - break; - - case RH_CLEAR_FEATURE | USB_RECIP_OTHER | USB_TYPE_CLASS: - switch (wValue) { - case USB_PORT_FEAT_ENABLE: - rh_status.wPortStatus &= ~USB_PORT_STAT_ENABLE; - OK(0); - - case USB_PORT_FEAT_SUSPEND: - rh_status.wPortStatus &= ~USB_PORT_STAT_SUSPEND; - OK(0); - - case USB_PORT_FEAT_POWER: - rh_status.wPortStatus &= ~USB_PORT_STAT_POWER; - OK(0); - - case USB_PORT_FEAT_C_CONNECTION: - rh_status.wPortChange &= ~USB_PORT_STAT_C_CONNECTION; - OK(0); - - case USB_PORT_FEAT_C_ENABLE: - rh_status.wPortChange &= ~USB_PORT_STAT_C_ENABLE; - OK(0); - - case USB_PORT_FEAT_C_SUSPEND: - rh_status.wPortChange &= ~USB_PORT_STAT_C_SUSPEND; - OK(0); - - case USB_PORT_FEAT_C_OVER_CURRENT: - rh_status.wPortChange &= ~USB_PORT_STAT_C_OVERCURRENT; - OK(0); - - case USB_PORT_FEAT_C_RESET: - rh_status.wPortChange &= ~USB_PORT_STAT_C_RESET; - OK(0); - } - break; - - case RH_SET_FEATURE | USB_RECIP_OTHER | USB_TYPE_CLASS: - switch (wValue) { - case USB_PORT_FEAT_SUSPEND: - rh_status.wPortStatus |= USB_PORT_STAT_SUSPEND; - OK(0); - - case USB_PORT_FEAT_RESET: - rh_status.wPortStatus |= USB_PORT_STAT_RESET; - rh_status.wPortChange = 0; - rh_status.wPortChange |= USB_PORT_STAT_C_RESET; - rh_status.wPortStatus &= ~USB_PORT_STAT_RESET; - rh_status.wPortStatus |= USB_PORT_STAT_ENABLE; - OK(0); - - case USB_PORT_FEAT_POWER: - rh_status.wPortStatus |= USB_PORT_STAT_POWER; - OK(0); - - case USB_PORT_FEAT_ENABLE: - rh_status.wPortStatus |= USB_PORT_STAT_ENABLE; - OK(0); - } - break; - - case RH_SET_ADDRESS: - root_hub_devnum = wValue; - OK(0); - - case RH_GET_DESCRIPTOR: - switch ((wValue & 0xff00) >> 8) { - case USB_DT_DEVICE: - len = sizeof(sl811_rh_dev_des); - bufp = sl811_rh_dev_des; - OK(len); - - case USB_DT_CONFIG: - len = sizeof(sl811_rh_config_des); - bufp = sl811_rh_config_des; - OK(len); - - case USB_DT_STRING: - len = usb_root_hub_string(wValue & 0xff, (int)(long)0, "SL811HS", data, wLength); - if (len > 0) { - bufp = data; - OK(len); - } - - default: - status = -32; - } - break; - - case RH_GET_DESCRIPTOR | USB_TYPE_CLASS: - len = sizeof(sl811_rh_hub_des); - bufp = sl811_rh_hub_des; - OK(len); - - case RH_GET_CONFIGURATION: - bufp[0] = 0x01; - OK(1); - - case RH_SET_CONFIGURATION: - OK(0); - - default: - PDEBUG(1, "unsupported root hub command\n"); - status = -32; - } - - len = min(len, buf_len); - if (data != bufp) - memcpy(data, bufp, len); - - PDEBUG(5, "len = %d, status = %d\n", len, status); - - usb_dev->status = status; - usb_dev->act_len = len; - - return status == 0 ? len : status; -} diff --git a/drivers/usb/host/sl811.h b/drivers/usb/host/sl811.h deleted file mode 100644 index c1f9f013bd1..00000000000 --- a/drivers/usb/host/sl811.h +++ /dev/null @@ -1,104 +0,0 @@ -#ifndef __UBOOT_SL811_H -#define __UBOOT_SL811_H - -#undef SL811_DEBUG - -#ifdef SL811_DEBUG - #define PDEBUG(level, fmt, args...) \ - if (debug >= (level)) printf("[%s:%d] " fmt, \ - __PRETTY_FUNCTION__, __LINE__ , ## args) -#else - #define PDEBUG(level, fmt, args...) do {} while(0) -#endif - -/* Sl811 host control register */ -#define SL811_CTRL_A 0x00 -#define SL811_ADDR_A 0x01 -#define SL811_LEN_A 0x02 -#define SL811_STS_A 0x03 /* read */ -#define SL811_PIDEP_A 0x03 /* write */ -#define SL811_CNT_A 0x04 /* read */ -#define SL811_DEV_A 0x04 /* write */ -#define SL811_CTRL1 0x05 -#define SL811_INTR 0x06 -#define SL811_CTRL_B 0x08 -#define SL811_ADDR_B 0x09 -#define SL811_LEN_B 0x0A -#define SL811_STS_B 0x0B /* read */ -#define SL811_PIDEP_B 0x0B /* write */ -#define SL811_CNT_B 0x0C /* read */ -#define SL811_DEV_B 0x0C /* write */ -#define SL811_INTRSTS 0x0D /* write clears bitwise */ -#define SL811_HWREV 0x0E /* read */ -#define SL811_SOFLOW 0x0E /* write */ -#define SL811_SOFCNTDIV 0x0F /* read */ -#define SL811_CTRL2 0x0F /* write */ - -/* USB control register bits (addr 0x00 and addr 0x08) */ -#define SL811_USB_CTRL_ARM 0x01 -#define SL811_USB_CTRL_ENABLE 0x02 -#define SL811_USB_CTRL_DIR_OUT 0x04 -#define SL811_USB_CTRL_ISO 0x10 -#define SL811_USB_CTRL_SOF 0x20 -#define SL811_USB_CTRL_TOGGLE_1 0x40 -#define SL811_USB_CTRL_PREAMBLE 0x80 - -/* USB status register bits (addr 0x03 and addr 0x0B) */ -#define SL811_USB_STS_ACK 0x01 -#define SL811_USB_STS_ERROR 0x02 -#define SL811_USB_STS_TIMEOUT 0x04 -#define SL811_USB_STS_TOGGLE_1 0x08 -#define SL811_USB_STS_SETUP 0x10 -#define SL811_USB_STS_OVERFLOW 0x20 -#define SL811_USB_STS_NAK 0x40 -#define SL811_USB_STS_STALL 0x80 - -/* Control register 1 bits (addr 0x05) */ -#define SL811_CTRL1_SOF 0x01 -#define SL811_CTRL1_RESET 0x08 -#define SL811_CTRL1_JKSTATE 0x10 -#define SL811_CTRL1_SPEED_LOW 0x20 -#define SL811_CTRL1_SUSPEND 0x40 - -/* Interrut enable (addr 0x06) and interrupt status register bits (addr 0x0D) */ -#define SL811_INTR_DONE_A 0x01 -#define SL811_INTR_DONE_B 0x02 -#define SL811_INTR_SOF 0x10 -#define SL811_INTR_INSRMV 0x20 -#define SL811_INTR_DETECT 0x40 -#define SL811_INTR_NOTPRESENT 0x40 -#define SL811_INTR_SPEED_FULL 0x80 /* only in status reg */ - -/* HW rev and SOF lo register bits (addr 0x0E) */ -#define SL811_HWR_HWREV 0xF0 - -/* SOF counter and control reg 2 (addr 0x0F) */ -#define SL811_CTL2_SOFHI 0x3F -#define SL811_CTL2_DSWAP 0x40 -#define SL811_CTL2_HOST 0x80 - -/* Set up for 1-ms SOF time. */ -#define SL811_12M_LOW 0xE0 -#define SL811_12M_HI 0x2E - -#define SL811_DATA_START 0x10 -#define SL811_DATA_LIMIT 240 - -/* Requests: bRequest << 8 | bmRequestType */ -#define RH_GET_STATUS 0x0080 -#define RH_CLEAR_FEATURE 0x0100 -#define RH_SET_FEATURE 0x0300 -#define RH_SET_ADDRESS 0x0500 -#define RH_GET_DESCRIPTOR 0x0680 -#define RH_SET_DESCRIPTOR 0x0700 -#define RH_GET_CONFIGURATION 0x0880 -#define RH_SET_CONFIGURATION 0x0900 -#define RH_GET_STATE 0x0280 -#define RH_GET_INTERFACE 0x0A80 -#define RH_SET_INTERFACE 0x0B00 -#define RH_SYNC_FRAME 0x0C80 - - -#define PIDEP(pid, ep) (((pid) & 0x0f) << 4 | (ep)) - -#endif /* __UBOOT_SL811_H */ -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 72/76] imx: Drop CONFIG_USE_PLUGIN 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (67 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 71/76] usb: Drop unused sl811-hcd driver Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 73/76] freescale: Drop unused vsc3316_3308 driver Simon Glass ` (3 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass, Stefano Babic This option is not defined anywhere. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) board/freescale/mx7ulp_evk/Makefile | 4 ---- 1 file changed, 4 deletions(-) diff --git a/board/freescale/mx7ulp_evk/Makefile b/board/freescale/mx7ulp_evk/Makefile index 686763d6744..9f33c61f03b 100644 --- a/board/freescale/mx7ulp_evk/Makefile +++ b/board/freescale/mx7ulp_evk/Makefile @@ -2,7 +2,3 @@ # (C) Copyright 2016 Freescale Semiconductor, Inc. obj-y := mx7ulp_evk.o - -extra-$(CONFIG_USE_PLUGIN) := plugin.bin -$(obj)/plugin.bin: $(obj)/plugin.o - $(OBJCOPY) -O binary --gap-fill 0xff $< $@ -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 73/76] freescale: Drop unused vsc3316_3308 driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (68 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 72/76] imx: Drop CONFIG_USE_PLUGIN Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 74/76] tools: Drop xway-swap-bytes tool Simon Glass ` (2 subsequent siblings) 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used. Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) board/freescale/common/Makefile | 1 - board/freescale/common/vsc3316_3308.c | 530 -------------------------- 2 files changed, 531 deletions(-) delete mode 100644 board/freescale/common/vsc3316_3308.c diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index 5f0503faf8d..c200cf4d403 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -54,7 +54,6 @@ obj-$(CONFIG_TARGET_MPC8548CDS) += cds_pci_ft.o obj-$(CONFIG_TARGET_P3041DS) += ics307_clk.o obj-$(CONFIG_TARGET_P4080DS) += ics307_clk.o obj-$(CONFIG_TARGET_P5040DS) += ics307_clk.o -obj-$(CONFIG_VSC_CROSSBAR) += vsc3316_3308.o obj-$(CONFIG_ZM7300) += zm7300.o ifeq ($(CONFIG_$(SPL_)POWER_LEGACY),y) obj-$(CONFIG_POWER_PFUZE100) += pfuze.o diff --git a/board/freescale/common/vsc3316_3308.c b/board/freescale/common/vsc3316_3308.c deleted file mode 100644 index c51f3c5aca2..00000000000 --- a/board/freescale/common/vsc3316_3308.c +++ /dev/null @@ -1,530 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - * Copyright 2020 NXP - */ - -#include "vsc3316_3308.h" -#include <log.h> - -#define REVISION_ID_REG 0x7E -#define INTERFACE_MODE_REG 0x79 -#define CURRENT_PAGE_REGISTER 0x7F -#define CONNECTION_CONFIG_PAGE 0x00 -#define INPUT_STATE_REG 0x13 -#define GLOBAL_INPUT_ISE1 0x51 -#define GLOBAL_INPUT_ISE2 0x52 -#define GLOBAL_INPUT_GAIN 0x53 -#define GLOBAL_INPUT_LOS 0x55 -#define GLOBAL_OUTPUT_PE1 0x56 -#define GLOBAL_OUTPUT_PE2 0x57 -#define GLOBAL_OUTPUT_LEVEL 0x58 -#define GLOBAL_OUTPUT_TERMINATION 0x5A -#define GLOBAL_CORE_CNTRL 0x5D -#define OUTPUT_MODE_PAGE 0x23 -#define CORE_CONTROL_PAGE 0x25 -#define CORE_CONFIG_REG 0x75 - -int vsc_if_enable(unsigned int vsc_addr) -{ - u8 data; - - debug("VSC:Configuring VSC at I2C address 0x%2x" - " for 2-wire interface\n", vsc_addr); - - /* enable 2-wire Serial InterFace (I2C) */ - data = 0x02; -#if CONFIG_IS_ENABLED(DM_I2C) - int ret, bus_num = 0; - struct udevice *dev; - - ret = i2c_get_chip_for_busnum(bus_num, vsc_addr, - 1, &dev); - if (ret) { - printf("%s: Cannot find udev for a bus %d\n", __func__, - bus_num); - return ret; - } - - return dm_i2c_write(dev, INTERFACE_MODE_REG, &data, 1); -#else - return i2c_write(vsc_addr, INTERFACE_MODE_REG, 1, &data, 1); -#endif -} - -int vsc3316_config(unsigned int vsc_addr, int8_t con_arr[][2], - unsigned int num_con) -{ - unsigned int i; - u8 rev_id = 0; - int ret; - - debug("VSC:Initializing VSC3316 at I2C address 0x%2x" - " for Tx\n", vsc_addr); - -#if CONFIG_IS_ENABLED(DM_I2C) - int bus_num = 0; - struct udevice *dev; - - ret = i2c_get_chip_for_busnum(bus_num, vsc_addr, - 1, &dev); - if (ret) { - printf("%s: Cannot find udev for a bus %d\n", __func__, - bus_num); - return ret; - } - - ret = dm_i2c_read(dev, REVISION_ID_REG, &rev_id, 1); - if (ret < 0) { - printf("VSC:0x%x could not read REV_ID from device.