[U-Boot] rk3288 (Tinkerboard) not booting【请注意，邮件由u-boot-bounces@lists.denx.de代发】

[Alexander von Gluck IV <kallisti5@unixzen.com>]

Oh, a difference:

$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
    cat spl/u-boot-spl-dtb.bin >> idbloader.img

I'm using the idbloader.img that u-boot automatically spits out.

$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader-manual.img
Image Type:   Rockchip RK32 (SD/MMC) boot image
Data Size:    20480 bytes
$ cat spl/u-boot-spl-dtb.bin >> idbloader-manual.img

However.. the generated idbloader-manual.img from the commands above is identical to idbloader.img
that u-boot produces compared with md5sum.


Are you writing the following?

  sudo dd if=idbloader.img of=/dev/sdd seek=64
  sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384

(where /dev/sdd is a MicroSD card)

These should be enough to get into u-boot at startup... correct?

I'm not missing some requirement of u-boot.bin on a FAT32 partition or something?

 -- Alex

September 23, 2019 8:31 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:

> On Mon, Sep 23, 2019 at 01:06:35PM +0000, Alexander von Gluck IV wrote:
> 
>> Ok, looking for differences now..
>> 
>> * Older Tinker Board? (I'm not using the Tinker Board S)
> 
> yes, the original one
> 
>> * Same steps?
> 
> along the lines of
> 
> gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig
> gmake CROSS_COMPILE="arm-none-eabi-" all
> tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
> cat spl/u-boot-spl-dtb.bin >> idbloader.img
> 
>> * Same config? tinker-rk3288_defconfig?
> 
> yes
> 
>> * Uart 115200?
> 
> yes
> 
>> * Any HDMI Video output?
> 
> no hdmi connected only serial
> 
>> * GCC version?
> 
> gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target
> 
>> September 23, 2019 12:34 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
>> 
>> On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
>> 
>> Hello!
>> 
>> There is no uart output and no video with u-boot master.
>> The board works as expected booting the Asus Armbian image on an SD.
>> 
>> At this point i'd be happy to get some u-boot uart output :-)
>> 
>> -- Alex
>> 
>> uart output works here with the latest master
>> (780a17e814503f71d1b51d578b32bc9c89933183)
>> 
>> U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20)
>> Trying to boot from BOOTROM
>> Returning to boot ROM...
>> 
>> U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
>> Trying to boot from MMC1
>> 
>> U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
>> 
>> Model: Tinker-RK3288
>> DRAM: 2 GiB
>> MMC: dwmmc at ff0c0000: 1
>> Loading Environment from MMC... *** Warning - bad CRC, using default environment
>> 
>> In: serial
>> Out: serial
>> Err: serial
>> Model: Tinker-RK3288
>> rockchip_dnl_key_pressed: adc_channel_single_shot fail!
>> Net: eth0: ethernet at ff290000
>> Hit any key to stop autoboot: 0
>> switch to partitions #0, OK
>> mmc1 is current device
>> Scanning mmc 1:1...
>> Found EFI removable media binary efi/boot/bootarm.efi
>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>> Scanning disk dwmmc at ff0c0000.blk...
>> Found 3 disks
>> BootOrder not defined
>> EFI boot manager: Cannot load any image
>> 88176 bytes read in 9 ms (9.3 MiB/s)
>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>> OpenBSD/armv7 BOOTARM 1.6
>> 
>> boot>
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> https://lists.denx.de/listinfo/u-boot