* [U-Boot] [PATCH v3 1/4] nds32/ag102: add header support of ag102 soc [not found] <"CACCg+XMRYkOmrCRBDPpN1hQpvPX6CPHWzb87e1TPKewaH8j8tA@mail.gmail.com"> @ 2012-02-28 5:46 ` Macpaul Lin 2012-02-28 5:46 ` [U-Boot] [PATCH v3 2/4] nds32/ag102: add ag102 soc support Macpaul Lin ` (3 more replies) 0 siblings, 4 replies; 8+ messages in thread From: Macpaul Lin @ 2012-02-28 5:46 UTC (permalink / raw) To: u-boot From: Macpaul Lin <macpaul@andestech.com> Add device address offsets header of ag102 soc. Add ag102 into mach-types.h. Add asm-offsets.c for helping convert C headers into asm. Signed-off-by: Macpaul Lin <macpaul@andestech.com> --- Changes for v2-v3: - No change. arch/nds32/cpu/n1213/ag102/asm-offsets.c | 54 ++++++++++++++++ arch/nds32/include/asm/arch-ag102/ag102.h | 97 +++++++++++++++++++++++++++++ arch/nds32/include/asm/mach-types.h | 14 ++++ 3 files changed, 165 insertions(+), 0 deletions(-) create mode 100644 arch/nds32/cpu/n1213/ag102/asm-offsets.c create mode 100644 arch/nds32/include/asm/arch-ag102/ag102.h diff --git a/arch/nds32/cpu/n1213/ag102/asm-offsets.c b/arch/nds32/cpu/n1213/ag102/asm-offsets.c new file mode 100644 index 0000000..4769a95 --- /dev/null +++ b/arch/nds32/cpu/n1213/ag102/asm-offsets.c @@ -0,0 +1,54 @@ +/* + * Adapted from Linux v2.6.36 kernel: arch/powerpc/kernel/asm-offsets.c + * + * Generate definitions needed by assembly language modules. + * This code generates raw asm output which is post-processed to extract + * and format the required data. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <common.h> + +#include <linux/kbuild.h> + +int main(void) +{ +#ifdef CONFIG_FTSMC020 + OFFSET(FTSMC020_BANK0_CR, ftsmc020, bank[0].cr); + OFFSET(FTSMC020_BANK0_TPR, ftsmc020, bank[0].tpr); +#endif + BLANK(); +#ifdef CONFIG_FTAHBC020S + OFFSET(FTAHBC020S_SLAVE_BSR_6, ftahbc02s, s_bsr[6]); + OFFSET(FTAHBC020S_CR, ftahbc02s, cr); +#endif + BLANK(); +#ifdef CONFIG_ANDES_PCU + OFFSET(ANDES_PCU_PCS4, andes_pcu, pcs4.parm); /* 0x104 */ +#endif + BLANK(); +#ifdef CONFIG_DWCDDR21MCTL + OFFSET(DWCDDR21MCTL_CCR, dwcddr21mctl, ccr); /* 0x04 */ + OFFSET(DWCDDR21MCTL_DCR, dwcddr21mctl, dcr); /* 0x04 */ + OFFSET(DWCDDR21MCTL_IOCR, dwcddr21mctl, iocr); /* 0x08 */ + OFFSET(DWCDDR21MCTL_CSR, dwcddr21mctl, csr); /* 0x0c */ + OFFSET(DWCDDR21MCTL_DRR, dwcddr21mctl, drr); /* 0x10 */ + OFFSET(DWCDDR21MCTL_DLLCR0, dwcddr21mctl, dllcr[0]); /* 0x24 */ + OFFSET(DWCDDR21MCTL_DLLCR1, dwcddr21mctl, dllcr[1]); /* 0x28 */ + OFFSET(DWCDDR21MCTL_DLLCR2, dwcddr21mctl, dllcr[2]); /* 0x2c */ + OFFSET(DWCDDR21MCTL_DLLCR3, dwcddr21mctl, dllcr[3]); /* 0x30 */ + OFFSET(DWCDDR21MCTL_DLLCR4, dwcddr21mctl, dllcr[4]); /* 0x34 */ + OFFSET(DWCDDR21MCTL_DLLCR5, dwcddr21mctl, dllcr[5]); /* 0x38 */ + OFFSET(DWCDDR21MCTL_DLLCR6, dwcddr21mctl, dllcr[6]); /* 0x3c */ + OFFSET(DWCDDR21MCTL_DLLCR7, dwcddr21mctl, dllcr[7]); /* 0x40 */ + OFFSET(DWCDDR21MCTL_DLLCR8, dwcddr21mctl, dllcr[8]); /* 0x44 */ + OFFSET(DWCDDR21MCTL_DLLCR9, dwcddr21mctl, dllcr[9]); /* 0x48 */ + OFFSET(DWCDDR21MCTL_RSLR0, dwcddr21mctl, rslr[0]); /* 0x4c */ + OFFSET(DWCDDR21MCTL_RDGR0, dwcddr21mctl, rdgr[0]); /* 0x5c */ + OFFSET(DWCDDR21MCTL_DTAR, dwcddr21mctl, dtar); /* 0xa4 */ + OFFSET(DWCDDR21MCTL_MR, dwcddr21mctl, mr); /* 0x1f0 */ +#endif + return 0; +} diff --git a/arch/nds32/include/asm/arch-ag102/ag102.h b/arch/nds32/include/asm/arch-ag102/ag102.h new file mode 100644 index 0000000..a12a8c5 --- /dev/null +++ b/arch/nds32/include/asm/arch-ag102/ag102.h @@ -0,0 +1,97 @@ +/* + * Copyright (C) 2011 Andes Technology Corporation + * Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef __AG102_H +#define __AG102_H + +/* + * Hardware register bases + */ + +/* PCI Controller */ +#define CONFIG_FTPCI100_BASE 0x90000000 +/* LPC Controller */ +#define CONFIG_LPC_IO_BASE 0x90100000 +/* LPC Controller */ +#define CONFIG_LPC_BASE 0x90200000 + +/* NDS32 Data Local Memory 01 */ +#define CONFIG_NDS_DLM1_BASE 0x90300000 +/* NDS32 Data Local Memory 02 */ +#define CONFIG_NDS_DLM2_BASE 0x90400000 + +/* Synopsys DWC DDR2/1 Controller */ +#define CONFIG_DWCDDR21MCTL_BASE 0x90500000 +/* DMA Controller */ +#define CONFIG_FTDMAC020_BASE 0x90600000 +/* FTIDE020_S IDE (ATA) Controller */ +#define CONFIG_FTIDE020S_BASE 0x90700000 +/* USB OTG Controller */ +#define CONFIG_FZOTG266HD0A_BASE 0x90800000 +/* Andes L2 Cache Controller */ +#define CONFIG_NCEL2C100_BASE 0x90900000 +/* XGI XG22 GPU */ +#define CONFIG_XGI_XG22_BASE 0x90A00000 +/* GMAC Ethernet Controller */ +#define CONFIG_FTGMAC100_BASE 0x90B00000 +/* AHB Controller */ +#define CONFIG_FTAHBC020S_BASE 0x90C00000 +/* AHB-to-APB Bridge Controller */ +#define CONFIG_FTAPBBRG020S_01_BASE 0x90D00000 +/* External AHB2AHB Controller */ +#define CONFIG_EXT_AHB2AHB_BASE 0x90E00000 +/* Andes Multi-core Interrupt Controller */ +#define CONFIG_NCEMIC100_BASE 0x90F00000 + +/* + * APB Device definitions + */ +/* Compat Flash Controller */ +#define CONFIG_FTCFC010_BASE 0x94000000 +/* APB - SSP (SPI) (without AC97) Controller */ +#define CONFIG_FTSSP010_01_BASE 0x94100000 +/* UART1 - APB STUART Controller (UART0 in Linux) */ +#define CONFIG_FTUART010_01_BASE 0x94200000 +/* FTSDC010 SD Controller */ +#define CONFIG_FTSDC010_BASE 0x94400000 +/* APB - SSP with HDA/AC97 Controller */ +#define CONFIG_FTSSP010_02_BASE 0x94500000 +/* UART2 - APB STUART Controller (UART1 in Linux) */ +#define CONFIG_FTUART010_02_BASE 0x94600000 +/* PCU Controller */ +#define CONFIG_ANDES_PCU_BASE 0x94800000 +/* FTTMR010 Timer */ +#define CONFIG_FTTMR010_BASE 0x94900000 +/* Watch Dog Controller */ +#define CONFIG_FTWDT010_BASE 0x94A00000 +/* FTRTC010 Real Time Clock */ +#define CONFIG_FTRTC010_BASE 0x98B00000 +/* GPIO