From: Peter Zijlstra <peterz@infradead.org>
To: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>, Jack Steiner <steiner@sgi.com>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
Thomas Gleixner <tglx@linutronix.de>,
"H. Peter Anvin" <hpa@zytor.com>
Subject: Re: tip: patches in git for irq and numa
Date: Mon, 18 May 2009 17:11:17 +0200 [thread overview]
Message-ID: <1242659477.26820.433.camel@twins> (raw)
In-Reply-To: <4A1178D5.5050900@kernel.org>
On Mon, 2009-05-18 at 08:03 -0700, Yinghai Lu wrote:
> Peter Zijlstra wrote:
>
> > commit b9c61b70075c87a8612624736faf4a2de5b1ed30
> > Author: Yinghai Lu <yinghai@kernel.org>
> > Date: Wed May 6 10:10:06 2009 -0700
> >
> > x86/pci: update pirq_enable_irq() to setup io apic routing
> >
> > So we can set io apic routing only when enabling the device irq.
> >
> > This is advantageous for IRQ descriptor allocation affinity: if we set up
> > the IO-APIC entry later, we have a chance to allocate the IRQ descriptor
> > later and know which device it is on and can set affinity accordingly.
> >
> > [ Impact: standardize/enhance irq-enabling sequence for mptable irqs ]
>
> can you post whole bootlog?
See below
> need to figure out 32bit/64bit? ACPI is disabled? MPtable is used?
64bit, default acpi default mptable
> also please check if pci=routeirq help to fix the problem.
It does not.
[ 0.000000] Linux version 2.6.30-rc3 (root@twins) (gcc version 4.3.1 20080510 (prerelease) (GCC) ) #984 SMP PREEMPT Mon May 18 15:46:49 CEST 2009
[ 0.000000] Command line: ro root=UUID=2678f5ee-ec1c-4be4-9fdd-ee4f1de115fa debug ignore_loglevel sysrq_always_enabled console=ttyS0,115200 earlyprintk=serial,ttyS0,115200rq_always_enabled console=ttyS0,115200 earlyprintk=seria
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel [Linux-bzImage, setup=0x2e00, size=0x27cbb0]
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009d800 (usable)
[ 0.000000] BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
[ 0.000000] BIOS-e820: 000000007fff0000 - 000000007fffe000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fffe000 - 0000000080000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec03000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] debug: ignoring loglevel setting.
[ 0.000000] console [earlyser0] enabled
[ 0.000000] DMI 2.3 present.
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)-2.6.30-rc3.img
[ 0.000000] last_pfn = 0x7fff0 max_arch_pfn = 0x100000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask FF80000000 write-back
[ 0.000000] 1 disabled
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] init_memory_mapping: 0000000000000000-000000007fff0000
[ 0.000000] 0000000000 - 007fe00000 page 2M
[ 0.000000] 007fe00000 - 007fff0000 page 4k
[ 0.000000] kernel direct mapping tables up to 7fff0000 @ 10000-14000
[ 0.000000] RAMDISK: 37d54000 - 37fef31b
[ 0.000000] ACPI: RSDP 00000000000f7470 00024 (v02 ACPIAM)
[ 0.000000] ACPI: XSDT 000000007fff0100 00044 (v01 A M I OEMXSDT 09000625 MSFT 00000097)
[ 0.000000] ACPI: FACP 000000007fff0290 000F4 (v03 A M I OEMFACP 09000625 MSFT 00000097)
[ 0.000000] ACPI: DSDT 000000007fff0400 03018 (v01 0AAAA 0AAAA000 00000000 INTL 02002026)
[ 0.000000] ACPI: FACS 000000007fffe000 00040
[ 0.000000] ACPI: APIC 000000007fff0390 00070 (v01 A M I OEMAPIC 09000625 MSFT 00000097)
[ 0.000000] ACPI: OEMB 000000007fffe040 00056 (v01 A M I AMI_OEM 09000625 MSFT 00000097)
[ 0.000000] ACPI: SSDT 000000007fff3420 00248 (v01 A M I POWERNOW 00000001 AMD 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 007fff0000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0000200000 - 0001231e10] TEXT DATA BSS ==> [0000200000 - 0001231e10]
[ 0.000000] #3 [0037d54000 - 0037fef31b] RAMDISK ==> [0037d54000 - 0037fef31b]
[ 0.000000] #4 [000009d800 - 0000100000] BIOS reserved ==> [000009d800 - 0000100000]
[ 0.000000] #5 [0001232000 - 0001232200] BRK ==> [0001232000 - 0001232200]
[ 0.000000] #6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
[ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780
[ 0.000000] [ffffe20000000000-ffffe200033fffff] PMD -> [ffff880001400000-ffff8800047fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009d
[ 0.000000] 0: 0x00000100 -> 0x0007fff0
[ 0.000000] On node 0 totalpages: 524157
[ 0.000000] DMA zone: 104 pages used for memmap
[ 0.000000] DMA zone: 103 pages reserved
[ 0.000000] DMA zone: 3774 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 13208 pages used for memmap
[ 0.000000] DMA32 zone: 506968 pages, LIFO batch:31
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] ACPI: PM-Timer IO Port: 0x508
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-15
[ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec01000] gsi_base[16])
[ 0.000000] IOAPIC[1]: apic_id 3, version 0, address 0xfec01000, GSI 16-31
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec02000] gsi_base[32])
[ 0.000000] IOAPIC[2]: apic_id 4, version 0, address 0xfec02000, GSI 32-47
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 48
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
[ 0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 473 pages at ffff880004800000, static data 1907424 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 510742
[ 0.000000] Kernel command line: ro root=UUID=2678f5ee-ec1c-4be4-9fdd-ee4f1de115fa debug ignore_loglevel sysrq_always_enabled console=ttyS0,115200 earlyprintk=serial,ttyS0,115200
[ 0.000000] debug: sysrq always enabled.
[ 0.000000] Initializing CPU#0
[ 0.000000] NR_IRQS:512
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Fast TSC calibration failed
[ 0.000000] TSC: PIT calibration matches PMTIMER. 1 loops
[ 0.000000] Detected 2393.995 MHz processor.
[ 0.000999] Console: colour VGA+ 80x25
[ 0.000999] console handover: boot [earlyser0] -> real [ttyS0]
[ 0.000999] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000999] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000999] ... MAX_LOCK_DEPTH: 48
[ 0.000999] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000999] ... CLASSHASH_SIZE: 4096
[ 0.000999] ... MAX_LOCKDEP_ENTRIES: 8192
[ 0.000999] ... MAX_LOCKDEP_CHAINS: 16384
[ 0.000999] ... CHAINHASH_SIZE: 8192
[ 0.000999] memory used by lock dependency info: 5119 kB
[ 0.000999] per task-struct memory footprint: 2688 bytes
[ 0.000999] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000999] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000999] Checking aperture...
[ 0.000999] No AGP bridge found
[ 0.000999] Node 0: aperture @ 202a000000 size 32 MB
[ 0.000999] Aperture beyond 4GB. Ignoring.
[ 0.000999] Memory: 2016276k/2097088k available (3225k kernel code, 460k absent, 79688k reserved, 2051k data, 2180k init)
[ 0.000999] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.001012] Calibrating delay loop (skipped), value calculated using timer frequency.. 4787.99 BogoMIPS (lpj=2393995)
[ 0.003038] Security Framework initialized
[ 0.004112] Mount-cache hash table entries: 256
[ 0.007530] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.008002] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.009002] tseg: 0000000000
[ 0.010070] CPU: Physical Processor ID: 0
[ 0.011001] CPU: Processor Core ID: 0
[ 0.012010] using C1E aware idle routine
[ 0.013031] ACPI: Core revision 20090320
[ 0.022005] ftrace: converting mcount calls to 0f 1f 44 00 00
[ 0.023002] ftrace: allocating 13675 entries in 54 pages
[ 0.025212] Setting APIC routing to flat
[ 0.026741] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.037023] CPU0: Dual-Core AMD Opteron(tm) Processor 1216 stepping 02
[ 0.040993] lockdep: fixing up alternatives.
[ 0.041182] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.000999] Initializing CPU#1
[ 0.000999] Calibrating delay using timer specific routine.. 4791.25 BogoMIPS (lpj=2395625)
[ 0.000999] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.000999] CPU: L2 Cache: 1024K (64 bytes/line)
[ 0.000999] CPU: Physical Processor ID: 0
[ 0.000999] CPU: Processor Core ID: 1
[ 0.114121] CPU1: Dual-Core AMD Opteron(tm) Processor 1216 stepping 02
[ 0.117018] Brought up 2 CPUs
[ 0.117985] Total of 2 processors activated (9579.24 BogoMIPS).
[ 0.120028] CPU0 attaching sched-domain:
[ 0.120984] domain 0: span 0-1 level CPU
[ 0.122983] groups: 0 1
[ 0.124554] CPU1 attaching sched-domain:
[ 0.124984] domain 0: span 0-1 level CPU
[ 0.126982] groups: 1 0
[ 0.130206] net_namespace: 784 bytes
[ 0.131536] NET: Registered protocol family 16
[ 0.133093] node 0 link 0: io port [1000, ffffff]
[ 0.133984] TOM: 0000000080000000 aka 2048M
[ 0.134993] node 0 link 0: mmio [a0000, bffff]
[ 0.136165] node 0 link 0: mmio [80000000, ff70ffff]
[ 0.137165] bus: [00,ff] on node 0 link 0
[ 0.137981] bus: 00 index 0 io port: [0, ffff]
[ 0.138981] bus: 00 index 1 mmio: [a0000, bffff]
[ 0.139981] bus: 00 index 2 mmio: [80000000, fcffffffff]
[ 0.141025] ACPI: bus type pci registered
[ 0.142047] PCI: Using configuration type 1 for base access
[ 0.151063] bio: create slab <bio-0> at 0
[ 0.154745] ACPI: EC: Look up EC in DSDT
[ 0.169950] ACPI: Interpreter enabled
[ 0.169978] ACPI: (supports S0 S1 S5)
[ 0.172248] ACPI: Using IOAPIC for interrupt routing
[ 0.192179] ACPI Warning (tbutils-0246): Incorrect checksum in table [OEMB] - 8D, should be 82 [20090320]
[ 0.195298] ACPI: No dock devices found.
