[U-Boot] rk3288 (Tinkerboard) not booting

[U-Boot] rk3288 (Tinkerboard) not booting

[Alexander von Gluck IV]

Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)

The docs seem to recommend:
$ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin out

However, that produces:
Warning: SPL image is too large (size 0xb000) and will not boot

I saw this patch to disable I2C in the SPL to reduce its size:
https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-tinker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patch

However, that breaks the build :-|

 LD spl/u-boot-spl
arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_write':
/tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference to `dm_i2c_write'
arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_read':
/tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read'
make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
make: *** [Makefile:1762: spl/u-boot-spl] Error 2
make: Leaving directory '/tmp/arm-build'
Disabling SPL Power then results in an error compiling MMC support
Any alternative methods to getting u-boot running from SD?
Rockchip devices seem to be kind of complex to get going :-|
 -- Alex

[U-Boot] rk3288 (Tinkerboard) not booting

[Michael Nazzareno Trimarchi]

Hi

Please use the latest uboot. The fixes should be already merged

Mcihael

On Sun, Sep 22, 2019 at 10:53 PM Alexander von Gluck IV
<kallisti5@unixzen.com> wrote:
>
> Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
>
> The docs seem to recommend:
> $ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin out
>
> However, that produces:
> Warning: SPL image is too large (size 0xb000) and will not boot
>
> I saw this patch to disable I2C in the SPL to reduce its size:
> https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-tinker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patch
>
> However, that breaks the build :-|
>
>  LD spl/u-boot-spl
> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_write':
> /tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference to `dm_i2c_write'
> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_read':
> /tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read'
> make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
> make: *** [Makefile:1762: spl/u-boot-spl] Error 2
> make: Leaving directory '/tmp/arm-build'
> Disabling SPL Power then results in an error compiling MMC support
> Any alternative methods to getting u-boot running from SD?
> Rockchip devices seem to be kind of complex to get going :-|
>  -- Alex
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot



-- 
| Michael Nazzareno Trimarchi                     Amarula Solutions BV |
| COO  -  Founder                                      Cruquiuskade 47 |
| +31(0)851119172                                 Amsterdam 1018 AM NL |
|                  [`as] http://www.amarulasolutions.com               |

[U-Boot] rk3288 (Tinkerboard) not booting

[Alexander von Gluck IV]

Using master from git://git.denx.de/u-boot.git

commit 390183b58179ddaf986422f4d9446c596660f7e0 (HEAD -> master, origin/master, origin/HEAD)
Merge: d6c7309f56 79907a4f84
Author: Tom Rini <trini@konsulko.com>
Date:   Sat Sep 21 07:31:23 2019 -0400

    Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
    
    Pull request for UEFI sub-system for v2019.10-rc4 (5)
    
    This patch set fixes errors in the UEFI sub-system and adds a function to
    compare u16 strings which is prerequisite for further patches.


Same error:


$ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin out
Warning: SPL image is too large (size 0xb000) and will not boot
Error: image verification failed


$ ls -lah spl/u-boot-spl-dtb.bin
-rw-rw-r-- 1 kallisti5 kallisti5 43K Sep 22 16:17 spl/u-boot-spl-dtb.bin



September 22, 2019 4:03 PM, "Michael Nazzareno Trimarchi" <michael@amarulasolutions.com> wrote:

> Hi
> 
> Please use the latest uboot. The fixes should be already merged
> 
> Mcihael
> 
> On Sun, Sep 22, 2019 at 10:53 PM Alexander von Gluck IV
> <kallisti5@unixzen.com> wrote:
> 
>> Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
>> 
>> The docs seem to recommend:
>> $ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin out
>> 
>> However, that produces:
>> Warning: SPL image is too large (size 0xb000) and will not boot
>> 
>> I saw this patch to disable I2C in the SPL to reduce its size:
>> https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-
>> inker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patch
>> 
>> However, that breaks the build :-|
>> 
>> LD spl/u-boot-spl
>> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_write':
>> /tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference to `dm_i2c_write'
>> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_read':
>> /tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read'
>> make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
>> make: *** [Makefile:1762: spl/u-boot-spl] Error 2
>> make: Leaving directory '/tmp/arm-build'
>> Disabling SPL Power then results in an error compiling MMC support
>> Any alternative methods to getting u-boot running from SD?
>> Rockchip devices seem to be kind of complex to get going :-|
>> -- Alex
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> https://lists.denx.de/listinfo/u-boot
> 
> --
> | Michael Nazzareno Trimarchi Amarula Solutions BV |
> | COO - Founder Cruquiuskade 47 |
> | +31(0)851119172 Amsterdam 1018 AM NL |
> | [`as] http://www.amarulasolutions.com |

[U-Boot] rk3288 (Tinkerboard) not booting

[Michael Nazzareno Trimarchi]

Hi

https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip/commits/master

make idbloader.img

Michael

On Sun, Sep 22, 2019 at 11:22 PM Alexander von Gluck IV
<kallisti5@unixzen.com> wrote:
>
> Using master from git://git.denx.de/u-boot.git
>
> commit 390183b58179ddaf986422f4d9446c596660f7e0 (HEAD -> master, origin/master, origin/HEAD)
> Merge: d6c7309f56 79907a4f84
> Author: Tom Rini <trini@konsulko.com>
> Date:   Sat Sep 21 07:31:23 2019 -0400
>
>     Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
>
>     Pull request for UEFI sub-system for v2019.10-rc4 (5)
>
>     This patch set fixes errors in the UEFI sub-system and adds a function to
>     compare u16 strings which is prerequisite for further patches.
>
>
> Same error:
>
>
> $ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin out
> Warning: SPL image is too large (size 0xb000) and will not boot
> Error: image verification failed
>
>
> $ ls -lah spl/u-boot-spl-dtb.bin
> -rw-rw-r-- 1 kallisti5 kallisti5 43K Sep 22 16:17 spl/u-boot-spl-dtb.bin
>
>
>
> September 22, 2019 4:03 PM, "Michael Nazzareno Trimarchi" <michael@amarulasolutions.com> wrote:
>
> > Hi
> >
> > Please use the latest uboot. The fixes should be already merged
> >
> > Mcihael
> >
> > On Sun, Sep 22, 2019 at 10:53 PM Alexander von Gluck IV
> > <kallisti5@unixzen.com> wrote:
> >
> >> Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
> >>
> >> The docs seem to recommend:
> >> $ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin out
> >>
> >> However, that produces:
> >> Warning: SPL image is too large (size 0xb000) and will not boot
> >>
> >> I saw this patch to disable I2C in the SPL to reduce its size:
> >> https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-
> >> inker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patch
> >>
> >> However, that breaks the build :-|
> >>
> >> LD spl/u-boot-spl
> >> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_write':
> >> /tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference to `dm_i2c_write'
> >> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_read':
> >> /tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read'
> >> make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
> >> make: *** [Makefile:1762: spl/u-boot-spl] Error 2
> >> make: Leaving directory '/tmp/arm-build'
> >> Disabling SPL Power then results in an error compiling MMC support
> >> Any alternative methods to getting u-boot running from SD?
> >> Rockchip devices seem to be kind of complex to get going :-|
> >> -- Alex
> >> _______________________________________________
> >> U-Boot mailing list
> >> U-Boot at lists.denx.de
> >> https://lists.denx.de/listinfo/u-boot
> >
> > --
> > | Michael Nazzareno Trimarchi Amarula Solutions BV |
> > | COO - Founder Cruquiuskade 47 |
> > | +31(0)851119172 Amsterdam 1018 AM NL |
> > | [`as] http://www.amarulasolutions.com |



