From: ccross@android.com (Colin Cross)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/3] ARM: gic: Use cpu pm notifiers to save gic state
Date: Sun, 12 Jun 2011 17:43:44 -0700 [thread overview]
Message-ID: <1307925825-28566-3-git-send-email-ccross@android.com> (raw)
In-Reply-To: <1307925825-28566-1-git-send-email-ccross@android.com>
When the cpu is powered down in a low power mode, the gic cpu
interface may be reset, and when the cpu complex is powered
down, the gic distributor may also be reset.
This patch uses CPU_PM_ENTER and CPU_PM_EXIT notifiers to save
and restore the gic cpu interface registers, and the
CPU_COMPLEX_PM_ENTER and CPU_COMPLEX_PM_EXIT notifiers to save
and restore the gic distributor registers.
Signed-off-by: Colin Cross <ccross@android.com>
---
arch/arm/common/gic.c | 212 +++++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 212 insertions(+), 0 deletions(-)
diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c
index 4ddd0a6..8d62e07 100644
--- a/arch/arm/common/gic.c
+++ b/arch/arm/common/gic.c
@@ -29,6 +29,7 @@
#include <linux/cpumask.h>
#include <linux/io.h>
+#include <asm/cpu_pm.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <asm/hardware/gic.h>
@@ -42,6 +43,17 @@ struct gic_chip_data {
unsigned int irq_offset;
void __iomem *dist_base;
void __iomem *cpu_base;
+#ifdef CONFIG_CPU_PM
+ u32 saved_spi_enable[DIV_ROUND_UP(1020, 32)];
+ u32 saved_spi_conf[DIV_ROUND_UP(1020, 16)];
+ u32 saved_spi_pri[DIV_ROUND_UP(1020, 4)];
+ u32 saved_spi_target[DIV_ROUND_UP(1020, 4)];
+ u32 __percpu *saved_ppi_enable;
+ u32 __percpu *saved_ppi_conf;
+ u32 __percpu *saved_ppi_pri;
+#endif
+
+ unsigned int gic_irqs;
};
/*
@@ -283,6 +295,8 @@ static void __init gic_dist_init(struct gic_chip_data *gic,
if (gic_irqs > 1020)
gic_irqs = 1020;
+ gic->gic_irqs = gic_irqs;
+
/*
* Set all global interrupts to be level triggered, active low.
*/
@@ -350,6 +364,203 @@ static void __cpuinit gic_cpu_init(struct gic_chip_data *gic)
writel_relaxed(1, base + GIC_CPU_CTRL);
}
+#ifdef CONFIG_CPU_PM
+/*
+ * Saves the GIC distributor registers during suspend or idle. Must be called
+ * with interrupts disabled but before powering down the GIC. After calling
+ * this function, no interrupts will be delivered by the GIC, and another
+ * platform-specific wakeup source must be enabled.
+ */
+static void gic_dist_save(unsigned int gic_nr)
+{
+ unsigned int gic_irqs;
+ void __iomem *dist_base;
+ int i;
+
+ if (gic_nr >= MAX_GIC_NR)
+ BUG();
+
+ gic_irqs = gic_data[gic_nr].gic_irqs;
+ dist_base = gic_data[gic_nr].dist_base;
+
+ if (!dist_base)
+ return;
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 16); i++)
+ gic_data[gic_nr].saved_spi_conf[i] =
+ readl_relaxed(dist_base + GIC_DIST_CONFIG + i * 4);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
+ gic_data[gic_nr].saved_spi_pri[i] =
+ readl_relaxed(dist_base + GIC_DIST_PRI + i * 4);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
+ gic_data[gic_nr].saved_spi_target[i] =
+ readl_relaxed(dist_base + GIC_DIST_TARGET + i * 4);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 32); i++)
+ gic_data[gic_nr].saved_spi_enable[i] =
+ readl_relaxed(dist_base + GIC_DIST_ENABLE_SET + i * 4);
+
+ writel_relaxed(0, dist_base + GIC_DIST_CTRL);
+}
+
+/*
+ * Restores the GIC distributor registers during resume or when coming out of
+ * idle. Must be called before enabling interrupts. If a level interrupt
+ * that occured while the GIC was suspended is still present, it will be
+ * handled normally, but any edge interrupts that occured will not be seen by
+ * the GIC and need to be handled by the platform-specific wakeup source.
