Re: Windows 8 VGA Passthrough

[John Wargo <wargo.john25@gmail.com>]

On 10/27/2013 02:35 PM, Gordan Bobic wrote:
> On 10/27/2013 04:21 PM, John Wargo wrote:
>> On 10/27/2013 09:27 AM, John Wargo wrote:
>>> On 10/27/2013 04:30 AM, Gordan Bobic wrote:
>>>> On 10/26/2013 09:58 PM, John Wargo wrote:
>>>>> Geniuses,
>>>>>
>>>>> I've been trying to get VGA pass-through working on Windows 8, 
>>>>> however
>>>>> I've been running into a few issues.
>>>>> Currently I can get Windows 8 running flawlessly without VGA
>>>>> pass-through, however I'm planning on using it for gaming, so this 
>>>>> wont
>>>>> work.
>>>>>
>>>>> When I start windows 8, I am able to get past the install portion of
>>>>> the
>>>>> DVD, however it hangs on "Getting devices ready.. (n%)".
>>>>>
>>>>> Hardware Information :
>>>>> AMD Fx6300
>>>>> ASUS M5a99x evo r2.0
>>>>> 16GB RAM
>>>>> 6670 Radeon HD - Dom0
>>>>> 7850 Radeon HD - Win8
>>>>
>>>> I have recently (recently as in over the past 48 hours) re-tried to
>>>> get ATI VGA passthrough working, and the results are... interesting.
>>>>
>>>> HD4850 dom0 + HD7450 domU worked fine - or as fine as ATI passthrough
>>>> ever seems to work (slowdown + white lines when dragging windows
>>>> after a domU reboot). I am using XP64 domU so I can't eject the GPU
>>>> (it says it is being used). But shutting down the domU, doing echo 1
>>>> > reset for the GPU from dom0 (I don't know how this is implemented
>>>> and whether it does anything) and then starting it up again sometimes
>>>> recovers it. GPU-Z runs and reports the GPU correctly.
>>>>
>>>> HD4850 dom0 + HD7970 domU results in the entire host locking up as
>>>> soon as the driver is loaded in domU. My solution is to swap the dom0
>>>> GPU for an 8800GT, and the problem now doesn't occur. If I had to
>>>> guess, BIOS on the HD7970 does something bizzare, finds the HD4850 on
>>>> the bus, tries to do something to it, and ends up crashing the host.
>>>> This could also be exacerbated by the fact that I have to run with
>>>> relaxed checking and no PCI ACS due to NF200 bridges on my
>>>> motherboard. Even so, however, GPU-Z crashes the domU and it's GPU
>>>> _hard_ (but not the host, thankfully). It crashes it so hard, that
>>>> the only cure is to reboot the host. Reseting the GPU via /sys/
>>>> doesn't seem to do anything to help.
>>>>
>>>> Are you using gfx_passthru=1 in your config? The way most people have
>>>> this kind of thing working is with gfx_passthru=0, i.e. secondary
>>>> passthru. Don't assign the PCI device in the config when installing.
>>>> Once the domU install is complete, shut it down, and add the GPU you
>>>> want to pass through. Then fire up domU in VNC, install the driver,
>>>> and with a bit of luck it will come up with output on the external
>>>> monitor.
>>>>
>>>> Also make sure that radeon or radeonfb kernel drivers DO NOT load
>>>> before the device is assigned to xen-pciback. The exact way to ensure
>>>> this will depend on what distro and dom0 kernel you are using.
>>>>
>>>> Gordan
>>> Status update:
>>>
>>> The catalyst drivers appear to be working perfectly fine, device
>>> manager shows no errors, and everything works great, except that when
>>> I plug my monitor into the second card, I get "No Signal" on the
>>> monitor, then it shuts off.
>>>
>>> I though that secondary passthrough meant that it would pass the
>>> virtual adapter in as primary, but I could use my GPU that I passed
>>> through, so where am I wrong, and how do I do that?
>>>
>>> -John
>> I've been doing some research into my VGA passthrough, so I've gone
>> through the various debugging steps, and the only thing that I've found
>> out of place is with "xl dmesg" (attached).
>>
>> Where do I go from here?
>
> Sounds like your IOMMU may be buggy. You may need to set permissive=1 
> on your xen-pciback module.
>
> I cannot remember if xl uses the same configuration, but for xm you 
> could try putting this in your /etc/xen/xend-config.sxp:
> (pci-passthrough-strict-check no)
> (pci-dev-assign-strict-check no)
>
> Gordan
>
Gordan,

After a bit of research, I was able to activate permissive mode on xen, 
but I've got nothing, I'm still getting page faults.

The page faults occur when the loading screen goes black (I'd assume 
when it's trying to pass to the GPU)

I've also tried setting (pci_msitranslate=0, along with changing 
qemu=qemu-xen, but it doesn't help

-John