* Re: boot Xen 4.0
@ 2010-06-04 20:30 ccmail111
2010-06-04 20:34 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 15+ messages in thread
From: ccmail111 @ 2010-06-04 20:30 UTC (permalink / raw)
To: Pasi Kärkkäinen; +Cc: deshantm, yingbin wang, xen-devel
[-- Attachment #1.1: Type: text/plain, Size: 16895 bytes --]
Hi Pasi,
Here is output of serial console where I see Xen4.0 stuck during boot up:
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x2768000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 00000000b4000000->00000000b8000000 (725348 pages to be all
ocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff81000000->ffffffff82768000
(XEN) Init. ramdisk: ffffffff82768000->ffffffff82c1ec00
(XEN) Phys-Mach map: ffffffff82c1f000->ffffffff831c7b20
(XEN) Start info: ffffffff831c8000->ffffffff831c84b4
(XEN) Page tables: ffffffff831c9000->ffffffff831e6000
(XEN) Boot stack: ffffffff831e6000->ffffffff831e7000
(XEN) TOTAL: ffffffff80000000->ffffffff83400000
(XEN) ENTRY ADDRESS: ffffffff81a63200
(XEN) Dom0 has maximum 4 VCPUs
(XEN) Scrubbing Free RAM: .done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen
)
(XEN) Freed 156kB init memory.
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.32.13 (gcc version 4.1.2 20080704 (Red Hat
4.1.2-44)) #2 SMP Thu May 20 17:22:39 PDT 2010
Command line: ro root=/dev/sda2 console=hvc0 earlyprintk=xen nomodeset debug log
level=10
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
released 0 pages of unused memory
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 0000000000095800 (usable)
Xen: 0000000000095800 - 0000000000100000 (reserved)
Xen: 0000000000100000 - 00000000b5164000 (usable)
Xen: 00000000bf7a5800 - 00000000c0000000 (reserved)
Xen: 00000000f0000000 - 00000000f8000000 (reserved)
Xen: 00000000fec00000 - 00000000fed40000 (reserved)
Xen: 00000000fed45000 - 0000000100000000 (reserved)
bootconsole [xenboot0] enabled
DMI 2.6 present.
last_pfn = 0xb5164 max_arch_pfn = 0x400000000
x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-00000000b5164000
0000000000 - 00b5164000 page 4k
kernel direct mapping tables up to b5164000 @ 100000-6ad000
RAMDISK: 02768000 - 02c1ec00
ACPI: RSDP 00000000000e9010 00024 (v02 HP
ACPI: XSDT 00000000bf7b88e8 0006C (v01 HPQOEM SLIC-WKS 20091208 00000000)
ACPI: FACP 00000000bf7b8a88 000F4 (v03 HPQOEM TYLSBURG 00000001 00000000)
ACPI: DSDT 00000000bf7b92d7 0A73D (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
ACPI: FACS 00000000bf7b8800 00040
ACPI: APIC 00000000bf7b8b7c 00114 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: ASF! 00000000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00000001 00000000)
ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)
ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: 00000000bf7b8f0f 001B8 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: SSDT 00000000bf7c4ee6 011FC (v01 INTEL PPM RCM 80000001 INTL 20061109)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-00000000b5164000
Bootmem setup node 0 0000000000000000-00000000b5164000
NODE_DATA [0000000000008000 - 000000000001ffff]
bootmap [0000000000020000 - 0000000000036a2f] pages 17
(8 early reservations) ==> bootmem [0000000000 - 00b5164000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [00031c9000 - 00031e6000] XEN PAGETABLES ==> [00031c9000 - 00031e6000]
#2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#3 [0001000000 - 0002747680] TEXT DATA BSS ==> [0001000000 - 0002747680]
#4 [0002768000 - 0002c1ec00] RAMDISK ==> [0002768000 - 0002c1ec00]
#5 [0002c1f000 - 00031c9000] XEN START INFO ==> [0002c1f000 - 00031c9000]
#6 [0002748000 - 0002748120] BRK ==> [0002748000 - 0002748120]
#7 [0000100000 - 000068d000] PGTABLE ==> [0000100000
Any thoughts ?
Thanks !
CM
--- On Tue, 5/18/10, ccmail111 <ccmail111@yahoo.com> wrote:
From: ccmail111 <ccmail111@yahoo.com>
Subject: Re: [Xen-devel] boot Xen 4.0
To: "Pasi Kärkkäinen" <pasik@iki.fi>
Cc: "yingbin wang" <yingbin.wangyb@gmail.com>, deshantm@gmail.com, xen-devel@lists.xensource.com
Date: Tuesday, May 18, 2010, 5:46 PM
Hi Pasi,
I'm sorry for typo below grub.conf is:
title Xen 4.0 debug XenLinux 2.6
root (hd0,0)
kernel /xen-4.0.0.gz console=com1, com1=115200,8n1 noreboot loglvl=all vga=text-80x50,keep iommu=off apic=debug guest_loglvl=all
module /vmlinuz-2.6.31.13 ro root=/dev/sda3 console=hvc0 earlyprintk=xen nomodeset initcall_debug debug loglevel=10
module /initrd.img-2.6.31.13
on another PC during boot up I see another problem - it is stuck at error:
ACPI Error (dsField-0140): [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS.
ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0._OSCI] (Node ffff8800b4c12500), AE_ALREADY_EXISTS
aer 0000:00:01.0: pcie02: AER service couldn't init device: _OSC failed
<...clip..errors...>
(XEN) irq.c: 1182:d0 Cannot bind IRQ 0 to guest. Will not share with others.
<..clip..>
[drm] Initialized drm 1.1.0 20060810
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
Any thoughts ?
Thanks !
CM
--- On Tue, 5/18/10, Pasi Kärkkäinen <pasik@iki.fi> wrote:
From: Pasi Kärkkäinen <pasik@iki.fi>
Subject: Re: [Xen-devel] boot Xen 4.0
To: "ccmail111" <ccmail111@yahoo.com>
Cc: "yingbin wang" <yingbin.wangyb@gmail.com>, deshantm@gmail.com,
xen-devel@lists.xensource.com
Date: Tuesday, May 18, 2010, 3:11 PM
On Tue, May 18, 2010 at 12:08:36PM -0700, ccmail111 wrote:
> Thanks for tip below.
>
> 1) I tried rebuild kernel with option below. I now build kernel with:
>
> CONFIG_SYSFS_DEPRECATED=y
> CONFIG_SYSFS_DEPRECATED_V2=y
>
> But see problem below during boot up as below..
>
> grub.conf:
>
> title Xen 4.0 debug XenLinux 2.6
> root (hd0,0)
> kernel /xen-4.0.0.gz console=com1, com1=115200,8n1 noreboot
> loglvl=all vga=text-80x50,keep iommu=off apic=debug guest_loglvl=all
> module /vmlinuz-2.6.31.13 ro
root=/dev/ram0 console=hvc0
> earlyprintk=xen nomodeset initcall_debug debug loglevel=10
your root= parameter is wrong.
You need to have the actual root partition path there.
-- Pasi
> module /initrd.img-2.6.31.13
>
> 2) Is there a reference (working) ramdisk/initrd for Xen4.0 with busybox
> or such ? I created ramdisk as:
>
> # mkinitrd -v -f --builtin=ehci-hcd --builtin=ohci-hcd --builtin=uhci-hcd
> --builtin=ahci --builtin=aacraid --builtin=aacraid --builtin=sd_mod
> --builtin=scsi_mod /boot/initrd.img-2.6.31.13 2.6.31.13
>
> Using this (since there is no busybox or such):
>
> Trying to resume from /dev/sdb2
> Unable to access resume device (/dev/sdb2)
>
Creating root device.
> usb 5-1: new full speed USB device using uhci_hcd and address 2
> Mounting root filesystem.
> VFS: Can't find ext3 filesystem on dev ram0.
> mount: error mounting /dev/root on /sysroot as ext3: Invalid argument
> Setting up other filesystems.
> Setting up new root fs
> setuproot: moving /dev failed: No such file or directory
> no fstab.sys, mounting internal defaults
> setuproot: error mounting /proc: No such file or directory
> setuproot: error mounting /sys: No such file or directory
> Switching to new root and running init.
> unmounting old /dev
> unmounting old /proc
> unmounting old /sys
> switchroot: mount failed: No such file or
directory
> Kernel panic - not syncing: Attempted to kill init!
> Pid: 1, comm: init Not tainted 2.6.31.13 #8
> Call Trace:
> [<ffffffff8106bbeb>] panic+0xb7/0x172
> [<ffffffff8106fe04>] ? do_exit+0x37c/0x6de
> [<ffffffff8100fa6f>] ? xen_restore_fl_direct_end+0x0/0x1
> [<ffffffff810a1c6b>] ? lock_release+0x197/0x1b8
> [<ffffffff8109ef6e>] ? trace_hardirqs_on+0x20/0x36
> [<ffffffff815436be>] ? _write_unlock_irq+0x46/0x61
> [<ffffffff8106fb15>] do_exit+0x8d/0x6de
> [<ffffffff8107021e>] sys_exit_group+0x0/0x42
> [<ffffffff8154265c>] ? trace_hardirqs_on_thunk+0x3a/0x3f
>
[<ffffffff81070248>] sys_exit_group+0x2a/0x42
> [<ffffffff81015332>] system_call_fastpath+0x16/0x1b
>
> Any suggestions ?
>
> Thanks !
>
> CM
>
> --- On Sat, 5/15/10, yingbin wang <yingbin.wangyb@gmail.com> wrote:
>
> From: yingbin wang <yingbin.wangyb@gmail.com>
> Subject: Re: [Xen-devel] boot Xen 4.0
> To: "ccmail111" <ccmail111@yahoo.com>
> Cc: "Pasi Kärkkäinen" <pasik@iki.fi>, deshantm@gmail.com,
> xen-devel@lists.xensource.com
> Date: Saturday, May 15, 2010, 12:34 PM
>
> I met similar problems and solved it.
>
> if your grub.conf is OK, you can try to edit a option of your .config.
> CONFIG_SYSFS_DEPRECATED_V2=y
>
> 2010/5/14 ccmail111 <ccmail111@yahoo.com>
> >
> > Thanks Pasi/Todd,
>
>
> > I did:
> > # mkinitrd -v -f --builtin=ehci-hcd --builtin=ohci-hcd
> --builtin=uhci-hcd --builtin=ahci --builtin=aacraid --builtin=aacraid
> --builtin=sd_mod --builtin=scsi_mod /boot/initrd.img-2.6.31.13 2.6.31.13
> >
> >
> > Now
> > I see during boot: kernel panic:
> >
> > Mounting root filesystem.
> > mount: could not find filesystem '/dev/root'
> > setting up other filesystems
> > setting up new root fs
> > setuproot: moving /dev failed No such file or directory
> > setuproot: error mounting /proc: No such file or
directory
> > setuproot: error mounting /sys: No such file or directory
> > switchroot: mount failed: No such file or directory
> > kernel panic - not syncing : Attempted to kill init !
> >
> >
> >
> >
> > --- On Thu, 5/13/10, Pasi Kärkkäinen <pasik@iki.fi> wrote:
> >
> > From: Pasi Kärkkäinen <pasik@iki.fi>
> > Subject: Re: [Xen-devel] initrd Xen 4.0
> > To: "ccmail111" <ccmail111@yahoo.com>
> > Cc: deshantm@gmail.com, xen-devel@lists.xensource.com
> > Date: Thursday, May 13, 2010, 4:27 PM
> >
> > On Thu, May 13, 2010 at 01:08:36PM -0700, ccmail111 wrote:
> > > The #5 of README is not clear in details.
> > > which directory to run depmod and mkinitrd from ?
> > >
> >
> > It doesn't matter.
> >
> > > I see:
>
> >
> > > # depmod xen-4.0.0
> > > WARNING: Couldn't find symtab and strtab in module xen-4.0.0
> > >
> >
> > Wrong. You need to run depmod for the *kernel*, not for xen.
> >
> > So like this:
> > depmod -a 2.6.32.12
> >
> > Or whatever is your kernel version.
> >
> > -- Pasi
> >
> > > # ls -l
> > > total 1356
> > > -rw-r--r-- 1 root root 1380620 May 13 13:05 xen-4.0.0
>
> >
> > > Any suggestions ?
> > >
> > > --- On Wed, 5/12/10, Todd Deshane <deshantm@gmail.com> wrote:
> > >
> > > From: Todd Deshane <deshantm@gmail.com>
> > > Subject: Re: [Xen-devel] initrd Xen 4.0
> > > To: "ccmail111" <ccmail111@yahoo.com>
> > > Cc: xen-devel@lists.xensource.com
> > > Date: Wednesday, May 12, 2010, 9:46 PM
> > >
> > > Hi,
> > >
> > > See inline.
> > >
> > > On Wed, May 12, 2010 at 12:25 PM, ccmail111
> <[1]ccmail111@yahoo.com>
> > > wrote:
> > > >
> > > > Hi,
> > > >
> >
> > I downloaded Xen 4.0 and did:
> > > > make install
> > > > I donot see initrd (ramdisk) being created at all.
> > > >
> > > > Any suggestions ?
> > > >
> > >
> > > Step 5 of the README
> > > Depending on your config, you may need to use 'mkinitrd' to
> create
> > > an initial ram disk, just like a native system e.g.
> > > # depmod
2.6.18-xen
> > > # mkinitrd -v -f --with=aacraid --with=sd_mod
> --with=scsi_mod
> > > initrd-2.6.18-xen.img 2.6.18-xen
> > > Other systems may requires the use of 'mkinitramfs' to
> create the
> > > ram disk.
> > > # depmod 2.6.18-xen
> > > # mkinitramfs -o initrd-2.6.18-xen.img 2.6.18-xen
> > >
> > > You may need to change the kernel version based on what you
> built.
> >
> Also some distros use different commands to build initrd files.
> > >
> > > I actually forgot about this step for a second too.
> > >
> > > Thanks,
> > > Todd
> > >
> > > --
> > > Todd Deshane
> > > [2][1]http://todddeshane.net
> > > [3][2]http://runningxen.com
> > >
> > > References
>
> >
> > > Visible links
> > > 1. file:///mc/compose?to=ccmail111@yahoo.com
> > > 2. [3]http://todddeshane.net/
> > > 3. [4]http://runningxen.com/
> >
> > > _______________________________________________
> > > Xen-devel mailing list
> > > Xen-devel@lists.xensource.com
> > > [5]http://lists.xensource.com/xen-devel
> >
> >
> >
> > _______________________________________________
> > Xen-devel mailing list
> > Xen-devel@lists.xensource.com
> > [6]http://lists.xensource.com/xen-devel
> >
>
> References
>
> Visible links
> 1. http://todddeshane.net/
> 2. http://runningxen.com/
> 3. http://todddeshane.net/
> 4. http://runningxen.com/
> 5. http://lists.xensource.com/xen-devel
> 6. http://lists.xensource.com/xen-devel
[-- Attachment #1.2: Type: text/html, Size: 37698 bytes --]
[-- Attachment #2: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 15+ messages in thread* Re: boot Xen 4.0
2010-06-04 20:30 boot Xen 4.0 ccmail111
@ 2010-06-04 20:34 ` Konrad Rzeszutek Wilk
0 siblings, 0 replies; 15+ messages in thread
From: Konrad Rzeszutek Wilk @ 2010-06-04 20:34 UTC (permalink / raw)
To: ccmail111; +Cc: deshantm, yingbin wang, xen-devel
On Fri, Jun 04, 2010 at 01:30:06PM -0700, ccmail111 wrote:
> Hi Pasi,
>
> Here is output of serial console where I see Xen4.0 stuck during boot up:
There has to be more.. What happend with the Xen banner?
>
> (XEN) *** LOADING DOMAIN 0 ***
> (XEN) Xen kernel: 64-bit, lsb, compat32
> (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x2768000
> (XEN) PHYSICAL MEMORY ARRANGEMENT:
> (XEN) Dom0 alloc.: 00000000b4000000->00000000b8000000 (725348 pages to be all
> ocated)
> (XEN) VIRTUAL MEMORY ARRANGEMENT:
> (XEN) Loaded kernel: ffffffff81000000->ffffffff82768000
> (XEN) Init. ramdisk: ffffffff82768000->ffffffff82c1ec00
> (XEN) Phys-Mach map: ffffffff82c1f000->ffffffff831c7b20
> (XEN) Start info: ffffffff831c8000->ffffffff831c84b4
> (XEN) Page tables: ffffffff831c9000->ffffffff831e6000
> (XEN) Boot stack: ffffffff831e6000->ffffffff831e7000
> (XEN) TOTAL: ffffffff80000000->ffffffff83400000
> (XEN) ENTRY ADDRESS: ffffffff81a63200
> (XEN) Dom0 has maximum 4 VCPUs
> (XEN) Scrubbing Free RAM: .done.
> (XEN) Xen trace buffers: disabled
> (XEN) Std. Loglevel: All
> (XEN) Guest Loglevel: All
> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen
> )
> (XEN) Freed 156kB init memory.
> mapping kernel into physical memory
> Xen: setup ISA identity maps
> about to get started...
> Initializing cgroup subsys cpuset
> Initializing cgroup subsys cpu
> Linux version 2.6.32.13 (gcc version 4.1.2 20080704 (Red Hat
> 4.1.2-44)) #2 SMP Thu May 20 17:22:39 PDT 2010
> Command line: ro root=/dev/sda2 console=hvc0 earlyprintk=xen nomodeset debug log
> level=10
> KERNEL supported cpus:
> Intel GenuineIntel
> AMD AuthenticAMD
> Centaur CentaurHauls
> released 0 pages of unused memory
> BIOS-provided physical RAM map:
> Xen: 0000000000000000 - 0000000000095800 (usable)
> Xen: 0000000000095800 - 0000000000100000 (reserved)
> Xen: 0000000000100000 - 00000000b5164000 (usable)
> Xen: 00000000bf7a5800 - 00000000c0000000 (reserved)
> Xen: 00000000f0000000 - 00000000f8000000 (reserved)
> Xen: 00000000fec00000 - 00000000fed40000 (reserved)
> Xen: 00000000fed45000 - 0000000100000000 (reserved)
> bootconsole [xenboot0] enabled
> DMI 2.6 present.
> last_pfn = 0xb5164 max_arch_pfn = 0x400000000
> x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
> initial memory mapped : 0 - 20000000
> init_memory_mapping: 0000000000000000-00000000b5164000
> 0000000000 - 00b5164000 page 4k
> kernel direct mapping tables up to b5164000 @ 100000-6ad000
> RAMDISK: 02768000 - 02c1ec00
> ACPI: RSDP 00000000000e9010 00024 (v02 HP
> ACPI: XSDT 00000000bf7b88e8 0006C (v01 HPQOEM SLIC-WKS 20091208 00000000)
> ACPI: FACP 00000000bf7b8a88 000F4 (v03 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: DSDT 00000000bf7b92d7 0A73D (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
> ACPI: FACS 00000000bf7b8800 00040
> ACPI: APIC 00000000bf7b8b7c 00114 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: ASF! 00000000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)
> ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: 00000000bf7b8f0f 001B8 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: SSDT 00000000bf7c4ee6 011FC (v01 INTEL PPM RCM 80000001 INTL 20061109)
> ACPI: Local APIC address 0xfee00000
> No NUMA configuration found
> Faking a node at 0000000000000000-00000000b5164000
> Bootmem setup node 0 0000000000000000-00000000b5164000
> NODE_DATA [0000000000008000 - 000000000001ffff]
> bootmap [0000000000020000 - 0000000000036a2f] pages 17
> (8 early reservations) ==> bootmem [0000000000 - 00b5164000]
> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
> #1 [00031c9000 - 00031e6000] XEN PAGETABLES ==> [00031c9000 - 00031e6000]
> #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
> #3 [0001000000 - 0002747680] TEXT DATA BSS ==> [0001000000 - 0002747680]
> #4 [0002768000 - 0002c1ec00] RAMDISK ==> [0002768000 - 0002c1ec00]
> #5 [0002c1f000 - 00031c9000] XEN START INFO ==> [0002c1f000 - 00031c9000]
> #6 [0002748000 - 0002748120] BRK ==> [0002748000 - 0002748120]
> #7 [0000100000 - 000068d000] PGTABLE ==> [0000100000
>
>
> Any thoughts ?
It looks as if your serial card is eating up characters. You could lower
the baud-rate down to say 9600?
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: boot Xen 4.0
@ 2010-06-21 20:54 ccmail111
2010-06-22 17:30 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 15+ messages in thread
From: ccmail111 @ 2010-06-21 20:54 UTC (permalink / raw)
To: Konrad Rzeszutek Wilk; +Cc: deshantm, yingbin wang, xen-devel
[-- Attachment #1.1: Type: text/plain, Size: 26252 bytes --]
resending...
--- On Thu, 6/17/10, ccmail111 <ccmail111@yahoo.com> wrote:
From: ccmail111 <ccmail111@yahoo.com>
Subject: Re: [Xen-devel] boot Xen 4.0
To: "Konrad Rzeszutek Wilk" <konrad.wilk@oracle.com>
Cc: deshantm@gmail.com, "yingbin wang" <yingbin.wangyb@gmail.com>, xen-devel@lists.xensource.com
Date: Thursday, June 17, 2010, 2:27 PM
Thanks Konrad for your help. I tried your suggestion but see below:
Please let me know next steps..
grub entry:
title Xen 4.0 debug XenLinux 2.6
root (hd0,1)
kernel /boot/xen-4.0.0.gz noreboot dom0_mem=max:1G loglvl=all com1=38400,8n1 console=com1 iommu=off guest_loglvl=all
module /boot/vmlinuz-2.6.32.13 ro root=/dev/sda2 console=hvc0 earlyprintk=xen nomodeset debug loglevel=10
module /boot/initrd-2.6.32.13.img
(XEN) ACPI: FACP BF7B8A88, 00F4 (r3 HPQOEM TYLSBURG 1 0)EN) ACPI: ACPI
SLEEP INFO: pm1x_cnt[f804,460], pm1x_evt[f800,0]
(XEN) ACPI: DSDT BF7B92D7, A73D (r1 COMPAQ DSDT_PRJ 1 MSFT 100000E) wakeup_vec[bf7b880c], vec_size[20]
(XEN) ACPI: FACS BF7B8800, 0040EN) ACPI: Local APIC address 0x
(XEN) ACPI: APIC
BF7B8B7C, 0114 (r1 HPQOEM TYLSBURG 1 0)[0x01] lapic_id[0x00] enabled)
(XEN) ACPI: ASF! BF7B8C90, 0063 (r32 HPQOEM TYLSBURG 1 0)
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
(XEN) ACPI: MCFG BF7B8CF3, 003C (r1 HPQOEM TYLSBURG 1 0)PIC
version 21
(XEN) ACPI: LAPIC (ac
(XEN) ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 1 0)
(XEN) Processor #4 7:10 APIC version 21
(XEN) ACPI: DMAR BF7B8F0F, 01B8 (r1 HPQOEM TYLSBURG 1
0)
(XEN) ACPI: LAPIC (acpi_id[0x0
(XEN) ACPI: SSDT BF7C4EE6, 11FC (r1 INTEL PPM RCM 80000001 INTL 20061109)
(XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
(XEN) No NUMA configuration found
(XEN) ACPI: LAPIC
(XEN) Faking a node at 0000000000000000-00000000bf7a5000
(XEN) ACPI: LAPI
(XEN) Domain heap initialised] disabled)
(XEN) found SMP MP-table at 000f9bf0
(XEN) ACPI: LAPIC (acpi_id[0x0b]
(XEN) DMI 2.6 present.)
(XEN) Using APIC driver default
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
(XEN) ACPI: LAPIC_NMI (acpi_
(XEN) Processor #2 7:10 APIC version
21
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)nt[0x1])
(XEN) Processor #4 7:10 APIC version 21[0x04] high edge lint[
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)MI (acpi_id[0x07] high edge lint[0x1])
(XEN) ACPI:
LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)MI (acpi_id[0x08] high edge lint[0x1])
(XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)(id[0x01] address[0xfec00000] gsi_base[0])
(XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)C[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x00] disabled)
(XEN) ACPI: IOAPIC (id[0x02] address[0xfec1000
(XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x00] disabled)
(XEN) IOAPIC[1]: apic_id 2, version
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x00]
disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x00] disabled)NT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x00] disabled)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
(XEN) ACPI: IRQ9 used by overri
(XEN) ACPI: LAPIC_NMI
(acpi_id[0x02] high edge lint[0x1])mode: Flat. Using 3 I/O APICs
(XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])base: 0xfed00000
(XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0 se
(XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge
lint[0x1])
(XEN) Using sch
(XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
(XEN) Detected 2266.814 M
(XEN) ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])Initing memory sharing.
(XEN
(XEN) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
(XEN) - APIC MMIO
access virtualisation
(XEN) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
(XEN) - Extended Page Tables (EPT)
(XEN) ACPI: IOAPIC (id[0x02] address[0xfec10000] gsi_base[24])
(XEN) - Virtual N
(XEN) IOAPIC[1]: apic_id 2, version 32, address 0xfec10000, GSI 24-47
(XEN) HVM: ASIDs
enabled.
(XEN) TSC is reliable, synchroniz
(XEN) ACPI: IRQ2 used by override.
(
(XEN) ACPI: IRQ9 used by override.ET
(XEN) Enabling APIC mode: Flat. Using 3 I/O APICs
(XEN) microcode
(XEN) ACPI: HPET id: 0x8086a301
base: 0xfed00000
(XEN) mic
(XEN) PCI: MCFG configuration 0: base f0000000 se
(XEN) *** LOADING DOMAIN 0 ***
(XEN) - APIC MMIO access virtualisationernel: 64-bit, lsb, compat32
(XEN) - APIC TPR shadow
(XEN) Dom0 kernel:
(XEN) - Extended Page Tables (EPT)>
0x2768000
(XEN) - Virtual-Processor Identifiers (VPID)N) PHYSICAL MEMORY ARRANGEMENT:
(XEN) - Virtual NMI(XEN) Dom0 alloc.:
(XEN) - MSR direct-access bitmap00 (725348 pages to be all
(XEN) HVM: ASIDs enabled.
(XEN) HVM: VMX enabl
ocated)
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK
method
(XEN) Phys
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1dfdd
(XEN) TSC is reliable, synchronization unnecessaryN) Start info: ffffffff831c8000->ffffffff831c8
(XEN) Platform timer is 14.318MHz HPET
üHòÆõ ÿþüiþ
ÿ(XEN) Allocated console ring of 32 KiB.
(XEN) Page tables:
ffffffff831c9000-
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
\ \/ /___ _ __ | || | / _
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed
(XEN) ACPI sleep modes: S3f81a63200
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) Dom0 has maximum 4 VCPUs
(XEN) *** LOADING DOMAIN 0 ***XEN) Freed 156kB init memory.
(XEN) Xen kernel: 64-bit, lsb, compat32 kernel into physical memoryfer time: 1 s
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x2768000etup ISA identity maps
(XEN) Disc info
(XEN) PHYSICAL MEMORY ARRANGEMENT:d...
(XEN)
(XEN) Dom0 alloc.: 00000000b4000000->00000000b8000000 (725348 pages to be all
(XEN) Found 1 EDD info
Initializing cgroup
s
ocated)
(XEN)
(XEN) Phys-Mach map: ffffffff82c1f000->ffffffff831c7b20fsdffsfsfsfsfsdfdd
Xen: 0000000000095800 - 0000000000100000 (reserved)
hello fsdffsf
(XEN) Start info: ffffffff831c8000->ffffffff831c84b4fdd
Xen: 0000000000100000 - 00000000
üHòÆõ ÿþüiþ¿¯óÅÿçü __ __ (r2 HPQOEM)
(XEN) Page tables: ffffffff831c9000->ffffffff831e6000
Xen: 00000000bf7a5800 -
00000000c0000000 (reserved)PQ
\ \/ /___ _ __ | || | / _ 0)
/_/\_\___|_| |_| |_|(_)7010600070106
(XEN) ENTRY ADDRESS: ffffffff81a63200
(XE
initial memory mapped
(XEN) Xen version 4.0.0 (sun 1 0)
(XEN) Dom0 has maximum 4 VCPUs
(XEN) Freed 156kB init
memory.00000000000-00000000b5164000
(X
mapping kernel into physical memoryfer time: 1 secondsCPI: MCFG BF7B8CF3, 003C
Xen: setup ISA identity mapsge 4k 0)
(XEN) Disc info
k
about to get started...les up to b5164000 @ 10
(XEN) Found 1: TCPA BF7B8D2
Initializing cgroup subsys cpuset 1
(XEN) Found 1 EDD
info
Initializing cgroup s
Xen: 0000000000000000 - 0000000000095800 (usable)0000000)
(XEN) 00000000fed45000 - 0000000100000000 (rG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG
Xen: 0000000000095800 - 0000000000100000
(reserved)
AC
(XEN) System RAM: 3033MB (3106320kB)HPQOEM TYLSBURG 00000001 000000
Xen: 0000000000100000 - 00000000b5164000 (usable)9010, 0024 (r2 HPQOEM)
ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001
Xen: 00000000bf7a5800 - 00000000c0000000 (reserved)PQOEM SLIC-WKS 20091208 0)
ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM
TYLS
x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106: Local APIC address 0xfee00000APIC address 0xfee00000
(XE
No
initial memory mapped : 0 - 20000000OEM TYLSBURG 1 0)0000000000000-00000000b5164000
(XEN)
init_memory_mapping: 0000000000000000-00000000b5164000b5164000
(XEN) ACPI: LAPIC
(acpi_id[0x02] la
(XEN) ACPI: MCFG BF7B8CF3, 003C008000 - 000000000001ffff]
0000000000 - 00b5164000 page 4k 0)
bootmap [0000000000020000 - 000000000
kernel direct mapping tables up to b5164000 @ 100000-6ad000ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 10000000 - 00b5164000]or #4 7:10 APIC version 21
ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)002747680] ACPI: LAPIC
(acpi_id[0x08] lapic_id[0x00] disabled)
ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG 00000001 00000000)2c1ec00]0] disabled)
ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)c9000]
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[
ACPI: HPET 00000000bf7b8ed7 00038
(v01 HPQOEM TYLSRK
No NUMA configuration found
(XEN) ACPI: LAPIC (acpi_i
Faking a node at 0000000000000000-00000000b51640000] lapic_id[0x00] disabled)
(XEN) Process
Bootmem setup node 0 0000000000000000-00000000b5164000I (acpi_id
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0
NODE_DATA [0000000000008000 - 000000000001ffff]I: LAPIC_NMI (acpi_
(XEN) Processor #2 7:10 APIC
bootmap [0000000000020000 - 0000000000036a2f] pages 17PI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)nt[0x1])
(8 early reservations) ==> bootmem [0000000000 - 00b5164000]or #4 7:10 APIC version 21[0x04] high edge
lint[
#3 [0001000000 - 0002747680] TEXT DATA BSS ==> [0001000000 - 0002747680] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)C[0]: apic_id 1, version
#4 [0002768000 - 0002c1ec00] RAMDISK ==> [0002768000 - 0002c1ec00]0] disabled)
(XEN) ACPI: IOAPIC (id[0x02] address[0xfec1000
(XEN) A
#5 [0002c1f000 - 00031c9000] XEN START INFO ==> [0002c1f000 - 00031c9000]OAPIC[1]: apic_id 2, version
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x00]
#6 [0002748000 - 0002748120] BRK
(XEN) ACPI:
/_/\_\___|_| |_| |_|(_)___(_)___/
(XEN) ACPI: LAPIC_NMI (acpi_id[0
(XEN) Xen version 4.0.0 (@) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-44
(XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])mode: Flat. Using 3
)) Tue Jun 8 15:44:03 PDT 2010
(XEN) ACPI: LAPIC_NMI (acpi
(XEN) Latest ChangeSet: unavailable0xfed00000
(XEN) Command line: noreboot dom0_mem=max:1G loglvl=all com1ge lint[0
se
(XEN) Found 1 MBR signatureshigh edge lint[0x1])Initing m
(XEN) Found 1 EDD information structures
(XEN
(XEN) ACPI: IOAPIC (id[0x01] addre
(XEN) Xen-e820 RAM map:0])
(XEN)
(XEN) 0000000000000000 - 0000000000095800 (usable)IC[0]: apic_id 1, version 32, address 0xfec00000, G
(XEN) 0000000000095800 - 00000000000a0000 (reserved))
(XEN) ACPI: IOAPIC (id[0x02] ad
(XEN) 00000000000e8000 - 0000000000100000
(reserved)
(XEN) - Virtual N
(XEN) IOAPIC[
(XEN) 0000000000100000 - 00000000bf7a5800 (usable)4-47
(XEN) HVM: ASIDs enabled.
(XEN) 00000000bf7a5800 - 00000
(XEN) ACPI: APIC BF7B8B7C, 0114 (r1 HPQOEM TYLSBURG 1 0)microcode: CPU3 resumed
(XEN) Using ACPI (MADT) for SMP configuration infor
(XEN) ACPI: ASF! BF7B8C90, 0063 (r32 HPQOEM TYLSBURG
1 0)cheduler: SMP Credit Scheduler (credit)ast
(XEN) ACPI: MCFG BF7B8CF3, 003C (r1 HPQOEM TYLSBURG 1 0)
(XEN)
(XEN) Initing memory sharing.ling timer started.
(XEN) ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 1 0)
(XEN) - APIC MMIO access virtualisationernel: 64-bit, lsb, compat32
(XEN) ACPI: SLIC BF7B8D61,
0176 (r1 HPQOEM SLIC-WKS 1 0) Page Tables (EPT)> 0x2768000
(XEN) - Virtual-Proc
(XEN) ACPI: HPET BF7B8ED7, 0038 (r1 HPQOEM TYLSBURG 1 0) - Virtual NMI(XEN) Dom0 alloc.:
(XEN) - MSR direct-access bitmap00 (725
(XEN) ACPI: DMAR BF7B8F0F, 01B8 (r1 HPQOEM TYLSBURG
(XEN) HVM: VMX enabl
ocated)
(XEN) ..TIMER: vector=0x
(XEN) DMI 2.6 present.=-1
pin2=-1
(XEN) Using APIC driver default ffffffff831c9
(XEN) TSC is re
(XEN) ACPI: PM-Timer IO Port: 0xf808
(XEN) Boot
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[f804,460], pm1x_evt[f800,0]
ÿ(XEN) Allocated console ring of 32 KiB.f
(XEN) ACPI: wakeup_vec[bf7b880c], vec_size[20]767 microcode: CPU1 resumedENTRY ADDRESS: ffffffff81a63200
(XEN) ACPI: Local APIC address 0xfee000007 microcode: CPU2
resumed
(XEN) Xen ke
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)Initializin
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr
(XEN) Processor #6 7:10 APIC version 21u
Linux v
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)080704 (Red Hat
(XEN) Dom0 alloc.: 00000000b40000
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)Thu May 20 17:22:39 PDT 2010
(XEN) Phys-Mach map: ffffffff82c1f000->ffffffff831
(XEN)
ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x00] disabled)
(XEN) Start info: ffffffff831c8000->ffffffff831c8
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x00] disabled)
(XEN) Page tables: ffffffff831c9000->ffffffff831e600
(XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x00] disabled)(XEN) Boot stack: ffffffff831e6000->ffffffff831e70000
(XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x00] disabled)EN) TOTAL: ffffffff80000000->ffffffff83400000580
(XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x00] disabled)) ENTRY ADDRESS: ffffffff81a63200000000f0000000 - 000000
(XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x00] disa
ma
(XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
initial
Xen: setup ISA identity maps
(XEN) ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])Initializing cgroup subsys cpuset
(XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
Linux version 2.6.32.13 (root@host)
(XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge
lint[0x1])
RAMDISK: 02768000 - 02c1ec00
(XEN) ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0024 (v02 HP
Xen: 00000000fed45000 - 0000000
(XEN) ACPI: IRQ9 used by override.0000bf7b8d61 00176 (v01 HPQOEM SLI
(XEN) Enabling APIC mode: Flat. Using 3 I/O APICs
DMI 2.6 present.
last_
(XEN) ACPI: HPET id: 0x8086a301 base: 0xfed00000M TYLSBURG 00000001
00000000)
x86 PAT ena
(XEN) PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 127 00000000bf7b8f0f 001B8 (v01 HPQOEM TY
initial memory mapped : 0 -
(XEN) PCI: MCFG area at f0000000 reserved in E820_memory_mapping: 0000000000000000-00000000b516400
(XEN) Using ACPI (MADT) for SMP configuration information000000000 - 00b5164000 page 4k
(XEN) Using scheduler: SMP Credit Scheduler (credit)00000-6ad000
No NUMA co
(XEN) Detected 2266.801 MHz processor. 02c1ec00ing a node at 00000000000000
(XEN) Initing memory sharing.024 (v02
HP
(XEN) - MSR direct-access bitmap #0 [0000000000 - 0000001
ACPI: F
(XEN) HVM: ASIDs enabled.000 - 0000001000]
(XEN) HVM: VMX enabled00000bf7b8b7c 00114 (v
(XEN) HVM: Hardware Assisted Paging detected.031e6000] XEN PAGETABLES ==> [00031c9000 -
(XEN) Intel machine check reporting enabled00000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00
(XEN) I/O virtualisation disabled TRAMPOLINE ==> [0000006000 -
(XEN) Total of 4 processors activated.MCFG 00000000bf7b8cf3 0003C (v01 HPQOE
(XEN) ENABLING IO-APIC IRQs00000)02747680] TEXT DAT
(XEN) -> Using new ACK method
ÿ(XEN) Allocated console ring of 32 KiB.7b8ed7 00038 (v01 HPQOEM TYLSBURG 000000
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
#7
ACPI:
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed0001 00000000)
(XEN) Brought up 4 CPUs _ _ ___ _
(XEN) microcode.c:73:d32767 microcode: CPU3 resumedM 80000001 INTL
20061109)
(XEN) Turbo Mode detected! | || |_| | | | | | |
(XEN) HPET: 4 timers in total, 0 timers will be used for broadcast |_|
No NUMA configuration found
/_/\_\___|_|
Faking
(XEN) ACPI sleep modes: S3-00000000b5164000
(8 early reservations) ==> bootmem [0000000000 - 00b5164000]
(XEN) PHYSICAL MEMORY ARRANGEMENT:
#0 [000000
(XEN) Dom0 alloc.: 00000000b4000000->00000000b8000000 (245760 pages to be allN) VGA is text mode 80x25, font
8x16
#1 [00031c9000 -
ocated)000]
(XEN) VIRTUAL MEMORY ARRANGEMENT:0031e6000]
(XEN) Loaded kernel: ffffffff81000000->ffffffff82768000#2 [0000006000 - 0000008000] TRAMPOLINE ==> [00000
(XEN) Init. ramdisk: ffffffff82768000->ffffffff82c1ec00ructures
#3 [0001000000
(XEN) Phys-Mach map: ffffffff82c1f000->ffffffff800000000000000 -
000
(XEN) 00000000f0000000 - 0
(XEN) ENTRY ADDRESS: ffffffff81a63200d000] PGTABLE ==> [0000100000
(XEN) Dom0 has maximum 4 VCPUs000000fed40000 (reserved)
(XEN) Scrubbing Free RAM: ....................done.N) 00000000fed45000 - 00
\ \/ /___ _ __ | || |
(XEN) Xen trace buffers: disabled
\ // _ \ '_ \
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All | |__ _| |_| | |_| |OE
(XEN) *** Serial input ->
DOM0 (type 'CTRL-a' three times to switch input to Xen HPQOEM SLIC-WKS 20091208
)
(XEN) C
Initializing cgroup subsys cpul com1=38400,8n1 console=com1
Linux version 2.6.32.13 (root@host) (gcc version 4.1.2 20080704 (Red Hat
est_loglvl=all
(XEN) Video information:
(XEN) AC
4.1.2-44)) #2 SMP Thu May 20 17:22:39 PDT 201016 1
0)
(XEN
Command line: ro root=/dev/sda2 console=hvc0 earlyprintk=xen nomodeset debug log (r1 HPQOEM TYLSBURG 1
(XEN) Disc information:
(XE
level=10 1 MBR s
KERNEL supported cpus:(XEN) ACPI: TCP
(XEN)
Intel GenuineIntelion structures 1
AMD AuthenticAMD
bootconsole [xenboot0] enabled
DMI 2.6 present.
last_pfn = 0x40000 max_arch_pfn = 0x400000000
x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
initial memory mapped : 0 - 20000000
init_memory_mapping:
0000000000000000-0000000040000000
0000000000 - 0040000000 page 4k
kernel direct mapping tables up to 40000000 @ 100000-302000
RAMDISK: 02768000 - 02c1ec00
ACPI: RSDP 00000000000e9010 00024 (v02 HPQOEM)
ACPI: XSDT 00000000bf7b88e8 0006C (v01 HPQOEM SLIC-WKS 20091208 00000000)
ACPI: FACP 00000000bf7b8a88 000F4 (v03 HPQOEM TYLSBURG 00000001 00000000)
ACPI: DSDT 00000000bf7b92d7 0A73D (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
ACPI: FACS 00000000bf7b8800 00040
ACPI: APIC 00000000bf7b8b7c 00114 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: ASF! 00000000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00000001 00000000)
ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG
00000001 00000000)
ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)
ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: 00000000bf7b8f0f 001B8 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: SSDT 00000000bf7c4ee6 011FC (v01 INTEL PPM RCM 80000001 INTL 20061109)
ACPI: Local APIC address 0xfee00000
No NUMA co
<stuck>
--- On Tue, 6/15/10, Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> wrote:
From: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Subject: Re: [Xen-devel] boot Xen 4.0
To: "ccmail111" <ccmail111@yahoo.com>
Cc: deshantm@gmail.com, "yingbin wang"
<yingbin.wangyb@gmail.com>, xen-devel@lists.xensource.com
Date: Tuesday, June 15, 2010, 5:26 PM
> Linux version 2.6.32.13 (root@xyz) (gcc version 4.1.2 20080704 (Red Hat0095800 (usable)
> (XEN) 00000
> 4.1.2-44)) #2 SMP Thu May 20 17:22:39 PDT 2010
>
> Xen: 0000000000000000 - 0000000000095800
(usable)
> (XEN) 00000000fed45000 - 0000000100000000 (r
> Xen: 0000000000095800 - 0000000000100000 (reserved)
> (XEN) System RAM: 3033MB (3106320kB)
> Xen: 0000000000100000 - 00000000b5164000 (usable)9010, 0024 (r2 HPQOEM)
> Xen: 00000000bf7a5800 - 00000000c0000000 (reserved)PQOEM SLIC-WKS 20091208 0)
> Xen: 00000000f0000000 - 00000000f8000000 (reserved)
>
> last_pfn = 0xb5164 max_arch_pfn = 0x400000000
> (XEN) ACPI: APIC BF7B8B7C, 01
> x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
> (XE
> initial memory mapped : 0 - 20000000OEM TYLSBURG
1 0)
> init_memory_mapping: 0000000000000000-00000000b5164000
> (XEN) ACPI: MCFG BF7B8CF3, 003C
> 0000000000 - 00b5164000 page 4k 0)
> kernel direct mapping tables up to b5164000 @ 100000-6ad000ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 1
> RAMDISK: 02768000 - 02c1ec00
> ACPI: FACS 00000000bf7b8800 00040
> ACPI: APIC
00000000bf7b8b7c 00114 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: ASF! 00000000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)
> ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: 00000000bf7b8f0f 001B8 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: SSDT 00000000bf7c4ee6 011FC (v01 INTEL PPM RCM 80000001 INTL 20061109)
> ACPI: Local APIC address 0xfee00000
> No NUMA configuration
found
> Faking a node at 0000000000000000-00000000b5164000
> Bootmem setup node 0 0000000000000000-00000000b5164000
> NODE_DATA [0000000000008000 - 000000000001ffff]
> bootmap [0000000000020000 - 0000000000036a2f] pages 17
> (8 early reservations) ==> bootmem [0000000000 - 00b5164000]
> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
> #1 [00031c9000 - 00031e6000] XEN PAGETABLES ==> [00031c9000 - 00031e6000]
> #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
> #3 [0001000000 - 0002747680] TEXT DATA BSS ==> [0001000000 - 0002747680]
> #4 [0002768000 - 0002c1ec00] RAMDISK ==> [0002768000 - 0002c1ec00]
> #5 [0002c1f000 -
00031c9000] XEN START INFO ==> [0002c1f000 - 00031c9000]
> #6 [0002748000 - 0002748120] BRK ==> [0002748000 - 0002748120]
> #7 [0000100000 - 000068d000] PGTABLE ==> [0000100000
>
>
This points to the E820 being wacked, but I can't see how that is
possible considering Xen boots. Try forcing your domain to a smaller
memory amount. Use 'dom0_mem=max:1G' in your Xen command line.