Controller */ +#define CONFIG_FTGPIO010_BASE 0x94C00000 +/* I2C Controller */ +#define CONFIG_FTIIC010_BASE 0x94E00000 +/* PWM - Pulse Width Modulator Controller */ +#define CONFIG_FTPWM010_BASE 0x94F00000 + +/* Debug LED */ +#define CONFIG_DEBUG_LED 0x902FFFFC +/* Power Management Unit */ +#define CONFIG_FTPMU010_BASE 0x98100000 + +#endif /* __AG102_H */ diff --git a/arch/nds32/include/asm/mach-types.h b/arch/nds32/include/asm/mach-types.h index 7b52b98..259e4e7 100644 --- a/arch/nds32/include/asm/mach-types.h +++ b/arch/nds32/include/asm/mach-types.h @@ -40,4 +40,18 @@ extern unsigned int __machine_arch_type; # define machine_is_adpag101p() (1) #endif +#define MACH_TYPE_ADPAG102 2 + +#ifdef CONFIG_ARCH_ADPAG102 +# ifdef machine_arch_type +# undef machine_arch_type +# define machine_arch_type __machine_arch_type +# else +# define machine_arch_type MACH_TYPE_ADPAG102 +# endif +# define machine_is_adpag102() (machine_arch_type == MACH_TYPE_ADPAG102) +#else +# define machine_is_adpag102() (2) +#endif + #endif /* __ASM_NDS32_MACH_TYPE_H */ -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v3 2/4] nds32/ag102: add ag102 soc support 2012-02-28 5:46 ` [U-Boot] [PATCH v3 1/4] nds32/ag102: add header support of ag102 soc Macpaul Lin @ 2012-02-28 5:46 ` Macpaul Lin 2012-04-22 8:55 ` Macpaul Lin 2012-02-28 5:46 ` [U-Boot] [PATCH v3 3/4] board/adp-ag102: add board specific files Macpaul Lin ` (2 subsequent siblings) 3 siblings, 1 reply; 8+ messages in thread From: Macpaul Lin @ 2012-02-28 5:46 UTC (permalink / raw) To: u-boot From: Macpaul Lin <macpaul@andestech.com> Add lowlevel ag102 soc support. Signed-off-by: Macpaul Lin <macpaul@andestech.com> --- Changes for v2: - cpu.c: - 1. Remove unused variables. - 2. Replace while(1) in do_reset by hang(). - 3. Clean up other coding styles. - timer.c: remove unneccessary static declaration Changes for v3: - watchdog.S: add support macro in linkage.h arch/nds32/cpu/n1213/ag102/Makefile | 58 ++++++ arch/nds32/cpu/n1213/ag102/cpu.c | 195 ++++++++++++++++++ arch/nds32/cpu/n1213/ag102/lowlevel_init.S | 297 ++++++++++++++++++++++++++++ arch/nds32/cpu/n1213/ag102/timer.c | 205 +++++++++++++++++++ arch/nds32/cpu/n1213/ag102/watchdog.S | 49 +++++ 5 files changed, 804 insertions(+), 0 deletions(-) create mode 100644 arch/nds32/cpu/n1213/ag102/Makefile create mode 100644 arch/nds32/cpu/n1213/ag102/cpu.c create mode 100644 arch/nds32/cpu/n1213/ag102/lowlevel_init.S create mode 100644 arch/nds32/cpu/n1213/ag102/timer.c create mode 100644 arch/nds32/cpu/n1213/ag102/watchdog.S diff --git a/arch/nds32/cpu/n1213/ag102/Makefile b/arch/nds32/cpu/n1213/ag102/Makefile new file mode 100644 index 0000000..8716c4e --- /dev/null +++ b/arch/nds32/cpu/n1213/ag102/Makefile @@ -0,0 +1,58 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Written-by: Prafulla Wadaskar <prafulla@marvell.com> +# +# Copyright (C) 2011 Andes Technology Corporation +# Shawn Lin, Andes Technology Corporation <nobuhiro@andestech.com> +# Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(SOC).o + +COBJS-y := cpu.o timer.o + +ifndef CONFIG_SKIP_LOWLEVEL_INIT +SOBJS := lowlevel_init.o +endif + +ifndef CONFIG_SKIP_TRUNOFF_WATCHDOG +SOBJS += watchdog.o +endif + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS-y)) + +all: $(obj).depend $(LIB) + +$(LIB): $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/arch/nds32/cpu/n1213/ag102/cpu.c b/arch/nds32/cpu/n1213/ag102/cpu.c new file mode 100644 index 0000000..ed88b52 --- /dev/null +++ b/arch/nds32/cpu/n1213/ag102/cpu.c @@ -0,0 +1,195 @@ +/* + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH <www.elinos.com> + * Marius Groeger <mgroeger@sysgo.de> + * + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, <gj@denx.de> + * + * Copyright (C) 2011 Andes Technology Corporation + * Shawn Lin, Andes Technology Corporation <nobuhiro@andestech.com> + * Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* CPU specific code */ +#include <common.h> +#include <command.h> +#include <watchdog.h> +#include <asm/cache.h> + +#include <faraday/ftwdt010_wdt.h> + +/* + * cleanup_before_linux() is called just before we call linux + * it prepares the processor for linux + * + * we disable interrupt and caches. + */ +int cleanup_before_linux(void) +{ + disable_interrupts(); + +#ifdef CONFIG_MMU + /* turn off I/D-cache */ + icache_disable(); + dcache_disable(); + + /* flush I/D-cache */ + invalidate_icac(); + invalidate_dcac(); +#endif + + return 0; +} + +int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + disable_interrupts(); + + /* + * reset to the base addr of andesboot. + * currently no ROM loader at addr 0. + * do not use reset_cpu(0); + */ +#ifdef CONFIG_FTWDT010_WATCHDOG + /* + * workaround: if we use CONFIG_HW_WATCHDOG with ftwdt010, will lead + * automatic hardware reset when booting Linux. + * Please do not use CONFIG_HW_WATCHDOG and WATCHDOG_RESET() here. + */ + ftwdt010_wdt_reset(); +#endif /* CONFIG_FTWDT010_WATCHDOG */ + hang(); + + /*NOTREACHED*/ +} + +static inline unsigned long CACHE_LINE_SIZE(enum cache_t cache) +{ + if (cache == ICACHE) + return 8 << (((GET_ICM_CFG() & ICM_CFG_MSK_ISZ) \ + >> ICM_CFG_OFF_ISZ) - 1); + else + return 8 << (((GET_DCM_CFG() & DCM_CFG_MSK_DSZ) \ + >> DCM_CFG_OFF_DSZ) - 1); +} + +void dcache_flush_range(unsigned long start, unsigned long end) +{ + unsigned long line_size; + + line_size = CACHE_LINE_SIZE(DCACHE); + + while (end > start) { + __asm__ volatile ("\n\tcctl %0, L1D_VA_WB" : : "r"(start)); + __asm__ volatile ("\n\tcctl %0, L1D_VA_INVAL" : : "r"(start)); + start += line_size; + } +} + +void icache_inval_range(unsigned long start, unsigned long end) +{ + unsigned long line_size; + + line_size = CACHE_LINE_SIZE(ICACHE); + while (end > start) { + __asm__ volatile ("\n\tcctl %0, L1I_VA_INVAL" : : "r"(start)); + start += line_size; + } +} + +void flush_cache(unsigned long addr, unsigned long size) +{ + dcache_flush_range(addr, addr + size); + icache_inval_range(addr, addr + size); +} + +void icache_enable(void) +{ + __asm__ __volatile__ ( + "mfsr $p0, $mr8\n\t" + "ori $p0, $p0, 0x01\n\t" + "mtsr $p0, $mr8\n\t" + "isb\n\t" + ); +} + +void icache_disable(void) +{ + __asm__ __volatile__ ( + "mfsr $p0, $mr8\n\t" + "li $p1, ~0x01\n\t" + "and $p0, $p0, $p1\n\t" + "mtsr $p0, $mr8\n\t" + "isb\n\t" + ); +} + +int icache_status(void) +{ + int ret; + + __asm__ __volatile__ ( + "mfsr $p0, $mr8\n\t" + "andi %0, $p0, 0x01\n\t" + : "=r" (ret) + : + : "memory" + ); + + return ret; +} + +void dcache_enable(void) +{ + __asm__ __volatile__ ( + "mfsr $p0, $mr8\n\t" + "ori $p0, $p0, 0x02\n\t" + "mtsr $p0, $mr8\n\t" + "isb\n\t" + ); +} + +void dcache_disable(void) +{ + __asm__ __volatile__ ( + "mfsr $p0, $mr8\n\t" + "li $p1, ~0x02\n\t" + "and $p0, $p0, $p1\n\t" + "mtsr $p0, $mr8\n\t" + "isb\n\t" + ); +} + +int dcache_status(void) +{ + int ret; + + __asm__ __volatile__ ( + "mfsr $p0, $mr8\n\t" + "andi %0, $p0, 0x02\n\t" + : "=r" (ret) + : + : "memory" + ); + + return ret; +} diff --git a/arch/nds32/cpu/n1213/ag102/lowlevel_init.S b/arch/nds32/cpu/n1213/ag102/lowlevel_init.S new file mode 100644 index 0000000..d842afa --- /dev/null +++ b/arch/nds32/cpu/n1213/ag102/lowlevel_init.S @@ -0,0 +1,297 @@ +/* + * Copyright (C) 2011 Andes Technology Corporation + * Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +.text + +#include <common.h> +#include <config.h> + +#include <asm/macro.h> +#include <generated/asm-offsets.h> + +/* + * parameters for Synopsys DWC DDR2/DDR1 Memory Controller + */ +#define DDR2C_BASE_A (CONFIG_DWCDDR21MCTL_BASE) +#define DDR2C_CCR_A (DDR2C_BASE_A + DWCDDR21MCTL_CCR) +#define DDR2C_DCR_A (DDR2C_BASE_A + DWCDDR21MCTL_DCR) +#define DDR2C_IOCR_A (DDR2C_BASE_A + DWCDDR21MCTL_IOCR) +#define DDR2C_CSR_A (DDR2C_BASE_A + DWCDDR21MCTL_CSR) +#define DDR2C_DRR_A (DDR2C_BASE_A + DWCDDR21MCTL_DRR) +#define DDR2C_DLLCR0_A (DDR2C_BASE_A + DWCDDR21MCTL_DLLCR0) +#define DDR2C_DLLCR1_A (DDR2C_BASE_A + DWCDDR21MCTL_DLLCR1) +#define DDR2C_DLLCR2_A (DDR2C_BASE_A + DWCDDR21MCTL_DLLCR2) +#define DDR2C_DLLCR3_A (DDR2C_BASE_A + DWCDDR21MCTL_DLLCR3) +#define DDR2C_DLLCR4_A (DDR2C_BASE_A + DWCDDR21MCTL_DLLCR4) +#define DDR2C_DLLCR5_A (DDR2C_BASE_A + DWCDDR21MCTL_DLLCR5) +#define DDR2C_DLLCR6_A (DDR2C_BASE_A + DWCDDR21MCTL_DLLCR6) +#define DDR2C_DLLCR7_A (DDR2C_BASE_A + DWCDDR21MCTL_DLLCR7) +#define DDR2C_DLLCR8_A (DDR2C_BASE_A + DWCDDR21MCTL_DLLCR8) +#define DDR2C_DLLCR9_A (DDR2C_BASE_A + DWCDDR21MCTL_DLLCR9) +#define DDR2C_RSLR0_A (DDR2C_BASE_A + DWCDDR21MCTL_RSLR0) +#define DDR2C_RDGR0_A (DDR2C_BASE_A + DWCDDR21MCTL_RDGR0) +#define DDR2C_DTAR_A (DDR2C_BASE_A + DWCDDR21MCTL_DTAR) +#define DDR2C_MR_A (DDR2C_BASE_A + DWCDDR21MCTL_MR) + +#define DDR2C_CCR_D CONFIG_SYS_DWCDDR21MCTL_CCR +#define DDR2C_CCR_D2 CONFIG_SYS_DWCDDR21MCTL_CCR2 +#define DDR2C_DCR_D CONFIG_SYS_DWCDDR21MCTL_DCR +#define DDR2C_IOCR_D CONFIG_SYS_DWCDDR21MCTL_IOCR +#define DDR2C_CSR_D CONFIG_SYS_DWCDDR21MCTL_CSR +#define DDR2C_DRR_D CONFIG_SYS_DWCDDR21MCTL_DRR +#define DDR2C_RSLR0_D CONFIG_SYS_DWCDDR21MCTL_RSLR0 +#define DDR2C_RDGR0_D CONFIG_SYS_DWCDDR21MCTL_RDGR0 +#define DDR2C_DTAR_D CONFIG_SYS_DWCDDR21MCTL_DTAR +#define DDR2C_MR_D CONFIG_SYS_DWCDDR21MCTL_MR + +#define DDR2C_DLLCR0_D CONFIG_SYS_DWCDDR21MCTL_DLLCR0 /* 0-9 are same */ + +/* + * parameters for the ahbc controller + */ +#define AHBC_CR_A (CONFIG_FTAHBC020S_BASE + FTAHBC020S_CR) +#define AHBC_BSR6_A (CONFIG_FTAHBC020S_BASE + FTAHBC020S_SLAVE_BSR_6) + +#define AHBC_BSR6_D CONFIG_SYS_FTAHBC020S_SLAVE_BSR_6 + +/* + * parameters for the ANDES PCU controller + */ +#define PCU_PCS4_A (CONFIG_ANDES_PCU_BASE + ANDES_PCU_PCS4) +#define PCU_PCS4_D CONFIG_SYS_ANDES_CPU_PCS4 + +/* + * numeric 7 segment display + */ +.macro led, num + write32 CONFIG_DEBUG_LED, \num +.endm + +/* + * Waiting for SDRAM to set up + */ +/* +.macro wait_sdram + li $r0, DDR2C_CSR_A +1: + lwi $r1, [$r0+FTSDMC021_CR2] + bnez $r1, 1b +.endm +*/ + +#ifndef CONFIG_SKIP_LOWLEVEL_INIT +.globl lowlevel_init +lowlevel_init: + move $r10, $lp + + /* U200 */ +! led 0x00 +! jal scale_to_500mhz + + led 0x10 + jal mem_init + + led 0x20 + jal remap + + led 0x30 + ret $r10 + +scale_to_500mhz: + move $r11, $lp + + /* + * scale to 500Mhz + */ + led 0x01 + write32 PCU_PCS4_A, 0x1102000f ! save data to PCS4 + + move $lp, $r11 + ret + +mem_init: + move $r11, $lp + + /* + * config AHB Controller + */ + led 0x12 + write32 AHBC_BSR6_A, AHBC_BSR6_D + + /* + * config Synopsys DWC DDR2/DDR1 Memory Controller + */ +ddr2c_init: +set_dcr: + led 0x14 + write32 DDR2C_DCR_A, DDR2C_DCR_D ! 0x000020d4 + +auto_sizing: + /* + * ebios: $r10->$r7, $r11->$r8, $r12->$r9, $r13->$r12, $r14->$r13 + */ +set_iocr: + led 0x19 + write32 DDR2C_IOCR_A, DDR2C_IOCR_D +set_drr: + led 0x16 + write32 DDR2C_DRR_A, DDR2C_DRR_D ! 0x00034812 +set_dllcr: + led 0x18 + write32 DDR2C_DLLCR0_A, DDR2C_DLLCR0_D + write32 DDR2C_DLLCR1_A, DDR2C_DLLCR0_D + write32 DDR2C_DLLCR2_A, DDR2C_DLLCR0_D + write32 DDR2C_DLLCR3_A, DDR2C_DLLCR0_D + write32 DDR2C_DLLCR4_A, DDR2C_DLLCR0_D + write32 DDR2C_DLLCR5_A, DDR2C_DLLCR0_D + write32 DDR2C_DLLCR6_A, DDR2C_DLLCR0_D + write32 DDR2C_DLLCR7_A, DDR2C_DLLCR0_D + write32 DDR2C_DLLCR8_A, DDR2C_DLLCR0_D + write32 DDR2C_DLLCR9_A, DDR2C_DLLCR0_D +set_rslr0: + write32 DDR2C_RSLR0_A, DDR2C_RSLR0_D ! 0x00000040 +set_rdgr0: + write32 DDR2C_RDGR0_A, DDR2C_RDGR0_D ! 0x000055cf +set_dtar: + led 0x15 + write32 DDR2C_DTAR_A, DDR2C_DTAR_D ! 