All of lore.kernel.org
 help / color / mirror / Atom feed
From: Ondrej Zary <linux@rainbow-software.org>
To: Samuel Chessman <chessman@tux.org>
Cc: netdev@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH 2/9] tlan: Enable link monitoring
Date: Tue, 27 May 2014 23:38:40 +0200	[thread overview]
Message-ID: <1401226727-5508-3-git-send-email-linux@rainbow-software.org> (raw)
In-Reply-To: <1401226727-5508-1-git-send-email-linux@rainbow-software.org>

Enable old link monitoring code and modify it:
 - control LINK LED
 - use separate timer so it does not interfere with ACT LED

Tested with Olicom OC-2326.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
---
 drivers/net/ethernet/ti/tlan.c |  115 +++++++++++++++++-----------------------
 drivers/net/ethernet/ti/tlan.h |    3 +-
 2 files changed, 49 insertions(+), 69 deletions(-)

diff --git a/drivers/net/ethernet/ti/tlan.c b/drivers/net/ethernet/ti/tlan.c
index e7449cb..c75ad6b 100644
--- a/drivers/net/ethernet/ti/tlan.c
+++ b/drivers/net/ethernet/ti/tlan.c
@@ -69,10 +69,6 @@ MODULE_AUTHOR("Maintainer: Samuel Chessman <chessman@tux.org>");
 MODULE_DESCRIPTION("Driver for TI ThunderLAN based ethernet PCI adapters");
 MODULE_LICENSE("GPL");
 
-
-/* Define this to enable Link beat monitoring */
-#undef MONITOR
-
 /* Turn on debugging. See Documentation/networking/tlan.txt for details */
 static  int		debug;
 module_param(debug, int, 0);
@@ -194,9 +190,7 @@ static void	tlan_phy_power_up(struct net_device *);
 static void	tlan_phy_reset(struct net_device *);
 static void	tlan_phy_start_link(struct net_device *);
 static void	tlan_phy_finish_auto_neg(struct net_device *);
-#ifdef MONITOR
-static void     tlan_phy_monitor(struct net_device *);
-#endif
+static void     tlan_phy_monitor(unsigned long);
 
 /*
   static int	tlan_phy_nop(struct net_device *);
@@ -340,6 +334,7 @@ static void tlan_stop(struct net_device *dev)
 {
 	struct tlan_priv *priv = netdev_priv(dev);
 
+	del_timer_sync(&priv->media_timer);
 	tlan_read_and_clear_stats(dev, TLAN_RECORD);
 	outl(TLAN_HC_AD_RST, dev->base_addr + TLAN_HOST_CMD);
 	/* Reset and power down phy */
@@ -889,6 +884,7 @@ static int tlan_open(struct net_device *dev)
 	}
 
 	init_timer(&priv->timer);
+	init_timer(&priv->media_timer);
 
 	tlan_start(dev);
 
@@ -1811,11 +1807,6 @@ static void tlan_timer(unsigned long data)
 	priv->timer.function = NULL;
 
 	switch (priv->timer_type) {
-#ifdef MONITOR
-	case TLAN_TIMER_LINK_BEAT:
-		tlan_phy_monitor(dev);
-		break;
-#endif
 	case TLAN_TIMER_PHY_PDOWN:
 		tlan_phy_power_down(dev);
 		break;
@@ -1859,8 +1850,6 @@ static void tlan_timer(unsigned long data)
 }
 
 
-
-
 /*****************************************************************************
 ******************************************************************************
 
