From: Cyrille Pitchen <cyrille.pitchen@atmel.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 0/8] sf: improve support of (Q)SPI flash memories
Date: Fri, 19 May 2017 16:59:38 +0200 [thread overview]
Message-ID: <cover.1495204848.git.cyrille.pitchen@atmel.com> (raw)
Hi all,
this series of patches has been tested on u-boot-2017.03-at91 then ported
to the 'master' branch of the u-boot-spi.git tree.
Tests were passed with a sama5d2 xplained board which embeds both SPI and
QSPI controllers.
The following tests have been passed:
- QSPI0 + Macronix MX25L25673G:
+ probe: OK
+ Fast Read 1-1-4 at offset 0x10000 (u-boot env): OK
+ Page Program 1-1-4 at offset 0x10000: OK
The Macronix datasheet tells that only Page Program 1-4-4 is
supported, not Page Program 1-1-4, however it worked, I don't know
why...
- QSPI0 + Microchip SST26
+ probe: OK
+ Fast Read 1-1-4 at offset 0x10000 (u-boot env): OK
+ Page Program 1-1-1 at offset 0x10000: OK
SST26 memories support Page Program 1-4-4 but with the op code of
Page Program 1-1-4, which is not standard so I don't use it.
- QSPI0 + Adesto AT25DF321A
+ probe: OK
+ Fast Read 1-1-1 at offset 0x10000 (u-boot env): OK
+ Page Program 1-1-1 at offset 0x10000: OK
- SPI0 + Adesto AT25DF321A
+ probe: OK
+ Fast Read 1-1-1 at offset 0x6000 (u-boot env): OK
+ Page Program 1-1-1 at offest 0x6000: OK
- SPI1 + Atmel AT45
+ probe: OK
+ Read at offset 0: OK
+ Write at offset 0: OK <- I didn't try offset other than 0.
During my tests, I used:
- setenv/saveenv, reboot, printenv
or
- sf probe, sf read, sf write
Best regards,
Cyrille
Cyrille Pitchen (8):
spi: add support of SPI flash commands
sf: describe all SPI flash commands with 'struct spi_flash_command'
sf: select the relevant SPI flash protocol for read and write commands
sf: differentiate Page Program 1-1-4 and 1-4-4
sf: add 'addr_len' member to 'struct spi_flash'
sf: add new option to support SPI flash above 16MiB
sf: add support to Microchip SST26 QSPI memories
sf: add driver for Atmel QSPI controller
drivers/mtd/spi/Kconfig | 15 +-
drivers/mtd/spi/sf.c | 78 ++++++--
drivers/mtd/spi/sf_dataflash.c | 119 ++++++------
drivers/mtd/spi/sf_internal.h | 48 +++--
drivers/mtd/spi/spi_flash.c | 338 +++++++++++++++++++++++----------
drivers/mtd/spi/spi_flash_ids.c | 5 +
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/atmel_qspi.c | 404 ++++++++++++++++++++++++++++++++++++++++
drivers/spi/atmel_qspi.h | 169 +++++++++++++++++
drivers/spi/spi-uclass.c | 40 ++++
drivers/spi/spi.c | 13 ++
include/spi.h | 168 +++++++++++++++++
include/spi_flash.h | 6 +
14 files changed, 1222 insertions(+), 189 deletions(-)
create mode 100644 drivers/spi/atmel_qspi.c
create mode 100644 drivers/spi/atmel_qspi.h
--
2.7.4
next reply other threads:[~2017-05-19 14:59 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-05-19 14:59 Cyrille Pitchen [this message]
2017-05-19 14:59 ` [U-Boot] [PATCH 1/8] spi: add support of SPI flash commands Cyrille Pitchen
2017-05-22 1:17 ` Yang, Wenyou
2017-05-19 14:59 ` [U-Boot] [PATCH 2/8] sf: describe all SPI flash commands with 'struct spi_flash_command' Cyrille Pitchen
2017-05-22 1:18 ` Yang, Wenyou
2017-05-19 14:59 ` [U-Boot] [PATCH 3/8] sf: select the relevant SPI flash protocol for read and write commands Cyrille Pitchen
2017-05-22 1:18 ` Yang, Wenyou
2017-05-19 14:59 ` [U-Boot] [PATCH 4/8] sf: differentiate Page Program 1-1-4 and 1-4-4 Cyrille Pitchen
2017-05-22 1:19 ` Yang, Wenyou
2017-05-19 14:59 ` [U-Boot] [PATCH 5/8] sf: add 'addr_len' member to 'struct spi_flash' Cyrille Pitchen
2017-05-22 1:19 ` Yang, Wenyou
2017-05-19 14:59 ` [U-Boot] [PATCH 6/8] sf: add new option to support SPI flash above 16MiB Cyrille Pitchen
2017-05-22 1:20 ` Yang, Wenyou
2017-05-19 14:59 ` [U-Boot] [PATCH 7/8] sf: add support to Microchip SST26 QSPI memories Cyrille Pitchen
2017-05-22 1:20 ` Yang, Wenyou
2017-05-19 14:59 ` [U-Boot] [PATCH 8/8] sf: add driver for Atmel QSPI controller Cyrille Pitchen
2017-05-22 1:21 ` Yang, Wenyou
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=cover.1495204848.git.cyrille.pitchen@atmel.com \
--to=cyrille.pitchen@atmel.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox