* [PATCH v4 1/3] cap11xx: make driver generic for variant support
2014-09-30 4:26 [PATCH v4 0/3] cap1106: add support for cap11xx variants Matt Ranostay
@ 2014-09-30 4:26 ` Matt Ranostay
2014-09-30 4:26 ` [PATCH v4 2/3] cap11xx: Add support for various cap11xx devices Matt Ranostay
2014-09-30 4:26 ` [PATCH v4 3/3] cap11xx: support for irq-active-high option Matt Ranostay
2 siblings, 0 replies; 6+ messages in thread
From: Matt Ranostay @ 2014-09-30 4:26 UTC (permalink / raw)
To: galak, dmitry.torokhov, zonque, linux-input, linux-kernel,
robh+dt
Cc: devicetree, Matt Ranostay
cap1106 driver can support much more one device make the driver
generic for support of similiar parts.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
---
.../bindings/input/{cap1106.txt => cap11xx.txt} | 5 +-
drivers/input/keyboard/Kconfig | 8 +-
drivers/input/keyboard/Makefile | 2 +-
drivers/input/keyboard/cap1106.c | 341 ---------------------
drivers/input/keyboard/cap11xx.c | 340 ++++++++++++++++++++
5 files changed, 348 insertions(+), 348 deletions(-)
rename Documentation/devicetree/bindings/input/{cap1106.txt => cap11xx.txt} (89%)
delete mode 100644 drivers/input/keyboard/cap1106.c
create mode 100644 drivers/input/keyboard/cap11xx.c
diff --git a/Documentation/devicetree/bindings/input/cap1106.txt b/Documentation/devicetree/bindings/input/cap11xx.txt
similarity index 89%
rename from Documentation/devicetree/bindings/input/cap1106.txt
rename to Documentation/devicetree/bindings/input/cap11xx.txt
index 4b46390..738f5f3 100644
--- a/Documentation/devicetree/bindings/input/cap1106.txt
+++ b/Documentation/devicetree/bindings/input/cap11xx.txt
@@ -1,11 +1,12 @@
-Device tree bindings for Microchip CAP1106, 6 channel capacitive touch sensor
+Device tree bindings for Microchip CAP1106 based capacitive touch sensor
The node for this driver must be a child of a I2C controller node, as the
device communication via I2C only.
Required properties:
- compatible: Must be "microchip,cap1106"
+ compatible: Must be on the following, depending on the model:
+ "microchip,cap1106"
reg: The I2C slave address of the device.
Only 0x28 is valid.
diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
index a3958c6..96ee26c 100644
--- a/drivers/input/keyboard/Kconfig
+++ b/drivers/input/keyboard/Kconfig
@@ -665,14 +665,14 @@ config KEYBOARD_CROS_EC
To compile this driver as a module, choose M here: the
module will be called cros_ec_keyb.
-config KEYBOARD_CAP1106
- tristate "Microchip CAP1106 touch sensor"
+config KEYBOARD_CAP11XX
+ tristate "Microchip CAP11XX based touch sensors"
depends on OF && I2C
select REGMAP_I2C
help
- Say Y here to enable the CAP1106 touch sensor driver.
+ Say Y here to enable the CAP11XX touch sensor driver.
To compile this driver as a module, choose M here: the
- module will be called cap1106.
+ module will be called cap11xx.
endif
diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
index 0a33456..febafa5 100644
--- a/drivers/input/keyboard/Makefile
+++ b/drivers/input/keyboard/Makefile
@@ -11,7 +11,7 @@ obj-$(CONFIG_KEYBOARD_AMIGA) += amikbd.o
obj-$(CONFIG_KEYBOARD_ATARI) += atakbd.o
obj-$(CONFIG_KEYBOARD_ATKBD) += atkbd.o
obj-$(CONFIG_KEYBOARD_BFIN) += bf54x-keys.o
-obj-$(CONFIG_KEYBOARD_CAP1106) += cap1106.o
+obj-$(CONFIG_KEYBOARD_CAP11XX) += cap11xx.o
obj-$(CONFIG_KEYBOARD_CLPS711X) += clps711x-keypad.o
obj-$(CONFIG_KEYBOARD_CROS_EC) += cros_ec_keyb.o
obj-$(CONFIG_KEYBOARD_DAVINCI) += davinci_keyscan.o
diff --git a/drivers/input/keyboard/cap1106.c b/drivers/input/keyboard/cap1106.c
deleted file mode 100644
index d70b65a..0000000
--- a/drivers/input/keyboard/cap1106.c
+++ /dev/null
@@ -1,341 +0,0 @@
-/*
- * Input driver for Microchip CAP1106, 6 channel capacitive touch sensor
- *
- * http://www.microchip.com/wwwproducts/Devices.aspx?product=CAP1106
- *
- * (c) 2014 Daniel Mack <linux@zonque.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/input.h>
-#include <linux/of_irq.h>
-#include <linux/regmap.h>
-#include <linux/i2c.h>
-#include <linux/gpio/consumer.h>
-
-#define CAP1106_REG_MAIN_CONTROL 0x00
