[PATCH] arm64: dts: exynos: Added the ethernet pin configuration

[PATCH] arm64: dts: exynos: Added the ethernet pin configuration

[Yashwant Varur]

This patch adds the ethernet pin configuration.

Signed-off-by: Yashwant Varur <yashwant.v@samsung.com>
Signed-off-by: Changsub Lee <cs0617.lee@samsung.com>
---
 .../dts/exynos/exynosautov920-pinctrl.dtsi    | 41 +++++++++++++++++++
 1 file changed, 41 insertions(+)

diff --git a/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
index 663e8265cbf5..778584d339d5 100644
--- a/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
@@ -166,6 +166,24 @@ gph6: gph6-gpio-bank {
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
+
+	eth0_pps_out: eth0_pps_out {
+		samsung,pins = "gph3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	eth0_rgmii: eth0_rgmii {
+		samsung,pins = "gph3-1", "gph3-2", "gph3-3", "gph3-4",
+				"gph3-5", "gph3-6", "gph3-7", "gph4-0",
+				"gph4-1", "gph4-2", "gph4-3", "gph4-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+	};
+
+	eth0_mdc_mdio: eth0_mdc_mdio {
+		samsung,pins = "gph4-5", "gph4-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+	};
 };
 
 &pinctrl_hsi2ufs {
@@ -750,6 +768,29 @@ i3c3_bus: i3c3-bus-pins {
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
+
+	eth_extpll_avb: eth_extpll_avb {
+		samsung,pins = "gpg3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	eth0_pps_out0: eth0_pps_out0 {
+		samsung,pins = "gpg0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+	};
+
+	eth0_pps_out1: eth0_pps_out1 {
+		samsung,pins = "gpg0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+	};
+
+	eth_phy_reset: eth_phy_reset {
+		samsung,pins = "gpg3-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+	};
+
 };
 
 &pinctrl_peric1 {
-- 
2.34.1

RE: [PATCH] arm64: dts: exynos: Added the ethernet pin configuration

[Alim Akhtar]

Hi Yashwant,

> -----Original Message-----
> From: Yashwant Varur <yashwant.v@samsung.com>
> Sent: Wednesday, April 23, 2025 11:31 AM
> To: robh@kernel.org; krzk+dt@kernel.org; conor+dt@kernel.org;
> alim.akhtar@samsung.com; devicetree@vger.kernel.org; linux-arm-
> kernel@lists.infradead.org; linux-samsung-soc@vger.kernel.org; linux-
> kernel@vger.kernel.org
> Cc: cs0617.lee@samsung.com; g.naidu@samsung.com;
> niyas.ahmed@samsung.com; yashwant.v@samsung.com
> Subject: [PATCH] arm64: dts: exynos: Added the ethernet pin configuration
> 
> This patch adds the ethernet pin configuration.
> 
Please follow https://www.kernel.org/doc/html/latest/process/submitting-patches.html#describe-your-changes
to describe our changes.

> Signed-off-by: Yashwant Varur <yashwant.v@samsung.com>
> Signed-off-by: Changsub Lee <cs0617.lee@samsung.com>
> ---
>  .../dts/exynos/exynosautov920-pinctrl.dtsi    | 41 +++++++++++++++++++
>  1 file changed, 41 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
> b/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
> index 663e8265cbf5..778584d339d5 100644
> --- a/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
> +++ b/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
> @@ -166,6 +166,24 @@ gph6: gph6-gpio-bank {
>  		interrupt-controller;
>  		#interrupt-cells = <2>;
>  	};
> +
> +	eth0_pps_out: eth0_pps_out {
> +		samsung,pins = "gph3-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +
> +	eth0_rgmii: eth0_rgmii {
> +		samsung,pins = "gph3-1", "gph3-2", "gph3-3", "gph3-4",
> +				"gph3-5", "gph3-6", "gph3-7", "gph4-0",
> +				"gph4-1", "gph4-2", "gph4-3", "gph4-4";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +	};
> +
> +	eth0_mdc_mdio: eth0_mdc_mdio {
> +		samsung,pins = "gph4-5", "gph4-6";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
No need to set drive strength and pull-{up/down}??

Re: [PATCH] arm64: dts: exynos: Added the ethernet pin configuration

[Rob Herring (Arm)]

On Wed, 23 Apr 2025 11:30:34 +0530, Yashwant Varur wrote:
> This patch adds the ethernet pin configuration.
> 
> Signed-off-by: Yashwant Varur <yashwant.v@samsung.com>
> Signed-off-by: Changsub Lee <cs0617.lee@samsung.com>
> ---
>  .../dts/exynos/exynosautov920-pinctrl.dtsi    | 41 +++++++++++++++++++
>  1 file changed, 41 insertions(+)
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


This patch series was applied (using b4) to base:
 Base: attempting to guess base-commit...
 Base: tags/next-20250423 (exact match)

If this is not the correct base, please add 'base-commit' tag
(or use b4 which does this automatically)