[-- Attachment #1.2: Type: text/html, Size: 51248 bytes --]
[-- Attachment #2: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 15+ messages in thread* Re: boot Xen 4.0
2010-06-21 20:54 ccmail111
@ 2010-06-22 17:30 ` Konrad Rzeszutek Wilk
0 siblings, 0 replies; 15+ messages in thread
From: Konrad Rzeszutek Wilk @ 2010-06-22 17:30 UTC (permalink / raw)
To: ccmail111; +Cc: deshantm, yingbin wang, xen-devel
On Mon, Jun 21, 2010 at 01:54:43PM -0700, ccmail111 wrote:
>
> resending...
>
> --- On Thu, 6/17/10, ccmail111 <ccmail111@yahoo.com> wrote:
>
> From: ccmail111 <ccmail111@yahoo.com>
> Subject: Re: [Xen-devel] boot Xen 4.0
> To: "Konrad Rzeszutek Wilk" <konrad.wilk@oracle.com>
> Cc: deshantm@gmail.com, "yingbin wang" <yingbin.wangyb@gmail.com>, xen-devel@lists.xensource.com
> Date: Thursday, June 17, 2010, 2:27 PM
>
> Thanks Konrad for your help. I tried your suggestion but see below:
> Please let me know next steps..
This is realy puzzling. There is nothing in the Linux source code that would explain
why it would hang after printing the early reservations. It does not help that your serial
output is mangled up. Lets see if we can get the serial console to print
the date properly. Try adding this in:
sync_console console_to_ring console=com1,vga
>
> grub entry:
>
>
> title Xen 4.0 debug XenLinux 2.6
> root (hd0,1)
> kernel /boot/xen-4.0.0.gz noreboot dom0_mem=max:1G loglvl=all com1=38400,8n1 console=com1 iommu=off guest_loglvl=all
> module /boot/vmlinuz-2.6.32.13 ro root=/dev/sda2 console=hvc0 earlyprintk=xen nomodeset debug loglevel=10
> module /boot/initrd-2.6.32.13.img
>
>
>
> (XEN) ACPI: FACP BF7B8A88, 00F4 (r3 HPQOEM TYLSBURG 1 0)EN) ACPI: ACPI
> SLEEP INFO: pm1x_cnt[f804,460], pm1x_evt[f800,0]
> (XEN) ACPI: DSDT BF7B92D7, A73D (r1 COMPAQ DSDT_PRJ 1 MSFT 100000E) wakeup_vec[bf7b880c], vec_size[20]
> (XEN) ACPI: FACS BF7B8800, 0040EN) ACPI: Local APIC address 0x
> (XEN) ACPI: APIC
> BF7B8B7C, 0114 (r1 HPQOEM TYLSBURG 1 0)[0x01] lapic_id[0x00] enabled)
> (XEN) ACPI: ASF! BF7B8C90, 0063 (r32 HPQOEM TYLSBURG 1 0)
> (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
> (XEN) ACPI: MCFG BF7B8CF3, 003C (r1 HPQOEM TYLSBURG 1 0)PIC
> version 21
> (XEN) ACPI: LAPIC (ac
> (XEN) ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 1 0)
> (XEN) Processor #4 7:10 APIC version 21
> (XEN) ACPI: DMAR BF7B8F0F, 01B8 (r1 HPQOEM TYLSBURG 1
> 0)
> (XEN) ACPI: LAPIC (acpi_id[0x0
> (XEN) ACPI: SSDT BF7C4EE6, 11FC (r1 INTEL PPM RCM 80000001 INTL 20061109)
> (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
> (XEN) No NUMA configuration found
> (XEN) ACPI: LAPIC
> (XEN) Faking a node at 0000000000000000-00000000bf7a5000
>
> (XEN) ACPI: LAPI
> (XEN) Domain heap initialised] disabled)
> (XEN) found SMP MP-table at 000f9bf0
> (XEN) ACPI: LAPIC (acpi_id[0x0b]
> (XEN) DMI 2.6 present.)
> (XEN) Using APIC driver default
>
> (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
> (XEN) ACPI: LAPIC_NMI (acpi_
> (XEN) Processor #2 7:10 APIC version
> 21
> (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)nt[0x1])
> (XEN) Processor #4 7:10 APIC version 21[0x04] high edge lint[
> (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)MI (acpi_id[0x07] high edge lint[0x1])
> (XEN) ACPI:
> LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)MI (acpi_id[0x08] high edge lint[0x1])
> (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)(id[0x01] address[0xfec00000] gsi_base[0])
> (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)C[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
> (XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x00] disabled)
> (XEN) ACPI: IOAPIC (id[0x02] address[0xfec1000
> (XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x00] disabled)
> (XEN) IOAPIC[1]: apic_id 2, version
> (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x00]
> disabled)
>
> (XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x00] disabled)NT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> (XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x00] disabled)
> (XEN) ACPI: IRQ0 used by override.
> (XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
> (XEN) ACPI: IRQ9 used by overri
> (XEN) ACPI: LAPIC_NMI
> (acpi_id[0x02] high edge lint[0x1])mode: Flat. Using 3 I/O APICs
> (XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])base: 0xfed00000
> (XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0 se
> (XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge
> lint[0x1])
> (XEN) Using sch
> (XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
> (XEN) Detected 2266.814 M
> (XEN) ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])Initing memory sharing.
> (XEN
> (XEN) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
> (XEN) - APIC MMIO
> access virtualisation
> (XEN) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
> (XEN) - Extended Page Tables (EPT)
> (XEN) ACPI: IOAPIC (id[0x02] address[0xfec10000] gsi_base[24])
> (XEN) - Virtual N
> (XEN) IOAPIC[1]: apic_id 2, version 32, address 0xfec10000, GSI 24-47
> (XEN) HVM: ASIDs
> enabled.
> (XEN) TSC is reliable, synchroniz
> (XEN) ACPI: IRQ2 used by override.
> (
> (XEN) ACPI: IRQ9 used by override.ET
> (XEN) Enabling APIC mode: Flat. Using 3 I/O APICs
> (XEN) microcode
> (XEN) ACPI: HPET id: 0x8086a301
> base: 0xfed00000
> (XEN) mic
> (XEN) PCI: MCFG configuration 0: base f0000000 se
>
> (XEN) *** LOADING DOMAIN 0 ***
> (XEN) - APIC MMIO access virtualisationernel: 64-bit, lsb, compat32
> (XEN) - APIC TPR shadow
> (XEN) Dom0 kernel:
> (XEN) - Extended Page Tables (EPT)>
> 0x2768000
> (XEN) - Virtual-Processor Identifiers (VPID)N) PHYSICAL MEMORY ARRANGEMENT:
> (XEN) - Virtual NMI(XEN) Dom0 alloc.:
> (XEN) - MSR direct-access bitmap00 (725348 pages to be all
> (XEN) HVM: ASIDs enabled.
> (XEN) HVM: VMX enabl
> ocated)
>
> (XEN) ENABLING IO-APIC IRQs
> (XEN) -> Using new ACK
> method
> (XEN) Phys
> (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1dfdd
> (XEN) TSC is reliable, synchronization unnecessaryN) Start info: ffffffff831c8000->ffffffff831c8
> (XEN) Platform timer is 14.318MHz HPET
> üHòÆõ ÿþüiþ
> ÿ(XEN) Allocated console ring of 32 KiB.
> (XEN) Page tables:
> ffffffff831c9000-
> (XEN) microcode.c:73:d32767 microcode: CPU1 resumed
> \ \/ /___ _ __ | || | / _
> (XEN) microcode.c:73:d32767 microcode: CPU2 resumed
> (XEN) ACPI sleep modes: S3f81a63200
> (XEN) mcheck_poll: Machine check polling timer started.
> (XEN) Dom0 has maximum 4 VCPUs
>
> (XEN) *** LOADING DOMAIN 0 ***XEN) Freed 156kB init memory.
> (XEN) Xen kernel: 64-bit, lsb, compat32 kernel into physical memoryfer time: 1 s
> (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x2768000etup ISA identity maps
> (XEN) Disc info
> (XEN) PHYSICAL MEMORY ARRANGEMENT:d...
> (XEN)
> (XEN) Dom0 alloc.: 00000000b4000000->00000000b8000000 (725348 pages to be all
> (XEN) Found 1 EDD info
> Initializing cgroup
> s
> ocated)
> (XEN)
> (XEN) Phys-Mach map: ffffffff82c1f000->ffffffff831c7b20fsdffsfsfsfsfsdfdd
> Xen: 0000000000095800 - 0000000000100000 (reserved)
> hello fsdffsf
> (XEN) Start info: ffffffff831c8000->ffffffff831c84b4fdd
> Xen: 0000000000100000 - 00000000
> üHòÆõ ÿþüiþ¿¯óÅÿçü __ __ (r2 HPQOEM)
> (XEN) Page tables: ffffffff831c9000->ffffffff831e6000
> Xen: 00000000bf7a5800 -
> 00000000c0000000 (reserved)PQ
> \ \/ /___ _ __ | || | / _ 0)
> /_/\_\___|_| |_| |_|(_)7010600070106
> (XEN) ENTRY ADDRESS: ffffffff81a63200
> (XE
> initial memory mapped
>
> (XEN) Xen version 4.0.0 (sun 1 0)
> (XEN) Dom0 has maximum 4 VCPUs
> (XEN) Freed 156kB init
> memory.00000000000-00000000b5164000
> (X
> mapping kernel into physical memoryfer time: 1 secondsCPI: MCFG BF7B8CF3, 003C
> Xen: setup ISA identity mapsge 4k 0)
> (XEN) Disc info
> k
> about to get started...les up to b5164000 @ 10
> (XEN) Found 1: TCPA BF7B8D2
> Initializing cgroup subsys cpuset 1
> (XEN) Found 1 EDD
> info
> Initializing cgroup s
>
> Xen: 0000000000000000 - 0000000000095800 (usable)0000000)
> (XEN) 00000000fed45000 - 0000000100000000 (rG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG
> Xen: 0000000000095800 - 0000000000100000
> (reserved)
> AC
> (XEN) System RAM: 3033MB (3106320kB)HPQOEM TYLSBURG 00000001 000000
> Xen: 0000000000100000 - 00000000b5164000 (usable)9010, 0024 (r2 HPQOEM)
> ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001
> Xen: 00000000bf7a5800 - 00000000c0000000 (reserved)PQOEM SLIC-WKS 20091208 0)
> ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM
> TYLS
> x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106: Local APIC address 0xfee00000APIC address 0xfee00000
> (XE
> No
> initial memory mapped : 0 - 20000000OEM TYLSBURG 1 0)0000000000000-00000000b5164000
> (XEN)
> init_memory_mapping: 0000000000000000-00000000b5164000b5164000
> (XEN) ACPI: LAPIC
> (acpi_id[0x02] la
> (XEN) ACPI: MCFG BF7B8CF3, 003C008000 - 000000000001ffff]
> 0000000000 - 00b5164000 page 4k 0)
> bootmap [0000000000020000 - 000000000
> kernel direct mapping tables up to b5164000 @ 100000-6ad000ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 10000000 - 00b5164000]or #4 7:10 APIC version 21
>
> ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)002747680] ACPI: LAPIC
> (acpi_id[0x08] lapic_id[0x00] disabled)
> ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG 00000001 00000000)2c1ec00]0] disabled)
>
> ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)c9000]
> (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[
> ACPI: HPET 00000000bf7b8ed7 00038
> (v01 HPQOEM TYLSRK
>
> No NUMA configuration found
> (XEN) ACPI: LAPIC (acpi_i
> Faking a node at 0000000000000000-00000000b51640000] lapic_id[0x00] disabled)
> (XEN) Process
> Bootmem setup node 0 0000000000000000-00000000b5164000I (acpi_id
> (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0
> NODE_DATA [0000000000008000 - 000000000001ffff]I: LAPIC_NMI (acpi_
> (XEN) Processor #2 7:10 APIC
> bootmap [0000000000020000 - 0000000000036a2f] pages 17PI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)nt[0x1])
> (8 early reservations) ==> bootmem [0000000000 - 00b5164000]or #4 7:10 APIC version 21[0x04] high edge
> lint[
> #3 [0001000000 - 0002747680] TEXT DATA BSS ==> [0001000000 - 0002747680] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)C[0]: apic_id 1, version
> #4 [0002768000 - 0002c1ec00] RAMDISK ==> [0002768000 - 0002c1ec00]0] disabled)
> (XEN) ACPI: IOAPIC (id[0x02] address[0xfec1000
> (XEN) A
> #5 [0002c1f000 - 00031c9000] XEN START INFO ==> [0002c1f000 - 00031c9000]OAPIC[1]: apic_id 2, version
> (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x00]
> #6 [0002748000 - 0002748120] BRK
>
>
>
> (XEN) ACPI:
> /_/\_\___|_| |_| |_|(_)___(_)___/
> (XEN) ACPI: LAPIC_NMI (acpi_id[0
>
> (XEN) Xen version 4.0.0 (@) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-44
> (XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])mode: Flat. Using 3
> )) Tue Jun 8 15:44:03 PDT 2010
> (XEN) ACPI: LAPIC_NMI (acpi
> (XEN) Latest ChangeSet: unavailable0xfed00000
> (XEN) Command line: noreboot dom0_mem=max:1G loglvl=all com1ge lint[0
> se
> (XEN) Found 1 MBR signatureshigh edge lint[0x1])Initing m
> (XEN) Found 1 EDD information structures
> (XEN
> (XEN) ACPI: IOAPIC (id[0x01] addre
> (XEN) Xen-e820 RAM map:0])
> (XEN)
> (XEN) 0000000000000000 - 0000000000095800 (usable)IC[0]: apic_id 1, version 32, address 0xfec00000, G
> (XEN) 0000000000095800 - 00000000000a0000 (reserved))
> (XEN) ACPI: IOAPIC (id[0x02] ad
> (XEN) 00000000000e8000 - 0000000000100000
> (reserved)
> (XEN) - Virtual N
> (XEN) IOAPIC[
> (XEN) 0000000000100000 - 00000000bf7a5800 (usable)4-47
> (XEN) HVM: ASIDs enabled.
> (XEN) 00000000bf7a5800 - 00000
> (XEN) ACPI: APIC BF7B8B7C, 0114 (r1 HPQOEM TYLSBURG 1 0)microcode: CPU3 resumed
> (XEN) Using ACPI (MADT) for SMP configuration infor
> (XEN) ACPI: ASF! BF7B8C90, 0063 (r32 HPQOEM TYLSBURG
> 1 0)cheduler: SMP Credit Scheduler (credit)ast
> (XEN) ACPI: MCFG BF7B8CF3, 003C (r1 HPQOEM TYLSBURG 1 0)
> (XEN)
> (XEN) Initing memory sharing.ling timer started.
> (XEN) ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 1 0)
> (XEN) - APIC MMIO access virtualisationernel: 64-bit, lsb, compat32
> (XEN) ACPI: SLIC BF7B8D61,
> 0176 (r1 HPQOEM SLIC-WKS 1 0) Page Tables (EPT)> 0x2768000
> (XEN) - Virtual-Proc
> (XEN) ACPI: HPET BF7B8ED7, 0038 (r1 HPQOEM TYLSBURG 1 0) - Virtual NMI(XEN) Dom0 alloc.:
> (XEN) - MSR direct-access bitmap00 (725
> (XEN) ACPI: DMAR BF7B8F0F, 01B8 (r1 HPQOEM TYLSBURG
> (XEN) HVM: VMX enabl
> ocated)
>
> (XEN) ..TIMER: vector=0x
> (XEN) DMI 2.6 present.=-1
> pin2=-1
> (XEN) Using APIC driver default ffffffff831c9
> (XEN) TSC is re
> (XEN) ACPI: PM-Timer IO Port: 0xf808
> (XEN) Boot
> (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[f804,460], pm1x_evt[f800,0]
> ÿ(XEN) Allocated console ring of 32 KiB.f
> (XEN) ACPI: wakeup_vec[bf7b880c], vec_size[20]767 microcode: CPU1 resumedENTRY ADDRESS: ffffffff81a63200
> (XEN) ACPI: Local APIC address 0xfee000007 microcode: CPU2
> resumed
> (XEN) Xen ke
> (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)Initializin
> (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr
> (XEN) Processor #6 7:10 APIC version 21u
> Linux v
> (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)080704 (Red Hat
> (XEN) Dom0 alloc.: 00000000b40000
> (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)Thu May 20 17:22:39 PDT 2010
> (XEN) Phys-Mach map: ffffffff82c1f000->ffffffff831
> (XEN)
> ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x00] disabled)
> (XEN) Start info: ffffffff831c8000->ffffffff831c8
> (XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x00] disabled)
> (XEN) Page tables: ffffffff831c9000->ffffffff831e600
> (XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x00] disabled)(XEN) Boot stack: ffffffff831e6000->ffffffff831e70000
> (XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x00] disabled)EN) TOTAL: ffffffff80000000->ffffffff83400000580
> (XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x00] disabled)) ENTRY ADDRESS: ffffffff81a63200000000f0000000 - 000000
> (XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x00] disa
>
>
>
> ma
> (XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
> initial
> Xen: setup ISA identity maps
> (XEN) ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])Initializing cgroup subsys cpuset
> (XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
> Linux version 2.6.32.13 (root@host)
> (XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge
> lint[0x1])
> RAMDISK: 02768000 - 02c1ec00
> (XEN) ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0024 (v02 HP
>
> Xen: 00000000fed45000 - 0000000
> (XEN) ACPI: IRQ9 used by override.0000bf7b8d61 00176 (v01 HPQOEM SLI
> (XEN) Enabling APIC mode: Flat. Using 3 I/O APICs
> DMI 2.6 present.
