All of lore.kernel.org
 help / color / mirror / Atom feed
From: Droebbel <droebbel.melta@gmx.de>
To: linux-kernel@vger.kernel.org
Subject: [Problem] slow write to dvd-ram since 2.6.7-bk8
Date: Sun, 13 Feb 2005 14:36:34 +0100	[thread overview]
Message-ID: <1108301794.9280.18.camel@localhost.localdomain> (raw)

On recent kernels, writing to DVD-RAM is much slower than to be
expected. A 3x Writer should do about 1.9MB/s including automatic
verify. This is what I get with 2.6.7 up to bk7. However, from 2.6.7-bk8
to 2.6.10 write speed is as low as 600 to 1000 kB/s. The drive's head
jumps a lot more with these kernels. Reading is ok.

I tested UDF and ext2 filesystems,
DMA is ok according to hdparm,
I set taskfile-io on and off when building the kernels,
and I compared the settings for the io-scheduler.

The drive is connected via onboard via82xx ide or usb2 external (both
works perfectly with hd).

The drive is a LG GSA-4163B; a GSA-4120 had the same problem as far as I
remember.

Medium: Panasonic 3x

Could not find any kernel error messages.


For testing the 2.6.7-bk2 to bk14 I took the cdrom.c from bk15, as the
cdrom devices wer marked read-only without.


As I am not a programmer, I failed to track down the problem any
further, but I'll do my best if I get any hints or advice where to
search.

David

--------------

**hdparm output:**

 Model=HL-DT-ST DVDRAM GSA-4163B, FwRev=A101, SerialNo=K764C241904
 Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
 RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
 BuffType=unknown, BuffSize=0kB, MaxMultSect=0
 (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 *udma2
 AdvancedPM=no
 Drive conforms to: device does not report version:

 * signifies the current active mode


ATAPI CD-ROM, with removable media
        Model Number:       HL-DT-ST DVDRAM GSA-4163B
        Serial Number:      K764C241904
        Firmware Revision:  A101
Standards:
        Likely used CD-ROM ATAPI-1
Configuration:
        DRQ response: 50us.
        Packet size: 12 bytes
Capabilities:
        LBA, IORDY(can be disabled)
        DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=120ns  IORDY flow control=120ns
HW reset results:
        CBLID- above Vih
        Device num = 0

-----------------

Additional information:
**Output of ver_linux on the testing system with 2.6.7-bk8:**

Linux schlupp 2.6.7-bk8 #6 Sat Feb 12 22:28:31 CET 2005 i686 GNU/Linux

Gnu C                  3.3.5
Gnu make               3.80
binutils               2.15
util-linux             2.12p
mount                  2.12p
module-init-tools      3.1
e2fsprogs              1.35
jfsutils               1.1.6
xfsprogs               2.6.20
PPP                    2.4.2
Linux C Library        2.3.2
Dynamic linker (ldd)   2.3.2
Procps                 3.2.4
Net-tools              1.60
Console-tools          0.2.3
Sh-utils               5.2.1
Modules Loaded         ehci_hcd uhci_hcd sata_via libata md dm_mod
parport_pc lp parport sr_mod

---------------

**ioports**

0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial
0808-080b : ACPI timer
0810-0815 : ACPI CPU throttle
0cf8-0cff : PCI conf1
b000-b0ff : 0000:00:0e.0
b400-b407 : 0000:00:0e.0
b800-b81f : 0000:00:10.0
  b800-b81f : uhci_hcd
c000-c01f : 0000:00:10.1
  c000-c01f : uhci_hcd
c400-c41f : 0000:00:10.2
  c400-c41f : uhci_hcd
c800-c81f : 0000:00:10.3
  c800-c81f : uhci_hcd
cc00-cc7f : 0000:00:07.0
d000-d0ff : 0000:00:0f.0
  d000-d0ff : sata_via
d400-d40f : 0000:00:0f.0
  d400-d40f : sata_via
d800-d803 : 0000:00:0f.0
  d800-d803 : sata_via
dc00-dcff : 0000:00:0a.0
e000-e007 : 0000:00:0f.0
  e000-e007 : sata_via
e400-e403 : 0000:00:0f.0
  e400-e403 : sata_via
e800-e807 : 0000:00:0f.0
  e800-e807 : sata_via
ec00-ecff : 0000:00:0c.0
fc00-fc0f : 0000:00:0f.1
  fc00-fc07 : ide0
  fc08-fc0f : ide1

-----------------

**iomem**

00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cb7ff : Video ROM
000f0000-000fffff : System ROM
00100000-1ff2ffff : System RAM
  00100000-0035f07d : Kernel code
  0035f07e-004413ff : Kernel data
1ff30000-1ff3ffff : ACPI Tables
1ff40000-1ffeffff : ACPI Non-volatile Storage
1fff0000-1fffffff : reserved
e4e00000-f4dfffff : PCI Bus #01
  e8000000-efffffff : 0000:01:00.0
f4f00000-f70fffff : PCI Bus #01
  f6000000-f6ffffff : 0000:01:00.0
f7700000-f77007ff : 0000:00:07.0
f7b00000-f7b03fff : 0000:00:0a.0
f7d00000-f7d000ff : 0000:00:0c.0
f7e00000-f7e000ff : 0000:00:0e.0
f7f00000-f7f000ff : 0000:00:10.4
  f7f00000-f7f000ff : ehci_hcd
f8000000-fbffffff : 0000:00:00.0
fff80000-ffffffff : reserved

