From: Axel Lin <axel.lin@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>,
Liam Girdwood <lrg@ti.com>,
Mark Brown <broonie@opensource.wolfsonmicro.com>,
"Jett.Zhou" <jtzhou@marvell.com>
Subject: [PATCH RFT 1/3] regulator: 88pm8607: Use regulator_get_voltage_sel_regmap()
Date: Tue, 24 Apr 2012 09:52:32 +0800 [thread overview]
Message-ID: <1335232352.6470.1.camel@phoenix> (raw)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
---
drivers/regulator/88pm8607.c | 36 +++++++++---------------------------
1 files changed, 9 insertions(+), 27 deletions(-)
diff --git a/drivers/regulator/88pm8607.c b/drivers/regulator/88pm8607.c
index f5de1c5..c3482b9 100644
--- a/drivers/regulator/88pm8607.c
+++ b/drivers/regulator/88pm8607.c
@@ -27,8 +27,6 @@ struct pm8607_regulator_info {
unsigned int *vol_table;
unsigned int *vol_suspend;
- int vol_reg;
- int vol_shift;
int update_reg;
int update_bit;
int slope_double;
@@ -224,13 +222,13 @@ static int pm8607_list_voltage(struct regulator_dev *rdev, unsigned index)
static int pm8607_set_voltage_sel(struct regulator_dev *rdev, unsigned selector)
{
struct pm8607_regulator_info *info = rdev_get_drvdata(rdev);
- uint8_t val, mask;
+ uint8_t val;
int ret;
- val = (uint8_t)(selector << info->vol_shift);
- mask = (rdev->desc->n_voltages - 1) << info->vol_shift;
+ val = (uint8_t)(selector << (ffs(rdev->desc->vsel_mask) - 1));
- ret = pm860x_set_bits(info->i2c, info->vol_reg, mask, val);
+ ret = pm860x_set_bits(info->i2c, rdev->desc->vsel_reg,
+ rdev->desc->vsel_mask, val);
if (ret)
return ret;
switch (info->desc.id) {
@@ -244,26 +242,10 @@ static int pm8607_set_voltage_sel(struct regulator_dev *rdev, unsigned selector)
return ret;
}
-static int pm8607_get_voltage_sel(struct regulator_dev *rdev)
-{
- struct pm8607_regulator_info *info = rdev_get_drvdata(rdev);
- uint8_t val, mask;
- int ret;
-
- ret = pm860x_reg_read(info->i2c, info->vol_reg);
- if (ret < 0)
- return ret;
-
- mask = (rdev->desc->n_voltages - 1) << info->vol_shift;
- val = ((unsigned char)ret & mask) >> info->vol_shift;
-
- return val;
-}
-
static struct regulator_ops pm8607_regulator_ops = {
.list_voltage = pm8607_list_voltage,
.set_voltage_sel = pm8607_set_voltage_sel,
- .get_voltage_sel = pm8607_get_voltage_sel,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
@@ -278,11 +260,11 @@ static struct regulator_ops pm8607_regulator_ops = {
.id = PM8607_ID_##vreg, \
.owner = THIS_MODULE, \
.n_voltages = ARRAY_SIZE(vreg##_table), \
+ .vsel_reg = PM8607_##vreg, \
+ .vsel_mask = ARRAY_SIZE(vreg##_table) - 1, \
.enable_reg = PM8607_##ereg, \
.enable_mask = 1 << (ebit), \
}, \
- .vol_reg = PM8607_##vreg, \
- .vol_shift = (0), \
.update_reg = PM8607_##ureg, \
.update_bit = (ubit), \
.slope_double = (0), \
@@ -299,11 +281,11 @@ static struct regulator_ops pm8607_regulator_ops = {
.id = PM8607_ID_LDO##_id, \
.owner = THIS_MODULE, \
.n_voltages = ARRAY_SIZE(LDO##_id##_table), \
+ .vsel_reg = PM8607_##vreg, \
+ .vsel_mask = (ARRAY_SIZE(LDO##_id##_table) - 1) << (shift), \
.enable_reg = PM8607_##ereg, \
.enable_mask = 1 << (ebit), \
}, \
- .vol_reg = PM8607_##vreg, \
- .vol_shift = (shift), \
.slope_double = (0), \
.vol_table = (unsigned int *)&LDO##_id##_table, \
.vol_suspend = (unsigned int *)&LDO##_id##_suspend_table, \
--
1.7.5.4
next reply other threads:[~2012-04-24 1:52 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-04-24 1:52 Axel Lin [this message]
2012-04-24 1:54 ` [PATCH RFT 2/3] regulator: da9052: Use regulator_get_voltage_sel_regmap() Axel Lin
2012-05-04 12:30 ` Mark Brown
2012-04-24 1:56 ` [PATCH RFT 3/3] regulator: rc5t583: " Axel Lin
2012-05-04 12:32 ` Mark Brown
2012-05-04 12:38 ` [PATCH RFT 1/3] regulator: 88pm8607: " Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1335232352.6470.1.camel@phoenix \
--to=axel.lin@gmail.com \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=haojian.zhuang@marvell.com \
--cc=jtzhou@marvell.com \
--cc=linux-kernel@vger.kernel.org \
--cc=lrg@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.