From: Zhicheng Fan <B32736@freescale.com>
To: <linuxppc-dev@lists.ozlabs.org>, <galak@kernel.crashing.org>
Cc: Zhicheng Fan <b32736@freescale.com>
Subject: [PATCH 2/2 v5] powerpc/dts: Add dts for p1020rdb-pc board
Date: Fri, 10 Feb 2012 14:48:16 +0800 [thread overview]
Message-ID: <1328856496-2873-2-git-send-email-B32736@freescale.com> (raw)
In-Reply-To: <1328856496-2873-1-git-send-email-B32736@freescale.com>
From: Zhicheng Fan <b32736@freescale.com>
P1020RDB-PC Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
10 16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using VitesseTM VSC7385 L2 switch
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
---
arch/powerpc/boot/dts/p1020rdb-pc.dtsi | 247 ++++++++++++++++++++++
arch/powerpc/boot/dts/p1020rdb-pc_32b.dts | 90 ++++++++
arch/powerpc/boot/dts/p1020rdb-pc_36b.dts | 90 ++++++++
arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts | 64 ++++++
arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts | 142 +++++++++++++
5 files changed, 633 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc.dtsi
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc_32b.dts
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc_36b.dts
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc.dtsi b/arch/powerpc/boot/dts/p1020rdb-pc.dtsi
new file mode 100644
index 0000000..c952cd3
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc.dtsi
@@ -0,0 +1,247 @@
+/*
+ * P1020 RDB-PC Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x1000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 256KB for Vitesse 7385 Switch firmware */
+ reg = <0x0 0x00040000>;
+ label = "NOR Vitesse-7385 Firmware";
+ read-only;
+ };
+
+ partition@40000 {
+ /* 256KB for DTB Image */
+ reg = <0x00040000 0x00040000>;
+ label = "NOR DTB Image";
+ };
+
+ partition@80000 {
+ /* 3.5 MB for Linux Kernel Image */
+ reg = <0x00080000 0x00380000>;
+ label = "NOR Linux Kernel Image";
+ };
+
+ partition@400000 {
+ /* 11MB for JFFS2 based Root file System */
+ reg = <0x00400000 0x00b00000>;
+ label = "NOR JFFS2 Root File System";
+ };
+
+ partition@f00000 {
+ /* This location must not be altered */
+ /* 512KB for u-boot Bootloader Image */
+ /* 512KB for u-boot Environment Variables */
+ reg = <0x00f00000 0x00100000>;
+ label = "NOR U-Boot Image";
+ read-only;
+ };
+ };
+
+ nand@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p1020-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <0x1 0x0 0x40000>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 1MB for u-boot Bootloader Image */
+ reg = <0x0 0x00100000>;
+ label = "NAND U-Boot Image";
+ read-only;
+ };
+
+ partition@100000 {
+ /* 1MB for DTB Image */
+ reg = <0x00100000 0x00100000>;
+ label = "NAND DTB Image";
+ };
+
+ partition@200000 {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00200000 0x00400000>;
+ label = "NAND Linux Kernel Image";
+ };
+
+ partition@600000 {
+ /* 4MB for Compressed Root file System Image */
+ reg = <0x00600000 0x00400000>;
+ label = "NAND Compressed RFS Image";
+ };
+
+ partition@a00000 {
+ /* 7MB for JFFS2 based Root file System */
+ reg = <0x00a00000 0x00700000>;
+ label = "NAND JFFS2 Root File System";
+ };
+
+ partition@1100000 {
+ /* 15MB for JFFS2 based Root file System */
+ reg = <0x01100000 0x00f00000>;
+ label = "NAND Writable User area";
+ };
+ };
+
+ L2switch@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "vitesse-7385";
+ reg = <0x2 0x0 0x20000>;
+ };
+
+ cpld@3,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cpld";
+ reg = <0x3 0x0 0x20000>;
+ read-only;
+ };
+};
+
+&soc {
+ i2c@3000 {
+ rtc@68 {
+ compatible = "pericom,pt7c4338";
+ reg = <0x68>;
+ };
+ };
+
+ spi@7000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>; /* input clock */
+
+ partition@u-boot {
+ /* 512KB for u-boot Bootloader Image */
+ reg = <0x0 0x00080000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ partition@dtb {
+ /* 512KB for DTB Image*/
+ reg = <0x00080000 0x00080000>;
+ label = "dtb";
+ };
+
+ partition@kernel {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00100000 0x00400000>;
+ label = "kernel";
+ };
+
+ partition@fs {
+ /* 4MB for Compressed RFS Image */
+ reg = <0x00500000 0x00400000>;
+ label = "file system";
+ };
+
+ partition@jffs-fs {
+ /* 7MB for JFFS2 based RFS */
+ reg = <0x00900000 0x00700000>;
+ label = "file system jffs2";
+ };
+ };
+ };
+
+ usb@22000 {
+ phy_type = "ulpi";
+ };
+
+ /* USB2 is shared with localbus, so it must be disabled
+ by default. We can't put 'status = "disabled";' here
+ since U-Boot doesn't clear the status property when
+ it enables USB2. OTOH, U-Boot does create a new node
+ when there isn't any. So, just comment it out.