-----------------

**lspci**

0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP]
Host Bridge (rev 01)
        Subsystem: Asustek Computer, Inc.: Unknown device 80a3
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
        Latency: 8
        Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: <available only to root>

0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge
[K8T800 South] (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: f4f00000-f70fffff
        Prefetchable memory behind bridge: e4e00000-f4dfffff
        BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
        Capabilities: <available only to root>

0000:00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80) (prog-if 10 [OHCI])
        Subsystem: Asustek Computer, Inc.: Unknown device 808a
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (8000ns max), Cache Line Size: 0x40 (256 bytes)
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at f7700000 (32-bit, non-prefetchable)
[size=2K]
        Region 1: I/O ports at cc00 [size=128]
        Capabilities: <available only to root>

0000:00:0a.0 Ethernet controller: Marvell Technology Group Ltd. Yukon
Gigabit Ethernet 10/100/1000Base-T Adapter (rev 13)
        Subsystem: Asustek Computer, Inc.: Unknown device 811a
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 0x40 (256
bytes)
        Interrupt: pin A routed to IRQ 17
        Region 0: Memory at f7b00000 (32-bit, non-prefetchable)
[size=16K]
        Region 1: I/O ports at dc00 [size=256]
        Expansion ROM at f7a00000 [disabled] [size=128K]
        Capabilities: <available only to root>

0000:00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Realtek Semiconductor Co., Ltd. RT8139
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 17
        Region 0: I/O ports at ec00 [size=256]
        Region 1: Memory at f7d00000 (32-bit, non-prefetchable)
[size=256]
        Expansion ROM at f7c00000 [disabled] [size=64K]
        Capabilities: <available only to root>

0000:00:0e.0 Communication controller: Lucent Microelectronics 56k
WinModem (rev 01)
        Subsystem: Lucent Microelectronics LT WinModem 56k Data+Fax
+Voice+Dsvd
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0 (63000ns min, 3500ns max)
        Interrupt: pin A routed to IRQ 7
        Region 0: Memory at f7e00000 (32-bit, non-prefetchable)
[size=256]
        Region 1: I/O ports at b400 [size=8]
        Region 2: I/O ports at b000 [size=256]
        Capabilities: <available only to root>

0000:00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA
RAID Controller (rev 80)
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Interrupt: pin B routed to IRQ 20
        Region 0: I/O ports at e800 [size=8]
        Region 1: I/O ports at e400 [size=4]
        Region 2: I/O ports at e000 [size=8]
        Region 3: I/O ports at d800 [size=4]
        Region 4: I/O ports at d400 [size=16]
        Region 5: I/O ports at d000 [size=256]
        Capabilities: <available only to root>

0000:00:0f.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32
        Interrupt: pin A routed to IRQ 20
        Region 4: I/O ports at fc00 [size=16]
        Capabilities: <available only to root>

0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x40 (256 bytes)
        Interrupt: pin A routed to IRQ 21
        Region 4: I/O ports at b800 [size=32]
        Capabilities: <available only to root>

0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x40 (256 bytes)
        Interrupt: pin A routed to IRQ 21
        Region 4: I/O ports at c000 [size=32]
        Capabilities: <available only to root>

0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x40 (256 bytes)
        Interrupt: pin B routed to IRQ 21
        Region 4: I/O ports at c400 [size=32]
        Capabilities: <available only to root>

0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x40 (256 bytes)
        Interrupt: pin B routed to IRQ 21
        Region 4: I/O ports at c800 [size=32]
        Capabilities: <available only to root>

0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
(prog-if 20 [EHCI])
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x40 (256 bytes)
        Interrupt: pin C routed to IRQ 21
        Region 0: Memory at f7f00000 (32-bit, non-prefetchable)
[size=256]
        Capabilities: <available only to root>

0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
[K8T800 South]
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: <available only to root>

0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Capabilities: <available only to root>

0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

0000:01:00.0 VGA compatible controller: nVidia Corporation NV11
[GeForce2 MX/MX 400] (rev a1) (prog-if 00 [VGA])
        Subsystem: CardExpert Technology: Unknown device 0001
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 248 (1250ns min, 250ns max)
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at f6000000 (32-bit, non-prefetchable)
[size=16M]
        Region 1: Memory at e8000000 (32-bit, prefetchable) [size=128M]
        Expansion ROM at f7000000 [disabled] [size=64K]
        Capabilities: <available only to root>

dm@schlupp:~$ sudo lspci -vvv
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP]
Host Bridge (rev 01)
        Subsystem: Asustek Computer, Inc.: Unknown device 80a3
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
        Latency: 8
        Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: [80] AGP version 3.5
                Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x4
                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW-
Rate=x4
        Capabilities: [c0] #08 [0060]
        Capabilities: [68] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] #08 [8001]

