[U-Boot] [PATCH 2/7] mmc: uniphier-sd: Properly handle pin voltage configuration

[Jaehoon Chung <jh80.chung@samsung.com>]

On 01/07/2018 04:29 AM, Marek Vasut wrote:
> Factor out the regulator handling into set_ios and add support for
> selecting pin configuration based on the voltage to support UHS modes.
> 
> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
> Cc: Jaehoon Chung <jh80.chung@samsung.com>
> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
> ---
>  drivers/mmc/uniphier-sd.c | 33 ++++++++++++++++++++++++---------
>  1 file changed, 24 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/mmc/uniphier-sd.c b/drivers/mmc/uniphier-sd.c
> index 552e37d852..ebcc12a8ae 100644
> --- a/drivers/mmc/uniphier-sd.c
> +++ b/drivers/mmc/uniphier-sd.c
> @@ -10,6 +10,7 @@
>  #include <fdtdec.h>
>  #include <mmc.h>
>  #include <dm.h>
> +#include <dm/pinctrl.h>
>  #include <linux/compat.h>
>  #include <linux/dma-direction.h>
>  #include <linux/io.h>
> @@ -134,6 +135,9 @@ struct uniphier_sd_priv {
>  #define UNIPHIER_SD_CAP_DMA_INTERNAL	BIT(1)	/* have internal DMA engine */
>  #define UNIPHIER_SD_CAP_DIV1024		BIT(2)	/* divisor 1024 is available */
>  #define UNIPHIER_SD_CAP_64BIT		BIT(3)	/* Controller is 64bit */
> +#ifdef CONFIG_DM_REGULATOR
> +	struct udevice *vqmmc_dev;
> +#endif
>  };
>  
>  static u64 uniphier_sd_readq(struct uniphier_sd_priv *priv, unsigned int reg)
> @@ -676,6 +680,24 @@ static void uniphier_sd_set_clk_rate(struct uniphier_sd_priv *priv,
>  	udelay(1000);
>  }
>  
> +static void uniphier_sd_set_pins(struct udevice *dev)
> +{
> +	struct uniphier_sd_priv *priv = dev_get_priv(dev);
> +	struct mmc *mmc = mmc_get_mmc_dev(dev);
> +
> +	if (priv->vqmmc_dev) {

You added #ifdef CONFIG_DM_REGULATOR in struct uniphier_sd_priv.
If CONFIG_DM_REGULATOR is disabled, it can't refer the vqmmc_dev.?

> +		if (mmc->signal_voltage == MMC_SIGNAL_VOLTAGE_180)
> +			regulator_set_value(priv->vqmmc_dev, 1800000);
> +		else
> +			regulator_set_value(priv->vqmmc_dev, 3300000);
> +	}
> +
> +	if (mmc->signal_voltage == MMC_SIGNAL_VOLTAGE_180)
> +		pinctrl_select_state(dev, "state_uhs");
> +	else
> +		pinctrl_select_state(dev, "default");
> +}
> +
>  static int uniphier_sd_set_ios(struct udevice *dev)
>  {
>  	struct uniphier_sd_priv *priv = dev_get_priv(dev);
> @@ -690,6 +712,7 @@ static int uniphier_sd_set_ios(struct udevice *dev)
>  		return ret;
>  	uniphier_sd_set_ddr_mode(priv, mmc);
>  	uniphier_sd_set_clk_rate(priv, mmc);
> +	uniphier_sd_set_pins(dev);
>  
>  	return 0;
>  }
> @@ -757,9 +780,6 @@ static int uniphier_sd_probe(struct udevice *dev)
>  	fdt_addr_t base;
>  	struct clk clk;
>  	int ret;
> -#ifdef CONFIG_DM_REGULATOR
> -	struct udevice *vqmmc_dev;
> -#endif
>  
>  	base = devfdt_get_addr(dev);
>  	if (base == FDT_ADDR_T_NONE)
> @@ -770,12 +790,7 @@ static int uniphier_sd_probe(struct udevice *dev)
>  		return -ENOMEM;
>  
>  #ifdef CONFIG_DM_REGULATOR
> -	ret = device_get_supply_regulator(dev, "vqmmc-supply", &vqmmc_dev);
> -	if (!ret) {
> -		/* Set the regulator to 3.3V until we support 1.8V modes */
> -		regulator_set_value(vqmmc_dev, 3300000);
> -		regulator_set_enable(vqmmc_dev, true);
> -	}
> +	ret = device_get_supply_regulator(dev, "vqmmc-supply", &priv->vqmmc_dev);
>  #endif
>  
>  	ret = clk_get_by_index(dev, 0, &clk);
>