> last_
> (XEN) ACPI: HPET id: 0x8086a301 base: 0xfed00000M TYLSBURG 00000001
> 00000000)
> x86 PAT ena
> (XEN) PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 127 00000000bf7b8f0f 001B8 (v01 HPQOEM TY
> initial memory mapped : 0 -
> (XEN) PCI: MCFG area at f0000000 reserved in E820_memory_mapping: 0000000000000000-00000000b516400
> (XEN) Using ACPI (MADT) for SMP configuration information000000000 - 00b5164000 page 4k
> (XEN) Using scheduler: SMP Credit Scheduler (credit)00000-6ad000
> No NUMA co
> (XEN) Detected 2266.801 MHz processor. 02c1ec00ing a node at 00000000000000
>
> (XEN) Initing memory sharing.024 (v02
> HP
> (XEN) - MSR direct-access bitmap #0 [0000000000 - 0000001
> ACPI: F
> (XEN) HVM: ASIDs enabled.000 - 0000001000]
> (XEN) HVM: VMX enabled00000bf7b8b7c 00114 (v
> (XEN) HVM: Hardware Assisted Paging detected.031e6000] XEN PAGETABLES ==> [00031c9000 -
> (XEN) Intel machine check reporting enabled00000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00
> (XEN) I/O virtualisation disabled TRAMPOLINE ==> [0000006000 -
> (XEN) Total of 4 processors activated.MCFG 00000000bf7b8cf3 0003C (v01 HPQOE
> (XEN) ENABLING IO-APIC IRQs00000)02747680] TEXT DAT
> (XEN) -> Using new ACK method
>
>
> ÿ(XEN) Allocated console ring of 32 KiB.7b8ed7 00038 (v01 HPQOEM TYLSBURG 000000
> (XEN) microcode.c:73:d32767 microcode: CPU1 resumed
> #7
> ACPI:
> (XEN) microcode.c:73:d32767 microcode: CPU2 resumed0001 00000000)
> (XEN) Brought up 4 CPUs _ _ ___ _
>
> (XEN) microcode.c:73:d32767 microcode: CPU3 resumedM 80000001 INTL
> 20061109)
> (XEN) Turbo Mode detected! | || |_| | | | | | |
> (XEN) HPET: 4 timers in total, 0 timers will be used for broadcast |_|
> No NUMA configuration found
> /_/\_\___|_|
> Faking
> (XEN) ACPI sleep modes: S3-00000000b5164000
> (8 early reservations) ==> bootmem [0000000000 - 00b5164000]
> (XEN) PHYSICAL MEMORY ARRANGEMENT:
> #0 [000000
> (XEN) Dom0 alloc.: 00000000b4000000->00000000b8000000 (245760 pages to be allN) VGA is text mode 80x25, font
> 8x16
> #1 [00031c9000 -
> ocated)000]
> (XEN) VIRTUAL MEMORY ARRANGEMENT:0031e6000]
> (XEN) Loaded kernel: ffffffff81000000->ffffffff82768000#2 [0000006000 - 0000008000] TRAMPOLINE ==> [00000
> (XEN) Init. ramdisk: ffffffff82768000->ffffffff82c1ec00ructures
> #3 [0001000000
> (XEN) Phys-Mach map: ffffffff82c1f000->ffffffff800000000000000 -
> 000
> (XEN) 00000000f0000000 - 0
> (XEN) ENTRY ADDRESS: ffffffff81a63200d000] PGTABLE ==> [0000100000
> (XEN) Dom0 has maximum 4 VCPUs000000fed40000 (reserved)
> (XEN) Scrubbing Free RAM: ....................done.N) 00000000fed45000 - 00
> \ \/ /___ _ __ | || |
> (XEN) Xen trace buffers: disabled
> \ // _ \ '_ \
> (XEN) Std. Loglevel: All
> (XEN) Guest Loglevel: All | |__ _| |_| | |_| |OE
> (XEN) *** Serial input ->
> DOM0 (type 'CTRL-a' three times to switch input to Xen HPQOEM SLIC-WKS 20091208
>
>
> )
> (XEN) C
> Initializing cgroup subsys cpul com1=38400,8n1 console=com1
> Linux version 2.6.32.13 (root@host) (gcc version 4.1.2 20080704 (Red Hat
> est_loglvl=all
> (XEN) Video information:
> (XEN) AC
> 4.1.2-44)) #2 SMP Thu May 20 17:22:39 PDT 201016 1
> 0)
> (XEN
> Command line: ro root=/dev/sda2 console=hvc0 earlyprintk=xen nomodeset debug log (r1 HPQOEM TYLSBURG 1
> (XEN) Disc information:
> (XE
> level=10 1 MBR s
> KERNEL supported cpus:(XEN) ACPI: TCP
> (XEN)
> Intel GenuineIntelion structures 1
> AMD AuthenticAMD
> bootconsole [xenboot0] enabled
> DMI 2.6 present.
> last_pfn = 0x40000 max_arch_pfn = 0x400000000
> x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
> initial memory mapped : 0 - 20000000
> init_memory_mapping:
> 0000000000000000-0000000040000000
> 0000000000 - 0040000000 page 4k
> kernel direct mapping tables up to 40000000 @ 100000-302000
> RAMDISK: 02768000 - 02c1ec00
> ACPI: RSDP 00000000000e9010 00024 (v02 HPQOEM)
> ACPI: XSDT 00000000bf7b88e8 0006C (v01 HPQOEM SLIC-WKS 20091208 00000000)
> ACPI: FACP 00000000bf7b8a88 000F4 (v03 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: DSDT 00000000bf7b92d7 0A73D (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
> ACPI: FACS 00000000bf7b8800 00040
> ACPI: APIC 00000000bf7b8b7c 00114 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: ASF! 00000000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG
> 00000001 00000000)
> ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)
> ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: 00000000bf7b8f0f 001B8 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: SSDT 00000000bf7c4ee6 011FC (v01 INTEL PPM RCM 80000001 INTL 20061109)
> ACPI: Local APIC address 0xfee00000
> No NUMA co
>
> <stuck>
>
>
>
>
> --- On Tue, 6/15/10, Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> wrote:
>
> From: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
> Subject: Re: [Xen-devel] boot Xen 4.0
> To: "ccmail111" <ccmail111@yahoo.com>
> Cc: deshantm@gmail.com, "yingbin wang"
> <yingbin.wangyb@gmail.com>, xen-devel@lists.xensource.com
> Date: Tuesday, June 15, 2010, 5:26 PM
>
> > Linux version 2.6.32.13 (root@xyz) (gcc version 4.1.2 20080704 (Red Hat0095800 (usable)
> > (XEN) 00000
> > 4.1.2-44)) #2 SMP Thu May 20 17:22:39 PDT 2010
> >
> > Xen: 0000000000000000 - 0000000000095800
> (usable)
> > (XEN) 00000000fed45000 - 0000000100000000 (r
> > Xen: 0000000000095800 - 0000000000100000 (reserved)
> > (XEN) System RAM: 3033MB (3106320kB)
> > Xen: 0000000000100000 - 00000000b5164000 (usable)9010, 0024 (r2 HPQOEM)
> > Xen: 00000000bf7a5800 - 00000000c0000000 (reserved)PQOEM SLIC-WKS 20091208 0)
> > Xen: 00000000f0000000 - 00000000f8000000 (reserved)
> >
>
> > last_pfn = 0xb5164 max_arch_pfn = 0x400000000
> > (XEN) ACPI: APIC BF7B8B7C, 01
> > x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
> > (XE
> > initial memory mapped : 0 - 20000000OEM TYLSBURG
> 1 0)
> > init_memory_mapping: 0000000000000000-00000000b5164000
> > (XEN) ACPI: MCFG BF7B8CF3, 003C
> > 0000000000 - 00b5164000 page 4k 0)
> > kernel direct mapping tables up to b5164000 @ 100000-6ad000ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 1
> > RAMDISK: 02768000 - 02c1ec00
> > ACPI: FACS 00000000bf7b8800 00040
> > ACPI: APIC
> 00000000bf7b8b7c 00114 (v01 HPQOEM TYLSBURG 00000001 00000000)
> > ACPI: ASF! 00000000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00000001 00000000)
> > ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)
> > ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG 00000001 00000000)
> > ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)
> > ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM TYLSBURG 00000001 00000000)
> > ACPI: 00000000bf7b8f0f 001B8 (v01 HPQOEM TYLSBURG 00000001 00000000)
> > ACPI: SSDT 00000000bf7c4ee6 011FC (v01 INTEL PPM RCM 80000001 INTL 20061109)
> > ACPI: Local APIC address 0xfee00000
> > No NUMA configuration
> found
> > Faking a node at 0000000000000000-00000000b5164000
> > Bootmem setup node 0 0000000000000000-00000000b5164000
> > NODE_DATA [0000000000008000 - 000000000001ffff]
> > bootmap [0000000000020000 - 0000000000036a2f] pages 17
> > (8 early reservations) ==> bootmem [0000000000 - 00b5164000]
> > #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
> > #1 [00031c9000 - 00031e6000] XEN PAGETABLES ==> [00031c9000 - 00031e6000]
> > #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
> > #3 [0001000000 - 0002747680] TEXT DATA BSS ==> [0001000000 - 0002747680]
> > #4 [0002768000 - 0002c1ec00] RAMDISK ==> [0002768000 - 0002c1ec00]
> > #5 [0002c1f000 -
> 00031c9000] XEN START INFO ==> [0002c1f000 - 00031c9000]
> > #6 [0002748000 - 0002748120] BRK ==> [0002748000 - 0002748120]
> > #7 [0000100000 - 000068d000] PGTABLE ==> [0000100000
> >
> >
>
> This points to the E820 being wacked, but I can't see how that is
> possible considering Xen boots. Try forcing your domain to a smaller
> memory amount. Use 'dom0_mem=max:1G' in your Xen command line.
>
>
>
>
>
>
>
>
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: boot Xen 4.0
@ 2010-06-17 18:27 ccmail111
0 siblings, 0 replies; 15+ messages in thread
From: ccmail111 @ 2010-06-17 18:27 UTC (permalink / raw)
To: Konrad Rzeszutek Wilk; +Cc: deshantm, yingbin wang, xen-devel
[-- Attachment #1.1: Type: text/plain, Size: 25885 bytes --]
Thanks Konrad for your help. I tried your suggestion but see below:
Please let me know next steps..
grub entry:
title Xen 4.0 debug XenLinux 2.6
root (hd0,1)
kernel /boot/xen-4.0.0.gz noreboot dom0_mem=max:1G loglvl=all com1=38400,8n1 console=com1 iommu=off guest_loglvl=all
module /boot/vmlinuz-2.6.32.13 ro root=/dev/sda2 console=hvc0 earlyprintk=xen nomodeset debug loglevel=10
module /boot/initrd-2.6.32.13.img
(XEN) ACPI: FACP BF7B8A88, 00F4 (r3 HPQOEM TYLSBURG 1 0)EN) ACPI: ACPI SLEEP INFO: pm1x_cnt[f804,460], pm1x_evt[f800,0]
(XEN) ACPI: DSDT BF7B92D7, A73D (r1 COMPAQ DSDT_PRJ 1 MSFT 100000E) wakeup_vec[bf7b880c], vec_size[20]
(XEN) ACPI: FACS BF7B8800, 0040EN) ACPI: Local APIC address 0x
(XEN) ACPI: APIC
BF7B8B7C, 0114 (r1 HPQOEM TYLSBURG 1 0)[0x01] lapic_id[0x00] enabled)
(XEN) ACPI: ASF! BF7B8C90, 0063 (r32 HPQOEM TYLSBURG 1 0)
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
(XEN) ACPI: MCFG BF7B8CF3, 003C (r1 HPQOEM TYLSBURG 1 0)PIC
version 21
(XEN) ACPI: LAPIC (ac
(XEN) ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 1 0)
(XEN) Processor #4 7:10 APIC version 21
(XEN) ACPI: DMAR BF7B8F0F, 01B8 (r1 HPQOEM TYLSBURG 1
0)
(XEN) ACPI: LAPIC (acpi_id[0x0
(XEN) ACPI: SSDT BF7C4EE6, 11FC (r1 INTEL PPM RCM 80000001 INTL 20061109)
(XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
(XEN) No NUMA configuration found
(XEN) ACPI: LAPIC
(XEN) Faking a node at 0000000000000000-00000000bf7a5000
(XEN) ACPI: LAPI
(XEN) Domain heap initialised] disabled)
(XEN) found SMP MP-table at 000f9bf0
(XEN) ACPI: LAPIC (acpi_id[0x0b]
(XEN) DMI 2.6 present.)
(XEN) Using APIC driver default
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
(XEN) ACPI: LAPIC_NMI (acpi_
(XEN) Processor #2 7:10 APIC version
21
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)nt[0x1])
(XEN) Processor #4 7:10 APIC version 21[0x04] high edge lint[
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)MI (acpi_id[0x07] high edge lint[0x1])
(XEN) ACPI:
LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)MI (acpi_id[0x08] high edge lint[0x1])
(XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)(id[0x01] address[0xfec00000] gsi_base[0])
(XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)C[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x00] disabled)
(XEN) ACPI: IOAPIC (id[0x02] address[0xfec1000
(XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x00] disabled)
(XEN) IOAPIC[1]: apic_id 2, version
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x00]
disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x00] disabled)NT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x00] disabled)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
(XEN) ACPI: IRQ9 used by overri
(XEN) ACPI: LAPIC_NMI
(acpi_id[0x02] high edge lint[0x1])mode: Flat. Using 3 I/O APICs
(XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])base: 0xfed00000
(XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0 se
(XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge
lint[0x1])
(XEN) Using sch
(XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
(XEN) Detected 2266.814 M
(XEN) ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])Initing memory sharing.
(XEN
(XEN) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
(XEN) - APIC MMIO
access virtualisation
(XEN) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
(XEN) - Extended Page Tables (EPT)
(XEN) ACPI: IOAPIC (id[0x02] address[0xfec10000] gsi_base[24])
(XEN) - Virtual N
(XEN) IOAPIC[1]: apic_id 2, version 32, address 0xfec10000, GSI 24-47
(XEN) HVM: ASIDs
enabled.
(XEN) TSC is reliable, synchroniz
(XEN) ACPI: IRQ2 used by override.
(
(XEN) ACPI: IRQ9 used by override.ET
(XEN) Enabling APIC mode: Flat. Using 3 I/O APICs
(XEN) microcode
(XEN) ACPI: HPET id: 0x8086a301
base: 0xfed00000
(XEN) mic
(XEN) PCI: MCFG configuration 0: base f0000000 se
(XEN) *** LOADING DOMAIN 0 ***
(XEN) - APIC MMIO access virtualisationernel: 64-bit, lsb, compat32
(XEN) - APIC TPR shadow
(XEN) Dom0 kernel:
(XEN) - Extended Page Tables (EPT)>
0x2768000
(XEN) - Virtual-Processor Identifiers (VPID)N) PHYSICAL MEMORY ARRANGEMENT:
(XEN) - Virtual NMI(XEN) Dom0 alloc.:
(XEN) - MSR direct-access bitmap00 (725348 pages to be all
(XEN) HVM: ASIDs enabled.
(XEN) HVM: VMX enabl
ocated)
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK
method
(XEN) Phys
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1dfdd
(XEN) TSC is reliable, synchronization unnecessaryN) Start info: ffffffff831c8000->ffffffff831c8
(XEN) Platform timer is 14.318MHz HPET
üHòÆõ ÿþüiþ
ÿ(XEN) Allocated console ring of 32 KiB.
(XEN) Page tables:
ffffffff831c9000-
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
\ \/ /___ _ __ | || | / _
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed
(XEN) ACPI sleep modes: S3f81a63200
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) Dom0 has maximum 4 VCPUs
(XEN) *** LOADING DOMAIN 0 ***XEN) Freed 156kB init memory.
(XEN) Xen kernel: 64-bit, lsb, compat32 kernel into physical memoryfer time: 1 s
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x2768000etup ISA identity maps
(XEN) Disc info
(XEN) PHYSICAL MEMORY ARRANGEMENT:d...
(XEN)
(XEN) Dom0 alloc.: 00000000b4000000->00000000b8000000 (725348 pages to be all
(XEN) Found 1 EDD info
Initializing cgroup
s
ocated)
(XEN)
(XEN) Phys-Mach map: ffffffff82c1f000->ffffffff831c7b20fsdffsfsfsfsfsdfdd
Xen: 0000000000095800 - 0000000000100000 (reserved)
hello fsdffsf
(XEN) Start info: ffffffff831c8000->ffffffff831c84b4fdd
Xen: 0000000000100000 - 00000000
üHòÆõ ÿþüiþ¿¯óÅÿçü __ __ (r2 HPQOEM)
(XEN) Page tables: ffffffff831c9000->ffffffff831e6000
Xen: 00000000bf7a5800 -
00000000c0000000 (reserved)PQ
\ \/ /___ _ __ | || | / _ 0)
/_/\_\___|_| |_| |_|(_)7010600070106
(XEN) ENTRY ADDRESS: ffffffff81a63200
(XE
initial memory mapped
(XEN) Xen version 4.0.0 (sun 1 0)
(XEN) Dom0 has maximum 4 VCPUs
(XEN) Freed 156kB init
memory.00000000000-00000000b5164000
(X
mapping kernel into physical memoryfer time: 1 secondsCPI: MCFG BF7B8CF3, 003C
Xen: setup ISA identity mapsge 4k 0)
(XEN) Disc info
k
about to get started...les up to b5164000 @ 10
(XEN) Found 1: TCPA BF7B8D2
Initializing cgroup subsys cpuset 1
(XEN) Found 1 EDD
info
Initializing cgroup s
Xen: 0000000000000000 - 0000000000095800 (usable)0000000)
(XEN) 00000000fed45000 - 0000000100000000 (rG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG
Xen: 0000000000095800 - 0000000000100000
(reserved)
AC
(XEN) System RAM: 3033MB (3106320kB)HPQOEM TYLSBURG 00000001 000000
Xen: 0000000000100000 - 00000000b5164000 (usable)9010, 0024 (r2 HPQOEM)
ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001
Xen: 00000000bf7a5800 - 00000000c0000000 (reserved)PQOEM SLIC-WKS 20091208 0)
ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM
TYLS
x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106: Local APIC address 0xfee00000APIC address 0xfee00000
(XE
No
initial memory mapped : 0 - 20000000OEM TYLSBURG 1 0)0000000000000-00000000b5164000
(XEN)
init_memory_mapping: 0000000000000000-00000000b5164000b5164000
(XEN) ACPI: LAPIC
(acpi_id[0x02] la
(XEN) ACPI: MCFG BF7B8CF3, 003C008000 - 000000000001ffff]
0000000000 - 00b5164000 page 4k 0)
bootmap [0000000000020000 - 000000000
kernel direct mapping tables up to b5164000 @ 100000-6ad000ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 10000000 - 00b5164000]or #4 7:10 APIC version 21
ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)002747680] ACPI: LAPIC
(acpi_id[0x08] lapic_id[0x00] disabled)
ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG 00000001 00000000)2c1ec00]0] disabled)
ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)c9000]
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[
ACPI: HPET 00000000bf7b8ed7 00038
(v01 HPQOEM TYLSRK
No NUMA configuration found
(XEN) ACPI: LAPIC (acpi_i
Faking a node at 0000000000000000-00000000b51640000] lapic_id[0x00] disabled)
(XEN) Process
Bootmem setup node 0 0000000000000000-00000000b5164000I (acpi_id
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0
NODE_DATA [0000000000008000 - 000000000001ffff]I: LAPIC_NMI (acpi_
(XEN) Processor #2 7:10 APIC
bootmap [0000000000020000 - 0000000000036a2f] pages 17PI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)nt[0x1])
(8 early reservations) ==> bootmem [0000000000 - 00b5164000]or #4 7:10 APIC version 21[0x04] high edge
lint[
#3 [0001000000 - 0002747680] TEXT DATA BSS ==> [0001000000 - 0002747680] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)C[0]: apic_id 1, version
#4 [0002768000 - 0002c1ec00] RAMDISK ==> [0002768000 - 0002c1ec00]0] disabled)
(XEN) ACPI: IOAPIC (id[0x02] address[0xfec1000
(XEN) A
#5 [0002c1f000 - 00031c9000] XEN START INFO ==> [0002c1f000 - 00031c9000]OAPIC[1]: apic_id 2, version
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x00]
#6 [0002748000 - 0002748120] BRK
(XEN) ACPI:
/_/\_\___|_| |_| |_|(_)___(_)___/
(XEN) ACPI: LAPIC_NMI (acpi_id[0
(XEN) Xen version 4.0.0 (@) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-44
(XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])mode: Flat. Using 3
)) Tue Jun 8 15:44:03 PDT 2010
(XEN) ACPI: LAPIC_NMI (acpi
(XEN) Latest ChangeSet: unavailable0xfed00000
(XEN) Command line: noreboot dom0_mem=max:1G loglvl=all com1ge lint[0
se
(XEN) Found 1 MBR signatureshigh edge lint[0x1])Initing m
(XEN) Found 1 EDD information structures
(XEN
(XEN) ACPI: IOAPIC (id[0x01] addre
(XEN) Xen-e820 RAM map:0])
(XEN)
(XEN) 0000000000000000 - 0000000000095800 (usable)IC[0]: apic_id 1, version 32, address 0xfec00000, G
(XEN) 0000000000095800 - 00000000000a0000 (reserved))
(XEN) ACPI: IOAPIC (id[0x02] ad
(XEN) 00000000000e8000 - 0000000000100000
(reserved)
(XEN) - Virtual N
(XEN) IOAPIC[
(XEN) 0000000000100000 - 00000000bf7a5800 (usable)4-47
(XEN) HVM: ASIDs enabled.
(XEN) 00000000bf7a5800 - 00000
(XEN) ACPI: APIC BF7B8B7C, 0114 (r1 HPQOEM TYLSBURG 1 0)microcode: CPU3 resumed
(XEN) Using ACPI (MADT) for SMP configuration infor
(XEN) ACPI: ASF! BF7B8C90, 0063 (r32 HPQOEM TYLSBURG
1 0)cheduler: SMP Credit Scheduler (credit)ast
(XEN) ACPI: MCFG BF7B8CF3, 003C (r1 HPQOEM TYLSBURG 1 0)
(XEN)
(XEN) Initing memory sharing.ling timer started.
