From: "Lu, Ran" <hephooey@gmail.com>
To: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Subject: Help to enable Iris Pro on Retina MBP 11.3
Date: Sun, 05 Jan 2014 17:20:52 -0600 [thread overview]
Message-ID: <1420080.HpJ4UCjVfA@rmbp> (raw)
Hi guys,
I just got a Retina MBP with Iris Pro and Nvidia GT 750. The iGPU works in
OSX(Mavericks), but when I boot into Linux, the device was disabled. I
debugged the kernel a little, apparently when pci_bus_read_dev_vendor_id is
called for PCI 00:2.0 (the intel gpu), it returns -1 which indicates the
device is disabled.
I can check all the registers in grub using setpci or pcidump, so it seems
before boot into the kernel the device is actually online, and I am looking
for some magical registers that I can set to enable the device. I did a ioreg
-l in OSX and the information about Iris Pro looks like this:
| | | +-o IGPU@2 <class IOPCIDevice, id 0x100000227, registered, matched,
active, busy 0 (300 ms), retain 22>
| | | | | {
| | | | | "assigned-addresses" =
<1010008200000000000040c10000000000004000181000c27f000000000000b000000000000000102010008100000000002000000000000040000000>
| | | | | "IOInterruptSpecifiers" =
(<1000000007000000>,<0200000000000100>)
| | | | | "class-code" = <00000300>
| | | | | "IODeviceMemory" = (({"address"=3242196992,"length"=4194304}),
({"address"=548413636608,"length"=268435456}),"IOSubMemoryDescriptor is not
serializable")
| | | | | "AAPL,gray-page" = <01000000>
| | | | | "IOPowerManagement" =
{"ChildrenPowerState"=2,"CurrentPowerState"=2,"ChildProxyPowerState"=2,"MaxPowerState"=3}
| | | | | "subsystem-vendor-id" = <6b100000>
| | | | | "built-in" = <00>
| | | | | "acpi-device" = "IOACPIPlatformDevice is not serializable"
| | | | | "boot-gamma-restored" = <0000000000000000>
| | | | | "hda-gfx" = <"onboard-1">
| | | | | "IOInterruptControllers" = ("io-
apic-0","IOPCIMessagedInterruptController")
| | | | | "IOPCIMSIMode" = Yes
| | | | | "name" = <"display">
| | | | | "vendor-id" = <86800000>
| | | | | "device-id" = <260d0000>
| | | | | "graphic-options" = <0c000000>
| | | | | "IOPCIResourced" = Yes
| | | | | "compatible" =
<"pci106b,12f","pci8086,d26","pciclass,030000","IGPU">
| | | | | "saved-config" =
<47000000000000000000000000000000000003000900260d00a10700000000000000000000000000000000000000000000000000000000000000000000000000000000000000000101010100061022a0020240000000000000000002f0a72114400b0807a0000000340000003000200003000600400b0807002e00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000>
| | | | | "AAPL,iokit-ndrv" = <f00cfa947fffffff>
| | | | | "acpi-path" = "IOACPIPlane:/_SB/PCI0@0/IGPU@20000"
| | | | | "model" = <"Intel Iris Pro">
| | | | | "subsystem-id" = <2f010000>
| | | | | "revision-id" = <08000000>
| | | | | "AAPL,ig-platform-id" = <0900260d>
| | | | | "AAPL,gray-value" = <bfbfbf00>
| | | | | "pcidebug" = "0:2:0"
| | | | | "IOName" = "display"
| | | | | "attached-gpu-control-path" =
"IOService:/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/IGPU@2/AppleIntelFramebuffer@0/AGPM"
| | | | | "reg" =
<0010000000000000000000000000000000000000101000020000000000000000000000000000400018100042000000000000000000000000000000102010000100000000000000000000000040000000>
| | | | | "IOMemoryDescriptorOptions" = 2048
| | | | | }
The reg line looks interesting but it is also nothing like the number I got
from setpci in grub, so I am confused whether they are useful. Any help are
deeply appreciated! I also tried to check the newly released Haswell
documents, but did not find anything obvious.
--
Best Regards,
LR
next reply other threads:[~2014-01-05 23:22 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-01-05 23:20 Lu, Ran [this message]
2014-01-07 8:02 ` Help to enable Iris Pro on Retina MBP 11.3 Jani Nikula
2014-01-07 21:14 ` Lu, Ran
2014-01-08 9:12 ` Jani Nikula
2014-01-08 9:18 ` Dave Airlie
2014-01-08 14:53 ` Lu, Ran
2014-01-08 13:46 ` Steven Newbury
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1420080.HpJ4UCjVfA@rmbp \
--to=hephooey@gmail.com \
--cc=intel-gfx@lists.freedesktop.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.