New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/exynos/' for 20250423060034.973-1-yashwant.v@samsung.com:

arch/arm64/boot/dts/exynos/exynosautov920-sadk.dtb: pinctrl@10830000 (samsung,exynosautov920-pinctrl): 'eth0_pps_out0', 'eth0_pps_out1', 'eth_extpll_avb', 'eth_phy_reset' do not match any of the regexes: '^(initial|sleep)-state$', '^[a-z0-9-]+-pins$', '^[a-z]+[0-9]*-gpio-bank$', '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/pinctrl/samsung,pinctrl.yaml#
arch/arm64/boot/dts/exynos/exynosautov920-sadk.dtb: pinctrl@16c10000 (samsung,exynosautov920-pinctrl): 'eth0_mdc_mdio', 'eth0_pps_out', 'eth0_rgmii' do not match any of the regexes: '^(initial|sleep)-state$', '^[a-z0-9-]+-pins$', '^[a-z]+[0-9]*-gpio-bank$', '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/pinctrl/samsung,pinctrl.yaml#

Re: [PATCH] arm64: dts: exynos: Added the ethernet pin configuration

[Krzysztof Kozlowski]

On 23/04/2025 08:00, Yashwant Varur wrote:
> This patch adds the ethernet pin configuration.


> 
> Signed-off-by: Yashwant Varur <yashwant.v@samsung.com>
> Signed-off-by: Changsub Lee <cs0617.lee@samsung.com>

Incorrect chain or confusing. Who was the author? What is the meaning of
the last SoB?


> ---
>  .../dts/exynos/exynosautov920-pinctrl.dtsi    | 41 +++++++++++++++++++
>  1 file changed, 41 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
> index 663e8265cbf5..778584d339d5 100644
> --- a/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
> +++ b/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
> @@ -166,6 +166,24 @@ gph6: gph6-gpio-bank {
>  		interrupt-controller;
>  		#interrupt-cells = <2>;
>  	};
> +
> +	eth0_pps_out: eth0_pps_out {

Please follow DTS coding style carefully. This applies to all commits
you try to send from your downstream/vendor code.

What is more important, I don't really understand why you are doing this
- there is no user of these entries - and commit msg does not help here.


Best regards,
Krzysztof

RE: [PATCH] arm64: dts: exynos: Added the ethernet pin configuration

[Yashwant Varur]

-----Original Message-----
From: Krzysztof Kozlowski <krzk@kernel.org> 
Sent: Wednesday, April 23, 2025 8:41 PM
To: Yashwant Varur <yashwant.v@samsung.com>; robh@kernel.org; krzk+dt@kernel.org; conor+dt@kernel.org; alim.akhtar@samsung.com; devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux-samsung-soc@vger.kernel.org; linux-kernel@vger.kernel.org
Cc: cs0617.lee@samsung.com; g.naidu@samsung.com; niyas.ahmed@samsung.com
Subject: Re: [PATCH] arm64: dts: exynos: Added the ethernet pin configuration

On 23/04/2025 08:00, Yashwant Varur wrote:
> This patch adds the ethernet pin configuration.


> 
> Signed-off-by: Yashwant Varur <yashwant.v@samsung.com>
> Signed-off-by: Changsub Lee <cs0617.lee@samsung.com>

Incorrect chain or confusing. Who was the author? What is the meaning of the last SoB?
>
Sorry will correct the order.


> ---
>  .../dts/exynos/exynosautov920-pinctrl.dtsi    | 41 +++++++++++++++++++
>  1 file changed, 41 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi 
> b/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
> index 663e8265cbf5..778584d339d5 100644
> --- a/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
> +++ b/arch/arm64/boot/dts/exynos/exynosautov920-pinctrl.dtsi
> @@ -166,6 +166,24 @@ gph6: gph6-gpio-bank {
>  		interrupt-controller;
>  		#interrupt-cells = <2>;
>  	};
> +
> +	eth0_pps_out: eth0_pps_out {

Please follow DTS coding style carefully. This applies to all commits you try to send from your downstream/vendor code.
>
Sure, thanks

What is more important, I don't really understand why you are doing this
- there is no user of these entries - and commit msg does not help here.
>
Understood, in v2 will add the Ethernet node as well.



Best regards,
Krzysztof

Re: [PATCH] arm64: dts: exynos: Added the ethernet pin configuration

[Krzysztof Kozlowski]

On 29/04/2025 11:29, Yashwant Varur wrote:
> 
> Please follow DTS coding style carefully. This applies to all commits you try to send from your downstream/vendor code.


hm?

>>
> Sure, thanks
> 
> What is more important, I don't really understand why you are doing this
> - there is no user of these entries - and commit msg does not help here.
>>
> Understood, in v2 will add the Ethernet node as well.

I don't understand what is your reply here and what is quote. Use
standard email style, not some mySingle or Outlook output. I suggest
reading typical guidelines how to use email based workflows (kernel also
has one).


Best regards,
Krzysztof

RE: [PATCH] arm64: dts: exynos: Added the ethernet pin configuration

[Yashwant Varur]

Hi Krzysztof

> -----Original Message-----
> From: Krzysztof Kozlowski <krzk@kernel.org>
> Sent: Tuesday, April 29, 2025 6:37 PM
> To: Yashwant Varur <yashwant.v@samsung.com>; robh@kernel.org;
> krzk+dt@kernel.org; conor+dt@kernel.org; alim.akhtar@samsung.com;
> devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux-
> samsung-soc@vger.kernel.org; linux-kernel@vger.kernel.org
> Cc: cs0617.lee@samsung.com; g.naidu@samsung.com;
> niyas.ahmed@samsung.com
> Subject: Re: [PATCH] arm64: dts: exynos: Added the ethernet pin configuration
> 
> On 29/04/2025 11:29, Yashwant Varur wrote:
> >
> > Please follow DTS coding style carefully. This applies to all commits you try to
> send from your downstream/vendor code.
> 
> 
> hm?
> 
Got the issue, coding style says
Node and property names can use only the following characters:
Lowercase characters: [a-z]
Digits: [0-9]
Dash: -
I was using underscore for node name.
> >>
> > Sure, thanks
> >
> > What is more important, I don't really understand why you are doing
> > this
> > - there is no user of these entries - and commit msg does not help here.
> >>
> > Understood, in v2 will add the Ethernet node as well.
> 
> I don't understand what is your reply here and what is quote. Use standard email
> style, not some mySingle or Outlook output. I suggest reading typical guidelines
> how to use email based workflows (kernel also has one).
> 

Looks like mailer was not configured properly, hope this time it is fine.
I am working on upstreaming Ethernet driver for exynosauto (which has a variant of STMMAC controller)
What I wanted to reply previously was, will add pin control, along with Ethernet node(which will consume the pincontrol) and
I realize that first dt-binding should go for this IP.
My plan is to send Ethernet driver along with Ethernet dtsi node as well.

> 
> Best regards,
> Krzysztof

Re: [PATCH] arm64: dts: exynos: Added the ethernet pin configuration

[kernel test robot]

:::::: 
:::::: Manual check reason: "dtcheck: binding changes may go via different trees"
:::::: 

BCC: lkp@intel.com
CC: oe-kbuild-all@lists.linux.dev
In-Reply-To: <20250423060034.973-1-yashwant.v@samsung.com>
References: <20250423060034.973-1-yashwant.v@samsung.com>
TO: Yashwant Varur <yashwant.v@samsung.com>
TO: robh@kernel.org
TO: krzk+dt@kernel.org
TO: conor+dt@kernel.org
TO: alim.akhtar@samsung.com
TO: devicetree@vger.kernel.org
TO: linux-arm-kernel@lists.infradead.org
TO: linux-samsung-soc@vger.kernel.org
TO: linux-kernel@vger.kernel.org
CC: cs0617.lee@samsung.com
CC: g.naidu@samsung.com
CC: niyas.ahmed@samsung.com
CC: yashwant.v@samsung.com

Hi Yashwant,

kernel test robot noticed the following build warnings:

[auto build test WARNING on krzk/for-next]
[also build test WARNING on linus/master v6.15-rc4 next-20250502]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Yashwant-Varur/arm64-dts-exynos-Added-the-ethernet-pin-configuration/20250423-150049
base:   https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux.git for-next
patch link:    https://lore.kernel.org/r/20250423060034.973-1-yashwant.v%40samsung.com
patch subject: [PATCH] arm64: dts: exynos: Added the ethernet pin configuration
:::::: branch date: 10 days ago
:::::: commit date: 10 days ago
config: arm64-randconfig-053-20250429 (https://download.01.org/0day-ci/archive/20250503/202505030518.6NIdhVxK-lkp@intel.com/config)
compiler: aarch64-linux-gcc (GCC) 9.5.0
dtschema version: 2025.3.dev21+ge6ea659
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20250503/202505030518.6NIdhVxK-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/r/202505030518.6NIdhVxK-lkp@intel.com/

dtcheck warnings: (new ones prefixed by >>)
>> arch/arm64/boot/dts/exynos/exynosautov920-sadk.dtb: pinctrl@10830000 (samsung,exynosautov920-pinctrl): 'eth0_pps_out0', 'eth0_pps_out1', 'eth_extpll_avb', 'eth_phy_reset' do not match any of the regexes: '^(initial|sleep)-state$', '^[a-z0-9-]+-pins$', '^[a-z]+[0-9]*-gpio-bank$', 'pinctrl-[0-9]+'
   	from schema $id: http://devicetree.org/schemas/pinctrl/samsung,pinctrl.yaml#
>> arch/arm64/boot/dts/exynos/exynosautov920-sadk.dtb: pinctrl@16c10000 (samsung,exynosautov920-pinctrl): 'eth0_mdc_mdio', 'eth0_pps_out', 'eth0_rgmii' do not match any of the regexes: '^(initial|sleep)-state$', '^[a-z0-9-]+-pins$', '^[a-z]+[0-9]*-gpio-bank$', 'pinctrl-[0-9]+'
   	from schema $id: http://devicetree.org/schemas/pinctrl/samsung,pinctrl.yaml#

-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki