From: chris <tknchris@gmail.com>
To: "Pasi Kärkkäinen" <pasik@iki.fi>
Cc: Xen-Devel List <xen-devel@lists.xensource.com>,
Xen-Users List <xen-users@lists.xensource.com>
Subject: Re: [Xen-users] RE: Xen4 / Intel DX58SO Mobo / VT-d not working
Date: Fri, 14 May 2010 17:17:43 -0400 [thread overview]
Message-ID: <AANLkTinL35-_rYMMAhNLoxhORR615ag5oUv7_bNrG3a9@mail.gmail.com> (raw)
In-Reply-To: <20100514205000.GL17817@reaktio.net>
[-- Attachment #1: Type: text/plain, Size: 38333 bytes --]
Played around with xen_platform_pc, pci_msitranslate, pci_power_mgmt
in the cfg, none of which seem to have any effect, also tried
pci=resource_alignment=02:00.0;02:00.1;02:00.2 on dom0 cmdline, no
effect.
I'm worn out been fighting this all day. Attached is some various
output from the machine that works with the same cards and has Xen
3.4.2 and the new machine with 4.0 which doesn't work. I'm hoping this
information can get the right attention and we can figure it out :(
- chris
On Fri, May 14, 2010 at 4:50 PM, Pasi Kärkkäinen <pasik@iki.fi> wrote:
> On Fri, May 14, 2010 at 04:39:54PM -0400, chris wrote:
>> Alright so a pci sound card works, I tried a geforce 8600 pci e card
>> and while vga passthrough didnt work it did seem to attach to the
>> domain ok. So I guess the problem must be somehow related to the
>> device. I'm still confused since it works in another box.
>>
>> I remember there was some reassign_resources or something, maybe the
>> issue is with some resources the card uses?
>>
>
> http://wiki.xensource.com/xenwiki/XenPCIpassthrough
>
> -- Pasi
>
>> Below is a lspci -vv of the card
>>
>> 02:00.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
>> Subsystem: NEC Corporation Hama USB 2.0 CardBus
>> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B- DisINTx-
>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>> >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>> Interrupt: pin A routed to IRQ 16
>> Region 0: Memory at d2502000 (32-bit, non-prefetchable)
>> [disabled] [size=4K]
>> Capabilities: [40] Power Management version 2
>> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
>> PME(D0+,D1+,D2+,D3hot+,D3cold-)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>> Kernel driver in use: pciback
>>
>> 02:00.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
>> Subsystem: NEC Corporation Hama USB 2.0 CardBus
>> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B- DisINTx-
>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>> >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>> Interrupt: pin B routed to IRQ 17
>> Region 0: Memory at d2501000 (32-bit, non-prefetchable)
>> [disabled] [size=4K]
>> Capabilities: [40] Power Management version 2
>> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
>> PME(D0+,D1+,D2+,D3hot+,D3cold-)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>> Kernel driver in use: pciback
>>
>> 02:00.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
>> Subsystem: NEC Corporation USB 2.0
>> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B- DisINTx-
>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>> >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>> Interrupt: pin C routed to IRQ 18
>> Region 0: Memory at d2500000 (32-bit, non-prefetchable)
>> [disabled] [size=256]
>> Capabilities: [40] Power Management version 2
>> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
>> PME(D0+,D1+,D2+,D3hot+,D3cold-)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>> Kernel driver in use: pciback
>>
>>
>> On Fri, May 14, 2010 at 3:46 PM, chris <tknchris@gmail.com> wrote:
>> > I added a pci sound card and interestingly that works. I'm digging
>> > around for another pci-e device to try to identify if its all pci-e or
>> > only this device. Strange this is that I have a few other machines
>> > with this same usb controller which is working on 3.4.2.
>> >
>> > *scratches head*
>> >
>> > - chris
>> >
>> > On Fri, May 14, 2010 at 3:21 PM, Pasi Kärkkäinen <pasik@iki.fi> wrote:
>> >> On Fri, May 14, 2010 at 03:18:02PM -0400, chris wrote:
>> >>> It is a multifunction device, a pci-e usb controller, so I assumed all
>> >>> them had to be passed through. I just changed it to only 02:00.0 and
>> >>> same thing
>> >>>
>> >>> test-box2:~# cat /etc/xen/vm-five.cfg | grep pci
>> >>> pci = ['02:00.0']
>> >>> test-box2:~# xm create /etc/xen/vm-five.cfg
>> >>> Using config file "/etc/xen/vm-five.cfg".
>> >>> Error: Failed to assign device to IOMMU
>> >>> (0000:02:00.0@100,msitranslate=1,power_mgmt=0)
>> >>>
>> >>
>> >> Hmm.. weird.
>> >>
>> >> Two things to try:
>> >>
>> >> 1) Try passthru some other device (which is just a single pci id)
>> >> 2) Try passthru that pci-e usb controller to Linux PV guest and see if that works
>> >>
>> >> -- Pasi
>> >>
>> >>>
>> >>> On Fri, May 14, 2010 at 3:11 PM, Pasi Kärkkäinen <pasik@iki.fi> wrote:
>> >>> > On Fri, May 14, 2010 at 03:05:49PM -0400, chris wrote:
>> >>> >> Pasi,
>> >>> >>
>> >>> >> Tried latest stable/2.6.32.x per your advice, no change. Anyone on
>> >>> >> xen-devel that can help me troubleshoot further? Everything looks
>> >>> >> right, can't figure out why vt-d is not working but it must be some
>> >>> >> kind of bug :(
>> >>> >>
>> >>> >
>> >>> > Did you try the suggestion said earlier.. try to just passthru the first pci device?
>> >>> >
>> >>> > -- Pasi
>> >>> >
>> >>> >> test-box2:~# uname -a
>> >>> >> Linux test-box2 2.6.32.12 #1 SMP Fri May 14 13:40:05 EDT 2010 x86_64 GNU/Linux
>> >>> >>
>> >>> >> test-box2:~# xm info | grep virt_caps
>> >>> >> virt_caps : hvm hvm_directio
>> >>> >>
>> >>> >> test-box2:~# xm pci-list-assignable-devices
>> >>> >> 0000:02:00.0
>> >>> >> 0000:02:00.1
>> >>> >> 0000:02:00.2
>> >>> >>
>> >>> >> test-box2:~# xm create /etc/xen/vm-five.cfg
>> >>> >> Using config file "/etc/xen/vm-five.cfg".
>> >>> >> Error: Failed to assign device to IOMMU
>> >>> >> (0000:02:00.0@100,msitranslate=1,power_mgmt=0)
>> >>> >>
>> >>> >> test-box2:~# cat /etc/xen/vm-five.cfg | grep -v '#'
>> >>> >> kernel = '/usr/lib/xen/boot/hvmloader'
>> >>> >> builder = 'hvm'
>> >>> >> memory = '1792'
>> >>> >> device_model='/usr/lib/xen/bin/qemu-dm'
>> >>> >> disk = [ 'phy:/dev/storage/vm-five,ioemu:hda,w',
>> >>> >> 'phy:/dev/sr0,ioemu:hdc:cdrom,r'
>> >>> >> ]
>> >>> >> name = 'vm-five'
>> >>> >> vif = ['type=ioemu, bridge=eth0, mac=00:16:3D:37:A1:42']
>> >>> >> boot='dc'
>> >>> >> cpus='0-1'
>> >>> >> vcpus=2
>> >>> >> acpi=1
>> >>> >> ahci=1
>> >>> >> vnc=1
>> >>> >> sdl=0
>> >>> >> timer_mode=1
>> >>> >> usb=1
>> >>> >> usbdevice='tablet'
>> >>> >> localtime=1
>> >>> >> pci = ['02:00.0','02:00.1','02:00.2']
>> >>> >>
>> >>> >> On Thu, May 13, 2010 at 2:28 PM, chris <tknchris@gmail.com> wrote:
>> >>> >> > Forwarding to xen-devel. Can't seem to get VT-d working with xen4 from
>> >>> >> > tarball on xen.org 2.6.31.13 pv_ops dom0. On pasi's advice I tried
>> >>> >> > switching to stable/2.6.32.x branch for dom0 and that doesnt even
>> >>> >> > build. Did something change recently thats breaking compilation?
>> >>> >> >
>> >>> >> > Attached is xen dmesg with iommu=verbose loglvl=all guest_loglvl=all,
>> >>> >> > and dom0 dmesg from 2.6.31.x
>> >>> >> >
>> >>> >> > Any ideas on why VT-d is not working on this board? Initialization
>> >>> >> > looks good, xen reports hvm_directio capability, everything says VT-d
>> >>> >> > should work until domain is created.
>> >>> >> >
>> >>> >> > Any ideas why stable/2.6.32.x wont build?
>> >>> >> >
>> >>> >> > - chris
>> >>> >> >
>> >>> >> > On Thu, May 13, 2010 at 2:07 PM, chris <tknchris@gmail.com> wrote:
>> >>> >> >> I redid it with oldconfig which I didn't think would help and same
>> >>> >> >> thing. I guess this tree is broken? Can someone else try and see if
>> >>> >> >> they can build it? Ugh, whata day :)
>> >>> >> >>
>> >>> >> >> On Thu, May 13, 2010 at 1:58 PM, Pasi Kärkkäinen <pasik@iki.fi> wrote:
>> >>> >> >>> On Thu, May 13, 2010 at 01:55:25PM -0400, chris wrote:
>> >>> >> >>>> I used the default config on the wiki which you created. Steps I took were:
>> >>> >> >>>>
>> >>> >> >>>> # make clean distclean
>> >>> >> >>>> # wget -O .config
>> >>> >> >>>> "http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.10-pvops-dom0-xen-stable-x86_64"
>> >>> >> >>>
>> >>> >> >>> You should do "make oldconfig" at this point.
>> >>> >> >>>
>> >>> >> >>>> # make -j8 bzImage
>> >>> >> >>>> (blah blah)
>> >>> >> >>>> LD vmlinux.o
>> >>> >> >>>> MODPOST vmlinux.o
>> >>> >> >>>> WARNING: modpost: Found 7 section mismatch(es).
>> >>> >> >>>> To see full details build your kernel with:
>> >>> >> >>>> 'make CONFIG_DEBUG_SECTION_MISMATCH=y'
>> >>> >> >>>> GEN .version
>> >>> >> >>>> CHK include/linux/compile.h
>> >>> >> >>>> UPD include/linux/compile.h
>> >>> >> >>>> CC init/version.o
>> >>> >> >>>> LD init/built-in.o
>> >>> >> >>>> LD .tmp_vmlinux1
>> >>> >> >>>> drivers/built-in.o: In function `do_hvm_suspend':
>> >>> >> >>>> /mnt/tmp/linux-2.6-xen/drivers/xen/manage.c:124: undefined reference
>> >>> >> >>>> to `xenbus_suspend'
>> >>> >> >>>> /mnt/tmp/linux-2.6-xen/drivers/xen/manage.c:138: undefined reference
>> >>> >> >>>> to `xenbus_resume'
>> >>> >> >>>> make: *** [.tmp_vmlinux1] Error 1
>> >>> >> >>>>
>> >>> >> >>>
>> >>> >> >>> Hmm.. weird. I wonder if something has changed recently or what's going on in here..
>> >>> >> >>>
>> >>> >> >>> -- Pasi
>> >>> >> >>>
>> >>> >> >>>>
>> >>> >> >>>> On Thu, May 13, 2010 at 11:47 AM, Pasi Kärkkäinen <pasik@iki.fi> wrote:
>> >>> >> >>>> > On Thu, May 13, 2010 at 11:33:57AM -0400, chris wrote:
>> >>> >> >>>> >> Successfully grabbed the sources and failed to build:
>> >>> >> >>>> >>
>> >>> >> >>>> >> LD .tmp_vmlinux1
>> >>> >> >>>> >> drivers/built-in.o: In function `do_hvm_suspend':
>> >>> >> >>>> >> /mnt/tmp/linux-2.6-xen/drivers/xen/manage.c:124: undefined reference
>> >>> >> >>>> >> to `xenbus_suspend'
>> >>> >> >>>> >> /mnt/tmp/linux-2.6-xen/drivers/xen/manage.c:138: undefined reference
>> >>> >> >>>> >> to `xenbus_resume'
>> >>> >> >>>> >> make: *** [.tmp_vmlinux1] Error 1
>> >>> >> >>>> >>
>> >>> >> >>>> >> :(
>> >>> >> >>>> >>
>> >>> >> >>>> >
>> >>> >> >>>> > Try the example .config files provided on the wiki page.
>> >>> >> >>>> >
>> >>> >> >>>> > -- Pasi
>> >>> >> >>>> >
>> >>> >> >>>> >> On Thu, May 13, 2010 at 10:14 AM, Pasi Kärkkäinen <pasik@iki.fi> wrote:
>> >>> >> >>>> >> > On Thu, May 13, 2010 at 10:12:56AM -0400, chris wrote:
>> >>> >> >>>> >> >> Pasi,
>> >>> >> >>>> >> >>
>> >>> >> >>>> >> >> How do I pull those kernel sources you referenced? I see it mentioned
>> >>> >> >>>> >> >> on http://wiki.xensource.com/xenwiki/XenParavirtOps but no details on
>> >>> >> >>>> >> >> how to retrieve it.
>> >>> >> >>>> >> >>
>> >>> >> >>>> >> >
>> >>> >> >>>> >> > The instructions are there if you read it carefully..
>> >>> >> >>>> >> > There's the topic of how to switch branches.
>> >>> >> >>>> >> >
>> >>> >> >>>> >> > -- Pasi
>> >>> >> >>>> >> >
>> >>> >> >>>> >> >> - chris
>> >>> >> >>>> >> >>
>> >>> >> >>>> >> >> On Thu, May 13, 2010 at 8:29 AM, Pasi Kärkkäinen <pasik@iki.fi> wrote:
>> >>> >> >>>> >> >> > On Wed, May 12, 2010 at 08:41:34PM -0400, chris wrote:
>> >>> >> >>>> >> >> >> When reading the vtdhowto I noticed the ability to set iommu=verbose.
>> >>> >> >>>> >> >> >> Here is that output, I don't know if it helps at all to figure out
>> >>> >> >>>> >> >> >> what is wrong.
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >
>> >>> >> >>>> >> >> > That seems to be OK:
>> >>> >> >>>> >> >> >
>> >>> >> >>>> >> >> > (XEN) I/O virtualisation enabled
>> >>> >> >>>> >> >> > (XEN) I/O virtualisation for PV guests disabled
>> >>> >> >>>> >> >> >
>> >>> >> >>>> >> >> > So hmm.. I wonder if it's related to MSI stuff?
>> >>> >> >>>> >> >> > You could try xen.git xen/stable-2.6.32.x branch instead and see if that makes a difference..
>> >>> >> >>>> >> >> >
>> >>> >> >>>> >> >> > -- Pasi
>> >>> >> >>>> >> >> >
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> ---------- Forwarded message ----------
>> >>> >> >>>> >> >> >> From: chris <tknchris@gmail.com>
>> >>> >> >>>> >> >> >> Date: Wed, May 12, 2010 at 5:28 PM
>> >>> >> >>>> >> >> >> Subject: Xen4 / Intel DX58SO Mobo / VT-d not working
>> >>> >> >>>> >> >> >> To: Xen-Users List <xen-users@lists.xensource.com>
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> Hello,
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> I've previously been successful with Xen4 and VT-d on other systems. I
>> >>> >> >>>> >> >> >> am having trouble getting VT-d passthrough working to a WinXP domain
>> >>> >> >>>> >> >> >> with DX58SO (Q45) motherboard and i7 930 CPU. VT-d is enabled in bios,
>> >>> >> >>>> >> >> >> xm info shows hvm_directio capability, I have iommu=1 set, I have the
>> >>> >> >>>> >> >> >> devices bound to pciback on dom0 cmdline, xm
>> >>> >> >>>> >> >> >> pci-list-assignable-devices shows the devices as assignable. When I
>> >>> >> >>>> >> >> >> attempt to start the VM I get the error:
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> Error: Failed to assign device to IOMMU
>> >>> >> >>>> >> >> >> (0000:02:00.0@100,msitranslate=1,power_mgmt=0)
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> Below is all the information I can think of that would be useful to
>> >>> >> >>>> >> >> >> help debug it:
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> BIOS VT-d Enabled:
>> >>> >> >>>> >> >> >> http://i43.tinypic.com/nl3a5e.jpg
>> >>> >> >>>> >> >> >> http://i42.tinypic.com/nqvlu1.jpg
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> grub entry:
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> title Xen 4.0.0 / Debian GNU/Linux, kernel 2.6.31.13
>> >>> >> >>>> >> >> >> root (hd0,0)
>> >>> >> >>>> >> >> >> kernel /boot/xen-4.0.0.gz iommu=1 dom0_mem=256M
>> >>> >> >>>> >> >> >> dom0_max_vcpus=1 dom0_vcpus_pin=true
>> >>> >> >>>> >> >> >> module /boot/vmlinuz-2.6.31.13 root=/dev/md0 ro console=tty0
>> >>> >> >>>> >> >> >> xen-pciback.permissive
>> >>> >> >>>> >> >> >> xen-pciback.hide=(02:00.0)(02:00.1)(02:00.2)(04:00.0)(04:00.1)(04:00.2)(07:00.0)(07:00.1)(07:00.2)(09:00.0)(09:00.1)(09:00.2)
>> >>> >> >>>> >> >> >> module /boot/initrd.img-2.6.31.13
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> # xm pci-list-assignable-devices
>> >>> >> >>>> >> >> >> 0000:09:00.0
>> >>> >> >>>> >> >> >> 0000:09:00.1
>> >>> >> >>>> >> >> >> 0000:09:00.2
>> >>> >> >>>> >> >> >> 0000:07:00.0
>> >>> >> >>>> >> >> >> 0000:07:00.1
>> >>> >> >>>> >> >> >> 0000:07:00.2
>> >>> >> >>>> >> >> >> 0000:04:00.0
>> >>> >> >>>> >> >> >> 0000:04:00.1
>> >>> >> >>>> >> >> >> 0000:04:00.2
>> >>> >> >>>> >> >> >> 0000:02:00.0
>> >>> >> >>>> >> >> >> 0000:02:00.1
>> >>> >> >>>> >> >> >> 0000:02:00.2
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> # xm info
>> >>> >> >>>> >> >> >> host : test-box2
>> >>> >> >>>> >> >> >> release : 2.6.31.13
>> >>> >> >>>> >> >> >> version : #2 SMP Wed May 12 14:11:37 EDT 2010
>> >>> >> >>>> >> >> >> machine : x86_64
>> >>> >> >>>> >> >> >> nr_cpus : 8
>> >>> >> >>>> >> >> >> nr_nodes : 1
>> >>> >> >>>> >> >> >> cores_per_socket : 4
>> >>> >> >>>> >> >> >> threads_per_core : 2
>> >>> >> >>>> >> >> >> cpu_mhz : 2800
>> >>> >> >>>> >> >> >> hw_caps :
>> >>> >> >>>> >> >> >> bfebfbff:28100800:00000000:00001b40:0098e3bd:00000000:00000001:00000000
>> >>> >> >>>> >> >> >> virt_caps : hvm hvm_directio
>> >>> >> >>>> >> >> >> total_memory : 7950
>> >>> >> >>>> >> >> >> free_memory : 7812
>> >>> >> >>>> >> >> >> node_to_cpu : node0:0-7
>> >>> >> >>>> >> >> >> node_to_memory : node0:7812
>> >>> >> >>>> >> >> >> node_to_dma32_mem : node0:3249
>> >>> >> >>>> >> >> >> max_node_id : 0
>> >>> >> >>>> >> >> >> xen_major : 4
>> >>> >> >>>> >> >> >> xen_minor : 0
>> >>> >> >>>> >> >> >> xen_extra : .0
>> >>> >> >>>> >> >> >> xen_caps : xen-3.0-x86_64 xen-3.0-x86_32p hvm-3.0-x86_32
>> >>> >> >>>> >> >> >> hvm-3.0-x86_32p hvm-3.0-x86_64
>> >>> >> >>>> >> >> >> xen_scheduler : credit
>> >>> >> >>>> >> >> >> xen_pagesize : 4096
>> >>> >> >>>> >> >> >> platform_params : virt_start=0xffff800000000000
>> >>> >> >>>> >> >> >> xen_changeset : unavailable
>> >>> >> >>>> >> >> >> xen_commandline : iommu=1 dom0_mem=256M dom0_max_vcpus=1
>> >>> >> >>>> >> >> >> dom0_vcpus_pin=true
>> >>> >> >>>> >> >> >> cc_compiler : gcc version 4.3.2 (Debian 4.3.2-1.1)
>> >>> >> >>>> >> >> >> cc_compile_by : root
>> >>> >> >>>> >> >> >> cc_compile_domain :
>> >>> >> >>>> >> >> >> cc_compile_date : Thu May 6 13:41:25 EDT 2010
>> >>> >> >>>> >> >> >> xend_config_format : 4
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> # xm create vm-five.cfg
>> >>> >> >>>> >> >> >> Using config file "./vm-five.cfg".
>> >>> >> >>>> >> >> >> Error: Failed to assign device to IOMMU
>> >>> >> >>>> >> >> >> (0000:02:00.0@100,msitranslate=1,power_mgmt=0)
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> I feel like I'm missing something really obvious but I've been at it
>> >>> >> >>>> >> >> >> for a while now and have run out of brain power. Anyone have any idea
>> >>> >> >>>> >> >> >> what might be wrong?
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> - chris
>> >>> >> >>>> >> >> >
>> >>> >> >>>> >> >> >> __ __ _ _ ___ ___
>> >>> >> >>>> >> >> >> \ \/ /___ _ __ | || | / _ \ / _ \
>> >>> >> >>>> >> >> >> \ // _ \ \047_ \ | || |_| | | | | | |
>> >>> >> >>>> >> >> >> / \ __/ | | | |__ _| |_| | |_| |
>> >>> >> >>>> >> >> >> /_/\_\___|_| |_| |_|(_)___(_)___/
>> >>> >> >>>> >> >> >>
>> >>> >> >>>> >> >> >> (XEN) Xen version 4.0.0 (root@) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) Thu May 6 13:41:25 EDT 2010
>> >>> >> >>>> >> >> >> (XEN) Latest ChangeSet: unavailable
>> >>> >> >>>> >> >> >> (XEN) Command line: iommu=verbose dom0_mem=256M dom0_max_vcpus=1 dom0_vcpus_pin=true
>> >>> >> >>>> >> >> >> (XEN) Video information:
>> >>> >> >>>> >> >> >> (XEN) VGA is text mode 80x25, font 8x16
>> >>> >> >>>> >> >> >> (XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
>> >>> >> >>>> >> >> >> (XEN) EDID info not retrieved because no DDC retrieval method detected
>> >>> >> >>>> >> >> >> (XEN) Disc information:
>> >>> >> >>>> >> >> >> (XEN) Found 2 MBR signatures
>> >>> >> >>>> >> >> >> (XEN) Found 2 EDD information structures
>> >>> >> >>>> >> >> >> (XEN) Xen-e820 RAM map:
>> >>> >> >>>> >> >> >> (XEN) 0000000000000000 - 000000000008f000 (usable)
>> >>> >> >>>> >> >> >> (XEN) 000000000008f000 - 0000000000090000 (reserved)
>> >>> >> >>>> >> >> >> (XEN) 0000000000090000 - 000000000009ec00 (usable)
>> >>> >> >>>> >> >> >> (XEN) 000000000009ec00 - 00000000000a0000 (reserved)
>> >>> >> >>>> >> >> >> (XEN) 00000000000e0000 - 0000000000100000 (reserved)
>> >>> >> >>>> >> >> >> (XEN) 0000000000100000 - 00000000cf4bd000 (usable)
>> >>> >> >>>> >> >> >> (XEN) 00000000cf4bd000 - 00000000cf4bf000 (reserved)
>> >>> >> >>>> >> >> >> (XEN) 00000000cf4bf000 - 00000000cf4c2000 (usable)
>> >>> >> >>>> >> >> >> (XEN) 00000000cf4c2000 - 00000000cf7bf000 (ACPI NVS)
>> >>> >> >>>> >> >> >> (XEN) 00000000cf7bf000 - 00000000cf7df000 (usable)
>> >>> >> >>>> >> >> >> (XEN) 00000000cf7df000 - 00000000cf7ff000 (ACPI data)
>> >>> >> >>>> >> >> >> (XEN) 00000000cf7ff000 - 00000000cf800000 (usable)
>> >>> >> >>>> >> >> >> (XEN) 00000000cf800000 - 00000000d0000000 (reserved)
>> >>> >> >>>> >> >> >> (XEN) 00000000f8000000 - 00000000fd000000 (reserved)
>> >>> >> >>>> >> >> >> (XEN) 00000000ffe00000 - 0000000100000000 (reserved)
>> >>> >> >>>> >> >> >> (XEN) 0000000100000000 - 0000000230000000 (usable)
>> >>> >> >>>> >> >> >> (XEN) ACPI: RSDP 000FE020, 0024 (r2 INTEL )
>> >>> >> >>>> >> >> >> (XEN) ACPI: XSDT CF7FE120, 0074 (r1 INTEL DX58SO 11F6 1000013)
>> >>> >> >>>> >> >> >> (XEN) ACPI: FACP CF7FD000, 00F4 (r3 INTEL DX58SO 11F6 MSFT 100000D)
>> >>> >> >>>> >> >> >> (XEN) ACPI Warning (tbfadt-0444): Optional field "Pm2ControlBlock" has zero address or length: 0000000000000450/0 [20070126]
>> >>> >> >>>> >> >> >> (XEN) ACPI: DSDT CF7F8000, 4641 (r2 INTEL DX58SO 11F6 MSFT 100000D)
>> >>> >> >>>> >> >> >> (XEN) ACPI: FACS CF728000, 0040
>> >>> >> >>>> >> >> >> (XEN) ACPI: APIC CF7F7000, 0138 (r2 INTEL DX58SO 11F6 MSFT 100000D)
>> >>> >> >>>> >> >> >> (XEN) ACPI: WDDT CF7F6000, 0040 (r1 INTEL DX58SO 11F6 MSFT 100000D)
>> >>> >> >>>> >> >> >> (XEN) ACPI: MCFG CF7F5000, 003C (r1 INTEL DX58SO 11F6 MSFT 100000D)
>> >>> >> >>>> >> >> >> (XEN) ACPI: ASF! CF7F4000, 00AC (r32 INTEL DX58SO 11F6 MSFT 100000D)
>> >>> >> >>>> >> >> >> (XEN) ACPI: HPET CF7F3000, 0038 (r1 INTEL DX58SO 11F6 MSFT 100000D)
>> >>> >> >>>> >> >> >> (XEN) ACPI: SSDT CF7E2000, E134 (r1 INTEL SSDT PM 11F6 MSFT 100000D)
>> >>> >> >>>> >> >> >> (XEN) ACPI: DMAR CF7DF000, 0140 (r1 INTEL DX58SO 11F6 MSFT 100000D)
>> >>> >> >>>> >> >> >> (XEN) ACPI: WDTT CF7F1000, 020C (r2 INTEL DX58SO 11F6 MSFT 100000D)
>> >>> >> >>>> >> >> >> (XEN) ACPI: ASPT CF7F2000, 0034 (r4 INTEL PerfTune 11F6 MSFT 100000D)
>> >>> >> >>>> >> >> >> (XEN) System RAM: 7950MB (8140820kB)
>> >>> >> >>>> >> >> >> (XEN) Domain heap initialised
>> >>> >> >>>> >> >> >> (XEN) Processor #0 7:10 APIC version 21
>> >>> >> >>>> >> >> >> (XEN) Processor #2 7:10 APIC version 21
>> >>> >> >>>> >> >> >> (XEN) Processor #4 7:10 APIC version 21
>> >>> >> >>>> >> >> >> (XEN) Processor #6 7:10 APIC version 21
>> >>> >> >>>> >> >> >> (XEN) Processor #1 7:10 APIC version 21
>> >>> >> >>>> >> >> >> (XEN) Processor #3 7:10 APIC version 21
>> >>> >> >>>> >> >> >> (XEN) Processor #5 7:10 APIC version 21
>> >>> >> >>>> >> >> >> (XEN) Processor #7 7:10 APIC version 21
>> >>> >> >>>> >> >> >> (XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
>> >>> >> >>>> >> >> >> (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:679: Host address width 39
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD:
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:398: dmaru->address = fe711000
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1b.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD:
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:398: dmaru->address = fe710000
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr e9000 end_address e9fff
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ea000 end_address eafff
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr eb000 end_address ebfff
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr e6000 end_address e6fff
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr e7000 end_address e7fff
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr e8000 end_address e8fff
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address eefff
>> >>> >> >>>> >> >> >> (XEN) Using scheduler: SMP Credit Scheduler (credit)
>> >>> >> >>>> >> >> >> (XEN) Detected 2800.125 MHz processor.
>> >>> >> >>>> >> >> >> (XEN) Initing memory sharing.
>> >>> >> >>>> >> >> >> (XEN) VMX: Supported advanced features:
>> >>> >> >>>> >> >> >> (XEN) - APIC MMIO access virtualisation
>> >>> >> >>>> >> >> >> (XEN) - APIC TPR shadow
>> >>> >> >>>> >> >> >> (XEN) - Extended Page Tables (EPT)
>> >>> >> >>>> >> >> >> (XEN) - Virtual-Processor Identifiers (VPID)
>> >>> >> >>>> >> >> >> (XEN) - Virtual NMI
>> >>> >> >>>> >> >> >> (XEN) - MSR direct-access bitmap
>> >>> >> >>>> >> >> >> (XEN) HVM: ASIDs enabled.
>> >>> >> >>>> >> >> >> (XEN) HVM: VMX enabled
>> >>> >> >>>> >> >> >> (XEN) HVM: Hardware Assisted Paging detected.
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1078: drhd->address = fe711000 iommu->reg = ffff82c3fff57000
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1080: cap = c9008010e60262 ecap = f0207a
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1078: drhd->address = fe710000 iommu->reg = ffff82c3fff56000
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f020fa
>> >>> >> >>>> >> >> >> (XEN) Intel VT-d Snoop Control not supported.
>> >>> >> >>>> >> >> >> (XEN) Intel VT-d DMA Passthrough not supported.
>> >>> >> >>>> >> >> >> (XEN) Intel VT-d Queued Invalidation supported.
>> >>> >> >>>> >> >> >> (XEN) Intel VT-d Interrupt Remapping supported.
>> >>> >> >>>> >> >> >> (XEN) I/O virtualisation enabled
>> >>> >> >>>> >> >> >> (XEN) I/O virtualisation for PV guests disabled
>> >>> >> >>>> >> >> >> (XEN) Total of 8 processors activated.
>> >>> >> >>>> >> >> >> (XEN) ENABLING IO-APIC IRQs
>> >>> >> >>>> >> >> >> (XEN) -> Using new ACK method
>> >>> >> >>>> >> >> >> (XEN) TSC is reliable, synchronization unnecessary
>> >>> >> >>>> >> >> >> (XEN) Platform timer is 14.318MHz HPET
>> >>> >> >>>> >> >> >> (XEN) Allocated console ring of 16 KiB.
>> >>> >> >>>> >> >> >> (XEN) Brought up 8 CPUs
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:0.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:10.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:10.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:19.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.5
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 2:0.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 2:0.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 2:0.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 4:0.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 4:0.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 4:0.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 5:0.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 7:0.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 7:0.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 7:0.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 9:0.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 9:0.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 9:0.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = a:0.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.3
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.4
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.5
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.6
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.7
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:0.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:0.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:2.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:2.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:3.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:3.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:3.4
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:4.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:4.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:4.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:4.3
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:5.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:5.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:5.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:5.3
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:6.0
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:6.1
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:6.2
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:6.3
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg = ffff82c3fff57000
>> >>> >> >>>> >> >> >> (XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg = ffff82c3fff56000
>> >>> >> >>>> >> >> >> (XEN) *** LOADING DOMAIN 0 ***
>> >>> >> >>>> >> >> >> (XEN) Xen kernel: 64-bit, lsb, compat32
>> >>> >> >>>> >> >> >> (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26ae000
>> >>> >> >>>> >> >> >> (XEN) PHYSICAL MEMORY ARRANGEMENT:
>> >>> >> >>>> >> >> >> (XEN) Dom0 alloc.: 0000000210000000->0000000220000000
>> >>> >> >>>> >> >> >> (XEN) VIRTUAL MEMORY ARRANGEMENT:
>> >>> >> >>>> >> >> >> (XEN) Loaded kernel: ffffffff81000000->ffffffff826ae000
>> >>> >> >>>> >> >> >> (XEN) Init. ramdisk: ffffffff826ae000->ffffffff8f4de600
>> >>> >> >>>> >> >> >> (XEN) Phys-Mach map: ffffffff8f4df000->ffffffff8f55f000
>> >>> >> >>>> >> >> >> (XEN) Start info: ffffffff8f55f000->ffffffff8f55f4b4
>> >>> >> >>>> >> >> >> (XEN) Page tables: ffffffff8f560000->ffffffff8f5df000
>> >>> >> >>>> >> >> >> (XEN) Boot stack: ffffffff8f5df000->ffffffff8f5e0000
>> >>> >> >>>> >> >> >> (XEN) TOTAL: ffffffff80000000->ffffffff8f800000
>> >>> >> >>>> >> >> >> (XEN) ENTRY ADDRESS: ffffffff81a10860
>> >>> >> >>>> >> >> >> (XEN) Dom0 has maximum 1 VCPUs
>> >>> >> >>>> >> >> >> (XEN) Scrubbing Free RAM: ..............................................................................done.
>> >>> >> >>>> >> >> >> (XEN) Xen trace buffers: disabled
>> >>> >> >>>> >> >> >> (XEN) Std. Loglevel: Errors and warnings
>> >>> >> >>>> >> >> >> (XEN) Guest Loglevel: Nothing (Rate-limited: Errors and warnings)
>> >>> >> >>>> >> >> >> (XEN) Xen is relinquishing VGA console.
>> >>> >> >>>> >> >> >> (XEN) *** Serial input -> DOM0 (type \047CTRL-a\047 three times to switch input to Xen)
>> >>> >> >>>> >> >> >> (XEN) Freed 164kB init memory.
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: apic=0, pin=0, irq=0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: new_entry=000109f0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: old_entry=00010000 pirq=0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: apic=0, pin=2, irq=0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: new_entry=000109f0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: old_entry=000009f0 pirq=0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> >>> >> >>>> >> >> >> (XEN) irq.c:1445: dom0: pirq 0 or irq 3 already mapped
>> >>> >> >>>> >> >> >> (XEN) irq.c:1445: dom0: pirq 0 or irq 4 already mapped
>> >>> >> >>>> >> >> >> (XEN) irq.c:1445: dom0: pirq 0 or irq 5 already mapped
>> >>> >> >>>> >> >> >> (XEN) irq.c:1445: dom0: pirq 0 or irq 6 already mapped
>> >>> >> >>>> >> >> >> (XEN) irq.c:1445: dom0: pirq 0 or irq 7 already mapped
>> >>> >> >>>> >> >> >> (XEN) irq.c:1445: dom0: pirq 0 or irq 8 already mapped
>> >>> >> >>>> >> >> >> (XEN) irq.c:1445: dom0: pirq 0 or irq 9 already mapped
>> >>> >> >>>> >> >> >> (XEN) irq.c:1445: dom0: pirq 0 or irq 10 already mapped
>> >>> >> >>>> >> >> >> (XEN) irq.c:1445: dom0: pirq 0 or irq 11 already mapped
>> >>> >> >>>> >> >> >> (XEN) irq.c:1445: dom0: pirq 0 or irq 12 already mapped
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: apic=0, pin=0, irq=0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: new_entry=000009f0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: old_entry=00010000 pirq=0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: apic=0, pin=18, irq=18
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: new_entry=0001a9c0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: old_entry=0000a9c0 pirq=18
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: apic=0, pin=19, irq=19
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: new_entry=0001a9c8
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: old_entry=0000a9c8 pirq=19
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: apic=0, pin=23, irq=23
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: new_entry=0001a929
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: old_entry=0000a929 pirq=23
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: apic=0, pin=19, irq=19
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: new_entry=0001a9c8
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: old_entry=0000a9c8 pirq=19
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: apic=0, pin=18, irq=18
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: new_entry=0001a9c0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: old_entry=0000a9c0 pirq=18
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: apic=0, pin=16, irq=16
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: new_entry=0001a9b0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: old_entry=0000a9b0 pirq=16
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: apic=0, pin=16, irq=16
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: new_entry=0001a9b0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: old_entry=0000a9b0 pirq=16
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: apic=0, pin=19, irq=19
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: new_entry=0001a9c8
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: old_entry=0000a9c8 pirq=19
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: apic=0, pin=18, irq=18
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: new_entry=0001a9c0
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: old_entry=0000a9c0 pirq=18
>> >>> >> >>>> >> >> >> (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
>> >>> >> >>>> >> >> >
>> >>> >> >>>> >> >> >> _______________________________________________
>> >>> >> >>>> >> >> >> Xen-users mailing list
>> >>> >> >>>> >> >> >> Xen-users@lists.xensource.com
>> >>> >> >>>> >> >> >> http://lists.xensource.com/xen-users
>> >>> >> >>>> >> >> >
>> >>> >> >>>> >> >
>> >>> >> >>>> >
>> >>> >> >>>
>> >>> >> >>
>> >>> >> >
>> >>> >
>> >>
>> >
>
[-- Attachment #2: WORKING.txt --]
[-- Type: text/plain, Size: 64902 bytes --]
scanmaster1:~# uname -a
Linux scanmaster1 2.6.31.6 #1 SMP Wed Dec 23 16:20:35 EST 2009 x86_64 GNU/Linux
scanmaster1:~# xm info
host : scanmaster1
release : 2.6.31.6
version : #1 SMP Wed Dec 23 16:20:35 EST 2009
machine : x86_64
nr_cpus : 4
nr_nodes : 1
cores_per_socket : 4
threads_per_core : 1
cpu_mhz : 2660
hw_caps : bfebfbff:20100800:00000000:00000140:0408e3fd:00000000:00000001:00000000
virt_caps : hvm hvm_directio
total_memory : 4016
free_memory : 63
node_to_cpu : node0:0-3
node_to_memory : node0:63
xen_major : 3
xen_minor : 4
xen_extra : .2
xen_caps : xen-3.0-x86_64 xen-3.0-x86_32p hvm-3.0-x86_32 hvm-3.0-x86_32p hvm-3.0-x86_64
xen_scheduler : credit
xen_pagesize : 4096
platform_params : virt_start=0xffff800000000000
xen_changeset : unavailable
cc_compiler : gcc version 4.3.2 (Debian 4.3.2-1.1)
cc_compile_by : root
cc_compile_domain :
cc_compile_date : Wed Dec 23 15:58:58 EST 2009
xend_config_format : 4
__ __ _____ _ _ ____
\ \/ /___ _ __ |___ /| || | |___ \
\ // _ \ '_ \ |_ \| || |_ __) |
/ \ __/ | | | ___) |__ _| / __/
/_/\_\___|_| |_| |____(_) |_|(_)_____|
(XEN) Xen version 3.4.2 (root@) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) Wed Dec 23 15:58:58 EST 2009
(XEN) Latest ChangeSet: unavailable
(XEN) Command line: vtd=1 iommu=1 dom0_mem=768M dom0_max_vcpus=1 dom0_vcpus_pin=true
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 2 MBR signatures
(XEN) Found 2 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000008f000 (usable)
(XEN) 000000000008f000 - 0000000000090000 (reserved)
(XEN) 0000000000090000 - 000000000009dc00 (usable)
(XEN) 000000000009dc00 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000cde36000 (usable)
(XEN) 00000000cde36000 - 00000000cdeb7000 (ACPI NVS)
(XEN) 00000000cdeb7000 - 00000000cf02a000 (usable)
(XEN) 00000000cf02a000 - 00000000cf02c000 (reserved)
(XEN) 00000000cf02c000 - 00000000cf156000 (usable)
(XEN) 00000000cf156000 - 00000000cf1e3000 (ACPI NVS)
(XEN) 00000000cf1e3000 - 00000000cf1eb000 (usable)
(XEN) 00000000cf1eb000 - 00000000cf1f3000 (ACPI data)
(XEN) 00000000cf1f3000 - 00000000cf1f4000 (usable)
(XEN) 00000000cf1f4000 - 00000000cf1ff000 (ACPI data)
(XEN) 00000000cf1ff000 - 00000000cf200000 (usable)
(XEN) 00000000cf200000 - 00000000d0000000 (reserved)
(XEN) 00000000f0000000 - 00000000f8000000 (reserved)
(XEN) 00000000ffc00000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000012c000000 (usable)
(XEN) System RAM: 4016MB (4112868kB)
(XEN) ACPI: RSDP 000FE020, 0014 (r0 INTEL )
(XEN) ACPI: RSDT CF1FD038, 005C (r1 INTEL DQ3510J 466 1000013)
(XEN) ACPI: FACP CF1FC000, 0074 (r1 INTEL DQ3510J 466 MSFT 1000013)
(XEN) ACPI: DSDT CF1F8000, 3D6A (r1 INTEL DQ3510J 466 MSFT 1000013)
(XEN) ACPI: FACS CF163000, 0040
(XEN) ACPI: APIC CF1F7000, 0078 (r1 INTEL DQ3510J 466 MSFT 1000013)
(XEN) ACPI: WDDT CF1F6000, 0040 (r1 INTEL DQ3510J 466 MSFT 1000013)
(XEN) ACPI: MCFG CF1F5000, 003C (r1 INTEL DQ3510J 466 MSFT 1000013)
(XEN) ACPI: ASF! CF1F4000, 00A6 (r32 INTEL DQ3510J 466 MSFT 1000013)
(XEN) ACPI: DMAR CF1F2000, 0120 (r1 INTEL DQ3510J 466 MSFT 1000013)
(XEN) ACPI: ASPT CF1F1000, 0034 (r3 INTEL DQ3510J 466 MSFT 1000013)
(XEN) ACPI: WDTT CF1F0000, 02CC (r1 INTEL DQ3510J 466 MSFT 1000013)
(XEN) ACPI: SSDT CF1EF000, 0204 (r1 INTEL CpuPm 466 MSFT 1000013)
(XEN) ACPI: SSDT CF1EE000, 00DD (r1 INTEL Cpu0Cst 466 MSFT 1000013)
(XEN) ACPI: SSDT CF1ED000, 00DD (r1 INTEL Cpu1Cst 466 MSFT 1000013)
(XEN) ACPI: SSDT CF1EC000, 00DD (r1 INTEL Cpu2Cst 466 MSFT 1000013)
(XEN) ACPI: SSDT CF1EB000, 00DD (r1 INTEL Cpu3Cst 466 MSFT 1000013)
(XEN) ACPI: TCPA CF157000, 0032 (r2 INTEL TIANO 2 MSFT 1000013)
(XEN) Domain heap initialised
(XEN) Processor #0 7:7 APIC version 20
(XEN) Processor #2 7:7 APIC version 20
(XEN) Processor #1 7:7 APIC version 20
(XEN) Processor #3 7:7 APIC version 20
(XEN) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) Intel VT-d DMAR tables have been parsed.
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 2660.038 MHz processor.
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9400 @ 2.66GHz stepping 0a
(XEN) Booting processor 1/2 eip 8c000
(XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9400 @ 2.66GHz stepping 0a
(XEN) Booting processor 2/1 eip 8c000
(XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9400 @ 2.66GHz stepping 0a
(XEN) Booting processor 3/3 eip 8c000
(XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9400 @ 2.66GHz stepping 0a
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) checking TSC synchronization across 4 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
(XEN) Brought up 4 CPUs
(XEN) Intel VT-d Snoop Control not supported.
(XEN) Intel VT-d DMA Passthrough not supported.
(XEN) Intel VT-d Queued Invalidation not supported.
(XEN) Intel VT-d Interrupt Remapping not supported.
(XEN) I/O virtualisation enabled
(XEN) I/O virtualisation for PV guests disabled
(XEN) CPUIDLE: disabled due to no HPET. Force enable with 'cpuidle'.
(XEN) [VT-D]iommu.c:721: iommu_page_fault: iommu->reg = ffff828bfff56000
(XEN) [VT-D]iommu.c:690: iommu_fault_status: Fault Overflow
(XEN) [VT-D]iommu.c:693: iommu_fault_status: Primary Pending Fault
(XEN) [VT-D]iommu.c:675: iommu_fault:DMA Write: 0:2.0 addr 280002000 REASON 5 iommu->reg = ffff828bfff56000
(XEN) print_vtd_entries: iommu = ffff83012bde4590 bdf = 0:2:0 gmfn = 280002
(XEN) root_entry = ffff83012bdad000
(XEN) root_entry[0] = 12822f001
(XEN) context = ffff83012822f000
(XEN) context[10] = 101_12bd8f001
(XEN) l3 = ffff83012bd8f000
(XEN) l3_index = a
(XEN) l3[a] = 0
(XEN) l3[a] not present
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x26a5000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000110000000->0000000120000000 (131072 pages to be allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff81000000->ffffffff826a5000
(XEN) Init. ramdisk: ffffffff826a5000->ffffffff8f501a00
(XEN) Phys-Mach map: ffffffff8f502000->ffffffff8f682000
(XEN) Start info: ffffffff8f682000->ffffffff8f6824b4
(XEN) Page tables: ffffffff8f683000->ffffffff8f702000
(XEN) Boot stack: ffffffff8f702000->ffffffff8f703000
(XEN) TOTAL: ffffffff80000000->ffffffff8f800000
(XEN) ENTRY ADDRESS: ffffffff81a08860
(XEN) Dom0 has maximum 1 VCPUs
(XEN) Scrubbing Free RAM: ...............................done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: Errors and warnings
(XEN) Guest Loglevel: Nothing (Rate-limited: Errors and warnings)
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen)
(XEN) Freed 136kB init memory.
(XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
(XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900
(XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=0, old_irq=-1, new_irq=0
(XEN) ioapic_guest_write: old_entry=00010900, new_entry=000009f0
(XEN) ioapic_guest_write: Attempt to add IO-APIC pin for in-use IRQ!
(XEN) mm.c:806:d0 Error getting mfn 30000 (pfn 5555555555555555) from L1 entry 8000000030000473 for l1e_owner=0, pg_owner=32753
(XEN) ioapic_guest_write: apic=0, pin=17, old_irq=17, new_irq=17
(XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23
(XEN) ioapic_guest_write: old_entry=0000a951, new_entry=0001a951
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
(XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
(XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
(XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
(XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.31.6 (root@scanmaster1) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 SMP Wed Dec 23 16:20:35 EST 2009
Command line: root=/dev/md0 ro console=tty0 xen-pciback.permissive xen-pciback.hide=(02:00.0)(02:00.1)(02:00.2)(04:00.0)(04:00.1)(04:00.2)(06:00.0)(06:00.1)(06:00.2)(0a:00.0)(0a
:00.1)(0a:00.2)(0a:03.0)
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
xen_release_chunk: looking at area pfn 30000-cde36
xen_release_chunk: looking at area pfn cdeb7-cf02a
xen_release_chunk: looking at area pfn cf02c-cf156
xen_release_chunk: looking at area pfn cf1e3-cf1eb
xen_release_chunk: looking at area pfn cf1f3-cf1f4
xen_release_chunk: looking at area pfn cf1ff-cf200
xen_release_chunk: looking at area pfn d0000-f0000
xen_release_chunk: looking at area pfn f8000-ffc00
released 0 pages of unused memory
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 000000000008f000 (usable)
Xen: 000000000008f000 - 0000000000090000 (reserved)
Xen: 0000000000090000 - 000000000009dc00 (usable)
Xen: 000000000009dc00 - 0000000000100000 (reserved)
Xen: 0000000000100000 - 0000000030000000 (usable)
Xen: 00000000cde36000 - 00000000cdeb7000 (ACPI NVS)
Xen: 00000000cf02a000 - 00000000cf02c000 (reserved)
Xen: 00000000cf156000 - 00000000cf1e3000 (ACPI NVS)
Xen: 00000000cf1eb000 - 00000000cf1f3000 (ACPI data)
Xen: 00000000cf1f4000 - 00000000cf1ff000 (ACPI data)
Xen: 00000000cf200000 - 00000000d0000000 (reserved)
Xen: 00000000f0000000 - 00000000f8000000 (reserved)
Xen: 00000000ffc00000 - 0000000100000000 (reserved)
DMI 2.4 present.
last_pfn = 0x30000 max_arch_pfn = 0x400000000
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-0000000030000000
0000000000 - 0030000000 page 4k
kernel direct mapping tables up to 30000000 @ 100000-282000
RAMDISK: 026a5000 - 0f501a00
ACPI: RSDP 00000000000fe020 00014 (v00 INTEL )
ACPI: RSDT 00000000cf1fd038 0005C (v01 INTEL DQ3510J 00000466 01000013)
ACPI: FACP 00000000cf1fc000 00074 (v01 INTEL DQ3510J 00000466 MSFT 01000013)
ACPI: DSDT 00000000cf1f8000 03D6A (v01 INTEL DQ3510J 00000466 MSFT 01000013)
ACPI: FACS 00000000cf163000 00040
ACPI: APIC 00000000cf1f7000 00078 (v01 INTEL DQ3510J 00000466 MSFT 01000013)
ACPI: WDDT 00000000cf1f6000 00040 (v01 INTEL DQ3510J 00000466 MSFT 01000013)
ACPI: MCFG 00000000cf1f5000 0003C (v01 INTEL DQ3510J 00000466 MSFT 01000013)
ACPI: ASF! 00000000cf1f4000 000A6 (v32 INTEL DQ3510J 00000466 MSFT 01000013)
ACPI: 00000000cf1f2000 00120 (v01 INTEL DQ3510J 00000466 MSFT 01000013)
ACPI: ASPT 00000000cf1f1000 00034 (v03 INTEL DQ3510J 00000466 MSFT 01000013)
ACPI: WDTT 00000000cf1f0000 002CC (v01 INTEL DQ3510J 00000466 MSFT 01000013)
ACPI: SSDT 00000000cf1ef000 00204 (v01 INTEL CpuPm 00000466 MSFT 01000013)
ACPI: SSDT 00000000cf1ee000 000DD (v01 INTEL Cpu0Cst 00000466 MSFT 01000013)
ACPI: SSDT 00000000cf1ed000 000DD (v01 INTEL Cpu1Cst 00000466 MSFT 01000013)
ACPI: SSDT 00000000cf1ec000 000DD (v01 INTEL Cpu2Cst 00000466 MSFT 01000013)
ACPI: SSDT 00000000cf1eb000 000DD (v01 INTEL Cpu3Cst 00000466 MSFT 01000013)
ACPI: TCPA 00000000cf157000 00032 (v02 INTEL TIANO 00000002 MSFT 01000013)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-0000000030000000
Bootmem setup node 0 0000000000000000-0000000030000000
NODE_DATA [0000000000008000 - 000000000001ffff]
bootmap [0000000000020000 - 0000000000025fff] pages 6
(8 early reservations) ==> bootmem [0000000000 - 0030000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [000f683000 - 000f702000] XEN PAGETABLES ==> [000f683000 - 000f702000]
#2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#3 [0001000000 - 0002684090] TEXT DATA BSS ==> [0001000000 - 0002684090]
#4 [00026a5000 - 000f501a00] RAMDISK ==> [00026a5000 - 000f501a00]
#5 [000f502000 - 000f683000] XEN START INFO ==> [000f502000 - 000f683000]
#6 [0002685000 - 00026851a6] BRK ==> [0002685000 - 00026851a6]
#7 [0000100000 - 0000200000] PGTABLE ==> [0000100000 - 0000200000]
found SMP MP-table at [ffff8800000fe5c0] fe5c0
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000000 -> 0x0000008f
0: 0x00000090 -> 0x0000009d
0: 0x00000100 -> 0x00030000
On node 0 totalpages: 196508
DMA zone: 104 pages used for memmap
DMA zone: 259 pages reserved
DMA zone: 3633 pages, LIFO batch:0
DMA32 zone: 4888 pages used for memmap
DMA32 zone: 187624 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 1 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000008f000 - 0000000000090000
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 0000000000100000
Allocating PCI resources starting at 30000000 (gap: 30000000:9de36000)
NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:1 nr_node_ids:1
PERCPU: Allocated 471 4k pages, static data 1926752 bytes
trying to map vcpu_info 0 at ffffc9000000b020, mfn 11f727, offset 32
cpu 0 using vcpu_info at ffffc9000000b020
Xen: using vcpu_info placement
Built 1 zonelists in Node order, mobility grouping on. Total pages: 191257
Policy zone: DMA32
Kernel command line: root=/dev/md0 ro console=tty0 xen-pciback.permissive xen-pciback.hide=(02:00.0)(02:00.1)(02:00.2)(04:00.0)(04:00.1)(04:00.2)(06:00.0)(06:00.1)(06:00.2)(0a:0
0.0)(0a:00.1)(0a:00.2)(0a:03.0)
PID hash table entries: 4096 (order: 12, 32768 bytes)
Initializing CPU#0
PCI-DMA: Using Xen software bounce buffering for IO (Xen-SWIOTLB)
xen_swiotlb_fixup: buf=ffff880010e8f000 size=67108864
xen_swiotlb_fixup: buf=ffff880014eef000 size=32768
Placing 64MB Xen software IO TLB between ffff880010e8f000 - ffff880014e8f000
Xen software IO TLB at phys 0x10e8f000 - 0x14e8f000
Memory: 460440k/786432k available (5257k kernel code, 400k absent, 325592k reserved, 3127k data, 3208k init)
SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:4352 nr_irqs:256
xen: registering gsi 0 triggering 1 polarity 0
xen: --> irq=0
xen_set_ioapic_routing: irq 0 gsi 0 vector 240 ioapic 0 pin 0 triggering 0 polarity 0
xen: registering gsi 1 triggering 1 polarity 0
xen: --> irq=1
xen_set_ioapic_routing: irq 1 gsi 1 vector 32 ioapic 0 pin 1 triggering 0 polarity 0
xen: registering gsi 3 triggering 1 polarity 0
xen: --> irq=3
xen_set_ioapic_routing: irq 3 gsi 3 vector 40 ioapic 0 pin 3 triggering 0 polarity 0
xen: registering gsi 4 triggering 1 polarity 0
xen: --> irq=4
xen_set_ioapic_routing: irq 4 gsi 4 vector 48 ioapic 0 pin 4 triggering 0 polarity 0
xen: registering gsi 5 triggering 1 polarity 0
xen: --> irq=5
xen_set_ioapic_routing: irq 5 gsi 5 vector 56 ioapic 0 pin 5 triggering 0 polarity 0
xen: registering gsi 6 triggering 1 polarity 0
xen: --> irq=6
xen_set_ioapic_routing: irq 6 gsi 6 vector 64 ioapic 0 pin 6 triggering 0 polarity 0
xen: registering gsi 7 triggering 1 polarity 0
xen: --> irq=7
xen_set_ioapic_routing: irq 7 gsi 7 vector 72 ioapic 0 pin 7 triggering 0 polarity 0
xen: registering gsi 8 triggering 1 polarity 0
xen: --> irq=8
xen_set_ioapic_routing: irq 8 gsi 8 vector 80 ioapic 0 pin 8 triggering 0 polarity 0
xen: registering gsi 9 triggering 0 polarity 0
xen: --> irq=9
xen_set_ioapic_routing: irq 9 gsi 9 vector 88 ioapic 0 pin 9 triggering 1 polarity 0
xen: registering gsi 10 triggering 1 polarity 0
xen: --> irq=10
xen_set_ioapic_routing: irq 10 gsi 10 vector 96 ioapic 0 pin 10 triggering 0 polarity 0
xen: registering gsi 11 triggering 1 polarity 0
xen: --> irq=11
xen_set_ioapic_routing: irq 11 gsi 11 vector 104 ioapic 0 pin 11 triggering 0 polarity 0
xen: registering gsi 12 triggering 1 polarity 0
xen: --> irq=12
xen_set_ioapic_routing: irq 12 gsi 12 vector 112 ioapic 0 pin 12 triggering 0 polarity 0
xen: registering gsi 13 triggering 1 polarity 0
xen: --> irq=13
xen_set_ioapic_routing: irq 13 gsi 13 vector 120 ioapic 0 pin 13 triggering 0 polarity 0
xen: registering gsi 14 triggering 1 polarity 0
xen: --> irq=14
xen_set_ioapic_routing: irq 14 gsi 14 vector 136 ioapic 0 pin 14 triggering 0 polarity 0
xen: registering gsi 15 triggering 1 polarity 0
xen: --> irq=15
xen_set_ioapic_routing: irq 15 gsi 15 vector 144 ioapic 0 pin 15 triggering 0 polarity 0
Detected 2660.002 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES: 8
... MAX_LOCK_DEPTH: 48
... MAX_LOCKDEP_KEYS: 8191
... CLASSHASH_SIZE: 4096
... MAX_LOCKDEP_ENTRIES: 16384
... MAX_LOCKDEP_CHAINS: 32768
... CHAINHASH_SIZE: 16384
memory used by lock dependency info: 6207 kB
per task-struct memory footprint: 2688 bytes
allocated 7864320 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
ODEBUG: 9 of 9 active objects replaced
Xen: using vcpuop timer interface
installing Xen timer for CPU 0
alloc irq_desc for 255 on node 0
alloc kstat_irqs on node 0
xen: vcpu_time_info placement not supported
Calibrating delay loop (skipped), value calculated using timer frequency.. 5320.00 BogoMIPS (lpj=2660002)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 3072K
CPU 0/0x0 -> Node 0
CPU: Unsupported number of siblings 4
mce: CPU supports 6 MCE banks
Performance Counters: unsupported p6 CPU model 23 no PMU driver, software counters only.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 31k freed
ACPI: Core revision 20090521
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 20187 entries in 80 pages
alloc irq_desc for 254 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 253 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 252 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 251 on node 0
alloc kstat_irqs on node 0
Brought up 1 CPUs
CPU0 attaching NULL sched-domain.
Booting paravirtualized kernel on Xen
Xen version: 3.4.2 (preserve-AD) (dom0)
Grant tables using version 1 layout.
Grant table initialized
regulator: core version 0.5
Time: 12:08:39 Date: 05/11/10
NET: Registered protocol family 16
alloc irq_desc for 250 on node 0
alloc kstat_irqs on node 0
xenbus_probe_init ok
ACPI: bus type pci registered
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 127
PCI: MCFG area at f0000000 reserved in E820
PCI: Using MMCONFIG at f0000000 - f7ffffff
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI Warning: Incorrect checksum in table [ ] - A8, should be EC 20090521 tbutils-246
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:02.0: reg 10 32bit mmio: [0xe0680000-0xe06fffff]
pci 0000:00:02.0: reg 14 io port: [0x2430-0x2437]
pci 0000:00:02.0: reg 18 32bit mmio: [0xd0000000-0xdfffffff]
pci 0000:00:02.0: reg 1c 32bit mmio: [0xe0400000-0xe04fffff]
pci 0000:00:02.1: reg 10 32bit mmio: [0xe0600000-0xe067ffff]
pci 0000:00:03.0: reg 10 64bit mmio: [0xe0726100-0xe072610f]
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:19.0: reg 10 32bit mmio: [0xe0700000-0xe071ffff]
pci 0000:00:19.0: reg 14 32bit mmio: [0xe0724000-0xe0724fff]
pci 0000:00:19.0: reg 18 io port: [0x2400-0x241f]
pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
pci 0000:00:19.0: PME# disabled
pci 0000:00:1a.0: reg 20 io port: [0x20e0-0x20ff]
pci 0000:00:1a.1: reg 20 io port: [0x20c0-0x20df]
pci 0000:00:1a.2: reg 20 io port: [0x20a0-0x20bf]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xe0725c00-0xe0725fff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xe0720000-0xe0723fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0x2080-0x209f]
pci 0000:00:1d.1: reg 20 io port: [0x2060-0x207f]
pci 0000:00:1d.2: reg 20 io port: [0x2040-0x205f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xe0725800-0xe0725bff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
pci 0000:00:1f.2: reg 10 io port: [0x2428-0x242f]
pci 0000:00:1f.2: reg 14 io port: [0x243c-0x243f]
pci 0000:00:1f.2: reg 18 io port: [0x2420-0x2427]
pci 0000:00:1f.2: reg 1c io port: [0x2438-0x243b]
pci 0000:00:1f.2: reg 20 io port: [0x2020-0x203f]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xe0725000-0xe07257ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 64bit mmio: [0xe0726000-0xe07260ff]
pci 0000:00:1f.3: reg 20 io port: [0x2000-0x201f]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
pci 0000:00:01.0: bridge 32bit mmio: [0xe0500000-0xe05fffff]
pci 0000:02:00.0: reg 10 32bit mmio: [0xe0501000-0xe0501fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:02:00.0: PME# disabled
pci 0000:02:00.1: reg 10 32bit mmio: [0xe0500000-0xe0500fff]
pci 0000:02:00.1: supports D1 D2
pci 0000:02:00.1: PME# supported from D0 D1 D2 D3hot
pci 0000:02:00.1: PME# disabled
pci 0000:02:00.2: reg 10 32bit mmio: [0xe0502000-0xe05020ff]
pci 0000:02:00.2: supports D1 D2
pci 0000:02:00.2: PME# supported from D0 D1 D2 D3hot
pci 0000:02:00.2: PME# disabled
pci 0000:01:00.0: bridge 32bit mmio: [0xe0500000-0xe05fffff]
pci 0000:03:00.0: supports D1 D2
pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
pci 0000:00:1c.0: bridge 32bit mmio: [0xe0300000-0xe03fffff]
pci 0000:04:00.0: reg 10 32bit mmio: [0xe0301000-0xe0301fff]
pci 0000:04:00.0: supports D1 D2
pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:04:00.0: PME# disabled
pci 0000:04:00.1: reg 10 32bit mmio: [0xe0300000-0xe0300fff]
pci 0000:04:00.1: supports D1 D2
pci 0000:04:00.1: PME# supported from D0 D1 D2 D3hot
pci 0000:04:00.1: PME# disabled
pci 0000:04:00.2: reg 10 32bit mmio: [0xe0302000-0xe03020ff]
pci 0000:04:00.2: supports D1 D2
pci 0000:04:00.2: PME# supported from D0 D1 D2 D3hot
pci 0000:04:00.2: PME# disabled
pci 0000:03:00.0: bridge 32bit mmio: [0xe0300000-0xe03fffff]
pci 0000:05:00.0: supports D1 D2
pci 0000:05:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
pci 0000:00:1c.1: bridge 32bit mmio: [0xe0200000-0xe02fffff]
pci 0000:06:00.0: reg 10 32bit mmio: [0xe0201000-0xe0201fff]
pci 0000:06:00.0: supports D1 D2
pci 0000:06:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:06:00.0: PME# disabled
pci 0000:06:00.1: reg 10 32bit mmio: [0xe0200000-0xe0200fff]
pci 0000:06:00.1: supports D1 D2
pci 0000:06:00.1: PME# supported from D0 D1 D2 D3hot
pci 0000:06:00.1: PME# disabled
pci 0000:06:00.2: reg 10 32bit mmio: [0xe0202000-0xe02020ff]
pci 0000:06:00.2: supports D1 D2
pci 0000:06:00.2: PME# supported from D0 D1 D2 D3hot
pci 0000:06:00.2: PME# disabled
pci 0000:05:00.0: bridge 32bit mmio: [0xe0200000-0xe02fffff]
pci 0000:07:00.0: reg 10 io port: [0x1018-0x101f]
pci 0000:07:00.0: reg 14 io port: [0x1024-0x1027]
pci 0000:07:00.0: reg 18 io port: [0x1010-0x1017]
pci 0000:07:00.0: reg 1c io port: [0x1020-0x1023]
pci 0000:07:00.0: reg 20 io port: [0x1000-0x100f]
pci 0000:07:00.0: reg 24 32bit mmio: [0xe0100000-0xe01001ff]
pci 0000:07:00.0: supports D1
pci 0000:07:00.0: PME# supported from D0 D1 D3hot
pci 0000:07:00.0: PME# disabled
pci 0000:07:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
pci 0000:00:1c.2: bridge io port: [0x1000-0x1fff]
pci 0000:00:1c.2: bridge 32bit mmio: [0xe0100000-0xe01fffff]
pci 0000:0a:00.0: reg 10 32bit mmio: [0xe0002000-0xe0002fff]
pci 0000:0a:00.0: supports D1 D2
pci 0000:0a:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:0a:00.0: PME# disabled
pci 0000:0a:00.1: reg 10 32bit mmio: [0xe0001000-0xe0001fff]
pci 0000:0a:00.1: supports D1 D2
pci 0000:0a:00.1: PME# supported from D0 D1 D2 D3hot
pci 0000:0a:00.1: PME# disabled
pci 0000:0a:00.2: reg 10 32bit mmio: [0xe0003000-0xe00030ff]
pci 0000:0a:00.2: supports D1 D2
pci 0000:0a:00.2: PME# supported from D0 D1 D2 D3hot
pci 0000:0a:00.2: PME# disabled
pci 0000:0a:03.0: reg 10 32bit mmio: [0xe0000000-0xe0000fff]
pci 0000:0a:03.0: supports D1 D2
pci 0000:0a:03.0: PME# supported from D0 D1 D2 D3hot
pci 0000:0a:03.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xe0000000-0xe00fffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
sync cpu 0 get result ffffffff max_id 0
Failed to sync pcpu 0
xenbus_probe_backend_init bus registered ok
xen_balloon: Initialising balloon driver with page order 0.
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
IO APIC resources couldn't be allocated.
