Re: [PATCH v2] ARM: msm: Update the references to DEBUG_MSM_UARTx

[Paul Bolle <pebolle@tiscali.nl>]

On Mon, 2014-05-26 at 19:37 +0300, Georgi Djakov wrote:
> The Kconfig options DEBUG_MSM_UART1, DEBUG_MSM_UART2, DEBUG_MSM_UART3,
> MSM_DEBUG_UART1, MSM_DEBUG_UART2 and MSM_DEBUG_UART3 are removed, but 
> they are still referenced in the following files:
> 	arch/arm/mach-msm/io.c,
> 	arch/arm/mach-msm/board-trout.c
> 	arch/arm/mach-msm/board-trout-gpio.c
> 
> Fix this by updating the reference to the new Kconfig option.
> 
> Reported-by: Paul Bolle <pebolle@tiscali.nl>
> Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
> ---

This patch is included neither in v3.16-rc1 nor in next-20140619. Did it
run into problems or is it already queued somewhere?
 
> Changes since v1:
>  - Fixed similar issue in board-trout.c and board-trout-gpio.c
> 
>  Applies to next-20140526.
> 
>  arch/arm/mach-msm/board-trout-gpio.c |    2 +-
>  arch/arm/mach-msm/board-trout.c      |    2 +-
>  arch/arm/mach-msm/io.c               |    6 ++----
>  3 files changed, 4 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm/mach-msm/board-trout-gpio.c b/arch/arm/mach-msm/board-trout-gpio.c
> index 87e1d01..e24930e 100644
> --- a/arch/arm/mach-msm/board-trout-gpio.c
> +++ b/arch/arm/mach-msm/board-trout-gpio.c
> @@ -94,7 +94,7 @@ static int trout_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
>  	}
>  
>  static struct msm_gpio_chip msm_gpio_banks[] = {
> -#if defined(CONFIG_MSM_DEBUG_UART1)
> +#if defined(CONFIG_DEBUG_MSM_UART) && (CONFIG_DEBUG_UART_PHYS == 0xa9a00000)
>  	/* H2W pins <-> UART1 */
>  	TROUT_GPIO_BANK("MISC2", 0x00,   TROUT_GPIO_MISC2_BASE, 0x40),
>  #else
> diff --git a/arch/arm/mach-msm/board-trout.c b/arch/arm/mach-msm/board-trout.c
> index 015d544..8369dfd 100644
> --- a/arch/arm/mach-msm/board-trout.c
> +++ b/arch/arm/mach-msm/board-trout.c
> @@ -90,7 +90,7 @@ static void __init trout_map_io(void)
>  	msm_map_common_io();
>  	iotable_init(trout_io_desc, ARRAY_SIZE(trout_io_desc));
>  
> -#ifdef CONFIG_MSM_DEBUG_UART3
> +#if defined(CONFIG_DEBUG_MSM_UART) && (CONFIG_DEBUG_UART_PHYS == 0xa9c00000)
>  	/* route UART3 to the "H2W" extended usb connector */
>  	writeb(0x80, TROUT_CPLD_BASE + 0x00);
>  #endif
> diff --git a/arch/arm/mach-msm/io.c b/arch/arm/mach-msm/io.c
> index 34e0947..b042dca 100644
> --- a/arch/arm/mach-msm/io.c
> +++ b/arch/arm/mach-msm/io.c
> @@ -57,8 +57,7 @@ static struct map_desc msm_io_desc[] __initdata = {
>  		.length =   MSM_SHARED_RAM_SIZE,
>  		.type =     MT_DEVICE,
>  	},
> -#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
> -		defined(CONFIG_DEBUG_MSM_UART3)
> +#if defined(CONFIG_DEBUG_MSM_UART)
>  	{
>  		/* Must be last: virtual and pfn filled in by debug_ll_addr() */
>  		.length = SZ_4K,
> @@ -76,8 +75,7 @@ void __init msm_map_common_io(void)
>  	 * pages are peripheral interface or not.
>  	 */
>  	asm("mcr p15, 0, %0, c15, c2, 4" : : "r" (0));
> -#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
> -		defined(CONFIG_DEBUG_MSM_UART3)
> +#if defined(CONFIG_DEBUG_MSM_UART)
>  #ifdef CONFIG_MMU
>  	debug_ll_addr(&msm_io_desc[size - 1].pfn,
>  		      &msm_io_desc[size - 1].virtual);


Paul Bolle