* New Script
@ 2003-01-09 12:38 mdew
2003-01-09 13:38 ` Arnt Karlsen
2003-01-09 15:06 ` Anders Fugmann
0 siblings, 2 replies; 3+ messages in thread
From: mdew @ 2003-01-09 12:38 UTC (permalink / raw)
To: netfilter
Ok, after taking a few samples from scripts in the mailing list, Ive
come up with this...hopefully my edonkey problem has been solved with
this script. I havent actually tested this yet, Probably tomorrow (its a
bit late)
current Router setup.
(Internet) 210.54.175.12->eth0---Router--->eth1 10.0.0.6 -=> 10.0.0.x
#!/bin/bash
IPTABLES="/sbin/iptables"
PAUL="10.0.0.9"
echo "1" > /proc/sys/net/ipv4/ip_forward
echo "Executing The Firwall..."
echo ""
echo -n "Loading Modules..."
/sbin/modprobe ip_conntrack_ftp
/sbin/modprobe ip_conntrack_irc
/sbin/modprobe ip_nat_irc
/sbin/modprobe ip_nat_ftp
/sbin/modprobe ipt_state
/sbin/modprobe ipt_limit
/sbin/modprobe ipt_LOG
echo -n "Done"
$IPTABLES -F INPUT
$IPTABLES -F OUTPUT
$IPTABLES -F FORWARD
$IPTABLES -P INPUT ACCEPT
$IPTABLES -P OUTPUT ACCEPT
echo "Allow unlimited traffic on the loopback interface"
$IPTABLES -A INPUT -i lo -j ACCEPT
$IPTABLES -A OUTPUT -o lo -j ACCEPT
echo "Refusing spoofed packets pretending to be from your IP address"
$IPTABLES -A INPUT -s 210.54.175.12 -j DROP
echo "Allow SSH"
# Is this correct?
$IPTABLES -A INPUT -i eth0 -p tcp --sport 22 -j ACCEPT
$IPTABLES -A INPUT -i eth1 -p tcp --sport 22 -j ACCEPT
$IPTABLES -A INPUT -i eth0 -p tcp --dport 22 -j ACCEPT
$IPTABLES -A INPUT -i eth1 -p tcp --dport 22 -j ACCEPT
echo "Allow ftp"
$IPTABLES -A INPUT -p tcp --sport 21 -m state --state ESTABLISHED -j
ACCEPT
$IPTABLES -A OUTPUT -p tcp --dport 21 -m state --state NEW,ESTABLISHED
-j ACCEPT
echo "Active ftp"
$IPTABLES -A INPUT -p tcp --sport 20 -m state --state
ESTABLISHED,RELATED -j ACCEPT
$IPTABLES -A OUTPUT -p tcp --dport 20 -m state --state ESTABLISHED -j
ACCEPT
echo "Passive ftp"
$IPTABLES -A INPUT -p tcp --sport 1024:65535 --dport 1024:65535 -m state
--state ESTABLISHED -j ACCEPT
$IPTABLES -A OUTPUT -p tcp --sport 1024:65535 --dport 1024:65535 -m
state --state ESTABLISHED,RELATED -j ACCEPT
echo "Allow DNS"
$IPTABLES -A INPUT -p tcp --sport 53 -j ACCEPT
$IPTABLES -A INPUT -p udp --sport 53 -j ACCEPT
$IPTABLES -A OUTPUT -p tcp --dport 53 -j ACCEPT
$IPTABLES -A OUTPUT -p udp --dport 53 -j ACCEPT
echo "Allow SFTP"
$IPTABLES -A OUTPUT -p tcp --dport 115 -j ACCEPT
$IPTABLES -A INPUT -p tcp --sport 115 -j ACCEPT
echo "Allow HTTP"
$IPTABLES -A OUTPUT -p tcp --dport 80 -j ACCEPT
$IPTABLES -A INPUT -p tcp --sport 80 -j ACCEPT
echo "Allow https"
$IPTABLES -A OUTPUT -p tcp --dport 443 -j ACCEPT
$IPTABLES -A INPUT -p tcp --sport 443 -j ACCEPT
echo "Rejecting all connections to 135:139"
$IPTABLES -N NETBIOS
$IPTABLES -A INPUT -p udp --sport 135:139 -j NETBIOS
$IPTABLES -A INPUT -p tcp --sport 135:139 -j NETBIOS
$IPTABLES -A INPUT -p udp --dport 135:139 -j NETBIOS
$IPTABLES -A INPUT -p tcp --dport 135:139 -j NETBIOS
$IPTABLES -A NETBIOS -j LOG --log-prefix "IPTABLES NETBIOS: "
$IPTABLES -A NETBIOS -j DROP
echo "Limit port 4665 traffic to PAUL"
$IPTABLES -N PAULS_STUFF
$IPTABLES -A FORWARD -p tcp -s $PAUL --dport 4665 -m limit --limit
1/hour -j PAULS_STUFF
$IPTABLES -A FORWARD -p udp -s $PAUL --dport 4665 -m limit --limit
1/hour -j PAULS_STUFF
$IPTABLES -A FORWARD -p udp -s $PAUL --sport 4665 -m limit --limit
1/hour -j PAULS_STUFF
$IPTABLES -A FORWARD -p tcp -s $PAUL --sport 4665 -m limit --limit
1/hour -j PAULS_STUFF
$IPTABLES -A PAULS_STUFF -j LOG --log-prefix "IPTABLES PAUL: "
$IPTABLES -A PAULS_STUFF -j ACCEPT
echo "Allowing SMTP"
$IPTABLES -A OUTPUT -p tcp --dport 25 -j ACCEPT
$IPTABLES -A INPUT -p tcp --sport 25 -j ACCEPT
echo "Allowing POP3"
$IPTABLES -A OUTPUT -p tcp --dport 110 -j ACCEPT
$IPTABLES -A INPUT -p tcp --sport 110 -j ACCEPT
echo "Allowing Ident"
$IPTABLES -A OUTPUT -p tcp --dport 113 -j ACCEPT
$IPTABLES -A INPUT -p tcp --sport 113 -j ACCEPT
echo "Allowing Netmeeting/MSN"
$IPTABLES -t nat -A PREROUTING -i eth0 -p tcp --dport 1863 -j \
REDIRECT --to-ports 1863
$IPTABLES -t nat -A PREROUTING -i eth0 -p tcp --dport 389 -j \
REDIRECT --to-ports 389
$IPTABLES -t nat -A PREROUTING -i eth0 -p tcp --dport 522 -j \
REDIRECT --to-ports 522
echo "Allowing EDonkey2k/Emule"
echo "See: http://www.emule-project.net/faq/ports.htm"
# should i use any -A FORWARD or PREROUTING here?
$IPTABLES -A OUTPUT -p tcp --dport 4661 -j ACCEPT
$IPTABLES -A INPUT -p tcp --sport 4661 -j ACCEPT
$IPTABLES -A OUTPUT -p tcp --dport 4662 -j ACCEPT
$IPTABLES -A INPUT -p tcp --sport 4662 -j ACCEPT
$IPTABLES -A OUTPUT -p udp --dport 4665 -j ACCEPT
$IPTABLES -A INPUT -p udp --sport 4665 -j ACCEPT
$IPTABLES -A OUTPUT -p udp --dport 4672 -j ACCEPT
$IPTABLES -A INPUT -p udp --sport 4672 -j ACCEPT
$IPTABLES -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT
$IPTABLES -A OUTPUT -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: New Script
2003-01-09 12:38 New Script mdew
@ 2003-01-09 13:38 ` Arnt Karlsen
2003-01-09 15:06 ` Anders Fugmann
1 sibling, 0 replies; 3+ messages in thread
From: Arnt Karlsen @ 2003-01-09 13:38 UTC (permalink / raw)
To: netfilter
On 10 Jan 2003 01:38:56 +1300,
mdew <mdew@mdew.dyndns.org> wrote in message
<1042115936.423.58.camel@nirvana>:
> Ok, after taking a few samples from scripts in the mailing list, Ive
> come up with this...hopefully my edonkey problem has been solved with
> this script. I havent actually tested this yet, Probably tomorrow (its
> a bit late)
>
> current Router setup.