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
DMA-API: preallocated 32768 debug entries
DMA-API: debugging enabled by kernel config
Switched to high resolution mode on CPU 0
pnp: PnP ACPI init
ACPI: bus type pnp registered
xen: registering gsi 8 triggering 1 polarity 0
xen_allocate_pirq: returning irq 8 for gsi 8
xen: --> irq=8
xen_set_ioapic_routing: irq 8 gsi 8 vector 80 ioapic 0 pin 8 triggering 0 polarity 0
xen: registering gsi 13 triggering 1 polarity 0
xen_allocate_pirq: returning irq 13 for gsi 13
xen: --> irq=13
xen_set_ioapic_routing: irq 13 gsi 13 vector 120 ioapic 0 pin 13 triggering 0 polarity 0
xen: registering gsi 4 triggering 1 polarity 0
xen_allocate_pirq: returning irq 4 for gsi 4
xen: --> irq=4
xen_set_ioapic_routing: irq 4 gsi 4 vector 48 ioapic 0 pin 4 triggering 0 polarity 0
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xf0000000-0xf7ffffff has been reserved
system 00:01: iomem range 0xfeb00000-0xfeb03fff has been reserved
system 00:01: iomem range 0xfed13000-0xfed13fff has been reserved
system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:01: iomem range 0xfed45000-0xfed99fff has been reserved
system 00:01: iomem range 0xc0000-0xdffff could not be reserved
system 00:01: iomem range 0xe0000-0xfffff could not be reserved
system 00:01: iomem range 0xffc00000-0xffffffff has been reserved
system 00:06: ioport range 0x500-0x53f has been reserved
system 00:06: ioport range 0x400-0x47f has been reserved
system 00:06: ioport range 0x680-0x6ff has been reserved
work_for_cpu used greatest stack depth: 6624 bytes left
work_for_cpu used greatest stack depth: 6416 bytes left
pciback 0000:02:00.0: seizing device
work_for_cpu used greatest stack depth: 6376 bytes left
pciback 0000:02:00.1: seizing device
pciback 0000:02:00.2: seizing device
pciback 0000:04:00.0: seizing device
pciback 0000:04:00.1: seizing device
pciback 0000:04:00.2: seizing device
pciback 0000:06:00.0: seizing device
pciback 0000:06:00.1: seizing device
pciback 0000:06:00.2: seizing device
pciback 0000:0a:00.0: seizing device
pciback 0000:0a:00.1: seizing device
pciback 0000:0a:00.2: seizing device
pciback 0000:0a:03.0: seizing device
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0xe0500000-0xe05fffff
pci 0000:01:00.0: PREFETCH window: disabled
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: disabled
pci 0000:00:01.0: MEM window: 0xe0500000-0xe05fffff
pci 0000:00:01.0: PREFETCH window: disabled
pci 0000:03:00.0: PCI bridge, secondary bus 0000:04
pci 0000:03:00.0: IO window: disabled
pci 0000:03:00.0: MEM window: 0xe0300000-0xe03fffff
pci 0000:03:00.0: PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.0: IO window: disabled
pci 0000:00:1c.0: MEM window: 0xe0300000-0xe03fffff
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:05:00.0: PCI bridge, secondary bus 0000:06
pci 0000:05:00.0: IO window: disabled
pci 0000:05:00.0: MEM window: 0xe0200000-0xe02fffff
pci 0000:05:00.0: PREFETCH window: disabled
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:05
pci 0000:00:1c.1: IO window: disabled
pci 0000:00:1c.1: MEM window: 0xe0200000-0xe02fffff
pci 0000:00:1c.1: PREFETCH window: disabled
pci 0000:00:1c.2: PCI bridge, secondary bus 0000:07
pci 0000:00:1c.2: IO window: 0x1000-0x1fff
pci 0000:00:1c.2: MEM window: 0xe0100000-0xe01fffff
pci 0000:00:1c.2: PREFETCH window: disabled
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:08
pci 0000:00:1c.3: IO window: disabled
pci 0000:00:1c.3: MEM window: disabled
pci 0000:00:1c.3: PREFETCH window: disabled
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:09
pci 0000:00:1c.4: IO window: disabled
pci 0000:00:1c.4: MEM window: disabled
pci 0000:00:1c.4: PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:0a
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: 0xe0000000-0xe00fffff
pci 0000:00:1e.0: PREFETCH window: disabled
xen: registering gsi 16 triggering 0 polarity 1
alloc irq_desc for 16 on node 0
alloc kstat_irqs on node 0
xen: --> irq=16
xen_set_ioapic_routing: irq 16 gsi 16 vector 184 ioapic 0 pin 16 triggering 1 polarity 1
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:01:00.0: setting latency timer to 64
xen: registering gsi 17 triggering 0 polarity 1
alloc irq_desc for 17 on node 0
alloc kstat_irqs on node 0
xen: --> irq=17
xen_set_ioapic_routing: irq 17 gsi 17 vector 192 ioapic 0 pin 17 triggering 1 polarity 1
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:03:00.0: setting latency timer to 64
xen: registering gsi 20 triggering 0 polarity 1
alloc irq_desc for 20 on node 0
alloc kstat_irqs on node 0
xen: --> irq=20
xen_set_ioapic_routing: irq 20 gsi 20 vector 200 ioapic 0 pin 20 triggering 1 polarity 1
pci 0000:00:1c.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:05:00.0: setting latency timer to 64
xen: registering gsi 18 triggering 0 polarity 1
alloc irq_desc for 18 on node 0
alloc kstat_irqs on node 0
xen: --> irq=18
xen_set_ioapic_routing: irq 18 gsi 18 vector 208 ioapic 0 pin 18 triggering 1 polarity 1
pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64
xen: registering gsi 19 triggering 0 polarity 1
alloc irq_desc for 19 on node 0
alloc kstat_irqs on node 0
xen: --> irq=19
xen_set_ioapic_routing: irq 19 gsi 19 vector 216 ioapic 0 pin 19 triggering 1 polarity 1
pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
xen: registering gsi 17 triggering 0 polarity 1
xen_allocate_pirq: returning irq 17 for gsi 17
xen: --> irq=17
xen_set_ioapic_routing: irq 17 gsi 17 vector 192 ioapic 0 pin 17 triggering 1 polarity 1
pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 1 mem: [0xe0500000-0xe05fffff]
pci_bus 0000:02: resource 1 mem: [0xe0500000-0xe05fffff]
pci_bus 0000:03: resource 1 mem: [0xe0300000-0xe03fffff]
pci_bus 0000:04: resource 1 mem: [0xe0300000-0xe03fffff]
pci_bus 0000:05: resource 1 mem: [0xe0200000-0xe02fffff]
pci_bus 0000:06: resource 1 mem: [0xe0200000-0xe02fffff]
pci_bus 0000:07: resource 0 io: [0x1000-0x1fff]
pci_bus 0000:07: resource 1 mem: [0xe0100000-0xe01fffff]
pci_bus 0000:0a: resource 1 mem: [0xe0000000-0xe00fffff]
pci_bus 0000:0a: resource 3 io: [0x00-0xffff]
pci_bus 0000:0a: resource 4 mem: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 10, 4718592 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 211314k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1273579720.766:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 1312
SELinux: Registering netfilter hooks
cryptomgr_test used greatest stack depth: 5480 bytes left
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
alloc irq_desc for 249 on node 0
alloc kstat_irqs on node 0
pcieport-driver 0000:00:01.0: setting latency timer to 64
alloc irq_desc for 248 on node 0
alloc kstat_irqs on node 0
pcieport-driver 0000:00:1c.0: setting latency timer to 64
alloc irq_desc for 247 on node 0
alloc kstat_irqs on node 0
pcieport-driver 0000:00:1c.1: setting latency timer to 64
alloc irq_desc for 246 on node 0
alloc kstat_irqs on node 0
pcieport-driver 0000:00:1c.2: setting latency timer to 64
alloc irq_desc for 245 on node 0
alloc kstat_irqs on node 0
pcieport-driver 0000:00:1c.3: setting latency timer to 64
alloc irq_desc for 244 on node 0
alloc kstat_irqs on node 0
pcieport-driver 0000:00:1c.4: setting latency timer to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
acpiphp_glue: can't get bus number, assuming 0
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button [PWRF]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
ACPI: Sleep Button [SLPB]
ACPI: Invalid PBLK length [0]
ACPI: Invalid PBLK length [0]
ACPI: Invalid PBLK length [0]
ACPI: Invalid PBLK length [0]
Event-channel device installed.
registering netback
xen: registering gsi 19 triggering 0 polarity 1
xen_allocate_pirq: returning irq 19 for gsi 19
xen: --> irq=19
xen_set_ioapic_routing: irq 19 gsi 19 vector 216 ioapic 0 pin 19 triggering 1 polarity 1
pciback 0000:0a:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
pciback 0000:0a:03.0: PCI INT A disabled
xen: registering gsi 23 triggering 0 polarity 1
alloc irq_desc for 23 on node 0
alloc kstat_irqs on node 0
xen: --> irq=23
xen_set_ioapic_routing: irq 23 gsi 23 vector 81 ioapic 0 pin 23 triggering 1 polarity 1
pciback 0000:0a:00.2: PCI INT C -> GSI 23 (level, low) -> IRQ 23
pciback 0000:0a:00.2: PCI INT C disabled
xen: registering gsi 22 triggering 0 polarity 1
alloc irq_desc for 22 on node 0
alloc kstat_irqs on node 0
xen: --> irq=22
xen_set_ioapic_routing: irq 22 gsi 22 vector 89 ioapic 0 pin 22 triggering 1 polarity 1
pciback 0000:0a:00.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22
pciback 0000:0a:00.1: PCI INT B disabled
xen: registering gsi 21 triggering 0 polarity 1
alloc irq_desc for 21 on node 0
alloc kstat_irqs on node 0
xen: --> irq=21
xen_set_ioapic_routing: irq 21 gsi 21 vector 97 ioapic 0 pin 21 triggering 1 polarity 1
pciback 0000:0a:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
pciback 0000:0a:00.0: PCI INT A disabled
xen: registering gsi 19 triggering 0 polarity 1
xen_allocate_pirq: returning irq 19 for gsi 19
xen: --> irq=19
xen_set_ioapic_routing: irq 19 gsi 19 vector 216 ioapic 0 pin 19 triggering 1 polarity 1
pciback 0000:06:00.2: PCI INT C -> GSI 19 (level, low) -> IRQ 19
pciback 0000:06:00.2: PCI INT C disabled
xen: registering gsi 18 triggering 0 polarity 1
xen_allocate_pirq: returning irq 18 for gsi 18
xen: --> irq=18
xen_set_ioapic_routing: irq 18 gsi 18 vector 208 ioapic 0 pin 18 triggering 1 polarity 1
pciback 0000:06:00.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
pciback 0000:06:00.1: PCI INT B disabled
xen: registering gsi 17 triggering 0 polarity 1
xen_allocate_pirq: returning irq 17 for gsi 17
xen: --> irq=17
xen_set_ioapic_routing: irq 17 gsi 17 vector 192 ioapic 0 pin 17 triggering 1 polarity 1
pciback 0000:06:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pciback 0000:06:00.0: PCI INT A disabled
xen: registering gsi 18 triggering 0 polarity 1
xen_allocate_pirq: returning irq 18 for gsi 18
xen: --> irq=18
xen_set_ioapic_routing: irq 18 gsi 18 vector 208 ioapic 0 pin 18 triggering 1 polarity 1
pciback 0000:04:00.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pciback 0000:04:00.2: PCI INT C disabled
xen: registering gsi 17 triggering 0 polarity 1
xen_allocate_pirq: returning irq 17 for gsi 17
xen: --> irq=17
xen_set_ioapic_routing: irq 17 gsi 17 vector 192 ioapic 0 pin 17 triggering 1 polarity 1
pciback 0000:04:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pciback 0000:04:00.1: PCI INT B disabled
xen: registering gsi 16 triggering 0 polarity 1
xen_allocate_pirq: returning irq 16 for gsi 16
xen: --> irq=16
xen_set_ioapic_routing: irq 16 gsi 16 vector 184 ioapic 0 pin 16 triggering 1 polarity 1
pciback 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pciback 0000:04:00.0: PCI INT A disabled
xen: registering gsi 18 triggering 0 polarity 1
xen_allocate_pirq: returning irq 18 for gsi 18
xen: --> irq=18
xen_set_ioapic_routing: irq 18 gsi 18 vector 208 ioapic 0 pin 18 triggering 1 polarity 1
pciback 0000:02:00.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pciback 0000:02:00.2: PCI INT C disabled
xen: registering gsi 17 triggering 0 polarity 1
xen_allocate_pirq: returning irq 17 for gsi 17
xen: --> irq=17
xen_set_ioapic_routing: irq 17 gsi 17 vector 192 ioapic 0 pin 17 triggering 1 polarity 1
pciback 0000:02:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pciback 0000:02:00.1: PCI INT B disabled
xen: registering gsi 16 triggering 0 polarity 1
xen_allocate_pirq: returning irq 16 for gsi 16
xen: --> irq=16
xen_set_ioapic_routing: irq 16 gsi 16 vector 184 ioapic 0 pin 16 triggering 1 polarity 1
pciback 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pciback 0000:02:00.0: PCI INT A disabled
alloc irq_desc for 243 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 242 on node 0
alloc kstat_irqs on node 0
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel Q35 Chipset
agpgart-intel 0000:00:00.0: detected 6140K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
tpm_tis 00:07: 1.2 TPM (device-id 0xFE, rev-id 70)
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input2
ahci 0000:00:1f.2: version 3.0
xen: registering gsi 21 triggering 0 polarity 1
xen_allocate_pirq: returning irq 21 for gsi 21
xen: --> irq=21
xen_set_ioapic_routing: irq 21 gsi 21 vector 97 ioapic 0 pin 21 triggering 1 polarity 1
ahci 0000:00:1f.2: PCI INT A -> GSI 21 (level, low) -> IRQ 21
alloc irq_desc for 241 on node 0
alloc kstat_irqs on node 0
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pmp pio slum part ems
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 241
ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 241
ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 241
ata4: SATA max UDMA/133 abar m2048@0xe0725000 port 0xe0725280 irq 241
ata5: SATA max UDMA/133 abar m2048@0xe0725000 port 0xe0725300 irq 241
ata6: SATA max UDMA/133 abar m2048@0xe0725000 port 0xe0725380 irq 241
work_for_cpu used greatest stack depth: 4992 bytes left
Fixed MDIO Bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
xen: registering gsi 17 triggering 0 polarity 1
xen_allocate_pirq: returning irq 17 for gsi 17
xen: --> irq=17
xen_set_ioapic_routing: irq 17 gsi 17 vector 192 ioapic 0 pin 17 triggering 1 polarity 1
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 17, io mem 0xe0725c00
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.31.6 ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
work_for_cpu used greatest stack depth: 3936 bytes left
xen: registering gsi 23 triggering 0 polarity 1
xen_allocate_pirq: returning irq 23 for gsi 23
xen: --> irq=23
xen_set_ioapic_routing: irq 23 gsi 23 vector 81 ioapic 0 pin 23 triggering 1 polarity 1
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0725800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.31.6 ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
xen: registering gsi 18 triggering 0 polarity 1
xen_allocate_pirq: returning irq 18 for gsi 18
xen: --> irq=18
xen_set_ioapic_routing: irq 18 gsi 18 vector 208 ioapic 0 pin 18 triggering 1 polarity 1
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 18, io base 0x000020e0
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.31.6 uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
xen: registering gsi 21 triggering 0 polarity 1
xen_allocate_pirq: returning irq 21 for gsi 21
xen: --> irq=21
xen_set_ioapic_routing: irq 21 gsi 21 vector 97 ioapic 0 pin 21 triggering 1 polarity 1
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.31.6 uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
xen: registering gsi 17 triggering 0 polarity 1
xen_allocate_pirq: returning irq 17 for gsi 17
xen: --> irq=17
xen_set_ioapic_routing: irq 17 gsi 17 vector 192 ioapic 0 pin 17 triggering 1 polarity 1
uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1a.2: setting latency timer to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: irq 17, io base 0x000020a0
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.31.6 uhci_hcd
usb usb5: SerialNumber: 0000:00:1a.2
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
xen: registering gsi 23 triggering 0 polarity 1
xen_allocate_pirq: returning irq 23 for gsi 23
xen: --> irq=23
xen_set_ioapic_routing: irq 23 gsi 23 vector 81 ioapic 0 pin 23 triggering 1 polarity 1
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.31.6 uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.0
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
xen: registering gsi 19 triggering 0 polarity 1
xen_allocate_pirq: returning irq 19 for gsi 19
xen: --> irq=19
xen_set_ioapic_routing: irq 19 gsi 19 vector 216 ioapic 0 pin 19 triggering 1 polarity 1
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.31.6 uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.1
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
xen: registering gsi 18 triggering 0 polarity 1
xen_allocate_pirq: returning irq 18 for gsi 18
xen: --> irq=18
xen_set_ioapic_routing: irq 18 gsi 18 vector 208 ioapic 0 pin 18 triggering 1 polarity 1
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040
usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb8: Product: UHCI Host Controller
usb usb8: Manufacturer: Linux 2.6.31.6 uhci_hcd
usb usb8: SerialNumber: 0000:00:1d.2
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 2 ports detected
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 114 bytes nvram
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (6144 buckets, 24576 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
PM: Resume from disk failed.
registered taskstats version 1
No TPM chip found, activating TPM-bypass!
Magic number: 10:156:127
acpi device:02: hash matches
rtc_cmos 00:03: setting system clock to 2010-05-11 12:08:40 UTC (1273579720)
Initalizing network drop monitor service
ata6: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: TSSTcorp CDDVDW SH-S223C, SB00, max UDMA/100
ata3.00: configured for UDMA/100
ata1.00: ATA-8: WDC WD2500AAJS-52B4A0, 01.03A01, max UDMA/133
ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2.00: HPA detected: current 488395055, native 488397168
ata2.00: ATA-8: WDC WD2500AAJS-52B4A0, 01.03A01, max UDMA/133
ata2.00: 488395055 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD2500AAJS-5 01.0 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Direct-Access ATA WDC WD2500AAJS-5 01.0 PQ: 0 ANSI: 5
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: [sdb] 488395055 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb:
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sdb1 sdb2 sdb3
sd 1:0:0:0: [sdb] Attached SCSI disk
scsi 2:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S223C SB00 PQ: 0 ANSI: 5
sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 52x/52x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sr 2:0:0:0: Attached scsi generic sg2 type 5
Freeing unused kernel memory: 3208k freed
Write protecting the kernel read-only data: 7480k
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
xen: registering gsi 20 triggering 0 polarity 1
xen_allocate_pirq: returning irq 20 for gsi 20
xen: --> irq=20
xen_set_ioapic_routing: irq 20 gsi 20 vector 200 ioapic 0 pin 20 triggering 1 polarity 1
e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
e1000e 0000:00:19.0: pci_enable_pcie_error_reporting failed 0xfffffffb
e1000e 0000:00:19.0: setting latency timer to 64
alloc irq_desc for 240 on node 0
alloc kstat_irqs on node 0
xen: registering gsi 18 triggering 0 polarity 1
xen_allocate_pirq: returning irq 18 for gsi 18
xen: --> irq=18
xen_set_ioapic_routing: irq 18 gsi 18 vector 208 ioapic 0 pin 18 triggering 1 polarity 1
pata_acpi 0000:07:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pata_acpi 0000:07:00.0: setting latency timer to 64
pata_acpi 0000:07:00.0: PCI INT A disabled
xen: registering gsi 18 triggering 0 polarity 1
xen_allocate_pirq: returning irq 18 for gsi 18
xen: --> irq=18
xen_set_ioapic_routing: irq 18 gsi 18 vector 208 ioapic 0 pin 18 triggering 1 polarity 1
pata_marvell 0000:07:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pata_marvell 0000:07:00.0: setting latency timer to 64
scsi6 : pata_marvell
scsi7 : pata_marvell
ata7: PATA max UDMA/100 cmd 0x1018 ctl 0x1024 bmdma 0x1000 irq 18
ata8: DUMMY
0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1c:c0:cb:ba:89
0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
0000:00:19.0: eth0: MAC: 7, PHY: 6, PBA No: ffffff-0ff
cdrom_id used greatest stack depth: 3896 bytes left
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: md0 stopped.
md: bind<sdb1>
md: bind<sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md0: detected capacity change from 0 to 15998058496
md: md1 stopped.
md0: unknown partition table
md: bind<sdb2>
md: bind<sda2>
raid0: looking at sda2
raid0: comparing sda2(3903616)
with sda2(3903616)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at sdb2
raid0: comparing sdb2(3903616)
with sda2(3903616)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 7807232 sectors.
******* md1 configuration *********
zone0=[sda2/sdb2/]
zone offset=0kb device offset=0kb size=3903616kb
**********************************
md1: detected capacity change from 0 to 3997302784
md: md2 stopped.
md1: unknown partition table
md: bind<sdb3>
md: bind<sda3>
raid1: raid set md2 active with 2 out of 2 mirrors
md2: detected capacity change from 0 to 232059699200
md2: unknown partition table
PM: Starting manual resume from disk
PM: Resume from partition 9:1
PM: Checking hibernation image.
PM: Resume from disk failed.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
exe used greatest stack depth: 3760 bytes left
stty used greatest stack depth: 3184 bytes left
udevd version 125 started
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
xen: registering gsi 22 triggering 0 polarity 1
xen_allocate_pirq: returning irq 22 for gsi 22
xen: --> irq=22
xen_set_ioapic_routing: irq 22 gsi 22 vector 89 ioapic 0 pin 22 triggering 1 polarity 1
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
ALSA sound/pci/hda/hda_codec.c:3857: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3861: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3865: hp_outs=1 (0x15/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3866: mono: mono_out=0x0
ALSA sound/pci/hda/hda_codec.c:3877: inputs: mic=0x18, fmic=0x1a, line=0x19, fline=0x0, cd=0x0, aux=0x0
ALSA sound/pci/hda/patch_realtek.c:1181: realtek: No valid SSID, checking pincfg 0x411111f0 for NID 0x1d
ALSA sound/pci/hda/patch_realtek.c:1255: realtek: Enable default setup for auto mode as fallback
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input3
input: PC Speaker as /devices/platform/pcspkr/input/input4
xen: registering gsi 18 triggering 0 polarity 1
xen_allocate_pirq: returning irq 18 for gsi 18
xen: --> irq=18
xen_set_ioapic_routing: irq 18 gsi 18 vector 208 ioapic 0 pin 18 triggering 1 polarity 1
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18
Error: Driver 'pcspkr' is already registered, aborting...
