From: Sangbeom Kim <sbkim73@samsung.com>
To: "'Mark Brown'" <broonie@opensource.wolfsonmicro.com>,
"'Liam Girdwood'" <lrg@ti.com>
Cc: linux-kernel@vger.kernel.org, sameo@linux.intel.com, sbkim01@gmail.com
Subject: [PATCH 5/5] regulator: Support AP watchdog reset operation for s5m8767a
Date: Wed, 13 Jun 2012 17:28:47 +0900 [thread overview]
Message-ID: <042301cd493e$8d95d7e0$a8c187a0$@com> (raw)
After AP watchdog reset, S5M8767A should be reset too.
If AP is set on lowest voltage, AP can't execute boot sequence.
This patch support watchdog reset of s5m8767.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
---
drivers/regulator/s5m8767.c | 137 +++++++++++++++++++++++-----------
include/linux/mfd/s5m87xx/s5m-core.h | 5 +
2 files changed, 98 insertions(+), 44 deletions(-)
diff --git a/drivers/regulator/s5m8767.c b/drivers/regulator/s5m8767.c
index 770e4df..533bde6 100644
--- a/drivers/regulator/s5m8767.c
+++ b/drivers/regulator/s5m8767.c
@@ -41,6 +41,7 @@ struct s5m8767_info {
u8 buck3_vol[8];
u8 buck4_vol[8];
int buck_gpios[3];
+ int buck_ds[3];
int buck_gpioindex;
};
@@ -283,17 +284,17 @@ static int s5m8767_get_voltage_register(struct regulator_dev *rdev, int *_reg)
reg = S5M8767_REG_BUCK1CTRL2;
break;
case S5M8767_BUCK2:
- reg = S5M8767_REG_BUCK2DVS1;
+ reg = S5M8767_REG_BUCK2DVS2;
if (s5m8767->buck2_gpiodvs)
reg += s5m8767->buck_gpioindex;
break;
case S5M8767_BUCK3:
- reg = S5M8767_REG_BUCK3DVS1;
+ reg = S5M8767_REG_BUCK3DVS2;
if (s5m8767->buck3_gpiodvs)
reg += s5m8767->buck_gpioindex;
break;
case S5M8767_BUCK4:
- reg = S5M8767_REG_BUCK4DVS1;
+ reg = S5M8767_REG_BUCK4DVS2;
if (s5m8767->buck4_gpiodvs)
reg += s5m8767->buck_gpioindex;
break;
@@ -512,7 +513,7 @@ static __devinit int s5m8767_pmic_probe(struct platform_device *pdev)
struct regulator_config config = { };
struct regulator_dev **rdev;
struct s5m8767_info *s5m8767;
- int i, ret, size;
+ int i, ret, size, buck_init;
if (!pdata) {
dev_err(pdev->dev.parent, "Platform data not supplied\n");
@@ -563,12 +564,37 @@ static __devinit int s5m8767_pmic_probe(struct platform_device *pdev)
s5m8767->buck_gpios[0] = pdata->buck_gpios[0];
s5m8767->buck_gpios[1] = pdata->buck_gpios[1];
s5m8767->buck_gpios[2] = pdata->buck_gpios[2];
+ s5m8767->buck_ds[0] = pdata->buck_ds[0];
+ s5m8767->buck_ds[1] = pdata->buck_ds[1];
+ s5m8767->buck_ds[2] = pdata->buck_ds[2];
+
s5m8767->ramp_delay = pdata->buck_ramp_delay;
s5m8767->buck2_ramp = pdata->buck2_ramp_enable;
s5m8767->buck3_ramp = pdata->buck3_ramp_enable;
s5m8767->buck4_ramp = pdata->buck4_ramp_enable;
s5m8767->opmode = pdata->opmode;
+ buck_init = s5m8767_convert_voltage_to_sel(&buck_voltage_val2,
+ pdata->buck2_init,
+ pdata->buck2_init +
+ buck_voltage_val2.step);