-- 
| Michael Nazzareno Trimarchi                     Amarula Solutions BV |
| COO  -  Founder                                      Cruquiuskade 47 |
| +31(0)851119172                                 Amsterdam 1018 AM NL |
|                  [`as] http://www.amarulasolutions.com               |

[U-Boot] rk3288 (Tinkerboard) not booting

[Alexander von Gluck IV]

$ sudo dd if=idbloader.img of=/dev/sdd seek=64
$ sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384


Still nothing.


September 22, 2019 4:47 PM, "Michael Nazzareno Trimarchi" <michael@amarulasolutions.com> wrote:

> Hi
> 
> https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip/commits/master
> 
> make idbloader.img
> 
> Michael
> 
> On Sun, Sep 22, 2019 at 11:22 PM Alexander von Gluck IV
> <kallisti5@unixzen.com> wrote:
> 
>> Using master from git://git.denx.de/u-boot.git
>> 
>> commit 390183b58179ddaf986422f4d9446c596660f7e0 (HEAD -> master, origin/master, origin/HEAD)
>> Merge: d6c7309f56 79907a4f84
>> Author: Tom Rini <trini@konsulko.com>
>> Date: Sat Sep 21 07:31:23 2019 -0400
>> 
>> Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
>> 
>> Pull request for UEFI sub-system for v2019.10-rc4 (5)
>> 
>> This patch set fixes errors in the UEFI sub-system and adds a function to
>> compare u16 strings which is prerequisite for further patches.
>> 
>> Same error:
>> 
>> $ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin out
>> Warning: SPL image is too large (size 0xb000) and will not boot
>> Error: image verification failed
>> 
>> $ ls -lah spl/u-boot-spl-dtb.bin
>> -rw-rw-r-- 1 kallisti5 kallisti5 43K Sep 22 16:17 spl/u-boot-spl-dtb.bin
>> 
>> September 22, 2019 4:03 PM, "Michael Nazzareno Trimarchi" <michael@amarulasolutions.com> wrote:
>> 
>> Hi
>> 
>> Please use the latest uboot. The fixes should be already merged
>> 
>> Mcihael
>> 
>> On Sun, Sep 22, 2019 at 10:53 PM Alexander von Gluck IV
>> <kallisti5@unixzen.com> wrote:
>> 
>> Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
>> 
>> The docs seem to recommend:
>> $ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin out
>> 
>> However, that produces:
>> Warning: SPL image is too large (size 0xb000) and will not boot
>> 
>> I saw this patch to disable I2C in the SPL to reduce its size:
>> https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-
>> inker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patch
>> 
>> However, that breaks the build :-|
>> 
>> LD spl/u-boot-spl
>> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_write':
>> /tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference to `dm_i2c_write'
>> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_read':
>> /tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read'
>> make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
>> make: *** [Makefile:1762: spl/u-boot-spl] Error 2
>> make: Leaving directory '/tmp/arm-build'
>> Disabling SPL Power then results in an error compiling MMC support
>> Any alternative methods to getting u-boot running from SD?
>> Rockchip devices seem to be kind of complex to get going :-|
>> -- Alex
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> https://lists.denx.de/listinfo/u-boot
>> 
>> --
>> | Michael Nazzareno Trimarchi Amarula Solutions BV |
>> | COO - Founder Cruquiuskade 47 |
>> | +31(0)851119172 Amsterdam 1018 AM NL |
>> | [`as] http://www.amarulasolutions.com |
> 
> --
> | Michael Nazzareno Trimarchi Amarula Solutions BV |
> | COO - Founder Cruquiuskade 47 |
> | +31(0)851119172 Amsterdam 1018 AM NL |
> | [`as] http://www.amarulasolutions.com |

[U-Boot] rk3288 (Tinkerboard) not booting

[Alexander von Gluck IV]

Sorry for spam, reposting with more context :-)

$ make clean
$ make tinker-rk3288_defconfig
$ ARCH=arm CROSS_COMPILE=$TOOLCHAIN/bin/arm-unknown-haiku- make -j2

$ sudo dd if=idbloader.img of=/dev/sdd seek=64
$ sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384

I can confirm this toolchain successfully builds working u-boots
for 4 other 32-bit arm boards. (gcc version 8.3.0 (GCC))


September 22, 2019 5:00 PM, "Alexander von Gluck IV" <kallisti5@unixzen.com> wrote:

