* SMP APIC warning
@ 2002-05-22 2:10 Pierre G. Martineau
0 siblings, 0 replies; only message in thread
From: Pierre G. Martineau @ 2002-05-22 2:10 UTC (permalink / raw)
To: linux-smp
[-- Attachment #1: Type: text/plain, Size: 259 bytes --]
Thought you might want to see this, in case you haven't yet. It's from a
Tyan S2603 dual P4 XEON.
Can you tell me why I can't build an SMP kernel on this machine whereas
the distribution version of RH7.3 SMP runs fine?
Regards,
Pierre Martineau
[-- Attachment #2: dmesg --]
[-- Type: application/octet-stream, Size: 18138 bytes --]
Linux version 2.4.18-4smp (bhcompile@stripples.devel.redhat.com) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-110)) #1 SMP Thu May 2 18:32:34 EDT 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ea000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fef0000 (usable)
BIOS-e820: 000000003fef0000 - 000000003feff000 (ACPI data)
BIOS-e820: 000000003feff000 - 000000003ff00000 (ACPI NVS)
BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
126MB HIGHMEM available.
found SMP MP-table at 000f6bf0
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
hm, page 0009f000 reserved twice.
hm, page 000a0000 reserved twice.
On node 0 totalpages: 261872
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32496 pages.
ACPI: Searched entire block, no RSDP was found.
ACPI: RSDP located at physical address c00f6b90
RSD PTR v0 [PTLTD ]
__va_range(0x3fefa08c, 0x68): idx=8 mapped at ffff6000
ACPI table found: RSDT v1 [PTLTD RSDT 1540.0]
__va_range(0x3fefeed4, 0x24): idx=8 mapped at ffff6000
__va_range(0x3fefeed4, 0x74): idx=8 mapped at ffff6000
ACPI table found: FACP v1 [ WOMBAT 1540.0]
__va_range(0x3fefef48, 0x24): idx=8 mapped at ffff6000
__va_range(0x3fefef48, 0x90): idx=8 mapped at ffff6000
ACPI table found: APIC v1 [PTLTD APIC 1540.0]
__va_range(0x3fefef48, 0x90): idx=8 mapped at ffff6000
LAPIC (acpi_id[0x0000] id[0x0] enabled[1])
CPU 0 (0x0000) enabledProcessor #0 Unknown CPU [15:2] APIC version 16
LAPIC (acpi_id[0x0001] id[0x6] enabled[1])
CPU 1 (0x0600) enabledProcessor #6 Unknown CPU [15:2] APIC version 16
LAPIC (acpi_id[0x0002] id[0x1] enabled[1])
CPU 2 (0x0100) enabledProcessor #1 Unknown CPU [15:2] APIC version 16
LAPIC (acpi_id[0x0003] id[0x7] enabled[1])
CPU 3 (0x0700) enabledProcessor #7 Unknown CPU [15:2] APIC version 16
IOAPIC (id[0x2] address[0xfec00000] global_irq_base[0x0])
IOAPIC (id[0x3] address[0xfec80000] global_irq_base[0x18])
INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x1] trigger[0x1])
INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
LAPIC_NMI (acpi_id[0x0000] polarity[0x1] trigger[0x1] lint[0x1])
LAPIC_NMI (acpi_id[0x0001] polarity[0x1] trigger[0x1] lint[0x1])
LAPIC_NMI (acpi_id[0x0002] polarity[0x1] trigger[0x1] lint[0x1])
LAPIC_NMI (acpi_id[0x0003] polarity[0x1] trigger[0x1] lint[0x1])
4 CPUs total
Local APIC address fee00000
__va_range(0x3fefefd8, 0x24): idx=8 mapped at ffff6000
__va_range(0x3fefefd8, 0x28): idx=8 mapped at ffff6000
ACPI table found: BOOT v1 [PTLTD $SBFTBL$ 1540.0]
Enabling the CPU's according to the ACPI table
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: Product ID: HP_WOMBAT APIC at: 0xFEE00000
I/O APIC #2 Version 32 at 0xFEC00000.
I/O APIC #3 Version 32 at 0xFEC80000.
