[U-Boot] [PATCH v2 5/5] sunxi: DT: add support for Pinebook

["André Przywara" <andre.przywara@arm.com>]

On 10/17/18 6:09 AM, Vasily Khoruzhick wrote:

Hi,

> Pinebook is a laptop produced by Pine64, with USB-connected keyboard,
> USB-connected touchpad and an eDP LCD panel connected via a RGB-eDP
> bridge from Analogix.
> 
> Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
> ---
>  arch/arm/dts/Makefile                |   3 +-
>  arch/arm/dts/sun50i-a64-pinebook.dts | 306 +++++++++++++++++++++++++++
>  configs/pinebook_defconfig           |  27 +++
>  3 files changed, 335 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm/dts/sun50i-a64-pinebook.dts
>  create mode 100644 configs/pinebook_defconfig
> 
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index dfe9335a04..ccb93f1e46 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -404,7 +404,8 @@ dtb-$(CONFIG_MACH_SUN50I) += \
>  	sun50i-a64-orangepi-win.dtb \
>  	sun50i-a64-pine64-plus.dtb \
>  	sun50i-a64-pine64.dtb \
> -	sun50i-a64-sopine-baseboard.dtb
> +	sun50i-a64-sopine-baseboard.dtb \
> +	sun50i-a64-pinebook.dtb
>  dtb-$(CONFIG_MACH_SUN9I) += \
>  	sun9i-a80-optimus.dtb \
>  	sun9i-a80-cubieboard4.dtb \
> diff --git a/arch/arm/dts/sun50i-a64-pinebook.dts b/arch/arm/dts/sun50i-a64-pinebook.dts
> new file mode 100644
> index 0000000000..5d111fab64
> --- /dev/null
> +++ b/arch/arm/dts/sun50i-a64-pinebook.dts
> @@ -0,0 +1,306 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz>
> + * Copyright (C) 2018 Vasily Khoruzhick <anarsoul@gmail.com>
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-a64.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> +	model = "Pinebook";
> +	compatible = "pine64,pinebook", "allwinner,sun50i-a64";
> +
> +	aliases {
> +		serial0 = &uart0;
> +		ethernet0 = &rtl8723cs;
> +	};
> +
> +	vdd_bl: regulator at 0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "bl-3v3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
> +		enable-active-high;
> +	};
> +
> +	backlight: backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm 0 50000 0>;
> +		brightness-levels = <0 5 10 15 20 30 40 55 70 85 100>;
> +		default-brightness-level = <2>;
> +		enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
> +		power-supply = <&vdd_bl>;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +
> +		framebuffer-lcd {
> +			panel-supply = <&reg_dc1sw>;
> +			dvdd25-supply = <&reg_dldo2>;
> +			dvdd12-supply = <&reg_fldo1>;
> +		};
> +	};
> +
> +	gpio_keys {
> +		compatible = "gpio-keys";
> +
> +		lid_switch {
> +			label = "Lid Switch";
> +			gpios = <&r_pio 0 12 GPIO_ACTIVE_LOW>; /* PL12 */
> +			linux,input-type = <EV_SW>;
> +			linux,code = <SW_LID>;
> +			linux,can-disable;
> +			wakeup-source;
> +		};
> +	};
> +
> +	reg_vcc3v3: vcc3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc3v3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	wifi_pwrseq: wifi_pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
> +	};
> +
> +	speaker_amp: speaker_amp {
> +		compatible = "simple-audio-amplifier";
> +		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>;
> +	};

I see that this is the only sound related node not dependent on any
.dtsi nodes, but how useful is it to have it in here on its own?
Shouldn't we wait until all sound nodes are agreed upon and merged?

> +};
> +
> +&ehci0 {
> +	phys = <&usbphy 0>;
> +	phy-names = "usb";
> +	status = "okay";
> +};
> +
> +&ehci1 {
> +	status = "okay";
> +};
> +
> +&mmc0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc0_pins>;
> +	vmmc-supply = <&reg_dcdc1>;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
> +	cd-inverted;
> +	disable-wp;
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&mmc1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc1_pins>;
> +	vmmc-supply = <&reg_dldo4>;
> +	vqmmc-supply = <&reg_eldo1>;
> +	mmc-pwrseq = <&wifi_pwrseq>;
> +	bus-width = <4>;
> +	non-removable;
> +	status = "okay";
> +
> +	rtl8723cs: wifi at 1 {
> +		reg = <1>;
> +	};
> +};
> +
> +&mmc2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc2_pins>;
> +	vmmc-supply = <&reg_dcdc1>;
> +	vqmmc-supply = <&reg_eldo1>;
> +	bus-width = <8>;
> +	non-removable;
> +	cap-mmc-hw-reset;
> +	mmc-hs200-1_8v;
> +	status = "okay";
> +};
> +
> +&ohci0 {
> +	phys = <&usbphy 0>;
> +	phy-names = "usb";
> +	status = "okay";
> +};
> +
> +&ohci1 {
> +	status = "okay";
> +};
> +
> +&pwm {
> +	status = "okay";
> +};
> +
> +&r_rsb {
> +	status = "okay";
> +
> +	axp803: pmic at 3a3 {
> +		compatible = "x-powers,axp803";
> +		reg = <0x3a3>;
> +		interrupt-parent = <&r_intc>;
> +		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +};
> +
> +/* The ANX6345 eDP-bridge is on r_i2c */
> +&r_i2c {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&r_i2c_pins_a>;
> +	status = "okay";

Nit: please add an empty line here, to separate the slave section from
the master.