> $ sudo dd if=idbloader.img of=/dev/sdd seek=64
> $ sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384
> 
> Still nothing.
> 
> September 22, 2019 4:47 PM, "Michael Nazzareno Trimarchi" <michael@amarulasolutions.com> wrote:
> 
>> Hi
>> 
>> https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip/commits/master
>> 
>> make idbloader.img
>> 
>> Michael
>> 
>> On Sun, Sep 22, 2019 at 11:22 PM Alexander von Gluck IV
>> <kallisti5@unixzen.com> wrote:
> 
> Using master from git://git.denx.de/u-boot.git
> 
> commit 390183b58179ddaf986422f4d9446c596660f7e0 (HEAD -> master, origin/master, origin/HEAD)
> Merge: d6c7309f56 79907a4f84
> Author: Tom Rini <trini@konsulko.com>
> Date: Sat Sep 21 07:31:23 2019 -0400
> 
> Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
> 
> Pull request for UEFI sub-system for v2019.10-rc4 (5)
> 
> This patch set fixes errors in the UEFI sub-system and adds a function to
> compare u16 strings which is prerequisite for further patches.
> 
> Same error:
> 
> $ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin out
> Warning: SPL image is too large (size 0xb000) and will not boot
> Error: image verification failed
> 
> $ ls -lah spl/u-boot-spl-dtb.bin
> -rw-rw-r-- 1 kallisti5 kallisti5 43K Sep 22 16:17 spl/u-boot-spl-dtb.bin
> 
> September 22, 2019 4:03 PM, "Michael Nazzareno Trimarchi" <michael@amarulasolutions.com> wrote:
> 
> Hi
> 
> Please use the latest uboot. The fixes should be already merged
> 
> Mcihael
> 
> On Sun, Sep 22, 2019 at 10:53 PM Alexander von Gluck IV
> <kallisti5@unixzen.com> wrote:
> 
> Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
> 
> The docs seem to recommend:
> $ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin out
> 
> However, that produces:
> Warning: SPL image is too large (size 0xb000) and will not boot
> 
> I saw this patch to disable I2C in the SPL to reduce its size:
> https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-
> inker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patch
> 
> However, that breaks the build :-|
> 
> LD spl/u-boot-spl
> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_write':
> /tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference to `dm_i2c_write'
> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_read':
> /tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read'
> make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
> make: *** [Makefile:1762: spl/u-boot-spl] Error 2
> make: Leaving directory '/tmp/arm-build'
> Disabling SPL Power then results in an error compiling MMC support
> Any alternative methods to getting u-boot running from SD?
> Rockchip devices seem to be kind of complex to get going :-|
> -- Alex
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot
> 
> --
> | Michael Nazzareno Trimarchi Amarula Solutions BV |
> | COO - Founder Cruquiuskade 47 |
> | +31(0)851119172 Amsterdam 1018 AM NL |
> | [`as] http://www.amarulasolutions.com |
>> --
>> | Michael Nazzareno Trimarchi Amarula Solutions BV |
>> | COO - Founder Cruquiuskade 47 |
>> | +31(0)851119172 Amsterdam 1018 AM NL |
>> | [`as] http://www.amarulasolutions.com |
> 
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot

[U-Boot] rk3288 (Tinkerboard) not booting【请注意，邮件由u-boot-bounces@lists.denx.de代发】

[Kever Yang]

Hi Alexander,

     The tinker board already enable TPL, so it should be use TPL 
instead of SPL with mkimage tool.

The idbloader should have including both, if the idbloader boot fail, 
could you share the boot log?


Thanks,
- Kever
On 2019/9/23 上午5:22, Alexander von Gluck IV wrote:
> Using master from git://git.denx.de/u-boot.git
>
> commit 390183b58179ddaf986422f4d9446c596660f7e0 (HEAD -> master, origin/master, origin/HEAD)
> Merge: d6c7309f56 79907a4f84
> Author: Tom Rini <trini@konsulko.com>
> Date:   Sat Sep 21 07:31:23 2019 -0400
>
>      Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
>      
>      Pull request for UEFI sub-system for v2019.10-rc4 (5)
>      
>      This patch set fixes errors in the UEFI sub-system and adds a function to
>      compare u16 strings which is prerequisite for further patches.
>
>
> Same error:
>
>
> $ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin out
> Warning: SPL image is too large (size 0xb000) and will not boot
> Error: image verification failed
>
>
> $ ls -lah spl/u-boot-spl-dtb.bin
> -rw-rw-r-- 1 kallisti5 kallisti5 43K Sep 22 16:17 spl/u-boot-spl-dtb.bin
>
>
>
> September 22, 2019 4:03 PM, "Michael Nazzareno Trimarchi" <michael@amarulasolutions.com> wrote:
>
>> Hi
>>
>> Please use the latest uboot. The fixes should be already merged
>>
>> Mcihael
>>
>> On Sun, Sep 22, 2019 at 10:53 PM Alexander von Gluck IV
>> <kallisti5@unixzen.com> wrote:
>>
>>> Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
>>>
>>> The docs seem to recommend:
>>> $ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin out
>>>
>>> However, that produces:
>>> Warning: SPL image is too large (size 0xb000) and will not boot
>>>
>>> I saw this patch to disable I2C in the SPL to reduce its size:
>>> https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-
>>> inker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patch
>>>
>>> However, that breaks the build :-|
>>>
>>> LD spl/u-boot-spl
>>> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_write':
>>> /tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference to `dm_i2c_write'
>>> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_read':
>>> /tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read'
>>> make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
>>> make: *** [Makefile:1762: spl/u-boot-spl] Error 2
>>> make: Leaving directory '/tmp/arm-build'
>>> Disabling SPL Power then results in an error compiling MMC support
>>> Any alternative methods to getting u-boot running from SD?
>>> Rockchip devices seem to be kind of complex to get going :-|
>>> -- Alex
>>> _______________________________________________
>>> U-Boot mailing list
>>> U-Boot at lists.denx.de
>>> https://lists.denx.de/listinfo/u-boot
>> --
>> | Michael Nazzareno Trimarchi Amarula Solutions BV |
>> | COO - Founder Cruquiuskade 47 |
>> | +31(0)851119172 Amsterdam 1018 AM NL |
>> | [`as] http://www.amarulasolutions.com |
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot

[U-Boot] rk3288 (Tinkerboard) not booting【请注意，邮件由u-boot-bounces@lists.denx.de代发】

[Alexander von Gluck IV]

Hello!

There is no uart output and no video with u-boot master.
The board works as expected booting the Asus Armbian image on an SD.