+
+ s5m_reg_write(s5m8767->iodev, S5M8767_REG_BUCK2DVS2, buck_init);
+
+ buck_init = s5m8767_convert_voltage_to_sel(&buck_voltage_val2,
+ pdata->buck3_init,
+ pdata->buck3_init +
+ buck_voltage_val2.step);
+
+ s5m_reg_write(s5m8767->iodev, S5M8767_REG_BUCK3DVS2, buck_init);
+
+ buck_init = s5m8767_convert_voltage_to_sel(&buck_voltage_val2,
+ pdata->buck4_init,
+ pdata->buck4_init +
+ buck_voltage_val2.step);
+
+ s5m_reg_write(s5m8767->iodev, S5M8767_REG_BUCK4DVS2, buck_init);
+
for (i = 0; i < 8; i++) {
if (s5m8767->buck2_gpiodvs) {
s5m8767->buck2_vol[i] =
@@ -598,48 +624,71 @@ static __devinit int s5m8767_pmic_probe(struct platform_device *pdev)
}
}
- if (pdata->buck2_gpiodvs || pdata->buck3_gpiodvs ||
- pdata->buck4_gpiodvs) {
- if (gpio_is_valid(pdata->buck_gpios[0]) &&
- gpio_is_valid(pdata->buck_gpios[1]) &&
- gpio_is_valid(pdata->buck_gpios[2])) {
- ret = gpio_request(pdata->buck_gpios[0],
- "S5M8767 SET1");
- if (ret == -EBUSY)
- dev_warn(&pdev->dev, "Duplicated gpio request for SET1\n");
-
- ret = gpio_request(pdata->buck_gpios[1],
- "S5M8767 SET2");
- if (ret == -EBUSY)
- dev_warn(&pdev->dev, "Duplicated gpio request for SET2\n");
-
- ret = gpio_request(pdata->buck_gpios[2],
- "S5M8767 SET3");
- if (ret == -EBUSY)
- dev_warn(&pdev->dev, "Duplicated gpio request for SET3\n");
- /* SET1 GPIO */
- gpio_direction_output(pdata->buck_gpios[0],
- (s5m8767->buck_gpioindex >> 2) & 0x1);
- /* SET2 GPIO */
- gpio_direction_output(pdata->buck_gpios[1],
- (s5m8767->buck_gpioindex >> 1) & 0x1);
- /* SET3 GPIO */
- gpio_direction_output(pdata->buck_gpios[2],
- (s5m8767->buck_gpioindex >> 0) & 0x1);
- ret = 0;
- } else {
- dev_err(&pdev->dev, "GPIO NOT VALID\n");
- ret = -EINVAL;
- return ret;
- }
+ if (gpio_is_valid(pdata->buck_gpios[0]) &&
+ gpio_is_valid(pdata->buck_gpios[1]) &&
+ gpio_is_valid(pdata->buck_gpios[2])) {
+ ret = gpio_request(pdata->buck_gpios[0], "S5M8767 SET1");
+ if (ret == -EBUSY)
+ dev_warn(&pdev->dev, "Duplicated gpio request"
+ " for SET1\n");
+
+ ret = gpio_request(pdata->buck_gpios[1], "S5M8767 SET2");
+ if (ret == -EBUSY)
+ dev_warn(&pdev->dev, "Duplicated gpio request"
+ " for SET2\n");
+
+ ret = gpio_request(pdata->buck_gpios[2], "S5M8767 SET3");
+ if (ret == -EBUSY)
+ dev_warn(&pdev->dev, "Duplicated gpio request"
+ " for SET3\n");
+ /* SET1 GPIO */
+ gpio_direction_output(pdata->buck_gpios[0],
+ (s5m8767->buck_gpioindex >> 2) & 0x1);
+ /* SET2 GPIO */
+ gpio_direction_output(pdata->buck_gpios[1],
+ (s5m8767->buck_gpioindex >> 1) & 0x1);
+ /* SET3 GPIO */
+ gpio_direction_output(pdata->buck_gpios[2],
+ (s5m8767->buck_gpioindex >> 0) & 0x1);
+ ret = 0;
+
+ } else {
+ dev_err(&pdev->dev, "GPIO NOT VALID\n");
+ ret = -EINVAL;
+ return ret;
