* [PATCH 2/2 v5] powerpc/dts: Add dts for p1020rdb-pc board
2012-02-10 6:48 [PATCH 1/2 v5] powerpc/85xx: Add p1020rdb-pc platform support Zhicheng Fan
@ 2012-02-10 6:48 ` Zhicheng Fan
2012-03-16 16:04 ` Kumar Gala
2012-03-16 16:04 ` [PATCH 1/2 v5] powerpc/85xx: Add p1020rdb-pc platform support Kumar Gala
1 sibling, 1 reply; 4+ messages in thread
From: Zhicheng Fan @ 2012-02-10 6:48 UTC (permalink / raw)
To: linuxppc-dev, galak; +Cc: Zhicheng Fan
From: Zhicheng Fan <b32736@freescale.com>
P1020RDB-PC Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
10 16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using VitesseTM VSC7385 L2 switch
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
---
arch/powerpc/boot/dts/p1020rdb-pc.dtsi | 247 ++++++++++++++++++++++
arch/powerpc/boot/dts/p1020rdb-pc_32b.dts | 90 ++++++++
arch/powerpc/boot/dts/p1020rdb-pc_36b.dts | 90 ++++++++
arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts | 64 ++++++
arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts | 142 +++++++++++++
5 files changed, 633 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc.dtsi
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc_32b.dts
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc_36b.dts
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc.dtsi b/arch/powerpc/boot/dts/p1020rdb-pc.dtsi
new file mode 100644
index 0000000..c952cd3
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc.dtsi
@@ -0,0 +1,247 @@
+/*
+ * P1020 RDB-PC Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x1000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 256KB for Vitesse 7385 Switch firmware */
+ reg = <0x0 0x00040000>;
+ label = "NOR Vitesse-7385 Firmware";
+ read-only;
+ };
+
+ partition@40000 {
+ /* 256KB for DTB Image */
+ reg = <0x00040000 0x00040000>;
+ label = "NOR DTB Image";
+ };
+
+ partition@80000 {
+ /* 3.5 MB for Linux Kernel Image */
+ reg = <0x00080000 0x00380000>;
+ label = "NOR Linux Kernel Image";
+ };
+
+ partition@400000 {
+ /* 11MB for JFFS2 based Root file System */
+ reg = <0x00400000 0x00b00000>;
+ label = "NOR JFFS2 Root File System";
+ };
+
+ partition@f00000 {
+ /* This location must not be altered */
+ /* 512KB for u-boot Bootloader Image */
+ /* 512KB for u-boot Environment Variables */
+ reg = <0x00f00000 0x00100000>;
+ label = "NOR U-Boot Image";
+ read-only;
+ };
+ };
+
+ nand@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p1020-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <0x1 0x0 0x40000>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 1MB for u-boot Bootloader Image */
+ reg = <0x0 0x00100000>;
+ label = "NAND U-Boot Image";
+ read-only;
+ };
+
+ partition@100000 {
+ /* 1MB for DTB Image */
+ reg = <0x00100000 0x00100000>;
+ label = "NAND DTB Image";
+ };
+
+ partition@200000 {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00200000 0x00400000>;
+ label = "NAND Linux Kernel Image";
+ };
+
+ partition@600000 {
+ /* 4MB for Compressed Root file System Image */
+ reg = <0x00600000 0x00400000>;
+ label = "NAND Compressed RFS Image";
+ };
+
+ partition@a00000 {
+ /* 7MB for JFFS2 based Root file System */
+ reg = <0x00a00000 0x00700000>;
+ label = "NAND JFFS2 Root File System";
+ };
+
+ partition@1100000 {
+ /* 15MB for JFFS2 based Root file System */
+ reg = <0x01100000 0x00f00000>;
+ label = "NAND Writable User area";
+ };
+ };
+
+ L2switch@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "vitesse-7385";
+ reg = <0x2 0x0 0x20000>;
+ };
+
+ cpld@3,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cpld";
+ reg = <0x3 0x0 0x20000>;
+ read-only;
+ };
+};
+
+&soc {
+ i2c@3000 {
+ rtc@68 {
+ compatible = "pericom,pt7c4338";
+ reg = <0x68>;
+ };
+ };
+
+ spi@7000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>; /* input clock */
+
+ partition@u-boot {
+ /* 512KB for u-boot Bootloader Image */
+ reg = <0x0 0x00080000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ partition@dtb {
+ /* 512KB for DTB Image*/
+ reg = <0x00080000 0x00080000>;
+ label = "dtb";
+ };
+
+ partition@kernel {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00100000 0x00400000>;
+ label = "kernel";
+ };
+
+ partition@fs {
+ /* 4MB for Compressed RFS Image */
+ reg = <0x00500000 0x00400000>;
+ label = "file system";
+ };
+
+ partition@jffs-fs {
+ /* 7MB for JFFS2 based RFS */
+ reg = <0x00900000 0x00700000>;
+ label = "file system jffs2";
+ };
+ };
+ };
+
+ usb@22000 {
+ phy_type = "ulpi";
+ };
+
+ /* USB2 is shared with localbus, so it must be disabled
+ by default. We can't put 'status = "disabled";' here
+ since U-Boot doesn't clear the status property when
+ it enables USB2. OTOH, U-Boot does create a new node
+ when there isn't any. So, just comment it out.
