* [PATCH v3] MXC: mach_armadillo5x0: Add USB Host support.
@ 2010-02-25 10:46 Alberto Panizzo
0 siblings, 0 replies; only message in thread
From: Alberto Panizzo @ 2010-02-25 10:46 UTC (permalink / raw)
To: linux-arm-kernel
This add USB Host capability. The Armadillo 500 board is supplied
with two USB Host connectors driven by the USB OTG and USB Host 2
ports, through two NXP isp 1504 transceivers.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
---
This patch is based on top of Pengutronix mxc-master branch.
Please, if possible add this for 2.6.34.
Thanks.
Alberto!
arch/arm/mach-mx3/Kconfig | 1 +
arch/arm/mach-mx3/mach-armadillo5x0.c | 131 +++++++++++++++++++++++++++++++++
2 files changed, 132 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-mx3/Kconfig b/arch/arm/mach-mx3/Kconfig
index 3872af1..96069a4 100644
--- a/arch/arm/mach-mx3/Kconfig
+++ b/arch/arm/mach-mx3/Kconfig
@@ -95,6 +95,7 @@ config MACH_PCM043
config MACH_ARMADILLO5X0
bool "Support Atmark Armadillo-500 Development Base Board"
select ARCH_MX31
+ select MXC_ULPI if USB_ULPI
help
Include support for Atmark Armadillo-500 platform. This includes
specific configurations for the board and its peripherals.
diff --git a/arch/arm/mach-mx3/mach-armadillo5x0.c b/arch/arm/mach-mx3/mach-armadillo5x0.c
index 3d72b0b..d0309fa 100644
--- a/arch/arm/mach-mx3/mach-armadillo5x0.c
+++ b/arch/arm/mach-mx3/mach-armadillo5x0.c
@@ -36,6 +36,9 @@
#include <linux/input.h>
#include <linux/gpio_keys.h>
#include <linux/i2c.h>
+#include <linux/usb/otg.h>
+#include <linux/usb/ulpi.h>
+#include <linux/delay.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -52,6 +55,8 @@
#include <mach/ipu.h>
#include <mach/mx3fb.h>
#include <mach/mxc_nand.h>
+#include <mach/mxc_ehci.h>
+#include <mach/ulpi.h>
#include "devices.h"
#include "crm_regs.h"
@@ -103,8 +108,123 @@ static int armadillo5x0_pins[] = {
/* I2C2 */
MX31_PIN_CSPI2_MOSI__SCL,
MX31_PIN_CSPI2_MISO__SDA,
+ /* OTG */
+ MX31_PIN_USBOTG_DATA0__USBOTG_DATA0,
+ MX31_PIN_USBOTG_DATA1__USBOTG_DATA1,
+ MX31_PIN_USBOTG_DATA2__USBOTG_DATA2,
+ MX31_PIN_USBOTG_DATA3__USBOTG_DATA3,
+ MX31_PIN_USBOTG_DATA4__USBOTG_DATA4,
+ MX31_PIN_USBOTG_DATA5__USBOTG_DATA5,
+ MX31_PIN_USBOTG_DATA6__USBOTG_DATA6,
+ MX31_PIN_USBOTG_DATA7__USBOTG_DATA7,
+ MX31_PIN_USBOTG_CLK__USBOTG_CLK,
+ MX31_PIN_USBOTG_DIR__USBOTG_DIR,
+ MX31_PIN_USBOTG_NXT__USBOTG_NXT,
+ MX31_PIN_USBOTG_STP__USBOTG_STP,
+ /* USB host 2 */
+ IOMUX_MODE(MX31_PIN_USBH2_CLK, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_USBH2_DIR, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_USBH2_NXT, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_USBH2_STP, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_USBH2_DATA0, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_USBH2_DATA1, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_STXD3, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_SRXD3, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_SCK3, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_SFS3, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_STXD6, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_SRXD6, IOMUX_CONFIG_FUNC),
