Linux version 2.6.21-2952.fc8xen (kojibuilder@hammer2.fedora.redhat.com) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33)) #1 SMP Mon Nov 19 07:06:55 EST 2007 BIOS-provided physical RAM map: sanitize start sanitize bail 0 copy_e820_map() start: 0000000000000000 size: 000000007491e000 end: 000000007491e000 type: 1 Xen: 0000000000000000 - 000000007491e000 (usable) 1137MB HIGHMEM available. 727MB LOWMEM available. NX (Execute Disable) protection: active Entering add_active_range(0, 0, 477470) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 186366 Normal 186366 -> 186366 HighMem 186366 -> 477470 early_node_map[1] active PFN ranges 0: 0 -> 477470 On node 0 totalpages: 477470 DMA zone: 1455 pages used for memmap DMA zone: 0 pages reserved DMA zone: 184911 pages, LIFO batch:31 Normal zone: 0 pages used for memmap HighMem zone: 2274 pages used for memmap HighMem zone: 288830 pages, LIFO batch:31 found SMP MP-table at 000ff780 DMI present. ACPI: RSDP 000F9990, 0014 (r0 ACPIAM) ACPI: RSDT 7D6B0000, 0044 (r1 A M I OEMRSDT 5000708 MSFT 97) ACPI: FACP 7D6B0200, 0084 (r2 A M I OEMFACP 5000708 MSFT 97) ACPI Warning (tbfadt-0360): Ignoring BIOS FADT r2 C-state control [20070126] ACPI: DSDT 7D6B0490, 6643 (r1 SDBLI9 SDBLI944 44 INTL 20051117) ACPI: FACS 7D6BE000, 0040 ACPI: APIC 7D6B0390, 006C (r1 A M I OEMAPIC 5000708 MSFT 97) ACPI: MCFG 7D6B0450, 003C (r1 A M I OEMMCFG 5000708 MSFT 97) ACPI: OEMB 7D6BE040, 0079 (r1 A M I AMI_OEM 5000708 MSFT 97) ACPI: ASF! 7D6B6AE0, 0099 (r32 LEGEND I865PASF 1 INTL 20051117) ACPI: GSCI 7D6BE0C0, 2024 (r1 A M I GMCHSCI 5000708 MSFT 97) ACPI: iEIT 7D6C00F0, 00B0 (r1 A M I EITTABLE 5000708 MSFT 97) ACPI: SSDT 7D6C0BC0, 0877 (r1 DpgPmm CpuPm 12 INTL 20051117) ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Detected 2992.804 MHz processor. Built 1 zonelists. Total pages: 473741 Kernel command line: ro root=/dev/xeni/fedora32 console=tty1 xencons=xvc0 console=xvc0 panic=30 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 CPU 0 irqstacks, hard=c136c000 soft=c134c000 PID hash table entries: 4096 (order: 12, 16384 bytes) Xen reported: 2992.594 MHz processor. Console: colour VGA+ 80x50 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Software IO TLB enabled: Aperture: 2 megabytes Kernel range: c033c000 - c053c000 Address size: 24 bits vmalloc area: ee000000-f4ffe000, maxmem 2d7fe000 Memory: 1866468k/1909880k available (2071k kernel code, 34068k reserved, 1080k data, 188k init, 1164416k highmem) virtual kernel memory layout: fixmap : 0xf5315000 - 0xf57fe000 (5028 kB) pkmap : 0xf5000000 - 0xf5200000 (2048 kB) vmalloc : 0xee000000 - 0xf4ffe000 ( 111 MB) lowmem : 0xc0000000 - 0xed7fe000 ( 727 MB) .init : 0xc1319000 - 0xc1348000 ( 188 kB) .data : 0xc1205e5e - 0xc1313fd4 (1080 kB) .text : 0xc1000000 - 0xc1205e5e (2071 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5991.67 BogoMIPS (lpj=11983344) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebd3f1 20100000 00000000 00000000 0000e3fd 00000000 00000001 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: After all inits, caps: bfebd3f1 20100000 00000000 00003940 0000e3fd 00000000 00000001 Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20070126 CPU 1 irqstacks, hard=c136d000 soft=c134d000 ENABLING IO-APIC IRQs SMP alternatives: switching to SMP code Brought up 2 CPUs Initializing CPU#1 sizeof(vma)=88 bytes sizeof(page)=32 bytes sizeof(inode)=336 bytes sizeof(dentry)=132 bytes sizeof(ext3inode)=488 bytes sizeof(buffer_head)=56 bytes sizeof(skbuff)=176 bytes sizeof(task_struct)=1376 bytes migration_cost=19 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 Setting up standard PCI resources Allocating PCI resources starting at 80000000 (gap: 7d6b0000:82950000) ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing Error attaching device data Error attaching device data Error attaching device data Error attaching device data ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:00:02.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 12 14 *15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 12 *14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 12 14 *15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 23 devices xen_mem: Initialising balloon driver. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default pnp: 00:01: iomem range 0xfed14000-0xfed19fff has been reserved pnp: 00:0a: ioport range 0xa20-0xa3f has been reserved pnp: 00:0a: ioport range 0xa00-0xa0f has been reserved pnp: 00:0a: ioport range 0xa10-0xa1f has been reserved pnp: 00:0a: ioport range 0xa40-0xa5f has been reserved pnp: 00:0b: iomem range 0xfed1c000-0xfed1ffff has been reserved pnp: 00:0b: iomem range 0xfed20000-0xfed8ffff has been reserved pnp: 00:0e: iomem range 0xffc00000-0xffefffff has been reserved pnp: 00:0f: iomem range 0xfec00000-0xfec00fff has been reserved pnp: 00:0f: iomem range 0xfee00000-0xfee00fff has been reserved pnp: 00:10: iomem range 0xe0000000-0xefffffff has been reserved pnp: 00:11: iomem range 0xffa77000-0xffa77fff has been reserved pnp: 00:12: iomem range 0x0-0x0 could not be reserved pnp: 00:13: iomem range 0x0-0x0 could not be reserved pnp: 00:14: iomem range 0x0-0x0 could not be reserved pnp: 00:15: iomem range 0x0-0x0 could not be reserved pnp: 00:16: iomem range 0x0-0x9ffff could not be reserved pnp: 00:16: iomem range 0xc0000-0xcffff could not be reserved pnp: 00:16: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:16: iomem range 0x100000-0x7d6fffff could not be reserved PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0 PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:02:00.0 IO window: disabled. MEM window: ff600000-ff6fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.2 IO window: disabled. MEM window: ff600000-ff6fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.2 to 64 PCI: Setting latency timer of device 0000:02:00.0 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 8554k freed audit: initializing netlink socket (disabled) audit(1196713193.812:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks ksign: Installing public key data Loading keyring io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] PCI: Setting latency timer of device 0000:00:1c.2 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.2:pcie00] Allocate Port Service[0000:00:1c.2:pcie02] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI Warning (tbutils-0158): Incorrect checksum in table [OEMB] - 5E, should be 4F [20070126] ACPI: SSDT 7D6C01A0, 02F4 (r1 DpgPmm P001Ist 11 INTL 20051117) Monitor-Mwait will be used to enter C-1 state ACPI: CPU0 (power states: C1[C1] C2[C2]) ACPI: SSDT 7D6C06B0, 02F4 (r1 DpgPmm P002Ist 12 INTL 20051117) ACPI: CPU1 (power states: C1[C1] C2[C2]) ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126] Real Time Clock Driver v1.12ac Non-volatile memory driver v1.2 Linux agpgart interface v0.102 (c) Dave Jones RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize input: Macintosh mouse button emulation as /class/input/input0 Xen virtual console successfully installed as xvc0 Event-channel device installed. usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice TCP bic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI No-Shortcut mode drivers/rtc/hctosys.c: unable to open rtc device (rtc0) Freeing unused kernel memory: 188k freed Write protecting the kernel read-only data: 795k ACPI: PCI Interrupt 0000:00:1a.7[D] -> GSI 19 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1a.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 18, io mem 0xffa7b400 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 19, io mem 0xffa7b000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.0: irq 20, io base 0x0000d880 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000d800 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1a.2 to 64 uhci_hcd 0000:00:1a.2: UHCI Host Controller uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1a.2: irq 17, io base 0x0000d480 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000d400 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000d080 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[D] -> GSI 16 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000d000 usb usb8: configuration #1 chosen from 1 choice hub 8-0:1.0: USB hub found hub 8-0:1.0: 2 ports detected SCSI subsystem initialized libata version 2.20 loaded. ahci 0000:00:1f.2: version 2.1 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18 usb 6-1: new low speed USB device using uhci_hcd and address 2 usb 6-1: configuration #1 chosen from 1 choice input: SOLIDTEK USB Composite Keyboard as /class/input/input1 input: USB HID v1.10 Keyboard [SOLIDTEK USB Composite Keyboard] on usb-0000:00:1d.0-1 input: SOLIDTEK USB Composite Keyboard as /class/input/input2 input,hiddev96: USB HID v1.10 Device [SOLIDTEK USB Composite Keyboard] on usb-0000:00:1d.0-1 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports ? Gbps 0x3f impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq stag led clo pmp pio slum part ata1: SATA max UDMA/133 cmd 0xee074900 ctl 0x00000000 bmdma 0x00000000 irq 18 ata2: SATA max UDMA/133 cmd 0xee074980 ctl 0x00000000 bmdma 0x00000000 irq 18 ata3: SATA max UDMA/133 cmd 0xee074a00 ctl 0x00000000 bmdma 0x00000000 irq 18 ata4: SATA max UDMA/133 cmd 0xee074a80 ctl 0x00000000 bmdma 0x00000000 irq 18 ata5: SATA max UDMA/133 cmd 0xee074b00 ctl 0x00000000 bmdma 0x00000000 irq 18 ata6: SATA max UDMA/133 cmd 0xee074b80 ctl 0x00000000 bmdma 0x00000000 irq 18 scsi0 : ahci ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ata_hpa_resize 1: sectors = 321672960, hpa_sectors = 321672960 ata1.00: ATA-7: Hitachi HDS721616PLA380, P22OAB3A, max UDMA/133 ata1.00: 321672960 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: ata_hpa_resize 1: sectors = 321672960, hpa_sectors = 321672960 ata1.00: configured for UDMA/133 scsi1 : ahci ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata2.00: ATAPI, max UDMA/66 ata2.00: configured for UDMA/66 scsi2 : ahci ata3: SATA link down (SStatus 0 SControl 300) scsi3 : ahci ata4: SATA link down (SStatus 0 SControl 300) scsi4 : ahci ata5: SATA link down (SStatus 0 SControl 300) scsi5 : ahci ata6: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA Hitachi HDS72161 P22O PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk scsi 1:0:0:0: CD-ROM PLEXTOR DVDR PX-755A 1.04 PQ: 0 ANSI: 5 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. ata1: D2H reg with I during NCQ, this message won't be printed again kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. security: 5 users, 11 roles, 2391 types, 114 bools, 1 sens, 1024 cats security: 67 classes, 215624 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev dm-0, type ext3), uses xattr SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts audit(1196713206.804:2): policy loaded auid=4294967295 sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 sd 0:0:0:0: Attached scsi generic sg0 type 0 sr 1:0:0:0: Attached scsi generic sg1 type 5 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled input: PC Speaker as /class/input/input3 8250_pnp: Unknown symbol serial8250_unregister_port 8250_pnp: Unknown symbol serial8250_register_port 8250_pnp: Unknown symbol serial8250_unregister_port 8250_pnp: Unknown symbol serial8250_register_port serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A FDC 0 is a National Semiconductor PC87306 Intel(R) PRO/1000 Network Driver - version 7.5.5.1-NAPI Copyright (c) 1999-2007 Intel Corporation. ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:19.0 to 64 e1000: 0000:00:19.0: e1000_probe: PHY reset is blocked due to SOL/IDER session. parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP] e1000: 0000:00:19.0: e1000_check_copper_options: Link active due to SoL/IDER Session. Speed/Duplex/AutoNeg parameter ignored. e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:13:20:f5:f8:50 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 17 ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:1b.0 to 64 serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A ACPI: PCI Interrupt 0000:00:03.3[B] -> GSI 17 (level, low) -> IRQ 16 device-mapper: multipath: version 1.0.5 loaded loop: loaded (max 8 devices) EXT3 FS on dm-0, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on dm-2, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev dm-2, type ext3), uses xattr SELinux: initialized (dev sda1, type ext2), uses xattr SELinux: initialized (dev sda2, type ext2), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs Adding 4194296k swap on /dev/mapper/xeni-swap. Priority:-1 extents:1 across:4194296k SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts IA-32 Microcode Update Driver: v1.14a-xen NET: Registered protocol family 10 lo: Disabled Privacy Extensions Mobile IPv6 ip6_tables: (C) 2000-2006 Netfilter Core Team ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (8192 buckets, 65536 max) ADDRCONF(NETDEV_UP): eth0: link is not ready e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000: eth0: e1000_watchdog_task: 10/100 speed: disabling TSO ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready audit(1196713221.215:3): audit_pid=1901 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0 SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts eth0: no IPv6 routers present SELinux: initialized (dev autofs, type autofs), uses genfs_contexts SELinux: initialized (dev autofs, type autofs), uses genfs_contexts SELinux: initialized (dev autofs, type autofs), uses genfs_contexts Bridge firewalling registered ADDRCONF(NETDEV_UP): peth0: link is not ready e1000: peth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000: peth0: e1000_watchdog_task: 10/100 speed: disabling TSO ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready device peth0 entered promiscuous mode eth0: port 1(peth0) entering learning state eth0: topology change detected, propagating eth0: port 1(peth0) entering forwarding state virbr0: no IPv6 routers present peth0: no IPv6 routers present eth0: no IPv6 routers present xen-vbd: registered block device major 202 blkfront: xvda: barriers enabled xvda:<0>Eeek! page_mapcount(page) went negative! (-1) page pfn = 29384 page->flags = 835 page->count = 3 page->mapping = eb093d98 vma->vm_ops = gntdev_vmops+0x0/0x34 vma->vm_ops->nopage = 0x0 vma->vm_file->f_op->mmap = gntdev_mmap+0x0/0x467 ------------[ cut here ]------------ kernel BUG at mm/rmap.c:574! invalid opcode: 0000 [#1] SMP last sysfs file: /devices/xen/vbd-51712/devtype Modules linked in: xenblk(U) ipt_MASQUERADE(U) iptable_nat(U) nf_nat(U) bridge(U) autofs4(U) sunrpc(U) nf_conntrack_netbios_ns(U) nf_conntrack_ipv4(U) xt_state(U) nf_conntrack(U) nfnetlink(U) ipt_REJECT(U) iptable_filter(U) ip_tables(U) xt_tcpudp(U) ip6t_REJECT(U) ip6table_filter(U) ip6_tables(U) x_tables(U) ipv6(U) ext2(U) loop(U) dm_multipath(U) 8250_pci(U) snd_hda_intel(U) snd_hda_codec(U) snd_seq_dummy(U) snd_seq_oss(U) snd_seq_midi_event(U) snd_seq(U) snd_seq_device(U) snd_pcm_oss(U) snd_mixer_oss(U) snd_pcm(U) snd_timer(U) parport_pc(U) snd(U) i2c_i801(U) ata_generic(U) e1000(U) parport(U) floppy(U) serio_raw(U) pcspkr(U) soundcore(U) i2c_core(U) 8250(U) snd_page_alloc(U) sg(U) sr_mod(U) serial_core(U) cdrom(U) ata_piix(U) dm_snapshot(U) dm_zero(U) dm_mirror(U) dm_mod(U) ahci(U) liba ta(U) sd_mod(U) scsi_mod(U) ext3(U) jbd(U) mbcache(U) uhci_hcd(U) ohci_hcd(U) ehci_hcd(U) CPU: 1 EIP: 0061:[] Not tainted VLI EFLAGS: 00210282 (2.6.21-2952.fc8xen #1) EIP is at page_remove_rmap+0xce/0xed eax: 00000036 ebx: c2371080 ecx: 00000001 edx: 00000000 esi: e92aed84 edi: 00000020 ebp: 53584067 esp: e9245ea4 ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0069 Process blkbackd (pid: 3154, ti=e9245000 task=c1d95150 task.ti=e9245000) Stack: c1291346 eb093d98 c1156c6b 00000000 c105d7fa 00000000 00000000 ffffffef b7f03000 e92aed84 e9245f68 53584067 00000000 003ff000 b7f03000 00000000 00000000 b7f04000 e95a1010 00000000 eb128580 e92df818 c2371080 c1c64900 Call Trace: [] gntdev_clear_pte+0x0/0x289 [] unmap_vmas+0x62e/0x8bd [] __wake_up+0x32/0x43 [] unmap_region+0x93/0xf7 [] do_munmap+0x15a/0x1ac [] sys_munmap+0x30/0x3e [] syscall_call+0x7/0xb ======================= Code: c0 74 0d 8b 50 08 b8 76 13 29 c1 e8 35 af fd ff 8b 46 4c 85 c0 74 14 8b 40 10 85 c0 74 0d 8b 50 2c b8 95 13 29 c1 e8 1a af fd ff <0f> 0b eb fe 8b 53 10 89 d8 59 5b 5b 83 e2 01 5e f7 da 83 c2 04 EIP: [] page_remove_rmap+0xce/0xed SS:ESP 0069:e9245ea4