> +	anx6345: edp-bridge at 38 {
> +		compatible = "analogix,anx6345";
> +		reg = <0x38>;
> +		reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */
> +		status = "okay";
> +	};

Do you have any plans on upstreaming this binding?


> +};
> +
> +#include "axp803.dtsi"
> +
> +&reg_aldo1 {
> +	regulator-min-microvolt = <2800000>;
> +	regulator-max-microvolt = <2800000>;
> +	regulator-name = "vcc-csi";
> +};
> +
> +&reg_aldo2 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1800000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "vcc-pl";
> +};
> +
> +&reg_aldo3 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <2700000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "vcc-pll-avcc";
> +};
> +
> +&reg_dc1sw {
> +	regulator-name = "vcc-lcd";
> +};
> +
> +&reg_dcdc1 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <3300000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "vcc-3v3";
> +};
> +
> +&reg_dcdc2 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1000000>;
> +	regulator-max-microvolt = <1300000>;
> +	regulator-name = "vdd-cpux";
> +};
> +
> +/* DCDC3 is polyphased with DCDC2 */
> +
> +&reg_dcdc5 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1200000>;
> +	regulator-max-microvolt = <1200000>;
> +	regulator-name = "vcc-dram";
> +};
> +
> +&reg_dcdc6 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1100000>;
> +	regulator-max-microvolt = <1100000>;
> +	regulator-name = "vdd-sys";
> +};
> +
> +&reg_dldo1 {
> +	regulator-min-microvolt = <3300000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "vcc-hdmi";
> +};
> +
> +&reg_dldo2 {
> +	regulator-min-microvolt = <2500000>;
> +	regulator-max-microvolt = <2500000>;
> +	regulator-name = "vcc-edp";
> +};
> +
> +&reg_dldo3 {
> +	regulator-min-microvolt = <3300000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "avdd-csi";
> +};
> +
> +&reg_dldo4 {
> +	regulator-min-microvolt = <3300000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "vcc-wifi";
> +};
> +
> +&reg_eldo1 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1800000>;
> +	regulator-max-microvolt = <1800000>;
> +	regulator-name = "cpvdd";
> +};
> +
> +&reg_eldo3 {
> +	regulator-min-microvolt = <1800000>;
> +	regulator-max-microvolt = <1800000>;
> +	regulator-name = "vdd-1v8-csi";
> +};
> +
> +&reg_fldo1 {
> +	regulator-min-microvolt = <1200000>;
> +	regulator-max-microvolt = <1200000>;
> +	regulator-name = "vcc-1v2-hsic";
> +};
> +
> +&reg_fldo2 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1100000>;
> +	regulator-max-microvolt = <1100000>;
> +	regulator-name = "vdd-cpus";
> +};
> +
> +&reg_ldo_io0 {
> +	regulator-min-microvolt = <3300000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "vcc-usb";
> +	status = "okay";
> +};
> +
> +&reg_rtc_ldo {
> +	regulator-name = "vcc-rtc";
> +};
> +
> +&simplefb_hdmi {
> +	vcc-hdmi-supply = <&reg_dldo1>;
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_pins_a>;
> +	status = "okay";
> +};
> +
> +&usb_otg {
> +	dr_mode = "host";
> +};
> +
> +&usbphy {
> +	usb0_vbus-supply = <&reg_ldo_io0>;
> +	usb1_vbus-supply = <&reg_ldo_io0>;
> +	status = "okay";
> +};
> diff --git a/configs/pinebook_defconfig b/configs/pinebook_defconfig
> new file mode 100644
> index 0000000000..f5190d96d2
> --- /dev/null
> +++ b/configs/pinebook_defconfig
> @@ -0,0 +1,27 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_SUNXI=y
> +CONFIG_SPL=y
> +CONFIG_MACH_SUN50I=y
> +CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y

I think you can drop this.

> +CONFIG_SUNXI_DRAM_LPDDR3_STOCK=y
> +CONFIG_DRAM_CLK=552
> +CONFIG_DRAM_ZQ=3881949
> +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> +CONFIG_R_I2C_ENABLE=y
> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
> +# CONFIG_SPL_LEGACY_IMAGE_SUPPORT is not set

Why these two? I see that they save 219 bytes of the SPL, but the image
size is still way below the limit.
So I'd prefer to not deviate from the other boards here.

> +# CONFIG_CMD_FLASH is not set
> +# CONFIG_SPL_DOS_PARTITION is not set
> +# CONFIG_SPL_EFI_PARTITION is not set
> +CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-pinebook"
> +# CONFIG_MMC_VERBOSE is not set

Why this one? Doesn't seem to affect SPL size?

Cheers,
Andre.


> +CONFIG_DM_REGULATOR=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_PWM=y
> +CONFIG_PWM_SUNXI=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
> +# CONFIG_USB_GADGET is not set
> +CONFIG_VIDEO_BRIDGE=y
> +CONFIG_VIDEO_BRIDGE_ANALOGIX_ANX6345=y
>