At this point i'd be happy to get some u-boot uart output :-)

 -- Alex


September 22, 2019 8:04 PM, "Kever Yang" <kever.yang@rock-chips.com> wrote:

> Hi Alexander,
> 
> The tinker board already enable TPL, so it should be use TPL instead of SPL with mkimage tool.
> 
> The idbloader should have including both, if the idbloader boot fail, could you share the boot log?
> 
> Thanks,
> - Kever
> On 2019/9/23 上午5:22, Alexander von Gluck IV wrote:
> 
>> Using master from git://git.denx.de/u-boot.git
>> 
>> commit 390183b58179ddaf986422f4d9446c596660f7e0 (HEAD -> master, origin/master, origin/HEAD)
>> Merge: d6c7309f56 79907a4f84
>> Author: Tom Rini <trini@konsulko.com>
>> Date: Sat Sep 21 07:31:23 2019 -0400
>> 
>> Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
>>> Pull request for UEFI sub-system for v2019.10-rc4 (5)
>>> This patch set fixes errors in the UEFI sub-system and adds a function to
>> compare u16 strings which is prerequisite for further patches.
>> 
>> Same error:
>> 
>> $ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin out
>> Warning: SPL image is too large (size 0xb000) and will not boot
>> Error: image verification failed
>> 
>> $ ls -lah spl/u-boot-spl-dtb.bin
>> -rw-rw-r-- 1 kallisti5 kallisti5 43K Sep 22 16:17 spl/u-boot-spl-dtb.bin
>> 
>> September 22, 2019 4:03 PM, "Michael Nazzareno Trimarchi" <michael@amarulasolutions.com> wrote:
>> 
>>> Hi
>>> 
>>> Please use the latest uboot. The fixes should be already merged
>>> 
>>> Mcihael
>>> 
>>> On Sun, Sep 22, 2019 at 10:53 PM Alexander von Gluck IV
>>> <kallisti5@unixzen.com> wrote:
>> 
>> Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
>> 
>> The docs seem to recommend:
>> $ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin out
>> 
>> However, that produces:
>> Warning: SPL image is too large (size 0xb000) and will not boot
>> 
>> I saw this patch to disable I2C in the SPL to reduce its size:
>> https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-
>> inker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patch
>> 
>> However, that breaks the build :-|
>> 
>> LD spl/u-boot-spl
>> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_write':
>> /tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference to `dm_i2c_write'
>> arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_read':
>> /tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read'
>> make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
>> make: *** [Makefile:1762: spl/u-boot-spl] Error 2
>> make: Leaving directory '/tmp/arm-build'
>> Disabling SPL Power then results in an error compiling MMC support
>> Any alternative methods to getting u-boot running from SD?
>> Rockchip devices seem to be kind of complex to get going :-|
>> -- Alex
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> https://lists.denx.de/listinfo/u-boot
>>> --
>>> | Michael Nazzareno Trimarchi Amarula Solutions BV |
>>> | COO - Founder Cruquiuskade 47 |
>>> | +31(0)851119172 Amsterdam 1018 AM NL |
>>> | [`as] http://www.amarulasolutions.com |
>> 
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> https://lists.denx.de/listinfo/u-boot

[U-Boot] rk3288 (Tinkerboard) not booting【请注意，邮件由u-boot-bounces@lists.denx.de代发】

[Jonathan Gray]

On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
> Hello!
> 
> There is no uart output and no video with u-boot master.
> The board works as expected booting the Asus Armbian image on an SD.
> 
> At this point i'd be happy to get some u-boot uart output :-)
> 
>  -- Alex

uart output works here with the latest master
(780a17e814503f71d1b51d578b32bc9c89933183)

U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20)
Trying to boot from BOOTROM
Returning to boot ROM...

U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
Trying to boot from MMC1


U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)

Model: Tinker-RK3288
DRAM:  2 GiB
MMC:   dwmmc at ff0c0000: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Model: Tinker-RK3288
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
Net:   eth0: ethernet at ff290000
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found EFI removable media binary efi/boot/bootarm.efi
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Scanning disk dwmmc at ff0c0000.blk...
Found 3 disks
BootOrder not defined
EFI boot manager: Cannot load any image
88176 bytes read in 9 ms (9.3 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>> OpenBSD/armv7 BOOTARM 1.6
boot>

[U-Boot] rk3288 (Tinkerboard) not booting【请注意，邮件由u-boot-bounces@lists.denx.de代发】

[Alexander von Gluck IV]

Ok, looking for differences now..

* Older Tinker Board?  (I'm not using the Tinker Board S)
* Same steps?
* Same config?  tinker-rk3288_defconfig?
* Uart 115200?
* Any HDMI Video output?
* GCC version?

September 23, 2019 12:34 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:

> On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
> 
>> Hello!
>> 
>> There is no uart output and no video with u-boot master.
>> The board works as expected booting the Asus Armbian image on an SD.
>> 
>> At this point i'd be happy to get some u-boot uart output :-)
>> 
>> -- Alex
> 
> uart output works here with the latest master
> (780a17e814503f71d1b51d578b32bc9c89933183)
> 
> U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20)
> Trying to boot from BOOTROM
> Returning to boot ROM...
> 
> U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
> Trying to boot from MMC1
> 
> U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
> 
> Model: Tinker-RK3288
> DRAM: 2 GiB
> MMC: dwmmc at ff0c0000: 1
> Loading Environment from MMC... *** Warning - bad CRC, using default environment
> 
> In: serial
> Out: serial
> Err: serial
> Model: Tinker-RK3288
> rockchip_dnl_key_pressed: adc_channel_single_shot fail!
> Net: eth0: ethernet at ff290000
> Hit any key to stop autoboot: 0
> switch to partitions #0, OK
> mmc1 is current device
> Scanning mmc 1:1...
> Found EFI removable media binary efi/boot/bootarm.efi
> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> Scanning disk dwmmc at ff0c0000.blk...
> Found 3 disks
> BootOrder not defined
> EFI boot manager: Cannot load any image
> 88176 bytes read in 9 ms (9.3 MiB/s)
> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>>> OpenBSD/armv7 BOOTARM 1.6
> 
> boot>

[U-Boot] rk3288 (Tinkerboard) not booting【请注意，邮件由u-boot-bounces@lists.denx.de代发】

[Jonathan Gray]

On Mon, Sep 23, 2019 at 01:06:35PM +0000, Alexander von Gluck IV wrote:
> Ok, looking for differences now..
> 
> * Older Tinker Board?  (I'm not using the Tinker Board S)

yes, the original one

> * Same steps?

along the lines of

gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig
gmake CROSS_COMPILE="arm-none-eabi-" all
tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
    cat spl/u-boot-spl-dtb.bin >> idbloader.img