-#define CAP1106_REG_MAIN_CONTROL_GAIN_SHIFT (6)
-#define CAP1106_REG_MAIN_CONTROL_GAIN_MASK (0xc0)
-#define CAP1106_REG_MAIN_CONTROL_DLSEEP BIT(4)
-#define CAP1106_REG_GENERAL_STATUS 0x02
-#define CAP1106_REG_SENSOR_INPUT 0x03
-#define CAP1106_REG_NOISE_FLAG_STATUS 0x0a
-#define CAP1106_REG_SENOR_DELTA(X) (0x10 + (X))
-#define CAP1106_REG_SENSITIVITY_CONTROL 0x1f
-#define CAP1106_REG_CONFIG 0x20
-#define CAP1106_REG_SENSOR_ENABLE 0x21
-#define CAP1106_REG_SENSOR_CONFIG 0x22
-#define CAP1106_REG_SENSOR_CONFIG2 0x23
-#define CAP1106_REG_SAMPLING_CONFIG 0x24
-#define CAP1106_REG_CALIBRATION 0x26
-#define CAP1106_REG_INT_ENABLE 0x27
-#define CAP1106_REG_REPEAT_RATE 0x28
-#define CAP1106_REG_MT_CONFIG 0x2a
-#define CAP1106_REG_MT_PATTERN_CONFIG 0x2b
-#define CAP1106_REG_MT_PATTERN 0x2d
-#define CAP1106_REG_RECALIB_CONFIG 0x2f
-#define CAP1106_REG_SENSOR_THRESH(X) (0x30 + (X))
-#define CAP1106_REG_SENSOR_NOISE_THRESH 0x38
-#define CAP1106_REG_STANDBY_CHANNEL 0x40
-#define CAP1106_REG_STANDBY_CONFIG 0x41
-#define CAP1106_REG_STANDBY_SENSITIVITY 0x42
-#define CAP1106_REG_STANDBY_THRESH 0x43
-#define CAP1106_REG_CONFIG2 0x44
-#define CAP1106_REG_SENSOR_BASE_CNT(X) (0x50 + (X))
-#define CAP1106_REG_SENSOR_CALIB (0xb1 + (X))
-#define CAP1106_REG_SENSOR_CALIB_LSB1 0xb9
-#define CAP1106_REG_SENSOR_CALIB_LSB2 0xba
-#define CAP1106_REG_PRODUCT_ID 0xfd
-#define CAP1106_REG_MANUFACTURER_ID 0xfe
-#define CAP1106_REG_REVISION 0xff
-
-#define CAP1106_NUM_CHN 6
-#define CAP1106_PRODUCT_ID 0x55
-#define CAP1106_MANUFACTURER_ID 0x5d
-
-struct cap1106_priv {
- struct regmap *regmap;
- struct input_dev *idev;
-
- /* config */
- unsigned short keycodes[CAP1106_NUM_CHN];
-};
-
-static const struct reg_default cap1106_reg_defaults[] = {
- { CAP1106_REG_MAIN_CONTROL, 0x00 },
- { CAP1106_REG_GENERAL_STATUS, 0x00 },
- { CAP1106_REG_SENSOR_INPUT, 0x00 },
- { CAP1106_REG_NOISE_FLAG_STATUS, 0x00 },
- { CAP1106_REG_SENSITIVITY_CONTROL, 0x2f },
- { CAP1106_REG_CONFIG, 0x20 },
- { CAP1106_REG_SENSOR_ENABLE, 0x3f },
- { CAP1106_REG_SENSOR_CONFIG, 0xa4 },
- { CAP1106_REG_SENSOR_CONFIG2, 0x07 },
- { CAP1106_REG_SAMPLING_CONFIG, 0x39 },
- { CAP1106_REG_CALIBRATION, 0x00 },
- { CAP1106_REG_INT_ENABLE, 0x3f },
- { CAP1106_REG_REPEAT_RATE, 0x3f },
- { CAP1106_REG_MT_CONFIG, 0x80 },
- { CAP1106_REG_MT_PATTERN_CONFIG, 0x00 },
- { CAP1106_REG_MT_PATTERN, 0x3f },
- { CAP1106_REG_RECALIB_CONFIG, 0x8a },
- { CAP1106_REG_SENSOR_THRESH(0), 0x40 },
- { CAP1106_REG_SENSOR_THRESH(1), 0x40 },
- { CAP1106_REG_SENSOR_THRESH(2), 0x40 },
- { CAP1106_REG_SENSOR_THRESH(3), 0x40 },
- { CAP1106_REG_SENSOR_THRESH(4), 0x40 },
- { CAP1106_REG_SENSOR_THRESH(5), 0x40 },
- { CAP1106_REG_SENSOR_NOISE_THRESH, 0x01 },
- { CAP1106_REG_STANDBY_CHANNEL, 0x00 },
- { CAP1106_REG_STANDBY_CONFIG, 0x39 },
- { CAP1106_REG_STANDBY_SENSITIVITY, 0x02 },
- { CAP1106_REG_STANDBY_THRESH, 0x40 },
- { CAP1106_REG_CONFIG2, 0x40 },
- { CAP1106_REG_SENSOR_CALIB_LSB1, 0x00 },
- { CAP1106_REG_SENSOR_CALIB_LSB2, 0x00 },
-};
-
-static bool cap1106_volatile_reg(struct device *dev, unsigned int reg)
-{
- switch (reg) {
- case CAP1106_REG_MAIN_CONTROL:
- case CAP1106_REG_SENSOR_INPUT:
- case CAP1106_REG_SENOR_DELTA(0):
- case CAP1106_REG_SENOR_DELTA(1):
- case CAP1106_REG_SENOR_DELTA(2):
- case CAP1106_REG_SENOR_DELTA(3):
- case CAP1106_REG_SENOR_DELTA(4):
- case CAP1106_REG_SENOR_DELTA(5):
- case CAP1106_REG_PRODUCT_ID:
- case CAP1106_REG_MANUFACTURER_ID:
- case CAP1106_REG_REVISION:
- return true;
- }
-
- return false;
-}
-
-static const struct regmap_config cap1106_regmap_config = {
- .reg_bits = 8,
- .val_bits = 8,
-
- .max_register = CAP1106_REG_REVISION,
- .reg_defaults = cap1106_reg_defaults,
-
- .num_reg_defaults = ARRAY_SIZE(cap1106_reg_defaults),
- .cache_type = REGCACHE_RBTREE,
- .volatile_reg = cap1106_volatile_reg,
-};
-
-static irqreturn_t cap1106_thread_func(int irq_num, void *data)
-{
- struct cap1106_priv *priv = data;
- unsigned int status;
- int ret, i;
-
- /*
- * Deassert interrupt. This needs to be done before reading the status
- * registers, which will not carry valid values otherwise.
- */
- ret = regmap_update_bits(priv->regmap, CAP1106_REG_MAIN_CONTROL, 1, 0);
- if (ret < 0)
- goto out;
-
- ret = regmap_read(priv->regmap, CAP1106_REG_SENSOR_INPUT, &status);
- if (ret < 0)
- goto out;
-
- for (i = 0; i < CAP1106_NUM_CHN; i++)
- input_report_key(priv->idev, priv->keycodes[i],
- status & (1 << i));
-
- input_sync(priv->idev);
-
-out:
- return IRQ_HANDLED;
-}
-
-static int cap1106_set_sleep(struct cap1106_priv *priv, bool sleep)
-{
- return regmap_update_bits(priv->regmap, CAP1106_REG_MAIN_CONTROL,
- CAP1106_REG_MAIN_CONTROL_DLSEEP,
- sleep ? CAP1106_REG_MAIN_CONTROL_DLSEEP : 0);
-}
-
-static int cap1106_input_open(struct input_dev *idev)
-{
- struct cap1106_priv *priv = input_get_drvdata(idev);
-
- return cap1106_set_sleep(priv, false);
-}
-
-static void cap1106_input_close(struct input_dev *idev)
-{
- struct cap1106_priv *priv = input_get_drvdata(idev);
-
- cap1106_set_sleep(priv, true);
-}
-
-static int cap1106_i2c_probe(struct i2c_client *i2c_client,
- const struct i2c_device_id *id)
-{
- struct device *dev = &i2c_client->dev;
- struct cap1106_priv *priv;
- struct device_node *node;
- int i, error, irq, gain = 0;
- unsigned int val, rev;
- u32 gain32, keycodes[CAP1106_NUM_CHN];
-
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
-
- priv->regmap = devm_regmap_init_i2c(i2c_client, &cap1106_regmap_config);
- if (IS_ERR(priv->regmap))
- return PTR_ERR(priv->regmap);
-
- error = regmap_read(priv->regmap, CAP1106_REG_PRODUCT_ID, &val);
- if (error)
- return error;
-
- if (val != CAP1106_PRODUCT_ID) {
- dev_err(dev, "Product ID: Got 0x%02x, expected 0x%02x\n",
- val, CAP1106_PRODUCT_ID);
- return -ENODEV;
- }
-
- error = regmap_read(priv->regmap, CAP1106_REG_MANUFACTURER_ID, &val);
- if (error)
- return error;
-
- if (val != CAP1106_MANUFACTURER_ID) {
- dev_err(dev, "Manufacturer ID: Got 0x%02x, expected 0x%02x\n",
- val, CAP1106_MANUFACTURER_ID);
- return -ENODEV;
- }
-
- error = regmap_read(priv->regmap, CAP1106_REG_REVISION, &rev);
- if (error < 0)
- return error;
-
- dev_info(dev, "CAP1106 detected, revision 0x%02x\n", rev);
- i2c_set_clientdata(i2c_client, priv);
- node = dev->of_node;
-
- if (!of_property_read_u32(node, "microchip,sensor-gain", &gain32)) {
- if (is_power_of_2(gain32) && gain32 <= 8)
- gain = ilog2(gain32);
- else
- dev_err(dev, "Invalid sensor-gain value %d\n", gain32);
- }
-
- BUILD_BUG_ON(ARRAY_SIZE(keycodes) != ARRAY_SIZE(priv->keycodes));
-
- /* Provide some useful defaults */
- for (i = 0; i < ARRAY_SIZE(keycodes); i++)
- keycodes[i] = KEY_A + i;
-
- of_property_read_u32_array(node, "linux,keycodes",
- keycodes, ARRAY_SIZE(keycodes));
-
- for (i = 0; i < ARRAY_SIZE(keycodes); i++)
- priv->keycodes[i] = keycodes[i];
-
- error = regmap_update_bits(priv->regmap, CAP1106_REG_MAIN_CONTROL,
- CAP1106_REG_MAIN_CONTROL_GAIN_MASK,
- gain << CAP1106_REG_MAIN_CONTROL_GAIN_SHIFT);
- if (error)
- return error;
-
- /* Disable autorepeat. The Linux input system has its own handling. */
- error = regmap_write(priv->regmap, CAP1106_REG_REPEAT_RATE, 0);
- if (error)
- return error;
-
- priv->idev = devm_input_allocate_device(dev);
- if (!priv->idev)
- return -ENOMEM;
-
- priv->idev->name = "CAP1106 capacitive touch sensor";
- priv->idev->id.bustype = BUS_I2C;
- priv->idev->evbit[0] = BIT_MASK(EV_KEY);
-
- if (of_property_read_bool(node, "autorepeat"))
- __set_bit(EV_REP, priv->idev->evbit);
-
- for (i = 0; i < CAP1106_NUM_CHN; i++)
- __set_bit(priv->keycodes[i], priv->idev->keybit);
-
- __clear_bit(KEY_RESERVED, priv->idev->keybit);
-
- priv->idev->keycode = priv->keycodes;
- priv->idev->keycodesize = sizeof(priv->keycodes[0]);
- priv->idev->keycodemax = ARRAY_SIZE(priv->keycodes);
-
- priv->idev->id.vendor = CAP1106_MANUFACTURER_ID;
- priv->idev->id.product = CAP1106_PRODUCT_ID;
- priv->idev->id.version = rev;
-
- priv->idev->open = cap1106_input_open;
- priv->idev->close = cap1106_input_close;
-
- input_set_drvdata(priv->idev, priv);
-
- /*
- * Put the device in deep sleep mode for now.
- * ->open() will bring it back once the it is actually needed.
- */
- cap1106_set_sleep(priv, true);
-
- error = input_register_device(priv->idev);
- if (error)
- return error;
-
- irq = irq_of_parse_and_map(node, 0);
- if (!irq) {
- dev_err(dev, "Unable to parse or map IRQ\n");
- return -ENXIO;
- }
-
- error = devm_request_threaded_irq(dev, irq, NULL, cap1106_thread_func,
- IRQF_ONESHOT, dev_name(dev), priv);
- if (error)
- return error;
-
- return 0;
-}
-
-static const struct of_device_id cap1106_dt_ids[] = {
- { .compatible = "microchip,cap1106", },
- {}
-};
-MODULE_DEVICE_TABLE(of, cap1106_dt_ids);
-
-static const struct i2c_device_id cap1106_i2c_ids[] = {
- { "cap1106", 0 },
- {}
-};
-MODULE_DEVICE_TABLE(i2c, cap1106_i2c_ids);
-
-static struct i2c_driver cap1106_i2c_driver = {
- .driver = {
- .name = "cap1106",
- .owner = THIS_MODULE,
- .of_match_table = cap1106_dt_ids,
- },
- .id_table = cap1106_i2c_ids,
- .probe = cap1106_i2c_probe,
-};
-
-module_i2c_driver(cap1106_i2c_driver);
-
-MODULE_ALIAS("platform:cap1106");
-MODULE_DESCRIPTION("Microchip CAP1106 driver");
-MODULE_AUTHOR("Daniel Mack <linux@zonque.org>");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/input/keyboard/cap11xx.c b/drivers/input/keyboard/cap11xx.c
new file mode 100644
index 0000000..0da2e83
--- /dev/null
+++ b/drivers/input/keyboard/cap11xx.c
@@ -0,0 +1,340 @@
+/*
+ * Input driver for Microchip CAP11xx based capacitive touch sensors
+ *
+ *
+ * (c) 2014 Daniel Mack <linux@zonque.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/input.h>
+#include <linux/of_irq.h>
+#include <linux/regmap.h>
+#include <linux/i2c.h>
+#include <linux/gpio/consumer.h>
+
+#define CAP11XX_REG_MAIN_CONTROL 0x00
+#define CAP11XX_REG_MAIN_CONTROL_GAIN_SHIFT (6)
+#define CAP11XX_REG_MAIN_CONTROL_GAIN_MASK (0xc0)
+#define CAP11XX_REG_MAIN_CONTROL_DLSEEP BIT(4)
+#define CAP11XX_REG_GENERAL_STATUS 0x02
+#define CAP11XX_REG_SENSOR_INPUT 0x03
+#define CAP11XX_REG_NOISE_FLAG_STATUS 0x0a
+#define CAP11XX_REG_SENOR_DELTA(X) (0x10 + (X))
+#define CAP11XX_REG_SENSITIVITY_CONTROL 0x1f
+#define CAP11XX_REG_CONFIG 0x20
+#define CAP11XX_REG_SENSOR_ENABLE 0x21
+#define CAP11XX_REG_SENSOR_CONFIG 0x22
+#define CAP11XX_REG_SENSOR_CONFIG2 0x23
+#define CAP11XX_REG_SAMPLING_CONFIG 0x24
+#define CAP11XX_REG_CALIBRATION 0x26
+#define CAP11XX_REG_INT_ENABLE 0x27
+#define CAP11XX_REG_REPEAT_RATE 0x28
+#define CAP11XX_REG_MT_CONFIG 0x2a
+#define CAP11XX_REG_MT_PATTERN_CONFIG 0x2b
+#define CAP11XX_REG_MT_PATTERN 0x2d
+#define CAP11XX_REG_RECALIB_CONFIG 0x2f
+#define CAP11XX_REG_SENSOR_THRESH(X) (0x30 + (X))
+#define CAP11XX_REG_SENSOR_NOISE_THRESH 0x38
+#define CAP11XX_REG_STANDBY_CHANNEL 0x40
+#define CAP11XX_REG_STANDBY_CONFIG 0x41
+#define CAP11XX_REG_STANDBY_SENSITIVITY 0x42
+#define CAP11XX_REG_STANDBY_THRESH 0x43
+#define CAP11XX_REG_CONFIG2 0x44
+#define CAP11XX_REG_SENSOR_BASE_CNT(X) (0x50 + (X))
+#define CAP11XX_REG_SENSOR_CALIB (0xb1 + (X))
+#define CAP11XX_REG_SENSOR_CALIB_LSB1 0xb9
+#define CAP11XX_REG_SENSOR_CALIB_LSB2 0xba
+#define CAP11XX_REG_PRODUCT_ID 0xfd
+#define CAP11XX_REG_MANUFACTURER_ID 0xfe
+#define CAP11XX_REG_REVISION 0xff
+
+#define CAP11XX_NUM_CHN 6
+#define CAP11XX_PRODUCT_ID 0x55
+#define CAP11XX_MANUFACTURER_ID 0x5d
+
+struct cap11xx_priv {
+ struct regmap *regmap;
+ struct input_dev *idev;
+
+ /* config */
+ unsigned short keycodes[CAP11XX_NUM_CHN];
+};
+
+static const struct reg_default cap11xx_reg_defaults[] = {
+ { CAP11XX_REG_MAIN_CONTROL, 0x00 },
+ { CAP11XX_REG_GENERAL_STATUS, 0x00 },
+ { CAP11XX_REG_SENSOR_INPUT, 0x00 },
+ { CAP11XX_REG_NOISE_FLAG_STATUS, 0x00 },
+ { CAP11XX_REG_SENSITIVITY_CONTROL, 0x2f },
+ { CAP11XX_REG_CONFIG, 0x20 },
+ { CAP11XX_REG_SENSOR_ENABLE, 0x3f },
+ { CAP11XX_REG_SENSOR_CONFIG, 0xa4 },
+ { CAP11XX_REG_SENSOR_CONFIG2, 0x07 },
+ { CAP11XX_REG_SAMPLING_CONFIG, 0x39 },
+ { CAP11XX_REG_CALIBRATION, 0x00 },
+ { CAP11XX_REG_INT_ENABLE, 0x3f },
+ { CAP11XX_REG_REPEAT_RATE, 0x3f },
+ { CAP11XX_REG_MT_CONFIG, 0x80 },
+ { CAP11XX_REG_MT_PATTERN_CONFIG, 0x00 },
+ { CAP11XX_REG_MT_PATTERN, 0x3f },
+ { CAP11XX_REG_RECALIB_CONFIG, 0x8a },
+ { CAP11XX_REG_SENSOR_THRESH(0), 0x40 },
+ { CAP11XX_REG_SENSOR_THRESH(1), 0x40 },
+ { CAP11XX_REG_SENSOR_THRESH(2), 0x40 },
+ { CAP11XX_REG_SENSOR_THRESH(3), 0x40 },
+ { CAP11XX_REG_SENSOR_THRESH(4), 0x40 },
+ { CAP11XX_REG_SENSOR_THRESH(5), 0x40 },
+ { CAP11XX_REG_SENSOR_NOISE_THRESH, 0x01 },
+ { CAP11XX_REG_STANDBY_CHANNEL, 0x00 },
+ { CAP11XX_REG_STANDBY_CONFIG, 0x39 },
+ { CAP11XX_REG_STANDBY_SENSITIVITY, 0x02 },
+ { CAP11XX_REG_STANDBY_THRESH, 0x40 },
+ { CAP11XX_REG_CONFIG2, 0x40 },
+ { CAP11XX_REG_SENSOR_CALIB_LSB1, 0x00 },
+ { CAP11XX_REG_SENSOR_CALIB_LSB2, 0x00 },
+};
+
+static bool cap11xx_volatile_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case CAP11XX_REG_MAIN_CONTROL:
+ case CAP11XX_REG_SENSOR_INPUT:
+ case CAP11XX_REG_SENOR_DELTA(0):
+ case CAP11XX_REG_SENOR_DELTA(1):
+ case CAP11XX_REG_SENOR_DELTA(2):
+ case CAP11XX_REG_SENOR_DELTA(3):
+ case CAP11XX_REG_SENOR_DELTA(4):
+ case CAP11XX_REG_SENOR_DELTA(5):
+ case CAP11XX_REG_PRODUCT_ID:
+ case CAP11XX_REG_MANUFACTURER_ID:
+ case CAP11XX_REG_REVISION:
+ return true;
+ }
+
+ return false;
+}
+
+static const struct regmap_config cap11xx_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = CAP11XX_REG_REVISION,
+ .reg_defaults = cap11xx_reg_defaults,
+
+ .num_reg_defaults = ARRAY_SIZE(cap11xx_reg_defaults),
+ .cache_type = REGCACHE_RBTREE,
+ .volatile_reg = cap11xx_volatile_reg,
+};
+
+static irqreturn_t cap11xx_thread_func(int irq_num, void *data)
+{
+ struct cap11xx_priv *priv = data;
+ unsigned int status;
+ int ret, i;
+
+ /*
+ * Deassert interrupt. This needs to be done before reading the status
+ * registers, which will not carry valid values otherwise.
+ */
+ ret = regmap_update_bits(priv->regmap, CAP11XX_REG_MAIN_CONTROL, 1, 0);
+ if (ret < 0)
+ goto out;
+
+ ret = regmap_read(priv->regmap, CAP11XX_REG_SENSOR_INPUT, &status);
+ if (ret < 0)
+ goto out;
+
+ for (i = 0; i < CAP11XX_NUM_CHN; i++)
+ input_report_key(priv->idev, priv->keycodes[i],
+ status & (1 << i));
+
+ input_sync(priv->idev);
+
+out:
+ return IRQ_HANDLED;
+}
+
+static int cap11xx_set_sleep(struct cap11xx_priv *priv, bool sleep)
+{
+ return regmap_update_bits(priv->regmap, CAP11XX_REG_MAIN_CONTROL,
+ CAP11XX_REG_MAIN_CONTROL_DLSEEP,
+ sleep ? CAP11XX_REG_MAIN_CONTROL_DLSEEP : 0);
+}
+
+static int cap11xx_input_open(struct input_dev *idev)
+{
+ struct cap11xx_priv *priv = input_get_drvdata(idev);
+
+ return cap11xx_set_sleep(priv, false);
+}
+
+static void cap11xx_input_close(struct input_dev *idev)
+{
+ struct cap11xx_priv *priv = input_get_drvdata(idev);
+
+ cap11xx_set_sleep(priv, true);
+}
+
+static int cap11xx_i2c_probe(struct i2c_client *i2c_client,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &i2c_client->dev;
+ struct cap11xx_priv *priv;
+ struct device_node *node;
+ int i, error, irq, gain = 0;
+ unsigned int val, rev;
+ u32 gain32, keycodes[CAP11XX_NUM_CHN];
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->regmap = devm_regmap_init_i2c(i2c_client, &cap11xx_regmap_config);
+ if (IS_ERR(priv->regmap))
+ return PTR_ERR(priv->regmap);
+
+ error = regmap_read(priv->regmap, CAP11XX_REG_PRODUCT_ID, &val);
+ if (error)
+ return error;
+
+ if (val != CAP11XX_PRODUCT_ID) {
+ dev_err(dev, "Product ID: Got 0x%02x, expected 0x%02x\n",
+ val, CAP11XX_PRODUCT_ID);
+ return -ENODEV;
+ }
+
+ error = regmap_read(priv->regmap, CAP11XX_REG_MANUFACTURER_ID, &val);
+ if (error)
+ return error;
+
+ if (val != CAP11XX_MANUFACTURER_ID) {
+ dev_err(dev, "Manufacturer ID: Got 0x%02x, expected 0x%02x\n",
+ val, CAP11XX_MANUFACTURER_ID);
+ return -ENODEV;
+ }
+
+ error = regmap_read(priv->regmap, CAP11XX_REG_REVISION, &rev);
+ if (error < 0)
+ return error;
+
+ dev_info(dev, "CAP11XX detected, revision 0x%02x\n", rev);
+ i2c_set_clientdata(i2c_client, priv);
+ node = dev->of_node;
+
+ if (!of_property_read_u32(node, "microchip,sensor-gain", &gain32)) {
+ if (is_power_of_2(gain32) && gain32 <= 8)
+ gain = ilog2(gain32);
+ else
+ dev_err(dev, "Invalid sensor-gain value %d\n", gain32);
+ }
+
+ BUILD_BUG_ON(ARRAY_SIZE(keycodes) != ARRAY_SIZE(priv->keycodes));
+
+ /* Provide some useful defaults */
+ for (i = 0; i < ARRAY_SIZE(keycodes); i++)
+ keycodes[i] = KEY_A + i;
+
+ of_property_read_u32_array(node, "linux,keycodes",
+ keycodes, ARRAY_SIZE(keycodes));
+
+ for (i = 0; i < ARRAY_SIZE(keycodes); i++)
+ priv->keycodes[i] = keycodes[i];
+
+ error = regmap_update_bits(priv->regmap, CAP11XX_REG_MAIN_CONTROL,
+ CAP11XX_REG_MAIN_CONTROL_GAIN_MASK,
+ gain << CAP11XX_REG_MAIN_CONTROL_GAIN_SHIFT);
+ if (error)
+ return error;
+
+ /* Disable autorepeat. The Linux input system has its own handling. */
+ error = regmap_write(priv->regmap, CAP11XX_REG_REPEAT_RATE, 0);
+ if (error)
+ return error;
+
+ priv->idev = devm_input_allocate_device(dev);
+ if (!priv->idev)
+ return -ENOMEM;
+
+ priv->idev->name = "CAP11XX capacitive touch sensor";
+ priv->idev->id.bustype = BUS_I2C;
+ priv->idev->evbit[0] = BIT_MASK(EV_KEY);
+
+ if (of_property_read_bool(node, "autorepeat"))
+ __set_bit(EV_REP, priv->idev->evbit);
+
+ for (i = 0; i < CAP11XX_NUM_CHN; i++)
+ __set_bit(priv->keycodes[i], priv->idev->keybit);
+
+ __clear_bit(KEY_RESERVED, priv->idev->keybit);
+
+ priv->idev->keycode = priv->keycodes;
+ priv->idev->keycodesize = sizeof(priv->keycodes[0]);
+ priv->idev->keycodemax = ARRAY_SIZE(priv->keycodes);
+
+ priv->idev->id.vendor = CAP11XX_MANUFACTURER_ID;
+ priv->idev->id.product = CAP11XX_PRODUCT_ID;
+ priv->idev->id.version = rev;
+
+ priv->idev->open = cap11xx_input_open;
+ priv->idev->close = cap11xx_input_close;
+
+ input_set_drvdata(priv->idev, priv);
+
+ /*
+ * Put the device in deep sleep mode for now.