+ usb@23000 {
+ phy_type = "ulpi";
+ };
+ */
+
+ mdio@24000 {
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <3 1>;
+ reg = <0x0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <2 1>;
+ reg = <0x1>;
+ };
+
+ tbi0: tbi-phy@11 {
+ device_type = "tbi-phy";
+ reg = <0x11>;
+ };
+ };
+
+ mdio@25000 {
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet@b0000 {
+ fixed-link = <1 1 1000 0 0>;
+ phy-connection-type = "rgmii-id";
+
+ };
+
+ enet1: ethernet@b1000 {
+ phy-handle = <&phy0>;
+ tbi-handle = <&tbi1>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet2: ethernet@b2000 {
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc_32b.dts b/arch/powerpc/boot/dts/p1020rdb-pc_32b.dts
new file mode 100644
index 0000000..4de69b7
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc_32b.dts
@@ -0,0 +1,90 @@
+/*
+ * P1020 RDB-PC Device Tree Source (32-bit address map)
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/p1020si-pre.dtsi"
+/ {
+ model = "fsl,P1020RDB-PC";
+ compatible = "fsl,P1020RDB-PC";
+
+ memory {
+ device_type = "memory";
+ };
+
+ lbc: localbus@ffe05000 {
+ reg = <0 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes and Vitesse 5 port L2 switch */
+ ranges = <0x0 0x0 0x0 0xef000000 0x01000000
+ 0x1 0x0 0x0 0xff800000 0x00040000
+ 0x2 0x0 0x0 0xffb00000 0x00020000
+ 0x3 0x0 0x0 0xffa00000 0x00020000>;
+ };
+
+ soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@ffe09000 {
+ ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+ reg = <0 0xffe09000 0 0x1000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@ffe0a000 {
+ reg = <0 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+};
+
+/include/ "p1020rdb-pc.dtsi"
+/include/ "fsl/p1020si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc_36b.dts b/arch/powerpc/boot/dts/p1020rdb-pc_36b.dts
new file mode 100644
index 0000000..5237da7
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc_36b.dts
@@ -0,0 +1,90 @@
+/*
+ * P1020 RDB-PC Device Tree Source (36-bit address map)
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/p1020si-pre.dtsi"
+/ {
+ model = "fsl,P1020RDB-PC";
+ compatible = "fsl,P1020RDB-PC";
+
+ memory {
+ device_type = "memory";
+ };
+
+ lbc: localbus@fffe05000 {
+ reg = <0xf 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes and Vitesse 5 port L2 switch */
+ ranges = <0x0 0x0 0xf 0xef000000 0x01000000
+ 0x1 0x0 0xf 0xff800000 0x00040000
+ 0x2 0x0 0xf 0xffb00000 0x00040000
+ 0x3 0x0 0xf 0xffa00000 0x00020000>;
+ };
+
+ soc: soc@fffe00000 {
+ ranges = <0x0 0xf 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@fffe09000 {
+ reg = <0xf 0xffe09000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xc0000000 0xc 0x20000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xc0000000
+ 0x2000000 0x0 0xc0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@fffe0a000 {
+ reg = <0xf 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0x80000000 0xc 0x00000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+};
+
+/include/ "p1020rdb-pc.dtsi"
+/include/ "fsl/p1020si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts b/arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts
new file mode 100644
index 0000000..f411515
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts
@@ -0,0 +1,64 @@
+/*
+ * P1020 RDB-PC Core0 Device Tree Source in CAMP mode.
+ *
+ * In CAMP mode, each core needs to have its own dts. Only mpic and L2 cache
+ * can be shared, all the other devices must be assigned to one core only.
+ * This dts file allows core0 to have memory, l2, i2c, spi, gpio, tdm, dma, usb,
+ * eth1, eth2, sdhc, crypto, global-util, message, pci0, pci1, msi.
+ *
+ * Please note to add "-b 0" for core0's dts compiling.
