From: Brendan Pike <spike@superweb.ca>
To: linux-kernel@vger.kernel.org
Subject: Re: IDE Harddrive Performance
Date: Thu, 20 Dec 2001 09:12:28 -0400 [thread overview]
Message-ID: <01122009122800.27161@spikes> (raw)
Well i really cant explain this,
[root@spikes spike]# /sbin/hdparm -t /dev/hda
/dev/hda:
Timing buffered disk reads: 64 MB in 6.65 seconds = 9.62 MB/sec
[root@spikes spike]# cat /proc/ide/via
----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.29
South Bridge: VIA vt82c586b
Revision: ISA 0x47 IDE 0x6
Highest DMA rate: UDMA33
BM-DMA base: 0xe000
PCI clock: 33MHz
Master Read Cycle IRDY: 1ws
Master Write Cycle IRDY: 1ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: yes yes
Post Write Buffer: yes no
Enabled: yes yes
Simplex only: no no
Cable Type: 40w 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: UDMA PIO UDMA PIO
Address Setup: 30ns 120ns 30ns 120ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 30ns 30ns
Data Active: 90ns 330ns 90ns 330ns
Data Recovery: 30ns 270ns 30ns 270ns
Cycle Time: 60ns 600ns 60ns 600ns
Transfer Rate: 33.0MB/s 3.3MB/s 33.0MB/s 3.3MB/s
[root@spikes spike]# /sbin/hdparm -i /dev/hda
/dev/hda:
Model=FUJITSU MPG3409AT E, FwRev=82B9, SerialNo=VH06T1408HST
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=80063424
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
[root@spikes spike]# /sbin/hdparm /dev/hda
/dev/hda:
multcount = 16 (on)
I/O support = 3 (32-bit w/sync)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 4983/255/63, sectors = 80063424, start = 0
Kernel 2.4.16 without patches.
next reply other threads:[~2001-12-20 13:12 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-12-20 13:12 Brendan Pike [this message]
-- strict thread matches above, loose matches on Subject: below --
2001-12-23 17:55 IDE Harddrive Performance Wayne Whitney
2001-12-23 18:37 ` Mark Hahn
2001-12-22 18:20 Jim Radford
2001-12-22 21:36 ` Craig Knox
2001-12-23 8:11 ` Adam Keys
[not found] <Pine.LNX.4.33.0112201307120.9437-100000@coffee.psychology.mcmaster.ca>
2001-12-20 19:33 ` Brendan Pike
2001-12-20 19:25 Brendan Pike
2001-12-20 17:10 Brendan Pike
2001-12-20 17:22 ` Ryan Cumming
2001-12-20 17:41 ` Sebastian Dröge
2001-12-19 15:32 Thomas Deselaers
2001-12-19 15:44 ` Brendan Pike
2001-12-19 15:55 ` Lee Packham
2001-12-19 16:01 ` Jan Niehusmann
2001-12-19 16:18 ` Brendan Pike
2001-12-19 16:28 ` Oleg Artamonov
2001-12-19 16:44 ` Vojtech Pavlik
2001-12-19 16:59 ` Dmitry Pogosyan
[not found] ` <Pine.LNX.4.33.0112191101230.4575-100000@coffee.psychology.mcmaster.ca>
2001-12-19 16:37 ` Thomas Deselaers
2001-12-19 17:34 ` Mike Dresser
2001-12-19 15:55 ` Oleg Artamonov
2001-12-19 16:05 ` Thomas Deselaers
2001-12-19 16:15 ` Oleg Artamonov
2001-12-19 16:32 ` Thomas Deselaers
2001-12-19 16:38 ` Holger Lubitz
2001-12-22 8:21 ` Adam Keys
2001-12-22 8:56 ` Alan Cox
2001-12-22 10:10 ` Adam Keys
[not found] ` <01122215090500.01870@manta>
2001-12-22 13:23 ` Thomas Deselaers
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=01122009122800.27161@spikes \
--to=spike@superweb.ca \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.