[ 0.196053] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.197128] pci 0000:00:01.0: Enabling HT MSI Mapping
[ 0.198136] pci 0000:00:02.1: reg 10 io port: [0x1f0-0x1f7]
[ 0.198983] pci 0000:00:02.1: reg 14 io port: [0x3f4-0x3f7]
[ 0.199977] pci 0000:00:02.1: reg 18 io port: [0x170-0x177]
[ 0.200977] pci 0000:00:02.1: reg 1c io port: [0x374-0x377]
[ 0.201977] pci 0000:00:02.1: reg 20 io port: [0xffa0-0xffaf]
[ 0.203108] pci 0000:00:03.0: reg 10 32bit mmio: [0xff6b4000-0xff6b4fff]
[ 0.203977] pci 0000:00:03.0: reg 14 io port: [0xe000-0xe0ff]
[ 0.205976] pci 0000:00:03.1: reg 10 32bit mmio: [0xff6b5000-0xff6b5fff]
[ 0.206977] pci 0000:00:03.1: reg 14 io port: [0xe400-0xe4ff]
[ 0.208065] pci 0000:00:03.2: reg 10 32bit mmio: [0xff6b6000-0xff6b6fff]
[ 0.208977] pci 0000:00:03.2: reg 14 io port: [0xe800-0xe8ff]
[ 0.210022] pci 0000:00:03.2: supports D1 D2
[ 0.210970] pci 0000:00:03.2: PME# supported from D0 D1 D2 D3hot
[ 0.211973] pci 0000:00:03.2: PME# disabled
[ 0.213034] pci 0000:00:04.0: reg 10 32bit mmio: [0xff680000-0xff69ffff]
[ 0.213976] pci 0000:00:04.0: reg 14 32bit mmio: [0xff660000-0xff67ffff]
[ 0.214976] pci 0000:00:04.0: reg 18 io port: [0xdc00-0xdc3f]
[ 0.215993] pci 0000:00:04.0: reg 30 32bit mmio: [0xff640000-0xff65ffff]
[ 0.216996] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
[ 0.217972] pci 0000:00:04.0: PME# disabled
[ 0.219023] pci 0000:00:05.0: reg 10 32bit mmio: [0xff620000-0xff63ffff]
[ 0.219975] pci 0000:00:05.0: reg 14 32bit mmio: [0xff600000-0xff61ffff]
[ 0.220974] pci 0000:00:05.0: reg 18 io port: [0xd880-0xd8bf]
[ 0.221992] pci 0000:00:05.0: reg 30 32bit mmio: [0xff5e0000-0xff5fffff]
[ 0.222996] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
[ 0.223971] pci 0000:00:05.0: PME# disabled
[ 0.225012] pci 0000:00:06.0: reg 10 32bit mmio: [0xf8000000-0xfbffffff]
[ 0.225974] pci 0000:00:06.0: reg 14 32bit mmio: [0xff6c0000-0xff6fffff]
[ 0.226973] pci 0000:00:06.0: reg 18 io port: [0xec00-0xec7f]
[ 0.229001] pci 0000:00:06.0: supports D1 D2
[ 0.230339] pci 0000:01:0e.0: reg 10 io port: [0xc080-0xc087]
[ 0.230971] pci 0000:01:0e.0: reg 14 io port: [0xc000-0xc003]
[ 0.231971] pci 0000:01:0e.0: reg 18 io port: [0xbc00-0xbc07]
[ 0.232971] pci 0000:01:0e.0: reg 1c io port: [0xb880-0xb883]
[ 0.233971] pci 0000:01:0e.0: reg 20 io port: [0xb800-0xb80f]
[ 0.234971] pci 0000:01:0e.0: reg 24 32bit mmio: [0xff3fe000-0xff3fffff]
[ 0.235970] pci 0000:01:0e.0: reg 30 32bit mmio: [0xff3c0000-0xff3dffff]
[ 0.237031] pci 0000:01:0e.1: reg 10 io port: [0xcc00-0xcc07]
[ 0.237970] pci 0000:01:0e.1: reg 14 io port: [0xc880-0xc883]
[ 0.238970] pci 0000:01:0e.1: reg 18 io port: [0xc800-0xc807]
[ 0.239970] pci 0000:01:0e.1: reg 1c io port: [0xc480-0xc483]
[ 0.240969] pci 0000:01:0e.1: reg 20 io port: [0xc400-0xc40f]
[ 0.242057] pci 0000:00:01.0: bridge io port: [0xb000-0xcfff]
[ 0.242967] pci 0000:00:01.0: bridge 32bit mmio: [0xff300000-0xff3fffff]
[ 0.244072] pci_bus 0000:00: on NUMA node 0
[ 0.244971] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.246176] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.247020] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1.P1P2._PRT]
[ 0.259175] ACPI: PCI Interrupt Link [LN00] (IRQs 3 4 5 7 9 11 12 14 15) *0, disabled.