> (Internet) 210.54.175.12->eth0---Router--->eth1 10.0.0.6 -=> 10.0.0.x
>
>
>
> #!/bin/bash
>
> IPTABLES="/sbin/iptables"
> PAUL="10.0.0.9"
> echo "1" > /proc/sys/net/ipv4/ip_forward
..the open barn door. Echo 0 here, and 1 again
at the very end of this script.
> echo "Executing The Firwall..."
> echo ""
> echo -n "Loading Modules..."
> /sbin/modprobe ip_conntrack_ftp
> /sbin/modprobe ip_conntrack_irc
> /sbin/modprobe ip_nat_irc
> /sbin/modprobe ip_nat_ftp
> /sbin/modprobe ipt_state
> /sbin/modprobe ipt_limit
> /sbin/modprobe ipt_LOG
> echo -n "Done"
>
> $IPTABLES -F INPUT
> $IPTABLES -F OUTPUT
> $IPTABLES -F FORWARD
> $IPTABLES -P INPUT ACCEPT
> $IPTABLES -P OUTPUT ACCEPT
>
> echo "Allow unlimited traffic on the loopback interface"
> $IPTABLES -A INPUT -i lo -j ACCEPT
> $IPTABLES -A OUTPUT -o lo -j ACCEPT
>
> echo "Refusing spoofed packets pretending to be from your IP address"
> $IPTABLES -A INPUT -s 210.54.175.12 -j DROP
>
> echo "Allow SSH"
> # Is this correct?
> $IPTABLES -A INPUT -i eth0 -p tcp --sport 22 -j ACCEPT
> $IPTABLES -A INPUT -i eth1 -p tcp --sport 22 -j ACCEPT
> $IPTABLES -A INPUT -i eth0 -p tcp --dport 22 -j ACCEPT
> $IPTABLES -A INPUT -i eth1 -p tcp --dport 22 -j ACCEPT
>
> echo "Allow ftp"
> $IPTABLES -A INPUT -p tcp --sport 21 -m state --state ESTABLISHED -j
> ACCEPT
> $IPTABLES -A OUTPUT -p tcp --dport 21 -m state --state NEW,ESTABLISHED
> -j ACCEPT
>
> echo "Active ftp"
> $IPTABLES -A INPUT -p tcp --sport 20 -m state --state
> ESTABLISHED,RELATED -j ACCEPT
> $IPTABLES -A OUTPUT -p tcp --dport 20 -m state --state ESTABLISHED -j
> ACCEPT
>
> echo "Passive ftp"
> $IPTABLES -A INPUT -p tcp --sport 1024:65535 --dport 1024:65535 -m
> state--state ESTABLISHED -j ACCEPT
> $IPTABLES -A OUTPUT -p tcp --sport 1024:65535 --dport 1024:65535 -m
> state --state ESTABLISHED,RELATED -j ACCEPT
>
> echo "Allow DNS"
> $IPTABLES -A INPUT -p tcp --sport 53 -j ACCEPT
> $IPTABLES -A INPUT -p udp --sport 53 -j ACCEPT
> $IPTABLES -A OUTPUT -p tcp --dport 53 -j ACCEPT
> $IPTABLES -A OUTPUT -p udp --dport 53 -j ACCEPT
>
> echo "Allow SFTP"
> $IPTABLES -A OUTPUT -p tcp --dport 115 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 115 -j ACCEPT
>
> echo "Allow HTTP"
> $IPTABLES -A OUTPUT -p tcp --dport 80 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 80 -j ACCEPT
>
> echo "Allow https"
> $IPTABLES -A OUTPUT -p tcp --dport 443 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 443 -j ACCEPT
>
> echo "Rejecting all connections to 135:139"
> $IPTABLES -N NETBIOS
> $IPTABLES -A INPUT -p udp --sport 135:139 -j NETBIOS
> $IPTABLES -A INPUT -p tcp --sport 135:139 -j NETBIOS
> $IPTABLES -A INPUT -p udp --dport 135:139 -j NETBIOS
> $IPTABLES -A INPUT -p tcp --dport 135:139 -j NETBIOS
> $IPTABLES -A NETBIOS -j LOG --log-prefix "IPTABLES NETBIOS: "
