From: Julien Grall <julien.grall@arm.com>
To: George John <georgeeldhojohn@gmail.com>, xen-devel@lists.xenproject.org
Cc: nd@arm.com
Subject: Re: Error in Xen while booting for salvator-X (M3 Board)
Date: Fri, 24 Feb 2017 14:53:38 +0000 [thread overview]
Message-ID: <6b4a6e23-aacb-99ec-3445-ff860611b3fa@arm.com> (raw)
In-Reply-To: <CANou6SrNz4QbhyZRaWKyQ1W8VZdfXYoP_nThzBWxyhoS-dFKBw@mail.gmail.com>
On 21/02/17 12:03, George John wrote:
> Hi,
Hello,
> I was trying out xen in salvator-X(M3 Board as described
> in https://wiki.xenproject.org/wiki/Xen_ARM_with_Virtualization_Extensions/Salvator-X
>
> I ran in to following error:
>
>
> U-Boot 2015.04 (Feb 21 2017 - 14:24:48)
>
> CPU: Renesas Electronics R8A7796 rev 1.0
> Board: Salvator-X
> I2C: ready
> DRAM: 3.9 GiB
> MMC: sh-sdhi: 0, sh-sdhi: 1, sh-sdhi: 2
> In: serial
> Out: serial
> Err: serial
> Net: Board Net Initialization Failed
> No ethernet found.
> Hit any key to stop autoboot: 0
> 819584 bytes read in 89 ms (8.8 MiB/s)
> 64927 bytes read in 23 ms (2.7 MiB/s)
> 14038016 bytes read in 1188 ms (11.3 MiB/s)
> 10319 bytes read in 19 ms (530.3 KiB/s)
> ## Booting kernel from Legacy Image at 48080000 ...
> Image Name: XEN
> Image Type: AArch64 Linux Kernel Image (uncompressed)
> Data Size: 819520 Bytes = 800.3 KiB
> Load Address: 78080000
> Entry Point: 78080000
> Verifying Checksum ... OK
> ## Flattened Device Tree blob at 48000000
> Booting using the fdt blob at 0x48000000
> Loading Kernel Image ... OK
> Using Device Tree in place at 0000000048000000, end 0000000048012d9e
>
> Starting kernel ...
>
> - UART enabled -
> - CPU 00000000 booting -
> - Current EL 00000008 -
> - Xen starting at EL2 -
> - Zero BSS -
> - Setting up control registers -
> - Turning on paging -
> - Ready -
> (XEN) Checking for initrd in /chosen
> (XEN) RAM: 0000000048000000 - 000000007fffffff
> (XEN) RAM: 0000000500000000 - 000000053fffffff
> (XEN) RAM: 0000000600000000 - 000000063fffffff
> (XEN) RAM: 0000000700000000 - 000000073fffffff
> (XEN)
> (XEN) MODULE[0]: 0000000048000000 - 0000000048010000 Device Tree
> (XEN) MODULE[1]: 000000007a000000 - 000000007c000000 Kernel
> (XEN) MODULE[2]: 000000007c000000 - 000000007c010000 XSM
> (XEN) RESVD[0]: 0000000048000000 - 0000000048010000
> (XEN)
> (XEN) Command line: dom0_mem=512M console=dtuart dtuart=serial0
> dom0_max_vcpus=1 bootscrub=0 flask_enforcing=1
> (XEN) Placing Xen at 0x000000007fe00000-0x0000000080000000
> (XEN) Update BOOTMOD_XEN from 0000000078080000-0000000078196e01 =>
> 000000007fe00000-000000007ff16e01
Which kernel version is it?
>
>
>
>
>
>
> After this, it hangs. What could be the possible reason?
Xen will initialize the heap and then continue into the boot. I would
add more debug around setup_mm to see where it failed.
Regards,
--
Julien Grall
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xen.org
https://lists.xen.org/xen-devel
next prev parent reply other threads:[~2017-02-24 14:53 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-02-21 12:03 Error in Xen while booting for salvator-X (M3 Board) George John
2017-02-24 14:53 ` Julien Grall [this message]
2017-02-24 15:13 ` Oleksandr Tyshchenko
2017-02-27 10:29 ` George John
2017-02-27 10:48 ` Oleksandr Tyshchenko
2017-02-27 10:55 ` Oleksandr Andrushchenko
2017-02-28 15:01 ` George John
2017-02-27 10:52 ` Andrii Anisov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=6b4a6e23-aacb-99ec-3445-ff860611b3fa@arm.com \
--to=julien.grall@arm.com \
--cc=georgeeldhojohn@gmail.com \
--cc=nd@arm.com \
--cc=xen-devel@lists.xenproject.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).