(XEN) ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 1 0)
(XEN) - APIC MMIO access virtualisationernel: 64-bit, lsb, compat32
(XEN) ACPI: SLIC BF7B8D61,
0176 (r1 HPQOEM SLIC-WKS 1 0) Page Tables (EPT)> 0x2768000
(XEN) - Virtual-Proc
(XEN) ACPI: HPET BF7B8ED7, 0038 (r1 HPQOEM TYLSBURG 1 0) - Virtual NMI(XEN) Dom0 alloc.:
(XEN) - MSR direct-access bitmap00 (725
(XEN) ACPI: DMAR BF7B8F0F, 01B8 (r1 HPQOEM TYLSBURG
(XEN) HVM: VMX enabl
ocated)
(XEN) ..TIMER: vector=0x
(XEN) DMI 2.6 present.=-1
pin2=-1
(XEN) Using APIC driver default ffffffff831c9
(XEN) TSC is re
(XEN) ACPI: PM-Timer IO Port: 0xf808
(XEN) Boot
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[f804,460], pm1x_evt[f800,0]
ÿ(XEN) Allocated console ring of 32 KiB.f
(XEN) ACPI: wakeup_vec[bf7b880c], vec_size[20]767 microcode: CPU1 resumedENTRY ADDRESS: ffffffff81a63200
(XEN) ACPI: Local APIC address 0xfee000007 microcode: CPU2
resumed
(XEN) Xen ke
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)Initializin
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr
(XEN) Processor #6 7:10 APIC version 21u
Linux v
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)080704 (Red Hat
(XEN) Dom0 alloc.: 00000000b40000
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)Thu May 20 17:22:39 PDT 2010
(XEN) Phys-Mach map: ffffffff82c1f000->ffffffff831
(XEN)
ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x00] disabled)
(XEN) Start info: ffffffff831c8000->ffffffff831c8
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x00] disabled)
(XEN) Page tables: ffffffff831c9000->ffffffff831e600
(XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x00] disabled)(XEN) Boot stack: ffffffff831e6000->ffffffff831e70000
(XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x00] disabled)EN) TOTAL: ffffffff80000000->ffffffff83400000580
(XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x00] disabled)) ENTRY ADDRESS: ffffffff81a63200000000f0000000 - 000000
(XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x00] disa
ma
(XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
initial
Xen: setup ISA identity maps
(XEN) ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])Initializing cgroup subsys cpuset
(XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
Linux version 2.6.32.13 (root@host)
(XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge
lint[0x1])
RAMDISK: 02768000 - 02c1ec00
(XEN) ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0024 (v02 HP
Xen: 00000000fed45000 - 0000000
(XEN) ACPI: IRQ9 used by override.0000bf7b8d61 00176 (v01 HPQOEM SLI
(XEN) Enabling APIC mode: Flat. Using 3 I/O APICs
DMI 2.6 present.
last_
(XEN) ACPI: HPET id: 0x8086a301 base: 0xfed00000M TYLSBURG 00000001
00000000)
x86 PAT ena
(XEN) PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 127 00000000bf7b8f0f 001B8 (v01 HPQOEM TY
initial memory mapped : 0 -
(XEN) PCI: MCFG area at f0000000 reserved in E820_memory_mapping: 0000000000000000-00000000b516400
(XEN) Using ACPI (MADT) for SMP configuration information000000000 - 00b5164000 page 4k
(XEN) Using scheduler: SMP Credit Scheduler (credit)00000-6ad000
No NUMA co
(XEN) Detected 2266.801 MHz processor. 02c1ec00ing a node at 00000000000000
(XEN) Initing memory sharing.024 (v02
HP
(XEN) - MSR direct-access bitmap #0 [0000000000 - 0000001
ACPI: F
(XEN) HVM: ASIDs enabled.000 - 0000001000]
(XEN) HVM: VMX enabled00000bf7b8b7c 00114 (v
(XEN) HVM: Hardware Assisted Paging detected.031e6000] XEN PAGETABLES ==> [00031c9000 -
(XEN) Intel machine check reporting enabled00000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00
(XEN) I/O virtualisation disabled TRAMPOLINE ==> [0000006000 -
(XEN) Total of 4 processors activated.MCFG 00000000bf7b8cf3 0003C (v01 HPQOE
(XEN) ENABLING IO-APIC IRQs00000)02747680] TEXT DAT
(XEN) -> Using new ACK method
ÿ(XEN) Allocated console ring of 32 KiB.7b8ed7 00038 (v01 HPQOEM TYLSBURG 000000
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
#7
ACPI:
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed0001 00000000)
(XEN) Brought up 4 CPUs _ _ ___ _
(XEN) microcode.c:73:d32767 microcode: CPU3 resumedM 80000001 INTL
20061109)
(XEN) Turbo Mode detected! | || |_| | | | | | |
(XEN) HPET: 4 timers in total, 0 timers will be used for broadcast |_|
No NUMA configuration found
/_/\_\___|_|
Faking
(XEN) ACPI sleep modes: S3-00000000b5164000
(8 early reservations) ==> bootmem [0000000000 - 00b5164000]
(XEN) PHYSICAL MEMORY ARRANGEMENT:
#0 [000000
(XEN) Dom0 alloc.: 00000000b4000000->00000000b8000000 (245760 pages to be allN) VGA is text mode 80x25, font
8x16
#1 [00031c9000 -
ocated)000]
(XEN) VIRTUAL MEMORY ARRANGEMENT:0031e6000]
(XEN) Loaded kernel: ffffffff81000000->ffffffff82768000#2 [0000006000 - 0000008000] TRAMPOLINE ==> [00000
(XEN) Init. ramdisk: ffffffff82768000->ffffffff82c1ec00ructures
#3 [0001000000
(XEN) Phys-Mach map: ffffffff82c1f000->ffffffff800000000000000 -
000
(XEN) 00000000f0000000 - 0
(XEN) ENTRY ADDRESS: ffffffff81a63200d000] PGTABLE ==> [0000100000
(XEN) Dom0 has maximum 4 VCPUs000000fed40000 (reserved)
(XEN) Scrubbing Free RAM: ....................done.N) 00000000fed45000 - 00
\ \/ /___ _ __ | || |
(XEN) Xen trace buffers: disabled
\ // _ \ '_ \
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All | |__ _| |_| | |_| |OE
(XEN) *** Serial input ->
DOM0 (type 'CTRL-a' three times to switch input to Xen HPQOEM SLIC-WKS 20091208
)
(XEN) C
Initializing cgroup subsys cpul com1=38400,8n1 console=com1
Linux version 2.6.32.13 (root@host) (gcc version 4.1.2 20080704 (Red Hat
est_loglvl=all
(XEN) Video information:
(XEN) AC
4.1.2-44)) #2 SMP Thu May 20 17:22:39 PDT 201016 1
0)
(XEN
Command line: ro root=/dev/sda2 console=hvc0 earlyprintk=xen nomodeset debug log (r1 HPQOEM TYLSBURG 1
(XEN) Disc information:
(XE
level=10 1 MBR s
KERNEL supported cpus:(XEN) ACPI: TCP
(XEN)
Intel GenuineIntelion structures 1
AMD AuthenticAMD
bootconsole [xenboot0] enabled
DMI 2.6 present.
last_pfn = 0x40000 max_arch_pfn = 0x400000000
x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
initial memory mapped : 0 - 20000000
init_memory_mapping:
0000000000000000-0000000040000000
0000000000 - 0040000000 page 4k
kernel direct mapping tables up to 40000000 @ 100000-302000
RAMDISK: 02768000 - 02c1ec00
ACPI: RSDP 00000000000e9010 00024 (v02 HPQOEM)
ACPI: XSDT 00000000bf7b88e8 0006C (v01 HPQOEM SLIC-WKS 20091208 00000000)
ACPI: FACP 00000000bf7b8a88 000F4 (v03 HPQOEM TYLSBURG 00000001 00000000)
ACPI: DSDT 00000000bf7b92d7 0A73D (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
ACPI: FACS 00000000bf7b8800 00040
ACPI: APIC 00000000bf7b8b7c 00114 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: ASF! 00000000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00000001 00000000)
ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG
00000001 00000000)
ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)
ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: 00000000bf7b8f0f 001B8 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: SSDT 00000000bf7c4ee6 011FC (v01 INTEL PPM RCM 80000001 INTL 20061109)
ACPI: Local APIC address 0xfee00000
No NUMA co
<stuck>
--- On Tue, 6/15/10, Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> wrote:
From: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Subject: Re: [Xen-devel] boot Xen 4.0
To: "ccmail111" <ccmail111@yahoo.com>
Cc: deshantm@gmail.com, "yingbin wang"
<yingbin.wangyb@gmail.com>, xen-devel@lists.xensource.com
Date: Tuesday, June 15, 2010, 5:26 PM
> Linux version 2.6.32.13 (root@xyz) (gcc version 4.1.2 20080704 (Red Hat0095800 (usable)
> (XEN) 00000
> 4.1.2-44)) #2 SMP Thu May 20 17:22:39 PDT 2010
>
> Xen: 0000000000000000 - 0000000000095800
(usable)
> (XEN) 00000000fed45000 - 0000000100000000 (r
> Xen: 0000000000095800 - 0000000000100000 (reserved)
> (XEN) System RAM: 3033MB (3106320kB)
> Xen: 0000000000100000 - 00000000b5164000 (usable)9010, 0024 (r2 HPQOEM)
> Xen: 00000000bf7a5800 - 00000000c0000000 (reserved)PQOEM SLIC-WKS 20091208 0)
> Xen: 00000000f0000000 - 00000000f8000000 (reserved)
>
> last_pfn = 0xb5164 max_arch_pfn = 0x400000000
> (XEN) ACPI: APIC BF7B8B7C, 01
> x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
> (XE
> initial memory mapped : 0 - 20000000OEM TYLSBURG
1 0)
> init_memory_mapping: 0000000000000000-00000000b5164000
> (XEN) ACPI: MCFG BF7B8CF3, 003C
> 0000000000 - 00b5164000 page 4k 0)
> kernel direct mapping tables up to b5164000 @ 100000-6ad000ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 1
> RAMDISK: 02768000 - 02c1ec00
> ACPI: FACS 00000000bf7b8800 00040
> ACPI: APIC
00000000bf7b8b7c 00114 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: ASF! 00000000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)
> ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: 00000000bf7b8f0f 001B8 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: SSDT 00000000bf7c4ee6 011FC (v01 INTEL PPM RCM 80000001 INTL 20061109)
> ACPI: Local APIC address 0xfee00000
> No NUMA configuration
found
> Faking a node at 0000000000000000-00000000b5164000
> Bootmem setup node 0 0000000000000000-00000000b5164000
> NODE_DATA [0000000000008000 - 000000000001ffff]
> bootmap [0000000000020000 - 0000000000036a2f] pages 17
> (8 early reservations) ==> bootmem [0000000000 - 00b5164000]
> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
> #1 [00031c9000 - 00031e6000] XEN PAGETABLES ==> [00031c9000 - 00031e6000]
> #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
> #3 [0001000000 - 0002747680] TEXT DATA BSS ==> [0001000000 - 0002747680]
> #4 [0002768000 - 0002c1ec00] RAMDISK ==> [0002768000 - 0002c1ec00]
> #5 [0002c1f000 -
00031c9000] XEN START INFO ==> [0002c1f000 - 00031c9000]
> #6 [0002748000 - 0002748120] BRK ==> [0002748000 - 0002748120]
> #7 [0000100000 - 000068d000] PGTABLE ==> [0000100000
>
>
This points to the E820 being wacked, but I can't see how that is
possible considering Xen boots. Try forcing your domain to a smaller
memory amount. Use 'dom0_mem=max:1G' in your Xen command line.
[-- Attachment #1.2: Type: text/html, Size: 50551 bytes --]
[-- Attachment #2: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 15+ messages in thread* Re: boot Xen 4.0
@ 2010-06-10 16:02 ccmail111
2010-06-15 21:26 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 15+ messages in thread
From: ccmail111 @ 2010-06-10 16:02 UTC (permalink / raw)
To: Konrad Rzeszutek Wilk; +Cc: deshantm, yingbin wang, xen-devel
[-- Attachment #1.1: Type: text/plain, Size: 40665 bytes --]
Here is complete serial console log:
XEN) ACPI: PM-Timer IO Port: 0xf808
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[f804,460], pm1x_evt[f800,0]
(XEN) ACPI: wakeup_vec[bf7b880c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
(XEN) Processor #2 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
(XEN) Processor #4 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
(XEN) Processor #6 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[
(XEN) ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
(XEN) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: IOAPIC (id[0x02] address[0xfec10000] gsi_base[24])
(XEN) IOAPIC[1]: apic_id 2, version 32, address 0xfec10000, GSI 24-47
(XEN) ACPI: IOAPIC (id[0x03] address[0xfec20000] gsi_base[48])
(XEN) IOAPIC[2]: apic_id 3, version 32, address 0xfec20000, GSI 48-71
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 3 I/O APICs
(XEN) ACPI: HPET id: 0x8086a301 base: 0xfed00000
(XEN) PCI: MCFG configuration 0: base f0000000 se
(XEN) PCI: MCFG area at f0000000 reserved in E820
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 2266.795 MHz processor.
(XEN) Initing memory sharing.
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Extended Page Tables (EPT)
(XEN) - Virtual-Processor Identifiers (VPID)
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: ASIDs enabled.
(XEN) HVM: VMX enabl
(XEN) HVM: Hardware Assisted Paging detected.
(XEN) Intel machine check reporting enabled
(XEN) I/O virtualisation disabled
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) TSC is reliable, synchronization unnecessary
(XEN) Platform timer is 14.318MHz HPET
ÿ(XEN) Allocated console ring of 32 KiB.
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed
(XEN) Brought up 4 CPUs
(XEN) microcode.c:73:d32767 microcode: CPU3 resumed
(XEN) Turbo Mode detected!
(XEN) HPET: 4 timers in total, 0 timers will be used for broadcast
(XEN) ACPI sleep modes: S3
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x2768000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 00000000b4000000->00000000b8000000 (725348 pages to be all
ocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff81000000->ffffffff82768000
(XEN) Init. ramdisk: ffffffff82768000->ffffffff82c1ec00
(XEN) Phys-Mach map: ffffffff82c1f000->ffffffff831c7b20
(XEN) Start info: ffffffff831c8000->ffffffff831c84b4
(XEN) Page tables: ffffffff831c9000->ffffffff831e6000
(XEN) Boot stack: ffffffff831e6000->ffffffff831e7000
(XEN) TOTAL: ffffffff80000000->ffffffff83400000
(XEN) ENTRY ADDRESS: ffffffff81a63200
(XEN) Dom0 has maximum 4 VCPUs
(XEN) Scrubbing Free RAM: .done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen
)
(XEN) Freed 156kB init memory.
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.32.13 (root@xyz) (gcc version 4.1.2 20080704 (Red Hat
4.1.2-44)) #2 SMP Thu May 20 17:22:39 PDT 2010
Command line: ro root=/dev/sda2 console=hvc0 earlyprintk=xen nomodeset debug log
level=10
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
released 0 pages of unused memory
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 0000000000095800 (usable)
Xen: 0000000000095800 - 0000000000100000 (reserved)
Xen: 0000000000100000 - 00000000b5164000 (usable)
Xen: 00000000bf7a5800 - 00000000c0000000 (reserved)
Xen: 00000000f0000000 - 00000000f8000000 (reserved)
Xen: 00000000fec00000 - 00000000fed40000 (reserved)
Xen: 00000000fed45000 - 0000000100000000 (reserved)
bootconsole [xenboot0] enabled
DMI 2.6 present.
last_pfn = 0xb5164 max_arch_pfn = 0x400000000
x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-00000000b5164000
0000000000 - 00b5164000 page 4k
kernel direct mapping tables up to b5164000 @ 100000-6ad000
RAMDISK: 02768000 - 02c1ec00
ACPI: RSDP 00000000000e9010 00024 (v02 HP
ACPI: XSDT 00000000bf7b88e8 0006C (v01 HPQOEM SLIC-WKS 20091208 00000000)
ACPI: FACP 00000000bf7b8a88 000F4 (v03 HPQOEM TYLSBURG 00000001 00000000)
ACPI: DSDT 00000000bf7b92d7 0A73D (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
ACPI: FACS 00000000bf7b8800 00040
ACPI: APIC 00000000bf7b8b7c 00114 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: ASF! 00000000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00000001 00000000)
ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)
ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: 00000000bf7b8f0f 001B8 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: SSDT 00000000bf7c4ee6 011FC (v01 INTEL PPM RCM 80000001 INTL 20061109)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-00000000b5164000
Bootmem setup node 0 0000000000000000-00000000b5164000
NODE_DATA [0000000000008000 - 000000000001ffff]
bootmap [0000000000020000 - 0000000000036a2f] pages 17
(8 early reservations) ==> bootmem [0000000000 - 00b5164000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [00031c9000 - 00031e6000] XEN PAGETABLES ==> [00031c9000 - 00031e6000]
#2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#3 [0001000000 - 0002747680] TEXT DATA BSS ==> [00010
#4 [0002768000 - 0002c1ec00] RAMDISK ==> [0002768000 - 0002c1ec00]
#5 [0002c1f000 - 00031c9000] XEN START INFO ==> [0002c1f000 - 00031c9000]
#6 [0002748000 - 0002748120] BRK ==> [0002748000 - 0002748120]
#7 [0000100000 - 000068d000] PGTABLE ==> [0000100000
ÿ __ __ _ _ ___ ___
\ \/ /___ _ __ | || | / _ \ / _ \
\ // _ \ '_ \ | || |_| | | | | | |
/ \ __/ | | | |__ _| |_| | |_| |
/_/\_\___|_| |_| |_|(_)___(_)___/
(XEN) Xen version 4.0.0 (root@) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-44
)) Tue Jun 8 15:44:03 PDT 2010
(XEN) Latest ChangeSet: unavailable
(XEN) Command line: noreboot loglvl=all com1=38400,8n1 console=com1 iommu=off gu
est_loglvl=all
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: V2; EDID transfer time: 1 seconds
(XEN) Disc information:
(XEN) Found 1 MBR signatures
(XEN) Found 1 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000
(XEN) 0000000000095800 - 00000000000a0000 (reserved)
(XEN) 00000000000e8000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bf7a5800 (usable)
(XEN) 00000000bf7a5800 - 00000000c0000000 (reserved)
(XEN) 00000000f0000000 - 00000000f8000000 (reserved)
(XEN) 00000000fec00000 - 00000000fed40000 (reserved)
(XEN) 00000000fed45000 - 0000000100000000 (reserved)
(XEN) System RAM: 3033MB (3106320kB)
(XEN) ACPI: RSDP 000E9010, 0024 (r2 HPQOEM)
(XEN) ACPI: XSDT BF7B88E8, 006C (r1 HPQOEM SLIC-WKS 20091208
(XEN) ACPI: FACP BF7B8A88, 00F4 (r3 HPQOEM TYLSBURG 1 0)
(XEN) ACPI: DSDT BF7B92D7, A73D (r1 COMPAQ DSDT_PRJ 1 MSFT 100000E)
(XEN) ACPI: FACS BF7B8800, 0040
(XEN) ACPI: APIC BF7B8B7C, 0114 (r1 HPQOEM TYLSBURG 1 0)
(XEN) ACPI: ASF! BF7B8C90, 0063 (r32 HPQOEM TYLSBURG 1 0)
(XEN) ACPI: MCFG BF7B8CF3, 003C (r1 HPQOEM TYLSBURG 1 0)
(XEN) ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 1 0)
(XEN) ACPI: SLIC BF7B8D61, 0176 (r1 HPQOEM SLIC-WKS 1 0)
(XEN) ACPI: HPET BF7B8ED7, 0038 (r1 HPQOEM TYLSBURG 1 0)
(XEN) ACPI: DMAR BF7B8F0F, 01B8 (r1 HPQOEM TYLSBURG 1 0)
(XEN) ACPI: SSDT BF7C4EE6, 11FC (r1 INTEL PPM RCM 80000001 INTL 20061109)
(XEN) No NUMA configuration found
(XEN) Faking a node at 0000000000000000-00000000bf7a5000
(XEN) Domain heap initialised
(XEN) found SMP MP-table at 000f9bf0
(XEN) DMI 2.6 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0xf808
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[f804,460], pm1x_evt[f800,0]
(XEN) ACPI: wakeup_vec[bf7b880c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
(XEN) Processor #2 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
(XEN) Processor #4 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
(XEN) Processor #6 7:10 APIC version 21
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x09] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x10] lapic_id[0x00] disabled)
(XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[
(XEN) ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
(XEN) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: IOAPIC (id[0x02] address[0xfec10000] gsi_base[24])
(XEN) IOAPIC[1]: apic_id 2, version 32, address 0xfec10000, GSI 24-47
(XEN) ACPI: IOAPIC (id[0x03] address[0xfec20000] gsi_base[48])
(XEN) IOAPIC[2]: apic_id 3, version 32, address 0xfec20000, GSI 48-71
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 3 I/O APICs
(XEN) ACPI: HPET id: 0x8086a301 base: 0xfed00000
(XEN) PCI: MCFG configuration 0: base f0000000 se
(XEN) PCI: MCFG area at f0000000 reserved in E820
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 2266.814 MHz processor.
(XEN) Initing memory sharing.
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Extended Page Tables (EPT)
(XEN) - Virtual-Processor Identifiers (VPID)
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: ASIDs enabled.
(XEN) HVM: VMX enabl
(XEN) HVM: Hardware Assisted Paging detected.
(XEN) Intel machine check reporting enabled
(XEN) I/O virtualisation disabled
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) TSC is reliable, synchronization unnecessary
(XEN) Platform timer is 14.318MHz HPET
ÿ(XEN) Allocated console ring of 32 KiB.
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed
(XEN) Brought up 4 CPUs
(XEN) microcode.c:73:d32767 microcode: CPU3 resumed
(XEN) Turbo Mode detected!
