From: Safa Hamza <safahamza1@gmail.com>
To: xen-devel@lists.xenproject.org
Subject: help
Date: Thu, 10 Mar 2016 21:04:22 +0100 [thread overview]
Message-ID: <CAFwQ9hHz9qDo10=apqsWWBuZitT5TGf0OB0LoTTOTXXXz8c-yQ@mail.gmail.com> (raw)
[-- Attachment #1.1: Type: text/plain, Size: 6600 bytes --]
hello
i'm trying to run xen on omap5 following
this
http://wiki.xenproject.org/wiki/Xen_ARM_with_Virtualization_Extensions/OMAP5432_uEVM
the execution stops at this point
**********************************************************************************************
U-Boot SPL 2013.10-rc2 (Mar 08 2016 - 14:23:51)
OMAP5432 ES2.0
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2013.10-rc2 (Mar 08 2016 - 14:23:51)
CPU : OMAP5432 ES2.0
Board: OMAP5432 uEVM
I2C: ready
DRAM: 2 GiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
Using default environment
Net: No ethernet found.
Hit any key to stop autoboot: 0
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading uEnv.txt
** Unable to read file uEnv.txt **
** File not found /boot/zImage **
U-Boot# setenv dtb_addr_r 0x825f0000
U-Boot# setenv xen_addr_r 0x90000000
U-Boot# setenv kernel_addr_r 0xa0000000
U-Boot# setenv xen_bootargs 'sync_console console=dtuart dtuart=serial2'
U-Boot# setenv dom0_bootargs 'console=hvc0,115200n8 earlyprintk=xen debug
ignore_loglevel root=/dev/mmcblk0p2 rw rootwait fixrtc'
U-Boot# fatload mmc 0:1 $dtb_addr_r omap5-uevm.dtb
reading omap5-uevm.dtb
44836 bytes read in 7 ms (6.1 MiB/s)
U-Boot# fatload mmc 0:1 $xen_addr_r xen-uImage
reading xen-uImage
787372 bytes read in 43 ms (17.5 MiB/s)
U-Boot# fatload mmc 0:1 $kernel_addr_r zImage
reading zImage
4284248 bytes read in 213 ms (19.2 MiB/s)
U-Boot# fdt addr $dtb_addr_r
U-Boot# fdt resize
U-Boot# fdt set /chosen xen,xen-bootargs \"$xen_bootargs\"
U-Boot# fdt resize
U-Boot# fdt set /chosen xen,dom0-bootargs \"$dom0_bootargs\"
U-Boot# fdt resize
U-Boot# fdt mknode /chosen modules
U-Boot# fdt set /chosen/modules '#address-cells' <1>
U-Boot# fdt set /chosen/modules '#size-cells' <1>
U-Boot# fdt mknode /chosen/modules module@0
U-Boot# fdt set /chosen/modules/module@0 compatible xen,linux-zimage
xen,multiboot-module
U-Boot# fdt set /chosen/modules/module@0 reg <$kernel_addr_r 0xa00000>
U-Boot# bootm $xen_addr_r - $dtb_addr_r
## Booting kernel from Legacy Image at 90000000 ...
Image Name:
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 787308 Bytes = 768.9 KiB
Load Address: 80200000
Entry Point: 80200000
Verifying Checksum ... OK
## Flattened Device Tree blob at 825f0000
Booting using the fdt blob at 0x825f0000
Loading Kernel Image ... OK
reserving fdt memory region: addr=825f0000 size=c000
Using Device Tree in place at 825f0000, end 825fefff
Starting kernel ...
- UART enabled -
- CPU 00000000 booting -
- Xen starting in Hyp mode -
- Zero BSS -
- Setting up control registers -
- Turning on paging -
- Ready -
(XEN) Checking for initrd in /chosen
(XEN) RAM: 0000000080000000 - 00000000feffffff
(XEN)
(XEN) MODULE[0]: 00000000825f0000 - 00000000825fc000 Device Tree
(XEN) MODULE[1]: 00000000a0000000 - 00000000a0a00000 Kernel
(XEN) RESVD[0]: 00000000825f0000 - 00000000825fc000
(XEN)
(XEN) Command line: sync_console console=dtuart dtuart=serial2
(XEN) Placing Xen at 0x00000000fee00000-0x00000000ff000000
(XEN) Update BOOTMOD_XEN from 0000000080200000-0000000080305701 =>
00000000fee00000-00000000fef05701
(XEN) Xen heap: 00000000fa000000-00000000fe000000 (16384 pages)
(XEN) Dom heap: 503808 pages
(XEN) Domain heap initialised
(XEN) Platform: TI OMAP5
(XEN) Looking for dtuart at "serial2", options ""
Xen 4.7-unstable
(XEN) Xen version 4.7-unstable (root@) (arm-linux-gnueabihf-gcc (Linaro GCC
2014.11) 4.9.3 20141031 (prerelease)) debug=y Tue Mar 1 15:02:30 CET 2016
(XEN) Latest ChangeSet: Sun Feb 28 16:03:51 2016 -0500 git:42391c6
(XEN) Console output is synchronous.