> * Same config?  tinker-rk3288_defconfig?

yes

> * Uart 115200?

yes

> * Any HDMI Video output?

no hdmi connected only serial

> * GCC version?

gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target

> 
> September 23, 2019 12:34 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
> 
> > On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
> > 
> >> Hello!
> >> 
> >> There is no uart output and no video with u-boot master.
> >> The board works as expected booting the Asus Armbian image on an SD.
> >> 
> >> At this point i'd be happy to get some u-boot uart output :-)
> >> 
> >> -- Alex
> > 
> > uart output works here with the latest master
> > (780a17e814503f71d1b51d578b32bc9c89933183)
> > 
> > U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20)
> > Trying to boot from BOOTROM
> > Returning to boot ROM...
> > 
> > U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
> > Trying to boot from MMC1
> > 
> > U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
> > 
> > Model: Tinker-RK3288
> > DRAM: 2 GiB
> > MMC: dwmmc at ff0c0000: 1
> > Loading Environment from MMC... *** Warning - bad CRC, using default environment
> > 
> > In: serial
> > Out: serial
> > Err: serial
> > Model: Tinker-RK3288
> > rockchip_dnl_key_pressed: adc_channel_single_shot fail!
> > Net: eth0: ethernet at ff290000
> > Hit any key to stop autoboot: 0
> > switch to partitions #0, OK
> > mmc1 is current device
> > Scanning mmc 1:1...
> > Found EFI removable media binary efi/boot/bootarm.efi
> > libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> > Scanning disk dwmmc at ff0c0000.blk...
> > Found 3 disks
> > BootOrder not defined
> > EFI boot manager: Cannot load any image
> > 88176 bytes read in 9 ms (9.3 MiB/s)
> > libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> >>> OpenBSD/armv7 BOOTARM 1.6
> > 
> > boot>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot

[U-Boot] rk3288 (Tinkerboard) not booting【请注意，邮件由u-boot-bounces@lists.denx.de代发】

[Alexander von Gluck IV]

Oh, a difference:

$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
    cat spl/u-boot-spl-dtb.bin >> idbloader.img

I'm using the idbloader.img that u-boot automatically spits out.

$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader-manual.img
Image Type:   Rockchip RK32 (SD/MMC) boot image
Data Size:    20480 bytes
$ cat spl/u-boot-spl-dtb.bin >> idbloader-manual.img

However.. the generated idbloader-manual.img from the commands above is identical to idbloader.img
that u-boot produces compared with md5sum.


Are you writing the following?

  sudo dd if=idbloader.img of=/dev/sdd seek=64
  sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384

(where /dev/sdd is a MicroSD card)

These should be enough to get into u-boot at startup... correct?

I'm not missing some requirement of u-boot.bin on a FAT32 partition or something?

 -- Alex

September 23, 2019 8:31 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:

> On Mon, Sep 23, 2019 at 01:06:35PM +0000, Alexander von Gluck IV wrote:
> 
>> Ok, looking for differences now..
>> 
>> * Older Tinker Board? (I'm not using the Tinker Board S)
> 
> yes, the original one
> 
>> * Same steps?
> 
> along the lines of
> 
> gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig
> gmake CROSS_COMPILE="arm-none-eabi-" all
> tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
> cat spl/u-boot-spl-dtb.bin >> idbloader.img
> 
>> * Same config? tinker-rk3288_defconfig?
> 
> yes
> 
>> * Uart 115200?
> 
> yes
> 
>> * Any HDMI Video output?
> 
> no hdmi connected only serial
> 
>> * GCC version?
> 
> gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target
> 
>> September 23, 2019 12:34 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
>> 
>> On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
>> 
>> Hello!
>> 
>> There is no uart output and no video with u-boot master.
>> The board works as expected booting the Asus Armbian image on an SD.
>> 
>> At this point i'd be happy to get some u-boot uart output :-)
>> 
>> -- Alex
>> 
>> uart output works here with the latest master
>> (780a17e814503f71d1b51d578b32bc9c89933183)
>> 
>> U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20)
>> Trying to boot from BOOTROM
>> Returning to boot ROM...
>> 
>> U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
>> Trying to boot from MMC1
>> 
>> U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
>> 
>> Model: Tinker-RK3288
>> DRAM: 2 GiB
>> MMC: dwmmc at ff0c0000: 1
>> Loading Environment from MMC... *** Warning - bad CRC, using default environment
>> 
>> In: serial
>> Out: serial
>> Err: serial
>> Model: Tinker-RK3288
>> rockchip_dnl_key_pressed: adc_channel_single_shot fail!
>> Net: eth0: ethernet at ff290000
>> Hit any key to stop autoboot: 0
>> switch to partitions #0, OK
>> mmc1 is current device
>> Scanning mmc 1:1...
>> Found EFI removable media binary efi/boot/bootarm.efi
>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>> Scanning disk dwmmc at ff0c0000.blk...
>> Found 3 disks
>> BootOrder not defined
>> EFI boot manager: Cannot load any image
>> 88176 bytes read in 9 ms (9.3 MiB/s)
>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>> OpenBSD/armv7 BOOTARM 1.6
>> 
>> boot>
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> https://lists.denx.de/listinfo/u-boot

[U-Boot] rk3288 (Tinkerboard) not booting【请注意，邮件由u-boot-bounces@lists.denx.de代发】

[Jonathan Gray]

On Mon, Sep 23, 2019 at 01:55:32PM +0000, Alexander von Gluck IV wrote:
> Oh, a difference:
> 
> $ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
>     cat spl/u-boot-spl-dtb.bin >> idbloader.img
> 
> I'm using the idbloader.img that u-boot automatically spits out.
> 
> $ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader-manual.img
> Image Type:   Rockchip RK32 (SD/MMC) boot image
> Data Size:    20480 bytes
> $ cat spl/u-boot-spl-dtb.bin >> idbloader-manual.img
> 
> However.. the generated idbloader-manual.img from the commands above is identical to idbloader.img
> that u-boot produces compared with md5sum.
> 
> 
> Are you writing the following?
> 
>   sudo dd if=idbloader.img of=/dev/sdd seek=64
>   sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384

those files/offsets yes

> 
> (where /dev/sdd is a MicroSD card)
> 
> These should be enough to get into u-boot at startup... correct?