0x00100000 +set_mode: + led 0x17 + write32 DDR2C_MR_A, DDR2C_MR_D ! 0x00000852 +set_ccr: + write32 DDR2C_CCR_A, DDR2C_CCR_D + +#ifdef TRIGGER_INIT: +trigger_init: + write32 DDR2C_CCR_A, DDR2C_CCR_D ! 0x80020000 + + /* Wait for ddr init state to be set */ + msync ALL + isb + + /* Wait until the config initialization is finish */ +1: + la $r4, DDR2C_CSR_A + lwi $r5, [$r4] + srli $r5, $r5, 23 + bnez $r5, 1b +#endif + +data_training: +! write32 DDR2C_CCR_A, DDR2C_CCR_D2 ! 0x40020004 + + /* Wait for ddr init state to be set */ + msync ALL + isb + + /* wait until the ddr data trainning is complete */ +1: + la $r4, DDR2C_CSR_A + lwi $r5, [$r4] + srli $r6, $r5, 23 + bnez $r6, 1b + + lwi $r1, [$r4] + srli $r6, $r5, 20 + li $r5, 0x00ffffff + swi $r1, [$r4] + bnez $r6, ddr2c_init + + led 0x1a + move $lp, $r11 + ret + +remap: + move $r11, $lp +#ifdef __NDS32_N1213_43U1H__ /* NDS32 V0 ISA - AG101 Only */ + bal 2f +relo_base: + move $r0, $lp +#else +relo_base: + mfusr $r0, $pc +#endif /* __NDS32_N1213_43U1H__ */ + + /* + * Remapping + */ +#ifdef CONFIG_MEM_REMAP + /* + * Copy ROM code to SDRAM base for memory remap layout. + * This is not the real relocation, the real relocation is the function + * relocate_code() is start.S which supports the systems is memory + * remapped or not. + */ + /* + * Doing memory remap is essential for preparing some non-OS or RTOS + * applications. + * + * This is also a must on ADP-AG101 board. + * The reason is because the ROM/FLASH circuit on PCB board. + * AG101-A0 board has 2 jumpers MA17 and SW5 to configure which + * ROM/FLASH is used to boot. + * + * When SW5 = "0101", MA17 = LO, the ROM is connected to BANK0, + * and the FLASH is connected to BANK1. + * When SW5 = "1010", MA17 = HI, the ROM is disabled (still at BANK0), + * and the FLASH is connected to BANK0. + * It will occur problem when doing flash probing if the flash is at + * BANK0 (0x00000000) while memory remapping was skipped. + * + * Other board like ADP-AG101P may not enable this since there is only + * a FLASH connected to bank0. + */ + led 0x21 + li $r4, PHYS_SDRAM_0_AT_INIT /* 0x10000000 */ + li $r5, 0x0 + la $r1, relo_base /* get $pc or $lp */ + sub $r2, $r0, $r1 + sethi $r6, hi20(_end) + ori $r6, $r6, lo12(_end) + add $r6, $r6, $r2 +1: + lwi.p $r7, [$r5], #4 + swi.p $r7, [$r4], #4 + blt $r5, $r6, 1b + + /* set remap bit */ + /* + * MEM remap bit is operational + * - use it to map writeable memory at 0x00000000, in place of flash + * - before remap: flash/rom 0x00000000, sdram: 0x10000000-0x4fffffff + * - after remap: flash/rom 0x80000000, sdram: 0x00000000 + */ + led 0x2c + setbf15 AHBC_CR_A, FTAHBC020S_CR_REMAP ! 0x1 + +#endif /* #ifdef CONFIG_MEM_REMAP */ + move $lp, $r11 +2: + ret + +.globl show_led +show_led: + li $r8, (CONFIG_DEBUG_LED) + swi $r7, [$r8] + ret +#endif /* #ifndef CONFIG_SKIP_LOWLEVEL_INIT */ diff --git a/arch/nds32/cpu/n1213/ag102/timer.c b/arch/nds32/cpu/n1213/ag102/timer.c new file mode 100644 index 0000000..caa36b8 --- /dev/null +++ b/arch/nds32/cpu/n1213/ag102/timer.c @@ -0,0 +1,205 @@ +/* + * (C) Copyright 2009 Faraday Technology + * Po-Yu Chuang <ratbert@faraday-tech.com> + * + * Copyright (C) 2011 Andes Technology Corporation + * Shawn Lin, Andes Technology Corporation <nobuhiro@andestech.com> + * Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <common.h> +#include <asm/io.h> +#include <faraday/fttmr010.h> + +static ulong timestamp; +static ulong lastdec; + +int timer_init(void) +{ + struct fttmr010 *tmr = (struct fttmr010 *)CONFIG_FTTMR010_BASE; + unsigned int cr; + + debug("%s()\n", __func__); + + /* disable timers */ + writel(0, &tmr->cr); + +#ifdef CONFIG_FTTMR010_EXT_CLK + /* use 32768Hz oscillator for RTC, WDT, TIMER */ + ftpmu010_32768osc_enable(); +#endif + + /* setup timer */ + writel(TIMER_LOAD_VAL, &tmr->timer3_load); + writel(TIMER_LOAD_VAL, &tmr->timer3_counter); + writel(0, &tmr->timer3_match1); + writel(0, &tmr->timer3_match2); + + /* we don't want timer to issue interrupts */ + writel(FTTMR010_TM3_MATCH1 | + FTTMR010_TM3_MATCH2 | + FTTMR010_TM3_OVERFLOW, + &tmr->interrupt_mask); + + cr = readl(&tmr->cr); +#ifdef CONFIG_FTTMR010_EXT_CLK + cr |= FTTMR010_TM3_CLOCK; /* use external clock */ +#endif + cr |= FTTMR010_TM3_ENABLE; + writel(cr, &tmr->cr); + + /* init the timestamp and lastdec value */ + reset_timer_masked(); + + return 0; +} + +/* + * timer without interrupts + */ + +/* + * reset time + */ +void reset_timer_masked(void) +{ + struct fttmr010 *tmr = (struct fttmr010 *)CONFIG_FTTMR010_BASE; + + /* capure current decrementer value time */ +#ifdef CONFIG_FTTMR010_EXT_CLK + lastdec = readl(&tmr->timer3_counter) / (TIMER_CLOCK / CONFIG_SYS_HZ); +#else + lastdec = readl(&tmr->timer3_counter) / (CONFIG_SYS_CLK_FREQ / 2); +#endif + timestamp = 0; /* start "advancing" time stamp from 0 */ + + debug("%s(): lastdec = %lx\n", __func__, lastdec); +} + +void reset_timer(void) +{ + debug("%s()\n", __func__); + reset_timer_masked(); +} + +/* + * return timer ticks + */ +ulong get_timer_masked(void) +{ + struct fttmr010 *tmr = (struct fttmr010 *)CONFIG_FTTMR010_BASE; + + /* current tick value */ +#ifdef CONFIG_FTTMR010_EXT_CLK + ulong now = readl(&tmr->timer3_counter) / (TIMER_CLOCK / CONFIG_SYS_HZ); +#else + ulong now = readl(&tmr->timer3_counter) / \ + (CONFIG_SYS_CLK_FREQ / 2 / 1024); +#endif + + debug("%s(): now = %lx, lastdec = %lx\n", __func__, now, lastdec); + + if (lastdec >= now) { + /* + * normal mode (non roll) + * move stamp fordward with absoulte diff ticks + */ + timestamp += lastdec - now; + } else { + /* + * we have overflow of the count down timer + * + * nts = ts + ld + (TLV - now) + * ts=old stamp, ld=time that passed before passing through -1 + * (TLV-now) amount of time after passing though -1 + * nts = new "advancing time stamp"...it could also roll and + * cause problems. + */ + timestamp += lastdec + TIMER_LOAD_VAL - now; + } + + lastdec = now; + + debug("%s() returns %lx\n", __func__, timestamp); + + return timestamp; +} + +/* + * return difference between timer ticks and base + */ +ulong get_timer(ulong base) +{ + debug("%s(%lx)\n", __func__, base); + return get_timer_masked() - base; +} + +void set_timer(ulong t) +{ + debug("%s(%lx)\n", __func__, t); + timestamp = t; +} + +/* delay x useconds AND preserve advance timestamp value */ +void __udelay(unsigned long usec) +{ + struct fttmr010 *tmr = (struct fttmr010 *)CONFIG_FTTMR010_BASE; + +#ifdef CONFIG_FTTMR010_EXT_CLK + long tmo = usec * (TIMER_CLOCK / 1000) / 1000; +#else + long tmo = usec * ((CONFIG_SYS_CLK_FREQ / 2) / 1000) / 1000; +#endif + unsigned long now, last = readl(&tmr->timer3_counter); + + debug("%s(%lu)\n", __func__, usec); + while (tmo > 0) { + now = readl(&tmr->timer3_counter); + if (now > last) /* count down timer overflow */ + tmo -= TIMER_LOAD_VAL + last - now; + else + tmo -= last - now; + last = now; + } +} + +/* + * This function is derived from PowerPC code (read timebase as long long). + * On ARM it just returns the timer value. + */ +unsigned long long get_ticks(void) +{ + debug("%s()\n", __func__); + return get_timer(0); +} + +/* + * This function is derived from PowerPC code (timebase clock frequency). + * On ARM it returns the number of timer ticks per second. + */ +ulong get_tbclk(void) +{ + debug("%s()\n", __func__); +#ifdef CONFIG_FTTMR010_EXT_CLK + return CONFIG_SYS_HZ; +#else + return CONFIG_SYS_CLK_FREQ; +#endif +} diff --git a/arch/nds32/cpu/n1213/ag102/watchdog.S b/arch/nds32/cpu/n1213/ag102/watchdog.S new file mode 100644 index 0000000..56cecda --- /dev/null +++ b/arch/nds32/cpu/n1213/ag102/watchdog.S @@ -0,0 +1,49 @@ +/* + * Copyright (C) 2011 Andes Technology Corporation + * Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <asm/arch-ag102/ag102.h> +#include <linux/linkage.h> + +.text + +#ifndef CONFIG_SKIP_TRUNOFF_WATCHDOG +ENTRY(turnoff_watchdog) + +#define WD_CR 0xC +#define WD_ENABLE 0x1 + + ! Turn off the watchdog, according to Faraday FTWDT010 spec + li $p0, (CONFIG_FTWDT010_BASE+WD_CR) ! Get the addr of WD CR + lwi $p1, [$p0] ! Get the config of WD + andi $p1, $p1, 0x1f ! Wipe out useless bits + li $r0, ~WD_ENABLE + and $p1, $p1, $r0 ! Set WD disable + sw $p1, [$p0] ! Write back to WD CR + + ! Disable Interrupts by clear GIE in $PSW reg + setgie.d + + ret + +ENDPROC(turnoff_watchdog) +#endif -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v3 2/4] nds32/ag102: add ag102 soc support 2012-02-28 5:46 ` [U-Boot] [PATCH v3 2/4] nds32/ag102: add ag102 soc support Macpaul Lin @ 2012-04-22 8:55 ` Macpaul Lin 0 siblings, 0 replies; 8+ messages in thread From: Macpaul Lin @ 2012-04-22 8:55 UTC (permalink / raw) To: u-boot Hi Macpaul, 2012/2/28 Macpaul Lin <macpaul@gmail.com>: > From: Macpaul Lin <macpaul@andestech.com> > > Add lowlevel ag102 soc support. > > Signed-off-by: Macpaul Lin <macpaul@andestech.com> > --- > Changes for v2: > ?- cpu.c: > ? - 1. Remove unused variables. > ? - 2. Replace while(1) in do_reset by hang(). > ? - 3. Clean up other coding styles. > ?- timer.c: remove unneccessary static declaration > Changes for v3: > ?- watchdog.S: add support macro in linkage.h > Applied to u-boot-nds32/master, Thanks. -- Best regards, Macpaul Lin ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v3 3/4] board/adp-ag102: add board specific files 2012-02-28 5:46 ` [U-Boot] [PATCH v3 1/4] nds32/ag102: add header support of ag102 soc Macpaul Lin 2012-02-28 5:46 ` [U-Boot] [PATCH v3 2/4] nds32/ag102: add ag102 soc support Macpaul Lin @ 2012-02-28 5:46 ` Macpaul Lin 2012-04-22 8:52 ` Macpaul Lin 2012-02-28 5:46 ` [U-Boot] [PATCH v3 4/4] board/adp-ag102: add configuration of adp-ag102 Macpaul Lin 2012-04-22 8:54 ` [U-Boot] [PATCH v3 1/4] nds32/ag102: add header support of ag102 soc Macpaul Lin 3 siblings, 1 reply; 8+ messages in thread From: Macpaul Lin @ 2012-02-28 5:46 UTC (permalink / raw) To: u-boot From: Macpaul Lin <macpaul@andestech.com> Add board specific files. Signed-off-by: Macpaul Lin <macpaul@andestech.com> --- Changes for v2-v3: - No change. board/AndesTech/adp-ag102/Makefile | 43 +++++++++++++ board/AndesTech/adp-ag102/adp-ag102.c | 107 +++++++++++++++++++++++++++++++++ 2 files changed, 150 insertions(+), 0 deletions(-) create mode 100644 board/AndesTech/adp-ag102/Makefile create mode 100644 board/AndesTech/adp-ag102/adp-ag102.c diff --git a/board/AndesTech/adp-ag102/Makefile b/board/AndesTech/adp-ag102/Makefile new file mode 100644 index 0000000..1cbf2d4 --- /dev/null +++ b/board/AndesTech/adp-ag102/Makefile @@ -0,0 +1,43 @@ +# +# Copyright (C) 2011 Andes Technology Corporation +# Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := adp-ag102.