> $IPTABLES -A NETBIOS -j DROP
>
> echo "Limit port 4665 traffic to PAUL"
> $IPTABLES -N PAULS_STUFF
> $IPTABLES -A FORWARD -p tcp -s $PAUL --dport 4665 -m limit --limit
> 1/hour -j PAULS_STUFF
> $IPTABLES -A FORWARD -p udp -s $PAUL --dport 4665 -m limit --limit
> 1/hour -j PAULS_STUFF
> $IPTABLES -A FORWARD -p udp -s $PAUL --sport 4665 -m limit --limit
> 1/hour -j PAULS_STUFF
> $IPTABLES -A FORWARD -p tcp -s $PAUL --sport 4665 -m limit --limit
> 1/hour -j PAULS_STUFF
> $IPTABLES -A PAULS_STUFF -j LOG --log-prefix "IPTABLES PAUL: "
> $IPTABLES -A PAULS_STUFF -j ACCEPT
>
> echo "Allowing SMTP"
> $IPTABLES -A OUTPUT -p tcp --dport 25 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 25 -j ACCEPT
>
> echo "Allowing POP3"
> $IPTABLES -A OUTPUT -p tcp --dport 110 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 110 -j ACCEPT
>
> echo "Allowing Ident"
> $IPTABLES -A OUTPUT -p tcp --dport 113 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 113 -j ACCEPT
>
> echo "Allowing Netmeeting/MSN"
> $IPTABLES -t nat -A PREROUTING -i eth0 -p tcp --dport 1863 -j \
> REDIRECT --to-ports 1863
> $IPTABLES -t nat -A PREROUTING -i eth0 -p tcp --dport 389 -j \
> REDIRECT --to-ports 389
> $IPTABLES -t nat -A PREROUTING -i eth0 -p tcp --dport 522 -j \
> REDIRECT --to-ports 522
>
> echo "Allowing EDonkey2k/Emule"
> echo "See: http://www.emule-project.net/faq/ports.htm"
> # should i use any -A FORWARD or PREROUTING here?
> $IPTABLES -A OUTPUT -p tcp --dport 4661 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 4661 -j ACCEPT
> $IPTABLES -A OUTPUT -p tcp --dport 4662 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 4662 -j ACCEPT
> $IPTABLES -A OUTPUT -p udp --dport 4665 -j ACCEPT
> $IPTABLES -A INPUT -p udp --sport 4665 -j ACCEPT
> $IPTABLES -A OUTPUT -p udp --dport 4672 -j ACCEPT
> $IPTABLES -A INPUT -p udp --sport 4672 -j ACCEPT
>
> $IPTABLES -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT
> $IPTABLES -A OUTPUT -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT
>
>
>
--
..med vennlig hilsen = with Kind Regards from Arnt... ;-)
...with a number of polar bear hunters in his ancestry...
Scenarios always come in sets of three:
best case, worst case, and just in case.
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: New Script
2003-01-09 12:38 New Script mdew
2003-01-09 13:38 ` Arnt Karlsen
@ 2003-01-09 15:06 ` Anders Fugmann
1 sibling, 0 replies; 3+ messages in thread
From: Anders Fugmann @ 2003-01-09 15:06 UTC (permalink / raw)
To: mdew; +Cc: netfilter
mdew wrote:
> Ok, after taking a few samples from scripts in the mailing list, Ive
> come up with this...hopefully my edonkey problem has been solved with
> this script. I havent actually tested this yet, Probably tomorrow (its a
> bit late)
Next time - Test first, then post.