};
+/* USB */
+#if defined(CONFIG_USB_ULPI)
+
+#define OTG_RESET IOMUX_TO_GPIO(MX31_PIN_STXD4)
+#define USBH2_RESET IOMUX_TO_GPIO(MX31_PIN_SCK6)
+#define USBH2_CS IOMUX_TO_GPIO(MX31_PIN_GPIO1_3)
+
+#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
+ PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
+
+static int usbotg_init(struct platform_device *pdev)
+{
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_STP, USB_PAD_CFG);
+
+ /* Chip already enabled by hardware */
+ /* OTG phy reset*/
+ gpio_request(OTG_RESET, "USB-OTG-RESET");
+
+ if (gpio_direction_output(OTG_RESET, 1/*HIGH*/)) {
+ pr_warning("Failed to reset usbotg phy \n");
+ return -1;
+ }
+ gpio_set_value(OTG_RESET, 0/*LOW*/);
+ mdelay(5);
+ gpio_set_value(OTG_RESET, 1/*HIGH*/);
+
+ return 0;
+}
+
+static int usbh2_init(struct platform_device *pdev)
+{
+ mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG);
+
+ mxc_iomux_set_gpr(MUX_PGP_UH2, true);
+
+
+ /* Enable the chip */
+ gpio_request(USBH2_CS, "USB-H2-CS");
+ gpio_direction_output(USBH2_CS, 0/*Enabled*/);
+
+ /* H2 phy reset*/
+ gpio_request(USBH2_RESET, "USB-H2-RESET");
+
+ if (gpio_direction_output(USBH2_RESET, 1/*HIGH*/)) {
+ pr_warning("Failed to reset usbh2 phy \n");
+ return -1;
+ }
+ gpio_set_value(USBH2_RESET, 0/*LOW*/);
+ mdelay(5);
+ gpio_set_value(USBH2_RESET, 1/*HIGH*/);
+
+ return 0;
+}
+
+static struct mxc_usbh_platform_data usbotg_pdata = {
+ .init = usbotg_init,
+ .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
+ .flags = MXC_EHCI_POWER_PINS_ENABLED | MXC_EHCI_INTERFACE_DIFF_UNI,
+};
+
+static struct mxc_usbh_platform_data usbh2_pdata = {
+ .init = usbh2_init,
+ .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
+ .flags = MXC_EHCI_POWER_PINS_ENABLED | MXC_EHCI_INTERFACE_DIFF_UNI,
+};
+#endif /* CONFIG_USB_ULPI */
+
/* RTC over I2C*/
#define ARMADILLO5X0_RTC_GPIO IOMUX_TO_GPIO(MX31_PIN_SRXD4)
@@ -393,6 +513,17 @@ static void __init armadillo5x0_init(void)
if (armadillo5x0_i2c_rtc.irq == 0)
pr_warning("armadillo5x0_init: failed to get RTC IRQ\n");
i2c_register_board_info(1, &armadillo5x0_i2c_rtc, 1);
+
+ /* USB */
+#if defined(CONFIG_USB_ULPI)
+ usbotg_pdata.otg = otg_ulpi_create(&mxc_ulpi_access_ops,
+ USB_OTG_DRV_VBUS | USB_OTG_DRV_VBUS_EXT);
+ usbh2_pdata.otg = otg_ulpi_create(&mxc_ulpi_access_ops,
+ USB_OTG_DRV_VBUS | USB_OTG_DRV_VBUS_EXT);
+
+ mxc_register_device(&mxc_otg_host, &usbotg_pdata);
+ mxc_register_device(&mxc_usbh2, &usbh2_pdata);
+#endif
}
static void __init armadillo5x0_timer_init(void)
--
1.6.3.3
^ permalink raw reply related [flat|nested] only message in thread
only message in thread, other threads:[~2010-02-25 10:46 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-02-25 10:46 [PATCH v3] MXC: mach_armadillo5x0: Add USB Host support Alberto Panizzo
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.