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS)) + +$(LIB): $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/AndesTech/adp-ag102/adp-ag102.c b/board/AndesTech/adp-ag102/adp-ag102.c new file mode 100644 index 0000000..5a25632 --- /dev/null +++ b/board/AndesTech/adp-ag102/adp-ag102.c @@ -0,0 +1,107 @@ +/* + * Copyright (C) 2011 Andes Technology Corporation + * Shawn Lin, Andes Technology Corporation <nobuhiro@andestech.com> + * Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <common.h> +#include <netdev.h> +#include <asm/io.h> + +#include <faraday/ftsdc010.h> +#ifdef CONFIG_FTSMC020 +#include <faraday/ftsmc020.h> +#endif + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Miscellaneous platform dependent initializations + */ + +int board_init(void) +{ + /* + * refer to BOOT_PARAMETER_PA_BASE within + * "linux/arch/nds32/include/asm/misc_spec.h" + */ + gd->bd->bi_arch_number = MACH_TYPE_ADPAG102; + gd->bd->bi_boot_params = PHYS_SDRAM_0 + 0x400; + +#if !defined(CONFIG_SYS_NO_FLASH) + ftsmc020_init(); /* initialize Flash */ +#endif /* CONFIG_SYS_NO_FLASH */ + return 0; +} + +int dram_init(void) +{ + unsigned long sdram_base = PHYS_SDRAM_0; + unsigned long expected_size = PHYS_SDRAM_0_SIZE; + unsigned long actual_size; + + actual_size = get_ram_size((void *)sdram_base, expected_size); + + gd->ram_size = actual_size; + + if (expected_size != actual_size) { + printf("Warning: Only %lu of %lu MiB SDRAM is working\n", + actual_size >> 20, expected_size >> 20); + } + + return 0; +} + +int board_eth_init(bd_t *bd) +{ + return ftgmac100_initialize(bd); +} + +#if !defined(CONFIG_SYS_NO_FLASH) +ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info) +{ + if (banknum == 0) { /* non-CFI boot flash */ + info->portwidth = FLASH_CFI_8BIT; + info->chipwidth = FLASH_CFI_BY8; + info->interface = FLASH_CFI_X8; + return 1; + } else { + return 0; + } +} +#endif /* CONFIG_SYS_NO_FLASH */ + +#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI) +void pci_init_board(void) +{ + /* should be pci_ftpci100_init() */ + extern void pci_ftpci_init(); + + pci_ftpci_init(); +} +#endif + +#ifdef CONFIG_GENERIC_MMC +int board_mmc_init(bd_t *bis) +{ + ftsdc010_mmc_init(0); + return 0; +} +#endif -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v3 3/4] board/adp-ag102: add board specific files 2012-02-28 5:46 ` [U-Boot] [PATCH v3 3/4] board/adp-ag102: add board specific files Macpaul Lin @ 2012-04-22 8:52 ` Macpaul Lin 0 siblings, 0 replies; 8+ messages in thread From: Macpaul Lin @ 2012-04-22 8:52 UTC (permalink / raw) To: u-boot Hi Macpaul, 2012/2/28 Macpaul Lin <macpaul@gmail.com> > > From: Macpaul Lin <macpaul@andestech.com> > > Add board specific files. > > Signed-off-by: Macpaul Lin <macpaul@andestech.com> > --- > Changes for v2-v3: > ?- No change. > > ?board/AndesTech/adp-ag102/Makefile ? ?| ? 43 +++++++++++++ > ?board/AndesTech/adp-ag102/adp-ag102.c | ?107 +++++++++++++++++++++++++++++++++ > ?2 files changed, 150 insertions(+), 0 deletions(-) > ?create mode 100644 board/AndesTech/adp-ag102/Makefile > ?create mode 100644 board/AndesTech/adp-ag102/adp-ag102.c > > diff --git a/board/AndesTech/adp-ag102/Makefile b/board/AndesTech/adp-ag102/Makefile Applied to u-boot-nds32/master, Thanks. -- Best regards, Macpaul Lin ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v3 4/4] board/adp-ag102: add configuration of adp-ag102 2012-02-28 5:46 ` [U-Boot] [PATCH v3 1/4] nds32/ag102: add header support of ag102 soc Macpaul Lin 2012-02-28 5:46 ` [U-Boot] [PATCH v3 2/4] nds32/ag102: add ag102 soc support Macpaul Lin 2012-02-28 5:46 ` [U-Boot] [PATCH v3 3/4] board/adp-ag102: add board specific files Macpaul Lin @ 2012-02-28 5:46 ` Macpaul Lin 2012-04-22 8:52 ` Macpaul Lin 2012-04-22 8:54 ` [U-Boot] [PATCH v3 1/4] nds32/ag102: add header support of ag102 soc Macpaul Lin 3 siblings, 1 reply; 8+ messages in thread From: Macpaul Lin @ 2012-02-28 5:46 UTC (permalink / raw) To: u-boot From: Macpaul Lin <macpaul@andestech.com> board: Add config file of board adp-ag102 Add adp-ag102 into boards.cfg Add adp-ag102 into MAINTAINERS doc: add README of ag102 Signed-off-by: Macpaul Lin <macpaul@andestech.com> --- Changes for v2: - add pci and usb support to board setting adp-ag102.h Changes for v3: - Fix patch because update of boards.cfg and MAINTAINERS MAINTAINERS | 1 + boards.cfg | 1 + doc/README.ag102 | 36 ++++ include/configs/adp-ag102.h | 375 +++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 413 insertions(+), 0 deletions(-) create mode 100644 doc/README.ag102 create mode 100644 include/configs/adp-ag102.h diff --git a/MAINTAINERS b/MAINTAINERS index 1e40af2..5b45978 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1199,6 +1199,7 @@ Macpaul Lin <macpaul@andestech.com> ADP-AG101 N1213 (AG101 SoC) ADP-AG101P N1213 (AG101P XC5 FPGA) + ADP-AG102 N1213f (AG102 SoC with FPU) ######################################################################### # OpenRISC Systems: # diff --git a/boards.cfg b/boards.cfg index 05ce1ae..38f0d34 100644 --- a/boards.cfg +++ b/boards.cfg @@ -376,6 +376,7 @@ incaip_150MHz mips mips32 incaip - qi_lb60 mips xburst qi_lb60 qi adp-ag101 nds32 n1213 adp-ag101 AndesTech ag101 adp-ag101p nds32 n1213 adp-ag101p AndesTech ag101 +adp-ag102 nds32 n1213 adp-ag102 AndesTech ag102 nios2-generic nios2 nios2 nios2-generic altera PCI5441 nios2 nios2 pci5441 psyent PK1C20 nios2 nios2 pk1c20 psyent diff --git a/doc/README.ag102 b/doc/README.ag102 new file mode 100644 index 0000000..7d142a7 --- /dev/null +++ b/doc/README.ag102 @@ -0,0 +1,36 @@ +Andes Technology SoC AG102 +========================== + +AG102 is the second SoC produced by Andes Technology using N1213 CPU core +with FPU and DDR contoller support. +AG102 has integrated both AHB and APB bus and many periphals for application +and product development. + +ADP-AG102 +========= + +ADP-AG102 is the SoC with AG102 hardcore CPU. + +Configurations +============== + +CONFIG_MEM_REMAP: + Doing memory remap is essential for preparing some non-OS or RTOS + applications. + +CONFIG_SKIP_LOWLEVEL_INIT: + If you want to boot this system from SPI ROM and bypass e-bios (the + other boot loader on ROM). You should undefine CONFIG_SKIP_LOWLEVEL_INIT + in "include/configs/adp-ag102.h". + +Build and boot steps +==================== + +build: +1. Prepare the toolchains and make sure the $PATH