From mboxrd@z Thu Jan  1 00:00:00 1970
From: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Subject: Re: Bug in PCI Passthrough
Date: Wed, 20 Apr 2011 15:38:37 -0400
Message-ID: <20110420193836.GA32696@dumpdata.com>
References: <4DAEA42B.3010600@li-life.li> <20110420125155.GA4534@dumpdata.com>
	<4DAF310F.4000401@li-life.li>
Mime-Version: 1.0
Content-Type: text/plain; charset=us-ascii
Return-path: <xen-devel-bounces@lists.xensource.com>
Content-Disposition: inline
In-Reply-To: <4DAF310F.4000401@li-life.li>
List-Unsubscribe: <http://lists.xensource.com/mailman/listinfo/xen-devel>,
	<mailto:xen-devel-request@lists.xensource.com?subject=unsubscribe>
List-Post: <mailto:xen-devel@lists.xensource.com>
List-Help: <mailto:xen-devel-request@lists.xensource.com?subject=help>
List-Subscribe: <http://lists.xensource.com/mailman/listinfo/xen-devel>,
	<mailto:xen-devel-request@lists.xensource.com?subject=subscribe>
Sender: xen-devel-bounces@lists.xensource.com
Errors-To: xen-devel-bounces@lists.xensource.com
To: Josef Vogt <josef.vogt@li-life.li>
Cc: xen-devel@lists.xensource.com
List-Id: xen-devel@lists.xenproject.org

On Wed, Apr 20, 2011 at 09:16:31PM +0200, Josef Vogt wrote:
> Am 20.04.2011 14:51, schrieb Konrad Rzeszutek Wilk:
> >On Wed, Apr 20, 2011 at 11:15:23AM +0200, Josef Vogt wrote:
> >>Hello all
> >>
> >>I tried to enable PCI Passthrough in my Debian Squeeze installation.
> >>Unfortunately, it didnt work. The following bug showed up (excerpt
> >>from dmesg):
> >>
> >>[ 10.148612] uhci_hcd 0000:00:14.2: PCI INT D ->  Link[LNKD] ->  GSI 11
> >>(level, low) ->  IRQ 11
> >>[ 4.678352] Failed to setup GSI :11, err_code:-22
> >>[ 4.678480] dmfe 0000:00:0e.0: PCI INT A ->  Link[LNKB] ->  GSI 11 (level,
> >>low) ->  IRQ 11
> >>[ 6.868419] Failed to setup GSI :10, err_code:-22
> >That is most strange. Your interrupts are below IRQ 16, and they are level?
> >They should have been edge, unless you have some strange machine.
> >
> Hm... it's a rather old one: Compaq Deskpro PD1006 (Pentium III)

Can you boot the same kernel but without Xen and send the bootup output?
And also the /proc/interrupts (the full one).
> 
> >If you don't pass in the card to the DomU, but run it under Dom0, what is
> >the GSI and /proc/interrupts for the dmfe?
> 
> /proc/interrupts for dmfe in Dom0 (card is up and running, I disabled the other):
> cat /proc/interrupts | grep eth
> 11:        893  xen-pirq-xt-pic    uhci_hcd:usb1, eth0
> 
> GSI: I'm not so sure what you mean but this must be GSI 11 (see above or dmesg in attachment)

<blinks> Well, it looks like your motherboard has the IRQs below 16 to be level.
That is odd. 
> 
> >Can you also attach the full serial output? (so we can see the Xen hypervisor output
> >and the Linux Dom0 output).
> This is what i get (see attached logs)

Thank you.