Processors: 4
Kernel command line: ro root=/dev/sda6 hda=ide-scsi hdc=ide-scsi
ide_setup: hda=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 2194.675 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4377.80 BogoMIPS
Memory: 1029520k/1047488k available (1232k kernel code, 17576k reserved, 842k data, 304k init, 129984k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: Before vendor init, caps: 3febfbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 12K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After vendor init, caps: 3febfbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Before vendor init, caps: 3febfbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 12K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After vendor init, caps: 3febfbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU0: Intel(R) XEON(TM) CPU 2.20GHz stepping 04
per-CPU timeslice cutoff: 1463.14 usecs.
task migration cache decay timeout: 10 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4377.80 BogoMIPS
CPU: Before vendor init, caps: 3febfbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 12K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After vendor init, caps: 3febfbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU1: Intel(R) XEON(TM) CPU 2.20GHz stepping 04
Booting processor 2/6 eip 2000
Initializing CPU#2
masked ExtINT on CPU#2
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4377.80 BogoMIPS
CPU: Before vendor init, caps: 3febfbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 12K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU: After vendor init, caps: 3febfbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#2.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU2: Intel(R) XEON(TM) CPU 2.20GHz stepping 04
Booting processor 3/7 eip 2000
Initializing CPU#3
masked ExtINT on CPU#3
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4377.80 BogoMIPS
CPU: Before vendor init, caps: 3febfbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 12K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU: After vendor init, caps: 3febfbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#3.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU3: Intel(R) XEON(TM) CPU 2.20GHz stepping 04
Total of 4 processors activated (17511.21 BogoMIPS).
cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
cpu_sibling_map[2] = 3
cpu_sibling_map[3] = 2
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
Setting 3 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 3 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-10, 2-11, 2-12, 2-20, 2-22, 3-0, 3-1, 3-2, 3-3, 3-4, 3-5, 3-6, 3-7, 3-8, 3-9, 3-10, 3-11, 3-12, 3-13, 3-14, 3-15, 3-16, 3-17, 3-18, 3-19, 3-20, 3-21, 3-22, 3-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 24.
number of IO-APIC #2 registers: 24.
number of IO-APIC #3 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02008000
....... : physical APIC id: 02
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 00F 0F 0 0 0 0 0 1 1 39
02 00F 0F 0 0 0 0 0 1 1 31
03 00F 0F 0 0 0 0 0 1 1 41
04 00F 0F 0 0 0 0 0 1 1 49
05 00F 0F 0 0 0 0 0 1 1 51
06 00F 0F 0 0 0 0 0 1 1 59
07 00F 0F 0 0 0 0 0 1 1 61
08 00F 0F 0 0 0 0 0 1 1 69
09 00F 0F 0 0 0 0 0 1 1 71
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 00F 0F 0 0 0 0 0 1 1 79
0e 00F 0F 0 0 0 0 0 1 1 81
0f 00F 0F 0 0 0 0 0 1 1 89
10 00F 0F 1 1 0 1 0 1 1 91
11 00F 0F 1 1 0 1 0 1 1 99
12 00F 0F 1 1 0 1 0 1 1 A1
13 00F 0F 1 1 0 1 0 1 1 A9
14 000 00 1 0 0 0 0 0 0 00
15 00F 0F 1 1 0 1 0 1 1 B1
16 000 00 1 0 0 0 0 0 0 00
17 00F 0F 1 1 0 1 0 1 1 B9
IO APIC #3......
.... register #00: 03000000
....... : physical APIC id: 03
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 03000000
....... : arbitration: 03
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 1 0 0 0 0 0 0 00
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ21 -> 0:21
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2194.5197 MHz.
..... host bus clock speed is 99.7507 MHz.
cpu: 0, clocks: 997507, slice: 199501
CPU0<T0:997504,T1:798000,D:3,S:199501,C:997507>
cpu: 1, clocks: 997507, slice: 199501
cpu: 3, clocks: 997507, slice: 199501
cpu: 2, clocks: 997507, slice: 199501
CPU1<T0:997504,T1:598496,D:6,S:199501,C:997507>
CPU2<T0:997504,T1:398992,D:9,S:199501,C:997507>
CPU3<T0:997504,T1:199488,D:12,S:199501,C:997507>
checking TSC synchronization across CPUs: passed.