+ */
+static void gic_dist_restore(unsigned int gic_nr)
+{
+ unsigned int gic_irqs;
+ unsigned int i;
+ void __iomem *dist_base;
+
+ if (gic_nr >= MAX_GIC_NR)
+ BUG();
+
+ gic_irqs = gic_data[gic_nr].gic_irqs;
+ dist_base = gic_data[gic_nr].dist_base;
+
+ if (!dist_base)
+ return;
+
+ writel_relaxed(0, dist_base + GIC_DIST_CTRL);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 16); i++)
+ writel_relaxed(gic_data[gic_nr].saved_spi_conf[i],
+ dist_base + GIC_DIST_CONFIG + i * 4);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
+ writel_relaxed(gic_data[gic_nr].saved_spi_pri[i],
+ dist_base + GIC_DIST_PRI + i * 4);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
+ writel_relaxed(gic_data[gic_nr].saved_spi_target[i],
+ dist_base + GIC_DIST_TARGET + i * 4);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 32); i++)
+ writel_relaxed(gic_data[gic_nr].saved_spi_enable[i],
+ dist_base + GIC_DIST_ENABLE_SET + i * 4);
+
+ writel_relaxed(1, dist_base + GIC_DIST_CTRL);
+}
+
+static void gic_cpu_save(unsigned int gic_nr)
+{
+ int i;
+ u32 *ptr;
+ void __iomem *dist_base;
+ void __iomem *cpu_base;
+
+ if (gic_nr >= MAX_GIC_NR)
+ BUG();
+
+ dist_base = gic_data[gic_nr].dist_base;
+ cpu_base = gic_data[gic_nr].cpu_base;
+
+ if (!dist_base || !cpu_base)
+ return;
+
+ ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_enable);
+ for (i = 0; i < DIV_ROUND_UP(32, 32); i++)
+ ptr[i] = readl_relaxed(dist_base + GIC_DIST_ENABLE_SET + i * 4);
+
+ ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_conf);
+ for (i = 0; i < DIV_ROUND_UP(32, 16); i++)
+ ptr[i] = readl_relaxed(dist_base + GIC_DIST_CONFIG + i * 4);
+
+ ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_pri);
+ for (i = 0; i < DIV_ROUND_UP(32, 4); i++)
+ ptr[i] = readl_relaxed(dist_base + GIC_DIST_PRI + i * 4);
+}
+
+static void gic_cpu_restore(unsigned int gic_nr)
+{
+ int i;
+ u32 *ptr;
+ void __iomem *dist_base;
+ void __iomem *cpu_base;
+
+ if (gic_nr >= MAX_GIC_NR)
+ BUG();
+
+ dist_base = gic_data[gic_nr].dist_base;
+ cpu_base = gic_data[gic_nr].cpu_base;
+
+ if (!dist_base || !cpu_base)
+ return;
+
+ ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_enable);
+ for (i = 0; i < DIV_ROUND_UP(32, 32); i++)
+ writel_relaxed(ptr[i], dist_base + GIC_DIST_ENABLE_SET + i * 4);
+
+ ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_conf);
+ for (i = 0; i < DIV_ROUND_UP(32, 16); i++)
+ writel_relaxed(ptr[i], dist_base + GIC_DIST_CONFIG + i * 4);
+
+ ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_pri);
+ for (i = 0; i < DIV_ROUND_UP(32, 4); i++)
+ writel_relaxed(ptr[i], dist_base + GIC_DIST_PRI + i * 4);
+
+ writel_relaxed(0xf0, cpu_base + GIC_CPU_PRIMASK);
+ writel_relaxed(1, cpu_base + GIC_CPU_CTRL);
+}
+
+static int gic_notifier(struct notifier_block *self, unsigned long cmd, void *v)
+{
+ int i;
+
+ for (i = 0; i < MAX_GIC_NR; i++) {
+ switch (cmd) {
+ case CPU_PM_ENTER:
+ gic_cpu_save(i);
+ break;
+ case CPU_PM_ENTER_FAILED:
+ case CPU_PM_EXIT:
+ gic_cpu_restore(i);
+ break;
+ case CPU_COMPLEX_PM_ENTER:
+ gic_dist_save(i);
+ break;
+ case CPU_COMPLEX_PM_ENTER_FAILED:
+ case CPU_COMPLEX_PM_EXIT:
+ gic_dist_restore(i);
+ break;
+ }
+ }
+
+ return NOTIFY_OK;
+}
+
+static struct notifier_block gic_notifier_block = {
+ .notifier_call = gic_notifier,
+};
+
+static void __init gic_cpu_pm_init(struct gic_chip_data *gic)
+{
+ gic->saved_ppi_enable = __alloc_percpu(DIV_ROUND_UP(32, 32) * 4,
+ sizeof(u32));
+ BUG_ON(!gic->saved_ppi_enable);
+
+ gic->saved_ppi_conf = __alloc_percpu(DIV_ROUND_UP(32, 16) * 4,
+ sizeof(u32));
+ BUG_ON(!gic->saved_ppi_conf);
+
+ gic->saved_ppi_pri = __alloc_percpu(DIV_ROUND_UP(32, 4) * 4,
+ sizeof(u32));
+ BUG_ON(!gic->saved_ppi_pri);
+
+ cpu_pm_register_notifier(&gic_notifier_block);
+}
+#else
+static void __init gic_cpu_pm_init(struct gic_chip_data *gic)
+{
+}
+#endif
+
void __init gic_init(unsigned int gic_nr, unsigned int irq_start,
void __iomem *dist_base, void __iomem *cpu_base)
{
@@ -367,6 +578,7 @@ void __init gic_init(unsigned int gic_nr, unsigned int irq_start,
gic_dist_init(gic, irq_start);
gic_cpu_init(gic);
+ gic_cpu_pm_init(gic);
}
void __cpuinit gic_secondary_init(unsigned int gic_nr)
--
1.7.4.1
WARNING: multiple messages have this Message-ID (diff)
From: Colin Cross <ccross@android.com>
To: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org,
Russell King <linux@arm.linux.org.uk>,
Catalin Marinas <catalin.marinas@arm.com>,
Santosh Shilimkar <santosh.shilimkar@ti.com>,
Colin Cross <ccross@android.com>,
Thomas Gleixner <tglx@linutronix.de>,
Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Subject: [PATCH 2/3] ARM: gic: Use cpu pm notifiers to save gic state
Date: Sun, 12 Jun 2011 17:43:44 -0700 [thread overview]
Message-ID: <1307925825-28566-3-git-send-email-ccross@android.com> (raw)
In-Reply-To: <1307925825-28566-1-git-send-email-ccross@android.com>
When the cpu is powered down in a low power mode, the gic cpu
interface may be reset, and when the cpu complex is powered
down, the gic distributor may also be reset.
This patch uses CPU_PM_ENTER and CPU_PM_EXIT notifiers to save
and restore the gic cpu interface registers, and the
CPU_COMPLEX_PM_ENTER and CPU_COMPLEX_PM_EXIT notifiers to save
and restore the gic distributor registers.
Signed-off-by: Colin Cross <ccross@android.com>
---
arch/arm/common/gic.c | 212 +++++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 212 insertions(+), 0 deletions(-)
diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c
index 4ddd0a6..8d62e07 100644
--- a/arch/arm/common/gic.c
+++ b/arch/arm/common/gic.c
@@ -29,6 +29,7 @@
#include <linux/cpumask.h>
#include <linux/io.h>
+#include <asm/cpu_pm.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <asm/hardware/gic.h>
@@ -42,6 +43,17 @@ struct gic_chip_data {
unsigned int irq_offset;
void __iomem *dist_base;
void __iomem *cpu_base;
+#ifdef CONFIG_CPU_PM
+ u32 saved_spi_enable[DIV_ROUND_UP(1020, 32)];
+ u32 saved_spi_conf[DIV_ROUND_UP(1020, 16)];
+ u32 saved_spi_pri[DIV_ROUND_UP(1020, 4)];
+ u32 saved_spi_target[DIV_ROUND_UP(1020, 4)];
+ u32 __percpu *saved_ppi_enable;
+ u32 __percpu *saved_ppi_conf;
+ u32 __percpu *saved_ppi_pri;
+#endif
+
+ unsigned int gic_irqs;
};
/*
@@ -283,6 +295,8 @@ static void __init gic_dist_init(struct gic_chip_data *gic,
if (gic_irqs > 1020)
gic_irqs = 1020;
+ gic->gic_irqs = gic_irqs;
+
/*
* Set all global interrupts to be level triggered, active low.
*/
@@ -350,6 +364,203 @@ static void __cpuinit gic_cpu_init(struct gic_chip_data *gic)
writel_relaxed(1, base + GIC_CPU_CTRL);
}
+#ifdef CONFIG_CPU_PM
+/*
+ * Saves the GIC distributor registers during suspend or idle. Must be called
+ * with interrupts disabled but before powering down the GIC. After calling
+ * this function, no interrupts will be delivered by the GIC, and another
+ * platform-specific wakeup source must be enabled.
+ */
+static void gic_dist_save(unsigned int gic_nr)
+{
+ unsigned int gic_irqs;
+ void __iomem *dist_base;
+ int i;
+
+ if (gic_nr >= MAX_GIC_NR)
+ BUG();
+
+ gic_irqs = gic_data[gic_nr].gic_irqs;
+ dist_base = gic_data[gic_nr].dist_base;
+
+ if (!dist_base)
+ return;
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 16); i++)
+ gic_data[gic_nr].saved_spi_conf[i] =
+ readl_relaxed(dist_base + GIC_DIST_CONFIG + i * 4);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
+ gic_data[gic_nr].saved_spi_pri[i] =
+ readl_relaxed(dist_base + GIC_DIST_PRI + i * 4);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
+ gic_data[gic_nr].saved_spi_target[i] =
+ readl_relaxed(dist_base + GIC_DIST_TARGET + i * 4);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 32); i++)
+ gic_data[gic_nr].saved_spi_enable[i] =
+ readl_relaxed(dist_base + GIC_DIST_ENABLE_SET + i * 4);
+
+ writel_relaxed(0, dist_base + GIC_DIST_CTRL);
+}
+
+/*
+ * Restores the GIC distributor registers during resume or when coming out of
+ * idle. Must be called before enabling interrupts. If a level interrupt
+ * that occured while the GIC was suspended is still present, it will be
+ * handled normally, but any edge interrupts that occured will not be seen by
+ * the GIC and need to be handled by the platform-specific wakeup source.
+ */
+static void gic_dist_restore(unsigned int gic_nr)
+{
+ unsigned int gic_irqs;
+ unsigned int i;
+ void __iomem *dist_base;
+
+ if (gic_nr >= MAX_GIC_NR)
+ BUG();
+
+ gic_irqs = gic_data[gic_nr].gic_irqs;
+ dist_base = gic_data[gic_nr].dist_base;
+
+ if (!dist_base)
+ return;
+
+ writel_relaxed(0, dist_base + GIC_DIST_CTRL);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 16); i++)
+ writel_relaxed(gic_data[gic_nr].saved_spi_conf[i],
+ dist_base + GIC_DIST_CONFIG + i * 4);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
+ writel_relaxed(gic_data[gic_nr].saved_spi_pri[i],
+ dist_base + GIC_DIST_PRI + i * 4);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++)
+ writel_relaxed(gic_data[gic_nr].saved_spi_target[i],
+ dist_base + GIC_DIST_TARGET + i * 4);
+
+ for (i = 0; i < DIV_ROUND_UP(gic_irqs, 32); i++)
+ writel_relaxed(gic_data[gic_nr].saved_spi_enable[i],
+ dist_base + GIC_DIST_ENABLE_SET + i * 4);
+
+ writel_relaxed(1, dist_base + GIC_DIST_CTRL);
+}
+
+static void gic_cpu_save(unsigned int gic_nr)
+{
+ int i;
+ u32 *ptr;
+ void __iomem *dist_base;
+ void __iomem *cpu_base;
+
+ if (gic_nr >= MAX_GIC_NR)
+ BUG();
+
+ dist_base = gic_data[gic_nr].dist_base;
+ cpu_base = gic_data[gic_nr].cpu_base;
+
+ if (!dist_base || !cpu_base)
+ return;
+
+ ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_enable);
+ for (i = 0; i < DIV_ROUND_UP(32, 32); i++)
+ ptr[i] = readl_relaxed(dist_base + GIC_DIST_ENABLE_SET + i * 4);
+
+ ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_conf);
+ for (i = 0; i < DIV_ROUND_UP(32, 16); i++)
+ ptr[i] = readl_relaxed(dist_base + GIC_DIST_CONFIG + i * 4);
+
+ ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_pri);
+ for (i = 0; i < DIV_ROUND_UP(32, 4); i++)
+ ptr[i] = readl_relaxed(dist_base + GIC_DIST_PRI + i * 4);
+}
+
+static void gic_cpu_restore(unsigned int gic_nr)
+{
+ int i;
+ u32 *ptr;
+ void __iomem *dist_base;
+ void __iomem *cpu_base;
+
+ if (gic_nr >= MAX_GIC_NR)
+ BUG();
+
+ dist_base = gic_data[gic_nr].dist_base;
+ cpu_base = gic_data[gic_nr].cpu_base;
+
+ if (!dist_base || !cpu_base)
+ return;
+
+ ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_enable);
+ for (i = 0; i < DIV_ROUND_UP(32, 32); i++)
+ writel_relaxed(ptr[i], dist_base + GIC_DIST_ENABLE_SET + i * 4);
+
+ ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_conf);
+ for (i = 0; i < DIV_ROUND_UP(32, 16); i++)
+ writel_relaxed(ptr[i], dist_base + GIC_DIST_CONFIG + i * 4);
+
+ ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_pri);
+ for (i = 0; i < DIV_ROUND_UP(32, 4); i++)
+ writel_relaxed(ptr[i], dist_base + GIC_DIST_PRI + i * 4);
+
+ writel_relaxed(0xf0, cpu_base + GIC_CPU_PRIMASK);
+ writel_relaxed(1, cpu_base + GIC_CPU_CTRL);
+}
+
+static int gic_notifier(struct notifier_block *self, unsigned long cmd, void *v)
+{
+ int i;
+
+ for (i = 0; i < MAX_GIC_NR; i++) {
+ switch (cmd) {
+ case CPU_PM_ENTER:
+ gic_cpu_save(i);
+ break;
+ case CPU_PM_ENTER_FAILED:
+ case CPU_PM_EXIT:
+ gic_cpu_restore(i);
+ break;
+ case CPU_COMPLEX_PM_ENTER:
+ gic_dist_save(i);
+ break;
+ case CPU_COMPLEX_PM_ENTER_FAILED:
+ case CPU_COMPLEX_PM_EXIT:
+ gic_dist_restore(i);
+ break;
+ }
+ }
+
+ return NOTIFY_OK;
+}
+
+static struct notifier_block gic_notifier_block = {
+ .notifier_call = gic_notifier,
+};
+
+static void __init gic_cpu_pm_init(struct gic_chip_data *gic)
+{
+ gic->saved_ppi_enable = __alloc_percpu(DIV_ROUND_UP(32, 32) * 4,
+ sizeof(u32));
+ BUG_ON(!gic->saved_ppi_enable);
+
+ gic->saved_ppi_conf = __alloc_percpu(DIV_ROUND_UP(32, 16) * 4,
+ sizeof(u32));
+ BUG_ON(!gic->saved_ppi_conf);
+
+ gic->saved_ppi_pri = __alloc_percpu(DIV_ROUND_UP(32, 4) * 4,
+ sizeof(u32));
+ BUG_ON(!gic->saved_ppi_pri);
+
+ cpu_pm_register_notifier(&gic_notifier_block);
+}
+#else
+static void __init gic_cpu_pm_init(struct gic_chip_data *gic)
+{
+}
+#endif
+
void __init gic_init(unsigned int gic_nr, unsigned int irq_start,
void __iomem *dist_base, void __iomem *cpu_base)
{
@@ -367,6 +578,7 @@ void __init gic_init(unsigned int gic_nr, unsigned int irq_start,
gic_dist_init(gic, irq_start);
gic_cpu_init(gic);
+ gic_cpu_pm_init(gic);
}
void __cpuinit gic_secondary_init(unsigned int gic_nr)
--
1.7.4.1
next prev parent reply other threads:[~2011-06-13 0:43 UTC|newest]
Thread overview: 45+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-06-13 0:43 [PATCH 0/3] CPU PM notifiers Colin Cross
2011-06-13 0:43 ` Colin Cross
2011-06-13 0:43 ` [PATCH 1/3] ARM: Add cpu power management notifiers Colin Cross
2011-06-13 0:43 ` Colin Cross
2011-06-13 1:57 ` Rob Herring
2011-06-13 1:57 ` Rob Herring
2011-06-13 22:17 ` Kevin Hilman
2011-06-13 22:17 ` Kevin Hilman
2011-06-14 6:15 ` Colin Cross
2011-06-14 6:15 ` Colin Cross
2011-06-16 0:12 ` Kevin Hilman
2011-06-16 0:12 ` Kevin Hilman
2011-06-13 0:43 ` Colin Cross [this message]
2011-06-13 0:43 ` [PATCH 2/3] ARM: gic: Use cpu pm notifiers to save gic state Colin Cross
2011-06-13 10:41 ` Lorenzo Pieralisi
2011-06-13 10:41 ` Lorenzo Pieralisi
2011-06-13 0:43 ` [PATCH 3/3] ARM: vfp: Use cpu pm notifiers to save vfp state Colin Cross
2011-06-13 0:43 ` Colin Cross
2011-06-13 18:37 ` [PATCH 0/3] CPU PM notifiers Rafael J. Wysocki
2011-06-13 18:37 ` Rafael J. Wysocki
2011-06-13 18:37 ` Rafael J. Wysocki
2011-06-13 18:55 ` Colin Cross
2011-06-13 18:55 ` Colin Cross
2011-06-13 18:55 ` Colin Cross
2011-06-14 21:00 ` Rafael J. Wysocki
2011-06-14 21:00 ` Rafael J. Wysocki
2011-06-14 21:00 ` Rafael J. Wysocki
2011-06-14 21:19 ` Colin Cross
2011-06-14 21:19 ` Colin Cross
2011-06-14 21:19 ` Colin Cross
2011-06-14 21:34 ` Rafael J. Wysocki
2011-06-14 21:34 ` Rafael J. Wysocki
2011-06-14 21:34 ` Rafael J. Wysocki
2011-06-14 21:40 ` Colin Cross
2011-06-14 21:40 ` Colin Cross
2011-06-14 21:40 ` Colin Cross
2011-06-14 22:12 ` Rafael J. Wysocki
2011-06-14 22:12 ` Rafael J. Wysocki
2011-06-14 22:12 ` Rafael J. Wysocki
2011-06-15 6:54 ` Santosh Shilimkar
2011-06-15 6:54 ` Santosh Shilimkar
2011-06-15 6:54 ` Santosh Shilimkar
2011-06-15 23:13 ` Rafael J. Wysocki
2011-06-15 23:13 ` Rafael J. Wysocki
2011-06-15 23:13 ` Rafael J. Wysocki
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1307925825-28566-3-git-send-email-ccross@android.com \
--to=ccross@android.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.