\n", - vsc_addr); - return ret; - } - - if (rev_id != 0xab) { - printf("VSC: device at address 0x%x is not VSC3316/3308.\n", - vsc_addr); - return -ENODEV; - } - - ret = vsc_if_enable(vsc_addr); - if (ret) { - printf("VSC:0x%x could not configured for 2-wire I/F.\n", - vsc_addr); - return ret; - } - - /* config connections - page 0x00 */ - dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE); - - /* Making crosspoint connections, by connecting required - * input to output - */ - for (i = 0; i < num_con ; i++) - dm_i2c_reg_write(dev, con_arr[i][1], con_arr[i][0]); - - /* input state - page 0x13 */ - dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, INPUT_STATE_REG); - /* Configuring the required input of the switch */ - for (i = 0; i < num_con ; i++) - dm_i2c_reg_write(dev, con_arr[i][0], 0x80); - - /* Setting Global Input LOS threshold value */ - dm_i2c_reg_write(dev, GLOBAL_INPUT_LOS, 0x60); - - /* config output mode - page 0x23 */ - dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE); - /* Turn ON the Output driver correspond to required output*/ - for (i = 0; i < num_con ; i++) - dm_i2c_reg_write(dev, con_arr[i][1], 0); - - /* configure global core control register, Turn on Global core power */ - dm_i2c_reg_write(dev, GLOBAL_CORE_CNTRL, 0); - -#else - ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1); - if (ret < 0) { - printf("VSC:0x%x could not read REV_ID from device.\n", - vsc_addr); - return ret; - } - - if (rev_id != 0xab) { - printf("VSC: device at address 0x%x is not VSC3316/3308.\n", - vsc_addr); - return -ENODEV; - } - - ret = vsc_if_enable(vsc_addr); - if (ret) { - printf("VSC:0x%x could not configured for 2-wire I/F.\n", - vsc_addr); - return ret; - } - - /* config connections - page 0x00 */ - i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE); - - /* Making crosspoint connections, by connecting required - * input to output */ - for (i = 0; i < num_con ; i++) - i2c_reg_write(vsc_addr, con_arr[i][1], con_arr[i][0]); - - /* input state - page 0x13 */ - i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, INPUT_STATE_REG); - /* Configuring the required input of the switch */ - for (i = 0; i < num_con ; i++) - i2c_reg_write(vsc_addr, con_arr[i][0], 0x80); - - /* Setting Global Input LOS threshold value */ - i2c_reg_write(vsc_addr, GLOBAL_INPUT_LOS, 0x60); - - /* config output mode - page 0x23 */ - i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE); - /* Turn ON the Output driver correspond to required output*/ - for (i = 0; i < num_con ; i++) - i2c_reg_write(vsc_addr, con_arr[i][1], 0); - - /* configure global core control register, Turn on Global core power */ - i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0); -#endif - - vsc_wp_config(vsc_addr); - - return 0; -} - -#ifdef CONFIG_SYS_FSL_B4860QDS_XFI_ERR -int vsc3308_config_adjust(unsigned int vsc_addr, const int8_t con_arr[][2], - unsigned int num_con) -{ - unsigned int i; - u8 rev_id = 0; - int ret; - - debug("VSC:Initializing VSC3308 at I2C address 0x%x for Tx\n", - vsc_addr); - -#if CONFIG_IS_ENABLED(DM_I2C) - int bus_num = 0; - struct udevice *dev; - - ret = i2c_get_chip_for_busnum(bus_num, vsc_addr, - 1, &dev); - if (ret) { - printf("%s: Cannot find udev for a bus %d\n", __func__, - bus_num); - return ret; - } - - ret = dm_i2c_read(dev, REVISION_ID_REG, &rev_id, 1); - if (ret < 0) { - printf("VSC:0x%x could not read REV_ID from device.\n", - vsc_addr); - return ret; - } - - if (rev_id != 0xab) { - printf("VSC: device at address 0x%x is not VSC3316/3308.\n", - vsc_addr); - return -ENODEV; - } - - ret = vsc_if_enable(vsc_addr); - if (ret) { - printf("VSC:0x%x could not configured for 2-wire I/F.\n", - vsc_addr); - return ret; - } - - /* config connections - page 0x00 */ - dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE); - - /* Configure Global Input ISE */ - dm_i2c_reg_write(dev, GLOBAL_INPUT_ISE1, 0); - dm_i2c_reg_write(dev, GLOBAL_INPUT_ISE2, 0); - - /* Configure Tx/Rx Global Output PE1 */ - dm_i2c_reg_write(dev, GLOBAL_OUTPUT_PE1, 0); - - /* Configure Tx/Rx Global Output PE2 */ - dm_i2c_reg_write(dev, GLOBAL_OUTPUT_PE2, 0); - - /* Configure Tx/Rx Global Input GAIN */ - dm_i2c_reg_write(dev, GLOBAL_INPUT_GAIN, 0x3F); - - /* Setting Global Input LOS threshold value */ - dm_i2c_reg_write(dev, GLOBAL_INPUT_LOS, 0xE0); - - /* Setting Global output termination */ - dm_i2c_reg_write(dev, GLOBAL_OUTPUT_TERMINATION, 0); - - /* Configure Tx/Rx Global Output level */ - if (vsc_addr == VSC3308_TX_ADDRESS) - dm_i2c_reg_write(dev, GLOBAL_OUTPUT_LEVEL, 4); - else - dm_i2c_reg_write(dev, GLOBAL_OUTPUT_LEVEL, 2); - - /* Making crosspoint connections, by connecting required - * input to output - */ - for (i = 0; i < num_con ; i++) - dm_i2c_reg_write(dev, con_arr[i][1], con_arr[i][0]); - - /* input state - page 0x13 */ - dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, INPUT_STATE_REG); - /* Turning