From: sboyd@codeaurora.org (Stephen Boyd)
To: linux-arm-kernel@lists.infradead.org
Subject: [TRIVIAL/PATCH] ARM: hw_breakpoint: Fix newlines in WARN messages
Date: Thu, 24 Feb 2011 10:55:39 -0800 [thread overview]
Message-ID: <1298573739-25144-1-git-send-email-sboyd@codeaurora.org> (raw)
These warnings are missing newlines and spaces causing confusing
looking output when they trigger.
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
arch/arm/kernel/hw_breakpoint.c | 13 +++++++------
1 files changed, 7 insertions(+), 6 deletions(-)
diff --git a/arch/arm/kernel/hw_breakpoint.c b/arch/arm/kernel/hw_breakpoint.c
index d600bd3..5aab00e 100644
--- a/arch/arm/kernel/hw_breakpoint.c
+++ b/arch/arm/kernel/hw_breakpoint.c
@@ -238,8 +238,8 @@ static int enable_monitor_mode(void)
ARM_DBG_READ(c1, 0, dscr);
/* Ensure that halting mode is disabled. */
- if (WARN_ONCE(dscr & ARM_DSCR_HDBGEN, "halting debug mode enabled."
- "Unable to access hardware resources.")) {
+ if (WARN_ONCE(dscr & ARM_DSCR_HDBGEN, "halting debug mode enabled. "
+ "Unable to access hardware resources.\n")) {
ret = -EPERM;
goto out;
}
@@ -377,7 +377,7 @@ int arch_install_hw_breakpoint(struct perf_event *bp)
}
}
- if (WARN_ONCE(i == max_slots, "Can't find any breakpoint slot")) {
+ if (WARN_ONCE(i == max_slots, "Can't find any breakpoint slot\n")) {
ret = -EBUSY;
goto out;
}
@@ -423,7 +423,7 @@ void arch_uninstall_hw_breakpoint(struct perf_event *bp)
}
}
- if (WARN_ONCE(i == max_slots, "Can't find any breakpoint slot"))
+ if (WARN_ONCE(i == max_slots, "Can't find any breakpoint slot\n"))
return;
/* Reset the control register. */
@@ -635,7 +635,7 @@ int arch_validate_hwbkpt_settings(struct perf_event *bp)
if (WARN_ONCE(!bp->overflow_handler &&
(arch_check_bp_in_kernelspace(bp) || !core_has_mismatch_brps()
|| !bp->hw.bp_target),
- "overflow handler required but none found")) {
+ "overflow handler required but none found\n")) {
ret = -EINVAL;
}
out:
@@ -917,7 +917,8 @@ static int __init arch_hw_breakpoint_init(void)
if (dscr & ARM_DSCR_HDBGEN) {
max_watchpoint_len = 4;
pr_warning("halting debug mode enabled. Assuming maximum "
- "watchpoint size of %u bytes.", max_watchpoint_len);
+ "watchpoint size of %u bytes.\n",
+ max_watchpoint_len);
} else {
/* Work out the maximum supported watchpoint length. */
max_watchpoint_len = get_max_wp_len();
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
WARNING: multiple messages have this Message-ID (diff)
From: Stephen Boyd <sboyd@codeaurora.org>
To: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org, trivial@kernel.org,
Will Deacon <will.deacon@arm.com>
Subject: [TRIVIAL/PATCH] ARM: hw_breakpoint: Fix newlines in WARN messages
Date: Thu, 24 Feb 2011 10:55:39 -0800 [thread overview]
Message-ID: <1298573739-25144-1-git-send-email-sboyd@codeaurora.org> (raw)
These warnings are missing newlines and spaces causing confusing
looking output when they trigger.
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
arch/arm/kernel/hw_breakpoint.c | 13 +++++++------
1 files changed, 7 insertions(+), 6 deletions(-)
diff --git a/arch/arm/kernel/hw_breakpoint.c b/arch/arm/kernel/hw_breakpoint.c
index d600bd3..5aab00e 100644
--- a/arch/arm/kernel/hw_breakpoint.c
+++ b/arch/arm/kernel/hw_breakpoint.c
@@ -238,8 +238,8 @@ static int enable_monitor_mode(void)
ARM_DBG_READ(c1, 0, dscr);
/* Ensure that halting mode is disabled. */
- if (WARN_ONCE(dscr & ARM_DSCR_HDBGEN, "halting debug mode enabled."
- "Unable to access hardware resources.")) {
+ if (WARN_ONCE(dscr & ARM_DSCR_HDBGEN, "halting debug mode enabled. "
+ "Unable to access hardware resources.\n")) {
ret = -EPERM;
goto out;
}
@@ -377,7 +377,7 @@ int arch_install_hw_breakpoint(struct perf_event *bp)
}
}
- if (WARN_ONCE(i == max_slots, "Can't find any breakpoint slot")) {
+ if (WARN_ONCE(i == max_slots, "Can't find any breakpoint slot\n")) {
ret = -EBUSY;
goto out;
}
@@ -423,7 +423,7 @@ void arch_uninstall_hw_breakpoint(struct perf_event *bp)
}
}
- if (WARN_ONCE(i == max_slots, "Can't find any breakpoint slot"))
+ if (WARN_ONCE(i == max_slots, "Can't find any breakpoint slot\n"))
return;
/* Reset the control register. */
@@ -635,7 +635,7 @@ int arch_validate_hwbkpt_settings(struct perf_event *bp)
if (WARN_ONCE(!bp->overflow_handler &&
(arch_check_bp_in_kernelspace(bp) || !core_has_mismatch_brps()
|| !bp->hw.bp_target),
- "overflow handler required but none found")) {
+ "overflow handler required but none found\n")) {
ret = -EINVAL;
}
out:
@@ -917,7 +917,8 @@ static int __init arch_hw_breakpoint_init(void)
if (dscr & ARM_DSCR_HDBGEN) {
max_watchpoint_len = 4;
pr_warning("halting debug mode enabled. Assuming maximum "
- "watchpoint size of %u bytes.", max_watchpoint_len);
+ "watchpoint size of %u bytes.\n",
+ max_watchpoint_len);
} else {
/* Work out the maximum supported watchpoint length. */
max_watchpoint_len = get_max_wp_len();
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
next reply other threads:[~2011-02-24 18:55 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-02-24 18:55 Stephen Boyd [this message]
2011-02-24 18:55 ` [TRIVIAL/PATCH] ARM: hw_breakpoint: Fix newlines in WARN messages Stephen Boyd
2011-02-25 6:38 ` Lothar Waßmann
2011-02-25 6:38 ` Lothar Waßmann
2011-02-25 11:31 ` Will Deacon
2011-02-25 11:31 ` Will Deacon
2011-02-26 4:06 ` [PATCH] ARM: hw_breakpoint: Fix newlines in WARNings Stephen Boyd
2011-02-26 4:06 ` Stephen Boyd
2011-03-09 19:36 ` Stephen Boyd
2011-03-09 19:36 ` Stephen Boyd
2011-03-09 21:58 ` Will Deacon
2011-03-09 21:58 ` Will Deacon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1298573739-25144-1-git-send-email-sboyd@codeaurora.org \
--to=sboyd@codeaurora.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.