[PATCH 2/2] dt-bindings: phy-qcom-qusb2: Add SC7180 QUSB2 phy support

[Sandeep Maheswaram <sanm@codeaurora.org>]

Add QUSB2 phy entries for SC7180 in device tree bindings.

Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
---
 Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
index fe29f9e..d46fca7 100644
--- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
+++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
@@ -8,6 +8,7 @@ Required properties:
 	       "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
 	       "qcom,msm8998-qusb2-phy" for 10nm PHY on msm8998,
 	       "qcom,sdm845-qusb2-phy" for 10nm PHY on sdm845.
+	       "qcom,sc7180-qusb2-phy" for 8nm PHY on sc7180.
 
  - reg: offset and length of the PHY register set.
  - #phy-cells: must be 0.
@@ -31,23 +32,23 @@ Optional properties:
  - qcom,imp-res-offset-value: It is a 6 bit value that specifies offset to be
 		added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
 		tuning parameter that may vary for different boards of same SOC.
-		This property is applicable to only QUSB2 v2 PHY (sdm845).
+		This property is applicable to only QUSB2 v2 PHY (sdm845,sc7180).
  - qcom,hstx-trim-value: It is a 4 bit value that specifies tuning for HSTX
 		output current.
 		Possible range is - 15mA to 24mA (stepsize of 600 uA).
 		See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-		This property is applicable to only QUSB2 v2 PHY (sdm845).
+		This property is applicable to only QUSB2 v2 PHY (sdm845,sc7180).
 		Default value is 22.2mA for sdm845.
  - qcom,preemphasis-level: It is a 2 bit value that specifies pre-emphasis level.
 		Possible range is 0 to 15% (stepsize of 5%).
 		See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-		This property is applicable to only QUSB2 v2 PHY (sdm845).
+		This property is applicable to only QUSB2 v2 PHY (sdm845,sc7180).
 		Default value is 10% for sdm845.
 - qcom,preemphasis-width: It is a 1 bit value that specifies how long the HSTX
 		pre-emphasis (specified using qcom,preemphasis-level) must be in
 		effect. Duration could be half-bit of full-bit.
 		See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-		This property is applicable to only QUSB2 v2 PHY (sdm845).
+		This property is applicable to only QUSB2 v2 PHY (sdm845,sc7180).
 		Default value is full-bit width for sdm845.
 
 Example:
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation