From: John Crispin <blogic@openwrt.org>
To: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org, John Crispin <blogic@openwrt.org>
Subject: [PATCH V2 09/16] MIPS: ralink: adds support for RT2880 SoC family
Date: Fri, 12 Apr 2013 09:27:36 +0200 [thread overview]
Message-ID: <1365751663-5725-9-git-send-email-blogic@openwrt.org> (raw)
In-Reply-To: <1365751663-5725-1-git-send-email-blogic@openwrt.org>
Add support code for rt2880 SOC.
The code detects the SoC and registers the clk / pinmux settings.
Signed-off-by: John Crispin <blogic@openwrt.org>
---
arch/mips/Kconfig | 2 +-
arch/mips/include/asm/mach-ralink/rt288x.h | 49 ++++++++++
arch/mips/ralink/Kconfig | 3 +
arch/mips/ralink/Makefile | 1 +
arch/mips/ralink/Platform | 5 +
arch/mips/ralink/rt288x.c | 143 ++++++++++++++++++++++++++++
6 files changed, 202 insertions(+), 1 deletion(-)
create mode 100644 arch/mips/include/asm/mach-ralink/rt288x.h
create mode 100644 arch/mips/ralink/rt288x.c
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index 27a4bfa..c1997db 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -1144,7 +1144,7 @@ config BOOT_ELF32
config MIPS_L1_CACHE_SHIFT
int
- default "4" if MACH_DECSTATION || MIKROTIK_RB532 || PMC_MSP4200_EVAL
+ default "4" if MACH_DECSTATION || MIKROTIK_RB532 || PMC_MSP4200_EVAL || SOC_RT288X
default "6" if MIPS_CPU_SCACHE
default "7" if SGI_IP22 || SGI_IP27 || SGI_IP28 || SNI_RM || CPU_CAVIUM_OCTEON
default "5"
diff --git a/arch/mips/include/asm/mach-ralink/rt288x.h b/arch/mips/include/asm/mach-ralink/rt288x.h
new file mode 100644
index 0000000..ad8b42d
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/rt288x.h
@@ -0,0 +1,49 @@
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * Parts of this file are based on Ralink's 2.6.21 BSP
+ *
+ * Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2013 John Crispin <blogic@openwrt.org>
+ */
+
+#ifndef _RT288X_REGS_H_
+#define _RT288X_REGS_H_
+
+#define RT2880_SYSC_BASE 0x00300000
+
+#define SYSC_REG_CHIP_NAME0 0x00
+#define SYSC_REG_CHIP_NAME1 0x04
+#define SYSC_REG_CHIP_ID 0x0c
+#define SYSC_REG_SYSTEM_CONFIG 0x10
+#define SYSC_REG_CLKCFG 0x30
+
+#define RT2880_CHIP_NAME0 0x38325452
+#define RT2880_CHIP_NAME1 0x20203038
+
+#define CHIP_ID_ID_MASK 0xff
+#define CHIP_ID_ID_SHIFT 8
+#define CHIP_ID_REV_MASK 0xff
+
+#define SYSTEM_CONFIG_CPUCLK_SHIFT 20
+#define SYSTEM_CONFIG_CPUCLK_MASK 0x3
+#define SYSTEM_CONFIG_CPUCLK_250 0x0
+#define SYSTEM_CONFIG_CPUCLK_266 0x1
+#define SYSTEM_CONFIG_CPUCLK_280 0x2
+#define SYSTEM_CONFIG_CPUCLK_300 0x3
+
+#define RT2880_GPIO_MODE_I2C BIT(0)
+#define RT2880_GPIO_MODE_UART0 BIT(1)
+#define RT2880_GPIO_MODE_SPI BIT(2)
+#define RT2880_GPIO_MODE_UART1 BIT(3)
+#define RT2880_GPIO_MODE_JTAG BIT(4)
+#define RT2880_GPIO_MODE_MDIO BIT(5)
+#define RT2880_GPIO_MODE_SDRAM BIT(6)
+#define RT2880_GPIO_MODE_PCI BIT(7)
+
+#define CLKCFG_SRAM_CS_N_WDT BIT(9)
+
+#endif
diff --git a/arch/mips/ralink/Kconfig b/arch/mips/ralink/Kconfig
index a0b0197..6723b94 100644
--- a/arch/mips/ralink/Kconfig
+++ b/arch/mips/ralink/Kconfig
@@ -6,6 +6,9 @@ choice
help
Select Ralink MIPS SoC type.
+ config SOC_RT288X
+ bool "RT288x"
+
config SOC_RT305X
bool "RT305x"
select USB_ARCH_HAS_HCD
diff --git a/arch/mips/ralink/Makefile b/arch/mips/ralink/Makefile
index 939757f..6d826f2 100644
--- a/arch/mips/ralink/Makefile
+++ b/arch/mips/ralink/Makefile
@@ -8,6 +8,7 @@
obj-y := prom.o of.o reset.o clk.o irq.o
+obj-$(CONFIG_SOC_RT288X) += rt288x.o
obj-$(CONFIG_SOC_RT305X) += rt305x.o
obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
diff --git a/arch/mips/ralink/Platform b/arch/mips/ralink/Platform
index 6babd65..3f49e51 100644
--- a/arch/mips/ralink/Platform
+++ b/arch/mips/ralink/Platform
@@ -5,6 +5,11 @@ core-$(CONFIG_RALINK) += arch/mips/ralink/
cflags-$(CONFIG_RALINK) += -I$(srctree)/arch/mips/include/asm/mach-ralink
#
+# Ralink RT288x
+#
+load-$(CONFIG_SOC_RT288X) += 0xffffffff88000000
+
+#
# Ralink RT305x
#
load-$(CONFIG_SOC_RT305X) += 0xffffffff80000000
diff --git a/arch/mips/ralink/rt288x.c b/arch/mips/ralink/rt288x.c
new file mode 100644
index 0000000..8f3a0fa
--- /dev/null
+++ b/arch/mips/ralink/rt288x.c
@@ -0,0 +1,143 @@
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * Parts of this file are based on Ralink's 2.6.21 BSP
+ *
+ * Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2013 John Crispin <blogic@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+
+#include <asm/mipsregs.h>
+#include <asm/mach-ralink/ralink_regs.h>
+#include <asm/mach-ralink/rt288x.h>
+
+#include "common.h"
+
+struct ralink_pinmux_grp mode_mux[] = {
+ {
+ .name = "i2c",
+ .mask = RT2880_GPIO_MODE_I2C,
+ .gpio_first = 1,
+ .gpio_last = 2,
+ }, {
+ .name = "spi",
+ .mask = RT2880_GPIO_MODE_SPI,
+ .gpio_first = 3,
+ .gpio_last = 6,
+ }, {
+ .name = "uartlite",
+ .mask = RT2880_GPIO_MODE_UART0,
+ .gpio_first = 7,
+ .gpio_last = 14,
+ }, {
+ .name = "jtag",
+ .mask = RT2880_GPIO_MODE_JTAG,
+ .gpio_first = 17,
+ .gpio_last = 21,
+ }, {
+ .name = "mdio",
+ .mask = RT2880_GPIO_MODE_MDIO,
+ .gpio_first = 22,
+ .gpio_last = 23,
+ }, {
+ .name = "sdram",
+ .mask = RT2880_GPIO_MODE_SDRAM,
+ .gpio_first = 24,
+ .gpio_last = 39,
+ }, {
+ .name = "pci",
+ .mask = RT2880_GPIO_MODE_PCI,
+ .gpio_first = 40,
+ .gpio_last = 71,
+ }, {0}
+};
+
+void rt288x_wdt_reset(void)
+{
+ u32 t;
+
+ /* enable WDT reset output on pin SRAM_CS_N */
+ t = rt_sysc_r32(SYSC_REG_CLKCFG);
+ t |= CLKCFG_SRAM_CS_N_WDT;
+ rt_sysc_w32(t, SYSC_REG_CLKCFG);
+}
+
+struct ralink_pinmux rt_pinmux = {
+ .mode = mode_mux,
+ .wdt_reset = rt288x_wdt_reset,
+};
+
+void ralink_usb_platform(void)
+{
+}
+
+void __init ralink_clk_init(void)
+{
+ unsigned long cpu_rate;
+ u32 t = rt_sysc_r32(SYSC_REG_SYSTEM_CONFIG);
+ t = ((t >> SYSTEM_CONFIG_CPUCLK_SHIFT) & SYSTEM_CONFIG_CPUCLK_MASK);
+
+ switch (t) {
+ case SYSTEM_CONFIG_CPUCLK_250:
+ cpu_rate = 250000000;
+ break;
+ case SYSTEM_CONFIG_CPUCLK_266:
+ cpu_rate = 266666667;
+ break;
+ case SYSTEM_CONFIG_CPUCLK_280:
+ cpu_rate = 280000000;
+ break;
+ case SYSTEM_CONFIG_CPUCLK_300:
+ cpu_rate = 300000000;
+ break;
+ }
+
+ ralink_clk_add("cpu", cpu_rate);
+ ralink_clk_add("300100.timer", cpu_rate / 2);
+ ralink_clk_add("300120.watchdog", cpu_rate / 2);
+ ralink_clk_add("300500.uart", cpu_rate / 2);
+ ralink_clk_add("300c00.uartlite", cpu_rate / 2);
+ ralink_clk_add("400000.ethernet", cpu_rate / 2);
+}
+
+void __init ralink_of_remap(void)
+{
+ rt_sysc_membase = plat_of_remap_node("ralink,rt2880-sysc");
+ rt_memc_membase = plat_of_remap_node("ralink,rt2880-memc");
+
+ if (!rt_sysc_membase || !rt_memc_membase)
+ panic("Failed to remap core resources");
+}
+
+void prom_soc_init(struct ralink_soc_info *soc_info)
+{
+ void __iomem *sysc = (void __iomem *) KSEG1ADDR(RT2880_SYSC_BASE);
+ const char *name;
+ u32 n0;
+ u32 n1;
+ u32 id;
+
+ n0 = __raw_readl(sysc + SYSC_REG_CHIP_NAME0);
+ n1 = __raw_readl(sysc + SYSC_REG_CHIP_NAME1);
+ id = __raw_readl(sysc + SYSC_REG_CHIP_ID);
+
+ if (n0 == RT2880_CHIP_NAME0 && n1 == RT2880_CHIP_NAME1) {
+ soc_info->compatible = "ralink,r2880-soc";
+ name = "RT2880";
+ } else {
+ panic("rt288x: unknown SoC, n0:%08x n1:%08x", n0, n1);
+ }
+
+ snprintf(soc_info->sys_type, RAMIPS_SYS_TYPE_LEN,
+ "Ralink %s id:%u rev:%u",
+ name,
+ (id >> CHIP_ID_ID_SHIFT) & CHIP_ID_ID_MASK,
+ (id & CHIP_ID_REV_MASK));
+}
--
1.7.10.4
next prev parent reply other threads:[~2013-04-12 7:36 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-04-12 7:27 [PATCH V2 01/16] MIPS: ralink: add PCI IRQ handling John Crispin
2013-04-12 7:27 ` [PATCH V2 02/16] MIPS: ralink: fix RT305x clock setup John Crispin
2013-04-12 8:22 ` Gabor Juhos
2013-04-12 8:21 ` John Crispin
2013-04-12 13:00 ` Sergei Shtylyov
2013-04-12 7:27 ` [PATCH V2 03/16] MIPS: ralink: add missing comment in irq driver John Crispin
2013-04-12 8:24 ` Gabor Juhos
2013-04-12 7:27 ` [PATCH V2 04/16] MIPS: ralink: add RT5350 sdram register defines John Crispin
2013-04-12 8:29 ` Gabor Juhos
2013-04-12 7:27 ` [PATCH V2 05/16] MIPS: ralink: add RT3352 usb " John Crispin
2013-04-12 8:47 ` Gabor Juhos
2013-04-12 7:27 ` [PATCH V2 06/16] MIPS: ralink: extend RT3050 dtsi file John Crispin
2013-04-12 9:22 ` Gabor Juhos
2013-04-12 7:27 ` [PATCH V2 07/16] MIPS: ralink: add RT5350 " John Crispin
2013-04-12 9:25 ` Gabor Juhos
2013-04-12 7:27 ` [PATCH V2 08/16] MIPS: ralink: make early_printk work on RT2880 John Crispin
2013-04-12 9:28 ` Gabor Juhos
2013-04-12 7:27 ` John Crispin [this message]
2013-04-12 11:12 ` [PATCH V2 09/16] MIPS: ralink: adds support for RT2880 SoC family Gabor Juhos
2013-04-12 11:19 ` John Crispin
2013-04-12 17:03 ` Gabor Juhos
2013-04-12 7:27 ` [PATCH V2 10/16] MIPS: ralink: add rt2880 dts files John Crispin
2013-04-12 7:27 ` [PATCH V2 11/16] MIPS: ralink: adds support for RT3883 SoC family John Crispin
2013-04-12 11:13 ` Gabor Juhos
2013-04-12 7:27 ` [PATCH V2 12/16] MIPS: ralink: add rt3883 dts files John Crispin
2013-04-12 7:27 ` [PATCH V2 13/16] MIPS: ralink: adds support for MT7620 SoC family John Crispin
2013-04-12 7:27 ` [PATCH V2 14/16] MIPS: ralink: add MT7620 dts files John Crispin
2013-04-12 7:27 ` [PATCH V2 15/16] MIPS: ralink: add support for periodic timer irq John Crispin
2013-04-12 16:35 ` Gabor Juhos
2013-04-12 7:27 ` [PATCH V2 16/16] MIPS: ralink: add cpu-feature-overrides.h John Crispin
2013-04-12 17:20 ` Gabor Juhos
2013-04-12 8:21 ` [PATCH V2 01/16] MIPS: ralink: add PCI IRQ handling Gabor Juhos
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1365751663-5725-9-git-send-email-blogic@openwrt.org \
--to=blogic@openwrt.org \
--cc=linux-mips@linux-mips.org \
--cc=ralf@linux-mips.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.