Adding 3903608k swap on /dev/md1. Priority:-1 extents:1 across:3903608k
EXT3 FS on md0, internal journal
rc used greatest stack depth: 2896 bytes left
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Bridge firewalling registered
ADDRCONF(NETDEV_UP): peth0: link is not ready
e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready
device peth0 entered promiscuous mode
eth0: port 1(peth0) entering forwarding state
alloc irq_desc for 239 on node 0
alloc kstat_irqs on node 0
xenbus_probe wake_waiting
xenbus_probe wake_waiting
alloc irq_desc for 238 on node 0
alloc kstat_irqs on node 0
XENBUS: Unable to read cpu state
xenbus_probe_devices backend
xenbus_probe_devices failed xenbus_directory
backend_probe_and_watch devices probed ok
backend_probe_and_watch watch add ok ok
backend_probe_and_watch all done
alloc irq_desc for 237 on node 0
alloc kstat_irqs on node 0
02:00.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e0501000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pciback
02:00.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at e0500000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pciback
02:00.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (4000ns min, 8500ns max), Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at e0502000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pciback
[-- Attachment #3: NOTWORKING.txt --]
[-- Type: text/plain, Size: 90941 bytes --]
scanmaster2:~# uname -a
Linux scanmaster2 2.6.32.12 #1 SMP Fri May 14 13:40:05 EDT 2010 x86_64 GNU/Linux
scanmaster2:~# xm info
host : scanmaster2
release : 2.6.32.12
version : #1 SMP Fri May 14 13:40:05 EDT 2010
machine : x86_64
nr_cpus : 8
nr_nodes : 1
cores_per_socket : 4
threads_per_core : 2
cpu_mhz : 2800
hw_caps : bfebfbff:28100800:00000000:00001b40:0098e3bd:00000000:00000001:00000000
virt_caps : hvm hvm_directio
total_memory : 7932
free_memory : 6023
node_to_cpu : node0:0-7
node_to_memory : node0:6023
node_to_dma32_mem : node0:3249
max_node_id : 0
xen_major : 4
xen_minor : 0
xen_extra : .0
xen_caps : xen-3.0-x86_64 xen-3.0-x86_32p hvm-3.0-x86_32 hvm-3.0-x86_32p hvm-3.0-x86_64
xen_scheduler : credit
xen_pagesize : 4096
platform_params : virt_start=0xffff800000000000
xen_changeset : unavailable
xen_commandline : iommu=verbose dom0_mem=2048M
cc_compiler : gcc version 4.3.2 (Debian 4.3.2-1.1)
cc_compile_by : root
cc_compile_domain :
cc_compile_date : Thu May 6 13:41:25 EDT 2010
xend_config_format : 4
__ __ _ _ ___ ___
\ \/ /___ _ __ | || | / _ \ / _ \
\ // _ \ \047_ \ | || |_| | | | | | |
/ \ __/ | | | |__ _| |_| | |_| |
/_/\_\___|_| |_| |_|(_)___(_)___/
(XEN) Xen version 4.0.0 (root@) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) Thu May 6 13:41:25 EDT 2010
(XEN) Latest ChangeSet: unavailable
(XEN) Command line: iommu=verbose dom0_mem=2048M
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: V2; EDID transfer time: 1 seconds
(XEN) Disc information:
(XEN) Found 2 MBR signatures
(XEN) Found 2 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000008f000 (usable)
(XEN) 000000000008f000 - 0000000000090000 (reserved)
(XEN) 0000000000090000 - 000000000009ec00 (usable)
(XEN) 000000000009ec00 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000cf4bd000 (usable)
(XEN) 00000000cf4bd000 - 00000000cf4bf000 (reserved)
(XEN) 00000000cf4bf000 - 00000000cf4c2000 (usable)
(XEN) 00000000cf4c2000 - 00000000cf7bf000 (ACPI NVS)
(XEN) 00000000cf7bf000 - 00000000cf7df000 (usable)
(XEN) 00000000cf7df000 - 00000000cf7ff000 (ACPI data)
(XEN) 00000000cf7ff000 - 00000000cf800000 (usable)
(XEN) 00000000cf800000 - 00000000d0000000 (reserved)
(XEN) 00000000f8000000 - 00000000fd000000 (reserved)
(XEN) 00000000ffe00000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 0000000230000000 (usable)
(XEN) ACPI: RSDP 000FE020, 0024 (r2 INTEL )
(XEN) ACPI: XSDT CF7FE120, 0074 (r1 INTEL DX58SO 11F6 1000013)
(XEN) ACPI: FACP CF7FD000, 00F4 (r3 INTEL DX58SO 11F6 MSFT 100000D)
(XEN) ACPI Warning (tbfadt-0444): Optional field "Pm2ControlBlock" has zero address or length: 0000000000000450/0 [20070126]
(XEN) ACPI: DSDT CF7F8000, 4641 (r2 INTEL DX58SO 11F6 MSFT 100000D)
(XEN) ACPI: FACS CF728000, 0040
(XEN) ACPI: APIC CF7F7000, 0138 (r2 INTEL DX58SO 11F6 MSFT 100000D)
(XEN) ACPI: WDDT CF7F6000, 0040 (r1 INTEL DX58SO 11F6 MSFT 100000D)
(XEN) ACPI: MCFG CF7F5000, 003C (r1 INTEL DX58SO 11F6 MSFT 100000D)
(XEN) ACPI: ASF! CF7F4000, 00AC (r32 INTEL DX58SO 11F6 MSFT 100000D)
(XEN) ACPI: HPET CF7F3000, 0038 (r1 INTEL DX58SO 11F6 MSFT 100000D)
(XEN) ACPI: SSDT CF7E2000, E134 (r1 INTEL SSDT PM 11F6 MSFT 100000D)
(XEN) ACPI: DMAR CF7DF000, 0140 (r1 INTEL DX58SO 11F6 MSFT 100000D)
(XEN) ACPI: WDTT CF7F1000, 020C (r2 INTEL DX58SO 11F6 MSFT 100000D)
(XEN) ACPI: ASPT CF7F2000, 0034 (r4 INTEL PerfTune 11F6 MSFT 100000D)
(XEN) System RAM: 7932MB (8123268kB)
(XEN) Domain heap initialised
(XEN) Processor #0 7:10 APIC version 21
(XEN) Processor #2 7:10 APIC version 21
(XEN) Processor #4 7:10 APIC version 21
(XEN) Processor #6 7:10 APIC version 21
(XEN) Processor #1 7:10 APIC version 21
(XEN) Processor #3 7:10 APIC version 21
(XEN) Processor #5 7:10 APIC version 21
(XEN) Processor #7 7:10 APIC version 21
(XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) [VT-D]dmar.c:679: Host address width 39
(XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD:
(XEN) [VT-D]dmar.c:398: dmaru->address = fe711000
(XEN) [VT-D]dmar.c:334: endpoint: 0:1b.0
(XEN) [VT-D]dmar.c:694: found ACPI_DMAR_DRHD:
(XEN) [VT-D]dmar.c:398: dmaru->address = fe710000
(XEN) [VT-D]dmar.c:340: IOAPIC: f0:1f.7
(XEN) [VT-D]dmar.c:411: flags: INCLUDE_ALL
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr e9000 end_address e9fff
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.1
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr ea000 end_address eafff
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.2
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr eb000 end_address ebfff
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.0
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr e6000 end_address e6fff
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.1
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr e7000 end_address e7fff
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1a.2
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr e8000 end_address e8fff
(XEN) [VT-D]dmar.c:699: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:334: endpoint: 0:1d.0
(XEN) [VT-D]dmar.c:571: RMRR region: base_addr ec000 end_address eefff
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 2800.177 MHz processor.
(XEN) Initing memory sharing.
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Extended Page Tables (EPT)
(XEN) - Virtual-Processor Identifiers (VPID)
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: ASIDs enabled.
(XEN) HVM: VMX enabled
(XEN) HVM: Hardware Assisted Paging detected.
(XEN) [VT-D]iommu.c:1078: drhd->address = fe711000 iommu->reg = ffff82c3fff57000
(XEN) [VT-D]iommu.c:1080: cap = c9008010e60262 ecap = f0207a
(XEN) [VT-D]iommu.c:1078: drhd->address = fe710000 iommu->reg = ffff82c3fff56000
(XEN) [VT-D]iommu.c:1080: cap = c90780106f0462 ecap = f020fa
(XEN) Intel VT-d Snoop Control not supported.
(XEN) Intel VT-d DMA Passthrough not supported.
(XEN) Intel VT-d Queued Invalidation supported.
(XEN) Intel VT-d Interrupt Remapping supported.
(XEN) I/O virtualisation enabled
(XEN) I/O virtualisation for PV guests disabled
(XEN) Total of 8 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) TSC is reliable, synchronization unnecessary
(XEN) Platform timer is 14.318MHz HPET
(XEN) Allocated console ring of 16 KiB.
(XEN) Brought up 8 CPUs
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:10.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:10.1
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.0
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.1
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:14.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:14.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:19.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1a.7
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 0:1b.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1d.7
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 0:1f.5
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 2:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 2:0.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 2:0.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 4:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 4:0.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 4:0.2
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = 5:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 7:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 7:0.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 7:0.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 9:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 9:0.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 9:0.2
(XEN) [VT-D]iommu.c:1325: d0:PCIe: map bdf = a:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.4
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.5
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.6
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = b:3.7
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:0.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:0.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:2.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:2.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:3.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:3.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:3.4
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:4.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:4.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:4.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:4.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:5.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:5.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:5.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:5.3
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:6.0
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:6.1
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:6.2
(XEN) [VT-D]iommu.c:1332: d0:PCI: map bdf = 3f:6.3
(XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg = ffff82c3fff57000
(XEN) [VT-D]iommu.c:695: iommu_enable_translation: iommu->reg = ffff82c3fff56000
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x1a92000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000200000000->0000000220000000 (393216 pages to be allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff81000000->ffffffff81a92000
(XEN) Init. ramdisk: ffffffff81a92000->ffffffff8fb9d200
(XEN) Phys-Mach map: ffffffff8fb9e000->ffffffff8ff9e000
(XEN) Start info: ffffffff8ff9e000->ffffffff8ff9e4b4
(XEN) Page tables: ffffffff8ff9f000->ffffffff90024000
(XEN) Boot stack: ffffffff90024000->ffffffff90025000
(XEN) TOTAL: ffffffff80000000->ffffffff90400000
(XEN) ENTRY ADDRESS: ffffffff81895200
(XEN) Dom0 has maximum 8 VCPUs
(XEN) Scrubbing Free RAM: ............................................................done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: Errors and warnings
(XEN) Guest Loglevel: Nothing (Rate-limited: Errors and warnings)
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type \047CTRL-a\047 three times to switch input to Xen)
(XEN) Freed 164kB init memory.
(XEN) [VT-D]iommu.c:1461: d0:PCI: unmap bdf = 2:0.0
(XEN) [VT-D]iommu.c:1332: d1:PCI: map bdf = 2:0.0
(XEN) domctl.c:853:d0 XEN_DOMCTL_assign_device: assign device (2:0.0) failed
(XEN) [VT-D]iommu.c:1461: d0:PCI: unmap bdf = 2:0.0
(XEN) [VT-D]iommu.c:1332: d2:PCI: map bdf = 2:0.0
(XEN) domctl.c:853:d0 XEN_DOMCTL_assign_device: assign device (2:0.0) failed
(XEN) event_channel.c:192:d0 EVTCHNOP failure: domain 2, error -22
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32.12 (root@scanmaster2) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 SMP Fri May 14 13:40:05 EDT 2010
[ 0.000000] Command line: root=/dev/md0 ro console=tty0 xen-pciback.permissive pci=resource_alignment=02:00.0;02:00.1;02:00.2 xen-pciback.hide=(02:00.0)(02:00.1)(02:00.2)(0b:
02.0)(0b:02.1)(0b:03.0)(03:00.0)
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] released 0 pages of unused memory
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] Xen: 0000000000000000 - 000000000008f000 (usable)
[ 0.000000] Xen: 000000000008f000 - 0000000000090000 (reserved)
[ 0.000000] Xen: 0000000000090000 - 000000000009ec00 (usable)
[ 0.000000] Xen: 000000000009ec00 - 0000000000100000 (reserved)
[ 0.000000] Xen: 0000000000100000 - 0000000080000000 (usable)
[ 0.000000] Xen: 00000000cf4bd000 - 00000000cf4bf000 (reserved)
[ 0.000000] Xen: 00000000cf4c2000 - 00000000cf7bf000 (ACPI NVS)
[ 0.000000] Xen: 00000000cf7df000 - 00000000cf7ff000 (ACPI data)
[ 0.000000] Xen: 00000000cf800000 - 00000000d0000000 (reserved)
[ 0.000000] Xen: 00000000f8000000 - 00000000fd000000 (reserved)
[ 0.000000] Xen: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] Xen: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] Xen: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.5 present.
[ 0.000000] last_pfn = 0x80000 max_arch_pfn = 0x400000000
[ 0.000000] x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
[ 0.000000] e820 update range: 0000000000001000 - 0000000000006000 (usable) ==> (reserved)
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000001000 (usable)
[ 0.000000] modified: 0000000000001000 - 0000000000006000 (reserved)
[ 0.000000] modified: 0000000000006000 - 000000000008f000 (usable)
[ 0.000000] modified: 000000000008f000 - 0000000000090000 (reserved)
[ 0.000000] modified: 0000000000090000 - 000000000009ec00 (usable)
[ 0.000000] modified: 000000000009ec00 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 0000000080000000 (usable)
[ 0.000000] modified: 00000000cf4bd000 - 00000000cf4bf000 (reserved)
[ 0.000000] modified: 00000000cf4c2000 - 00000000cf7bf000 (ACPI NVS)
[ 0.000000] modified: 00000000cf7df000 - 00000000cf7ff000 (ACPI data)
[ 0.000000] modified: 00000000cf800000 - 00000000d0000000 (reserved)
[ 0.000000] modified: 00000000f8000000 - 00000000fd000000 (reserved)
[ 0.000000] modified: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] modified: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-0000000080000000
[ 0.000000] 0000000000 - 0080000000 page 4k
[ 0.000000] kernel direct mapping tables up to 80000000 @ 100000-503000
[ 0.000000] RAMDISK: 01a92000 - 0fb9d200
[ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL )
[ 0.000000] ACPI: XSDT 00000000cf7fe120 00074 (v01 INTEL DX58SO 000011F6 01000013)
[ 0.000000] ACPI: FACP 00000000cf7fd000 000F4 (v03 INTEL DX58SO 000011F6 MSFT 0100000D)
[ 0.000000] ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 0000000000000450/0 (20090903/tbfadt-557)
[ 0.000000] ACPI Warning: Invalid length for Pm2ControlBlock: 0, using default 8 (20090903/tbfadt-607)
[ 0.000000] ACPI: DSDT 00000000cf7f8000 04641 (v02 INTEL DX58SO 000011F6 MSFT 0100000D)
[ 0.000000] ACPI: FACS 00000000cf728000 00040
[ 0.000000] ACPI: APIC 00000000cf7f7000 00138 (v02 INTEL DX58SO 000011F6 MSFT 0100000D)
[ 0.000000] ACPI: WDDT 00000000cf7f6000 00040 (v01 INTEL DX58SO 000011F6 MSFT 0100000D)
[ 0.000000] ACPI: MCFG 00000000cf7f5000 0003C (v01 INTEL DX58SO 000011F6 MSFT 0100000D)
[ 0.000000] ACPI: ASF! 00000000cf7f4000 000AC (v32 INTEL DX58SO 000011F6 MSFT 0100000D)
[ 0.000000] ACPI: HPET 00000000cf7f3000 00038 (v01 INTEL DX58SO 000011F6 MSFT 0100000D)
[ 0.000000] ACPI: SSDT 00000000cf7e2000 0E134 (v01 INTEL SSDT PM 000011F6 MSFT 0100000D)
[ 0.000000] ACPI: 00000000cf7df000 00140 (v01 INTEL DX58SO 000011F6 MSFT 0100000D)
[ 0.000000] ACPI: WDTT 00000000cf7f1000 0020C (v02 INTEL DX58SO 000011F6 MSFT 0100000D)
[ 0.000000] ACPI: ASPT 00000000cf7f2000 00034 (v04 INTEL PerfTune 000011F6 MSFT 0100000D)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000080000000
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000080000000
[ 0.000000] NODE_DATA [0000000000008000 - 000000000000cfff]
[ 0.000000] bootmap [000000000000d000 - 000000000001cfff] pages 10
[ 0.000000] (8 early reservations) ==> bootmem [0000000000 - 0080000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [000ff9f000 - 0010024000] XEN PAGETABLES ==> [000ff9f000 - 0010024000]
[ 0.000000] #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #3 [0001000000 - 0001a718e4] TEXT DATA BSS ==> [0001000000 - 0001a718e4]
[ 0.000000] #4 [0001a92000 - 000fb9d200] RAMDISK ==> [0001a92000 - 000fb9d200]
[ 0.000000] #5 [000fb9e000 - 000ff9f000] XEN START INFO ==> [000fb9e000 - 000ff9f000]
[ 0.000000] #6 [0001a72000 - 0001a7215e] BRK ==> [0001a72000 - 0001a7215e]
[ 0.000000] #7 [0000100000 - 000047b000] PGTABLE ==> [0000100000 - 000047b000]
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[4] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00000001
[ 0.000000] 0: 0x00000006 -> 0x0000008f
[ 0.000000] 0: 0x00000090 -> 0x0000009e
[ 0.000000] 0: 0x00000100 -> 0x00080000
[ 0.000000] On node 0 totalpages: 524184
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 894 pages reserved
[ 0.000000] DMA zone: 3042 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7112 pages used for memmap
[ 0.000000] DMA32 zone: 513080 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-0
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ERROR: Unable to locate IOAPIC for GSI 2
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ERROR: Unable to locate IOAPIC for GSI 9
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[ 0.000000] SMP: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 256
[ 0.000000] PM: Registered nosave memory: 0000000000001000 - 0000000000006000
[ 0.000000] PM: Registered nosave memory: 000000000008f000 - 0000000000090000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:4f4bd000)
[ 0.000000] Booting paravirtualized kernel on Xen
[ 0.000000] Xen version: 4.0.0 (preserve-AD) (dom0)
[ 0.000000] NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff88001005a000 s91416 r8192 d23272 u122880
[ 0.000000] pcpu-alloc: s91416 r8192 d23272 u122880 alloc=30*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7
[ 0.101661] trying to map vcpu_info 0 at ffff880010065020, mfn 210065, offset 32
[ 0.101665] cpu 0 using vcpu_info at ffff880010065020
[ 0.101667] trying to map vcpu_info 1 at ffff880010083020, mfn 210083, offset 32
[ 0.101669] cpu 1 using vcpu_info at ffff880010083020
[ 0.101671] trying to map vcpu_info 2 at ffff8800100a1020, mfn 2100a1, offset 32
[ 0.101673] cpu 2 using vcpu_info at ffff8800100a1020
[ 0.101675] trying to map vcpu_info 3 at ffff8800100bf020, mfn 2100bf, offset 32
[ 0.101677] cpu 3 using vcpu_info at ffff8800100bf020
[ 0.101679] trying to map vcpu_info 4 at ffff8800100dd020, mfn 2100dd, offset 32
[ 0.101681] cpu 4 using vcpu_info at ffff8800100dd020
[ 0.101683] trying to map vcpu_info 5 at ffff8800100fb020, mfn 2100fb, offset 32
[ 0.101685] cpu 5 using vcpu_info at ffff8800100fb020
[ 0.101687] trying to map vcpu_info 6 at ffff880010119020, mfn 210119, offset 32
[ 0.101689] cpu 6 using vcpu_info at ffff880010119020
[ 0.101691] trying to map vcpu_info 7 at ffff880010137020, mfn 210137, offset 32
[ 0.101693] cpu 7 using vcpu_info at ffff880010137020
[ 0.101694] Xen: using vcpu_info placement
[ 0.101699] Built 1 zonelists in Node order, mobility grouping on. Total pages: 516122
[ 0.101701] Policy zone: DMA32
[ 0.101703] Kernel command line: root=/dev/md0 ro console=tty0 xen-pciback.permissive pci=resource_alignment=02:00.0;02:00.1;02:00.2 xen-pciback.hide=(02:00.0)(02:00.1)(02:00
.2)(0b:02.0)(0b:02.1)(0b:03.0)(03:00.0)
[ 0.101732] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.102061] Initializing CPU#0
[ 0.114275] DMA: Placing 64MB software IO TLB between ffff880012016000 - ffff880016016000
[ 0.114279] DMA: software IO TLB at phys 0x12016000 - 0x16016000
[ 0.114281] xen_swiotlb_fixup: buf=ffff880012016000 size=67108864
[ 0.136136] xen_swiotlb_fixup: buf=ffff880016076000 size=32768
[ 0.142429] Memory: 1751436k/2097152k available (5631k kernel code, 416k absent, 345300k reserved, 3058k data, 816k init)
[ 0.142454] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.142482] Hierarchical RCU implementation.
[ 0.142488] NR_IRQS:4352 nr_irqs:2304
[ 0.142572] xen: --> irq=0
[ 0.142579] xen: --> irq=1
[ 0.142584] xen: --> irq=2
[ 0.142589] xen: --> irq=3
[ 0.142594] xen: --> irq=4
[ 0.142598] xen: --> irq=5
[ 0.142603] xen: --> irq=6
[ 0.142607] xen: --> irq=7
[ 0.142612] xen: --> irq=8
[ 0.142617] xen: --> irq=9
[ 0.142621] xen: --> irq=10
[ 0.142626] xen: --> irq=11
[ 0.142631] xen: --> irq=12
[ 0.142635] xen: --> irq=13
[ 0.142640] xen: --> irq=14
[ 0.142645] xen: --> irq=15
[ 0.142657] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.142660] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.142662] xen: sci override: source_irq=9 global_irq=9 trigger=c polarity=1
[ 0.142664] xen: registering gsi 9 triggering 0 polarity 0
[ 0.142666] xen_allocate_pirq: returning irq 9 for gsi 9
[ 0.142668] xen: --> irq=9
[ 0.142700] xen: acpi sci 9
[ 0.144674] Console: colour VGA+ 80x25
[ 0.153136] console [tty0] enabled
[ 0.156719] allocated 20971520 bytes of page_cgroup
[ 0.156776] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.156878] Xen: using vcpuop timer interface
[ 0.156876] installing Xen timer for CPU 0
[ 0.156935] alloc irq_desc for 2303 on node 0
[ 0.156938] alloc kstat_irqs on node 0
[ 0.156953] Detected 2800.176 MHz processor.
[ 0.157009] Calibrating delay loop (skipped), value calculated using timer frequency.. 5600.35 BogoMIPS (lpj=28001760)
[ 0.157125] Security Framework initialized
[ 0.157178] SELinux: Disabled at boot.
[ 0.157538] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.158137] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.158379] Mount-cache hash table entries: 256
[ 0.159875] Initializing cgroup subsys ns
[ 0.159927] Initializing cgroup subsys cpuacct
[ 0.159979] Initializing cgroup subsys memory
[ 0.160034] Initializing cgroup subsys devices
[ 0.160086] Initializing cgroup subsys freezer
[ 0.160137] Initializing cgroup subsys net_cls
[ 0.160213] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.160291] CPU: L2 cache: 256K
[ 0.160339] CPU: L3 cache: 8192K
[ 0.160389] CPU 0/0x0 -> Node 0
[ 0.160437] CPU: Unsupported number of siblings 16
[ 0.160475] mce: CPU supports 9 MCE banks
[ 0.160583] Performance Events: unsupported p6 CPU model 26 no PMU driver, software events only.