}
- s5m_reg_update(s5m8767->iodev, S5M8767_REG_BUCK2CTRL,
- (pdata->buck2_gpiodvs) ? (1 << 1) : (0 << 1), 1 << 1);
- s5m_reg_update(s5m8767->iodev, S5M8767_REG_BUCK3CTRL,
- (pdata->buck3_gpiodvs) ? (1 << 1) : (0 << 1), 1 << 1);
- s5m_reg_update(s5m8767->iodev, S5M8767_REG_BUCK4CTRL,
- (pdata->buck4_gpiodvs) ? (1 << 1) : (0 << 1), 1 << 1);
+ ret = gpio_request(pdata->buck_ds[0], "S5M8767 DS2");
+ if (ret == -EBUSY)
+ dev_warn(&pdev->dev, "Duplicated gpio request for DS2\n");
+
+ ret = gpio_request(pdata->buck_ds[1], "S5M8767 DS3");
+ if (ret == -EBUSY)
+ dev_warn(&pdev->dev, "Duplicated gpio request for DS3\n");
+
+ ret = gpio_request(pdata->buck_ds[2], "S5M8767 DS4");
+ if (ret == -EBUSY)
+ dev_warn(&pdev->dev, "Duplicated gpio request for DS4\n");
+
+ /* DS2 GPIO */
+ gpio_direction_output(pdata->buck_ds[0], 0x0);
+ /* DS3 GPIO */
+ gpio_direction_output(pdata->buck_ds[1], 0x0);
+ /* DS4 GPIO */
+ gpio_direction_output(pdata->buck_ds[2], 0x0);
+
+ if (pdata->buck2_gpiodvs || pdata->buck3_gpiodvs ||
+ pdata->buck4_gpiodvs) {
+ s5m_reg_update(s5m8767->iodev, S5M8767_REG_BUCK2CTRL,
+ (pdata->buck2_gpiodvs) ? (1 << 1) : (0 << 1),
+ 1 << 1);
+ s5m_reg_update(s5m8767->iodev, S5M8767_REG_BUCK3CTRL,
+ (pdata->buck3_gpiodvs) ? (1 << 1) : (0 << 1),
+ 1 << 1);
+ s5m_reg_update(s5m8767->iodev, S5M8767_REG_BUCK4CTRL,
+ (pdata->buck4_gpiodvs) ? (1 << 1) : (0 << 1),
+ 1 << 1);
+ }
/* Initialize GPIO DVS registers */
for (i = 0; i < 8; i++) {
diff --git a/include/linux/mfd/s5m87xx/s5m-core.h b/include/linux/mfd/s5m87xx/s5m-core.h
index 21603b4..0b2e0ed 100644
--- a/include/linux/mfd/s5m87xx/s5m-core.h
+++ b/include/linux/mfd/s5m87xx/s5m-core.h
@@ -347,6 +347,7 @@ struct s5m_platform_data {
bool buck_voltage_lock;
int buck_gpios[3];
+ int buck_ds[3];
int buck2_voltage[8];
bool buck2_gpiodvs;
int buck3_voltage[8];
@@ -369,6 +370,10 @@ struct s5m_platform_data {
bool buck2_ramp_enable;
bool buck3_ramp_enable;
bool buck4_ramp_enable;
+
+ int buck2_init;
+ int buck3_init;
+ int buck4_init;
};
#endif /* __LINUX_MFD_S5M_CORE_H */
--
1.7.1
next reply other threads:[~2012-06-13 8:28 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-06-13 8:28 Sangbeom Kim [this message]
2012-06-13 17:46 ` [PATCH 5/5] regulator: Support AP watchdog reset operation for s5m8767a Mark Brown
2012-06-14 0:01 ` Sangbeom Kim
2012-06-17 18:53 ` Mark Brown
2012-06-17 23:56 ` Sangbeom Kim
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='042301cd493e$8d95d7e0$a8c187a0$@com' \
--to=sbkim73@samsung.com \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=linux-kernel@vger.kernel.org \
--cc=lrg@ti.com \
--cc=sameo@linux.intel.com \
--cc=sbkim01@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.