(XEN) HPET: 4 timers in total, 0 timers will be used for broadcast
(XEN) ACPI sleep modes: S3
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x2768000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 00000000b4000000->00000000b8000000 (725348 pages to be all
ocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
hello fsdffsfsfsf
(XEN) Loaded kernel: ffffffff81000000->ffffffff82768000
hello fsdffsfsfsfsfsdfdd
(XEN) Init. ramdisk: ffffffff82768000->ffffffff82c1ec00
hello fsdffsfsfsfsfsdfdd
(XEN) Phys-Mach map: ffffffff82c1f000->ffffffff831c7b20fsdffsfsfsfsfsdfdd
hello fsdffsf
(XEN) Start info: ffffffff831c8000->ffffffff831c84b4fdd
üHòÆõ ÿþüiþ\x1c¿¯óÅÿçü __ __
(XEN) Page tables: ffffffff831c9000->ffffffff831e6000
\ \/ /___ _ __ | || | / _
(XEN) Boot stack: ffffffff831e6000->ffffffff831e7000'_ \ | || |_| | | | | | |
(XEN) TOTAL: ffffffff80000000->ffffffff83400000
/_/\_\___|_| |_| |_|(_)
(XEN) ENTRY ADDRESS: ffffffff81a63200
(XEN) Xen version 4.0.0 (sun
(XEN) Dom0 has maximum 4 VCPUs
(XEN) Freed 156kB init memory.
(X
mapping kernel into physical memoryfer time: 1 seconds
Xen: setup ISA identity maps
(XEN) Disc info
about to get started...
(XEN) Found 1
Initializing cgroup subsys cpuset
(XEN) Found 1 EDD info
Initializing cgroup subsys cpu
(
Linux version 2.6.32.13 (root@xyz) (gcc version 4.1.2 20080704 (Red Hat0095800 (usable)
(XEN) 00000
4.1.2-44)) #2 SMP Thu May 20 17:22:39 PDT 2010
Xen: 0000000000000000 - 0000000000095800 (usable)
(XEN) 00000000fed45000 - 0000000100000000 (r
Xen: 0000000000095800 - 0000000000100000 (reserved)
(XEN) System RAM: 3033MB (3106320kB)
Xen: 0000000000100000 - 00000000b5164000 (usable)9010, 0024 (r2 HPQOEM)
Xen: 00000000bf7a5800 - 00000000c0000000 (reserved)PQOEM SLIC-WKS 20091208 0)
Xen: 00000000f0000000 - 00000000f8000000 (reserved)
last_pfn = 0xb5164 max_arch_pfn = 0x400000000
(XEN) ACPI: APIC BF7B8B7C, 01
x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
(XE
initial memory mapped : 0 - 20000000OEM TYLSBURG 1 0)
init_memory_mapping: 0000000000000000-00000000b5164000
(XEN) ACPI: MCFG BF7B8CF3, 003C
0000000000 - 00b5164000 page 4k 0)
kernel direct mapping tables up to b5164000 @ 100000-6ad000ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 1
RAMDISK: 02768000 - 02c1ec00
ACPI: FACS 00000000bf7b8800 00040
ACPI: APIC 00000000bf7b8b7c 00114 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: ASF! 00000000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00000001 00000000)
ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)
ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: 00000000bf7b8f0f 001B8 (v01 HPQOEM TYLSBURG 00000001 00000000)
ACPI: SSDT 00000000bf7c4ee6 011FC (v01 INTEL PPM RCM 80000001 INTL 20061109)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-00000000b5164000
Bootmem setup node 0 0000000000000000-00000000b5164000
NODE_DATA [0000000000008000 - 000000000001ffff]
bootmap [0000000000020000 - 0000000000036a2f] pages 17
(8 early reservations) ==> bootmem [0000000000 - 00b5164000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [00031c9000 - 00031e6000] XEN PAGETABLES ==> [00031c9000 - 00031e6000]
#2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#3 [0001000000 - 0002747680] TEXT DATA BSS ==> [0001000000 - 0002747680]
#4 [0002768000 - 0002c1ec00] RAMDISK ==> [0002768000 - 0002c1ec00]
#5 [0002c1f000 - 00031c9000] XEN START INFO ==> [0002c1f000 - 00031c9000]
#6 [0002748000 - 0002748120] BRK ==> [0002748000 - 0002748120]
#7 [0000100000 - 000068d000] PGTABLE ==> [0000100000
Kindly suggest..
Thanks !
CM
--- On Fri, 6/4/10, Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> wrote:
From: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Subject: Re: [Xen-devel] boot Xen 4.0
To: "ccmail111" <ccmail111@yahoo.com>
Cc: "Pasi Kärkkäinen" <pasik@iki.fi>, deshantm@gmail.com, "yingbin wang" <yingbin.wangyb@gmail.com>, xen-devel@lists.xensource.com
Date: Friday, June 4, 2010, 4:34 PM
On Fri, Jun 04, 2010 at 01:30:06PM -0700, ccmail111 wrote:
> Hi Pasi,
>
> Here is output of serial console where I see Xen4.0 stuck during boot up:
There has to be more.. What happend with the Xen banner?
>
> (XEN) *** LOADING DOMAIN 0 ***
> (XEN) Xen kernel: 64-bit, lsb, compat32
> (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 ->
0x2768000
> (XEN) PHYSICAL MEMORY ARRANGEMENT:
> (XEN) Dom0 alloc.: 00000000b4000000->00000000b8000000 (725348 pages to be
all
> ocated)
> (XEN) VIRTUAL MEMORY ARRANGEMENT:
> (XEN) Loaded kernel:
ffffffff81000000->ffffffff82768000
> (XEN) Init. ramdisk: ffffffff82768000->ffffffff82c1ec00
> (XEN) Phys-Mach map:
ffffffff82c1f000->ffffffff831c7b20
> (XEN) Start info: ffffffff831c8000->ffffffff831c84b4
> (XEN) Page tables:
ffffffff831c9000->ffffffff831e6000
> (XEN) Boot stack: ffffffff831e6000->ffffffff831e7000
> (XEN) TOTAL:
ffffffff80000000->ffffffff83400000
> (XEN) ENTRY ADDRESS: ffffffff81a63200
> (XEN) Dom0 has maximum 4 VCPUs
> (XEN) Scrubbing Free RAM:
.done.
> (XEN) Xen trace buffers: disabled
> (XEN) Std. Loglevel: All
> (XEN) Guest Loglevel: All
> (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to
Xen
> )
> (XEN) Freed 156kB init memory.
> mapping kernel into physical memory
> Xen:
setup ISA identity maps
> about to get started...
> Initializing cgroup subsys cpuset
> Initializing cgroup subsys cpu
> Linux version 2.6.32.13 (gcc version 4.1.2 20080704 (Red
Hat
> 4.1.2-44)) #2 SMP Thu May 20 17:22:39 PDT 2010
> Command line: ro root=/dev/sda2 console=hvc0 earlyprintk=xen nomodeset debug
log
> level=10
> KERNEL supported cpus:
> Intel GenuineIntel
> AMD
AuthenticAMD
> Centaur CentaurHauls
> released 0 pages of unused memory
> BIOS-provided physical RAM map:
> Xen: 0000000000000000 - 0000000000095800
(usable)
> Xen: 0000000000095800 - 0000000000100000 (reserved)
> Xen: 0000000000100000 - 00000000b5164000
(usable)
> Xen: 00000000bf7a5800 - 00000000c0000000 (reserved)
> Xen: 00000000f0000000 - 00000000f8000000
(reserved)
> Xen: 00000000fec00000 - 00000000fed40000 (reserved)
> Xen: 00000000fed45000 - 0000000100000000
(reserved)
> bootconsole [xenboot0] enabled
> DMI 2.6 present.
> last_pfn = 0xb5164 max_arch_pfn = 0x400000000
> x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
> initial memory mapped : 0 - 20000000
> init_memory_mapping:
0000000000000000-00000000b5164000
> 0000000000 - 00b5164000 page 4k
> kernel direct mapping tables up to b5164000 @
100000-6ad000
> RAMDISK: 02768000 - 02c1ec00
> ACPI: RSDP 00000000000e9010 00024 (v02 HP
> ACPI: XSDT 00000000bf7b88e8 0006C (v01 HPQOEM SLIC-WKS 20091208
00000000)
> ACPI: FACP 00000000bf7b8a88 000F4 (v03 HPQOEM TYLSBURG 00000001
00000000)
> ACPI: DSDT 00000000bf7b92d7 0A73D (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
> ACPI: FACS 00000000bf7b8800 00040
> ACPI: APIC 00000000bf7b8b7c 00114 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: ASF! 00000000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: TCPA
00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)
> ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: 00000000bf7b8f0f 001B8 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: SSDT 00000000bf7c4ee6 011FC (v01 INTEL PPM RCM 80000001 INTL 20061109)
> ACPI: Local APIC address 0xfee00000
> No NUMA configuration found
> Faking a node at 0000000000000000-00000000b5164000
> Bootmem setup node 0 0000000000000000-00000000b5164000
> NODE_DATA [0000000000008000 - 000000000001ffff]
> bootmap [0000000000020000 - 0000000000036a2f] pages 17
> (8 early reservations) ==> bootmem [0000000000 -
00b5164000]
> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
> #1 [00031c9000 - 00031e6000] XEN PAGETABLES ==> [00031c9000 - 00031e6000]
> #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
> #3 [0001000000 - 0002747680] TEXT DATA BSS ==> [0001000000 - 0002747680]
> #4 [0002768000 - 0002c1ec00] RAMDISK ==> [0002768000 - 0002c1ec00]
> #5 [0002c1f000 - 00031c9000] XEN START INFO ==> [0002c1f000 - 00031c9000]
> #6 [0002748000 - 0002748120] BRK ==> [0002748000 - 0002748120]
> #7 [0000100000 - 000068d000] PGTABLE ==>
[0000100000
>
>
> Any thoughts ?
It looks as if your serial card is eating up characters. You could lower
the baud-rate down to say 9600?
[-- Attachment #1.2: Type: text/html, Size: 130044 bytes --]
[-- Attachment #2: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 15+ messages in thread* Re: boot Xen 4.0
2010-06-10 16:02 ccmail111
@ 2010-06-15 21:26 ` Konrad Rzeszutek Wilk
0 siblings, 0 replies; 15+ messages in thread
From: Konrad Rzeszutek Wilk @ 2010-06-15 21:26 UTC (permalink / raw)
To: ccmail111; +Cc: deshantm, yingbin wang, xen-devel
> Linux version 2.6.32.13 (root@xyz) (gcc version 4.1.2 20080704 (Red Hat0095800 (usable)
> (XEN) 00000
> 4.1.2-44)) #2 SMP Thu May 20 17:22:39 PDT 2010
>
> Xen: 0000000000000000 - 0000000000095800 (usable)
> (XEN) 00000000fed45000 - 0000000100000000 (r
> Xen: 0000000000095800 - 0000000000100000 (reserved)
> (XEN) System RAM: 3033MB (3106320kB)
> Xen: 0000000000100000 - 00000000b5164000 (usable)9010, 0024 (r2 HPQOEM)
> Xen: 00000000bf7a5800 - 00000000c0000000 (reserved)PQOEM SLIC-WKS 20091208 0)
> Xen: 00000000f0000000 - 00000000f8000000 (reserved)
>
> last_pfn = 0xb5164 max_arch_pfn = 0x400000000
> (XEN) ACPI: APIC BF7B8B7C, 01
> x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
> (XE
> initial memory mapped : 0 - 20000000OEM TYLSBURG 1 0)
> init_memory_mapping: 0000000000000000-00000000b5164000
> (XEN) ACPI: MCFG BF7B8CF3, 003C
> 0000000000 - 00b5164000 page 4k 0)
> kernel direct mapping tables up to b5164000 @ 100000-6ad000ACPI: TCPA BF7B8D2F, 0032 (r1 HPQOEM TYLSBURG 1
> RAMDISK: 02768000 - 02c1ec00
> ACPI: FACS 00000000bf7b8800 00040
> ACPI: APIC 00000000bf7b8b7c 00114 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: ASF! 00000000bf7b8c90 00063 (v32 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: MCFG 00000000bf7b8cf3 0003C (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: TCPA 00000000bf7b8d2f 00032 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: SLIC 00000000bf7b8d61 00176 (v01 HPQOEM SLIC-WKS 00000001 00000000)
> ACPI: HPET 00000000bf7b8ed7 00038 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: 00000000bf7b8f0f 001B8 (v01 HPQOEM TYLSBURG 00000001 00000000)
> ACPI: SSDT 00000000bf7c4ee6 011FC (v01 INTEL PPM RCM 80000001 INTL 20061109)
> ACPI: Local APIC address 0xfee00000
> No NUMA configuration found
> Faking a node at 0000000000000000-00000000b5164000
> Bootmem setup node 0 0000000000000000-00000000b5164000
> NODE_DATA [0000000000008000 - 000000000001ffff]
> bootmap [0000000000020000 - 0000000000036a2f] pages 17
> (8 early reservations) ==> bootmem [0000000000 - 00b5164000]
> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
> #1 [00031c9000 - 00031e6000] XEN PAGETABLES ==> [00031c9000 - 00031e6000]
> #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
> #3 [0001000000 - 0002747680] TEXT DATA BSS ==> [0001000000 - 0002747680]
> #4 [0002768000 - 0002c1ec00] RAMDISK ==> [0002768000 - 0002c1ec00]
> #5 [0002c1f000 - 00031c9000] XEN START INFO ==> [0002c1f000 - 00031c9000]
> #6 [0002748000 - 0002748120] BRK ==> [0002748000 - 0002748120]
> #7 [0000100000 - 000068d000] PGTABLE ==> [0000100000
>
>
This points to the E820 being wacked, but I can't see how that is
possible considering Xen boots. Try forcing your domain to a smaller
memory amount. Use 'dom0_mem=max:1G' in your Xen command line.
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: boot Xen 4.0
@ 2010-05-18 19:08 ccmail111
2010-05-18 19:11 ` Pasi Kärkkäinen
0 siblings, 1 reply; 15+ messages in thread
From: ccmail111 @ 2010-05-18 19:08 UTC (permalink / raw)
To: yingbin wang; +Cc: deshantm, xen-devel
[-- Attachment #1.1: Type: text/plain, Size: 6685 bytes --]
Thanks for tip below.
1) I tried rebuild kernel with option below. I now build kernel with:
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
But see problem below during boot up as below..
grub.conf:
title Xen 4.0 debug XenLinux 2.6
root (hd0,0)
kernel /xen-4.0.0.gz console=com1, com1=115200,8n1 noreboot loglvl=all vga=text-80x50,keep iommu=off apic=debug guest_loglvl=all
module /vmlinuz-2.6.31.13 ro root=/dev/ram0 console=hvc0 earlyprintk=xen nomodeset initcall_debug debug loglevel=10
module
/initrd.img-2.6.31.13
2) Is there a
reference (working) ramdisk/initrd for Xen4.0 with busybox or such ? I created ramdisk as:
# mkinitrd -v -f --builtin=ehci-hcd --builtin=ohci-hcd --builtin=uhci-hcd --builtin=ahci --builtin=aacraid --builtin=aacraid --builtin=sd_mod --builtin=scsi_mod /boot/initrd.img-2.6.31.13 2.6.31.13
Using this (since there is no busybox or such):
Trying to resume from /dev/sdb2
Unable to access resume device (/dev/sdb2)
Creating root device.
usb 5-1: new full speed USB device using uhci_hcd and address 2
Mounting root filesystem.
VFS: Can't find ext3 filesystem on dev ram0.
mount: error mounting /dev/root on /sysroot as ext3: Invalid argument
Setting up other filesystems.
Setting up new root fs
setuproot: moving /dev failed: No such file or directory
no fstab.sys, mounting internal defaults
setuproot: error mounting /proc: No such file or directory
setuproot: error mounting /sys: No such file or directory
Switching to new root and running init.
unmounting old /dev
unmounting old /proc
unmounting old /sys
switchroot: mount failed: No such file or directory
Kernel panic - not syncing: Attempted to kill init!
Pid: 1, comm: init Not tainted 2.6.31.13 #8
Call Trace:
[<ffffffff8106bbeb>] panic+0xb7/0x172
[<ffffffff8106fe04>] ? do_exit+0x37c/0x6de
[<ffffffff8100fa6f>] ? xen_restore_fl_direct_end+0x0/0x1
[<ffffffff810a1c6b>] ? lock_release+0x197/0x1b8
[<ffffffff8109ef6e>] ? trace_hardirqs_on+0x20/0x36
[<ffffffff815436be>] ? _write_unlock_irq+0x46/0x61
[<ffffffff8106fb15>] do_exit+0x8d/0x6de
[<ffffffff8107021e>] sys_exit_group+0x0/0x42
[<ffffffff8154265c>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff81070248>] sys_exit_group+0x2a/0x42
[<ffffffff81015332>] system_call_fastpath+0x16/0x1b
Any suggestions ?
Thanks !
CM
--- On Sat, 5/15/10, yingbin wang <yingbin.wangyb@gmail.com> wrote:
From: yingbin wang
<yingbin.wangyb@gmail.com>
Subject: Re: [Xen-devel] boot Xen 4.0
To: "ccmail111" <ccmail111@yahoo.com>
Cc: "Pasi Kärkkäinen" <pasik@iki.fi>, deshantm@gmail.com, xen-devel@lists.xensource.com
Date: Saturday, May 15, 2010, 12:34 PM
I met similar problems and solved it.
if your grub.conf is OK, you can try to edit a option of your .config.
CONFIG_SYSFS_DEPRECATED_V2=y
2010/5/14 ccmail111 <ccmail111@yahoo.com>
>
> Thanks
Pasi/Todd,
>
> I did:
> # mkinitrd -v -f --builtin=ehci-hcd --builtin=ohci-hcd --builtin=uhci-hcd --builtin=ahci --builtin=aacraid --builtin=aacraid --builtin=sd_mod --builtin=scsi_mod /boot/initrd.img-2.6.31.13 2.6.31.13
>
>
> Now
> I see during boot: kernel panic:
>
> Mounting root filesystem.
> mount: could not find filesystem '/dev/root'
> setting up other filesystems
> setting up new root fs
> setuproot: moving /dev failed No such file or directory
> setuproot: error mounting /proc: No such file or directory
> setuproot: error mounting /sys: No such file or directory
> switchroot: mount failed: No such file or directory
> kernel panic - not syncing : Attempted to kill init !
>
>
>
>
> --- On Thu, 5/13/10, Pasi Kärkkäinen <pasik@iki.fi> wrote:
>
> From: Pasi Kärkkäinen
<pasik@iki.fi>
> Subject: Re: [Xen-devel] initrd Xen 4.0
> To: "ccmail111" <ccmail111@yahoo.com>
> Cc: deshantm@gmail.com, xen-devel@lists.xensource.com
> Date: Thursday, May 13, 2010, 4:27 PM
>
> On Thu, May 13, 2010 at 01:08:36PM -0700, ccmail111 wrote:
> > The #5 of README is not clear in details.
> > which directory to run depmod and mkinitrd from ?
> >
>
> It doesn't matter.
>
>
> I see:
> >
> > # depmod xen-4.0.0
> > WARNING: Couldn't find symtab and strtab in module xen-4.0.0
> >
>
> Wrong. You need to run depmod for the *kernel*, not for xen.
>
> So like this:
> depmod -a 2.6.32.12
>
> Or whatever is your kernel version.
>
> -- Pasi
>
> > # ls -l
> > total 1356
> > -rw-r--r-- 1 root root 1380620 May 13 13:05 xen-4.0.0
> >
> > Any suggestions ?
> >
> > --- On Wed, 5/12/10, Todd Deshane <deshantm@gmail.com> wrote:
> >
> > From: Todd Deshane <deshantm@gmail.com>
> > Subject: Re: [Xen-devel] initrd Xen 4.0
> > To:
"ccmail111" <ccmail111@yahoo.com>
> > Cc: xen-devel@lists.xensource.com
> > Date: Wednesday, May 12, 2010, 9:46 PM
> >
> > Hi,
> >
> > See inline.
> >
> > On Wed, May 12, 2010 at 12:25 PM, ccmail111 <[1]ccmail111@yahoo.com>
> > wrote:
> > >
> >
> Hi,
> > >
> > > I downloaded Xen 4.0 and did:
> > > make install
> > > I donot see initrd (ramdisk) being created at all.
> > >
> > > Any suggestions ?
> > >
> >
> > Step 5 of the README
> > Depending on your config, you may need to use 'mkinitrd' to create
> > an initial ram disk, just like a native system e.g.
> > # depmod 2.6.18-xen
> > # mkinitrd -v -f --with=aacraid --with=sd_mod --with=scsi_mod
> > initrd-2.6.18-xen.img 2.6.18-xen
> >
Other systems may requires the use of 'mkinitramfs' to create the
> > ram disk.
> > # depmod 2.6.18-xen
> > # mkinitramfs -o initrd-2.6.18-xen.img 2.6.18-xen
> >
> > You may need to change the kernel version based on what you built.
> > Also some distros use different commands to build initrd files.
> >
> > I actually forgot about this step for a second too.
> >
> > Thanks,
> > Todd
> >
> > --
> > Todd Deshane
> > [2]http://todddeshane.net
> >
[3]http://runningxen.com
> >
> > References
> >
> > Visible links
> > 1. file:///mc/compose?to=ccmail111@yahoo.com
> > 2. http://todddeshane.net/
> > 3. http://runningxen.com/
>
> > _______________________________________________
> > Xen-devel mailing list
> > Xen-devel@lists.xensource.com
> > http://lists.xensource.com/xen-devel
>
>
>
>
_______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
>
[-- Attachment #1.2: Type: text/html, Size: 10167 bytes --]
[-- Attachment #2: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 15+ messages in thread* Re: boot Xen 4.0
2010-05-18 19:08 ccmail111
@ 2010-05-18 19:11 ` Pasi Kärkkäinen
2010-05-18 21:46 ` ccmail111
0 siblings, 1 reply; 15+ messages in thread
From: Pasi Kärkkäinen @ 2010-05-18 19:11 UTC (permalink / raw)
To: ccmail111; +Cc: deshantm, yingbin wang, xen-devel
On Tue, May 18, 2010 at 12:08:36PM -0700, ccmail111 wrote:
> Thanks for tip below.