[ 0.160719] SMP alternatives: switching to UP code
[ 0.192384] ACPI: Core revision 20090903
[ 0.207233] ftrace: converting mcount calls to 0f 1f 44 00 00
[ 0.207289] ftrace: allocating 21472 entries in 85 pages
[ 0.212402] alloc irq_desc for 2302 on node 0
[ 0.212405] alloc kstat_irqs on node 0
[ 0.212410] cpu 0 spinlock event irq 2302
[ 0.212463] alloc irq_desc for 2301 on node 0
[ 0.212465] alloc kstat_irqs on node 0
[ 0.212469] alloc irq_desc for 2300 on node 0
[ 0.212470] alloc kstat_irqs on node 0
[ 0.212474] alloc irq_desc for 2299 on node 0
[ 0.212476] alloc kstat_irqs on node 0
[ 0.212480] alloc irq_desc for 2298 on node 0
[ 0.212482] alloc kstat_irqs on node 0
[ 0.212634] installing Xen timer for CPU 1
[ 0.212686] alloc irq_desc for 2297 on node 0
[ 0.212688] alloc kstat_irqs on node 0
[ 0.212693] alloc irq_desc for 2296 on node 0
[ 0.212695] alloc kstat_irqs on node 0
[ 0.212698] cpu 1 spinlock event irq 2296
[ 0.212766] SMP alternatives: switching to SMP code
[ 0.242090] alloc irq_desc for 2295 on node 0
[ 0.242092] alloc kstat_irqs on node 0
[ 0.242102] alloc irq_desc for 2294 on node 0
[ 0.242104] alloc kstat_irqs on node 0
[ 0.242108] alloc irq_desc for 2293 on node 0
[ 0.242109] alloc kstat_irqs on node 0
[ 0.242115] alloc irq_desc for 2292 on node 0
[ 0.242116] alloc kstat_irqs on node 0
[ 0.000006] Initializing CPU#1
[ 0.000037] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.000039] CPU: L2 cache: 256K
[ 0.000040] CPU: L3 cache: 8192K
[ 0.000043] CPU 1/0x0 -> Node 0
[ 0.000045] CPU: Unsupported number of siblings 16
[ 0.242250] installing Xen timer for CPU 2
[ 0.242586] alloc irq_desc for 2291 on node 0
[ 0.242588] alloc kstat_irqs on node 0
[ 0.242592] alloc irq_desc for 2290 on node 0
[ 0.242594] alloc kstat_irqs on node 0
[ 0.242597] cpu 2 spinlock event irq 2290
[ 0.242661] alloc irq_desc for 2289 on node 0
[ 0.242663] alloc kstat_irqs on node 0
[ 0.242667] alloc irq_desc for 2288 on node 0
[ 0.242669] alloc kstat_irqs on node 0
[ 0.242672] alloc irq_desc for 2287 on node 0
[ 0.242674] alloc kstat_irqs on node 0
[ 0.242678] alloc irq_desc for 2286 on node 0
[ 0.242679] alloc kstat_irqs on node 0
[ 0.000005] Initializing CPU#2
[ 0.000034] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.000036] CPU: L2 cache: 256K
[ 0.000037] CPU: L3 cache: 8192K
[ 0.000040] CPU 2/0x0 -> Node 0
[ 0.000042] CPU: Unsupported number of siblings 16
[ 0.242803] installing Xen timer for CPU 3
[ 0.243138] alloc irq_desc for 2285 on node 0
[ 0.243140] alloc kstat_irqs on node 0
[ 0.243144] alloc irq_desc for 2284 on node 0
[ 0.243146] alloc kstat_irqs on node 0
[ 0.243149] cpu 3 spinlock event irq 2284
[ 0.243212] alloc irq_desc for 2283 on node 0
[ 0.243214] alloc kstat_irqs on node 0
[ 0.243218] alloc irq_desc for 2282 on node 0
[ 0.243220] alloc kstat_irqs on node 0
[ 0.243223] alloc irq_desc for 2281 on node 0
[ 0.243225] alloc kstat_irqs on node 0
[ 0.243229] alloc irq_desc for 2280 on node 0
[ 0.243230] alloc kstat_irqs on node 0
[ 0.000005] Initializing CPU#3
[ 0.000034] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.000036] CPU: L2 cache: 256K
[ 0.000037] CPU: L3 cache: 8192K
[ 0.000040] CPU 3/0x0 -> Node 0
[ 0.000041] CPU: Unsupported number of siblings 16
[ 0.243354] installing Xen timer for CPU 4
[ 0.243690] alloc irq_desc for 2279 on node 0
[ 0.243692] alloc kstat_irqs on node 0
[ 0.243696] alloc irq_desc for 2278 on node 0
[ 0.243698] alloc kstat_irqs on node 0
[ 0.243701] cpu 4 spinlock event irq 2278
[ 0.243764] alloc irq_desc for 2277 on node 0
[ 0.243766] alloc kstat_irqs on node 0
[ 0.243770] alloc irq_desc for 2276 on node 0
[ 0.243772] alloc kstat_irqs on node 0
[ 0.243776] alloc irq_desc for 2275 on node 0
[ 0.243777] alloc kstat_irqs on node 0
[ 0.243781] alloc irq_desc for 2274 on node 0
[ 0.243782] alloc kstat_irqs on node 0
[ 0.000004] Initializing CPU#4
[ 0.000041] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.000044] CPU: L2 cache: 256K
[ 0.000046] CPU: L3 cache: 8192K
[ 0.000050] CPU 4/0x0 -> Node 0
[ 0.000053] CPU: Unsupported number of siblings 16
[ 0.243929] installing Xen timer for CPU 5
[ 0.244265] alloc irq_desc for 2273 on node 0
[ 0.244267] alloc kstat_irqs on node 0
[ 0.244272] alloc irq_desc for 2272 on node 0
[ 0.244273] alloc kstat_irqs on node 0
[ 0.244277] cpu 5 spinlock event irq 2272
[ 0.244340] alloc irq_desc for 2271 on node 0
[ 0.244341] alloc kstat_irqs on node 0
[ 0.244346] alloc irq_desc for 2270 on node 0
[ 0.244347] alloc kstat_irqs on node 0
[ 0.244351] alloc irq_desc for 2269 on node 0
[ 0.244353] alloc kstat_irqs on node 0
[ 0.244357] alloc irq_desc for 2268 on node 0
[ 0.244358] alloc kstat_irqs on node 0
[ 0.000003] Initializing CPU#5
[ 0.000030] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.000032] CPU: L2 cache: 256K
[ 0.000033] CPU: L3 cache: 8192K
[ 0.000036] CPU 5/0x0 -> Node 0
[ 0.000037] CPU: Unsupported number of siblings 16
[ 0.244475] installing Xen timer for CPU 6
[ 0.244810] alloc irq_desc for 2267 on node 0
[ 0.244812] alloc kstat_irqs on node 0
[ 0.244816] alloc irq_desc for 2266 on node 0
[ 0.244818] alloc kstat_irqs on node 0
[ 0.244822] cpu 6 spinlock event irq 2266
[ 0.244884] alloc irq_desc for 2265 on node 0
[ 0.244886] alloc kstat_irqs on node 0
[ 0.244890] alloc irq_desc for 2264 on node 0
[ 0.244892] alloc kstat_irqs on node 0
[ 0.244896] alloc irq_desc for 2263 on node 0
[ 0.244898] alloc kstat_irqs on node 0
[ 0.244901] alloc irq_desc for 2262 on node 0
[ 0.244903] alloc kstat_irqs on node 0
[ 0.000004] Initializing CPU#6
[ 0.000030] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.000032] CPU: L2 cache: 256K
[ 0.000033] CPU: L3 cache: 8192K
[ 0.000036] CPU 6/0x0 -> Node 0
[ 0.000037] CPU: Unsupported number of siblings 16
[ 0.245021] installing Xen timer for CPU 7
[ 0.245357] alloc irq_desc for 2261 on node 0
[ 0.245359] alloc kstat_irqs on node 0
[ 0.245365] alloc irq_desc for 2260 on node 0
[ 0.245366] alloc kstat_irqs on node 0
[ 0.245370] cpu 7 spinlock event irq 2260
[ 0.245433] alloc irq_desc for 2259 on node 0
[ 0.245435] alloc kstat_irqs on node 0
[ 0.245439] alloc irq_desc for 2258 on node 0
[ 0.245440] alloc kstat_irqs on node 0
[ 0.245445] alloc irq_desc for 2257 on node 0
[ 0.245446] alloc kstat_irqs on node 0
[ 0.245450] alloc irq_desc for 2256 on node 0
[ 0.245451] alloc kstat_irqs on node 0
[ 0.000004] Initializing CPU#7
[ 0.000030] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.000032] CPU: L2 cache: 256K
[ 0.000033] CPU: L3 cache: 8192K
[ 0.000035] CPU 7/0x0 -> Node 0
[ 0.000037] CPU: Unsupported number of siblings 16
[ 0.245521] Brought up 8 CPUs
[ 0.245864] CPU0 attaching sched-domain:
[ 0.245867] domain 0: span 0-7 level CPU
[ 0.245869] groups: 0 1 2 3 4 5 6 7
[ 0.245879] CPU1 attaching sched-domain:
[ 0.245881] domain 0: span 0-7 level CPU
[ 0.245883] groups: 1 2 3 4 5 6 7 0
[ 0.245892] CPU2 attaching sched-domain:
[ 0.245894] domain 0: span 0-7 level CPU
[ 0.245896] groups: 2 3 4 5 6 7 0 1
[ 0.245905] CPU3 attaching sched-domain:
[ 0.245906] domain 0: span 0-7 level CPU
[ 0.245909] groups: 3 4 5 6 7 0 1 2
[ 0.245917] CPU4 attaching sched-domain:
[ 0.245919] domain 0: span 0-7 level CPU
[ 0.245921] groups: 4 5 6 7 0 1 2 3
[ 0.245930] CPU5 attaching sched-domain:
[ 0.245932] domain 0: span 0-7 level CPU
[ 0.245934] groups: 5 6 7 0 1 2 3 4
[ 0.245943] CPU6 attaching sched-domain:
[ 0.245945] domain 0: span 0-7 level CPU
[ 0.245947] groups: 6 7 0 1 2 3 4 5
[ 0.245956] CPU7 attaching sched-domain:
[ 0.245957] domain 0: span 0-7 level CPU
[ 0.245960] groups: 7 0 1 2 3 4 5 6
[ 0.246279] devtmpfs: initialized
[ 0.247479] Grant table initialized
[ 0.247530] regulator: core version 0.5
[ 0.247608] Time: 20:53:18 Date: 05/14/10
[ 0.247700] NET: Registered protocol family 16
[ 0.247791] alloc irq_desc for 2255 on node 0
[ 0.247793] alloc kstat_irqs on node 0
[ 0.247903] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.247977] ACPI: bus type pci registered
[ 0.248087] PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
[ 0.248143] PCI: MCFG area at f8000000 reserved in E820
[ 0.256477] PCI: Using MMCONFIG at f8000000 - fbffffff
[ 0.256529] PCI: Using configuration type 1 for base access
[ 0.257462] bio: create slab <bio-0> at 0
[ 0.259199] ERROR: Unable to locate IOAPIC for GSI 9
[ 0.259314] ACPI: EC: Look up EC in DSDT
[ 0.281724] ACPI: Interpreter enabled
[ 0.281777] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.281984] ACPI: Using IOAPIC for interrupt routing
[ 0.287661] ACPI Warning: Incorrect checksum in table [ ] - 1D, should be 61 (20090903/tbutils-314)
[ 0.287993] ACPI: No dock devices found.
[ 0.288632] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.288908] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.288965] pci 0000:00:01.0: PME# disabled
[ 0.289143] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[ 0.289200] pci 0000:00:03.0: PME# disabled
[ 0.289380] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
[ 0.289437] pci 0000:00:07.0: PME# disabled
[ 0.290110] pci 0000:00:19.0: reg 10 32bit mmio: [0xd2600000-0xd261ffff]
[ 0.290119] pci 0000:00:19.0: reg 14 32bit mmio: [0xd2622000-0xd2622fff]
[ 0.290129] pci 0000:00:19.0: reg 18 io port: [0x20e0-0x20ff]
[ 0.290198] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.290255] pci 0000:00:19.0: PME# disabled
[ 0.290388] pci 0000:00:1a.0: reg 20 io port: [0x20c0-0x20df]
[ 0.290507] pci 0000:00:1a.1: reg 20 io port: [0x20a0-0x20bf]
[ 0.290626] pci 0000:00:1a.2: reg 20 io port: [0x2080-0x209f]
[ 0.290750] pci 0000:00:1a.7: reg 10 32bit mmio: [0xd2621000-0xd26213ff]
[ 0.290841] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.290899] pci 0000:00:1a.7: PME# disabled
[ 0.291016] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf0000000-0xf0003fff]
[ 0.291091] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.291148] pci 0000:00:1b.0: PME# disabled
[ 0.291306] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.291363] pci 0000:00:1c.0: PME# disabled
[ 0.291523] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.291580] pci 0000:00:1c.1: PME# disabled
[ 0.291743] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.291800] pci 0000:00:1c.4: PME# disabled
[ 0.291943] pci 0000:00:1d.0: reg 20 io port: [0x2060-0x207f]
[ 0.292061] pci 0000:00:1d.1: reg 20 io port: [0x2040-0x205f]
[ 0.292178] pci 0000:00:1d.2: reg 20 io port: [0x2020-0x203f]
[ 0.292295] pci 0000:00:1d.7: reg 10 32bit mmio: [0xd2620000-0xd26203ff]
[ 0.292383] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.292440] pci 0000:00:1d.7: PME# disabled
[ 0.292696] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[ 0.292770] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
[ 0.292828] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
[ 0.292902] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f)
[ 0.293062] pci 0000:00:1f.2: reg 10 io port: [0x2158-0x215f]
[ 0.293071] pci 0000:00:1f.2: reg 14 io port: [0x216c-0x216f]
[ 0.293080] pci 0000:00:1f.2: reg 18 io port: [0x2150-0x2157]
[ 0.293089] pci 0000:00:1f.2: reg 1c io port: [0x2168-0x216b]
[ 0.293098] pci 0000:00:1f.2: reg 20 io port: [0x2130-0x213f]
[ 0.293107] pci 0000:00:1f.2: reg 24 io port: [0x2120-0x212f]
[ 0.293189] pci 0000:00:1f.3: reg 10 64bit mmio: [0xf0004000-0xf00040ff]
[ 0.293212] pci 0000:00:1f.3: reg 20 io port: [0x2000-0x201f]
[ 0.293288] pci 0000:00:1f.5: reg 10 io port: [0x2148-0x214f]
[ 0.293297] pci 0000:00:1f.5: reg 14 io port: [0x2164-0x2167]
[ 0.293306] pci 0000:00:1f.5: reg 18 io port: [0x2140-0x2147]
[ 0.293315] pci 0000:00:1f.5: reg 1c io port: [0x2160-0x2163]
[ 0.293324] pci 0000:00:1f.5: reg 20 io port: [0x2110-0x211f]
[ 0.293332] pci 0000:00:1f.5: reg 24 io port: [0x2100-0x210f]
[ 0.293545] pci 0000:01:00.0: supports D1 D2
[ 0.293617] pci 0000:00:01.0: bridge 32bit mmio: [0xd2500000-0xd25fffff]
[ 0.293690] pci 0000:02:00.0: reg 10 32bit mmio: [0xd2502000-0xd2502fff]
[ 0.293756] pci 0000:02:00.0: Disabling memory decoding and releasing memory resources.
[ 0.293867] pci 0000:02:00.0: supports D1 D2
[ 0.293869] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
[ 0.293927] pci 0000:02:00.0: PME# disabled
[ 0.294045] pci 0000:02:00.1: reg 10 32bit mmio: [0xd2501000-0xd2501fff]
[ 0.294112] pci 0000:02:00.1: Disabling memory decoding and releasing memory resources.
[ 0.294223] pci 0000:02:00.1: supports D1 D2
[ 0.294224] pci 0000:02:00.1: PME# supported from D0 D1 D2 D3hot
[ 0.294283] pci 0000:02:00.1: PME# disabled
[ 0.294400] pci 0000:02:00.2: reg 10 32bit mmio: [0xd2500000-0xd25000ff]
[ 0.294467] pci 0000:02:00.2: Disabling memory decoding and releasing memory resources.
[ 0.294546] pci 0000:02:00.2: Rounding up size of resource #0 to 0x1000.
[ 0.294632] pci 0000:02:00.2: supports D1 D2
[ 0.294633] pci 0000:02:00.2: PME# supported from D0 D1 D2 D3hot
[ 0.294692] pci 0000:02:00.2: PME# disabled
[ 0.294862] pci 0000:01:00.0: bridge 32bit mmio: [0xd2500000-0xd25fffff]
[ 0.295047] pci 0000:03:00.0: supports D1 D2
[ 0.295119] pci 0000:00:03.0: bridge 32bit mmio: [0xd2400000-0xd24fffff]
[ 0.295193] pci 0000:04:00.0: reg 10 32bit mmio: [0xd2402000-0xd2402fff]
[ 0.295294] pci 0000:04:00.0: supports D1 D2
[ 0.295296] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot
[ 0.295355] pci 0000:04:00.0: PME# disabled
[ 0.295473] pci 0000:04:00.1: reg 10 32bit mmio: [0xd2401000-0xd2401fff]
[ 0.295580] pci 0000:04:00.1: supports D1 D2
[ 0.295582] pci 0000:04:00.1: PME# supported from D0 D1 D2 D3hot
[ 0.295642] pci 0000:04:00.1: PME# disabled
[ 0.295761] pci 0000:04:00.2: reg 10 32bit mmio: [0xd2400000-0xd24000ff]
[ 0.295868] pci 0000:04:00.2: supports D1 D2
[ 0.295869] pci 0000:04:00.2: PME# supported from D0 D1 D2 D3hot
[ 0.295928] pci 0000:04:00.2: PME# disabled
[ 0.296097] pci 0000:03:00.0: bridge 32bit mmio: [0xd2400000-0xd24fffff]
[ 0.296167] pci 0000:05:00.0: reg 10 32bit mmio: [0xd1000000-0xd1ffffff]
[ 0.296182] pci 0000:05:00.0: reg 14 64bit mmio pref: [0xe0000000-0xefffffff]
[ 0.296196] pci 0000:05:00.0: reg 1c 64bit mmio: [0xd0000000-0xd0ffffff]
[ 0.296211] pci 0000:05:00.0: reg 30 32bit mmio pref: [0xfffe0000-0xffffffff]
[ 0.296309] pci 0000:00:07.0: bridge 32bit mmio: [0xd0000000-0xd1ffffff]
[ 0.296317] pci 0000:00:07.0: bridge 64bit mmio pref: [0xe0000000-0xefffffff]
[ 0.296542] pci 0000:06:00.0: supports D1 D2
[ 0.296637] pci 0000:00:1c.0: bridge 32bit mmio: [0xd2300000-0xd23fffff]
[ 0.296729] pci 0000:07:00.0: reg 10 32bit mmio: [0xd2302000-0xd2302fff]
[ 0.296863] pci 0000:07:00.0: supports D1 D2
[ 0.296865] pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot
[ 0.296926] pci 0000:07:00.0: PME# disabled
[ 0.297063] pci 0000:07:00.1: reg 10 32bit mmio: [0xd2301000-0xd2301fff]
[ 0.297198] pci 0000:07:00.1: supports D1 D2
[ 0.297199] pci 0000:07:00.1: PME# supported from D0 D1 D2 D3hot
[ 0.297260] pci 0000:07:00.1: PME# disabled
[ 0.297401] pci 0000:07:00.2: reg 10 32bit mmio: [0xd2300000-0xd23000ff]
[ 0.297535] pci 0000:07:00.2: supports D1 D2
[ 0.297537] pci 0000:07:00.2: PME# supported from D0 D1 D2 D3hot
[ 0.297597] pci 0000:07:00.2: PME# disabled
[ 0.297804] pci 0000:06:00.0: bridge 32bit mmio: [0xd2300000-0xd23fffff]
[ 0.298060] pci 0000:08:00.0: supports D1 D2
[ 0.298156] pci 0000:00:1c.1: bridge 32bit mmio: [0xd2200000-0xd22fffff]
[ 0.298251] pci 0000:09:00.0: reg 10 32bit mmio: [0xd2202000-0xd2202fff]
[ 0.298386] pci 0000:09:00.0: supports D1 D2
[ 0.298387] pci 0000:09:00.0: PME# supported from D0 D1 D2 D3hot
[ 0.298448] pci 0000:09:00.0: PME# disabled
[ 0.298586] pci 0000:09:00.1: reg 10 32bit mmio: [0xd2201000-0xd2201fff]
[ 0.298720] pci 0000:09:00.1: supports D1 D2
[ 0.298722] pci 0000:09:00.1: PME# supported from D0 D1 D2 D3hot
[ 0.298782] pci 0000:09:00.1: PME# disabled
[ 0.298921] pci 0000:09:00.2: reg 10 32bit mmio: [0xd2200000-0xd22000ff]
[ 0.299055] pci 0000:09:00.2: supports D1 D2
[ 0.299057] pci 0000:09:00.2: PME# supported from D0 D1 D2 D3hot
[ 0.299117] pci 0000:09:00.2: PME# disabled
[ 0.299326] pci 0000:08:00.0: bridge 32bit mmio: [0xd2200000-0xd22fffff]
[ 0.299423] pci 0000:0a:00.0: reg 10 io port: [0x1018-0x101f]
[ 0.299434] pci 0000:0a:00.0: reg 14 io port: [0x1024-0x1027]
[ 0.299445] pci 0000:0a:00.0: reg 18 io port: [0x1010-0x1017]
[ 0.299457] pci 0000:0a:00.0: reg 1c io port: [0x1020-0x1023]
[ 0.299469] pci 0000:0a:00.0: reg 20 io port: [0x1000-0x100f]
[ 0.299480] pci 0000:0a:00.0: reg 24 32bit mmio: [0xd2100000-0xd21003ff]
[ 0.299543] pci 0000:0a:00.0: supports D1
[ 0.299545] pci 0000:0a:00.0: PME# supported from D0 D1 D3hot
[ 0.299603] pci 0000:0a:00.0: PME# disabled
[ 0.299728] pci 0000:00:1c.4: bridge io port: [0x1000-0x1fff]
[ 0.299734] pci 0000:00:1c.4: bridge 32bit mmio: [0xd2100000-0xd21fffff]
[ 0.299801] pci 0000:0b:03.0: reg 10 32bit mmio: [0xd2004000-0xd20047ff]
[ 0.299812] pci 0000:0b:03.0: reg 14 32bit mmio: [0xd2000000-0xd2003fff]
[ 0.299883] pci 0000:0b:03.0: supports D1 D2
[ 0.299885] pci 0000:0b:03.0: PME# supported from D0 D1 D2 D3hot
[ 0.299942] pci 0000:0b:03.0: PME# disabled
[ 0.300056] pci 0000:00:1e.0: transparent bridge
[ 0.300114] pci 0000:00:1e.0: bridge 32bit mmio: [0xd2000000-0xd20fffff]
[ 0.300175] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.300876] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[ 0.301098] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT]
[ 0.301173] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT]
[ 0.301247] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT]
[ 0.301319] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 0.301392] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
[ 0.301472] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[ 0.315096] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.315626] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.316151] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.316670] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.317187] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.317705] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.318226] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.318744] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.319222] sync cpu 0 get result 1 max_id 7
[ 0.319229] sync cpu 1 get result 1 max_id 7
[ 0.319236] sync cpu 2 get result 1 max_id 7
[ 0.319245] sync cpu 3 get result 1 max_id 7
[ 0.319252] sync cpu 4 get result 1 max_id 7
[ 0.319258] sync cpu 5 get result 1 max_id 7
[ 0.319265] sync cpu 6 get result 1 max_id 7
[ 0.319271] sync cpu 7 get result 1 max_id 7
[ 0.319275] alloc irq_desc for 2254 on node 0
[ 0.319277] alloc kstat_irqs on node 0
[ 0.319299] xen_balloon: Initialising balloon driver with page order 0.
