From: Jagan Teki <jagan@openedev.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v3 05/13] ARM: dts: imx6qdl-icore: Add FEC support
Date: Tue, 6 Dec 2016 00:00:52 +0100 [thread overview]
Message-ID: <1480978860-4351-6-git-send-email-jagan@openedev.com> (raw)
In-Reply-To: <1480978860-4351-1-git-send-email-jagan@openedev.com>
From: Jagan Teki <jagan@amarulasolutions.com>
Add FEC dts support for Engicam i.CoreM6 dql modules.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/imx6qdl-icore.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm/dts/imx6qdl-icore.dtsi b/arch/arm/dts/imx6qdl-icore.dtsi
index f424cd5..a485c3e 100644
--- a/arch/arm/dts/imx6qdl-icore.dtsi
+++ b/arch/arm/dts/imx6qdl-icore.dtsi
@@ -75,6 +75,14 @@
assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
};
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+ phy-mode = "rmii";
+ status = "okay";
+};
+
&gpmi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpmi_nand>;
@@ -118,6 +126,22 @@
};
&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b1
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1b0b0
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+
pinctrl_flexcan1: flexcan1grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b020
--
1.9.1
next prev parent reply other threads:[~2016-12-05 23:00 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-12-05 23:00 [U-Boot] [PATCH v3 00/13] imx6: icorem6: Add dm-eth, framebuffer and I2C support Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 01/13] net: fec_mxc: Remove unneeded eth_device arg from fec_get_hwaddr Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 02/13] net: fec_mxc: Convert into driver model Jagan Teki
2016-12-09 18:22 ` Joe Hershberger
2016-12-09 22:26 ` Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 03/13] net: fec_mxc: Driver cleanups Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 04/13] dm: net: fec: Add .read_rom_hwaddr Jagan Teki
2016-12-05 23:00 ` Jagan Teki [this message]
2016-12-05 23:00 ` [U-Boot] [PATCH v3 06/13] icorem6: Use CONFIG_DM_ETH support Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 07/13] video: Kconfig: Add VIDEO_IPV3 entry Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 08/13] imx6: icorem6: Add framebuffer support Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 09/13] imx6: icorem6: Add custom splashscreen support Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 10/13] i2c: Kconfig: Add SYS_I2C_MXC entry Jagan Teki
2016-12-06 14:06 ` Heiko Schocher
2016-12-06 15:45 ` Jagan Teki
2016-12-06 14:47 ` Fabio Estevam
2016-12-06 15:44 ` Jagan Teki
2016-12-05 23:00 ` [U-Boot] [PATCH v3 11/13] i2c: mxc: Print hex instead of decimal for bus address Jagan Teki
2016-12-06 14:07 ` Heiko Schocher
2016-12-05 23:00 ` [U-Boot] [PATCH v3 12/13] i2c: mxc: Make 'no gpio pinctrl state' print as debug Jagan Teki
2016-12-06 14:08 ` Heiko Schocher
2016-12-05 23:01 ` [U-Boot] [PATCH v3 13/13] imx6: icorem6: Add I2C support Jagan Teki
2016-12-06 14:10 ` Heiko Schocher
2016-12-06 17:25 ` Jagan Teki
2016-12-07 16:01 ` [U-Boot] [PATCH v3 00/13] imx6: icorem6: Add dm-eth, framebuffer and " Jagan Teki
2016-12-13 12:36 ` Jagan Teki
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1480978860-4351-6-git-send-email-jagan@openedev.com \
--to=jagan@openedev.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.