[ 0.263312] ACPI: PCI Interrupt Link [LN01] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.268128] ACPI: PCI Interrupt Link [LN02] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.273308] ACPI: PCI Interrupt Link [LN03] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.278310] ACPI: PCI Interrupt Link [LN04] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.283307] ACPI: PCI Interrupt Link [LN05] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.288101] ACPI: PCI Interrupt Link [LN06] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.293306] ACPI: PCI Interrupt Link [LN07] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.298123] ACPI: PCI Interrupt Link [LN08] (IRQs 1 3 4 5 6 7 *9 11 12 14 15)
[ 0.302401] ACPI: PCI Interrupt Link [LN09] (IRQs 1 3 4 *5 6 7 9 11 12 14 15)
[ 0.306083] ACPI: PCI Interrupt Link [LN10] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.311304] ACPI: PCI Interrupt Link [LN11] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.316141] ACPI: PCI Interrupt Link [LN12] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.321350] ACPI: PCI Interrupt Link [LN13] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.327046] ACPI: PCI Interrupt Link [LN14] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.332351] ACPI: PCI Interrupt Link [LN15] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.337171] ACPI: PCI Interrupt Link [LN16] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.342350] ACPI: PCI Interrupt Link [LN17] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.347169] ACPI: PCI Interrupt Link [LN18] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.352351] ACPI: PCI Interrupt Link [LN19] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.357351] ACPI: PCI Interrupt Link [LN20] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.362352] ACPI: PCI Interrupt Link [LN21] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.367172] ACPI: PCI Interrupt Link [LN22] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.372351] ACPI: PCI Interrupt Link [LN23] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.377352] ACPI: PCI Interrupt Link [LN24] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.382352] ACPI: PCI Interrupt Link [LN25] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.387350] ACPI: PCI Interrupt Link [LN26] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.392129] ACPI: PCI Interrupt Link [LN27] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.398168] ACPI: PCI Interrupt Link [LN28] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.403352] ACPI: PCI Interrupt Link [LN29] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.408351] ACPI: PCI Interrupt Link [LN30] (IRQs 1 3 4 5 6 7 9 11 12 14 15) *0, disabled.
[ 0.414039] ACPI: PCI Interrupt Link [LNUS] (IRQs *10)
[ 0.416360] ACPI: PCI Interrupt Link [LNSA] (IRQs *11)
[ 0.419075] SCSI subsystem initialized
[ 0.421058] libata version 3.00 loaded.
[ 0.423077] usbcore: registered new interface driver usbfs
[ 0.424055] usbcore: registered new interface driver hub
[ 0.425038] usbcore: registered new device driver usb
[ 0.426115] PCI: Using ACPI for IRQ routing
[ 0.436018] pnp: PnP ACPI init
[ 0.437034] ACPI: bus type pnp registered
[ 0.445279] pnp: PnP ACPI: found 12 devices
[ 0.446003] ACPI: ACPI bus type pnp unregistered
[ 0.447021] system 00:08: ioport range 0x800-0x87f has been reserved
[ 0.448003] system 00:08: ioport range 0xa80-0xa8f has been reserved
[ 0.449012] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
[ 0.450003] system 00:09: ioport range 0xc00-0xc01 has been reserved
[ 0.451003] system 00:09: ioport range 0xcd6-0xcd7 has been reserved
[ 0.452006] system 00:09: ioport range 0xcd4-0xcd5 has been reserved
[ 0.453003] system 00:09: ioport range 0xcd8-0xcdf has been reserved
[ 0.454003] system 00:09: ioport range 0x40b-0x40b has been reserved
[ 0.455003] system 00:09: ioport range 0x4d6-0x4d6 has been reserved
[ 0.456003] system 00:09: ioport range 0xc06-0xc07 has been reserved
[ 0.457003] system 00:09: ioport range 0xc14-0xc14 has been reserved
[ 0.458003] system 00:09: ioport range 0xc49-0xc49 has been reserved
[ 0.459003] system 00:09: ioport range 0xc4a-0xc4a has been reserved
[ 0.460003] system 00:09: ioport range 0xc50-0xc51 has been reserved
[ 0.461003] system 00:09: ioport range 0xc52-0xc52 has been reserved
[ 0.462003] system 00:09: ioport range 0xc6c-0xc6c has been reserved
[ 0.463003] system 00:09: ioport range 0xc6f-0xc6f has been reserved
[ 0.465003] system 00:09: ioport range 0x500-0x57f has been reserved
[ 0.466012] system 00:0a: ioport range 0x580-0x58f has been reserved
[ 0.467003] system 00:0a: ioport range 0x590-0x593 has been reserved
[ 0.468003] system 00:0a: ioport range 0x700-0x703 has been reserved
[ 0.469003] system 00:0a: ioport range 0xca0-0xcaf has been reserved
[ 0.470004] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.471003] system 00:0a: iomem range 0xfec01000-0xfec01fff has been reserved
[ 0.472003] system 00:0a: iomem range 0xfec02000-0xfec02fff has been reserved
[ 0.473003] system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.474003] system 00:0a: iomem range 0xfff00000-0xffffffff has been reserved
[ 0.475003] system 00:0a: iomem range 0xff780000-0xffbfffff has been reserved
[ 0.476003] system 00:0a: iomem range 0xfebfe000-0xfebfefff has been reserved
[ 0.477012] system 00:0b: iomem range 0x0-0x9ffff could not be reserved
[ 0.478003] system 00:0b: iomem range 0xe0000-0xfffff could not be reserved
[ 0.479004] system 00:0b: iomem range 0x100000-0x7fffffff could not be reserved
[ 0.486501] pci 0000:01:0d.0: PCI bridge, secondary bus 0000:02
[ 0.487022] Switched to high resolution mode on CPU 0
[ 0.487213] Switched to high resolution mode on CPU 1
[ 0.497094] pci 0000:01:0d.0: IO window: disabled
[ 0.501967] pci 0000:01:0d.0: MEM window: disabled
[ 0.506925] pci 0000:01:0d.0: PREFETCH window: disabled
[ 0.512316] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.518227] pci 0000:00:01.0: IO window: 0xb000-0xcfff
[ 0.523531] pci 0000:00:01.0: MEM window: 0xff300000-0xff3fffff
[ 0.529613] pci 0000:00:01.0: PREFETCH window: disabled
[ 0.535026] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.540500] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.547360] pci_bus 0000:01: resource 0 io: [0xb000-0xcfff]
[ 0.553601] pci_bus 0000:01: resource 1 mem: [0xff300000-0xff3fffff]
[ 0.559941] pci_bus 0000:01: resource 2 mem: [0x0-0x0]
[ 0.565069] pci_bus 0000:01: resource 3 mem: [0x0-0x0]
[ 0.570199] pci_bus 0000:02: resource 0 mem: [0x0-0x0]
[ 0.575327] pci_bus 0000:02: resource 1 mem: [0x0-0x0]
[ 0.580454] pci_bus 0000:02: resource 2 mem: [0x0-0x0]
[ 0.585581] pci_bus 0000:02: resource 3 mem: [0x0-0x0]
[ 0.590794] NET: Registered protocol family 2
[ 0.607200] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.616062] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.625753] TCP bind hash table entries: 32768 (order: 9, 2359296 bytes)
[ 0.636466] TCP: Hash tables configured (established 262144 bind 32768)
[ 0.643108] TCP reno registered
[ 0.649199] NET: Registered protocol family 1
[ 0.653870] checking if image is initramfs...
[ 0.740649] rootfs image is initramfs; unpacking...
[ 0.745594] Freeing initrd memory: 2668k freed
[ 0.755727] audit: initializing netlink socket (disabled)
[ 0.761216] type=2000 audit(1242654497.761:1): initialized
[ 0.769272] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.783215] VFS: Disk quotas dquot_6.5.2
[ 0.787383] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.795622] msgmni has been set to 3944
[ 0.800880] alg: No test for stdrng (krng)
[ 0.805667] io scheduler noop registered
[ 0.809591] io scheduler anticipatory registered
[ 0.814202] io scheduler deadline registered
[ 0.818482] io scheduler cfq registered (default)
[ 0.823242] disabled boot interrupts on PCI device0x1166:0x0205
[ 0.871059] pci 0000:00:06.0: Boot video device
[ 0.876105] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.882441] processor ACPI_CPU:00: registered as cooling_device0
[ 0.888596] processor ACPI_CPU:01: registered as cooling_device1
[ 0.907665] Non-volatile memory driver v1.3
[ 0.911908] Linux agpgart interface v0.103
[ 0.916348] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
�[ 1.167644] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.418642] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.425803] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.431735] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.441852] brd: module loaded
[ 1.445211] Driver 'sd' needs updating - please use bus_type methods
[ 1.451839] sata_svw 0000:01:0e.0: version 2.3
[ 1.456333] sata_svw 0000:01:0e.0: PCI INT A -> GSI 11 (level, low) -> IRQ 11
[ 1.463639] scsi0 : sata_svw
[ 1.466949] scsi1 : sata_svw
[ 1.470022] scsi2 : sata_svw
[ 1.473090] scsi3 : sata_svw
[ 1.476112] ata1: SATA max UDMA/133 mmio m8192@0xff3fe000 port 0xff3fe000 irq 11
[ 1.483490] ata2: SATA max UDMA/133 mmio m8192@0xff3fe000 port 0xff3fe100 irq 11
[ 1.490870] ata3: SATA max UDMA/133 mmio m8192@0xff3fe000 port 0xff3fe200 irq 11
[ 1.498247] ata4: SATA max UDMA/133 mmio m8192@0xff3fe000 port 0xff3fe300 irq 11
[ 1.505712] sata_svw 0000:01:0e.1: PCI INT A -> GSI 11 (level, low) -> IRQ 11
[ 1.513536] scsi4 : pata_serverworks
[ 1.517323] scsi5 : pata_serverworks
[ 1.521046] ata5: PATA max UDMA/66 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 1.527921] ata6: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 1.535032] Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI
[ 1.541460] Copyright (c) 1999-2006 Intel Corporation.
[ 1.546627] e1000 0000:00:04.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
[ 1.690370] ata5.00: ATAPI: TEAC DV-516G, F4S7, max UDMA/33
[ 1.699343] ata5.00: configured for UDMA/33
[ 1.834378] e1000: 0000:00:04.0: e1000_probe: (PCI:33MHz:32-bit) 00:e0:81:72:62:74
[ 1.942047] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.993659] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 2.000541] e1000 0000:00:05.0: PCI INT A -> GSI 25 (level, low) -> IRQ 25
[ 2.271681] e1000: 0000:00:05.0: e1000_probe: (PCI:33MHz:32-bit) 00:e0:81:72:62:75
[ 2.443651] e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 2.450618] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.4-k4
[ 2.456700] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[ 2.462659] console [netcon0] enabled
[ 2.466320] netconsole: network logging started
[ 2.471178] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.477720] ehci_hcd 0000:00:03.2: PCI INT A -> GSI 10 (level, low) -> IRQ 10
[ 2.484849] ehci_hcd 0000:00:03.2: EHCI Host Controller
[ 2.492188] ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
[ 2.520055] ehci_hcd 0000:00:03.2: irq 10, io mem 0xff6b6000
[ 2.531045] ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00
[ 2.537344] usb usb1: configuration #1 chosen from 1 choice
[ 2.543264] hub 1-0:1.0: USB hub found
[ 2.547074] hub 1-0:1.0: 4 ports detected
[ 2.552549] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.558741] ohci_hcd 0000:00:03.0: PCI INT A -> GSI 10 (level, low) -> IRQ 10
[ 2.565869] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 2.571347] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[ 2.578745] ohci_hcd 0000:00:03.0: irq 10, io mem 0xff6b4000
[ 2.639319] usb usb2: configuration #1 chosen from 1 choice
[ 2.645015] hub 2-0:1.0: USB hub found
[ 2.648770] hub 2-0:1.0: 2 ports detected
[ 2.653366] ohci_hcd 0000:00:03.1: PCI INT A -> GSI 10 (level, low) -> IRQ 10
[ 2.660493] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 2.665985] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[ 2.673382] ohci_hcd 0000:00:03.1: irq 10, io mem 0xff6b5000
[ 2.734284] usb usb3: configuration #1 chosen from 1 choice
[ 2.740006] hub 3-0:1.0: USB hub found
[ 2.743765] hub 3-0:1.0: 2 ports detected
[ 2.748320] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.755360] usbcore: registered new interface driver libusual
[ 2.761511] PNP: No PS/2 controller found. Probing ports directly.
[ 2.769409] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.774412] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.779871] mice: PS/2 mouse device common for all mice
[ 2.785770] cpuidle: using governor ladder
[ 2.789861] cpuidle: using governor menu
[ 2.796101] usbcore: registered new interface driver hiddev
[ 2.801783] usbcore: registered new interface driver usbhid
[ 2.807346] usbhid: v2.6:USB HID core driver
[ 2.812502] TCP bic registered
[ 2.815553] NET: Registered protocol family 17
[ 2.820302] powernow-k8: Found 1 Dual-Core AMD Opteron(tm) Processor 1216 processors (2 cpu cores) (version 2.20.00)
[ 2.831228] powernow-k8: 0 : fid 0x10 (2400 MHz), vid 0xa
[ 2.836892] powernow-k8: 1 : fid 0xe (2200 MHz), vid 0xc
[ 2.842454] powernow-k8: 2 : fid 0xc (2000 MHz), vid 0xe
[ 2.848015] powernow-k8: 3 : fid 0xa (1800 MHz), vid 0x10
[ 2.853661] powernow-k8: 4 : fid 0x2 (1000 MHz), vid 0x12
[ 2.860635] registered taskstats version 1
[ 6.951257] ata1.00: qc timeout (cmd 0x27)
[ 6.955354] ata1.00: failed to read native max address (err_mask=0x4)
[ 6.961781] ata1.00: HPA support seems broken, skipping HPA handling
[ 7.273044] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 7.285159] ata1.00: configured for UDMA/133
[ 7.290052] scsi 0:0:0:0: Direct-Access ATA WDC WD1200JS-00N 10.0 PQ: 0 ANSI: 5
[ 7.299294] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
[ 7.306968] sd 0:0:0:0: [sda] Write Protect is off
[ 7.311754] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 7.316839] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.326312] sda:<6>ata2: SATA link down (SStatus 4 SControl 300)
[ 7.938372] ata3: SATA link down (SStatus 4 SControl 300)
[ 8.258372] ata4: SATA link down (SStatus 4 SControl 300)
[ 8.264357] scsi 4:0:0:0: CD-ROM TEAC DV-516G F4S7 PQ: 0 ANSI: 5
[ 37.704234] ata1: lost interrupt (Status 0x50)
[ 37.708695] sd 0:0:0:0: [sda] Unhandled error code
[ 37.713479] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_TIMEOUT
[ 37.720791] end_request: I/O error, dev sda, sector 0
[ 37.725848] Buffer I/O error on device sda, logical block 0
next prev parent reply other threads:[~2009-05-18 15:12 UTC|newest]
Thread overview: 102+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-05-09 6:45 [PATCH 1/3] x86: remove MEMORY_HOTPLUG_RESERVE related code Yinghai Lu
2009-05-09 6:48 ` [PATCH 2/3] x86: add numa_move_cpus_to_node Yinghai Lu
2009-05-09 7:05 ` Justin P. Mattock
2009-05-12 1:27 ` Christoph Lameter
2009-05-11 21:53 ` Yinghai Lu
2009-05-12 20:59 ` Christoph Lameter
2009-05-12 17:16 ` Yinghai Lu
2009-05-12 21:21 ` Christoph Lameter
2009-05-13 5:39 ` Yinghai Lu
2009-05-14 19:34 ` Christoph Lameter
2009-05-14 20:58 ` Yinghai Lu
2009-05-09 6:50 ` [PATCH 3/3] x86: fix node_possible_map logic -v2 Yinghai Lu
2009-05-11 17:53 ` Jack Steiner
2009-05-11 19:15 ` Yinghai Lu
2009-05-11 19:36 ` Yinghai Lu
2009-05-11 19:27 ` David Rientjes
2009-05-11 21:12 ` H. Peter Anvin
2009-05-11 21:26 ` Alan Cox
2009-05-11 22:25 ` David Rientjes
2009-05-12 15:06 ` Jack Steiner
2009-05-12 15:10 ` Yinghai Lu
2009-05-12 16:16 ` Jack Steiner
2009-05-12 16:40 ` Yinghai Lu
2009-05-12 18:03 ` Jack Steiner
2009-05-12 21:31 ` Yinghai Lu
2009-05-12 21:58 ` Jack Steiner
2009-05-12 23:13 ` Yinghai Lu
2009-05-12 23:26 ` Yinghai Lu
2009-05-12 15:43 ` Andi Kleen
2009-05-13 1:34 ` [PATCH] x86: fix system without memory on node0 Yinghai Lu
2009-05-13 8:00 ` Andi Kleen
2009-05-13 15:58 ` Yinghai Lu
2009-05-13 13:35 ` Ingo Molnar
2009-05-13 16:52 ` Jack Steiner
2009-05-13 17:43 ` Yinghai Lu
2009-05-13 18:08 ` Yinghai Lu
2009-05-12 7:15 ` [PATCH 3/3] x86: fix node_possible_map logic -v2 Andi Kleen
2009-05-11 21:33 ` Jack Steiner
2009-05-11 22:56 ` David Rientjes
2009-05-11 23:00 ` Yinghai Lu
2009-05-12 7:09 ` Andi Kleen
2009-05-12 1:02 ` [PATCH 1/3] x86: remove MEMORY_HOTPLUG_RESERVE related code Christoph Lameter
2009-05-12 11:16 ` Mel Gorman
2009-05-13 5:29 ` Yinghai Lu
2009-05-13 9:55 ` Mel Gorman
2009-05-13 6:13 ` [PATCH] x86: remove MEMORY_HOTPLUG_RESERVE related code -v2 Yinghai Lu