off all the required input of the switch */ - for (i = 0; i < num_con; i++) - dm_i2c_reg_write(dev, con_arr[i][0], 1); - - /* only turn on specific Tx/Rx requested by the XFI erratum */ - if (vsc_addr == VSC3308_TX_ADDRESS) { - dm_i2c_reg_write(dev, 2, 0); - dm_i2c_reg_write(dev, 3, 0); - } else { - dm_i2c_reg_write(dev, 0, 0); - dm_i2c_reg_write(dev, 1, 0); - } - - /* config output mode - page 0x23 */ - dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE); - /* Turn off the Output driver correspond to required output*/ - for (i = 0; i < num_con ; i++) - dm_i2c_reg_write(dev, con_arr[i][1], 1); - - /* only turn on specific Tx/Rx requested by the XFI erratum */ - if (vsc_addr == VSC3308_TX_ADDRESS) { - dm_i2c_reg_write(dev, 0, 0); - dm_i2c_reg_write(dev, 1, 0); - } else { - dm_i2c_reg_write(dev, 3, 0); - dm_i2c_reg_write(dev, 4, 0); - } - - /* configure global core control register, Turn on Global core power */ - dm_i2c_reg_write(dev, GLOBAL_CORE_CNTRL, 0); -#else - ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1); - if (ret < 0) { - printf("VSC:0x%x could not read REV_ID from device.\n", - vsc_addr); - return ret; - } - - if (rev_id != 0xab) { - printf("VSC: device at address 0x%x is not VSC3316/3308.\n", - vsc_addr); - return -ENODEV; - } - - ret = vsc_if_enable(vsc_addr); - if (ret) { - printf("VSC:0x%x could not configured for 2-wire I/F.\n", - vsc_addr); - return ret; - } - - /* config connections - page 0x00 */ - i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE); - - /* Configure Global Input ISE */ - i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE1, 0); - i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE2, 0); - - /* Configure Tx/Rx Global Output PE1 */ - i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_PE1, 0); - - /* Configure Tx/Rx Global Output PE2 */ - i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_PE2, 0); - - /* Configure Tx/Rx Global Input GAIN */ - i2c_reg_write(vsc_addr, GLOBAL_INPUT_GAIN, 0x3F); - - /* Setting Global Input LOS threshold value */ - i2c_reg_write(vsc_addr, GLOBAL_INPUT_LOS, 0xE0); - - /* Setting Global output termination */ - i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_TERMINATION, 0); - - /* Configure Tx/Rx Global Output level */ - if (vsc_addr == VSC3308_TX_ADDRESS) - i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_LEVEL, 4); - else - i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_LEVEL, 2); - - /* Making crosspoint connections, by connecting required - * input to output */ - for (i = 0; i < num_con ; i++) - i2c_reg_write(vsc_addr, con_arr[i][1], con_arr[i][0]); - - /* input state - page 0x13 */ - i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, INPUT_STATE_REG); - /* Turning off all the required input of the switch */ - for (i = 0; i < num_con; i++) - i2c_reg_write(vsc_addr, con_arr[i][0], 1); - - /* only turn on specific Tx/Rx requested by the XFI erratum */ - if (vsc_addr == VSC3308_TX_ADDRESS) { - i2c_reg_write(vsc_addr, 2, 0); - i2c_reg_write(vsc_addr, 3, 0); - } else { - i2c_reg_write(vsc_addr, 0, 0); - i2c_reg_write(vsc_addr, 1, 0); - } - - /* config output mode - page 0x23 */ - i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE); - /* Turn off the Output driver correspond to required output*/ - for (i = 0; i < num_con ; i++) - i2c_reg_write(vsc_addr, con_arr[i][1], 1); - - /* only turn on specific Tx/Rx requested by the XFI erratum */ - if (vsc_addr == VSC3308_TX_ADDRESS) { - i2c_reg_write(vsc_addr, 0, 0); - i2c_reg_write(vsc_addr, 1, 0); - } else { - i2c_reg_write(vsc_addr, 3, 0); - i2c_reg_write(vsc_addr, 4, 0); - } - - /* configure global core control register, Turn on Global core power */ - i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0); -#endif - vsc_wp_config(vsc_addr); - - return 0; -} -#endif - -int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2], - unsigned int num_con) -{ - unsigned int i; - u8 rev_id = 0; - int ret; - - debug("VSC:Initializing VSC3308 at I2C address 0x%x" - " for Tx\n", vsc_addr); -#if CONFIG_IS_ENABLED(DM_I2C) - int bus_num = 0; - struct udevice *dev; - - ret = i2c_get_chip_for_busnum(bus_num, vsc_addr, - 1, &dev); - if (ret) { - printf("%s: Cannot find udev for a bus %d\n", __func__, - bus_num); - return ret; - } - - ret = dm_i2c_read(dev, REVISION_ID_REG, &rev_id, 1); - if (ret < 0) { - printf("VSC:0x%x could not read REV_ID from device.\n", - vsc_addr); - return ret; - } - - if (rev_id != 0xab) { - printf("VSC: device at address 0x%x is not VSC3316/3308.\n", - vsc_addr); - return -ENODEV; - } - - ret = vsc_if_enable(vsc_addr); - if (ret) { - printf("VSC:0x%x could not configured for 2-wire I/F.