yes

I am using uart2
https://www.asus.com/us/Single-Board-Computer/Tinker-Board/
32 UART2TX_PWM3
33 UART2RX_PWM2
and 30 for ground

> 
> I'm not missing some requirement of u-boot.bin on a FAT32 partition or something?

the tpl/spl and u-boot proper are at raw offsets in this case

> 
>  -- Alex
> 
> September 23, 2019 8:31 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
> 
> > On Mon, Sep 23, 2019 at 01:06:35PM +0000, Alexander von Gluck IV wrote:
> > 
> >> Ok, looking for differences now..
> >> 
> >> * Older Tinker Board? (I'm not using the Tinker Board S)
> > 
> > yes, the original one
> > 
> >> * Same steps?
> > 
> > along the lines of
> > 
> > gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig
> > gmake CROSS_COMPILE="arm-none-eabi-" all
> > tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
> > cat spl/u-boot-spl-dtb.bin >> idbloader.img
> > 
> >> * Same config? tinker-rk3288_defconfig?
> > 
> > yes
> > 
> >> * Uart 115200?
> > 
> > yes
> > 
> >> * Any HDMI Video output?
> > 
> > no hdmi connected only serial
> > 
> >> * GCC version?
> > 
> > gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target
> > 
> >> September 23, 2019 12:34 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
> >> 
> >> On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
> >> 
> >> Hello!
> >> 
> >> There is no uart output and no video with u-boot master.
> >> The board works as expected booting the Asus Armbian image on an SD.
> >> 
> >> At this point i'd be happy to get some u-boot uart output :-)
> >> 
> >> -- Alex
> >> 
> >> uart output works here with the latest master
> >> (780a17e814503f71d1b51d578b32bc9c89933183)
> >> 
> >> U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20)
> >> Trying to boot from BOOTROM
> >> Returning to boot ROM...
> >> 
> >> U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
> >> Trying to boot from MMC1
> >> 
> >> U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
> >> 
> >> Model: Tinker-RK3288
> >> DRAM: 2 GiB
> >> MMC: dwmmc at ff0c0000: 1
> >> Loading Environment from MMC... *** Warning - bad CRC, using default environment
> >> 
> >> In: serial
> >> Out: serial
> >> Err: serial
> >> Model: Tinker-RK3288
> >> rockchip_dnl_key_pressed: adc_channel_single_shot fail!
> >> Net: eth0: ethernet at ff290000
> >> Hit any key to stop autoboot: 0
> >> switch to partitions #0, OK
> >> mmc1 is current device
> >> Scanning mmc 1:1...
> >> Found EFI removable media binary efi/boot/bootarm.efi
> >> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> >> Scanning disk dwmmc at ff0c0000.blk...
> >> Found 3 disks
> >> BootOrder not defined
> >> EFI boot manager: Cannot load any image
> >> 88176 bytes read in 9 ms (9.3 MiB/s)
> >> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> >> OpenBSD/armv7 BOOTARM 1.6
> >> 
> >> boot>
> >> _______________________________________________
> >> U-Boot mailing list
> >> U-Boot at lists.denx.de
> >> https://lists.denx.de/listinfo/u-boot

[U-Boot] rk3288 (Tinkerboard) not booting【请注意，邮件由u-boot-bounces@lists.denx.de代发】

[Alexander von Gluck IV]

ACK! I'm on UART1. Mix that with video potentially not working
in u-boot and I think I have my answer.

I'll test this afternoon.

(PS, since the Tinker is supposed to be "Raspberry Pi like", why would
u-boot present on UART2 on it while the Raspberry Pi u-boot uses UART1?)


Thanks for the help!

 -- Alex


September 23, 2019 9:19 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:

> On Mon, Sep 23, 2019 at 01:55:32PM +0000, Alexander von Gluck IV wrote:
> 
>> Oh, a difference:
>> 
>> $ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
>> cat spl/u-boot-spl-dtb.bin >> idbloader.img
>> 
>> I'm using the idbloader.img that u-boot automatically spits out.
>> 
>> $ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader-manual.img
>> Image Type: Rockchip RK32 (SD/MMC) boot image
>> Data Size: 20480 bytes
>> $ cat spl/u-boot-spl-dtb.bin >> idbloader-manual.img
>> 
>> However.. the generated idbloader-manual.img from the commands above is identical to idbloader.img
>> that u-boot produces compared with md5sum.
>> 
>> Are you writing the following?
>> 
>> sudo dd if=idbloader.img of=/dev/sdd seek=64
>> sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384
> 
> those files/offsets yes
> 
>> (where /dev/sdd is a MicroSD card)
>> 
>> These should be enough to get into u-boot at startup... correct?
> 
> yes
> 
> I am using uart2
> https://www.asus.com/us/Single-Board-Computer/Tinker-Board
> 32 UART2TX_PWM3
> 33 UART2RX_PWM2
> and 30 for ground
> 
>> I'm not missing some requirement of u-boot.bin on a FAT32 partition or something?
> 
> the tpl/spl and u-boot proper are at raw offsets in this case
> 
>> -- Alex
>> 
>> September 23, 2019 8:31 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
>> 
>> On Mon, Sep 23, 2019 at 01:06:35PM +0000, Alexander von Gluck IV wrote:
>> 
>> Ok, looking for differences now..
>> 
>> * Older Tinker Board? (I'm not using the Tinker Board S)
>> 
>> yes, the original one
>> 
>> * Same steps?
>> 
>> along the lines of
>> 
>> gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig
>> gmake CROSS_COMPILE="arm-none-eabi-" all
>> tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
>> cat spl/u-boot-spl-dtb.bin >> idbloader.img
>> 
>> * Same config? tinker-rk3288_defconfig?
>> 
>> yes
>> 
>> * Uart 115200?
>> 
>> yes
>> 
>> * Any HDMI Video output?
>> 
>> no hdmi connected only serial
>> 
>> * GCC version?
>> 
>> gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target
>> 
>> September 23, 2019 12:34 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
>> 
>> On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
>> 
>> Hello!
>> 
>> There is no uart output and no video with u-boot master.
>> The board works as expected booting the Asus Armbian image on an SD.
>> 
>> At this point i'd be happy to get some u-boot uart output :-)
>> 
>> -- Alex
>> 
>> uart output works here with the latest master
>> (780a17e814503f71d1b51d578b32bc9c89933183)
>> 
>> U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20)
>> Trying to boot from BOOTROM
>> Returning to boot ROM...
>> 
>> U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
>> Trying to boot from MMC1
>> 
>> U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
>> 
>> Model: Tinker-RK3288
>> DRAM: 2 GiB
>> MMC: dwmmc at ff0c0000: 1
>> Loading Environment from MMC... *** Warning - bad CRC, using default environment
>> 
>> In: serial
>> Out: serial
>> Err: serial
>> Model: Tinker-RK3288
>> rockchip_dnl_key_pressed: adc_channel_single_shot fail!
>> Net: eth0: ethernet at ff290000
>> Hit any key to stop autoboot: 0
>> switch to partitions #0, OK
>> mmc1 is current device
>> Scanning mmc 1:1...
>> Found EFI removable media binary efi/boot/bootarm.efi
>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>> Scanning disk dwmmc at ff0c0000.blk...
>> Found 3 disks
>> BootOrder not defined
>> EFI boot manager: Cannot load any image
>> 88176 bytes read in 9 ms (9.3 MiB/s)
>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>> OpenBSD/armv7 BOOTARM 1.6
>> 
>> boot>
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> https://lists.denx.de/listinfo/u-boot

