[PATCH v12 2/6] fpga: add bindings document for simple fpga bus

[<atull@opensource.altera.com>]

From: Alan Tull <atull@opensource.altera.com>

New bindings document for simple fpga bus.

Signed-off-by: Alan Tull <atull@opensource.altera.com>
---
v9:  initial version added to this patchset
v10: s/fpga/FPGA/g
     replace DT overlay example with slightly more complicated example
     move to staging/simple-fpga-bus
v11: No change in this patch for v11 of the patch set
v12: Moved out of staging.
     Changed to use FPGA bridges framework instead of resets
     for bridges.
---
 .../devicetree/bindings/fpga/simple-fpga-bus.txt   |   81 ++++++++++++++++++++
 1 file changed, 81 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fpga/simple-fpga-bus.txt

diff --git a/Documentation/devicetree/bindings/fpga/simple-fpga-bus.txt b/Documentation/devicetree/bindings/fpga/simple-fpga-bus.txt
new file mode 100644
index 0000000..2e742f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/fpga/simple-fpga-bus.txt
@@ -0,0 +1,81 @@
+Simple FPGA Bus
+===============
+
+A Simple FPGA Bus is a bus that handles configuring an FPGA and its bridges
+before populating the devices below its node.  All this happens when a device
+tree overlay is added to the live tree.  This document describes that device
+tree overlay.
+
+Required properties:
+- compatible : should contain "simple-fpga-bus"
+- #address-cells, #size-cells, ranges: must be present to handle address space
+  mapping for children.
+
+Optional properties:
+- fpga-mgr : should contain a phandle to a FPGA manager.
+- fpga-firmware : should contain the name of a FPGA image file located on the
+  firmware search path.
+- partial-reconfig : boolean property should be defined if partial
+  reconfiguration of the FPGA is to be done, otherwise full reconfiguration
+  is done.
+- fpga-bridges : should contain a list of bridges that the bus will disable
+  before   programming the FPGA and then enable after the FPGA has been
+
+Example:
+
+/dts-v1/;
+/plugin/;
+/ {
+	fragment@0 {
+		target-path="/soc";
+		__overlay__ {
+			#address-cells = <1>;
+	                #size-cells = <1>;
+
+			bridge@0xff200000 {
+				compatible = "simple-fpga-bus";
+				reg = <0xc0000000 0x20000000>,
+				      <0xff200000 0x00200000>;
+				reg-names = "axi_h2f", "axi_h2f_lw";
+
+				#address-cells = <0x2>;
+				#size-cells = <0x1>;
+
+				ranges = <0x00000000 0x00000000 0xc0000000 0x00010000>,
+					 <0x00000001 0x00020000 0xff220000 0x00000008>,
+					 <0x00000001 0x00010040 0xff210040 0x00000020>;
+
+				clocks = <0x2 0x2>;
+				clock-names = "h2f_lw_axi_clock", "f2h_sdram0_clock";
+
+				fpga-mgr = <&hps_0_fpgamgr>;
+				fpga-firmware = "soc_system.rbf";
+
+				fpga-bridges = <&hps_fpgabridge0>, <&hps_fpgabridge1>, <&hps_fpgabridge2>;
+
+				onchip_memory2_0: memory@0x000000000 {
+					device_type = "memory";
+					compatible = "ALTR,onchipmem-15.1";
+					reg = <0x00000000 0x00000000 0x00010000>;
+				};
+
+				jtag_uart: serial@0x100020000 {
+					compatible = "altr,juart-15.1", "altr,juart-1.0";
+					reg = <0x00000001 0x00020000 0x00000008>;
+					interrupt-parent = <&intc>;
+					interrupts = <0 42 4>;
+				};
+
+				led_pio: gpio@0x100010040 {
+					compatible = "altr,pio-15.1", "altr,pio-1.0";
+					reg = <0x00000001 0x00010040 0x00000020>;
+					altr,gpio-bank-width = <4>;
+					resetvalue = <0>;
+					#gpio-cells = <2>;
+					gpio-controller;
+				};
+			};
+		};
+	};
+};
+
-- 
1.7.9.5