PCI: PCI BIOS revision 2.10 entry at 0xfd8fb, last bus=4
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
Unknown bridge resource 2: assuming transparent
Unknown bridge resource 2: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/2440] at 00:1f.0
PCI->APIC IRQ transform: (B0,I31,P3) -> 19
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI->APIC IRQ transform: (B3,I8,P0) -> 23
PCI->APIC IRQ transform: (B3,I8,P1) -> 19
PCI->APIC IRQ transform: (B4,I6,P0) -> 18
PCI->APIC IRQ transform: (B4,I6,P1) -> 19
PCI->APIC IRQ transform: (B4,I9,P0) -> 19
PCI->APIC IRQ transform: (B4,I9,P0) -> 19
PCI->APIC IRQ transform: (B4,I13,P0) -> 21
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
apm: disabled - APM is not SMP safe.
Starting kswapd
allocated 64 pages and 64 bhs reserved for the highmem bounces
VFS: Diskquotas version dquot_6.5.0 initialized
Detected PS/2 Mouse Port.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
ttyS04 at port 0x3080 (irq = 19) is a 16C950/954
ttyS05 at port 0x3088 (irq = 19) is a 16C950/954
ttyS06 at port 0x3090 (irq = 19) is a 16C950/954
ttyS07 at port 0x3098 (irq = 19) is a 16C950/954
Real Time Clock Driver v1.10e
block: 1024 slots per queue, batch=256
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev f9
PIIX4: chipset revision 4
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x10a0-0x10a7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x10a8-0x10af, BIOS settings: hdc:DMA, hdd:pio
hda: PLEXTOR CD-R PX-W4012A, ATAPI CD/DVD-ROM drive
hdc: PIONEER DVD-RW DVR-104, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide-floppy driver 0.99.newide
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
pci_hotplug: PCI Hot Plug PCI Core version: 0.4
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 160k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
sym53c8xx: at PCI bus 3, device 8, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1010-66 detected with Symbios NVRAM
sym53c8xx: at PCI bus 3, device 8, function 1
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1010-66 detected with Symbios NVRAM
sym53c1010-66-0: rev 0x1 on pci bus 3 device 8 function 0 irq 23
sym53c1010-66-0: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-66-0: on-chip RAM at 0xe1000000
sym53c1010-66-0: restart (scsi reset).
sym53c1010-66-0: handling phase mismatch from SCRIPTS.
sym53c1010-66-0: Downloading SCSI SCRIPTS.
sym53c1010-66-1: rev 0x1 on pci bus 3 device 8 function 1 irq 19
sym53c1010-66-1: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-66-1: on-chip RAM at 0xe1002000
sym53c1010-66-1: restart (scsi reset).
sym53c1010-66-1: handling phase mismatch from SCRIPTS.
sym53c1010-66-1: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx-1.7.3c-20010512
scsi1 : sym53c8xx-1.7.3c-20010512
blk: queue f7fd4e18, I/O limit 4095Mb (mask 0xffffffff)
Vendor: SEAGATE Model: ST336752LW Rev: 0004
Type: Direct-Access ANSI SCSI revision: 03
blk: queue f7fd4c18, I/O limit 4095Mb (mask 0xffffffff)
sym53c1010-66-0-<0,0>: tagged command queue depth set to 8
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
sym53c1010-66-0-<0,*>: FAST-80 WIDE SCSI 160.0 MB/s (12.5 ns, offset 62)
SCSI device sda: 71687369 512-byte hdwr sectors (36704 MB)
Partition check:
sda: sda1 sda2 sda3 < sda5 sda6 sda7 > sda4
Freeing unused kernel memory: 304k freed
Adding Swap: 1028120k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 18:40:49 May 2 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1f.2 to 64
usb-uhci.c: USB UHCI at I/O 0x1080, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x46d/0xc00c) is not claimed by any active driver.
usb.c: registered new driver hiddev
usb.c: registered new driver hid
input0: USB HID v1.10 Mouse [Logitech USB Mouse] on usb1:2.0
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
scsi2 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: PLEXTOR Model: CD-R PX-W4012A Rev: 1.01
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PIONEER Model: DVD-RW DVR-104 Rev: 1.20
Type: CD-ROM ANSI SCSI revision: 02
hda: DMA disabled
hdc: DMA disabled
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2002-05-22 2:10 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2002-05-22 2:10 SMP APIC warning Pierre G. Martineau
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.