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/include/ "p1020rdb-pc_32b.dts"
+
+/ {
+ model = "fsl,P1020RDB-PC";
+ compatible = "fsl,P1020RDB-PC";
+
+ aliases {
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ serial0 = &serial0;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ PowerPC,P1020@1 {
+ status = "disabled";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ localbus@ffe05000 {
+ status = "disabled";
+ };
+
+ soc@ffe00000 {
+ serial1: serial@4600 {
+ status = "disabled";
+ };
+
+ enet0: ethernet@b0000 {
+ status = "disabled";
+ };
+
+ mpic: pic@40000 {
+ protected-sources = <
+ 42 29 30 34 /* serial1, enet0-queue-group0 */
+ 17 18 24 45 /* enet0-queue-group1, crypto */
+ >;
+ pic-no-reset;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts b/arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts
new file mode 100644
index 0000000..a91335a
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts
@@ -0,0 +1,142 @@
+/*
+ * P1020 RDB-PC Core1 Device Tree Source in CAMP mode.
+ *
+ * In CAMP mode, each core needs to have its own dts. Only mpic and L2 cache
+ * can be shared, all the other devices must be assigned to one core only.
+ * This dts allows core1 to have l2, eth0, crypto.
+ *
+ * Please note to add "-b 1" for core1's dts compiling.
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/include/ "p1020rdb-pc_32b.dts"
+
+/ {
+ model = "fsl,P1020RDB-PC";
+ compatible = "fsl,P1020RDB-PC";
+
+ aliases {
+ ethernet0 = &enet0;
+ serial0 = &serial1;
+ };
+
+ cpus {
+ PowerPC,P1020@0 {
+ status = "disabled";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ localbus@ffe05000 {
+ status = "disabled";
+ };
+
+ soc@ffe00000 {
+ ecm-law@0 {
+ status = "disabled";
+ };
+
+ ecm@1000 {
+ status = "disabled";
+ };
+
+ memory-controller@2000 {
+ status = "disabled";
+ };
+
+ i2c@3000 {
+ status = "disabled";
+ };
+
+ i2c@3100 {
+ status = "disabled";
+ };
+
+ serial0: serial@4500 {
+ status = "disabled";
+ };
+
+ spi@7000 {
+ status = "disabled";
+ };
+
+ gpio: gpio-controller@f000 {
+ status = "disabled";
+ };
+
+ dma@21300 {
+ status = "disabled";
+ };
+
+ mdio@24000 {
+ status = "disabled";
+ };
+
+ mdio@25000 {
+ status = "disabled";
+ };
+
+ enet1: ethernet@b1000 {
+ status = "disabled";
+ };
+
+ enet2: ethernet@b2000 {
+ status = "disabled";
+ };
+
+ usb@22000 {
+ status = "disabled";
+ };
+
+ sdhci@2e000 {
+ status = "disabled";
+ };
+
+ mpic: pic@40000 {
+ protected-sources = <
+ 16 /* ecm, mem, L2, pci0, pci1 */
+ 43 42 59 /* i2c, serial0, spi */
+ 47 63 62 /* gpio, tdm */
+ 20 21 22 23 /* dma */
+ 03 02 /* mdio */
+ 35 36 40 /* enet1-queue-group0 */
+ 51 52 67 /* enet1-queue-group1 */
+ 31 32 33 /* enet2-queue-group0 */
+ 25 26 27 /* enet2-queue-group1 */
+ 28 72 58 /* usb, sdhci, crypto */
+ 0xb0 0xb1 0xb2 /* message */
+ 0xb3 0xb4 0xb5
+ 0xb6 0xb7
+ 0xe0 0xe1 0xe2 /* msi */
+ 0xe3 0xe4 0xe5
+ 0xe6 0xe7 /* sdhci, crypto , pci */
+ >;
+ pic-no-reset;
+ };
+
+ msi@41600 {
+ status = "disabled";
+ };
+
+ global-utilities@e0000 { //global utilities block
+ status = "disabled";
+ };
+ };
+
+ pci0: pcie@ffe09000 {
+ status = "disabled";
+ };
+
+ pci1: pcie@ffe0a000 {
+ status = "disabled";
+ };
+};
--
1.7.0.4
next prev parent reply other threads:[~2012-02-10 6:51 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-02-10 6:48 [PATCH 1/2 v5] powerpc/85xx: Add p1020rdb-pc platform support Zhicheng Fan
2012-02-10 6:48 ` Zhicheng Fan [this message]
2012-03-16 16:04 ` [PATCH 2/2 v5] powerpc/dts: Add dts for p1020rdb-pc board Kumar Gala
2012-03-16 16:04 ` [PATCH 1/2 v5] powerpc/85xx: Add p1020rdb-pc platform support Kumar Gala
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1328856496-2873-2-git-send-email-B32736@freescale.com \
--to=b32736@freescale.com \
--cc=galak@kernel.crashing.org \
--cc=linuxppc-dev@lists.ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.