>
> 1) I tried rebuild kernel with option below. I now build kernel with:
>
> CONFIG_SYSFS_DEPRECATED=y
> CONFIG_SYSFS_DEPRECATED_V2=y
>
> But see problem below during boot up as below..
>
> grub.conf:
>
> title Xen 4.0 debug XenLinux 2.6
> root (hd0,0)
> kernel /xen-4.0.0.gz console=com1, com1=115200,8n1 noreboot
> loglvl=all vga=text-80x50,keep iommu=off apic=debug guest_loglvl=all
> module /vmlinuz-2.6.31.13 ro root=/dev/ram0 console=hvc0
> earlyprintk=xen nomodeset initcall_debug debug loglevel=10
your root= parameter is wrong.
You need to have the actual root partition path there.
-- Pasi
> module /initrd.img-2.6.31.13
>
> 2) Is there a reference (working) ramdisk/initrd for Xen4.0 with busybox
> or such ? I created ramdisk as:
>
> # mkinitrd -v -f --builtin=ehci-hcd --builtin=ohci-hcd --builtin=uhci-hcd
> --builtin=ahci --builtin=aacraid --builtin=aacraid --builtin=sd_mod
> --builtin=scsi_mod /boot/initrd.img-2.6.31.13 2.6.31.13
>
> Using this (since there is no busybox or such):
>
> Trying to resume from /dev/sdb2
> Unable to access resume device (/dev/sdb2)
> Creating root device.
> usb 5-1: new full speed USB device using uhci_hcd and address 2
> Mounting root filesystem.
> VFS: Can't find ext3 filesystem on dev ram0.
> mount: error mounting /dev/root on /sysroot as ext3: Invalid argument
> Setting up other filesystems.
> Setting up new root fs
> setuproot: moving /dev failed: No such file or directory
> no fstab.sys, mounting internal defaults
> setuproot: error mounting /proc: No such file or directory
> setuproot: error mounting /sys: No such file or directory
> Switching to new root and running init.
> unmounting old /dev
> unmounting old /proc
> unmounting old /sys
> switchroot: mount failed: No such file or directory
> Kernel panic - not syncing: Attempted to kill init!
> Pid: 1, comm: init Not tainted 2.6.31.13 #8
> Call Trace:
> [<ffffffff8106bbeb>] panic+0xb7/0x172
> [<ffffffff8106fe04>] ? do_exit+0x37c/0x6de
> [<ffffffff8100fa6f>] ? xen_restore_fl_direct_end+0x0/0x1
> [<ffffffff810a1c6b>] ? lock_release+0x197/0x1b8
> [<ffffffff8109ef6e>] ? trace_hardirqs_on+0x20/0x36
> [<ffffffff815436be>] ? _write_unlock_irq+0x46/0x61
> [<ffffffff8106fb15>] do_exit+0x8d/0x6de
> [<ffffffff8107021e>] sys_exit_group+0x0/0x42
> [<ffffffff8154265c>] ? trace_hardirqs_on_thunk+0x3a/0x3f
> [<ffffffff81070248>] sys_exit_group+0x2a/0x42
> [<ffffffff81015332>] system_call_fastpath+0x16/0x1b
>
> Any suggestions ?
>
> Thanks !
>
> CM
>
> --- On Sat, 5/15/10, yingbin wang <yingbin.wangyb@gmail.com> wrote:
>
> From: yingbin wang <yingbin.wangyb@gmail.com>
> Subject: Re: [Xen-devel] boot Xen 4.0
> To: "ccmail111" <ccmail111@yahoo.com>
> Cc: "Pasi Kärkkäinen" <pasik@iki.fi>, deshantm@gmail.com,
> xen-devel@lists.xensource.com
> Date: Saturday, May 15, 2010, 12:34 PM
>
> I met similar problems and solved it.
>
> if your grub.conf is OK, you can try to edit a option of your .config.
> CONFIG_SYSFS_DEPRECATED_V2=y
>
> 2010/5/14 ccmail111 <ccmail111@yahoo.com>
> >
> > Thanks Pasi/Todd,
> >
> > I did:
> > # mkinitrd -v -f --builtin=ehci-hcd --builtin=ohci-hcd
> --builtin=uhci-hcd --builtin=ahci --builtin=aacraid --builtin=aacraid
> --builtin=sd_mod --builtin=scsi_mod /boot/initrd.img-2.6.31.13 2.6.31.13
> >
> >
> > Now
> > I see during boot: kernel panic:
> >
> > Mounting root filesystem.
> > mount: could not find filesystem '/dev/root'
> > setting up other filesystems
> > setting up new root fs
> > setuproot: moving /dev failed No such file or directory
> > setuproot: error mounting /proc: No such file or directory
> > setuproot: error mounting /sys: No such file or directory
> > switchroot: mount failed: No such file or directory
> > kernel panic - not syncing : Attempted to kill init !
> >
> >
> >
> >
> > --- On Thu, 5/13/10, Pasi Kärkkäinen <pasik@iki.fi> wrote:
> >
> > From: Pasi Kärkkäinen <pasik@iki.fi>
> > Subject: Re: [Xen-devel] initrd Xen 4.0
> > To: "ccmail111" <ccmail111@yahoo.com>
> > Cc: deshantm@gmail.com, xen-devel@lists.xensource.com
> > Date: Thursday, May 13, 2010, 4:27 PM
> >
> > On Thu, May 13, 2010 at 01:08:36PM -0700, ccmail111 wrote:
> > > The #5 of README is not clear in details.
> > > which directory to run depmod and mkinitrd from ?
> > >
> >
> > It doesn't matter.
> >
> > > I see:
> > >
> > > # depmod xen-4.0.0
> > > WARNING: Couldn't find symtab and strtab in module xen-4.0.0
> > >
> >
> > Wrong. You need to run depmod for the *kernel*, not for xen.
> >
> > So like this:
> > depmod -a 2.6.32.12
> >
> > Or whatever is your kernel version.
> >
> > -- Pasi
> >
> > > # ls -l
> > > total 1356
> > > -rw-r--r-- 1 root root 1380620 May 13 13:05 xen-4.0.0
> > >
> > > Any suggestions ?
> > >
> > > --- On Wed, 5/12/10, Todd Deshane <deshantm@gmail.com> wrote:
> > >
> > > From: Todd Deshane <deshantm@gmail.com>
> > > Subject: Re: [Xen-devel] initrd Xen 4.0
> > > To: "ccmail111" <ccmail111@yahoo.com>
> > > Cc: xen-devel@lists.xensource.com
> > > Date: Wednesday, May 12, 2010, 9:46 PM
> > >
> > > Hi,
> > >
> > > See inline.
> > >
> > > On Wed, May 12, 2010 at 12:25 PM, ccmail111
> <[1]ccmail111@yahoo.com>
> > > wrote:
> > > >
> > > > Hi,
> > > >
> > > > I downloaded Xen 4.0 and did:
> > > > make install
> > > > I donot see initrd (ramdisk) being created at all.
> > > >
> > > > Any suggestions ?
> > > >
> > >
> > > Step 5 of the README
> > > Depending on your config, you may need to use 'mkinitrd' to
> create
> > > an initial ram disk, just like a native system e.g.
> > > # depmod 2.6.18-xen
> > > # mkinitrd -v -f --with=aacraid --with=sd_mod
> --with=scsi_mod
> > > initrd-2.6.18-xen.img 2.6.18-xen
> > > Other systems may requires the use of 'mkinitramfs' to
> create the
> > > ram disk.
> > > # depmod 2.6.18-xen
> > > # mkinitramfs -o initrd-2.6.18-xen.img 2.6.18-xen
> > >
> > > You may need to change the kernel version based on what you
> built.
> > > Also some distros use different commands to build initrd files.
> > >
> > > I actually forgot about this step for a second too.
> > >
> > > Thanks,
> > > Todd
> > >
> > > --
> > > Todd Deshane
> > > [2][1]http://todddeshane.net
> > > [3][2]http://runningxen.com
> > >
> > > References
> > >
> > > Visible links
> > > 1. file:///mc/compose?to=ccmail111@yahoo.com
> > > 2. [3]http://todddeshane.net/
> > > 3. [4]http://runningxen.com/
> >
> > > _______________________________________________
> > > Xen-devel mailing list
> > > Xen-devel@lists.xensource.com
> > > [5]http://lists.xensource.com/xen-devel
> >
> >
> >
> > _______________________________________________
> > Xen-devel mailing list
> > Xen-devel@lists.xensource.com
> > [6]http://lists.xensource.com/xen-devel
> >
>
> References
>
> Visible links
> 1. http://todddeshane.net/
> 2. http://runningxen.com/
> 3. http://todddeshane.net/
> 4. http://runningxen.com/
> 5. http://lists.xensource.com/xen-devel
> 6. http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: boot Xen 4.0
2010-05-18 19:11 ` Pasi Kärkkäinen
@ 2010-05-18 21:46 ` ccmail111
2010-05-26 17:44 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 15+ messages in thread
From: ccmail111 @ 2010-05-18 21:46 UTC (permalink / raw)
To: Pasi Kärkkäinen; +Cc: deshantm, yingbin wang, xen-devel
[-- Attachment #1.1: Type: text/plain, Size: 9784 bytes --]
Hi Pasi,
I'm sorry for typo below grub.conf is:
title Xen 4.0 debug XenLinux 2.6
root (hd0,0)
kernel /xen-4.0.0.gz console=com1, com1=115200,8n1 noreboot loglvl=all vga=text-80x50,keep iommu=off apic=debug guest_loglvl=all
module /vmlinuz-2.6.31.13 ro root=/dev/sda3 console=hvc0 earlyprintk=xen nomodeset initcall_debug debug loglevel=10
module /initrd.img-2.6.31.13
on another PC during boot up I see another problem - it is stuck at error:
ACPI Error (dsField-0140): [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS.
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSCI] (Node ffff8800b4c12500), AE_ALREADY_EXISTS
aer 0000:00:01.0: pcie02: AER service couldn't init device: _OSC failed
<...clip..errors...>
(XEN) irq.c: 1182:d0 Cannot bind IRQ 0 to guest. Will not share with others.
<..clip..>
[drm] Initialized drm 1.1.0 20060810
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
Any thoughts ?
Thanks !
CM
--- On Tue, 5/18/10, Pasi Kärkkäinen <pasik@iki.fi> wrote:
From: Pasi Kärkkäinen <pasik@iki.fi>
Subject: Re: [Xen-devel] boot Xen 4.0
To: "ccmail111" <ccmail111@yahoo.com>
Cc: "yingbin wang" <yingbin.wangyb@gmail.com>, deshantm@gmail.com, xen-devel@lists.xensource.com
Date: Tuesday, May 18, 2010, 3:11 PM
On Tue, May 18, 2010 at 12:08:36PM -0700, ccmail111 wrote:
> Thanks for tip below.
>
> 1) I tried rebuild kernel with option below. I now build kernel with:
>
> CONFIG_SYSFS_DEPRECATED=y
> CONFIG_SYSFS_DEPRECATED_V2=y
>
> But see problem below during boot up as below..
>
> grub.conf:
>
> title Xen 4.0 debug XenLinux 2.6
> root (hd0,0)
> kernel /xen-4.0.0.gz console=com1, com1=115200,8n1 noreboot
> loglvl=all vga=text-80x50,keep iommu=off apic=debug guest_loglvl=all
> module /vmlinuz-2.6.31.13 ro root=/dev/ram0 console=hvc0
> earlyprintk=xen nomodeset initcall_debug debug loglevel=10
your root= parameter is wrong.
You need to have the actual root partition path there.
-- Pasi
> module /initrd.img-2.6.31.13
>
> 2) Is there a reference (working) ramdisk/initrd for Xen4.0 with busybox
> or such ? I created ramdisk as:
>
> # mkinitrd -v -f --builtin=ehci-hcd --builtin=ohci-hcd --builtin=uhci-hcd
> --builtin=ahci --builtin=aacraid --builtin=aacraid --builtin=sd_mod
> --builtin=scsi_mod /boot/initrd.img-2.6.31.13 2.6.31.13
>
> Using this (since there is no busybox or such):
>
> Trying to resume from /dev/sdb2
> Unable to access resume device (/dev/sdb2)
> Creating root device.
> usb 5-1: new full speed USB device using uhci_hcd and address 2
> Mounting root filesystem.
> VFS: Can't find ext3 filesystem on dev ram0.
> mount: error mounting /dev/root on /sysroot as ext3: Invalid argument
> Setting up other filesystems.
> Setting up new root fs
> setuproot: moving /dev failed: No such file or directory
> no fstab.sys, mounting internal defaults
> setuproot: error mounting /proc: No such file or directory
> setuproot: error mounting /sys: No such file or directory
> Switching to new root and running init.
> unmounting old /dev
> unmounting old /proc
> unmounting old /sys
> switchroot: mount failed: No such file or directory
> Kernel panic - not syncing: Attempted to kill init!
> Pid: 1, comm: init Not tainted 2.6.31.13 #8
> Call Trace:
> [<ffffffff8106bbeb>] panic+0xb7/0x172
> [<ffffffff8106fe04>] ? do_exit+0x37c/0x6de
> [<ffffffff8100fa6f>] ? xen_restore_fl_direct_end+0x0/0x1
> [<ffffffff810a1c6b>] ? lock_release+0x197/0x1b8
> [<ffffffff8109ef6e>] ? trace_hardirqs_on+0x20/0x36
> [<ffffffff815436be>] ? _write_unlock_irq+0x46/0x61
> [<ffffffff8106fb15>] do_exit+0x8d/0x6de
> [<ffffffff8107021e>] sys_exit_group+0x0/0x42
> [<ffffffff8154265c>] ? trace_hardirqs_on_thunk+0x3a/0x3f
> [<ffffffff81070248>] sys_exit_group+0x2a/0x42
> [<ffffffff81015332>] system_call_fastpath+0x16/0x1b
>
> Any suggestions ?
>
> Thanks !
>
> CM
>
> --- On Sat, 5/15/10, yingbin wang <yingbin.wangyb@gmail.com> wrote:
>
> From: yingbin wang <yingbin.wangyb@gmail.com>
> Subject: Re: [Xen-devel] boot Xen 4.0
> To: "ccmail111" <ccmail111@yahoo.com>
> Cc: "Pasi Kärkkäinen" <pasik@iki.fi>, deshantm@gmail.com,
> xen-devel@lists.xensource.com
> Date: Saturday, May 15, 2010, 12:34 PM
>
> I met similar problems and solved it.
>
> if your grub.conf is OK, you can try to edit a option of your .config.
> CONFIG_SYSFS_DEPRECATED_V2=y
>
> 2010/5/14 ccmail111 <ccmail111@yahoo.com>
> >
> > Thanks Pasi/Todd,
> >
> > I did:
> > # mkinitrd -v -f --builtin=ehci-hcd --builtin=ohci-hcd
> --builtin=uhci-hcd --builtin=ahci --builtin=aacraid --builtin=aacraid
> --builtin=sd_mod --builtin=scsi_mod /boot/initrd.img-2.6.31.13 2.6.31.13
> >
> >
> > Now
> > I see during boot: kernel panic:
> >
> > Mounting root filesystem.
> > mount: could not find filesystem '/dev/root'
> > setting up other filesystems
> > setting up new root fs
> > setuproot: moving /dev failed No such file or directory
> > setuproot: error mounting /proc: No such file or directory
> > setuproot: error mounting /sys: No such file or directory
> > switchroot: mount failed: No such file or directory
> > kernel panic - not syncing : Attempted to kill init !
> >
> >
> >
> >
> > --- On Thu, 5/13/10, Pasi Kärkkäinen <pasik@iki.fi> wrote:
> >
> > From: Pasi Kärkkäinen <pasik@iki.fi>
> > Subject: Re: [Xen-devel] initrd Xen 4.0
> > To: "ccmail111" <ccmail111@yahoo.com>
> > Cc: deshantm@gmail.com, xen-devel@lists.xensource.com
> > Date: Thursday, May 13, 2010, 4:27 PM
> >
> > On Thu, May 13, 2010 at 01:08:36PM -0700, ccmail111 wrote:
> > > The #5 of README is not clear in details.
> > > which directory to run depmod and mkinitrd from ?
> > >
> >
> > It doesn't matter.
> >
> > > I see:
> > >
> > > # depmod xen-4.0.0
> > > WARNING: Couldn't find symtab and strtab in module xen-4.0.0
> > >
> >
> > Wrong. You need to run depmod for the *kernel*, not for xen.
> >
> > So like this:
> > depmod -a 2.6.32.12
> >
> > Or whatever is your kernel version.
> >
> > -- Pasi
> >
> > > # ls -l
> > > total 1356
> > > -rw-r--r-- 1 root root 1380620 May 13 13:05 xen-4.0.0
> > >
> > > Any suggestions ?
> > >
> > > --- On Wed, 5/12/10, Todd Deshane <deshantm@gmail.com> wrote:
> > >
> > > From: Todd Deshane <deshantm@gmail.com>
> > > Subject: Re: [Xen-devel] initrd Xen 4.0
> > > To: "ccmail111" <ccmail111@yahoo.com>
> > > Cc: xen-devel@lists.xensource.com
> > > Date: Wednesday, May 12, 2010, 9:46 PM
> > >
> > > Hi,
> > >
> > > See inline.
> > >
> > > On Wed, May 12, 2010 at 12:25 PM, ccmail111
> <[1]ccmail111@yahoo.com>
> > > wrote:
> > > >
> > > > Hi,
> > > >
> > > > I downloaded Xen 4.0 and did:
> > > > make install
> > > > I donot see initrd (ramdisk) being created at all.
> > > >
> > > > Any suggestions ?
> > > >
> > >
> > > Step 5 of the README
> > > Depending on your config, you may need to use 'mkinitrd' to
> create
> > > an initial ram disk, just like a native system e.g.
> > > # depmod 2.6.18-xen
> > > # mkinitrd -v -f --with=aacraid --with=sd_mod
> --with=scsi_mod
> > > initrd-2.6.18-xen.img 2.6.18-xen
> > > Other systems may requires the use of 'mkinitramfs' to
> create the
> > > ram disk.
> > > # depmod 2.6.18-xen
> > > # mkinitramfs -o initrd-2.6.18-xen.img 2.6.18-xen
> > >
> > > You may need to change the kernel version based on what you
> built.
> > > Also some distros use different commands to build initrd files.
> > >
> > > I actually forgot about this step for a second too.
> > >
> > > Thanks,
> > > Todd
> > >
> > > --
> > > Todd Deshane
> > > [2][1]http://todddeshane.net
> > > [3][2]http://runningxen.com
> > >
> > > References
> > >
> > > Visible links
> > > 1. file:///mc/compose?to=ccmail111@yahoo.com
> > > 2. [3]http://todddeshane.net/
> > > 3. [4]http://runningxen.com/
> >
> > > _______________________________________________
> > > Xen-devel mailing list
> > > Xen-devel@lists.xensource.com
> > > [5]http://lists.xensource.com/xen-devel
> >
> >
> >
> > _______________________________________________
> > Xen-devel mailing list
> > Xen-devel@lists.xensource.com
> > [6]http://lists.xensource.com/xen-devel
> >
>
> References
>
> Visible links
> 1. http://todddeshane.net/
> 2. http://runningxen.com/
> 3. http://todddeshane.net/
> 4. http://runningxen.com/
> 5. http://lists.xensource.com/xen-devel
> 6. http://lists.xensource.com/xen-devel
[-- Attachment #1.2: Type: text/html, Size: 18675 bytes --]
[-- Attachment #2: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 15+ messages in thread* Re: boot Xen 4.0
2010-05-18 21:46 ` ccmail111
@ 2010-05-26 17:44 ` Konrad Rzeszutek Wilk
0 siblings, 0 replies; 15+ messages in thread
From: Konrad Rzeszutek Wilk @ 2010-05-26 17:44 UTC (permalink / raw)
To: ccmail111; +Cc: deshantm, yingbin wang, xen-devel
On Tue, May 18, 2010 at 02:46:10PM -0700, ccmail111 wrote:
> Hi Pasi,
>
> I'm sorry for typo below grub.conf is:
>
> title Xen 4.0 debug XenLinux 2.6
> root (hd0,0)
> kernel /xen-4.0.0.gz console=com1, com1=115200,8n1 noreboot loglvl=all vga=text-80x50,keep iommu=off apic=debug guest_loglvl=all
> module /vmlinuz-2.6.31.13 ro root=/dev/sda3 console=hvc0 earlyprintk=xen nomodeset initcall_debug debug loglevel=10
> module /initrd.img-2.6.31.13
>
>
> on another PC during boot up I see another problem - it is stuck at error:
>
> ACPI Error (dsField-0140): [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS.
> ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSCI] (Node ffff8800b4c12500), AE_ALREADY_EXISTS
> aer 0000:00:01.0: pcie02: AER service couldn't init device: _OSC failed
>
> <...clip..errors...>
> (XEN) irq.c: 1182:d0 Cannot bind IRQ 0 to guest. Will not share with others.
> <..clip..>
> [drm] Initialized drm 1.1.0 20060810
> Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
Can you attach the full serial log?
What is the distro? If it is Fedora Core 12 or later you need to use
dracut to create an initramfs instead of the mkinitrd.
Does your VGA screen show anything?