@@ -2258,42 +2247,39 @@ tlan_finish_reset(struct net_device *dev)
 		tlan_mii_read_reg(dev, phy, MII_GEN_STS, &status);
 		udelay(1000);
 		tlan_mii_read_reg(dev, phy, MII_GEN_STS, &status);
-		if ((status & MII_GS_LINK) &&
-		    /* We only support link info on Nat.Sem. PHY's */
-		    (tlphy_id1 == NAT_SEM_ID1) &&
-		    (tlphy_id2 == NAT_SEM_ID2)) {
-			tlan_mii_read_reg(dev, phy, MII_AN_LPA, &partner);
-			tlan_mii_read_reg(dev, phy, TLAN_TLPHY_PAR, &tlphy_par);
-
-			netdev_info(dev,
-				    "Link active with %s %uMbps %s-Duplex\n",
-				    !(tlphy_par & TLAN_PHY_AN_EN_STAT)
-				    ? "forced" : "Autonegotiation enabled,",
-				    tlphy_par & TLAN_PHY_SPEED_100
-				    ? 100 : 10,
-				    tlphy_par & TLAN_PHY_DUPLEX_FULL
-				    ? "Full" : "Half");
-
-			if (tlphy_par & TLAN_PHY_AN_EN_STAT) {
-				netdev_info(dev, "Partner capability:");
-				for (i = 5; i < 10; i++)
-					if (partner & (1 << i))
-						pr_cont(" %s", media[i-5]);
-				pr_cont("\n");
-			}
-
-			tlan_dio_write8(dev->base_addr, TLAN_LED_REG,
-					TLAN_LED_LINK);
-#ifdef MONITOR
-			/* We have link beat..for now anyway */
-			priv->link = 1;
-			/*Enabling link beat monitoring */
-			tlan_set_timer(dev, (10*HZ), TLAN_TIMER_LINK_BEAT);
-#endif
-		} else if (status & MII_GS_LINK)  {
-			netdev_info(dev, "Link active\n");
-			tlan_dio_write8(dev->base_addr, TLAN_LED_REG,
-					TLAN_LED_LINK);
+		if (status & MII_GS_LINK) {
+			/* We only support link info on Nat.Sem. PHY's */
+			if ((tlphy_id1 == NAT_SEM_ID1) &&
+			    (tlphy_id2 == NAT_SEM_ID2)) {
+				tlan_mii_read_reg(dev, phy, MII_AN_LPA,
+					&partner);
+				tlan_mii_read_reg(dev, phy, TLAN_TLPHY_PAR,
+					&tlphy_par);
+
+				netdev_info(dev,
+					"Link active, %s %uMbps %s-Duplex\n",
+					!(tlphy_par & TLAN_PHY_AN_EN_STAT)
+					? "forced" : "Autonegotiation enabled,",
+					tlphy_par & TLAN_PHY_SPEED_100
+					? 100 : 10,
+					tlphy_par & TLAN_PHY_DUPLEX_FULL
+					? "Full" : "Half");
+
+				if (tlphy_par & TLAN_PHY_AN_EN_STAT) {
+					netdev_info(dev, "Partner capability:");
+					for (i = 5; i < 10; i++)
+						if (partner & (1 << i))
+							pr_cont(" %s",
+								media[i-5]);
+					pr_cont("\n");
+				}
+			} else
+				netdev_info(dev, "Link active\n");
+			/* Enabling link beat monitoring */
+			priv->media_timer.function = tlan_phy_monitor;
+			priv->media_timer.data = (unsigned long) dev;
+			priv->media_timer.expires = jiffies + HZ;
+			add_timer(&priv->media_timer);
 		}
 	}
 
@@ -2315,6 +2301,7 @@ tlan_finish_reset(struct net_device *dev)
 			     dev->base_addr + TLAN_HOST_CMD + 1);
 		outl(priv->rx_list_dma, dev->base_addr + TLAN_CH_PARM);
 		outl(TLAN_HC_GO | TLAN_HC_RT, dev->base_addr + TLAN_HOST_CMD);
+		tlan_dio_write8(dev->base_addr, TLAN_LED_REG, TLAN_LED_LINK);
 		netif_carrier_on(dev);
 	} else {
 		netdev_info(dev, "Link inactive, will retry in 10 secs...\n");
@@ -2720,7 +2707,6 @@ static void tlan_phy_finish_auto_neg(struct net_device *dev)
 
 }
 
-#ifdef MONITOR
 
 /*********************************************************************
  *
@@ -2730,18 +2716,18 @@ static void tlan_phy_finish_auto_neg(struct net_device *dev)
  *	      None
  *
  *     Params:
- *	      dev	     The device structure of this device.
+ *	      data	     The device structure of this device.
  *
  *
  *     This function monitors PHY condition by reading the status
- *     register via the MII bus. This can be used to give info
- *     about link changes (up/down), and possible switch to alternate
- *     media.
+ *     register via the MII bus, controls LINK LED and notifies the
+ *     kernel about link state.
  *
  *******************************************************************/
 
-void tlan_phy_monitor(struct net_device *dev)
+static void tlan_phy_monitor(unsigned long data)
 {
+	struct net_device *dev = (struct net_device *) data;
 	struct tlan_priv *priv = netdev_priv(dev);
 	u16     phy;
 	u16     phy_status;
@@ -2753,30 +2739,25 @@ void tlan_phy_monitor(struct net_device *dev)
 
 	/* Check if link has been lost */
 	if (!(phy_status & MII_GS_LINK)) {
-		if (priv->link) {
-			priv->link = 0;
+		if (netif_carrier_ok(dev)) {
 			printk(KERN_DEBUG "TLAN: %s has lost link\n",
 			       dev->name);
+			tlan_dio_write8(dev->base_addr, TLAN_LED_REG, 0);
 			netif_carrier_off(dev);
-			tlan_set_timer(dev, (2*HZ), TLAN_TIMER_LINK_BEAT);
-			return;
 		}
 	}
 
 	/* Link restablished? */
-	if ((phy_status & MII_GS_LINK) && !priv->link) {
-		priv->link = 1;
+	if ((phy_status & MII_GS_LINK) && !netif_carrier_ok(dev)) {
+		tlan_dio_write8(dev->base_addr, TLAN_LED_REG, TLAN_LED_LINK);
 		printk(KERN_DEBUG "TLAN: %s has reestablished link\n",
 		       dev->name);
 		netif_carrier_on(dev);
 	}
-
-	/* Setup a new monitor */
-	tlan_set_timer(dev, (2*HZ), TLAN_TIMER_LINK_BEAT);
+	priv->media_timer.expires = jiffies + HZ;
+	add_timer(&priv->media_timer);
 }
 
-#endif /* MONITOR */
-
 
 /*****************************************************************************
 ******************************************************************************
diff --git a/drivers/net/ethernet/ti/tlan.h b/drivers/net/ethernet/ti/tlan.h
index 2eb33a2..4ced905 100644
--- a/drivers/net/ethernet/ti/tlan.h
+++ b/drivers/net/ethernet/ti/tlan.h
@@ -195,6 +195,7 @@ struct tlan_priv {
 	u32			timer_set_at;
 	u32			timer_type;
 	struct timer_list	timer;
+	struct timer_list	media_timer;
 	struct board		*adapter;
 	u32			adapter_rev;
 	u32			aui;
@@ -206,7 +207,6 @@ struct tlan_priv {
 	u8			tlan_rev;
 	u8			tlan_full_duplex;
 	spinlock_t		lock;
-	u8			link;
 	struct work_struct			tlan_tqueue;
 	u8			neg_be_verbose;
 };
@@ -219,7 +219,6 @@ struct tlan_priv {
 	 *
 	 ****************************************************************/
 
-#define TLAN_TIMER_LINK_BEAT		1
 #define TLAN_TIMER_ACTIVITY		2
 #define TLAN_TIMER_PHY_PDOWN		3
 #define TLAN_TIMER_PHY_PUP		4
-- 
Ondrej Zary


  parent reply	other threads:[~2014-05-27 21:42 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-05-27 21:38 [PATCH 0/9] tlan: Link handling improvements and Olicom fixes Ondrej Zary
2014-05-27 21:38 ` [PATCH 1/9] tlan: Enable activity LED on Olicom OC-2325 and OC-2326 Ondrej Zary
2014-05-27 21:38 ` Ondrej Zary [this message]
2014-05-27 21:38 ` [PATCH 3/9] tlan: Add ethtool support Ondrej Zary
2014-05-27 21:38 ` [PATCH 4/9] tlan: Fix MAC address byte order on OC-2325/OC-2326 Ondrej Zary
2014-05-27 21:38 ` [PATCH 5/9] tlan: Restart autonegotiation on link loss Ondrej Zary
2014-05-27 22:29   ` Florian Fainelli
2014-05-28  6:39     ` Ondrej Zary
2014-05-28 17:26       ` Florian Fainelli
2014-05-28 14:08   ` Sergei Shtylyov
2014-05-27 21:38 ` [PATCH 6/9] tlan: Don't scream if no link Ondrej Zary
2014-05-27 21:38 ` [PATCH 7/9] tlan: Make autonegotiation faster Ondrej Zary
2014-05-28 14:11   ` Sergei Shtylyov
2014-05-27 21:38 ` [PATCH 8/9] tlan: Add PHY reset timeout Ondrej Zary
2014-05-27 21:38 ` [PATCH 9/9] tlan: Don't disable internal PHY on cards that use it in 10 Mbps mode Ondrej Zary

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1401226727-5508-3-git-send-email-linux@rainbow-software.org \
    --to=linux@rainbow-software.org \
    --cc=chessman@tux.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.