\n", - vsc_addr); - return ret; - } - - /* config connections - page 0x00 */ - dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE); - - /* Making crosspoint connections, by connecting required - * input to output - */ - for (i = 0; i < num_con ; i++) - dm_i2c_reg_write(dev, con_arr[i][1], con_arr[i][0]); - - /*Configure Global Input ISE and gain */ - dm_i2c_reg_write(dev, GLOBAL_INPUT_ISE1, 0x12); - dm_i2c_reg_write(dev, GLOBAL_INPUT_ISE2, 0x12); - - /* input state - page 0x13 */ - dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, INPUT_STATE_REG); - /* Turning ON the required input of the switch */ - for (i = 0; i < num_con ; i++) - dm_i2c_reg_write(dev, con_arr[i][0], 0); - - /* Setting Global Input LOS threshold value */ - dm_i2c_reg_write(dev, GLOBAL_INPUT_LOS, 0x60); - - /* config output mode - page 0x23 */ - dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE); - /* Turn ON the Output driver correspond to required output*/ - for (i = 0; i < num_con ; i++) - dm_i2c_reg_write(dev, con_arr[i][1], 0); - - /* configure global core control register, Turn on Global core power */ - dm_i2c_reg_write(dev, GLOBAL_CORE_CNTRL, 0); -#else - ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1); - if (ret < 0) { - printf("VSC:0x%x could not read REV_ID from device.\n", - vsc_addr); - return ret; - } - - if (rev_id != 0xab) { - printf("VSC: device at address 0x%x is not VSC3316/3308.\n", - vsc_addr); - return -ENODEV; - } - - ret = vsc_if_enable(vsc_addr); - if (ret) { - printf("VSC:0x%x could not configured for 2-wire I/F.\n", - vsc_addr); - return ret; - } - - /* config connections - page 0x00 */ - i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE); - - /* Making crosspoint connections, by connecting required - * input to output */ - for (i = 0; i < num_con ; i++) - i2c_reg_write(vsc_addr, con_arr[i][1], con_arr[i][0]); - - /*Configure Global Input ISE and gain */ - i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE1, 0x12); - i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE2, 0x12); - - /* input state - page 0x13 */ - i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, INPUT_STATE_REG); - /* Turning ON the required input of the switch */ - for (i = 0; i < num_con ; i++) - i2c_reg_write(vsc_addr, con_arr[i][0], 0); - - /* Setting Global Input LOS threshold value */ - i2c_reg_write(vsc_addr, GLOBAL_INPUT_LOS, 0x60); - - /* config output mode - page 0x23 */ - i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE); - /* Turn ON the Output driver correspond to required output*/ - for (i = 0; i < num_con ; i++) - i2c_reg_write(vsc_addr, con_arr[i][1], 0); - - /* configure global core control register, Turn on Global core power */ - i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0); -#endif - vsc_wp_config(vsc_addr); - - return 0; -} - -void vsc_wp_config(unsigned int vsc_addr) -{ - debug("VSC:Configuring VSC at address:0x%x for WP\n", vsc_addr); - - /* For new crosspoint configuration to occur, WP bit of - * CORE_CONFIG_REG should be set 1 and then reset to 0 */ -#if CONFIG_IS_ENABLED(DM_I2C) - int ret, bus_num = 0; - struct udevice *dev; - - ret = i2c_get_chip_for_busnum(bus_num, vsc_addr, - 1, &dev); - if (ret) { - printf("%s: Cannot find udev for a bus %d\n", __func__, - bus_num); - return; - } - - dm_i2c_reg_write(dev, CORE_CONFIG_REG, 0x01); - dm_i2c_reg_write(dev, CORE_CONFIG_REG, 0x0); -#else - i2c_reg_write(vsc_addr, CORE_CONFIG_REG, 0x01); - i2c_reg_write(vsc_addr, CORE_CONFIG_REG, 0x0); -#endif -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 74/76] tools: Drop xway-swap-bytes tool 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (69 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 73/76] freescale: Drop unused vsc3316_3308 driver Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 75/76] freescale: Drop unused zm7300 driver Simon Glass 2023-02-01 20:20 ` [PATCH v3 76/76] fdt: Drop use of non-existent OF_PLATDATA option Simon Glass 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is very old and does not appear to be used. The CONFIG option enabling it is no-longer present. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) README | 7 ------- tools/Makefile | 4 ---- tools/xway-swap-bytes.c | 38 -------------------------------------- 3 files changed, 49 deletions(-) delete mode 100644 tools/xway-swap-bytes.c diff --git a/README b/README index edce7890c0f..dee0332b0a8 100644 --- a/README +++ b/README @@ -286,13 +286,6 @@ The following options need to be configured: same as CFG_SYS_DDR_SDRAM_BASE for all Power SoCs. But it could be different for ARM SoCs. -- MIPS CPU options: - CONFIG_XWAY_SWAP_BYTES - - Enable compilation of tools/xway-swap-bytes needed for Lantiq - XWAY SoCs for booting from NOR flash. The U-Boot image needs to - be swapped if a flash programmer is used. - - ARM options: CFG_SYS_EXCEPTION_VECTORS_HIGH diff --git a/tools/Makefile b/tools/Makefile index 0eadd8154a7..041c437e65b 100644 --- a/tools/Makefile +++ b/tools/Makefile @@ -27,7 +27,6 @@ ifneq ($(HOST_TOOLS_ALL),) CONFIG_ARCH_KIRKWOOD = y CONFIG_CMD_LOADS = y CONFIG_CMD_NET = y -CONFIG_XWAY_SWAP_BYTES = y CONFIG_NETCONSOLE = y CONFIG_ARCH_SUNXI = y endif @@ -61,9 +60,6 @@ HOSTCFLAGS_gen_ethaddr_crc.o := -pedantic hostprogs-$(CONFIG_CMD_LOADS) += img2srec HOSTCFLAGS_img2srec.o := -pedantic -hostprogs-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes -HOSTCFLAGS_xway-swap-bytes.o := -pedantic - hostprogs-y += mkenvimage mkenvimage-objs := mkenvimage.o os_support.o lib/crc32.o diff --git a/tools/xway-swap-bytes.c b/tools/xway-swap-bytes.c deleted file mode 100644 index 3a6d82d54a0..00000000000 --- a/tools/xway-swap-bytes.c +++ /dev/null @@ -1,38 +0,0 @@ -#include <stdio.h> -#include <stdlib.h> -#include <string.h> -#include <unistd.h> - -#ifndef BUFSIZ -# define BUFSIZ 4096 -#endif - -#undef BUFSIZ -# define BUFSIZ 64 -int main (void) -{ - short ibuff[BUFSIZ], obuff[BUFSIZ]; - int rc, i, len; - - while ((rc = read (0, ibuff, sizeof (ibuff))) > 0) { - memset (obuff, 0, sizeof (obuff)); - for (i = 0; i < (rc + 1) / 2; i++) { - obuff[i] = ibuff[i ^ 1]; - } - - len = (rc + 1) & ~1; - - if (write (1, obuff, len) != len) { - perror ("read error"); - return (EXIT_FAILURE); - } - - memset (ibuff, 0, sizeof (ibuff)); - } - - if (rc < 0) { - perror ("read error"); - return (EXIT_FAILURE); - } - return (EXIT_SUCCESS); -} -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 75/76] freescale: Drop unused zm7300 driver 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (70 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 74/76] tools: Drop xway-swap-bytes tool Simon Glass @ 2023-02-01 20:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 76/76] fdt: Drop use of non-existent OF_PLATDATA option Simon Glass 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass This is not used anymore. Drop the driver and Kconfig option. Signed-off-by: Simon Glass <sjg@chromium.org> --- (no changes since v1) board/freescale/common/Makefile | 1 - board/freescale/common/zm7300.c | 232 -------------------------------- board/freescale/common/zm7300.h | 21 --- 3 files changed, 254 deletions(-) delete mode 100644 board/freescale/common/zm7300.c delete mode 100644 board/freescale/common/zm7300.h diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index c200cf4d403..b4faf6f9e0a 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -54,7 +54,6 @@ obj-$(CONFIG_TARGET_MPC8548CDS) += cds_pci_ft.o obj-$(CONFIG_TARGET_P3041DS) += ics307_clk.o obj-$(CONFIG_TARGET_P4080DS) += ics307_clk.o obj-$(CONFIG_TARGET_P5040DS) += ics307_clk.o -obj-$(CONFIG_ZM7300) += zm7300.o ifeq ($(CONFIG_$(SPL_)POWER_LEGACY),y) obj-$(CONFIG_POWER_PFUZE100) += pfuze.o endif diff --git a/board/freescale/common/zm7300.c b/board/freescale/common/zm7300.c deleted file mode 100644 index e8c2fc85c84..00000000000 --- a/board/freescale/common/zm7300.c +++ /dev/null @@ -1,232 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2013 Freescale Semiconductor, Inc. - */ - -/* Power-One ZM7300 DPM */ -#include "zm7300.h" -#include <log.h> - -#define DPM_WP 0x96 -#define WRP_OPCODE 0x01 -#define WRM_OPCODE 0x02 -#define RRP_OPCODE 0x11 - -#define DPM_SUCCESS 0x01 -#define DPM_EXEC_FAIL 0x00 - -static const uint16_t hex_to_1_10mv[] = { - 5000, - 5125, - 5250, - 5375, - 5500, - 5625, - 5750, - 5875, - 6000, - 6125, - 6250, - 6375, - 6500, - 6625, - 6750, - 6875, - 7000, - 7125, - 7250, - 7375, - 7500, - 7625, - 7750, - 7875, - 8000, - 8125, - 8250, - 8375, - 8500, - 8625, - 8750, - 8875, - 9000, - 9125, - 9250, - 9375, - 9500, /* 0.95mV */ - 9625, - 9750, - 9875, - 10000, /* 1.0V */ - 10125, - 10250, - 10375, - 10500, - 10625, - 10750, - 10875, - 11000, - 11125, - 11250, - 11375, - 11500, - 11625, - 11750, - 11875, - 12000, - 12125, - 12250, - 12375, - 0, /* reserved */ -}; - - -/* Read Data d from Register r of POL p */ -u8 dpm_rrp(uchar r) -{ - u8 ret[5]; - - ret[0] = RRP_OPCODE; - /* POL is 0 */ - ret[1] = 0; - ret[2] = r; - i2c_read(I2C_DPM_ADDR, 0, -3, ret, 2); - if (ret[1] == DPM_SUCCESS) { /* the DPM returned success as status */ - debug("RRP_OPCODE returned success data is %x\n", ret[0]); - return ret[0]; - } else { - return -1; - } -} - -/* Write Data d into DPM register r (RAM) */ -int dpm_wrm(u8 r, u8 d) -{ - u8 ret[5]; - - ret[0] = WRM_OPCODE; - ret[1] = r; - ret[2] = d; - i2c_read(I2C_DPM_ADDR, 0, -3, ret, 1); - if (ret[0] == DPM_SUCCESS) { /* the DPM returned success as status */ - debug("WRM_OPCODE returned success data is %x\n", ret[0]); - return ret[0]; - } else { - return -1; - } -} - -/* Write Data d into Register r of POL(s) a */ -int dpm_wrp(u8 r, u8 d) -{ - u8 ret[7]; - - ret[0] = WRP_OPCODE; - /* only POL0 is present */ - ret[1] = 0x01; - ret[2] = 0x00; - ret[3] = 0x00; - ret[4] = 0x00; - ret[5] = r; - ret[6] = d; - i2c_read(I2C_DPM_ADDR, 0, -7, ret, 1); - if (ret[0] == DPM_SUCCESS) { /* the DPM returned success as status */ - debug("WRP_OPCODE returned success data is %x\n", ret[0]); - return 0; - } else { - return -1; - } -} - -/* Uses the DPM command RRP */ -u8 zm_read(uchar reg) -{ - return dpm_rrp(reg); -} - -/* ZM_write -- - Steps: - a. Write data to the register - b. Read data from register and compare to written value - c. Return return_code & voltage_read -*/ -u8 zm_write(u8 reg, u8 data) -{ - u8 d; - - /* write data to register */ - dpm_wrp(reg, data); - - /* read