>
> current Router setup.
> (Internet) 210.54.175.12->eth0---Router--->eth1 10.0.0.6 -=> 10.0.0.x
>
>
> #!/bin/bash
>
> IPTABLES="/sbin/iptables"
> PAUL="10.0.0.9"
> echo "1" > /proc/sys/net/ipv4/ip_forward
>
> echo "Executing The Firwall..."
> echo ""
> echo -n "Loading Modules..."
> /sbin/modprobe ip_conntrack_ftp
> /sbin/modprobe ip_conntrack_irc
> /sbin/modprobe ip_nat_irc
> /sbin/modprobe ip_nat_ftp
> /sbin/modprobe ipt_state
> /sbin/modprobe ipt_limit
> /sbin/modprobe ipt_LOG
> echo -n "Done"
>
> $IPTABLES -F INPUT
> $IPTABLES -F OUTPUT
> $IPTABLES -F FORWARD
I would recommend that you set the default policy here to DENY and add
the rules:
$IPTABLES -a FORWARD -i eth0 -o eth1 -m state --state \
RELATED,ESTABLISHED -j ACCEPT
$IPTABLES -a FORWARD -o eth0 -i eth1 -j ACCEPT
to allow machines behind to firewall to comminucate freely with servers
on the internet.
> $IPTABLES -P INPUT ACCEPT
Uh. Dont allow anything on the INPUT chain.
> $IPTABLES -P OUTPUT ACCEPT
>
> echo "Allow unlimited traffic on the loopback interface"
> $IPTABLES -A INPUT -i lo -j ACCEPT
> $IPTABLES -A OUTPUT -o lo -j ACCEPT
>
> echo "Refusing spoofed packets pretending to be from your IP address"
> $IPTABLES -A INPUT -s 210.54.175.12 -j DROP
>
> echo "Allow SSH"
> # Is this correct?
> $IPTABLES -A INPUT -i eth0 -p tcp --sport 22 -j ACCEPT
> $IPTABLES -A INPUT -i eth1 -p tcp --sport 22 -j ACCEPT
> $IPTABLES -A INPUT -i eth0 -p tcp --dport 22 -j ACCEPT
> $IPTABLES -A INPUT -i eth1 -p tcp --dport 22 -j ACCEPT
>
> echo "Allow ftp"
> $IPTABLES -A INPUT -p tcp --sport 21 -m state --state ESTABLISHED -j
> ACCEPT
> $IPTABLES -A OUTPUT -p tcp --dport 21 -m state --state NEW,ESTABLISHED
> -j ACCEPT
>
> echo "Active ftp"
> $IPTABLES -A INPUT -p tcp --sport 20 -m state --state
> ESTABLISHED,RELATED -j ACCEPT
> $IPTABLES -A OUTPUT -p tcp --dport 20 -m state --state ESTABLISHED -j
> ACCEPT
>
> echo "Passive ftp"
> $IPTABLES -A INPUT -p tcp --sport 1024:65535 --dport 1024:65535 -m state
> --state ESTABLISHED -j ACCEPT
> $IPTABLES -A OUTPUT -p tcp --sport 1024:65535 --dport 1024:65535 -m
> state --state ESTABLISHED,RELATED -j ACCEPT
>
> echo "Allow DNS"
> $IPTABLES -A INPUT -p tcp --sport 53 -j ACCEPT
> $IPTABLES -A INPUT -p udp --sport 53 -j ACCEPT
> $IPTABLES -A OUTPUT -p tcp --dport 53 -j ACCEPT
> $IPTABLES -A OUTPUT -p udp --dport 53 -j ACCEPT
>
> echo "Allow SFTP"
> $IPTABLES -A OUTPUT -p tcp --dport 115 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 115 -j ACCEPT
>
> echo "Allow HTTP"
> $IPTABLES -A OUTPUT -p tcp --dport 80 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 80 -j ACCEPT
>
> echo "Allow https"
> $IPTABLES -A OUTPUT -p tcp --dport 443 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 443 -j ACCEPT
>
> echo "Rejecting all connections to 135:139"
> $IPTABLES -N NETBIOS
> $IPTABLES -A INPUT -p udp --sport 135:139 -j NETBIOS
> $IPTABLES -A INPUT -p tcp --sport 135:139 -j NETBIOS
> $IPTABLES -A INPUT -p udp --dport 135:139 -j NETBIOS