+ usb@23000 {
+ phy_type = "ulpi";
+ };
+ */
+
+ mdio@24000 {
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <3 1>;
+ reg = <0x0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <2 1>;
+ reg = <0x1>;
+ };
+
+ tbi0: tbi-phy@11 {
+ device_type = "tbi-phy";
+ reg = <0x11>;
+ };
+ };
+
+ mdio@25000 {
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet@b0000 {
+ fixed-link = <1 1 1000 0 0>;
+ phy-connection-type = "rgmii-id";
+
+ };
+
+ enet1: ethernet@b1000 {
+ phy-handle = <&phy0>;
+ tbi-handle = <&tbi1>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet2: ethernet@b2000 {
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc_32b.dts b/arch/powerpc/boot/dts/p1020rdb-pc_32b.dts
new file mode 100644
index 0000000..4de69b7
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc_32b.dts
@@ -0,0 +1,90 @@
+/*
+ * P1020 RDB-PC Device Tree Source (32-bit address map)
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/p1020si-pre.dtsi"
+/ {
+ model = "fsl,P1020RDB-PC";
+ compatible = "fsl,P1020RDB-PC";
+
+ memory {
+ device_type = "memory";
+ };
+
+ lbc: localbus@ffe05000 {
+ reg = <0 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes and Vitesse 5 port L2 switch */
+ ranges = <0x0 0x0 0x0 0xef000000 0x01000000
+ 0x1 0x0 0x0 0xff800000 0x00040000
+ 0x2 0x0 0x0 0xffb00000 0x00020000
+ 0x3 0x0 0x0 0xffa00000 0x00020000>;
+ };
+
+ soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@ffe09000 {
+ ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+ reg = <0 0xffe09000 0 0x1000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@ffe0a000 {
+ reg = <0 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+};
+
+/include/ "p1020rdb-pc.dtsi"
+/include/ "fsl/p1020si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc_36b.dts b/arch/powerpc/boot/dts/p1020rdb-pc_36b.dts
new file mode 100644
index 0000000..5237da7
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc_36b.dts
@@ -0,0 +1,90 @@
+/*
+ * P1020 RDB-PC Device Tree Source (36-bit address map)
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/p1020si-pre.dtsi"
+/ {
+ model = "fsl,P1020RDB-PC";
+ compatible = "fsl,P1020RDB-PC";
+
+ memory {
+ device_type = "memory";
+ };
+
+ lbc: localbus@fffe05000 {
+ reg = <0xf 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes and Vitesse 5 port L2 switch */
+ ranges = <0x0 0x0 0xf 0xef000000 0x01000000
+ 0x1 0x0 0xf 0xff800000 0x00040000
+ 0x2 0x0 0xf 0xffb00000 0x00040000
+ 0x3 0x0 0xf 0xffa00000 0x00020000>;
+ };
+
+ soc: soc@fffe00000 {
+ ranges = <0x0 0xf 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@fffe09000 {
+ reg = <0xf 0xffe09000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xc0000000 0xc 0x20000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xc0000000
+ 0x2000000 0x0 0xc0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@fffe0a000 {
+ reg = <0xf 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0x80000000 0xc 0x00000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+};
+
+/include/ "p1020rdb-pc.dtsi"
+/include/ "fsl/p1020si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts b/arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts
new file mode 100644
index 0000000..f411515
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts
@@ -0,0 +1,64 @@
+/*
+ * P1020 RDB-PC Core0 Device Tree Source in CAMP mode.
+ *
+ * In CAMP mode, each core needs to have its own dts. Only mpic and L2 cache
+ * can be shared, all the other devices must be assigned to one core only.