register and compare to written value */ - d = dpm_rrp(reg); - if (d != data) { - printf("zm_write : Comparison register data failed\n"); - return -1; - } - - return d; -} - -/* zm_write_out_voltage - * voltage in 1/10 mV - */ -int zm_write_voltage(int voltage) -{ - u8 reg = 0x7, vid; - uint16_t voltage_read; - u8 ret; - - vid = (voltage - 5000) / ZM_STEP; - - ret = zm_write(reg, vid); - if (ret != -1) { - voltage_read = hex_to_1_10mv[ret]; - debug("voltage set to %dmV\n", voltage_read/10); - return voltage_read; - } - return -1; -} - -/* zm_read_out_voltage - * voltage in 1/10 mV - */ -int zm_read_voltage(void) -{ - u8 reg = 0x7; - u8 ret; - int voltage; - - ret = zm_read(reg); - if (ret != -1) { - voltage = hex_to_1_10mv[ret]; - debug("Voltage read is %dmV\n", voltage/10); - return voltage; - } else { - return -1; - } -} - -int zm_disable_wp() -{ - u8 new_wp_value; - - /* Disable using Write-Protect register 0x96 */ - new_wp_value = 0x8; - if ((dpm_wrm(DPM_WP, new_wp_value)) < 0) { - printf("Disable Write-Protect register failed\n"); - return -1; - } - return 0; -} - -int zm_enable_wp() -{ - u8 orig_wp_value; - orig_wp_value = 0x0; - - /* Enable using Write-Protect register 0x96 */ - if ((dpm_wrm(DPM_WP, orig_wp_value)) < 0) { - printf("Enable Write-Protect register failed\n"); - return -1; - } - return 0; -} diff --git a/board/freescale/common/zm7300.h b/board/freescale/common/zm7300.h deleted file mode 100644 index 9ce24afc178..00000000000 --- a/board/freescale/common/zm7300.h +++ /dev/null @@ -1,21 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2013 Freescale Semiconductor, Inc. - */ - -#ifndef __ZM7300_H_ -#define __ZM7300_H 1_ - -#include <common.h> -#include <i2c.h> -#include <errno.h> -#include <asm/io.h> - -#define ZM_STEP 125 -int zm7300_set_voltage(int voltage_1_10mv); -int zm_write_voltage(int voltage); -int zm_read_voltage(void); -int zm_disable_wp(void); -int zm_enable_wp(void); - -#endif /* __ZM7300_H_ */ -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
* [PATCH v3 76/76] fdt: Drop use of non-existent OF_PLATDATA option 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass ` (71 preceding siblings ...) 2023-02-01 20:20 ` [PATCH v3 75/76] freescale: Drop unused zm7300 driver Simon Glass @ 2023-02-01 20:20 ` Simon Glass 72 siblings, 0 replies; 87+ messages in thread From: Simon Glass @ 2023-02-01 20:20 UTC (permalink / raw) To: u-boot; +Cc: Tom Rini, Simon Glass These are only present in SPL. Drop the references to non-SPL versions. Signed-off-by: Simon Glass <sjg@chromium.org> --- Changes in v3: - Drop the 10 patches that rename lower-case Kconfig options Changes in v2: - Drop patch "treewide: Correct invalid Kconfig syntax and warnings" dts/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/dts/Kconfig b/dts/Kconfig index bc5f22029ff..44cc6bf1f6f 100644 --- a/dts/Kconfig +++ b/dts/Kconfig @@ -21,8 +21,8 @@ menu "Device Tree Control" config OF_CONTROL bool "Run-time configuration via Device Tree" - select OF_LIBFDT if !OF_PLATDATA - select OF_REAL if !OF_PLATDATA + select OF_LIBFDT + select OF_REAL help This feature provides for run-time configuration of U-Boot via a flattened device tree. -- 2.39.1.456.gfc5497dd1b-goog ^ permalink raw reply related [flat|nested] 87+ messages in thread
end of thread, other threads:[~2023-02-22 21:24 UTC | newest] Thread overview: 87+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2023-02-01 20:19 [PATCH v3 00/76] Clean up of bad Kconfig options Simon Glass 2023-02-01 20:19 ` [PATCH v3 01/76] moveconfig: Add an option to compare Kconfig against source Simon Glass 2023-02-08 1:37 ` Tom Rini 2023-02-08 18:28 ` Simon Glass 2023-02-08 18:35 ` Tom Rini 2023-02-08 19:06 ` Simon Glass 2023-02-01 20:19 ` [PATCH v3 02/76] power: Drop fg_max77693 Simon Glass 2023-02-01 20:19 ` [PATCH v3 03/76] nand: Drop CONFIG_NAND_SPEAR Simon Glass 2023-02-01 20:19 ` [PATCH v3 04/76] power: Drop pmic_max77693.c Simon Glass 2023-02-01 20:19 ` [PATCH v3 05/76] gpio: Drop adi_gpio2 Simon Glass 2023-02-01 20:19 ` [PATCH v3 06/76] Makefile: Drop CONFIG_AIS_CONFIG_FILE Simon Glass 2023-02-01 20:19 ` [PATCH v3 07/76] misc: Drop ali512x Simon Glass 2023-02-01 20:19 ` [PATCH v3 08/76] sandbox: Drop reference to CONFIG_ARCH_DEVICE_TREE Simon Glass 2023-02-01 20:19 ` [PATCH v3 09/76] arm: mvebu: Remove reference to ARMADA_370 Simon Glass 2023-02-01 20:19 ` [PATCH v3 10/76] arm: mvebu: Drop reference to CONFIG_ARMADA_39X Simon Glass 2023-02-01 20:19 ` [PATCH v3 11/76] ppc: Drop bat_rw Simon Glass 2023-02-01 20:19 ` [PATCH v3 12/76] rockchip: Correct a reference to CONFIG_BOOT_MODE_REG Simon Glass 2023-02-01 20:19 ` [PATCH v3 13/76] cmd: Add an option to enable the ini command Simon Glass 2023-02-01 20:19 ` [PATCH v3 14/76] cmd: Drop mfsl command Simon Glass 2023-02-01 20:19 ` [PATCH v3 15/76] Correct CONFIG_CONTROLCENTERDC Simon Glass 2023-02-01 20:19 ` [PATCH v3 16/76] Drop dataflash_mmc_mux command Simon Glass 2023-02-06 0:29 ` Jaehoon Chung 2023-02-01 20:19 ` [PATCH v3 17/76] Drop