From: Droebbel <droebbel.melta@gmx.de>
To: Tino Keitel <tino.keitel@gmx.de>
Cc: linux-kernel@vger.kernel.org
Subject: Re: [Problem] slow write to dvd-ram since 2.6.7-bk8
Date: Fri, 18 Feb 2005 23:21:10 +0100 [thread overview]
Message-ID: <1108765270.14370.22.camel@localhost.localdomain> (raw)
In-Reply-To: <20050217231048.GA4363@dose.home.local>
On Fr, 2005-02-18 at 00:10 +0100, Tino Keitel wrote:
>On Wed, Feb 16, 2005 at 23:29:24 +0100, Droebbel wrote:
>> On Mi, 2005-02-16 at 22:55 +0100, Droebbel wrote:
>>
>> >The vmscan-dont-reclaim-too-many-pages.patch led to the said reduction
>> >of writing speed. I reverse-applied it to 2.6.8.1, where it seems to
>> >solve the problem.
>>
>> Sorry, have to correct that: it seemed to help at my tests with dd
>> (write 1G of zeroes to a file). Copying a file with mc still shows
>> around 1.4MB/s. Could be worse, but is definitely not ok. It *is* better
>> with 2.6.7.
>
>Here are some numbers with my setup. I always wrote 1 GB of data to the
>same DVD-RAM disc (EMTEC), to the device directly and to a fresh ext2
>on
>the disc.
>
>kernel 2.6.10:
>
>$ time { sudo dd if=/dev/zero of=bigfile bs=64k count=16000 ; sync ; }
>
>real 32m5.025s
>
>$ time {sudo dd if=/dev/zero of=/dev/cdrom bs=64k count=16000 ; sync ;}
>
>real 29m41.980s
>
>kernel 2.6.7:
>
>$ time { sudo dd if=/dev/zero of=bigfile bs=64k count=16000 ; sync ; }
>
>real 13m23.688s
>
>$ time {sudo dd if=/dev/zero of=/dev/cdrom bs=64k count=16000 ; sync ;}
>
>real 13m14.609s
This is what I get:
2.6.8 to 2.6.10: about 30 min. I think that's clear now. I did not run
any mre test with that.
2.6.7 gives less than 10 minutes.
Reverse-Patched 2.6.8.1 and 2.6.10 about 9-11 min.
But what I think is interesting: Other than with 2.6.7, with my 2.6.10
the result seems to be highly dependent on other io activities. I came
to test that when I saw that writing to dvd-ram slowed down when reading
from a cdrom at the same time. System disk, cdrom and dvd-ram are
connected by buses as independent as possible: hda, hdd and scd0 via
on-chip ide2. hdc is inactive and spun down at the times of testing.
Some results (same command as yours, but writing to file only):
2.6.8.1 with vmscan-dont-reclaim-too-many-pages.patch
and vmscan-scan-sanity.patch reversed:
real 9m17.389s
real 10m11.271s
(run twice)
2.6.10, both patches reversed:
real 10m26.374s
same kernel, some io and high (but niced) system load by reading from
hda and gzipping into /dev/null
real 21m46.795s
same kernel, some io and low load by reading from cdrom (raw read with
dd as well) into /dev/null
real 22m11.639s
2.6.7 vanilla, some io and low load by reading from cdrom (raw read with
dd as well) into /dev/null
real 5m58.092
That's too fast - impossible on 3x media with verification. I'll check
that again. But it *really* seemed to be fast.
I also hat the impression that my tests with 2.6.10 and 2.6.8.1 were
much more promising when run from a rather basic testing system without
X, a bit closer to the 2.6.7 results. Haven't got time to check that
till monday. All the above results except the 2.6.7 are from Ubuntu
(Hoary) Systems with X and Gnome running.
Regards
David
prev parent reply other threads:[~2005-02-18 22:21 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-02-13 13:36 [Problem] slow write to dvd-ram since 2.6.7-bk8 Droebbel
2005-02-13 14:26 ` Wakko Warner
2005-02-14 8:53 ` Tino Keitel
2005-02-14 10:28 ` Droebbel
[not found] ` <1108376734.9495.8.camel@localhost.localdomain>
[not found] ` <20050214105332.GA7163@dose.home.local>
2005-02-14 12:34 ` Droebbel
[not found] ` <1108379351.9495.22.camel@localhost.localdomain>
[not found] ` <20050214111819.GA7691@dose.home.local>
2005-02-16 21:55 ` Droebbel
2005-02-16 22:29 ` Droebbel
2005-02-17 23:10 ` Tino Keitel
2005-02-18 22:21 ` Droebbel [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1108765270.14370.22.camel@localhost.localdomain \
--to=droebbel.melta@gmx.de \
--cc=linux-kernel@vger.kernel.org \
--cc=tino.keitel@gmx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.