* [PATCH v2] ARM: apq8064: Add pinmux and i2c pinctrl nodes @ 2014-08-20 12:02 ` Kiran Padwal 0 siblings, 0 replies; 8+ messages in thread From: Kiran Padwal @ 2014-08-20 12:02 UTC (permalink / raw) To: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, davidb Cc: devicetree, linux, linux-arm-msm, linux-kernel, linux-arm-kernel, Kiran Padwal This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. It also adds necessary DT support for i2c eeprom which is present on IFC6410. Tested on IFC6410 board. Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com> --- Chages since v1: - Renamed pinmux phandle "qcom_pinmux" to "tlmm_pinmux". - Updated pinmux interrupt. arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 29 ++++++++++++++ arch/arm/boot/dts/qcom-apq8064.dtsi | 59 ++++++++++++++++++++++++++++ 2 files changed, 88 insertions(+) diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts index 7c2441d..d52ac3c 100644 --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts @@ -5,6 +5,15 @@ compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; soc { + pinmux@800000 { + i2c1_pins: i2c1_pinmux { + mux { + pins = "gpio20", "gpio21"; + function = "gsbi1"; + }; + }; + }; + gsbi@16600000 { status = "ok"; qcom,mode = <GSBI_PROT_I2C_UART>; @@ -12,5 +21,25 @@ status = "ok"; }; }; + + gsbi1: gsbi@12440000 { + qcom,mode = <GSBI_PROT_I2C>; + status = "ok"; + + i2c1: i2c@12460000 { + status = "ok"; + + clock-frequency = <200000>; + + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; + + eeprom: eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + pagesize = <32>; + }; + }; + }; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index 92bf793..bb2ccde 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -70,6 +70,17 @@ ranges; compatible = "simple-bus"; + tlmm_pinmux: pinmux@800000 { + compatible = "qcom,apq8064-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 16 0x4>; + }; + intc: interrupt-controller@2000000 { compatible = "qcom,msm-qgic2"; interrupt-controller; @@ -133,6 +144,54 @@ regulator; }; + gsbi1: gsbi@12440000 { + compatible = "qcom,gsbi-v1.0.0"; + reg = <0x12440000 0x100>; + clocks = <&gcc GSBI1_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + i2c@12460000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x12460000 0x1000>; + interrupts = <0 194 0>; + + clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + gsbi2: gsbi@12480000 { + compatible = "qcom,gsbi-v1.0.0"; + reg = <0x12480000 0x100>; + clocks = <&gcc GSBI2_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + i2c@124a0000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x124a0000 0x1000>; + interrupts = <0 196 0>; + + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; + }; + gsbi7: gsbi@16600000 { status = "disabled"; compatible = "qcom,gsbi-v1.0.0"; -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2] ARM: apq8064: Add pinmux and i2c pinctrl nodes @ 2014-08-20 12:02 ` Kiran Padwal 0 siblings, 0 replies; 8+ messages in thread From: Kiran Padwal @ 2014-08-20 12:02 UTC (permalink / raw) To: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, davidb Cc: devicetree, linux, linux-arm-kernel, linux-arm-msm, linux-kernel, Kiran Padwal This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. It also adds necessary DT support for i2c eeprom which is present on IFC6410. Tested on IFC6410 board. Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com> --- Chages since v1: - Renamed pinmux phandle "qcom_pinmux" to "tlmm_pinmux". - Updated pinmux interrupt. arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 29 ++++++++++++++ arch/arm/boot/dts/qcom-apq8064.dtsi | 59 ++++++++++++++++++++++++++++ 2 files changed, 88 insertions(+) diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts index 7c2441d..d52ac3c 100644 --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts @@ -5,6 +5,15 @@ compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; soc { + pinmux@800000 { + i2c1_pins: i2c1_pinmux { + mux { + pins = "gpio20", "gpio21"; + function = "gsbi1"; + }; + }; + }; + gsbi@16600000 { status = "ok"; qcom,mode = <GSBI_PROT_I2C_UART>; @@ -12,5 +21,25 @@ status = "ok"; }; }; + + gsbi1: gsbi@12440000 { + qcom,mode = <GSBI_PROT_I2C>; + status = "ok"; + + i2c1: i2c@12460000 { + status = "ok"; + + clock-frequency = <200000>; + + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; + + eeprom: eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + pagesize = <32>; + }; + }; + }; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index 92bf793..bb2ccde 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -70,6 +70,17 @@ ranges; compatible = "simple-bus"; + tlmm_pinmux: pinmux@800000 { + compatible = "qcom,apq8064-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 16 0x4>; + }; + intc: interrupt-controller@2000000 { compatible = "qcom,msm-qgic2"; interrupt-controller; @@ -133,6 +144,54 @@ regulator; }; + gsbi1: gsbi@12440000 { + compatible = "qcom,gsbi-v1.0.0"; + reg = <0x12440000 0x100>; + clocks = <&gcc GSBI1_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + i2c@12460000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x12460000 0x1000>; + interrupts = <0 194 0>; + + clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + gsbi2: gsbi@12480000 { + compatible = "qcom,gsbi-v1.0.0"; + reg = <0x12480000 0x100>; + clocks = <&gcc GSBI2_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + i2c@124a0000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x124a0000 0x1000>; + interrupts = <0 196 0>; + + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; + }; + gsbi7: gsbi@16600000 { status = "disabled"; compatible = "qcom,gsbi-v1.0.0"; -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2] ARM: apq8064: Add pinmux and i2c pinctrl nodes @ 2014-08-20 12:02 ` Kiran Padwal 0 siblings, 0 replies; 8+ messages in thread From: Kiran Padwal @ 2014-08-20 12:02 UTC (permalink / raw) To: linux-arm-kernel This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. It also adds necessary DT support for i2c eeprom which is present on IFC6410. Tested on IFC6410 board. Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com> --- Chages since v1: - Renamed pinmux phandle "qcom_pinmux" to "tlmm_pinmux". - Updated pinmux interrupt. arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 29 ++++++++++++++ arch/arm/boot/dts/qcom-apq8064.dtsi | 59 ++++++++++++++++++++++++++++ 2 files changed, 88 insertions(+) diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts index 7c2441d..d52ac3c 100644 --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts @@ -5,6 +5,15 @@ compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; soc { + pinmux at 800000 { + i2c1_pins: i2c1_pinmux { + mux { + pins = "gpio20", "gpio21"; + function = "gsbi1"; + }; + }; + }; + gsbi at 16600000 { status = "ok"; qcom,mode = <GSBI_PROT_I2C_UART>; @@ -12,5 +21,25 @@ status = "ok"; }; }; + + gsbi1: gsbi at 12440000 { + qcom,mode = <GSBI_PROT_I2C>; + status = "ok"; + + i2c1: i2c at 12460000 { + status = "ok"; + + clock-frequency = <200000>; + + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; + + eeprom: eeprom at 52 { + compatible = "atmel,24c128"; + reg = <0x52>; + pagesize = <32>; + }; + }; + }; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index 92bf793..bb2ccde 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -70,6 +70,17 @@ ranges; compatible = "simple-bus"; + tlmm_pinmux: pinmux at 800000 { + compatible = "qcom,apq8064-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 16 0x4>; + }; + intc: interrupt-controller at 2000000 { compatible = "qcom,msm-qgic2"; interrupt-controller; @@ -133,6 +144,54 @@ regulator; }; + gsbi1: gsbi at 12440000 { + compatible = "qcom,gsbi-v1.0.0"; + reg = <0x12440000 0x100>; + clocks = <&gcc GSBI1_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + i2c at 12460000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x12460000 0x1000>; + interrupts = <0 194 0>; + + clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + gsbi2: gsbi at 12480000 { + compatible = "qcom,gsbi-v1.0.0"; + reg = <0x12480000 0x100>; + clocks = <&gcc GSBI2_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + i2c at 124a0000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x124a0000 0x1000>; + interrupts = <0 196 0>; + + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; + }; + gsbi7: gsbi at 16600000 { status = "disabled"; compatible = "qcom,gsbi-v1.0.0"; -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v2] ARM: apq8064: Add pinmux and i2c pinctrl nodes 2014-08-20 12:02 ` Kiran Padwal @ 2014-08-20 15:36 ` Andreas Färber -1 siblings, 0 replies; 8+ messages in thread From: Andreas Färber @ 2014-08-20 15:36 UTC (permalink / raw) To: Kiran Padwal, robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, davidb Cc: devicetree, linux, linux-arm-kernel, linux-arm-msm, linux-kernel Hi, Am 20.08.2014 14:02, schrieb Kiran Padwal: > This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. > It also adds necessary DT support for i2c eeprom which is present on > IFC6410. > > Tested on IFC6410 board. > > Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com> > --- > Chages since v1: > - Renamed pinmux phandle "qcom_pinmux" to "tlmm_pinmux". > - Updated pinmux interrupt. > > arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 29 ++++++++++++++ > arch/arm/boot/dts/qcom-apq8064.dtsi | 59 ++++++++++++++++++++++++++++ > 2 files changed, 88 insertions(+) > > diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts > index 7c2441d..d52ac3c 100644 > --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts > +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts > @@ -5,6 +5,15 @@ > compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; > > soc { > + pinmux@800000 { > + i2c1_pins: i2c1_pinmux { Is there a requirement to have "_pinmux" in the subnode of the "pinmux" node? Otherwise use just "i2c1"? I notice because the general convention seems to be dashes rather than underscores for node names. > + mux { > + pins = "gpio20", "gpio21"; > + function = "gsbi1"; > + }; > + }; > + }; > + > gsbi@16600000 { > status = "ok"; > qcom,mode = <GSBI_PROT_I2C_UART>; > @@ -12,5 +21,25 @@ > status = "ok"; > }; > }; > + > + gsbi1: gsbi@12440000 { > + qcom,mode = <GSBI_PROT_I2C>; > + status = "ok"; Usually the overridden status property goes first, as seen on the previous gsbi node. Further, its canonical value is "okay" (although in practice anything other than "disabled" should work), so suggest you adopt it for your new nodes. Also, you already provide a label "gsbi1" to this node in the .dtsi below, so you don't need to do it here again. Some architectures prefer in such a case that in the .dts the node is referenced as &gsbi1 {...}; below the root node in alphabetical order rather than duplicating the full /soc/foo@bar hierarchy. > + > + i2c1: i2c@12460000 { Suggest to move the i2c1 label to the .dtsi. Then optionally same could be done here as outlined for gsbi1. > + status = "ok"; "okay". > + > + clock-frequency = <200000>; > + > + pinctrl-0 = <&i2c1_pins>; > + pinctrl-names = "default"; > + > + eeprom: eeprom@52 { > + compatible = "atmel,24c128"; > + reg = <0x52>; > + pagesize = <32>; > + }; > + }; > + }; > }; > }; > diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi > index 92bf793..bb2ccde 100644 > --- a/arch/arm/boot/dts/qcom-apq8064.dtsi > +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi > @@ -70,6 +70,17 @@ > ranges; > compatible = "simple-bus"; > > + tlmm_pinmux: pinmux@800000 { > + compatible = "qcom,apq8064-pinctrl"; > + reg = <0x800000 0x4000>; > + > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + interrupts = <0 16 0x4>; s/0x4/IRQ_TYPE_LEVEL_HIGH/? > + }; > + > intc: interrupt-controller@2000000 { > compatible = "qcom,msm-qgic2"; > interrupt-controller; > @@ -133,6 +144,54 @@ > regulator; > }; > > + gsbi1: gsbi@12440000 { > + compatible = "qcom,gsbi-v1.0.0"; > + reg = <0x12440000 0x100>; > + clocks = <&gcc GSBI1_H_CLK>; > + clock-names = "iface"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + status = "disabled"; > + > + i2c@12460000 { > + compatible = "qcom,i2c-qup-v1.1.1"; > + reg = <0x12460000 0x1000>; > + interrupts = <0 194 0>; The trailing 0 might be IRQ_TYPE_NONE? > + > + clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; > + clock-names = "core", "iface"; > + status = "disabled"; I'd guess this is redundant since the parent is already disabled? > + > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > + > + gsbi2: gsbi@12480000 { > + compatible = "qcom,gsbi-v1.0.0"; > + reg = <0x12480000 0x100>; > + clocks = <&gcc GSBI2_H_CLK>; > + clock-names = "iface"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + status = "disabled"; > + > + i2c@124a0000 { > + compatible = "qcom,i2c-qup-v1.1.1"; > + reg = <0x124a0000 0x1000>; > + interrupts = <0 196 0>; Again, IRQ_TYPE_NONE possibly? Cheers, Andreas > + > + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; > + clock-names = "core", "iface"; > + status = "disabled"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > + > gsbi7: gsbi@16600000 { > status = "disabled"; > compatible = "qcom,gsbi-v1.0.0"; -- SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v2] ARM: apq8064: Add pinmux and i2c pinctrl nodes @ 2014-08-20 15:36 ` Andreas Färber 0 siblings, 0 replies; 8+ messages in thread From: Andreas Färber @ 2014-08-20 15:36 UTC (permalink / raw) To: linux-arm-kernel Hi, Am 20.08.2014 14:02, schrieb Kiran Padwal: > This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. > It also adds necessary DT support for i2c eeprom which is present on > IFC6410. > > Tested on IFC6410 board. > > Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com> > --- > Chages since v1: > - Renamed pinmux phandle "qcom_pinmux" to "tlmm_pinmux". > - Updated pinmux interrupt. > > arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 29 ++++++++++++++ > arch/arm/boot/dts/qcom-apq8064.dtsi | 59 ++++++++++++++++++++++++++++ > 2 files changed, 88 insertions(+) > > diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts > index 7c2441d..d52ac3c 100644 > --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts > +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts > @@ -5,6 +5,15 @@ > compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; > > soc { > + pinmux at 800000 { > + i2c1_pins: i2c1_pinmux { Is there a requirement to have "_pinmux" in the subnode of the "pinmux" node? Otherwise use just "i2c1"? I notice because the general convention seems to be dashes rather than underscores for node names. > + mux { > + pins = "gpio20", "gpio21"; > + function = "gsbi1"; > + }; > + }; > + }; > + > gsbi at 16600000 { > status = "ok"; > qcom,mode = <GSBI_PROT_I2C_UART>; > @@ -12,5 +21,25 @@ > status = "ok"; > }; > }; > + > + gsbi1: gsbi at 12440000 { > + qcom,mode = <GSBI_PROT_I2C>; > + status = "ok"; Usually the overridden status property goes first, as seen on the previous gsbi node. Further, its canonical value is "okay" (although in practice anything other than "disabled" should work), so suggest you adopt it for your new nodes. Also, you already provide a label "gsbi1" to this node in the .dtsi below, so you don't need to do it here again. Some architectures prefer in such a case that in the .dts the node is referenced as &gsbi1 {...}; below the root node in alphabetical order rather than duplicating the full /soc/foo at bar hierarchy. > + > + i2c1: i2c at 12460000 { Suggest to move the i2c1 label to the .dtsi. Then optionally same could be done here as outlined for gsbi1. > + status = "ok"; "okay". > + > + clock-frequency = <200000>; > + > + pinctrl-0 = <&i2c1_pins>; > + pinctrl-names = "default"; > + > + eeprom: eeprom at 52 { > + compatible = "atmel,24c128"; > + reg = <0x52>; > + pagesize = <32>; > + }; > + }; > + }; > }; > }; > diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi > index 92bf793..bb2ccde 100644 > --- a/arch/arm/boot/dts/qcom-apq8064.dtsi > +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi > @@ -70,6 +70,17 @@ > ranges; > compatible = "simple-bus"; > > + tlmm_pinmux: pinmux at 800000 { > + compatible = "qcom,apq8064-pinctrl"; > + reg = <0x800000 0x4000>; > + > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + interrupts = <0 16 0x4>; s/0x4/IRQ_TYPE_LEVEL_HIGH/? > + }; > + > intc: interrupt-controller at 2000000 { > compatible = "qcom,msm-qgic2"; > interrupt-controller; > @@ -133,6 +144,54 @@ > regulator; > }; > > + gsbi1: gsbi at 12440000 { > + compatible = "qcom,gsbi-v1.0.0"; > + reg = <0x12440000 0x100>; > + clocks = <&gcc GSBI1_H_CLK>; > + clock-names = "iface"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + status = "disabled"; > + > + i2c at 12460000 { > + compatible = "qcom,i2c-qup-v1.1.1"; > + reg = <0x12460000 0x1000>; > + interrupts = <0 194 0>; The trailing 0 might be IRQ_TYPE_NONE? > + > + clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; > + clock-names = "core", "iface"; > + status = "disabled"; I'd guess this is redundant since the parent is already disabled? > + > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > + > + gsbi2: gsbi at 12480000 { > + compatible = "qcom,gsbi-v1.0.0"; > + reg = <0x12480000 0x100>; > + clocks = <&gcc GSBI2_H_CLK>; > + clock-names = "iface"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + status = "disabled"; > + > + i2c at 124a0000 { > + compatible = "qcom,i2c-qup-v1.1.1"; > + reg = <0x124a0000 0x1000>; > + interrupts = <0 196 0>; Again, IRQ_TYPE_NONE possibly? Cheers, Andreas > + > + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; > + clock-names = "core", "iface"; > + status = "disabled"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > + > gsbi7: gsbi at 16600000 { > status = "disabled"; > compatible = "qcom,gsbi-v1.0.0"; -- SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany GF: Jeff Hawn, Jennifer Guild, Felix Imend?rffer; HRB 16746 AG N?rnberg ^ permalink raw reply [flat|nested] 8+ messages in thread
[parent not found: <53F4C085.5060101-l3A5Bk7waGM@public.gmane.org>]
* Re: [PATCH v2] ARM: apq8064: Add pinmux and i2c pinctrl nodes 2014-08-20 15:36 ` Andreas Färber (?) @ 2014-08-26 9:42 ` kiran.padwal at smartplayin.com -1 siblings, 0 replies; 8+ messages in thread From: kiran.padwal-edOiRQu9Xnj5XLMNweQjbQ @ 2014-08-26 9:42 UTC (permalink / raw) To: Andreas Färber Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8, mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg, galak-sgV2jX0FEOL9JmXXK+q4OQ, davidb-sgV2jX0FEOL9JmXXK+q4OQ, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-lFZ/pmaqli7XmaaqVzeoHQ, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-arm-msm-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA On Wednesday, August 20, 2014 11:36am, "Andreas Färber" <afaerber@suse.de> said: > Hi, > > Am 20.08.2014 14:02, schrieb Kiran Padwal: >> This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. >> It also adds necessary DT support for i2c eeprom which is present on >> IFC6410. >> >> Tested on IFC6410 board. >> >> Signed-off-by: Kiran Padwal <kiran.padwal-edOiRQu9Xnj5XLMNweQjbQ@public.gmane.org> >> --- >> Chages since v1: >> - Renamed pinmux phandle "qcom_pinmux" to "tlmm_pinmux". >> - Updated pinmux interrupt. >> >> arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 29 ++++++++++++++ >> arch/arm/boot/dts/qcom-apq8064.dtsi | 59 ++++++++++++++++++++++++++++ >> 2 files changed, 88 insertions(+) >> >> diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> index 7c2441d..d52ac3c 100644 >> --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> @@ -5,6 +5,15 @@ >> compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; >> >> soc { >> + pinmux@800000 { >> + i2c1_pins: i2c1_pinmux { > > Is there a requirement to have "_pinmux" in the subnode of the "pinmux" > node? Otherwise use just "i2c1"? I notice because the general convention > seems to be dashes rather than underscores for node names. Ok, I will change it to i2c1. > >> + mux { >> + pins = "gpio20", "gpio21"; >> + function = "gsbi1"; >> + }; >> + }; >> + }; >> + >> gsbi@16600000 { >> status = "ok"; >> qcom,mode = <GSBI_PROT_I2C_UART>; >> @@ -12,5 +21,25 @@ >> status = "ok"; >> }; >> }; >> + >> + gsbi1: gsbi@12440000 { >> + qcom,mode = <GSBI_PROT_I2C>; >> + status = "ok"; > > Usually the overridden status property goes first, as seen on the > previous gsbi node. > > Further, its canonical value is "okay" (although in practice anything > other than "disabled" should work), so suggest you adopt it for your new > nodes. > > Also, you already provide a label "gsbi1" to this node in the .dtsi > below, so you don't need to do it here again. > Some architectures prefer in such a case that in the .dts the node is > referenced as &gsbi1 {...}; below the root node in alphabetical order > rather than duplicating the full /soc/foo@bar hierarchy. Indeed, I'll change on v3. > >> + >> + i2c1: i2c@12460000 { > > Suggest to move the i2c1 label to the .dtsi. Then optionally same could > be done here as outlined for gsbi1. Indeed, I'll change on v3. > >> + status = "ok"; > > "okay". Ok. > >> + >> + clock-frequency = <200000>; >> + >> + pinctrl-0 = <&i2c1_pins>; >> + pinctrl-names = "default"; >> + >> + eeprom: eeprom@52 { >> + compatible = "atmel,24c128"; >> + reg = <0x52>; >> + pagesize = <32>; >> + }; >> + }; >> + }; >> }; >> }; >> diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi >> b/arch/arm/boot/dts/qcom-apq8064.dtsi >> index 92bf793..bb2ccde 100644 >> --- a/arch/arm/boot/dts/qcom-apq8064.dtsi >> +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi >> @@ -70,6 +70,17 @@ >> ranges; >> compatible = "simple-bus"; >> >> + tlmm_pinmux: pinmux@800000 { >> + compatible = "qcom,apq8064-pinctrl"; >> + reg = <0x800000 0x4000>; >> + >> + gpio-controller; >> + #gpio-cells = <2>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + interrupts = <0 16 0x4>; > > s/0x4/IRQ_TYPE_LEVEL_HIGH/? Indeed, I'll change on v3. > >> + }; >> + >> intc: interrupt-controller@2000000 { >> compatible = "qcom,msm-qgic2"; >> interrupt-controller; >> @@ -133,6 +144,54 @@ >> regulator; >> }; >> >> + gsbi1: gsbi@12440000 { >> + compatible = "qcom,gsbi-v1.0.0"; >> + reg = <0x12440000 0x100>; >> + clocks = <&gcc GSBI1_H_CLK>; >> + clock-names = "iface"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + status = "disabled"; >> + >> + i2c@12460000 { >> + compatible = "qcom,i2c-qup-v1.1.1"; >> + reg = <0x12460000 0x1000>; >> + interrupts = <0 194 0>; > > The trailing 0 might be IRQ_TYPE_NONE? Indeed, I'll change on v3. > >> + >> + clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; >> + clock-names = "core", "iface"; >> + status = "disabled"; > > I'd guess this is redundant since the parent is already disabled? Indeed, I'll change on v3. > >> + >> + #address-cells = <1>; >> + #size-cells = <0>; >> + }; >> + }; >> + >> + gsbi2: gsbi@12480000 { >> + compatible = "qcom,gsbi-v1.0.0"; >> + reg = <0x12480000 0x100>; >> + clocks = <&gcc GSBI2_H_CLK>; >> + clock-names = "iface"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + status = "disabled"; >> + >> + i2c@124a0000 { >> + compatible = "qcom,i2c-qup-v1.1.1"; >> + reg = <0x124a0000 0x1000>; >> + interrupts = <0 196 0>; > > Again, IRQ_TYPE_NONE possibly? Indeed, I'll change on v3. Thanks. > > Cheers, > Andreas > >> + >> + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; >> + clock-names = "core", "iface"; >> + status = "disabled"; >> + >> + #address-cells = <1>; >> + #size-cells = <0>; >> + }; >> + }; >> + >> gsbi7: gsbi@16600000 { >> status = "disabled"; >> compatible = "qcom,gsbi-v1.0.0"; > > -- > SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany > GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2] ARM: apq8064: Add pinmux and i2c pinctrl nodes @ 2014-08-26 9:42 ` kiran.padwal at smartplayin.com 0 siblings, 0 replies; 8+ messages in thread From: kiran.padwal @ 2014-08-26 9:42 UTC (permalink / raw) To: Andreas Färber Cc: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, davidb, devicetree, linux, linux-arm-kernel, linux-arm-msm, linux-kernel On Wednesday, August 20, 2014 11:36am, "Andreas Färber" <afaerber@suse.de> said: > Hi, > > Am 20.08.2014 14:02, schrieb Kiran Padwal: >> This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. >> It also adds necessary DT support for i2c eeprom which is present on >> IFC6410. >> >> Tested on IFC6410 board. >> >> Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com> >> --- >> Chages since v1: >> - Renamed pinmux phandle "qcom_pinmux" to "tlmm_pinmux". >> - Updated pinmux interrupt. >> >> arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 29 ++++++++++++++ >> arch/arm/boot/dts/qcom-apq8064.dtsi | 59 ++++++++++++++++++++++++++++ >> 2 files changed, 88 insertions(+) >> >> diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> index 7c2441d..d52ac3c 100644 >> --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> @@ -5,6 +5,15 @@ >> compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; >> >> soc { >> + pinmux@800000 { >> + i2c1_pins: i2c1_pinmux { > > Is there a requirement to have "_pinmux" in the subnode of the "pinmux" > node? Otherwise use just "i2c1"? I notice because the general convention > seems to be dashes rather than underscores for node names. Ok, I will change it to i2c1. > >> + mux { >> + pins = "gpio20", "gpio21"; >> + function = "gsbi1"; >> + }; >> + }; >> + }; >> + >> gsbi@16600000 { >> status = "ok"; >> qcom,mode = <GSBI_PROT_I2C_UART>; >> @@ -12,5 +21,25 @@ >> status = "ok"; >> }; >> }; >> + >> + gsbi1: gsbi@12440000 { >> + qcom,mode = <GSBI_PROT_I2C>; >> + status = "ok"; > > Usually the overridden status property goes first, as seen on the > previous gsbi node. > > Further, its canonical value is "okay" (although in practice anything > other than "disabled" should work), so suggest you adopt it for your new > nodes. > > Also, you already provide a label "gsbi1" to this node in the .dtsi > below, so you don't need to do it here again. > Some architectures prefer in such a case that in the .dts the node is > referenced as &gsbi1 {...}; below the root node in alphabetical order > rather than duplicating the full /soc/foo@bar hierarchy. Indeed, I'll change on v3. > >> + >> + i2c1: i2c@12460000 { > > Suggest to move the i2c1 label to the .dtsi. Then optionally same could > be done here as outlined for gsbi1. Indeed, I'll change on v3. > >> + status = "ok"; > > "okay". Ok. > >> + >> + clock-frequency = <200000>; >> + >> + pinctrl-0 = <&i2c1_pins>; >> + pinctrl-names = "default"; >> + >> + eeprom: eeprom@52 { >> + compatible = "atmel,24c128"; >> + reg = <0x52>; >> + pagesize = <32>; >> + }; >> + }; >> + }; >> }; >> }; >> diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi >> b/arch/arm/boot/dts/qcom-apq8064.dtsi >> index 92bf793..bb2ccde 100644 >> --- a/arch/arm/boot/dts/qcom-apq8064.dtsi >> +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi >> @@ -70,6 +70,17 @@ >> ranges; >> compatible = "simple-bus"; >> >> + tlmm_pinmux: pinmux@800000 { >> + compatible = "qcom,apq8064-pinctrl"; >> + reg = <0x800000 0x4000>; >> + >> + gpio-controller; >> + #gpio-cells = <2>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + interrupts = <0 16 0x4>; > > s/0x4/IRQ_TYPE_LEVEL_HIGH/? Indeed, I'll change on v3. > >> + }; >> + >> intc: interrupt-controller@2000000 { >> compatible = "qcom,msm-qgic2"; >> interrupt-controller; >> @@ -133,6 +144,54 @@ >> regulator; >> }; >> >> + gsbi1: gsbi@12440000 { >> + compatible = "qcom,gsbi-v1.0.0"; >> + reg = <0x12440000 0x100>; >> + clocks = <&gcc GSBI1_H_CLK>; >> + clock-names = "iface"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + status = "disabled"; >> + >> + i2c@12460000 { >> + compatible = "qcom,i2c-qup-v1.1.1"; >> + reg = <0x12460000 0x1000>; >> + interrupts = <0 194 0>; > > The trailing 0 might be IRQ_TYPE_NONE? Indeed, I'll change on v3. > >> + >> + clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; >> + clock-names = "core", "iface"; >> + status = "disabled"; > > I'd guess this is redundant since the parent is already disabled? Indeed, I'll change on v3. > >> + >> + #address-cells = <1>; >> + #size-cells = <0>; >> + }; >> + }; >> + >> + gsbi2: gsbi@12480000 { >> + compatible = "qcom,gsbi-v1.0.0"; >> + reg = <0x12480000 0x100>; >> + clocks = <&gcc GSBI2_H_CLK>; >> + clock-names = "iface"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + status = "disabled"; >> + >> + i2c@124a0000 { >> + compatible = "qcom,i2c-qup-v1.1.1"; >> + reg = <0x124a0000 0x1000>; >> + interrupts = <0 196 0>; > > Again, IRQ_TYPE_NONE possibly? Indeed, I'll change on v3. Thanks. > > Cheers, > Andreas > >> + >> + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; >> + clock-names = "core", "iface"; >> + status = "disabled"; >> + >> + #address-cells = <1>; >> + #size-cells = <0>; >> + }; >> + }; >> + >> gsbi7: gsbi@16600000 { >> status = "disabled"; >> compatible = "qcom,gsbi-v1.0.0"; > > -- > SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany > GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg > ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v2] ARM: apq8064: Add pinmux and i2c pinctrl nodes @ 2014-08-26 9:42 ` kiran.padwal at smartplayin.com 0 siblings, 0 replies; 8+ messages in thread From: kiran.padwal at smartplayin.com @ 2014-08-26 9:42 UTC (permalink / raw) To: linux-arm-kernel On Wednesday, August 20, 2014 11:36am, "Andreas F?rber" <afaerber@suse.de> said: > Hi, > > Am 20.08.2014 14:02, schrieb Kiran Padwal: >> This patch adds pinmux and i2c pinctrl DT node for IFC6410 board. >> It also adds necessary DT support for i2c eeprom which is present on >> IFC6410. >> >> Tested on IFC6410 board. >> >> Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com> >> --- >> Chages since v1: >> - Renamed pinmux phandle "qcom_pinmux" to "tlmm_pinmux". >> - Updated pinmux interrupt. >> >> arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 29 ++++++++++++++ >> arch/arm/boot/dts/qcom-apq8064.dtsi | 59 ++++++++++++++++++++++++++++ >> 2 files changed, 88 insertions(+) >> >> diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> index 7c2441d..d52ac3c 100644 >> --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts >> @@ -5,6 +5,15 @@ >> compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; >> >> soc { >> + pinmux at 800000 { >> + i2c1_pins: i2c1_pinmux { > > Is there a requirement to have "_pinmux" in the subnode of the "pinmux" > node? Otherwise use just "i2c1"? I notice because the general convention > seems to be dashes rather than underscores for node names. Ok, I will change it to i2c1. > >> + mux { >> + pins = "gpio20", "gpio21"; >> + function = "gsbi1"; >> + }; >> + }; >> + }; >> + >> gsbi at 16600000 { >> status = "ok"; >> qcom,mode = <GSBI_PROT_I2C_UART>; >> @@ -12,5 +21,25 @@ >> status = "ok"; >> }; >> }; >> + >> + gsbi1: gsbi at 12440000 { >> + qcom,mode = <GSBI_PROT_I2C>; >> + status = "ok"; > > Usually the overridden status property goes first, as seen on the > previous gsbi node. > > Further, its canonical value is "okay" (although in practice anything > other than "disabled" should work), so suggest you adopt it for your new > nodes. > > Also, you already provide a label "gsbi1" to this node in the .dtsi > below, so you don't need to do it here again. > Some architectures prefer in such a case that in the .dts the node is > referenced as &gsbi1 {...}; below the root node in alphabetical order > rather than duplicating the full /soc/foo at bar hierarchy. Indeed, I'll change on v3. > >> + >> + i2c1: i2c at 12460000 { > > Suggest to move the i2c1 label to the .dtsi. Then optionally same could > be done here as outlined for gsbi1. Indeed, I'll change on v3. > >> + status = "ok"; > > "okay". Ok. > >> + >> + clock-frequency = <200000>; >> + >> + pinctrl-0 = <&i2c1_pins>; >> + pinctrl-names = "default"; >> + >> + eeprom: eeprom at 52 { >> + compatible = "atmel,24c128"; >> + reg = <0x52>; >> + pagesize = <32>; >> + }; >> + }; >> + }; >> }; >> }; >> diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi >> b/arch/arm/boot/dts/qcom-apq8064.dtsi >> index 92bf793..bb2ccde 100644 >> --- a/arch/arm/boot/dts/qcom-apq8064.dtsi >> +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi >> @@ -70,6 +70,17 @@ >> ranges; >> compatible = "simple-bus"; >> >> + tlmm_pinmux: pinmux at 800000 { >> + compatible = "qcom,apq8064-pinctrl"; >> + reg = <0x800000 0x4000>; >> + >> + gpio-controller; >> + #gpio-cells = <2>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + interrupts = <0 16 0x4>; > > s/0x4/IRQ_TYPE_LEVEL_HIGH/? Indeed, I'll change on v3. > >> + }; >> + >> intc: interrupt-controller at 2000000 { >> compatible = "qcom,msm-qgic2"; >> interrupt-controller; >> @@ -133,6 +144,54 @@ >> regulator; >> }; >> >> + gsbi1: gsbi at 12440000 { >> + compatible = "qcom,gsbi-v1.0.0"; >> + reg = <0x12440000 0x100>; >> + clocks = <&gcc GSBI1_H_CLK>; >> + clock-names = "iface"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + status = "disabled"; >> + >> + i2c at 12460000 { >> + compatible = "qcom,i2c-qup-v1.1.1"; >> + reg = <0x12460000 0x1000>; >> + interrupts = <0 194 0>; > > The trailing 0 might be IRQ_TYPE_NONE? Indeed, I'll change on v3. > >> + >> + clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; >> + clock-names = "core", "iface"; >> + status = "disabled"; > > I'd guess this is redundant since the parent is already disabled? Indeed, I'll change on v3. > >> + >> + #address-cells = <1>; >> + #size-cells = <0>; >> + }; >> + }; >> + >> + gsbi2: gsbi at 12480000 { >> + compatible = "qcom,gsbi-v1.0.0"; >> + reg = <0x12480000 0x100>; >> + clocks = <&gcc GSBI2_H_CLK>; >> + clock-names = "iface"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + status = "disabled"; >> + >> + i2c at 124a0000 { >> + compatible = "qcom,i2c-qup-v1.1.1"; >> + reg = <0x124a0000 0x1000>; >> + interrupts = <0 196 0>; > > Again, IRQ_TYPE_NONE possibly? Indeed, I'll change on v3. Thanks. > > Cheers, > Andreas > >> + >> + clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; >> + clock-names = "core", "iface"; >> + status = "disabled"; >> + >> + #address-cells = <1>; >> + #size-cells = <0>; >> + }; >> + }; >> + >> gsbi7: gsbi at 16600000 { >> status = "disabled"; >> compatible = "qcom,gsbi-v1.0.0"; > > -- > SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany > GF: Jeff Hawn, Jennifer Guild, Felix Imend?rffer; HRB 16746 AG N?rnberg > ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2014-08-26 9:42 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-08-20 12:02 [PATCH v2] ARM: apq8064: Add pinmux and i2c pinctrl nodes Kiran Padwal
2014-08-20 12:02 ` Kiran Padwal
2014-08-20 12:02 ` Kiran Padwal
2014-08-20 15:36 ` Andreas Färber
2014-08-20 15:36 ` Andreas Färber
[not found] ` <53F4C085.5060101-l3A5Bk7waGM@public.gmane.org>
2014-08-26 9:42 ` kiran.padwal-edOiRQu9Xnj5XLMNweQjbQ
2014-08-26 9:42 ` kiran.padwal
2014-08-26 9:42 ` kiran.padwal at smartplayin.com
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.