CONFIG_DM644X_GPIO Simon Glass 2023-02-01 20:19 ` [PATCH v3 18/76] Makefile: Avoid use of invalid CONFIG_ option Simon Glass 2023-02-01 20:19 ` [PATCH v3 19/76] env: Drop ENV_IS_IN_SATA Simon Glass 2023-02-01 20:19 ` [PATCH v3 20/76] samsung: Drop CONFIG_EXYNOS_PWM_BL Simon Glass 2023-02-03 6:05 ` Minkyu Kang 2023-02-01 20:19 ` [PATCH v3 21/76] fpga: Add a LATTICE option Simon Glass 2023-02-01 20:19 ` [PATCH v3 22/76] fpga: Add a FPGA_STRATIX_II option Simon Glass 2023-02-01 20:19 ` [PATCH v3 23/76] misc: Drop mc9sdz60 driver Simon Glass 2023-02-01 20:19 ` [PATCH v3 24/76] freescale: Drop unused pixis code Simon Glass 2023-02-01 20:19 ` [PATCH v3 25/76] freescale: Drop unused ftpmu010 driver Simon Glass 2023-02-01 20:19 ` [PATCH v3 26/76] rcar: Drop timer Simon Glass 2023-02-01 20:19 ` [PATCH v3 27/76] imx: Drop unused CONFIG_IMX Simon Glass 2023-02-01 20:19 ` [PATCH v3 28/76] arm: Drop old kona code Simon Glass 2023-02-01 20:19 ` [PATCH v3 29/76] video: Drop unused lg4573 driver Simon Glass 2023-02-01 20:19 ` [PATCH v3 30/76] m68k: Drop unused CONFIG_M52277 Simon Glass 2023-02-01 20:19 ` [PATCH v3 31/76] m68k: Drop unused CONFIG_MACH_DAVINCI_DA830_EVM Simon Glass 2023-02-01 20:19 ` [PATCH v3 32/76] arm: Drop CONFIG_MMU Simon Glass 2023-02-01 20:19 ` [PATCH v3 33/76] arc: " Simon Glass 2023-02-01 20:19 ` [PATCH v3 34/76] gpio: Drop unused mpc83xx_gpio driver Simon Glass 2023-02-01 20:19 ` [PATCH v3 35/76] imx: Rename CONFIG_MXS to CFG_MXS Simon Glass 2023-02-01 20:19 ` [PATCH v3 36/76] nand: Drop unused actl_nand driver Simon Glass 2023-02-01 20:19 ` [PATCH v3 37/76] mtd: Drop unused fsl_upm driver Simon Glass 2023-02-01 20:19 ` [PATCH v3 38/76] mtd: Drop unused fsmc_nand driver Simon Glass 2023-02-01 20:19 ` [PATCH v3 40/76] mtd: Drop unused nand_plat driver Simon Glass 2023-02-01 20:19 ` [PATCH v3 41/76] Makefile: Drop CONFIG_OF_EARLY_FLATTREE Simon Glass 2023-02-01 20:19 ` [PATCH v3 42/76] omap: Drop unused CONFIG_OMAP_USB_PHY Simon Glass 2023-02-01 20:19 ` [PATCH v3 44/76] ppc: Drop unused CONFIG_P2020DS Simon Glass 2023-02-01 20:19 ` [PATCH v3 45/76] gpio: Drop unused pca9698 driver Simon Glass 2023-02-01 20:19 ` [PATCH v3 46/76] samsung: Rename PINCTRL_EXYNOS78x0 Simon Glass 2023-02-03 6:04 ` Minkyu Kang 2023-02-01 20:19 ` [PATCH v3 47/76] power: Drop unused bat_trats driver and battery code Simon Glass 2023-02-01 20:19 ` [PATCH v3 48/76] power: Drop unused fg_max17042 driver and fuel gauge code Simon Glass 2023-02-01 20:20 ` [PATCH v3 49/76] power: Drop unused muic_max77693 driver and mfd code Simon Glass 2023-02-01 20:20 ` [PATCH v3 50/76] power: Drop unused muic_max8997 driver Simon Glass 2023-02-01 20:20 ` [PATCH v3 51/76] freescale: Drop unused pq-mds-pib driver Simon Glass 2023-02-01 20:20 ` [PATCH v3 52/76] rmobile: Drop CONFIG_RMOBILE Simon Glass 2023-02-01 20:20 ` [PATCH v3 53/76] rtc: Drop old and unused drivers Simon Glass 2023-02-01 20:20 ` [PATCH v3 54/76] mtd: Drop unused CONFIG_S32V234 Simon Glass 2023-02-01 20:20 ` [PATCH v3 55/76] mtd: Drop unused scf0403_lcd driver Simon Glass 2023-02-01 20:20 ` [PATCH v3 56/76] rmobile: Drop CONFIG_SH73A0 and associated code Simon Glass 2023-02-01 20:20 ` [PATCH v3 57/76] sh4: Drop unused pci_sh7780 driver Simon Glass 2023-02-01 20:20 ` [PATCH v3 58/76] Drop ubsha1 tool Simon Glass 2023-02-20 10:16 ` Peter Robinson 2023-02-21 19:41 ` Simon Glass 2023-02-22 8:08 ` Peter Robinson 2023-02-22 21:20 ` Simon Glass 2023-02-01 20:20 ` [PATCH v3 59/76] sysreset: at91: Correct Makefile rule for SYSRESET_AT91 Simon Glass 2023-02-01 20:20 ` [PATCH v3 60/76] gdsys: Drop unused fpga file Simon Glass 2023-02-01 20:20 ` [PATCH v3 61/76] sh4: Drop unused kona_i2c driver Simon Glass 2023-02-01 20:20 ` [PATCH v3 62/76] compulab: Drop CONFIG_TARGET_MCM_IMX8M_MINI Simon Glass 2023-02-01 20:20 ` [PATCH v3 63/76] freescale: Drop CONFIG_TARGET_MPC8536DS et al Simon Glass 2023-02-01 20:20 ` [PATCH v3 65/76] ppc: Makefile: Drop unused ppc4xx code Simon Glass 2023-02-01 20:20 ` [PATCH v3 66/76] armada: usb: net: Drop unused USB drivers Simon Glass 2023-02-01 20:20 ` [PATCH v3 67/76] usb: Drop unused ehci-faraday driver Simon Glass 2023-02-01 20:20 ` [PATCH v3 68/76] usb: Drop unused fotg210 gadget Simon Glass 2023-02-10 23:33 ` Samuel Holland 2023-02-11 1:06 ` Tom Rini 2023-02-01 20:20 ` [PATCH v3 69/76] rmobile: Drop unused ehci-rmobile driver Simon Glass 2023-02-01 20:20 ` [PATCH v3 70/76] usb: Drop unused ehci-vct driver Simon Glass 2023-02-01 20:20 ` [PATCH v3 71/76] usb: Drop unused sl811-hcd driver Simon Glass 2023-02-01 20:20 ` [PATCH v3 72/76] imx: Drop CONFIG_USE_PLUGIN Simon Glass 2023-02-01 20:20 ` [PATCH v3 73/76] freescale: Drop unused vsc3316_3308 driver Simon Glass 2023-02-01 20:20 ` [PATCH v3 74/76] tools: Drop xway-swap-bytes tool Simon Glass 2023-02-01 20:20 ` [PATCH v3 75/76] freescale: Drop unused zm7300 driver Simon Glass 2023-02-01 20:20 ` [PATCH v3 76/76] fdt: Drop use of non-existent OF_PLATDATA option Simon Glass
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox