All of lore.kernel.org
 help / color / mirror / Atom feed
* smsc911x IRQ on MMC1_DAT7 pin problem with ES3.1 35x
@ 2009-08-11 17:28 Peter Barada
  0 siblings, 0 replies; only message in thread
From: Peter Barada @ 2009-08-11 17:28 UTC (permalink / raw)
  To: linux-omap

I have a board that has the smsx911x driver IRQ hooked up to
R25_MMC1_DAT7, and I've setup the pin (mux offset 0x156) as "
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT", and a gpio input.

The smsc911x platform data is:

static struct smsc911x_platform_config ldp_smsc911x_platform_data = {
	.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
	.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
	.flags = SMSC911X_USE_16BIT,
	.phy_interface = PHY_INTERFACE_MODE_MII,
};

and the IRQ pin from the LAN9211 is hooked up to SD1_MMC7 and pulled to
1.8V via a 4.75Kohm resistor.

Unfortunately with ES3.1 silicon I'm getting:

OMAP-Torpedo# modprobe smsc911x
smsc911x: Driver version 2008-10-21.
irq 289: nobody cared (try booting with the "irqpoll" option)
[<c0036e40>] (dump_stack+0x0/0x14) from [<c008500c>] (__report_bad_irq
+0x3c/0x94)
[<c0084fd0>] (__report_bad_irq+0x0/0x94) from [<c00851b8>]
(note_interrupt+0x154/0x1cc)
 r4:c0406f14
[<c0085064>] (note_interrupt+0x0/0x1cc) from [<c0085f4c>]
(handle_level_irq+0xb4/0xec)
[<c0085e98>] (handle_level_irq+0x0/0xec) from [<c0048f74>]
(gpio_irq_handler+0x13c/0x180)
 r5:c0406f14 r4:00000121
[<c0048e38>] (gpio_irq_handler+0x0/0x180) from [<c0032068>]
(__exception_text_start+0x68/0x8c)
[<c0032000>] (__exception_text_start+0x0/0x8c) from [<c00329d0>]
(__irq_svc+0x30/0x80)
Exception stack(0xc7817c60 to 0xc7817ca8)
7c60: 00000000 0000033d 00000001 00000000 c0406f14 40000013 c7a26720
00000121
7c80: c0406f2c c78a8800 00000088 c7817ccc d9056000 c7817ca8 00000002
c0084974
7ca0: 40000013 ffffffff
 r5:d8200000 r4:ffffffff
[<c0084800>] (__setup_irq+0x0/0x1e0) from [<c0084a8c>] (request_irq
+0xac/0xd8)
 r8:c01e7a60 r7:c0406f14 r6:00000000 r5:00000121 r4:c7a26720
[<c00849e0>] (request_irq+0x0/0xd8) from [<c030719c>]
(smsc911x_drv_probe+0x5bc/0x12f8)
[<c0306be0>] (smsc911x_drv_probe+0x0/0x12f8) from [<c01db38c>]
(platform_drv_probe+0x20/0x24)
[<c01db36c>] (platform_drv_probe+0x0/0x24) from [<c01da540>]
(driver_probe_device+0xec/0x198)
[<c01da454>] (driver_probe_device+0x0/0x198) from [<c01da658>]
(__driver_attach+0x6c/0x90)
 r6:c03ff6dc r5:c04183b4 r4:c03ff630
[<c01da5ec>] (__driver_attach+0x0/0x90) from [<c01d9a7c>]
(bus_for_each_dev+0x4c/0x84)
 r6:c01da5ec r5:c7817db0 r4:00000000
[<c01d9a30>] (bus_for_each_dev+0x0/0x84) from [<c01da368>]
(driver_attach+0x20/0x28)
 r7:00000000 r6:c78c8b40 r5:c04183b4 r4:00000000
[<c01da348>] (driver_attach+0x0/0x28) from [<c01d9f18>] (bus_add_driver
+0xa8/0x218)
[<c01d9e70>] (bus_add_driver+0x0/0x218) from [<c01da85c>]
(driver_register+0x98/0x11c)
[<c01da7c4>] (driver_register+0x0/0x11c) from [<c01db728>]
(platform_driver_register+0x78/0x94)
[<c01db6b0>] (platform_driver_register+0x0/0x94) from [<c001ebb0>]
(smsc911x_init_module+0x14/0x1c)
[<c001eb9c>] (smsc911x_init_module+0x0/0x1c) from [<c00322d8>]
(__exception_text_end+0x60/0x190)
[<c0032278>] (__exception_text_end+0x0/0x190) from [<c0008730>]
(kernel_init+0x6c/0xd8)
[<c00086c4>] (kernel_init+0x0/0xd8) from [<c0060d90>] (do_exit
+0x0/0x6e0)
 r5:00000000 r4:00000000
handlers:
[<c01e7a60>] (smsc911x_irqhandler+0x0/0x558)
Disabling IRQ #289


0) Looking at the IRQ pin with a scope while modprobing the driver shows
it steady at 1.8V.

1) Do I need (and how?) to setup PBIAS and/or VMMC1 to make the
MMC1_DAT4 through MMC1_DAT7 usable as GPIO pins at 1.8V while allowing
MMC1_DAT0 through MMC1_DAT3 to be used for an SD/MMC port?

2) Will the code in twl_mmc1_set_power() affect the voltage/bias on pins
MMC1_dat4 through MMC1_DAT7?

-- 
Peter Barada <peterb@logicpd.com>
Logic Product Development, Inc.

^ permalink raw reply	[flat|nested] only message in thread

only message in thread, other threads:[~2009-08-11 17:24 UTC | newest]

Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-08-11 17:28 smsc911x IRQ on MMC1_DAT7 pin problem with ES3.1 35x Peter Barada

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.