[U-Boot] rk3288 (Tinkerboard) not booting【请注意，邮件由u-boot-bounces@lists.denx.de代发】

[Alexander von Gluck IV]

Just rounding this one out.. I was definitely looking at the wrong uart. After
moving to uart2, things are working as expected (minus hdmi output from u-boot)

Thanks!

 -- Alex

September 23, 2019 9:27 AM, "Alexander von Gluck IV" <kallisti5@unixzen.com> wrote:
> ACK! I'm on UART1. Mix that with video potentially not working
> in u-boot and I think I have my answer.
> 
> I'll test this afternoon.
> 
> (PS, since the Tinker is supposed to be "Raspberry Pi like", why would
> u-boot present on UART2 on it while the Raspberry Pi u-boot uses UART1?)
> 
> Thanks for the help!
> 
> -- Alex
> 
> September 23, 2019 9:19 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
> 
>> On Mon, Sep 23, 2019 at 01:55:32PM +0000, Alexander von Gluck IV wrote:
>> 
>>> Oh, a difference:
>>> 
>>> $ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
>>> cat spl/u-boot-spl-dtb.bin >> idbloader.img
>>> 
>>> I'm using the idbloader.img that u-boot automatically spits out.
>>> 
>>> $ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader-manual.img
>>> Image Type: Rockchip RK32 (SD/MMC) boot image
>>> Data Size: 20480 bytes
>>> $ cat spl/u-boot-spl-dtb.bin >> idbloader-manual.img
>>> 
>>> However.. the generated idbloader-manual.img from the commands above is identical to idbloader.img
>>> that u-boot produces compared with md5sum.
>>> 
>>> Are you writing the following?
>>> 
>>> sudo dd if=idbloader.img of=/dev/sdd seek=64
>>> sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384
>> 
>> those files/offsets yes
>> 
>>> (where /dev/sdd is a MicroSD card)
>>> 
>>> These should be enough to get into u-boot at startup... correct?
>> 
>> yes
>> 
>> I am using uart2
>> https://www.asus.com/us/Single-Board-Computer/Tinker-Board
>> 32 UART2TX_PWM3
>> 33 UART2RX_PWM2
>> and 30 for ground
>> 
>>> I'm not missing some requirement of u-boot.bin on a FAT32 partition or something?
>> 
>> the tpl/spl and u-boot proper are at raw offsets in this case
>> 
>>> -- Alex
>>> 
>>> September 23, 2019 8:31 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
>>> 
>>> On Mon, Sep 23, 2019 at 01:06:35PM +0000, Alexander von Gluck IV wrote:
>>> 
>>> Ok, looking for differences now..
>>> 
>>> * Older Tinker Board? (I'm not using the Tinker Board S)
>>> 
>>> yes, the original one
>>> 
>>> * Same steps?
>>> 
>>> along the lines of
>>> 
>>> gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig
>>> gmake CROSS_COMPILE="arm-none-eabi-" all
>>> tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
>>> cat spl/u-boot-spl-dtb.bin >> idbloader.img
>>> 
>>> * Same config? tinker-rk3288_defconfig?
>>> 
>>> yes
>>> 
>>> * Uart 115200?
>>> 
>>> yes
>>> 
>>> * Any HDMI Video output?
>>> 
>>> no hdmi connected only serial
>>> 
>>> * GCC version?
>>> 
>>> gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target
>>> 
>>> September 23, 2019 12:34 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
>>> 
>>> On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
>>> 
>>> Hello!
>>> 
>>> There is no uart output and no video with u-boot master.
>>> The board works as expected booting the Asus Armbian image on an SD.
>>> 
>>> At this point i'd be happy to get some u-boot uart output :-)
>>> 
>>> -- Alex
>>> 
>>> uart output works here with the latest master
>>> (780a17e814503f71d1b51d578b32bc9c89933183)
>>> 
>>> U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20)
>>> Trying to boot from BOOTROM
>>> Returning to boot ROM...
>>> 
>>> U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
>>> Trying to boot from MMC1
>>> 
>>> U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
>>> 
>>> Model: Tinker-RK3288
>>> DRAM: 2 GiB
>>> MMC: dwmmc at ff0c0000: 1
>>> Loading Environment from MMC... *** Warning - bad CRC, using default environment
>>> 
>>> In: serial
>>> Out: serial
>>> Err: serial
>>> Model: Tinker-RK3288
>>> rockchip_dnl_key_pressed: adc_channel_single_shot fail!
>>> Net: eth0: ethernet at ff290000
>>> Hit any key to stop autoboot: 0
>>> switch to partitions #0, OK
>>> mmc1 is current device
>>> Scanning mmc 1:1...
>>> Found EFI removable media binary efi/boot/bootarm.efi
>>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>>> Scanning disk dwmmc at ff0c0000.blk...
>>> Found 3 disks
>>> BootOrder not defined
>>> EFI boot manager: Cannot load any image
>>> 88176 bytes read in 9 ms (9.3 MiB/s)
>>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>>> OpenBSD/armv7 BOOTARM 1.6
>>> 
>>> boot>
>>> _______________________________________________
>>> U-Boot mailing list
>>> U-Boot at lists.denx.de
>>> https://lists.denx.de/listinfo/u-boot
> 
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot

[U-Boot] rk3288 (Tinkerboard) not booting【请注意，邮件由u-boot-bounces@lists.denx.de代发】

[Michael Nazzareno Trimarchi]

Hi

On Wed, Sep 25, 2019 at 8:19 PM Alexander von Gluck IV
<kallisti5@unixzen.com> wrote:
>
> Just rounding this one out.. I was definitely looking at the wrong uart. After
> moving to uart2, things are working as expected (minus hdmi output from u-boot)

This can be enabled, but it's not the default on tinker

Michael

>
> Thanks!
>
>  -- Alex
>
> September 23, 2019 9:27 AM, "Alexander von Gluck IV" <kallisti5@unixzen.com> wrote:
> > ACK! I'm on UART1. Mix that with video potentially not working
> > in u-boot and I think I have my answer.
> >
> > I'll test this afternoon.
> >
> > (PS, since the Tinker is supposed to be "Raspberry Pi like", why would
> > u-boot present on UART2 on it while the Raspberry Pi u-boot uses UART1?)
> >
> > Thanks for the help!
> >
> > -- Alex
> >
> > September 23, 2019 9:19 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
> >
> >> On Mon, Sep 23, 2019 at 01:55:32PM +0000, Alexander von Gluck IV wrote:
> >>
> >>> Oh, a difference:
> >>>
> >>> $ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
> >>> cat spl/u-boot-spl-dtb.bin >> idbloader.img
> >>>
> >>> I'm using the idbloader.img that u-boot automatically spits out.
> >>>
> >>> $ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader-manual.img
> >>> Image Type: Rockchip RK32 (SD/MMC) boot image
> >>> Data Size: 20480 bytes
> >>> $ cat spl/u-boot-spl-dtb.bin >> idbloader-manual.img
> >>>
> >>> However.. the generated idbloader-manual.img from the commands above is identical to idbloader.img
> >>> that u-boot produces compared with md5sum.
> >>>
> >>> Are you writing the following?
> >>>
> >>> sudo dd if=idbloader.img of=/dev/sdd seek=64
> >>> sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384
> >>
> >> those files/offsets yes
> >>
> >>> (where /dev/sdd is a MicroSD card)
> >>>
> >>> These should be enough to get into u-boot at startup... correct?
> >>
> >> yes
> >>
> >> I am using uart2
> >> https://www.asus.com/us/Single-Board-Computer/Tinker-Board
> >> 32 UART2TX_PWM3
> >> 33 UART2RX_PWM2
> >> and 30 for ground
> >>
> >>> I'm not missing some requirement of u-boot.bin on a FAT32 partition or something?
> >>
> >> the tpl/spl and u-boot proper are at raw offsets in this case
> >>
> >>> -- Alex
> >>>
> >>> September 23, 2019 8:31 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
> >>>
> >>> On Mon, Sep 23, 2019 at 01:06:35PM +0000, Alexander von Gluck IV wrote:
> >>>
> >>> Ok, looking for differences now..
> >>>
> >>> * Older Tinker Board? (I'm not using the Tinker Board S)
> >>>
> >>> yes, the original one
> >>>
> >>> * Same steps?
> >>>
> >>> along the lines of
> >>>
> >>> gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig
> >>> gmake CROSS_COMPILE="arm-none-eabi-" all
> >>> tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
> >>> cat spl/u-boot-spl-dtb.bin >> idbloader.img
> >>>
> >>> * Same config? tinker-rk3288_defconfig?
> >>>
> >>> yes
> >>>
> >>> * Uart 115200?
> >>>
> >>> yes
> >>>
> >>> * Any HDMI Video output?
> >>>
> >>> no hdmi connected only serial
> >>>
> >>> * GCC version?
> >>>
> >>> gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target
> >>>
> >>> September 23, 2019 12:34 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:
> >>>
> >>> On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
> >>>
> >>> Hello!
> >>>
> >>> There is no uart output and no video with u-boot master.
> >>> The board works as expected booting the Asus Armbian image on an SD.
> >>>
> >>> At this point i'd be happy to get some u-boot uart output :-)
> >>>
> >>> -- Alex
> >>>
> >>> uart output works here with the latest master
> >>> (780a17e814503f71d1b51d578b32bc9c89933183)
> >>>
> >>> U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20)
> >>> Trying to boot from BOOTROM
> >>> Returning to boot ROM...
> >>>
> >>> U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
> >>> Trying to boot from MMC1
> >>>
> >>> U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
> >>>
> >>> Model: Tinker-RK3288
> >>> DRAM: 2 GiB
> >>> MMC: dwmmc at ff0c0000: 1
> >>> Loading Environment from MMC... *** Warning - bad CRC, using default environment
> >>>
> >>> In: serial
> >>> Out: serial
> >>> Err: serial
> >>> Model: Tinker-RK3288
> >>> rockchip_dnl_key_pressed: adc_channel_single_shot fail!
> >>> Net: eth0: ethernet at ff290000
> >>> Hit any key to stop autoboot: 0
> >>> switch to partitions #0, OK
> >>> mmc1 is current device
> >>> Scanning mmc 1:1...
> >>> Found EFI removable media binary efi/boot/bootarm.efi
> >>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> >>> Scanning disk dwmmc at ff0c0000.blk...
> >>> Found 3 disks
> >>> BootOrder not defined
> >>> EFI boot manager: Cannot load any image
> >>> 88176 bytes read in 9 ms (9.3 MiB/s)
> >>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> >>> OpenBSD/armv7 BOOTARM 1.6
> >>>
> >>> boot>
> >>> _______________________________________________
> >>> U-Boot mailing list
> >>> U-Boot at lists.denx.de
> >>> https://lists.denx.de/listinfo/u-boot
> >
> > _______________________________________________
> > U-Boot mailing list
> > U-Boot at lists.denx.de
> > https://lists.denx.de/listinfo/u-boot
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot



-- 
| Michael Nazzareno Trimarchi                     Amarula Solutions BV |
| COO  -  Founder                                      Cruquiuskade 47 |
| +31(0)851119172                                 Amsterdam 1018 AM NL |
|                  [`as] http://www.amarulasolutions.com               |