+ * ->open() will bring it back once the it is actually needed.
+ */
+ cap11xx_set_sleep(priv, true);
+
+ error = input_register_device(priv->idev);
+ if (error)
+ return error;
+
+ irq = irq_of_parse_and_map(node, 0);
+ if (!irq) {
+ dev_err(dev, "Unable to parse or map IRQ\n");
+ return -ENXIO;
+ }
+
+ error = devm_request_threaded_irq(dev, irq, NULL, cap11xx_thread_func,
+ IRQF_ONESHOT, dev_name(dev), priv);
+ if (error)
+ return error;
+
+ return 0;
+}
+
+static const struct of_device_id cap11xx_dt_ids[] = {
+ { .compatible = "microchip,cap1106", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, cap11xx_dt_ids);
+
+static const struct i2c_device_id cap11xx_i2c_ids[] = {
+ { "cap1106", 0 },
+ {}
+};
+MODULE_DEVICE_TABLE(i2c, cap11xx_i2c_ids);
+
+static struct i2c_driver cap11xx_i2c_driver = {
+ .driver = {
+ .name = "cap11xx",
+ .owner = THIS_MODULE,
+ .of_match_table = cap11xx_dt_ids,
+ },
+ .id_table = cap11xx_i2c_ids,
+ .probe = cap11xx_i2c_probe,
+};
+
+module_i2c_driver(cap11xx_i2c_driver);
+
+MODULE_ALIAS("platform:cap11xx");
+MODULE_DESCRIPTION("Microchip CAP11XX driver");
+MODULE_AUTHOR("Daniel Mack <linux@zonque.org>");
+MODULE_LICENSE("GPL v2");
--
1.9.1
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH v4 2/3] cap11xx: Add support for various cap11xx devices
2014-09-30 4:26 [PATCH v4 0/3] cap1106: add support for cap11xx variants Matt Ranostay
2014-09-30 4:26 ` [PATCH v4 1/3] cap11xx: make driver generic for variant support Matt Ranostay
@ 2014-09-30 4:26 ` Matt Ranostay
2014-10-08 0:09 ` Dmitry Torokhov
2014-09-30 4:26 ` [PATCH v4 3/3] cap11xx: support for irq-active-high option Matt Ranostay
2 siblings, 1 reply; 6+ messages in thread
From: Matt Ranostay @ 2014-09-30 4:26 UTC (permalink / raw)
To: galak, dmitry.torokhov, zonque, linux-input, linux-kernel,
robh+dt
Cc: devicetree, Matt Ranostay
Several other variants of the cap11xx device exists with a varying
number of capacitance detection channels. Add support for creating
the channels dynamically.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
---
.../devicetree/bindings/input/cap11xx.txt | 3 +-
drivers/input/keyboard/cap11xx.c | 65 +++++++++++++++-------
2 files changed, 46 insertions(+), 22 deletions(-)
diff --git a/Documentation/devicetree/bindings/input/cap11xx.txt b/Documentation/devicetree/bindings/input/cap11xx.txt
index 738f5f3..8031aa5 100644
--- a/Documentation/devicetree/bindings/input/cap11xx.txt
+++ b/Documentation/devicetree/bindings/input/cap11xx.txt
@@ -7,9 +7,10 @@ Required properties:
compatible: Must be on the following, depending on the model:
"microchip,cap1106"
+ "microchip,cap1126"
+ "microchip,cap1188"
reg: The I2C slave address of the device.
- Only 0x28 is valid.
interrupts: Property describing the interrupt line the
device's ALERT#/CM_IRQ# pin is connected to.