2009-05-13 14:59 ` Mel Gorman
2009-05-14 16:38 ` [PATCH 1/5] " Yinghai Lu
2009-05-14 16:40 ` [PATCH 2/5] x86: add numa_move_cpus_to_node Yinghai Lu
2009-05-14 16:41 ` [PATCH 3/5] x86: fix node_possible_map logic -v2 Yinghai Lu
2009-05-18 7:40 ` [tip:x86/mm] x86, mm: Fix node_possible_map logic tip-bot for Yinghai Lu
2009-05-14 16:42 ` [PATCH 4/5] x86: fix system without memory on node0 -v2 Yinghai Lu
2009-05-18 7:40 ` [tip:x86/mm] x86: fix system without memory on node0 tip-bot for Yinghai Lu
2009-05-14 16:43 ` [PATCH 5/5] mm: clear N_HIGH_MEMORY map before se set it again -v2 Yinghai Lu
2009-05-14 16:54 ` Andrew Morton
2009-05-14 17:05 ` Yinghai Lu
2009-05-14 17:25 ` Andrew Morton
2009-05-14 17:34 ` Yinghai Lu
2009-05-14 19:44 ` Christoph Lameter
2009-06-04 5:16 ` [RESEND PATCH] " Yinghai Lu
2009-06-04 16:38 ` Christoph Lameter
2009-06-04 16:48 ` Yinghai Lu
2009-06-04 17:11 ` Christoph Lameter
2009-06-04 17:26 ` [PATCH] mm: clear N_HIGH_MEMORY map before se set it again -v4 Yinghai Lu
2009-06-19 6:42 ` Nathan Lynch
[not found] ` <m3bpokiv0u.fsf-e+AXbWqSrlAAvxtiuMwx3w@public.gmane.org>
2009-06-19 8:18 ` Yinghai Lu
2009-06-19 8:18 ` Yinghai Lu
2009-06-19 8:43 ` Nathan Lynch
2009-06-19 16:16 ` Yinghai Lu
[not found] ` <m3prd0havh.fsf-e+AXbWqSrlAAvxtiuMwx3w@public.gmane.org>
2009-06-19 16:16 ` Yinghai Lu
2009-06-20 23:43 ` Yinghai Lu
2009-06-20 23:43 ` Yinghai Lu
2009-06-22 4:39 ` Nathan Lynch
[not found] ` <m3my807ug3.fsf-e+AXbWqSrlAAvxtiuMwx3w@public.gmane.org>
2009-06-22 15:38 ` [PATCH] x86: only clear node_states for 64bit Yinghai Lu
2009-06-22 15:38 ` Yinghai Lu
[not found] ` <4A3FA58A.3010909-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
2009-06-26 20:54 ` Andrew Morton
2009-06-26 20:54 ` Andrew Morton
2009-06-26 21:09 ` Yinghai Lu
[not found] ` <4A4538FE.2090101-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
2009-06-27 17:17 ` Ingo Molnar
2009-06-27 17:17 ` Ingo Molnar
[not found] ` <20090627171714.GD21595-X9Un+BFzKDI@public.gmane.org>
2009-06-27 20:40 ` Yinghai Lu
2009-06-27 20:40 ` Yinghai Lu
[not found] ` <4A4683B2.106-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
2009-06-29 7:39 ` Yinghai Lu
2009-06-29 7:39 ` Yinghai Lu
[not found] ` <20090626135428.d8f88a70.akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org>
2009-06-26 21:09 ` Yinghai Lu
[not found] ` <4A3D7419.8040305-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
2009-06-22 4:39 ` [PATCH] mm: clear N_HIGH_MEMORY map before se set it again -v4 Nathan Lynch
[not found] ` <4A3B49BA.40100-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
2009-06-19 8:43 ` Nathan Lynch
[not found] ` <4A2803D1.4070001-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
2009-06-19 6:42 ` Nathan Lynch
2009-05-18 7:39 ` [tip:x86/mm] mm, x86: remove MEMORY_HOTPLUG_RESERVE related code tip-bot for Yinghai Lu
[not found] ` <20090511095022.GA23121@elte.hu>
[not found] ` <20090511163158.c4e4d334.akpm@linux-foundation.org>
[not found] ` <20090512090704.GC18004@elte.hu>
[not found] ` <4A0A6700.3070100@kernel.org>
[not found] ` <20090513133635.GB7384@elte.hu>
[not found] ` <4A0AFA6E.5050200@kernel.org>
[not found] ` <20090515173521.GA29647@elte.hu>
2009-05-15 21:38 ` tip: patches in git for irq and numa Yinghai Lu
2009-05-18 7:29 ` Ingo Molnar
2009-05-18 13:50 ` Peter Zijlstra
2009-05-18 13:56 ` Ingo Molnar
2009-05-18 15:03 ` Yinghai Lu
2009-05-18 15:09 ` Ingo Molnar
2009-05-18 15:11 ` Peter Zijlstra [this message]
2009-05-18 17:23 ` Yinghai Lu
2009-05-19 9:37 ` Ingo Molnar
2009-05-19 10:31 ` Peter Zijlstra
2009-05-19 12:26 ` Ingo Molnar
2009-05-19 9:39 ` [tip:irq/numa] x86, io-apic: Don't mark pin_programmed early tip-bot for Yinghai Lu
2009-05-19 12:30 ` tip-bot for Yinghai Lu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1242659477.26820.433.camel@twins \
--to=peterz@infradead.org \
--cc=hpa@zytor.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mingo@elte.hu \
--cc=steiner@sgi.com \
--cc=tglx@linutronix.de \
--cc=yinghai@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.