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: boot Xen 4.0
@ 2010-05-14 1:42 ccmail111
2010-05-14 5:55 ` Pasi Kärkkäinen
2010-05-15 16:34 ` yingbin wang
0 siblings, 2 replies; 15+ messages in thread
From: ccmail111 @ 2010-05-14 1:42 UTC (permalink / raw)
To: Pasi Kärkkäinen; +Cc: deshantm, xen-devel
[-- Attachment #1.1: Type: text/plain, Size: 3408 bytes --]
Thanks Pasi/Todd,
I did:
# mkinitrd -v -f --builtin=ehci-hcd --builtin=ohci-hcd --builtin=uhci-hcd --builtin=ahci --builtin=aacraid --builtin=aacraid --builtin=sd_mod --builtin=scsi_mod /boot/initrd.img-2.6.31.13 2.6.31.13
Now
I see during boot: kernel panic:
Mounting root filesystem.
mount: could not find filesystem '/dev/root'
setting up other filesystems
setting up new root fs
setuproot: moving /dev failed No such file or directory
setuproot: error mounting /proc: No such file or directory
setuproot: error mounting /sys: No such file or directory
switchroot: mount failed: No such file or directory
kernel panic - not syncing : Attempted to kill init !
--- On Thu, 5/13/10, Pasi Kärkkäinen <pasik@iki.fi> wrote:
From: Pasi Kärkkäinen <pasik@iki.fi>
Subject: Re: [Xen-devel] initrd Xen 4.0
To: "ccmail111" <ccmail111@yahoo.com>
Cc: deshantm@gmail.com, xen-devel@lists.xensource.com
Date: Thursday, May 13, 2010, 4:27 PM
On Thu, May 13, 2010 at 01:08:36PM -0700, ccmail111
wrote:
> The #5 of README is not clear in details.
> which directory to run depmod and mkinitrd from ?
>
It doesn't matter.
> I see:
>
> # depmod xen-4.0.0
> WARNING: Couldn't find symtab and strtab in module xen-4.0.0
>
Wrong. You need to run depmod for the *kernel*, not for xen.
So like this:
depmod -a 2.6.32.12
Or whatever is your kernel version.
-- Pasi
> # ls -l
> total 1356
> -rw-r--r-- 1 root root 1380620 May 13 13:05 xen-4.0.0
>
> Any suggestions ?
>
> --- On Wed, 5/12/10, Todd Deshane <deshantm@gmail.com> wrote:
>
> From: Todd Deshane <deshantm@gmail.com>
> Subject: Re: [Xen-devel] initrd Xen 4.0
> To: "ccmail111" <ccmail111@yahoo.com>
> Cc: xen-devel@lists.xensource.com
> Date: Wednesday, May 12, 2010, 9:46 PM
>
> Hi,
>
> See inline.
>
> On Wed, May 12, 2010 at 12:25 PM, ccmail111 <[1]ccmail111@yahoo.com>
> wrote:
> >
> >
Hi,
> >
> > I downloaded Xen 4.0 and did:
> > make install
> > I donot see initrd (ramdisk) being created at all.
> >
> > Any suggestions ?
> >
>
> Step 5 of the README
> Depending on your config, you may need to use 'mkinitrd' to create
> an initial ram disk, just like a native system e.g.
> # depmod 2.6.18-xen
> # mkinitrd -v -f --with=aacraid --with=sd_mod --with=scsi_mod
> initrd-2.6.18-xen.img 2.6.18-xen
> Other systems may requires the use of 'mkinitramfs' to create
the
> ram disk.
> # depmod 2.6.18-xen
> # mkinitramfs -o initrd-2.6.18-xen.img 2.6.18-xen
>
> You may need to change the kernel version based on what you built.
> Also some distros use different commands to build initrd files.
>
> I actually forgot about this step for a second too.
>
> Thanks,
> Todd
>
> --
> Todd Deshane
> [2]http://todddeshane.net
> [3]http://runningxen.com
>
> References
>
> Visible links
> 1.
file:///mc/compose?to=ccmail111@yahoo.com
> 2. http://todddeshane.net/
> 3. http://runningxen.com/
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
[-- Attachment #1.2: Type: text/html, Size: 5538 bytes --]
[-- Attachment #2: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 15+ messages in thread* Re: boot Xen 4.0
2010-05-14 1:42 ccmail111
@ 2010-05-14 5:55 ` Pasi Kärkkäinen
2010-05-15 16:34 ` yingbin wang
1 sibling, 0 replies; 15+ messages in thread
From: Pasi Kärkkäinen @ 2010-05-14 5:55 UTC (permalink / raw)
To: ccmail111; +Cc: deshantm, xen-devel
On Thu, May 13, 2010 at 06:42:44PM -0700, ccmail111 wrote:
> Thanks Pasi/Todd,
>
> I did:
> # mkinitrd -v -f --builtin=ehci-hcd --builtin=ohci-hcd --builtin=uhci-hcd
> --builtin=ahci --builtin=aacraid --builtin=aacraid --builtin=sd_mod
> --builtin=scsi_mod /boot/initrd.img-2.6.31.13 2.6.31.13
>
> Now
> I see during boot: kernel panic:
>
> Mounting root filesystem.
> mount: could not find filesystem '/dev/root'
> setting up other filesystems
> setting up new root fs
> setuproot: moving /dev failed No such file or directory
> setuproot: error mounting /proc: No such file or directory
> setuproot: error mounting /sys: No such file or directory
> switchroot: mount failed: No such file or directory
> kernel panic - not syncing : Attempted to kill init !
>
So your root= parameter is wrong or initrd is wrong (not loading correct modules)..
please paste your grub.conf.
-- Pasi
> --- On Thu, 5/13/10, Pasi Kärkkäinen <pasik@iki.fi> wrote:
>
> From: Pasi Kärkkäinen <pasik@iki.fi>
> Subject: Re: [Xen-devel] initrd Xen 4.0
> To: "ccmail111" <ccmail111@yahoo.com>
> Cc: deshantm@gmail.com, xen-devel@lists.xensource.com
> Date: Thursday, May 13, 2010, 4:27 PM
>
> On Thu, May 13, 2010 at 01:08:36PM -0700, ccmail111 wrote:
> > The #5 of README is not clear in details.
> > which directory to run depmod and mkinitrd from ?
> >
>
> It doesn't matter.
>
> > I see:
> >
> > # depmod xen-4.0.0
> > WARNING: Couldn't find symtab and strtab in module xen-4.0.0
> >
>
> Wrong. You need to run depmod for the *kernel*, not for xen.
>
> So like this:
> depmod -a 2.6.32.12
>
> Or whatever is your kernel version.
>
> -- Pasi
>
> > # ls -l
> > total 1356
> > -rw-r--r-- 1 root root 1380620 May 13 13:05 xen-4.0.0
> >
> > Any suggestions ?
> >
> > --- On Wed, 5/12/10, Todd Deshane <deshantm@gmail.com> wrote:
> >
> > From: Todd Deshane <deshantm@gmail.com>
> > Subject: Re: [Xen-devel] initrd Xen 4.0
> > To: "ccmail111" <ccmail111@yahoo.com>
> > Cc: xen-devel@lists.xensource.com
> > Date: Wednesday, May 12, 2010, 9:46 PM
> >
> > Hi,
> >
> > See inline.
> >
> > On Wed, May 12, 2010 at 12:25 PM, ccmail111
> <[1]ccmail111@yahoo.com>
> > wrote:
> > >
> > > Hi,
> > >
> > > I downloaded Xen 4.0 and did:
> > > make install
> > > I donot see initrd (ramdisk) being created at all.
> > >
> > > Any suggestions ?
> > >
> >
> > Step 5 of the README
> > Depending on your config, you may need to use 'mkinitrd' to
> create
> > an initial ram disk, just like a native system e.g.
> > # depmod 2.6.18-xen
> > # mkinitrd -v -f --with=aacraid --with=sd_mod --with=scsi_mod
> > initrd-2.6.18-xen.img 2.6.18-xen
> > Other systems may requires the use of 'mkinitramfs' to create
> the
> > ram disk.
> > # depmod 2.6.18-xen
> > # mkinitramfs -o initrd-2.6.18-xen.img 2.6.18-xen
> >
> > You may need to change the kernel version based on what you
> built.
> > Also some distros use different commands to build initrd files.
> >
> > I actually forgot about this step for a second too.
> >
> > Thanks,
> > Todd
> >
> > --
> > Todd Deshane
> > [2][1]http://todddeshane.net
> > [3][2]http://runningxen.com
> >
> > References
> >
> > Visible links
> > 1. file:///mc/compose?to=ccmail111@yahoo.com
> > 2. [3]http://todddeshane.net/
> > 3. [4]http://runningxen.com/
>
> > _______________________________________________
> > Xen-devel mailing list
> > Xen-devel@lists.xensource.com
> > [5]http://lists.xensource.com/xen-devel
>
> References
>
> Visible links
> 1. http://todddeshane.net/
> 2. http://runningxen.com/
> 3. http://todddeshane.net/
> 4. http://runningxen.com/
> 5. http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: boot Xen 4.0
2010-05-14 1:42 ccmail111
2010-05-14 5:55 ` Pasi Kärkkäinen
@ 2010-05-15 16:34 ` yingbin wang
2010-05-17 20:17 ` ccmail111
1 sibling, 1 reply; 15+ messages in thread
From: yingbin wang @ 2010-05-15 16:34 UTC (permalink / raw)
To: ccmail111; +Cc: deshantm, xen-devel
I met similar problems and solved it.
if your grub.conf is OK, you can try to edit a option of your .config.
CONFIG_SYSFS_DEPRECATED_V2=y
2010/5/14 ccmail111 <ccmail111@yahoo.com>
>
> Thanks Pasi/Todd,
>
> I did:
> # mkinitrd -v -f --builtin=ehci-hcd --builtin=ohci-hcd --builtin=uhci-hcd --builtin=ahci --builtin=aacraid --builtin=aacraid --builtin=sd_mod --builtin=scsi_mod /boot/initrd.img-2.6.31.13 2.6.31.13
>
>
> Now
> I see during boot: kernel panic:
>
> Mounting root filesystem.
> mount: could not find filesystem '/dev/root'
> setting up other filesystems
> setting up new root fs
> setuproot: moving /dev failed No such file or directory
> setuproot: error mounting /proc: No such file or directory
> setuproot: error mounting /sys: No such file or directory
> switchroot: mount failed: No such file or directory
> kernel panic - not syncing : Attempted to kill init !
>
>
>
>
> --- On Thu, 5/13/10, Pasi Kärkkäinen <pasik@iki.fi> wrote:
>
> From: Pasi Kärkkäinen <pasik@iki.fi>
> Subject: Re: [Xen-devel] initrd Xen 4.0
> To: "ccmail111" <ccmail111@yahoo.com>
> Cc: deshantm@gmail.com, xen-devel@lists.xensource.com
> Date: Thursday, May 13, 2010, 4:27 PM
>
> On Thu, May 13, 2010 at 01:08:36PM -0700, ccmail111 wrote:
> > The #5 of README is not clear in details.
> > which directory to run depmod and mkinitrd from ?
> >
>
> It doesn't matter.
>
> > I see:
> >
> > # depmod xen-4.0.0
> > WARNING: Couldn't find symtab and strtab in module xen-4.0.0
> >
>
> Wrong. You need to run depmod for the *kernel*, not for xen.
>
> So like this:
> depmod -a 2.6.32.12
>
> Or whatever is your kernel version.
>
> -- Pasi
>
> > # ls -l
> > total 1356
> > -rw-r--r-- 1 root root 1380620 May 13 13:05 xen-4.0.0
> >
> > Any suggestions ?
> >
> > --- On Wed, 5/12/10, Todd Deshane <deshantm@gmail.com> wrote:
> >
> > From: Todd Deshane <deshantm@gmail.com>
> > Subject: Re: [Xen-devel] initrd Xen 4.0
> > To: "ccmail111" <ccmail111@yahoo.com>
> > Cc: xen-devel@lists.xensource.com
> > Date: Wednesday, May 12, 2010, 9:46 PM
> >
> > Hi,
> >
> > See inline.
> >
> > On Wed, May 12, 2010 at 12:25 PM, ccmail111 <[1]ccmail111@yahoo.com>
> > wrote:
> > >
> > > Hi,
> > >
> > > I downloaded Xen 4.0 and did:
> > > make install
> > > I donot see initrd (ramdisk) being created at all.
> > >
> > > Any suggestions ?
> > >
> >
> > Step 5 of the README
> > Depending on your config, you may need to use 'mkinitrd' to create
> > an initial ram disk, just like a native system e.g.
> > # depmod 2.6.18-xen
> > # mkinitrd -v -f --with=aacraid --with=sd_mod --with=scsi_mod
> > initrd-2.6.18-xen.img 2.6.18-xen
> > Other systems may requires the use of 'mkinitramfs' to create the
> > ram disk.
> > # depmod 2.6.18-xen
> > # mkinitramfs -o initrd-2.6.18-xen.img 2.6.18-xen
> >
> > You may need to change the kernel version based on what you built.
> > Also some distros use different commands to build initrd files.
> >
> > I actually forgot about this step for a second too.
> >
> > Thanks,
> > Todd
> >
> > --
> > Todd Deshane
> > [2]http://todddeshane.net
> > [3]http://runningxen.com
> >
> > References
> >
> > Visible links
> > 1. file:///mc/compose?to=ccmail111@yahoo.com
> > 2. http://todddeshane.net/
> > 3. http://runningxen.com/
>
> > _______________________________________________
> > Xen-devel mailing list
> > Xen-devel@lists.xensource.com
> > http://lists.xensource.com/xen-devel
>
>
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
>
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: boot Xen 4.0
2010-05-15 16:34 ` yingbin wang
@ 2010-05-17 20:17 ` ccmail111
0 siblings, 0 replies; 15+ messages in thread
From: ccmail111 @ 2010-05-17 20:17 UTC (permalink / raw)
To: yingbin wang; +Cc: deshantm, xen-devel
[-- Attachment #1.1: Type: text/plain, Size: 6952 bytes --]
Hi Yingbin,
Thanks, I tried but no progress.
I see during boot kernel stuck at:
usb usb6: Manufacturer: Linux 2.6.31.13 uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.0
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
xen: registering gsi 16 triggering 0 polarity 1
xen_allocate_pirq: returning irq 16 for gsi 16
xen: --> irq=16
xen_set_ioapic_routing: irq 16 gsi 16 vector 16 ioapic 0 pin 16 triggering 1 polarity 1
(XEN) io_apic.c:2290:
(XEN) ioapic_guest_write: apic=0, pin=16, irq=16
(XEN) ioapic_guest_write: new_entry=0001a998
(XEN) ioapic_guest_write: old_entry=0000a998 pirq=16
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
uhci_hcd 0000:00:1d.1: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: irq 16, io base 0x00004040
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.31.13 uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.1
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
xen: registering gsi 16 triggering 0 polarity 1
xen_allocate_pirq: returning irq 16 for gsi 16
xen: --> irq=16
xen_set_ioapic_routing: irq 16 gsi 16 vector 16 ioapic 0 pin 16 triggering 1 polarity 1
(XEN) io_apic.c:2290:
(XEN) ioapic_guest_write: apic=0, pin=16, irq=16
(XEN) ioapic_guest_write: new_entry=0001a998
(XEN) ioapic_guest_write: old_entry=0000a998 pirq=16
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
uhci_hcd 0000:00:1d.2: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: irq 16, io base 0x00004020
usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
usb usb8: New USB device strings: Mfr=3, Product=2, Serial
<<<< stuck here...
grub conf is:
title Xen 4.0 debug XenLinux 2.6
root (hd0,0)
kernel /xen-4.0.0.gz console=com1, com1=115200,8n1 noreboot loglvl=all vv
ga=text-80x50,keep iommu=off apic=debug guest_loglvl=all
module /vmlinuz-2.6.31.13 ro root=/dev/ram0 console=hvc0 earlyprintk=xee
n nomodeset initcall_debug debug loglevel=10
module /initrd.img-2.6.31.13
Any suggestions ?
CM
--- On Sat, 5/15/10, yingbin wang <yingbin.wangyb@gmail.com> wrote:
From: yingbin wang <yingbin.wangyb@gmail.com>
Subject: Re: [Xen-devel] boot Xen 4.0
To: "ccmail111" <ccmail111@yahoo.com>
Cc: "Pasi Kärkkäinen" <pasik@iki.fi>, deshantm@gmail.com, xen-devel@lists.xensource.com
Date: Saturday, May 15, 2010, 12:34 PM
I met similar problems and solved it.
if your grub.conf is OK, you can try to edit a option of your .config.
CONFIG_SYSFS_DEPRECATED_V2=y
2010/5/14 ccmail111 <ccmail111@yahoo.com>
>
> Thanks Pasi/Todd,
>
> I did:
> # mkinitrd -v -f --builtin=ehci-hcd --builtin=ohci-hcd --builtin=uhci-hcd --builtin=ahci --builtin=aacraid --builtin=aacraid --builtin=sd_mod --builtin=scsi_mod /boot/initrd.img-2.6.31.13 2.6.31.13
>
>
> Now
> I see during boot: kernel panic:
>
> Mounting root filesystem.
> mount: could not find filesystem '/dev/root'
> setting up other filesystems
> setting up new root fs
> setuproot: moving /dev failed No such file or directory
> setuproot: error mounting /proc: No such file or directory
> setuproot: error mounting /sys: No such file or directory
> switchroot: mount failed: No such file or directory
> kernel panic - not syncing : Attempted to kill init !
>
>
>
>
> --- On Thu, 5/13/10, Pasi Kärkkäinen <pasik@iki.fi> wrote:
>
> From: Pasi Kärkkäinen <pasik@iki.fi>
> Subject: Re: [Xen-devel] initrd Xen 4.0
> To: "ccmail111" <ccmail111@yahoo.com>
> Cc: deshantm@gmail.com, xen-devel@lists.xensource.com
> Date: Thursday, May 13, 2010, 4:27 PM
>
> On Thu, May 13, 2010 at 01:08:36PM -0700, ccmail111 wrote:
> > The #5 of README is not clear in details.
> > which directory to run depmod and mkinitrd from ?
> >
>
> It doesn't matter.
>
> > I see:
> >
> > # depmod xen-4.0.0
> > WARNING: Couldn't find symtab and strtab in module xen-4.0.0
> >
>
> Wrong. You need to run depmod for the *kernel*, not for xen.
>
> So like this:
> depmod -a 2.6.32.12
>
> Or whatever is your kernel version.
>
> -- Pasi
>
> > # ls -l
> > total 1356
> > -rw-r--r-- 1 root root 1380620 May 13 13:05 xen-4.0.0
> >
> > Any suggestions ?
> >
> > --- On Wed, 5/12/10, Todd Deshane <deshantm@gmail.com> wrote:
> >
> > From: Todd Deshane <deshantm@gmail.com>
> > Subject: Re: [Xen-devel] initrd Xen 4.0
> > To: "ccmail111" <ccmail111@yahoo.com>
> > Cc: xen-devel@lists.xensource.com
> > Date: Wednesday, May 12, 2010, 9:46 PM
> >
> > Hi,
> >
> > See inline.
> >
> > On Wed, May 12, 2010 at 12:25 PM, ccmail111 <[1]ccmail111@yahoo.com>
> > wrote:
> > >
> > > Hi,
> > >
> > > I downloaded Xen 4.0 and did:
> > > make install
> > > I donot see initrd (ramdisk) being created at all.
> > >
> > > Any suggestions ?
> > >
> >
> > Step 5 of the README
> > Depending on your config, you may need to use 'mkinitrd' to create
> > an initial ram disk, just like a native system e.g.
> > # depmod 2.6.18-xen
> > # mkinitrd -v -f --with=aacraid --with=sd_mod --with=scsi_mod
> > initrd-2.6.18-xen.img 2.6.18-xen
> > Other systems may requires the use of 'mkinitramfs' to create the
> > ram disk.
> > # depmod 2.6.18-xen
> > # mkinitramfs -o initrd-2.6.18-xen.img 2.6.18-xen
> >
> > You may need to change the kernel version based on what you built.
> > Also some distros use different commands to build initrd files.
> >
> > I actually forgot about this step for a second too.
> >
> > Thanks,
> > Todd
> >
> > --
> > Todd Deshane
> > [2]http://todddeshane.net
> > [3]http://runningxen.com
> >
> > References
> >
> > Visible links
> > 1. file:///mc/compose?to=ccmail111@yahoo.com
> > 2. http://todddeshane.net/
> > 3. http://runningxen.com/
>
> > _______________________________________________
> > Xen-devel mailing list
> > Xen-devel@lists.xensource.com
> > http://lists.xensource.com/xen-devel
>
>
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
>
[-- Attachment #1.2: Type: text/html, Size: 10960 bytes --]
[-- Attachment #2: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2010-06-22 17:30 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-06-04 20:30 boot Xen 4.0 ccmail111
2010-06-04 20:34 ` Konrad Rzeszutek Wilk
-- strict thread matches above, loose matches on Subject: below --
2010-06-21 20:54 ccmail111
2010-06-22 17:30 ` Konrad Rzeszutek Wilk
2010-06-17 18:27 ccmail111
2010-06-10 16:02 ccmail111
2010-06-15 21:26 ` Konrad Rzeszutek Wilk
2010-05-18 19:08 ccmail111
2010-05-18 19:11 ` Pasi Kärkkäinen
2010-05-18 21:46 ` ccmail111
2010-05-26 17:44 ` Konrad Rzeszutek Wilk
2010-05-14 1:42 ccmail111
2010-05-14 5:55 ` Pasi Kärkkäinen
2010-05-15 16:34 ` yingbin wang
2010-05-17 20:17 ` ccmail111
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).