diff --git a/drivers/input/keyboard/cap11xx.c b/drivers/input/keyboard/cap11xx.c
index 0da2e83..adb979e 100644
--- a/drivers/input/keyboard/cap11xx.c
+++ b/drivers/input/keyboard/cap11xx.c
@@ -1,7 +1,6 @@
/*
* Input driver for Microchip CAP11xx based capacitive touch sensors
*
- *
* (c) 2014 Daniel Mack <linux@zonque.org>
*
* This program is free software; you can redistribute it and/or modify
@@ -54,8 +53,6 @@
#define CAP11XX_REG_MANUFACTURER_ID 0xfe
#define CAP11XX_REG_REVISION 0xff
-#define CAP11XX_NUM_CHN 6
-#define CAP11XX_PRODUCT_ID 0x55
#define CAP11XX_MANUFACTURER_ID 0x5d
struct cap11xx_priv {
@@ -63,7 +60,25 @@ struct cap11xx_priv {
struct input_dev *idev;
/* config */
- unsigned short keycodes[CAP11XX_NUM_CHN];
+ u32 *keycodes;
+ unsigned int num_channels;
+};
+
+struct cap11xx_hw_model {
+ uint8_t product_id;
+ unsigned int num_channels;
+};
+
+enum {
+ CAP1106,
+ CAP1126,
+ CAP1188,
+};
+
+struct cap11xx_hw_model cap11xx_devices[] = {
+ [CAP1106] = { .product_id = 0x55, .num_channels = 6 },
+ [CAP1126] = { .product_id = 0x53, .num_channels = 6 },
+ [CAP1188] = { .product_id = 0x50, .num_channels = 8 },
};
static const struct reg_default cap11xx_reg_defaults[] = {
@@ -150,7 +165,7 @@ static irqreturn_t cap11xx_thread_func(int irq_num, void *data)
if (ret < 0)
goto out;
- for (i = 0; i < CAP11XX_NUM_CHN; i++)
+ for (i = 0; i < priv->num_channels; i++)
input_report_key(priv->idev, priv->keycodes[i],
status & (1 << i));
@@ -187,14 +202,23 @@ static int cap11xx_i2c_probe(struct i2c_client *i2c_client,
struct device *dev = &i2c_client->dev;
struct cap11xx_priv *priv;
struct device_node *node;
+ struct cap11xx_hw_model *cap = &cap11xx_devices[id->driver_data];
int i, error, irq, gain = 0;
unsigned int val, rev;
- u32 gain32, keycodes[CAP11XX_NUM_CHN];
+ u32 gain32;
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
+ BUG_ON(!cap->num_channels);
+
+ priv->num_channels = cap->num_channels;
+ priv->keycodes = devm_kcalloc(dev,
+ priv->num_channels, sizeof(u32), GFP_KERNEL);
+ if (!priv->keycodes)
+ return -ENOMEM;
+
priv->regmap = devm_regmap_init_i2c(i2c_client, &cap11xx_regmap_config);
if (IS_ERR(priv->regmap))
return PTR_ERR(priv->regmap);
@@ -203,9 +227,9 @@ static int cap11xx_i2c_probe(struct i2c_client *i2c_client,
if (error)
return error;
- if (val != CAP11XX_PRODUCT_ID) {
+ if (val != cap->product_id) {
dev_err(dev, "Product ID: Got 0x%02x, expected 0x%02x\n",
- val, CAP11XX_PRODUCT_ID);
+ val, cap->product_id);
return -ENODEV;
}
@@ -234,17 +258,12 @@ static int cap11xx_i2c_probe(struct i2c_client *i2c_client,
dev_err(dev, "Invalid sensor-gain value %d\n", gain32);
}
- BUILD_BUG_ON(ARRAY_SIZE(keycodes) != ARRAY_SIZE(priv->keycodes));
-
/* Provide some useful defaults */
- for (i = 0; i < ARRAY_SIZE(keycodes); i++)
- keycodes[i] = KEY_A + i;
+ for (i = 0; i < priv->num_channels; i++)
+ priv->keycodes[i] = KEY_A + i;
of_property_read_u32_array(node, "linux,keycodes",
- keycodes, ARRAY_SIZE(keycodes));
-
- for (i = 0; i < ARRAY_SIZE(keycodes); i++)
- priv->keycodes[i] = keycodes[i];
+ priv->keycodes, priv->num_channels);
error = regmap_update_bits(priv->regmap, CAP11XX_REG_MAIN_CONTROL,
CAP11XX_REG_MAIN_CONTROL_GAIN_MASK,
@@ -268,17 +287,17 @@ static int cap11xx_i2c_probe(struct i2c_client *i2c_client,
if (of_property_read_bool(node, "autorepeat"))
__set_bit(EV_REP, priv->idev->evbit);
- for (i = 0; i < CAP11XX_NUM_CHN; i++)
+ for (i = 0; i < priv->num_channels; i++)
__set_bit(priv->keycodes[i], priv->idev->keybit);
__clear_bit(KEY_RESERVED, priv->idev->keybit);
priv->idev->keycode = priv->keycodes;
- priv->idev->keycodesize = sizeof(priv->keycodes[0]);
- priv->idev->keycodemax = ARRAY_SIZE(priv->keycodes);
+ priv->idev->keycodesize = sizeof(u32);
+ priv->idev->keycodemax = priv->num_channels;
priv->idev->id.vendor = CAP11XX_MANUFACTURER_ID;
- priv->idev->id.product = CAP11XX_PRODUCT_ID;
+ priv->idev->id.product = cap->product_id;
priv->idev->id.version = rev;
priv->idev->open = cap11xx_input_open;
@@ -312,12 +331,16 @@ static int cap11xx_i2c_probe(struct i2c_client *i2c_client,
static const struct of_device_id cap11xx_dt_ids[] = {
{ .compatible = "microchip,cap1106", },
+ { .compatible = "microchip,cap1126", },
+ { .compatible = "microchip,cap1188", },
{}
};
MODULE_DEVICE_TABLE(of, cap11xx_dt_ids);
static const struct i2c_device_id cap11xx_i2c_ids[] = {
- { "cap1106", 0 },
+ { "cap1106", CAP1106 },
+ { "cap1126", CAP1126 },
+ { "cap1188", CAP1188 },
{}
};
MODULE_DEVICE_TABLE(i2c, cap11xx_i2c_ids);
--
1.9.1
^ permalink raw reply related [flat|nested] 6+ messages in thread