From: Dan McGee <dpmcgee@gmail.com>
To: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org, Jeff Garzik <jgarzik@pobox.com>,
Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Subject: [PATCH 5/5] pata_sis: code style cleanups for consistency
Date: Wed, 7 Sep 2011 11:23:22 -0500 [thread overview]
Message-ID: <1315412602-6560-6-git-send-email-dpmcgee@gmail.com> (raw)
In-Reply-To: <1315412602-6560-1-git-send-email-dpmcgee@gmail.com>
Remove a lot of ' ' (double spaces) as well as ensuring use of tabs vs.
spaces is appropriate and consistent.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
---
drivers/ata/pata_sis.c | 38 +++++++++++++++++++-------------------
1 files changed, 19 insertions(+), 19 deletions(-)
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index d886b0b..b0edc7d 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -55,7 +55,7 @@ static const struct sis_laptop sis_laptop[] = {
/* devid, subvendor, subdev */
{ 0x5513, 0x1043, 0x1107 }, /* ASUS A6K */
{ 0x5513, 0x1734, 0x105F }, /* FSC Amilo A1630 */
- { 0x5513, 0x1071, 0x8640 }, /* EasyNote K5305 */
+ { 0x5513, 0x1071, 0x8640 }, /* EasyNote K5305 */
/* end marker */
{ 0, }
};
@@ -76,7 +76,7 @@ static int sis_short_ata40(struct pci_dev *dev)
}
/**
- * sis_old_port_base - return PCI configuration base for dev
+ * sis_old_port_base - return PCI configuration base for dev
* @adev: device
*
* Returns the base of the PCI configuration registers for this port
@@ -85,11 +85,11 @@ static int sis_short_ata40(struct pci_dev *dev)
static int sis_old_port_base(struct ata_device *adev)
{
- return 0x40 + (4 * adev->link->ap->port_no) + (2 * adev->devno);
+ return 0x40 + (4 * adev->link->ap->port_no) + (2 * adev->devno);
}
/**
- * sis_port_base - return PCI configuration base for dev
+ * sis_port_base - return PCI configuration base for dev
* @adev: device
*
* Returns the base of the PCI configuration registers for this port
@@ -112,7 +112,7 @@ static int sis_port_base(struct ata_device *adev)
}
/**
- * sis_133_cable_detect - check for 40/80 pin
+ * sis_133_cable_detect - check for 40/80 pin
* @ap: Port
* @deadline: deadline jiffies for the operation
*
@@ -133,7 +133,7 @@ static int sis_133_cable_detect(struct ata_port *ap)
}
/**
- * sis_66_cable_detect - check for 40/80 pin
+ * sis_66_cable_detect - check for 40/80 pin
* @ap: Port
*
* Perform cable detection on the UDMA66, UDMA100 and early UDMA133
@@ -155,7 +155,7 @@ static int sis_66_cable_detect(struct ata_port *ap)
/**
- * sis_pre_reset - probe begin
+ * sis_pre_reset - probe begin
* @link: ATA link
* @deadline: deadline jiffies for the operation
*
@@ -183,7 +183,7 @@ static int sis_pre_reset(struct ata_link *link, unsigned long deadline)
/**
- * sis_set_fifo - Set RWP fifo bits for this device
+ * sis_set_fifo - Set RWP fifo bits for this device
* @ap: Port
* @adev: Device
*
@@ -226,7 +226,7 @@ static void sis_set_fifo(struct ata_port *ap, struct ata_device *adev)
static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int port = sis_old_port_base(adev);
u8 t1, t2;
int speed = adev->pio_mode - XFER_PIO_0;
@@ -263,7 +263,7 @@ static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev)
static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int port = sis_old_port_base(adev);
int speed = adev->pio_mode - XFER_PIO_0;
@@ -288,7 +288,7 @@ static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev)
static void sis_133_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int port;
u32 t1;
int speed = adev->pio_mode - XFER_PIO_0;
@@ -336,7 +336,7 @@ static void sis_133_set_piomode (struct ata_port *ap, struct ata_device *adev)
static void sis_old_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
int drive_pci = sis_old_port_base(adev);
u16 timing;
@@ -375,7 +375,7 @@ static void sis_old_set_dmamode (struct ata_port *ap, struct ata_device *adev)
static void sis_66_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
int drive_pci = sis_old_port_base(adev);
u16 timing;
@@ -414,7 +414,7 @@ static void sis_66_set_dmamode (struct ata_port *ap, struct ata_device *adev)
static void sis_100_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
int drive_pci = sis_old_port_base(adev);
u8 timing;
@@ -448,7 +448,7 @@ static void sis_100_set_dmamode (struct ata_port *ap, struct ata_device *adev)
static void sis_133_early_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
int drive_pci = sis_old_port_base(adev);
u8 timing;
@@ -481,7 +481,7 @@ static void sis_133_early_set_dmamode (struct ata_port *ap, struct ata_device *a
static void sis_133_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int port;
u32 t1;
@@ -710,7 +710,7 @@ static void sis_fixup(struct pci_dev *pdev, struct sis_chipset *sis)
* @pdev: PCI device to register
* @ent: Entry in sis_pci_tbl matching with @pdev
*
- * Called from kernel PCI layer. We probe for combined mode (sigh),
+ * Called from kernel PCI layer. We probe for combined mode (sigh),
* and then hand over control to libata, for it to do the rest.
*
* LOCKING:
@@ -820,10 +820,10 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
}
break;
case 0x0180: /* SIS 965/965L */
- chipset = &sis133;
+ chipset = &sis133;
break;
case 0x1180: /* SIS 966/966L */
- chipset = &sis133;
+ chipset = &sis133;
break;
}
}
--
1.7.6.1
prev parent reply other threads:[~2011-09-07 16:23 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-07 16:23 [PATCH 0/5 v2] pata_sis fixes and driver cleanup Dan McGee
2011-09-07 16:23 ` [PATCH 1/5] pata_sis: extract a sis_port_base() method Dan McGee
2011-09-07 16:23 ` [PATCH 2/5] pata_sis: add mode_filter method for certain sis5513 chipsets Dan McGee
2011-09-07 16:23 ` [PATCH 3/5] pata_sis: enable MWDMA for UDMA 133 chipset Dan McGee
2011-09-07 16:23 ` [PATCH 4/5] pata_sis: mark most const data static as well Dan McGee
2011-09-07 16:23 ` Dan McGee [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1315412602-6560-6-git-send-email-dpmcgee@gmail.com \
--to=dpmcgee@gmail.com \
--cc=bzolnier@gmail.com \
--cc=jgarzik@pobox.com \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.