[ 0.319421] vgaarb: device added: PCI:0000:05:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.320859] vgaarb: loaded
[ 0.320992] SCSI subsystem initialized
[ 0.321238] libata version 3.00 loaded.
[ 0.321305] usbcore: registered new interface driver usbfs
[ 0.321366] usbcore: registered new interface driver hub
[ 0.321449] usbcore: registered new device driver usb
[ 0.321638] ACPI: WMI: Mapper loaded
[ 0.321688] PCI: Using ACPI for IRQ routing
[ 0.322065] NetLabel: Initializing
[ 0.322115] NetLabel: domain hash size = 128
[ 0.322165] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.322224] NetLabel: unlabeled traffic allowed by default
[ 0.322321] Switching to clocksource xen
[ 0.324085] pnp: PnP ACPI init
[ 0.324142] ACPI: bus type pnp registered
[ 0.325011] xen: registering gsi 8 triggering 1 polarity 0
[ 0.325013] xen_allocate_pirq: returning irq 8 for gsi 8
[ 0.325066] xen: --> irq=8
[ 0.325136] xen: registering gsi 13 triggering 1 polarity 0
[ 0.325138] xen_allocate_pirq: returning irq 13 for gsi 13
[ 0.325191] xen: --> irq=13
[ 0.326197] pnp: PnP ACPI: found 9 devices
[ 0.326248] ACPI: ACPI bus type pnp unregistered
[ 0.326305] system 00:05: ioport range 0x500-0x53f has been reserved
[ 0.326360] system 00:05: ioport range 0x400-0x47f has been reserved
[ 0.326415] system 00:05: ioport range 0x680-0x6ff has been reserved
[ 0.326582] pciback 0000:02:00.0: seizing device
[ 0.326636] pciback 0000:02:00.1: seizing device
[ 0.326693] pciback 0000:02:00.2: seizing device
[ 0.326746] pciback 0000:03:00.0: seizing device
[ 0.326800] pciback 0000:04:00.0: seizing device
[ 0.326854] pciback 0000:04:00.1: seizing device
[ 0.326907] pciback 0000:04:00.2: seizing device
[ 0.326997] pciback 0000:0b:03.0: seizing device
[ 0.330754] PM-Timer failed consistency check (0x0xffffff) - aborting.
[ 0.330830] pci 0000:05:00.0: BAR 6: no parent found for of device [0xfffe0000-0xffffffff]
[ 0.331077] pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
[ 0.331131] pci 0000:01:00.0: IO window: disabled
[ 0.331189] pci 0000:01:00.0: MEM window: 0xd2500000-0xd25fffff
[ 0.331247] pci 0000:01:00.0: PREFETCH window: disabled
[ 0.331308] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.331361] pci 0000:00:01.0: IO window: disabled
[ 0.331417] pci 0000:00:01.0: MEM window: 0xd2500000-0xd25fffff
[ 0.331474] pci 0000:00:01.0: PREFETCH window: disabled
[ 0.331533] pciback 0000:03:00.0: PCI bridge, secondary bus 0000:04
[ 0.331586] pciback 0000:03:00.0: IO window: disabled
[ 0.331645] pciback 0000:03:00.0: MEM window: 0xd2400000-0xd24fffff
[ 0.331704] pciback 0000:03:00.0: PREFETCH window: disabled
[ 0.331766] pci 0000:00:03.0: PCI bridge, secondary bus 0000:03
[ 0.331819] pci 0000:00:03.0: IO window: disabled
[ 0.331875] pci 0000:00:03.0: MEM window: 0xd2400000-0xd24fffff
[ 0.331932] pci 0000:00:03.0: PREFETCH window: disabled
[ 0.331991] pci 0000:05:00.0: BAR 6: can't allocate mem resource [0xf0000000-0xefffffff]
[ 0.332064] pci 0000:00:07.0: PCI bridge, secondary bus 0000:05
[ 0.332117] pci 0000:00:07.0: IO window: disabled
[ 0.332173] pci 0000:00:07.0: MEM window: 0xd0000000-0xd1ffffff
[ 0.332230] pci 0000:00:07.0: PREFETCH window: 0x000000e0000000-0x000000efffffff
[ 0.332308] pci 0000:06:00.0: PCI bridge, secondary bus 0000:07
[ 0.332361] pci 0000:06:00.0: IO window: disabled
[ 0.332422] pci 0000:06:00.0: MEM window: 0xd2300000-0xd23fffff
[ 0.332481] pci 0000:06:00.0: PREFETCH window: disabled
[ 0.332546] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:06
[ 0.332599] pci 0000:00:1c.0: IO window: disabled
[ 0.332656] pci 0000:00:1c.0: MEM window: 0xd2300000-0xd23fffff
[ 0.332713] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.332772] pci 0000:08:00.0: PCI bridge, secondary bus 0000:09
[ 0.332825] pci 0000:08:00.0: IO window: disabled
[ 0.332886] pci 0000:08:00.0: MEM window: 0xd2200000-0xd22fffff
[ 0.332945] pci 0000:08:00.0: PREFETCH window: disabled
[ 0.333010] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:08
[ 0.333063] pci 0000:00:1c.1: IO window: disabled
[ 0.333119] pci 0000:00:1c.1: MEM window: 0xd2200000-0xd22fffff
[ 0.333176] pci 0000:00:1c.1: PREFETCH window: disabled
[ 0.333235] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:0a
[ 0.333290] pci 0000:00:1c.4: IO window: 0x1000-0x1fff
[ 0.333347] pci 0000:00:1c.4: MEM window: 0xd2100000-0xd21fffff
[ 0.333404] pci 0000:00:1c.4: PREFETCH window: disabled
[ 0.333464] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:0b
[ 0.333517] pci 0000:00:1e.0: IO window: disabled
[ 0.333573] pci 0000:00:1e.0: MEM window: 0xd2000000-0xd20fffff
[ 0.333630] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.333698] xen: registering gsi 16 triggering 0 polarity 1
[ 0.333707] alloc irq_desc for 16 on node 0
[ 0.333709] alloc kstat_irqs on node 0
[ 0.333712] xen: --> irq=16
[ 0.333743] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.333802] pci 0000:00:01.0: setting latency timer to 64
[ 0.333819] pci 0000:01:00.0: setting latency timer to 64
[ 0.333831] xen: registering gsi 16 triggering 0 polarity 1
[ 0.333833] xen_allocate_pirq: returning irq 16 for gsi 16
[ 0.333885] xen: --> irq=16
[ 0.333887] Already setup the GSI :16
[ 0.333936] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.333994] pci 0000:00:03.0: setting latency timer to 64
[ 0.334011] pciback 0000:03:00.0: setting latency timer to 64
[ 0.334023] xen: registering gsi 16 triggering 0 polarity 1
[ 0.334025] xen_allocate_pirq: returning irq 16 for gsi 16
[ 0.334078] xen: --> irq=16
[ 0.334080] Already setup the GSI :16
[ 0.334129] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.334187] pci 0000:00:07.0: setting latency timer to 64
[ 0.334199] xen: registering gsi 17 triggering 0 polarity 1
[ 0.334203] alloc irq_desc for 17 on node 0
[ 0.334205] alloc kstat_irqs on node 0
[ 0.334207] xen: --> irq=17
[ 0.334237] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.334295] pci 0000:00:1c.0: setting latency timer to 64
[ 0.334318] pci 0000:06:00.0: setting latency timer to 64
[ 0.334331] xen: registering gsi 16 triggering 0 polarity 1
[ 0.334333] xen_allocate_pirq: returning irq 16 for gsi 16
[ 0.334385] xen: --> irq=16
[ 0.334387] Already setup the GSI :16
[ 0.334436] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.334495] pci 0000:00:1c.1: setting latency timer to 64
[ 0.334517] pci 0000:08:00.0: setting latency timer to 64
[ 0.334531] xen: registering gsi 17 triggering 0 polarity 1
[ 0.334532] xen_allocate_pirq: returning irq 17 for gsi 17
[ 0.334585] xen: --> irq=17
[ 0.334586] Already setup the GSI :17
[ 0.334636] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.334694] pci 0000:00:1c.4: setting latency timer to 64
[ 0.334704] pci 0000:00:1e.0: setting latency timer to 64
[ 0.334709] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.334711] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.334713] pci_bus 0000:01: resource 1 mem: [0xd2500000-0xd25fffff]
[ 0.334715] pci_bus 0000:02: resource 1 mem: [0xd2500000-0xd25fffff]
[ 0.334718] pci_bus 0000:03: resource 1 mem: [0xd2400000-0xd24fffff]
[ 0.334720] pci_bus 0000:04: resource 1 mem: [0xd2400000-0xd24fffff]
[ 0.334722] pci_bus 0000:05: resource 1 mem: [0xd0000000-0xd1ffffff]
[ 0.334724] pci_bus 0000:05: resource 2 pref mem [0xe0000000-0xefffffff]
[ 0.334726] pci_bus 0000:06: resource 1 mem: [0xd2300000-0xd23fffff]
[ 0.334729] pci_bus 0000:07: resource 1 mem: [0xd2300000-0xd23fffff]
[ 0.334731] pci_bus 0000:08: resource 1 mem: [0xd2200000-0xd22fffff]
[ 0.334733] pci_bus 0000:09: resource 1 mem: [0xd2200000-0xd22fffff]
[ 0.334735] pci_bus 0000:0a: resource 0 io: [0x1000-0x1fff]
[ 0.334737] pci_bus 0000:0a: resource 1 mem: [0xd2100000-0xd21fffff]
[ 0.334739] pci_bus 0000:0b: resource 1 mem: [0xd2000000-0xd20fffff]
[ 0.334741] pci_bus 0000:0b: resource 3 io: [0x00-0xffff]
[ 0.334743] pci_bus 0000:0b: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.334766] NET: Registered protocol family 2
[ 0.334960] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.335796] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.336604] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.336815] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.336871] TCP reno registered
[ 0.336994] NET: Registered protocol family 1
[ 0.337443] pci 0000:01:00.0: TI XIO2000a quirk detected; secondary bus fast back-to-back transfers disabled
[ 0.337539] pciback 0000:03:00.0: TI XIO2000a quirk detected; secondary bus fast back-to-back transfers disabled
[ 0.337690] pci 0000:05:00.0: Boot video device
[ 0.337693] pci 0000:06:00.0: TI XIO2000a quirk detected; secondary bus fast back-to-back transfers disabled
[ 0.337833] pci 0000:08:00.0: TI XIO2000a quirk detected; secondary bus fast back-to-back transfers disabled
[ 0.338016] Trying to unpack rootfs image as initramfs...
[ 0.454199] Freeing initrd memory: 230444k freed
[ 0.491457] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.491520] DMA: Placing 64MB software IO TLB between ffff880012016000 - ffff880016016000
[ 0.491593] DMA: software IO TLB at phys 0x12016000 - 0x16016000
[ 0.492163] Scanning for low memory corruption every 60 seconds
[ 0.492327] audit: initializing netlink socket (disabled)
[ 0.492389] type=2000 audit(1273870399.766:1): initialized
[ 0.499809] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.501106] VFS: Disk quotas dquot_6.5.2
[ 0.501205] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.501735] fuse init (API version 7.13)
[ 0.501854] msgmni has been set to 3870
[ 0.259594] alg: No test for stdrng (krng)
[ 0.502334] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.502407] io scheduler noop registered
[ 0.502456] io scheduler anticipatory registered
[ 0.502507] io scheduler deadline registered (default)
[ 0.502622] io scheduler cfq registered
[ 0.502907] alloc irq_desc for 2253 on node 0
[ 0.502909] alloc kstat_irqs on node 0
[ 0.502962] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.503142] alloc irq_desc for 2252 on node 0
[ 0.503144] alloc kstat_irqs on node 0
[ 0.503184] pcieport 0000:00:03.0: setting latency timer to 64
[ 0.503363] alloc irq_desc for 2251 on node 0
[ 0.503365] alloc kstat_irqs on node 0
[ 0.503405] pcieport 0000:00:07.0: setting latency timer to 64
[ 0.503567] alloc irq_desc for 2250 on node 0
[ 0.503569] alloc kstat_irqs on node 0
[ 0.503608] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.503764] alloc irq_desc for 2249 on node 0
[ 0.503766] alloc kstat_irqs on node 0
[ 0.503805] pcieport 0000:00:1c.1: setting latency timer to 64
[ 0.503961] alloc irq_desc for 2248 on node 0
[ 0.503962] alloc kstat_irqs on node 0
[ 0.504002] pcieport 0000:00:1c.4: setting latency timer to 64
[ 0.504598] aer 0000:00:01.0:pcie02: service driver aer loaded
[ 0.504668] aer 0000:00:03.0:pcie02: service driver aer loaded
[ 0.504735] aer 0000:00:07.0:pcie02: service driver aer loaded
[ 0.504744] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.504816] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.504978] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[ 0.505057] ACPI: Sleep Button [SLPB]
[ 0.505146] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.505218] ACPI: Power Button [PWRF]
[ 0.510481] [Firmware Bug]: ACPI: Invalid BIOS _PSS frequency: 0x80000000 MHz
[ 0.510540] [Firmware Bug]: BIOS needs update for CPU frequency support
[ 0.510599] processor: probe of LNXCPU:08 failed with error -14
[ 0.511100] [Firmware Bug]: ACPI: Invalid BIOS _PSS frequency: 0x80000000 MHz
[ 0.511157] [Firmware Bug]: BIOS needs update for CPU frequency support
[ 0.511214] processor: probe of LNXCPU:09 failed with error -14
[ 0.511709] [Firmware Bug]: ACPI: Invalid BIOS _PSS frequency: 0x80000000 MHz
[ 0.511767] [Firmware Bug]: BIOS needs update for CPU frequency support
[ 0.511824] processor: probe of LNXCPU:0a failed with error -14
[ 0.512320] [Firmware Bug]: ACPI: Invalid BIOS _PSS frequency: 0x80000000 MHz
[ 0.512377] [Firmware Bug]: BIOS needs update for CPU frequency support
[ 0.512434] processor: probe of LNXCPU:0b failed with error -14
[ 0.512939] [Firmware Bug]: ACPI: Invalid BIOS _PSS frequency: 0x80000000 MHz
[ 0.512997] [Firmware Bug]: BIOS needs update for CPU frequency support
[ 0.513055] processor: probe of LNXCPU:0c failed with error -14
[ 0.513550] [Firmware Bug]: ACPI: Invalid BIOS _PSS frequency: 0x80000000 MHz
[ 0.513608] [Firmware Bug]: BIOS needs update for CPU frequency support
[ 0.513665] processor: probe of LNXCPU:0d failed with error -14
[ 0.514159] [Firmware Bug]: ACPI: Invalid BIOS _PSS frequency: 0x80000000 MHz
[ 0.514217] [Firmware Bug]: BIOS needs update for CPU frequency support
[ 0.514274] processor: probe of LNXCPU:0e failed with error -14
[ 0.514766] [Firmware Bug]: ACPI: Invalid BIOS _PSS frequency: 0x80000000 MHz
[ 0.514823] [Firmware Bug]: BIOS needs update for CPU frequency support
[ 0.514880] processor: probe of LNXCPU:0f failed with error -14
[ 0.516894] Event-channel device installed.