+ * This dts file allows core0 to have memory, l2, i2c, spi, gpio, tdm, dma, usb,
+ * eth1, eth2, sdhc, crypto, global-util, message, pci0, pci1, msi.
+ *
+ * Please note to add "-b 0" for core0's dts compiling.
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/include/ "p1020rdb-pc_32b.dts"
+
+/ {
+ model = "fsl,P1020RDB-PC";
+ compatible = "fsl,P1020RDB-PC";
+
+ aliases {
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ serial0 = &serial0;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ PowerPC,P1020@1 {
+ status = "disabled";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ localbus@ffe05000 {
+ status = "disabled";
+ };
+
+ soc@ffe00000 {
+ serial1: serial@4600 {
+ status = "disabled";
+ };
+
+ enet0: ethernet@b0000 {
+ status = "disabled";
+ };
+
+ mpic: pic@40000 {
+ protected-sources = <
+ 42 29 30 34 /* serial1, enet0-queue-group0 */
+ 17 18 24 45 /* enet0-queue-group1, crypto */
+ >;
+ pic-no-reset;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts b/arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts
new file mode 100644
index 0000000..a91335a
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts
@@ -0,0 +1,142 @@
+/*
+ * P1020 RDB-PC Core1 Device Tree Source in CAMP mode.
+ *
+ * In CAMP mode, each core needs to have its own dts. Only mpic and L2 cache
+ * can be shared, all the other devices must be assigned to one core only.
+ * This dts allows core1 to have l2, eth0, crypto.
+ *
+ * Please note to add "-b 1" for core1's dts compiling.
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/include/ "p1020rdb-pc_32b.dts"
+
+/ {
+ model = "fsl,P1020RDB-PC";
+ compatible = "fsl,P1020RDB-PC";
+
+ aliases {
+ ethernet0 = &enet0;
+ serial0 = &serial1;
+ };
+
+ cpus {
+ PowerPC,P1020@0 {
+ status = "disabled";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ localbus@ffe05000 {
+ status = "disabled";
+ };
+
+ soc@ffe00000 {
+ ecm-law@0 {
+ status = "disabled";
+ };
+
+ ecm@1000 {
+ status = "disabled";
+ };
+
+ memory-controller@2000 {
+ status = "disabled";
+ };
+
+ i2c@3000 {
+ status = "disabled";
+ };
+
+ i2c@3100 {
+ status = "disabled";
+ };
+
+ serial0: serial@4500 {
+ status = "disabled";
+ };
+
+ spi@7000 {
+ status = "disabled";
+ };
+
+ gpio: gpio-controller@f000 {
+ status = "disabled";
+ };
+
+ dma@21300 {
+ status = "disabled";
+ };
+
+ mdio@24000 {
+ status = "disabled";
+ };
+
+ mdio@25000 {
+ status = "disabled";
+ };
+
+ enet1: ethernet@b1000 {
+ status = "disabled";
+ };
+
+ enet2: ethernet@b2000 {
+ status = "disabled";
+ };
+
+ usb@22000 {
+ status = "disabled";
+ };
+
+ sdhci@2e000 {
+ status = "disabled";
+ };
+
+ mpic: pic@40000 {
+ protected-sources = <
+ 16 /* ecm, mem, L2, pci0, pci1 */
+ 43 42 59 /* i2c, serial0, spi */
+ 47 63 62 /* gpio, tdm */
+ 20 21 22 23 /* dma */
+ 03 02 /* mdio */
+ 35 36 40 /* enet1-queue-group0 */
+ 51 52 67 /* enet1-queue-group1 */
+ 31 32 33 /* enet2-queue-group0 */
+ 25 26 27 /* enet2-queue-group1 */
+ 28 72 58 /* usb, sdhci, crypto */
+ 0xb0 0xb1 0xb2 /* message */
+ 0xb3 0xb4 0xb5
+ 0xb6 0xb7
+ 0xe0 0xe1 0xe2 /* msi */
+ 0xe3 0xe4 0xe5
+ 0xe6 0xe7 /* sdhci, crypto , pci */
+ >;
+ pic-no-reset;
+ };
+
+ msi@41600 {
+ status = "disabled";
+ };
+
+ global-utilities@e0000 { //global utilities block
+ status = "disabled";
+ };
+ };
+
+ pci0: pcie@ffe09000 {
+ status = "disabled";
+ };
+
+ pci1: pcie@ffe0a000 {
+ status = "disabled";
+ };
+};
--
1.7.0.4
^ permalink raw reply related [flat|nested] 4+ messages in thread