> $IPTABLES -A INPUT -p tcp --dport 135:139 -j NETBIOS
> $IPTABLES -A NETBIOS -j LOG --log-prefix "IPTABLES NETBIOS: "
> $IPTABLES -A NETBIOS -j DROP
>
> echo "Limit port 4665 traffic to PAUL"
> $IPTABLES -N PAULS_STUFF
> $IPTABLES -A FORWARD -p tcp -s $PAUL --dport 4665 -m limit --limit
> 1/hour -j PAULS_STUFF
> $IPTABLES -A FORWARD -p udp -s $PAUL --dport 4665 -m limit --limit
> 1/hour -j PAULS_STUFF
> $IPTABLES -A FORWARD -p udp -s $PAUL --sport 4665 -m limit --limit
> 1/hour -j PAULS_STUFF
> $IPTABLES -A FORWARD -p tcp -s $PAUL --sport 4665 -m limit --limit
> 1/hour -j PAULS_STUFF
> $IPTABLES -A PAULS_STUFF -j LOG --log-prefix "IPTABLES PAUL: "
> $IPTABLES -A PAULS_STUFF -j ACCEPT
What are you trying here? Linit should not be used as traffic shaping.
Please use programs in the iproute2 package instead. It will handle
things much better.
>
> echo "Allowing SMTP"
> $IPTABLES -A OUTPUT -p tcp --dport 25 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 25 -j ACCEPT
>
> echo "Allowing POP3"
> $IPTABLES -A OUTPUT -p tcp --dport 110 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 110 -j ACCEPT
>
> echo "Allowing Ident"
> $IPTABLES -A OUTPUT -p tcp --dport 113 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 113 -j ACCEPT
>
> echo "Allowing Netmeeting/MSN"
> $IPTABLES -t nat -A PREROUTING -i eth0 -p tcp --dport 1863 -j \
> REDIRECT --to-ports 1863
> $IPTABLES -t nat -A PREROUTING -i eth0 -p tcp --dport 389 -j \
> REDIRECT --to-ports 389
> $IPTABLES -t nat -A PREROUTING -i eth0 -p tcp --dport 522 -j \
> REDIRECT --to-ports 522
>
> echo "Allowing EDonkey2k/Emule"
> echo "See: http://www.emule-project.net/faq/ports.htm"
> # should i use any -A FORWARD or PREROUTING here?
> $IPTABLES -A OUTPUT -p tcp --dport 4661 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 4661 -j ACCEPT
> $IPTABLES -A OUTPUT -p tcp --dport 4662 -j ACCEPT
> $IPTABLES -A INPUT -p tcp --sport 4662 -j ACCEPT
> $IPTABLES -A OUTPUT -p udp --dport 4665 -j ACCEPT
> $IPTABLES -A INPUT -p udp --sport 4665 -j ACCEPT
> $IPTABLES -A OUTPUT -p udp --dport 4672 -j ACCEPT
> $IPTABLES -A INPUT -p udp --sport 4672 -j ACCEPT
I'm not sure what you want here. But if all you want is to allow users
to connect to server on the internet on port 4672, then its covered be
the rules below.
>
> $IPTABLES -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT
For the protocols ssh, ftp, http, dns, smtp, pop3 and ident you can
delete all the rules conserning these, as the line above take care of
all that.
> $IPTABLES -A OUTPUT -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT
This is not needed, as the policy on the OUTPUT chain is already ACCEPT.
Regards
Anders Fugmann
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2003-01-09 15:06 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-01-09 12:38 New Script mdew
2003-01-09 13:38 ` Arnt Karlsen
2003-01-09 15:06 ` Anders Fugmann
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.