(XEN) Processor: 412fc0f2: "ARM Limited", variant: 0x2, part 0xc0f, rev 0x2
(XEN) 32-bit Execution:
(XEN) Processor Features: 00001131:00011011
(XEN) Instruction Sets: AArch32 A32 Thumb Thumb-2 ThumbEE Jazelle
(XEN) Extensions: GenericTimer Security
(XEN) Debug Features: 02010555
(XEN) Auxiliary Features: 00000000
(XEN) Memory Model Features: 10201105 20000000 01240000 02102211
(XEN) ISA Features: 02101110 13112111 21232041 11112131 10011142 00000000
(XEN) Set AuxCoreBoot1 to 00000000fee0004c (0020004c)
(XEN) Set AuxCoreBoot0 to 0x20
(XEN) Generic Timer IRQ: phys=30 hyp=26 virt=27 Freq: 6144 KHz
(XEN) GICv2: WARNING: The GICC size is too small: 0x1000 expected 0x2000
(XEN) GICv2 initialization:
(XEN) gic_dist_addr=0000000048211000
(XEN) gic_cpu_addr=0000000048212000
(XEN) gic_hyp_addr=0000000048214000
(XEN) gic_vcpu_addr=0000000048216000
(XEN) gic_maintenance_irq=25
(XEN) GICv2: 192 lines, 2 cpus, secure (IID 0000043b).
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Allocated console ring of 16 KiB.
(XEN) VFP implementer 0x41 architecture 4 part 0x30 variant 0xf rev 0x0
(XEN) Bringing up CPU1
- CPU 00000001 booting -
- Xen starting in Hyp mode -
- Setting up control registers -
- Turning on paging -
- Ready -
(XEN) CPU 1 booted.
(XEN) Brought up 2 CPUs
(XEN) P2M: 40-bit IPA
(XEN) P2M: 3 levels with order-1 root, VTCR 0x80003558
(XEN) I/O virtualisation disabled
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Loading kernel from boot module @ 00000000a0000000
(XEN) Allocating 1:1 mappings totalling 128MB for dom0:
(XEN) BANK[0] 0x000000a8000000-0x000000b0000000 (128MB)
(XEN) Grant table range: 0x000000fee00000-0x000000fee63000
(XEN) Loading zImage from 00000000a0000000 to
00000000afa00000-00000000afe15f58
(XEN) Allocating PPI 16 for event channel interrupt
(XEN) Loading dom0 DTB to 0x00000000af800000-0x00000000af80aece
(XEN) Scrubbing Free RAM on 1 nodes using 2 CPUs
(XEN) ........done.
(XEN) Initial low memory virq threshold set at 0x4000 pages.
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) **********************************************
(XEN) ******* WARNING: CONSOLE OUTPUT IS SYNCHRONOUS
(XEN) ******* This option is intended to aid debugging of Xen by ensuring
(XEN) ******* that all output is synchronously delivered on the serial line.
(XEN) ******* However it can introduce SIGNIFICANT latencies and affect
(XEN) ******* timekeeping. It is NOT recommended for production use!
(XEN) **********************************************
(XEN) 3... 2... 1...
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input
to Xen)
(XEN) Freed 280kB init memory.
**********************************************************************************************
nothing appears after (XEN) Freed 280kB init memory. .. i don't know
where is the problem
. i'll appreciate your help
thanks
[-- Attachment #1.2: Type: text/html, Size: 16177 bytes --]
[-- Attachment #2: Type: text/plain, Size: 126 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xen.org
http://lists.xen.org/xen-devel
next reply other threads:[~2016-03-10 20:04 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-03-10 20:04 Safa Hamza [this message]
2016-03-11 14:49 ` help Konrad Rzeszutek Wilk
[not found] ` <CAFwQ9hH6_7v57sw9c96GG=B9FdqFGn4WnDYO3RU5sLxEKQX7gg@mail.gmail.com>
[not found] ` <20160311152001.GJ5133@char.us.oracle.com>
2016-03-11 15:20 ` help Konrad Rzeszutek Wilk
[not found] ` <CAFwQ9hE_erNA4uCCpdKwWRdZXRF39YJ=mqo6dbOpeWkNdipyTA@mail.gmail.com>
2016-03-11 16:02 ` help Konrad Rzeszutek Wilk
2016-03-11 16:08 ` help Safa Hamza
2016-03-11 16:09 ` help Wei Liu
[not found] ` <CAFwQ9hFx_ctRJdPzuE03asqYwcdxAGPFii_Ns0WFk3dmrVSfBQ@mail.gmail.com>
2016-03-11 17:16 ` help Wei Liu
2016-03-15 17:56 ` help Julien Grall
2016-03-15 18:09 ` help Konrad Rzeszutek Wilk
2016-03-15 18:16 ` help Julien Grall
2016-03-15 18:21 ` help Konrad Rzeszutek Wilk
2016-03-15 18:22 ` help Julien Grall
2016-03-15 21:01 ` help Safa Hamza
2016-03-15 23:47 ` help Doug Goldstein
-- strict thread matches above, loose matches on Subject: below --
2020-11-28 14:32 help Rroach
2016-03-23 10:23 help Marwa Hamza
2015-07-23 15:05 Help Akash Talole
2015-07-24 7:46 ` Help Wei Liu
2015-07-03 8:45 Help Akash Talole
[not found] <557FA708.7020101@yahoo.fr>
2015-06-25 4:51 ` Help Luc Pierard de Maujouy
2015-06-25 8:51 ` Help Ian Campbell
2013-03-23 7:51 Help Arun Kv
2013-03-25 10:54 ` Help George Dunlap
2011-10-28 4:15 Help Pankaj Kumar Biswas
2011-10-28 8:47 ` Help Ian Campbell
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAFwQ9hHz9qDo10=apqsWWBuZitT5TGf0OB0LoTTOTXXXz8c-yQ@mail.gmail.com' \
--to=safahamza1@gmail.com \
--cc=xen-devel@lists.xenproject.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).