0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge
[K8T800 South] (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: f4f00000-f70fffff
        Prefetchable memory behind bridge: e4e00000-f4dfffff
        BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80) (prog-if 10 [OHCI])
        Subsystem: Asustek Computer, Inc.: Unknown device 808a
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (8000ns max), Cache Line Size: 0x40 (256 bytes)
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at f7700000 (32-bit, non-prefetchable)
[size=2K]
        Region 1: I/O ports at cc00 [size=128]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0a.0 Ethernet controller: Marvell Technology Group Ltd. Yukon
Gigabit Ethernet 10/100/1000Base-T Adapter (rev 13)
        Subsystem: Asustek Computer, Inc.: Unknown device 811a
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 0x40 (256
bytes)
        Interrupt: pin A routed to IRQ 17
        Region 0: Memory at f7b00000 (32-bit, non-prefetchable)
[size=16K]
        Region 1: I/O ports at dc00 [size=256]
        Expansion ROM at f7a00000 [disabled] [size=128K]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [50] Vital Product Data

0000:00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Realtek Semiconductor Co., Ltd. RT8139
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 17
        Region 0: I/O ports at ec00 [size=256]
        Region 1: Memory at f7d00000 (32-bit, non-prefetchable)
[size=256]
        Expansion ROM at f7c00000 [disabled] [size=64K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1
+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0e.0 Communication controller: Lucent Microelectronics 56k
WinModem (rev 01)
        Subsystem: Lucent Microelectronics LT WinModem 56k Data+Fax
+Voice+Dsvd
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0 (63000ns min, 3500ns max)
        Interrupt: pin A routed to IRQ 7
        Region 0: Memory at f7e00000 (32-bit, non-prefetchable)
[size=256]
        Region 1: I/O ports at b400 [size=8]
        Region 2: I/O ports at b000 [size=256]
        Capabilities: [f8] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA
RAID Controller (rev 80)
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Interrupt: pin B routed to IRQ 20
        Region 0: I/O ports at e800 [size=8]
        Region 1: I/O ports at e400 [size=4]
        Region 2: I/O ports at e000 [size=8]
        Region 3: I/O ports at d800 [size=4]
        Region 4: I/O ports at d400 [size=16]
        Region 5: I/O ports at d000 [size=256]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0f.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32
        Interrupt: pin A routed to IRQ 20
        Region 4: I/O ports at fc00 [size=16]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x40 (256 bytes)
        Interrupt: pin A routed to IRQ 21
        Region 4: I/O ports at b800 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x40 (256 bytes)
        Interrupt: pin A routed to IRQ 21
        Region 4: I/O ports at c000 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x40 (256 bytes)
        Interrupt: pin B routed to IRQ 21
        Region 4: I/O ports at c400 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81) (prog-if 00 [UHCI])
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x40 (256 bytes)
        Interrupt: pin B routed to IRQ 21
        Region 4: I/O ports at c800 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
(prog-if 20 [EHCI])
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x40 (256 bytes)
        Interrupt: pin C routed to IRQ 21
        Region 0: Memory at f7f00000 (32-bit, non-prefetchable)
[size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1
+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
[K8T800 South]
        Subsystem: Asustek Computer, Inc. A7V600 motherboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Capabilities: [80] #08 [2101]

0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

0000:01:00.0 VGA compatible controller: nVidia Corporation NV11
[GeForce2 MX/MX 400] (rev a1) (prog-if 00 [VGA])
        Subsystem: CardExpert Technology: Unknown device 0001
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 248 (1250ns min, 250ns max)
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at f6000000 (32-bit, non-prefetchable)
[size=16M]
        Region 1: Memory at e8000000 (32-bit, prefetchable) [size=128M]
        Expansion ROM at f7000000 [disabled] [size=64K]
        Capabilities: [60] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [44] AGP version 2.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
                Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit-
FW- Rate=x4





             reply	other threads:[~2005-02-13 13:39 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2005-02-13 13:36 Droebbel [this message]
2005-02-13 14:26 ` [Problem] slow write to dvd-ram since 2.6.7-bk8 Wakko Warner
2005-02-14  8:53   ` Tino Keitel
2005-02-14 10:28     ` Droebbel
     [not found]     ` <1108376734.9495.8.camel@localhost.localdomain>
     [not found]       ` <20050214105332.GA7163@dose.home.local>
2005-02-14 12:34         ` Droebbel
     [not found]         ` <1108379351.9495.22.camel@localhost.localdomain>
     [not found]           ` <20050214111819.GA7691@dose.home.local>
2005-02-16 21:55             ` Droebbel
2005-02-16 22:29               ` Droebbel
2005-02-17 23:10                 ` Tino Keitel
2005-02-18 22:21                   ` Droebbel

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1108301794.9280.18.camel@localhost.localdomain \
    --to=droebbel.melta@gmx.de \
    --cc=linux-kernel@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.