[ 0.517001] xen: registering gsi 19 triggering 0 polarity 1
[ 0.517011] alloc irq_desc for 19 on node 0
[ 0.517013] alloc kstat_irqs on node 0
[ 0.517016] xen: --> irq=19
[ 0.517048] pciback 0000:0b:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 0.517110] pciback 0000:0b:03.0: PCI INT A disabled
[ 0.517205] xen: registering gsi 18 triggering 0 polarity 1
[ 0.517210] alloc irq_desc for 18 on node 0
[ 0.517211] alloc kstat_irqs on node 0
[ 0.517214] xen: --> irq=18
[ 0.517243] pciback 0000:04:00.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.517306] pciback 0000:04:00.2: PCI INT C disabled
[ 0.517397] xen: registering gsi 17 triggering 0 polarity 1
[ 0.517399] xen_allocate_pirq: returning irq 17 for gsi 17
[ 0.517452] xen: --> irq=17
[ 0.517454] Already setup the GSI :17
[ 0.517503] pciback 0000:04:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.517565] pciback 0000:04:00.1: PCI INT B disabled
[ 0.517657] xen: registering gsi 16 triggering 0 polarity 1
[ 0.517659] xen_allocate_pirq: returning irq 16 for gsi 16
[ 0.517711] xen: --> irq=16
[ 0.517713] Already setup the GSI :16
[ 0.517762] pciback 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.517824] pciback 0000:04:00.0: PCI INT A disabled
[ 0.517957] pciback 0000:02:00.2: enabling device (0014 -> 0016)
[ 0.518014] xen: registering gsi 18 triggering 0 polarity 1
[ 0.518016] xen_allocate_pirq: returning irq 18 for gsi 18
[ 0.518069] xen: --> irq=18
[ 0.518070] Already setup the GSI :18
[ 0.518120] pciback 0000:02:00.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.518181] pciback 0000:02:00.2: PCI INT C disabled
[ 0.519635] pciback 0000:02:00.1: enabling device (0014 -> 0016)
[ 0.519692] xen: registering gsi 17 triggering 0 polarity 1
[ 0.519694] xen_allocate_pirq: returning irq 17 for gsi 17
[ 0.519746] xen: --> irq=17
[ 0.519748] Already setup the GSI :17
[ 0.519797] pciback 0000:02:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.519858] pciback 0000:02:00.1: PCI INT B disabled
[ 0.519951] pciback 0000:02:00.0: enabling device (0014 -> 0016)
[ 0.520008] xen: registering gsi 16 triggering 0 polarity 1
[ 0.520010] xen_allocate_pirq: returning irq 16 for gsi 16
[ 0.520062] xen: --> irq=16
[ 0.520064] Already setup the GSI :16
[ 0.520113] pciback 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.520175] pciback 0000:02:00.0: PCI INT A disabled
[ 0.522747] blktap_device_init: blktap device major 253
[ 0.522806] blktap_ring_init: blktap ring major: 252
[ 0.523300] registering netback
[ 0.523382] xen-platform-pcifailed backend handshake: unrecognised magic value
[ 0.523465] alloc irq_desc for 2247 on node 0
[ 0.523467] alloc kstat_irqs on node 0
[ 0.524366] alloc irq_desc for 2246 on node 0
[ 0.524368] alloc kstat_irqs on node 0
[ 0.524620] hpet_acpi_add: no address or irqs in _CRS
[ 0.524682] Linux agpgart interface v0.103
[ 0.524734] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.524927] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
[ 0.525900] brd: module loaded
[ 0.526305] loop: module loaded
[ 0.526425] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.526586] ata_piix 0000:00:1f.2: version 2.13
[ 0.526605] xen: registering gsi 19 triggering 0 polarity 1
[ 0.526607] xen_allocate_pirq: returning irq 19 for gsi 19
[ 0.526659] xen: --> irq=19
[ 0.526663] Already setup the GSI :19
[ 0.526711] ata_piix 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 0.526771] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 0.526999] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.527122] scsi0 : ata_piix
[ 0.527236] scsi1 : ata_piix
[ 0.527459] ata1: SATA max UDMA/133 cmd 0x2158 ctl 0x216c bmdma 0x2130 irq 19
[ 0.527519] ata2: SATA max UDMA/133 cmd 0x2150 ctl 0x2168 bmdma 0x2138 irq 19
[ 0.527595] xen: registering gsi 18 triggering 0 polarity 1
[ 0.527597] xen_allocate_pirq: returning irq 18 for gsi 18
[ 0.527649] xen: --> irq=18
[ 0.527651] Already setup the GSI :18
[ 0.527700] ata_piix 0000:00:1f.5: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 0.527759] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 0.527976] ata_piix 0000:00:1f.5: setting latency timer to 64
[ 0.528097] scsi2 : ata_piix
[ 0.528200] scsi3 : ata_piix
[ 0.528355] ata3: SATA max UDMA/133 cmd 0x2148 ctl 0x2164 bmdma 0x2110 irq 18
[ 0.528413] ata4: SATA max UDMA/133 cmd 0x2140 ctl 0x2160 bmdma 0x2118 irq 18
[ 0.528534] xen: registering gsi 16 triggering 0 polarity 1
[ 0.528536] xen_allocate_pirq: returning irq 16 for gsi 16
[ 0.528588] xen: --> irq=16
[ 0.528590] Already setup the GSI :16
[ 0.528639] pata_acpi 0000:0a:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.528730] pata_acpi 0000:0a:00.0: setting latency timer to 64
[ 0.528745] pata_acpi 0000:0a:00.0: PCI INT A disabled
[ 0.529011] Fixed MDIO Bus: probed
[ 0.529082] PPP generic driver version 2.4.2
[ 0.529158] tun: Universal TUN/TAP device driver, 1.6
[ 0.529209] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.529327] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.529399] xen: registering gsi 18 triggering 0 polarity 1
[ 0.529401] xen_allocate_pirq: returning irq 18 for gsi 18
[ 0.529453] xen: --> irq=18
[ 0.529455] Already setup the GSI :18
[ 0.529503] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.529569] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 0.529574] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 0.529653] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 0.529762] ehci_hcd 0000:00:1a.7: debug port 1
[ 0.533692] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 0.533697] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xd2621000
[ 0.552543] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 0.552723] usb usb1: configuration #1 chosen from 1 choice
[ 0.552822] hub 1-0:1.0: USB hub found
[ 0.552904] hub 1-0:1.0: 6 ports detected
[ 0.553055] xen: registering gsi 23 triggering 0 polarity 1
[ 0.553066] alloc irq_desc for 23 on node 0
[ 0.553069] alloc kstat_irqs on node 0
[ 0.553074] xen: --> irq=23
[ 0.553109] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.553197] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.553203] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.553314] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 0.553453] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.557407] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.557474] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd2620000
[ 0.572543] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.572742] usb usb2: configuration #1 chosen from 1 choice
[ 0.572840] hub 2-0:1.0: USB hub found
[ 0.572920] hub 2-0:1.0: 6 ports detected
[ 0.573073] xen: registering gsi 18 triggering 0 polarity 1
[ 0.573077] xen_allocate_pirq: returning irq 18 for gsi 18
[ 0.573142] xen: --> irq=18
[ 0.573146] Already setup the GSI :18
[ 0.573207] ehci_hcd 0000:07:00.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.573296] ehci_hcd 0000:07:00.2: EHCI Host Controller
[ 0.573407] ehci_hcd 0000:07:00.2: new USB bus registered, assigned bus number 3
[ 0.602553] ehci_hcd 0000:07:00.2: irq 18, io mem 0xd2300000
[ 0.622538] ehci_hcd 0000:07:00.2: USB 2.0 started, EHCI 1.00
[ 0.622698] usb usb3: configuration #1 chosen from 1 choice
[ 0.622799] hub 3-0:1.0: USB hub found
[ 0.622876] hub 3-0:1.0: 5 ports detected
[ 0.623031] xen: registering gsi 19 triggering 0 polarity 1
[ 0.623035] xen_allocate_pirq: returning irq 19 for gsi 19
[ 0.623099] xen: --> irq=19
[ 0.623103] Already setup the GSI :19
[ 0.623165] ehci_hcd 0000:09:00.2: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[ 0.623253] ehci_hcd 0000:09:00.2: EHCI Host Controller
[ 0.623365] ehci_hcd 0000:09:00.2: new USB bus registered, assigned bus number 4
[ 0.652580] ehci_hcd 0000:09:00.2: irq 19, io mem 0xd2200000
[ 0.672568] ehci_hcd 0000:09:00.2: USB 2.0 started, EHCI 1.00
[ 0.672727] usb usb4: configuration #1 chosen from 1 choice
[ 0.672828] hub 4-0:1.0: USB hub found
[ 0.672906] hub 4-0:1.0: 5 ports detected
[ 0.673049] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.673157] xen: registering gsi 16 triggering 0 polarity 1
[ 0.673161] xen_allocate_pirq: returning irq 16 for gsi 16
[ 0.673225] xen: --> irq=16
[ 0.673229] Already setup the GSI :16
[ 0.673290] ohci_hcd 0000:07:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.673379] ohci_hcd 0000:07:00.0: OHCI Host Controller
[ 0.673490] ohci_hcd 0000:07:00.0: new USB bus registered, assigned bus number 5
[ 0.673663] ohci_hcd 0000:07:00.0: irq 16, io mem 0xd2302000
[ 0.762602] usb usb5: configuration #1 chosen from 1 choice
[ 0.762676] hub 5-0:1.0: USB hub found
[ 0.762739] hub 5-0:1.0: 3 ports detected
[ 0.762845] xen: registering gsi 17 triggering 0 polarity 1
[ 0.762847] xen_allocate_pirq: returning irq 17 for gsi 17
[ 0.762899] xen: --> irq=17
[ 0.762901] Already setup the GSI :17
[ 0.762950] ohci_hcd 0000:07:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.763021] ohci_hcd 0000:07:00.1: OHCI Host Controller
[ 0.763098] ohci_hcd 0000:07:00.1: new USB bus registered, assigned bus number 6
[ 0.763237] ohci_hcd 0000:07:00.1: irq 17, io mem 0xd2301000
[ 0.852620] usb usb6: configuration #1 chosen from 1 choice
[ 0.852691] hub 6-0:1.0: USB hub found
[ 0.852754] hub 6-0:1.0: 2 ports detected
[ 0.852860] xen: registering gsi 17 triggering 0 polarity 1
[ 0.852863] xen_allocate_pirq: returning irq 17 for gsi 17
[ 0.852914] xen: --> irq=17
[ 0.852916] Already setup the GSI :17
[ 0.852965] ohci_hcd 0000:09:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.853035] ohci_hcd 0000:09:00.0: OHCI Host Controller
[ 0.853112] ohci_hcd 0000:09:00.0: new USB bus registered, assigned bus number 7
[ 0.853198] ohci_hcd 0000:09:00.0: irq 17, io mem 0xd2202000
[ 0.884416] ata3: SATA link down (SStatus 0 SControl 300)
[ 0.896230] ata4: SATA link down (SStatus 0 SControl 300)
[ 0.942617] usb usb7: configuration #1 chosen from 1 choice
[ 0.942688] hub 7-0:1.0: USB hub found
[ 0.942753] hub 7-0:1.0: 3 ports detected
[ 0.942860] xen: registering gsi 18 triggering 0 polarity 1
[ 0.942862] xen_allocate_pirq: returning irq 18 for gsi 18
[ 0.942914] xen: --> irq=18
[ 0.942916] Already setup the GSI :18
[ 0.942965] ohci_hcd 0000:09:00.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 0.943035] ohci_hcd 0000:09:00.1: OHCI Host Controller
[ 0.943111] ohci_hcd 0000:09:00.1: new USB bus registered, assigned bus number 8
[ 0.943198] ohci_hcd 0000:09:00.1: irq 18, io mem 0xd2201000
[ 1.032597] usb usb8: configuration #1 chosen from 1 choice
[ 1.032668] hub 8-0:1.0: USB hub found
[ 1.032731] hub 8-0:1.0: 2 ports detected
[ 1.032823] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.032894] xen: registering gsi 16 triggering 0 polarity 1
[ 1.032896] xen_allocate_pirq: returning irq 16 for gsi 16
[ 1.032948] xen: --> irq=16
[ 1.032950] Already setup the GSI :16
[ 1.032999] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.033060] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 1.033064] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.033144] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 9
[ 1.033242] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020c0
[ 1.033376] usb usb9: configuration #1 chosen from 1 choice
[ 1.033448] hub 9-0:1.0: USB hub found
[ 1.033504] hub 9-0:1.0: 2 ports detected
[ 1.033595] xen: registering gsi 21 triggering 0 polarity 1
[ 1.033600] alloc irq_desc for 21 on node 0
[ 1.033602] alloc kstat_irqs on node 0
[ 1.033605] xen: --> irq=21
[ 1.033635] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 1.033696] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 1.033700] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.033783] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 10
[ 1.033934] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020a0
[ 1.034068] usb usb10: configuration #1 chosen from 1 choice
[ 1.034138] hub 10-0:1.0: USB hub found
[ 1.034194] hub 10-0:1.0: 2 ports detected
[ 1.034286] xen: registering gsi 19 triggering 0 polarity 1
[ 1.034288] xen_allocate_pirq: returning irq 19 for gsi 19
[ 1.034339] xen: --> irq=19
[ 1.034341] Already setup the GSI :19
[ 1.034390] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 1.034450] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 1.034454] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 1.034531] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 11
[ 1.034631] uhci_hcd 0000:00:1a.2: irq 19, io base 0x00002080
[ 1.034764] usb usb11: configuration #1 chosen from 1 choice
[ 1.034836] hub 11-0:1.0: USB hub found
[ 1.034893] hub 11-0:1.0: 2 ports detected
[ 1.034982] xen: registering gsi 23 triggering 0 polarity 1
[ 1.034984] xen_allocate_pirq: returning irq 23 for gsi 23
[ 1.035036] xen: --> irq=23
[ 1.035038] Already setup the GSI :23
[ 1.035087] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.035147] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.035151] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.035226] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 12
[ 1.035324] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002060
[ 1.035461] usb usb12: configuration #1 chosen from 1 choice
[ 1.035533] hub 12-0:1.0: USB hub found
[ 1.035590] hub 12-0:1.0: 2 ports detected
[ 1.035680] xen: registering gsi 19 triggering 0 polarity 1
[ 1.035682] xen_allocate_pirq: returning irq 19 for gsi 19
[ 1.035733] xen: --> irq=19
[ 1.035736] Already setup the GSI :19
[ 1.035784] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.035844] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.035848] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.035924] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 13
[ 1.037379] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002040
[ 1.037514] usb usb13: configuration #1 chosen from 1 choice
[ 1.037585] hub 13-0:1.0: USB hub found
[ 1.037641] hub 13-0:1.0: 2 ports detected
[ 1.037730] xen: registering gsi 18 triggering 0 polarity 1
[ 1.037732] xen_allocate_pirq: returning irq 18 for gsi 18
[ 1.037784] xen: --> irq=18
[ 1.037786] Already setup the GSI :18
[ 1.037835] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.037895] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.037899] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.037978] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 14
[ 1.038076] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002020
[ 1.038211] usb usb14: configuration #1 chosen from 1 choice
[ 1.038282] hub 14-0:1.0: USB hub found
[ 1.038339] hub 14-0:1.0: 2 ports detected
[ 1.038460] PNP: No PS/2 controller found. Probing ports directly.
[ 1.041586] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.041641] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.041760] mice: PS/2 mouse device common for all mice
[ 1.041887] rtc_cmos 00:02: RTC can wake from S4
[ 1.041966] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 1.042089] rtc0: alarms up to one month, y3k, 114 bytes nvram
[ 1.042148] md: raid1 personality registered for level 1
[ 1.042277] device-mapper: uevent: version 1.0.3
[ 1.042411] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 1.042708] device-mapper: multipath: version 1.1.0 loaded
[ 1.042762] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.043228] cpuidle: using governor ladder
[ 1.043282] cpuidle: using governor menu
[ 1.043621] TCP cubic registered
[ 1.043757] NET: Registered protocol family 10
[ 1.044204] lo: Disabled Privacy Extensions
[ 1.044471] NET: Registered protocol family 17
[ 1.044651] PM: Resume from disk failed.
[ 1.044660] registered taskstats version 1
[ 1.045994] Magic number: 10:506:902
[ 1.046113] rtc_cmos 00:02: setting system clock to 2010-05-14 20:53:19 UTC (1273870399)
[ 1.046186] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.046238] EDD information not available.
[ 1.352495] usb 14-1: new full speed USB device using uhci_hcd and address 2
[ 1.402593] ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.402682] ata2.01: SATA link down (SStatus 0 SControl 300)
[ 1.403005] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.403097] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.423775] ata2.00: ATA-8: WDC WD2502ABYS-02B7A0, 02.03B03, max UDMA/133
[ 1.423844] ata2.00: 490350672 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.443718] ata1.00: ATA-8: WDC WD2502ABYS-02B7A0, 02.03B03, max UDMA/133
[ 1.443787] ata1.00: 490350672 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.443881] ata1.01: ATAPI: PIONEER DVD-RW DVR-218L, 1.02, max UDMA/100
[ 1.463820] ata2.00: configured for UDMA/133
[ 1.483769] ata1.00: configured for UDMA/133
[ 1.522772] ata1.01: configured for UDMA/100
[ 1.282953] scsi 0:0:0:0: Direct-Access ATA WDC WD2502ABYS-0 02.0 PQ: 0 ANSI: 5
[ 1.283221] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.282305] sd 0:0:0:0: [sda] 490350672 512-byte logical blocks: (251 GB/233 GiB)
[ 1.282392] sd 0:0:0:0: [sda] Write Protect is off
[ 1.282397] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.282440] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.287803] scsi 0:0:1:0: CD-ROM PIONEER DVD-RW DVR-218L 1.02 PQ: 0 ANSI: 5
[ 1.286847] sda:
[ 1.537220] usb 14-1: configuration #1 chosen from 1 choice
[ 1.538897] sda1 sda2 sda3
[ 1.539269] hub 14-1:1.0: USB hub found
[ 1.541146] hub 14-1:1.0: 3 ports detected
[ 1.314108] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.314197] Uniform CD-ROM driver Revision: 3.20
[ 1.556319] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.314421] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 1.314478] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 1.556796] scsi 1:0:0:0: Direct-Access ATA WDC WD2502ABYS-0 02.0 PQ: 0 ANSI: 5
[ 1.314917] sd 1:0:0:0: [sdb] 490350672 512-byte logical blocks: (251 GB/233 GiB)
[ 1.557040] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 1.315154] sd 1:0:0:0: [sdb] Write Protect is off
[ 1.315219] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.315264] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.315573] sdb: sdb1 sdb2 sdb3
[ 1.568532] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1.568726] Freeing unused kernel memory: 816k freed
[ 1.568956] Write protecting the kernel read-only data: 7904k
[ 1.864075] usb 14-1.1: new full speed USB device using uhci_hcd and address 3
[ 2.056045] usb 14-1.1: configuration #1 chosen from 1 choice
[ 1.818189] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
[ 1.818245] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[ 1.818344] xen: registering gsi 20 triggering 0 polarity 1
[ 1.818354] alloc irq_desc for 20 on node 0
[ 1.818356] alloc kstat_irqs on node 0
[ 1.818359] xen: --> irq=20
[ 1.818393] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.818456] e1000e 0000:00:19.0: setting latency timer to 64
[ 1.818582] alloc irq_desc for 2245 on node 0
[ 1.818583] alloc kstat_irqs on node 0
[ 1.849345] ahci 0000:0a:00.0: version 3.0
[ 1.850758] xen: registering gsi 16 triggering 0 polarity 1
[ 1.850760] xen_allocate_pirq: returning irq 16 for gsi 16
[ 1.850820] xen: --> irq=16
[ 1.850824] Already setup the GSI :16
[ 1.850876] pata_marvell 0000:0a:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.850975] pata_marvell 0000:0a:00.0: setting latency timer to 64
[ 1.851053] scsi4 : pata_marvell
[ 1.851160] scsi5 : pata_marvell
[ 1.851235] ata5: PATA max UDMA/100 cmd 0x1018 ctl 0x1024 bmdma 0x1000 irq 16
[ 1.851294] ata6: PATA max UDMA/133 cmd 0x1010 ctl 0x1020 bmdma 0x1008 irq 16
[ 2.224891] 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1c:c0:b2:11:1d
[ 2.224975] 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[ 2.225062] 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: ffffff-0ff
[ 2.246745] usbcore: registered new interface driver hiddev
[ 2.249535] input: Mitsumi Electric Apple Extended USB Keyboard as /devices/pci0000:00/0000:00:1d.2/usb14/14-1/14-1.1/14-1.1:1.0/input/input3
[ 2.249675] generic-usb 0003:05AC:0204.0001: input,hidraw0: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0000:00:1d.2-1.1/input0
[ 2.253398] input: Mitsumi Electric Apple Extended USB Keyboard as /devices/pci0000:00/0000:00:1d.2/usb14/14-1/14-1.1/14-1.1:1.1/input/input4
[ 2.253521] generic-usb 0003:05AC:0204.0002: input,hidraw1: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0000:00:1d.2-1.1/input1
[ 2.253632] usbcore: registered new interface driver usbhid
[ 2.253684] usbhid: v2.6:USB HID core driver
[ 2.370330] md: raid0 personality registered for level 0
[ 2.397129] md: md0 stopped.
[ 2.653428] md: bind<sdb1>
[ 2.653683] md: bind<sda1>
[ 2.660556] raid1: raid set md0 active with 2 out of 2 mirrors
[ 2.660635] md0: detected capacity change from 0 to 8003059712
[ 2.660990] md: md1 stopped.
[ 2.661138] md0: unknown partition table
[ 2.714120] md: bind<sdb2>
[ 2.714414] md: bind<sda2>
[ 2.723526] raid1: raid set md1 active with 2 out of 2 mirrors
[ 2.723618] md1: detected capacity change from 0 to 241000579072
[ 2.724126] md: md2 stopped.
[ 2.724356] md1: unknown partition table
[ 2.769574] md: bind<sdb3>
[ 2.773297] md: bind<sda3>
[ 2.783028] raid0: looking at sda3
[ 2.783092] raid0: comparing sda3(4000000)
[ 2.783137] with sda3(4000000)
[ 2.783246] raid0: END
[ 2.783304] raid0: ==> UNIQUE
[ 2.783363] raid0: 1 zones
[ 2.783421] raid0: looking at sdb3
[ 2.783481] raid0: comparing sdb3(4000000)
[ 2.783526] with sda3(4000000)
[ 2.783635] raid0: EQUAL
[ 2.783693] raid0: FINAL 1 zones
[ 2.783754] raid0: done.
[ 2.783812] raid0 : md_size is 8000000 sectors.
[ 2.783874] ******* md2 configuration *********
[ 2.783936] zone0=[sda3/sdb3/]
[ 2.784101] zone offset=0kb device offset=0kb size=4000000kb
[ 2.784167] **********************************
[ 2.784168]
[ 2.784290] md2: detected capacity change from 0 to 4096000000
[ 2.784732] md2: unknown partition table
[ 2.660667] PM: Starting manual resume from disk
[ 2.660718] PM: Resume from partition 9:2
[ 2.660720] PM: Checking hibernation image.
[ 2.904980] PM: Error -22 checking image file
[ 2.904982] PM: Resume from disk failed.
[ 2.711245] kjournald starting. Commit interval 5 seconds
[ 2.956568] EXT3-fs: mounted filesystem with ordered data mode.
[ 3.740403] udevd version 125 started
[ 4.738670] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 5.071182] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 5.087723] xen: registering gsi 18 triggering 0 polarity 1
[ 5.087726] xen_allocate_pirq: returning irq 18 for gsi 18
[ 5.087781] xen: --> irq=18
[ 5.087785] Already setup the GSI :18
[ 5.087836] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 5.112451] xen: registering gsi 22 triggering 0 polarity 1
[ 5.112461] alloc irq_desc for 22 on node 0
[ 5.112463] alloc kstat_irqs on node 0
[ 5.112466] xen: --> irq=22
[ 5.112499] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 5.112665] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 5.122022] Error: Driver 'pcspkr' is already registered, aborting...
[ 5.262265] Error: Driver 'pcspkr' is already registered, aborting...
[ 5.516255] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6
[ 6.390738] Adding 3999992k swap on /dev/md2. Priority:-1 extents:1 across:3999992k
[ 6.500494] EXT3 FS on md0, internal journal
[ 9.952882] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.666735] Bridge firewalling registered
[ 12.092219] ADDRCONF(NETDEV_UP): peth0: link is not ready
[ 16.062225] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 16.062785] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready
[ 15.917421] device peth0 entered promiscuous mode
[ 15.955423] eth0: port 1(peth0) entering forwarding state
[ 19.537450] alloc irq_desc for 2244 on node 0
[ 19.537454] alloc kstat_irqs on node 0
[ 19.537511] alloc irq_desc for 2243 on node 0
[ 19.537515] alloc kstat_irqs on node 0
[ 19.765345] XENBUS: Unable to read cpu state
[ 19.765616] XENBUS: Unable to read cpu state
[ 19.765859] XENBUS: Unable to read cpu state
[ 19.766134] XENBUS: Unable to read cpu state
[ 19.768061] XENBUS: Unable to read cpu state
[ 19.768340] XENBUS: Unable to read cpu state
[ 19.768593] XENBUS: Unable to read cpu state
[ 19.768823] XENBUS: Unable to read cpu state
[ 22.803502] alloc irq_desc for 2242 on node 0
[ 22.803505] alloc kstat_irqs on node 0
02:00.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d2500000 (32-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pciback
02:00.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 0: Memory at d2501000 (32-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pciback
02:00.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at d2502000 (32-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pciback
[-- Attachment #4: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
next prev parent reply other threads:[~2010-05-14 21:17 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <AANLkTingpLEP-MzziwzAKBJfNCzIwPiExwJGsVvzy7Bb@mail.gmail.com>
[not found] ` <AANLkTimVFTsfWR62doUMZOIlMCVBAVJioscvRzUBbIPD@mail.gmail.com>
[not found] ` <20100513122939.GB17817@reaktio.net>
[not found] ` <AANLkTinCxjsORy7_LUAeZPQoGllg4TcVQeym9cf7rn5S@mail.gmail.com>
[not found] ` <20100513141417.GT17817@reaktio.net>
[not found] ` <AANLkTilIotxoc6GE22WGlInpcm1BJmj72QSumIPU4oR2@mail.gmail.com>
[not found] ` <20100513154728.GV17817@reaktio.net>
[not found] ` <AANLkTilQPnVdBEY8jSDWh-Y--vqugPDqGAE-k41IU_rB@mail.gmail.com>
[not found] ` <20100513175808.GD17817@reaktio.net>
[not found] ` <AANLkTimKlhHnJ70MSbtniRbj6EirU-0BnT259Smgv_rb@mail.gmail.com>
2010-05-13 18:10 ` [Xen-users] xen/stable-2.6.32.x compilation failure in do_hvm_suspend() Pasi Kärkkäinen
2010-05-13 18:22 ` Dan Magenheimer
2010-05-13 18:32 ` M A Young
2010-05-13 18:37 ` [Xen-devel] " chris
2010-05-13 18:44 ` Re: [Xen-users] " M A Young
2010-05-13 18:50 ` chris
2010-05-14 14:45 ` chris
[not found] ` <4BED8925.8010405@interface-tech.com>
2010-05-14 17:41 ` chris
2010-05-14 18:51 ` Pasi Kärkkäinen
2010-05-14 18:53 ` Pierre POMES
2010-05-14 19:15 ` Pasi Kärkkäinen
2010-05-14 19:43 ` [Xen-devel] " Pierre POMES
2010-05-13 18:28 ` [Xen-users] RE: Xen4 / Intel DX58SO Mobo / VT-d not working chris
2010-05-14 19:05 ` chris
2010-05-14 19:11 ` Pasi Kärkkäinen
2010-05-14 19:18 ` [Xen-users] " chris
2010-05-14 19:21 ` Pasi Kärkkäinen
2010-05-14 19:46 ` [Xen-users] " chris
2010-05-14 20:39 ` chris
2010-05-14 20:50 ` Pasi Kärkkäinen
2010-05-14 21:17 ` chris [this message]
2010-05-16 7:36 ` [Xen-devel] " Han, Weidong
2010-05-16 13:00 ` chris
2010-05-17 17:05 ` chris
2010-05-18 9:31 ` Re: [Xen-users] " Weidong Han
2010-05-21 19:41 ` chris
2010-05-24 2:54 ` [Xen-devel] " Weidong Han
2010-05-14 21:25 ` Re: [Xen-users] " Sander Eikelenboom
2010-05-14 21:26 ` chris
2010-05-14 21:34 ` Pasi Kärkkäinen
2010-05-14 21:57 ` chris
2010-05-15 6:56 ` Sander Eikelenboom
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=AANLkTinL35-_rYMMAhNLoxhORR615ag5oUv7_bNrG3a9@mail.gmail.com \
--to=tknchris@gmail.com \
--cc=pasik@iki.fi \
--cc=xen-devel@lists.xensource.com \
--cc=xen-users@lists.xensource.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).