to toolchains is correct. +2. Use `make adp-ag102` in u-boot root to build the image. + +Burn u-boot to SPI ROM: +==================== + +This section will be added later. diff --git a/include/configs/adp-ag102.h b/include/configs/adp-ag102.h new file mode 100644 index 0000000..a4628e4 --- /dev/null +++ b/include/configs/adp-ag102.h @@ -0,0 +1,375 @@ +/* + * Copyright (C) 2011 Andes Technology Corporation + * Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/arch/ag102.h> + +/* + * CPU and Board Configuration Options + */ +#define CONFIG_ADP_AG102 + +#define CONFIG_USE_INTERRUPT + +#define CONFIG_SKIP_LOWLEVEL_INIT + +#ifndef CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_MEM_REMAP +#endif + +#ifdef CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SYS_TEXT_BASE 0x04200000 +#else +#define CONFIG_SYS_TEXT_BASE 0x00000000 +#endif + +/* + * Timer + */ + +/* + * According to the discussion in u-boot mailing list before, + * CONFIG_SYS_HZ at 1000 is mandatory. + */ +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_CLK_FREQ (66000000 * 2) +#define VERSION_CLOCK CONFIG_SYS_CLK_FREQ + +/* + * Use Externel CLOCK or PCLK + */ +#undef CONFIG_FTRTC010_EXTCLK + +#ifndef CONFIG_FTRTC010_EXTCLK +#define CONFIG_FTRTC010_PCLK +#endif + +#ifdef CONFIG_FTRTC010_EXTCLK +#define TIMER_CLOCK 32768 /* CONFIG_FTRTC010_EXTCLK */ +#else +#define TIMER_CLOCK CONFIG_SYS_HZ /* CONFIG_FTRTC010_PCLK */ +#endif + +#define TIMER_LOAD_VAL 0xffffffff + +/* + * Real Time Clock + */ +#define CONFIG_RTC_FTRTC010 + +/* + * Real Time Clock Divider + * RTC_DIV_COUNT (OSC_CLK/OSC_5MHZ) + */ +#define OSC_5MHZ (5*1000000) +#define OSC_CLK (2*OSC_5MHZ) +#define RTC_DIV_COUNT (OSC_CLK/OSC_5MHZ) + +/* + * Serial console configuration + */ + +/* FTUART is a high speed NS 16C550A compatible UART */ +#define CONFIG_BAUDRATE 38400 +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_COM1 CONFIG_FTUART010_01_BASE +#define CONFIG_SYS_NS16550_REG_SIZE -4 +#define CONFIG_SYS_NS16550_CLK 33000000 /* AG102 */ + +/* valid baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Ethernet + */ +#define CONFIG_NET_MULTI +#define CONFIG_PHY_MAX_ADDR 32 /* this comes from <linux/phy.h> */ +#define CONFIG_SYS_DISCOVER_PHY +#define CONFIG_FTGMAC100 +#define CONFIG_FTGMAC100_EGIGA + +#define CONFIG_BOOTDELAY 3 + +/* + * SD (MMC) controller + */ +#define CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_DOS_PARTITION +#define CONFIG_FTSDC010 +#define CONFIG_FTSDC010_NUMBER 1 +#define CONFIG_FTSDC010_SDIO +#define CONFIG_CMD_FAT +#define CONFIG_CMD_EXT2 + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DATE +#define CONFIG_CMD_PING +#define CONFIG_CMD_IDE +#define CONFIG_CMD_FAT +#define CONFIG_CMD_ELF + +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS + +/* + * PCI + */ +#define CONFIG_PCI +#define CONFIG_FTPCI100 +#define CONFIG_FTPCI100_MEM_BASE 0xa0000000 +#define CONFIG_FTPCI100_IO_SIZE FTPCI100_BASE_IO_SIZE(256) /* 256M */ +#define CONFIG_FTPCI100_MEM_SIZE FTPCI100_MEM_SIZE(128) /* 128M */ +#define CONFIG_FTPCI100_MEM_BASE_SIZE1 0x50 + +#define CONFIG_PCI_MEM_BUS 0xa0000000 +#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS +#define CONFIG_PCI_MEM_SIZE 0x01000000 /* 256M */ + +#define CONFIG_PCI_IO_BUS 0x90000000 +#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS +#define CONFIG_PCI_IO_SIZE 0x00100000 /* 1M */ + +/* + * USB + */ +#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI) +#if defined(CONFIG_FTPCI100) +#define __io /* enable outl & inl */ +#define CONFIG_CMD_USB +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 5 +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI +#define CONFIG_PCI_EHCI_DEVICE 0 +#define CONFIG_USB_EHCI_PCI +#define CONFIG_PREBOOT "usb start;" +#endif /* #if defiend(CONFIG_FTPCI100) */ +#endif /* #if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI) */ + +/* + * IDE/ATA stuff + */ +#define __io +#define CONFIG_IDE_AHB +#define CONFIG_IDE_FTIDE020 + +#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ +#undef CONFIG_IDE_LED /* no led for ide supported */ +#define CONFIG_IDE_RESET 1 /* reset for ide supported */ +#define CONFIG_IDE_PREINIT 1 /* preinit for ide */ + +/* max: 2 IDE busses */ +#define CONFIG_SYS_IDE_MAXBUS 1 /* origin: 2 */ +/* max: 2 drives per IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 1 /* origin: (MAXBUS * 2) */ + +#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_FTIDE020S_BASE +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* for data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* for normal regs access */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* for alternate regs */ + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_SUPPORT_VFAT + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "NDS32 # " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) + +/* max number of command args */ +#define CONFIG_SYS_MAXARGS 16 + +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +/* + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */ + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) + +/* + * size in bytes reserved for initial data +*/ +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +/* + * AHB Controller configuration + */ +#define CONFIG_FTAHBC020S + +#ifdef CONFIG_FTAHBC020S +#include <faraday/ftahbc020s.h> + +/* Address of PHYS_SDRAM_0 before memory remap is at 0x(100)00000 */ +#define CONFIG_SYS_FTAHBC020S_SLAVE_BSR_BASE 0x100 + +/* + * CONFIG_SYS_FTAHBC020S_SLAVE_BSR_6: this define is used in lowlevel_init.S, + * hence we cannot use FTAHBC020S_BSR_SIZE(2048) since it will use ffs() wrote + * in C language. + */ +#define CONFIG_SYS_FTAHBC020S_SLAVE_BSR_6 \ + (FTAHBC020S_SLAVE_BSR_BASE(CONFIG_SYS_FTAHBC020S_SLAVE_BSR_BASE) | \ + FTAHBC020S_SLAVE_BSR_SIZE(0xb)) +#endif + +/* + * Watchdog + */ +#define CONFIG_FTWDT010_WATCHDOG + +/* + * PCU Power Control Unit configuration + */ +#define CONFIG_ANDES_PCU + +#ifdef CONFIG_ANDES_PCU +#include <andestech/andes_pcu.h> + +#endif + +/* + * DDR DRAM controller configuration + */ +#define CONFIG_DWCDDR21MCTL + +#ifdef CONFIG_DWCDDR21MCTL +#include <synopsys/dwcddr21mctl.h> +/* DCR: + * 2GB: 0x000025d2, 2GB (1Gb x8 2 ranks) Micron/innoDisk/Transcend + * 1GB: 0x000021d2, 1GB (1Gb x8 1 rank) Micron/Transcend/innoDisk + * 512MB: 0x000025cc, Micron 512MB (512Mb x16 2 ranks) + * 512MB: 0x000021ca, Trenscend/innoDisk 512MB (512Mb x8 1 rank) + * 256MB: 0x000020d4, Micron 256MB (1Gb x16 1 ranks) + */ +#define CONFIG_SYS_DWCDDR21MCTL_CCR 0x00020004 +#define CONFIG_SYS_DWCDDR21MCTL_CCR2 (DWCDDR21MCTL_CCR_DTT(0x1) | \ + DWCDDR21MCTL_CCR_DFTLM(0x4) | \ + DWCDDR21MCTL_CCR_HOSTEN(0x1)) + +/* 0x04: 0x000020d4 */ +#define CONFIG_SYS_DWCDDR21MCTL_DCR 0x000020ca + +/* 0x08: 0x0000000f */ +#define CONFIG_SYS_DWCDDR21MCTL_IOCR 0x0000000f + +/* 0x10: 0x00034812 */ +#define CONFIG_SYS_DWCDDR21MCTL_DRR (DWCDDR21MCTL_DRR_TRFC(0x12) | \ + DWCDDR21MCTL_DRR_TRFPRD(0x0348)) +/* 0x24 */ +#define CONFIG_SYS_DWCDDR21MCTL_DLLCR0 DWCDDR21MCTL_DLLCR_PHASE(0x0) + +/* 0x4c: 0x00000040 */ +#define CONFIG_SYS_DWCDDR21MCTL_RSLR0 0x00000040 + +/* 0x5c: 0x000055CF */ +#define CONFIG_SYS_DWCDDR21MCTL_RDGR0 0x000055cf + +/* 0xa4: 0x00100000 */ +#define CONFIG_SYS_DWCDDR21MCTL_DTAR (DWCDDR21MCTL_DTAR_DTBANK(0x0) | \ + DWCDDR21MCTL_DTAR_DTROW(0x0100) | \ + DWCDDR21MCTL_DTAR_DTCOL(0x0)) +/* 0x1f0: 0x00000852 */ +#define CONFIG_SYS_DWCDDR21MCTL_MR (DWCDDR21MCTL_MR_WR(0x4) | \ + DWCDDR21MCTL_MR_CL(0x5) | \ + DWCDDR21MCTL_MR_BL(0x2)) +#endif + +/* + * Physical Memory Map + */ +#if defined(CONFIG_MEM_REMAP) || defined(CONFIG_SKIP_LOWLEVEL_INIT) +#define PHYS_SDRAM_0 0x00000000 /* SDRAM Bank #1 */ +#if defined(CONFIG_MEM_REMAP) +#define PHYS_SDRAM_0_AT_INIT 0x80000000 /* SDRAM Bank #1 before remap*/ +#endif +#else /* !CONFIG_SKIP_LOWLEVEL_INIT && !CONFIG_MEM_REMAP */ +#define PHYS_SDRAM_0 0x80000000 /* SDRAM Bank #1 */ +#endif + +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define PHYS_SDRAM_0_SIZE 0x10000000 /* 256 MB */ + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_0 + +#ifdef CONFIG_MEM_REMAP +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0xA0000 - \ + GENERATED_GBL_DATA_SIZE) +#else +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \ + GENERATED_GBL_DATA_SIZE) +#endif /* CONFIG_MEM_REMAP */ + +/* + * Load address and memory test area should agree with + * board/faraday/a320/config.mk + * Be careful not to overwrite U-boot itself. + */ +#define CONFIG_SYS_LOAD_ADDR 0x0CF00000 + +/* memtest works on 63 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_0 +#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_0 + 0x03F00000) + +/* + * Static memory controller configuration + */ + +/* + * FLASH and environment organization + */ +#define CONFIG_SYS_NO_FLASH + +/* + * Env Storage Settings + */ +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_SIZE 4096 + +#endif /* __CONFIG_H */ -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v3 4/4] board/adp-ag102: add configuration of adp-ag102 2012-02-28 5:46 ` [U-Boot] [PATCH v3 4/4] board/adp-ag102: add configuration of adp-ag102 Macpaul Lin @ 2012-04-22 8:52 ` Macpaul Lin 0 siblings, 0 replies; 8+ messages in thread From: Macpaul Lin @ 2012-04-22 8:52 UTC (permalink / raw) To: u-boot Hi Macpaul, 2012/2/28 Macpaul Lin <macpaul@gmail.com> > From: Macpaul Lin <macpaul@andestech.com> > > board: > Add config file of board adp-ag102 > Add adp-ag102 into boards.cfg > Add adp-ag102 into MAINTAINERS > > doc: > add README of ag102 > > Signed-off-by: Macpaul Lin <macpaul@andestech.com> > Applied to u-boot-nds32/master, Thanks. -- Best regards, Macpaul Lin ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v3 1/4] nds32/ag102: add header support of ag102 soc 2012-02-28 5:46 ` [U-Boot] [PATCH v3 1/4] nds32/ag102: add header support of ag102 soc Macpaul Lin ` (2 preceding siblings ...) 2012-02-28 5:46 ` [U-Boot] [PATCH v3 4/4] board/adp-ag102: add configuration of adp-ag102 Macpaul Lin @ 2012-04-22 8:54 ` Macpaul Lin 3 siblings, 0 replies; 8+ messages in thread From: Macpaul Lin @ 2012-04-22 8:54 UTC (permalink / raw) To: u-boot Hi Macpaul, 2012/2/28 Macpaul Lin <macpaul@gmail.com>: > From: Macpaul Lin <macpaul@andestech.com> > > Add device address offsets header of ag102 soc. > Add ag102 into mach-types.h. > Add asm-offsets.c for helping convert C headers into asm. > > Signed-off-by: Macpaul Lin <macpaul@andestech.com> > --- > Changes for v2-v3: > ?- No change. Applied to u-boot-nds32/master, Thanks. -- Best regards, Macpaul Lin ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2012-04-22 8:55 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <"CACCg+XMRYkOmrCRBDPpN1hQpvPX6CPHWzb87e1TPKewaH8j8tA@mail.gmail.com">
2012-02-28 5:46 ` [U-Boot] [PATCH v3 1/4] nds32/ag102: add header support of ag102 soc Macpaul Lin
2012-02-28 5:46 ` [U-Boot] [PATCH v3 2/4] nds32/ag102: add ag102 soc support Macpaul Lin
2012-04-22 8:55 ` Macpaul Lin
2012-02-28 5:46 ` [U-Boot] [PATCH v3 3/4] board/adp-ag102: add board specific files Macpaul Lin
2012-04-22 8:52 ` Macpaul Lin
2012-02-28 5:46 ` [U-Boot] [PATCH v3 4/4] board/adp-ag102: add configuration of adp-ag102 Macpaul Lin
2012-04-22 8:52 ` Macpaul Lin
2012-04-22 8:54 ` [U-Boot] [PATCH v3 1/4] nds32/ag102: add header support of ag102 soc Macpaul Lin
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.