Re: [RESEND PATCH v1 4/4] doc: t-head: lpi4a: document Lichee PI 4A board

[Leo Liang <ycliang@andestech.com>]

Hi YiXun,

On Fri, May 26, 2023 at 08:41:07PM +0800, Yixun Lan wrote:
> Reviewed-by: Wei Fu <wefu@redhat.com>
> Signed-off-by: Yixun Lan <dlan@gentoo.org>
> ---
>  doc/board/index.rst       |   1 +
>  doc/board/thead/index.rst |   9 +++
>  doc/board/thead/lpi4a.rst | 112 ++++++++++++++++++++++++++++++++++++++
>  3 files changed, 122 insertions(+)
>  create mode 100644 doc/board/thead/index.rst
>  create mode 100644 doc/board/thead/lpi4a.rst
> 
> diff --git a/doc/board/index.rst b/doc/board/index.rst
> index 9ef25b1091..aadc90af89 100644
> --- a/doc/board/index.rst
> +++ b/doc/board/index.rst
> @@ -45,6 +45,7 @@ Board-specific doc
>     starfive/index
>     ste/index
>     tbs/index
> +   thead/index
>     ti/index
>     toradex/index
>     variscite/index
> diff --git a/doc/board/thead/index.rst b/doc/board/thead/index.rst
> new file mode 100644
> index 0000000000..41566d3a36
> --- /dev/null
> +++ b/doc/board/thead/index.rst
> @@ -0,0 +1,9 @@
> +.. SPDX-License-Identifier: GPL-2.0+
> +
> +T-HEAD
> +========
> +
> +.. toctree::
> +   :maxdepth: 1
> +
> +   lpi4a
> diff --git a/doc/board/thead/lpi4a.rst b/doc/board/thead/lpi4a.rst
> new file mode 100644
> index 0000000000..3764e732af
> --- /dev/null
> +++ b/doc/board/thead/lpi4a.rst
> @@ -0,0 +1,112 @@
> +.. SPDX-License-Identifier: GPL-2.0+
> +
> +Sipeed's Lichee PI 4A based on T-HEAD TH1520 SoC
> +====================
> +

The underline is too short and would cause error when building docs.

Best regards,
Leo
> +TH1520 RISC-V SoC
> +---------------------
> +The TH1520 is 4+2 core 64-bit RISC-V SoC from Alibaba T-HEAD, it's capable of
> +running highest CPU frequency at 2.5 GHz, integrate Imagination GPU for graphics,
> +also with 4 TOPS NPU for AI acceleration.
> +
> +Mainline support
> +----------------
> +
> +The support for following drivers are already enabled:
> +
> +1. ns16550 UART Driver.
> +
> +Building
> +~~~~~~~~
> +
> +1. Add the RISC-V toolchain to your PATH.
> +2. Setup ARCH & cross compilation environment variable:
> +
> +.. code-block:: none
> +
> +   export CROSS_COMPILE=<riscv64 toolchain prefix>
> +
> +The U-Boot is capable of running in M-Mode, so we can directly build it.
> +
> +.. code-block:: console
> +
> +	cd <U-Boot-dir>
> +	make th1520_lpi4a_defconfig
> +	make
> +
> +This will generate u-boot-dtb.bin
> +
> +Booting
> +~~~~~~~
> +
> +Currently, we rely on vendor u-boot to initialize the clock, pinctrl subsystem,
> +and chain load the mainline u-boot image either via tftp or emmc storage,
> +then bootup from it.
> +
> +Sample boot log from Lichee PI 4A board via tftp
> +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> +
> +.. code-block:: none
> +
> +	brom_ver 8
> +	[APP][E] protocol_connect failed, exit.
> +
> +	U-Boot SPL 2020.01-00016-g8c870a6be8 (May 20 2023 - 01:04:49 +0000)
> +	FM[1] lpddr4x dualrank freq=3733 64bit dbi_off=n sdram init
> +	ddr initialized, jump to uboot
> +	image has no header
> +
> +
> +	U-Boot 2020.01-00016-g8c870a6be8 (May 20 2023 - 01:04:49 +0000)
> +
> +	CPU:   rv64imafdcvsu
> +	Model: T-HEAD c910 light
> +	DRAM:  8 GiB
> +	C910 CPU FREQ: 750MHz
> +	AHB2_CPUSYS_HCLK FREQ: 250MHz
> +	AHB3_CPUSYS_PCLK FREQ: 125MHz
> +	PERISYS_AHB_HCLK FREQ: 250MHz
> +	PERISYS_APB_PCLK FREQ: 62MHz
> +	GMAC PLL POSTDIV FREQ: 1000MHZ
> +	DPU0 PLL POSTDIV FREQ: 1188MHZ
> +	DPU1 PLL POSTDIV FREQ: 1188MHZ
> +	MMC:   sdhci@ffe7080000: 0, sd@ffe7090000: 1
> +	Loading Environment from MMC... OK
> +	Error reading output register
> +	Warning: cannot get lcd-en GPIO
> +	LCD panel cannot be found : -121
> +	splash screen startup cost 16 ms
> +	In:    serial
> +	Out:   serial
> +	Err:   serial
> +	Net:
> +	Warning: ethernet@ffe7070000 using MAC address from ROM
> +	eth0: ethernet@ffe7070000ethernet@ffe7070000:0 is connected to ethernet@ffe7070000.  Reconnecting to ethernet@ffe7060000
> +
> +	Warning: ethernet@ffe7060000 (eth1) using random MAC address - 42:25:d4:16:5f:fc
> +	, eth1: ethernet@ffe7060000
> +	Hit any key to stop autoboot:  2
> +	ethernet@ffe7060000 Waiting for PHY auto negotiation to complete.. done
> +	Speed: 1000, full duplex
> +	Using ethernet@ffe7070000 device
> +	TFTP from server 192.168.8.50; our IP address is 192.168.8.45
> +	Filename 'u-boot-dtb.bin'.
> +	Load address: 0x1c00000
> +	Loading: * #########################
> +		 8 MiB/s
> +	done
> +	Bytes transferred = 376686 (5bf6e hex)
> +	## Starting application at 0x01C00000 ...
> +
> +        U-Boot 2023.07-rc2-00004-g1befbe31c1 (May 23 2023 - 18:40:01 +0800)
> +
> +        CPU:   rv64imafdc
> +        Model: Sipeed Lichee Pi 4A
> +        DRAM:  8 GiB
> +        Core:  13 devices, 6 uclasses, devicetree: separate
> +        Loading Environment from <NULL>... OK
> +        In:    serial@ffe7014000
> +        Out:   serial@ffe7014000
> +        Err:   serial@ffe7014000
> +        Model: Sipeed Lichee Pi 4A
> +        LPI4A=>
> -- 
> 2.40.0
>